Search Documents

By Owen Rice

CHANGES in coke hardness affect the working of the blast furnace, for soft coke is an obstacle to proper furnace operation. Soft coke is due to a low hydrogen-oxygen ratio in the coal charged; increasing this ratio increases the hardness of the coke. The best means of determining the hardness of coke is the combined tumbler and ball-mill. Soft coke is a great hindrance to proper blast-furnace operation and changes in coke hardness affect the working of the furnace. The best method of determining the hardness of coke is by using a combination tumbler-ball-mill. Soft coke is due to a low hydrogen-oxygen ratio in the coal charged. An increase of this ratio improves the hardness of the resulting coke. WHAT IS GOOD COKE? It is not always appreciated that the correct answer may be such a reliable forecast to the physical condition of the blast furnace, and incidentally its entire operation, that among the ordinary variations in other raw materials and also in operating conditions, it assumes a position of primary significance. Inasmuch as coke forms two-thirds of the total bulk of material charged, this assertion will not seem exaggerated, and in the subsequent discussion its applicability will be presented. Coke is the ideal blast-furnace fuel because it is strong and hard enough to resist the crushing and grinding effects of the furnace burden, and its porosity allows the ready passage of gas upward through the charge, and rapid combustion before the tuyeres. Coke deprived of its strength and with a cell structure physically frail and chemically susceptible to solution by carbon dioxide, has its chief asset eliminated. When the melting zones are approached the fluid cinder trickling toward the hearth will envelope the small pieces of coke and form a sticky mass that will retard the free passage of gas. Blast pressure will then rise, driving

Jan 1, 1921

By T. P. Papazoglou, N. A. D. Parlee, W. C. Phelps

PRACTICAL designs for good "home made" molybdenum furnaces are hard to find in the literature. The one described briefly below left something to be desired but was good enough to operate as a rather long (30 in.) two-zone furnace for periods of over 2 months at temperature (1400° to 1600°C) without shutdown. The principal problem in our application was to establish a temperature profile with two distinct constant-temperature zones and no dip between the zones. This and other problems mentioned below would not arise, however, if both zones were operated at the same temperature and if a shorter furnace were acceptable. Since molybdenum windings oxidize very rapidly when heated in air, impervious refractory tubes were used for both the furnace core and the outer jacket tube shown in the accompanying figures. A protective atmosphere of forming gas (10 pct H2, 90 pct N2) was continuously passed through the gas-tight annular volume between the core and outer jacket. The water-cooled copper ends shown in Figs. 1 to 3 sealed the ends of the tubes. Annealed molybdenum wire (40 mil) was wound on the recrys-tallized alumina core (35.5 mm OD by 28.5 mm ID by 30 in.) at a spacing of 0.36 in. The spacing was reduced to 0.29 in. close to the ends to partially compensate for end heat losses. Fig. 2 shows two molybdenum-ground lead taps off the center of the winding to produce the two independect temperature zones. The ground lead was insulated with 1/4-in. alumina tubing and connected to the grounded copper end by passing the wires through the gas port tube and crimping each wire into notches cut at the mouth. To prevent sagging of the core at high temperatures, refractory "troughs" were cut from alumina and mullite tubing to cradle the core. The support "troughs" which were 6 in. long and located about 5 in. from each end of the annular volume also served as radiation shields. In view of the different expansion coefficients and operating temperatures of the core and outer jacket (3.5 in. OD by 3 in. ID by 30 in.), the ends of the tubes were smoothed and squared to produce good sealing surfaces, and the core was ground 1/32 in. shorter than the outer tube. The power terminals were passed through their respective conductor ports which were internally lined with alumina tubing and sealed with Armstrong adhesive A-6 leaving about 1 in. of protruding lead wire for external connections. (Adhesive A-6 is a two-component system consisting of an epoxy-type resin with a mineral fibrous filler and an amine catalyst.) Figs. 1 and 3 show the entire assembly of concentric refractory tubes, copper ends, and sealing o rings, held together with two brass flanges and 3/8-in. bolts with heavy springs for dimensional flexibility. The furnace shell (19 by 19 by 30 in.) consisted of a steel frame with sheets of transite forming a box. The copper ends protruded through two 3.75-in. circular holes cut at the center of each transite square end. Thermal insulation next to the transite exterior was effected by K-23 B&W bricks alld in a central volume of approximately 9 by 9 by 30 in. a row of K-30 bricks was lined up to support the hot assembly. The rest of the volume around the outer

Jan 1, 1965

By James T. Gow, Oscar E. Harder, Anton de S. Brasunas

This paper deals with the results obtained and the techniques employed in determining: 1. Liquidus and solidus temperatures of the HH and HT type heat-resistant alloys. 2. The relation of true temperatures (thermocouple) to apparent temperatures (optical pyrometer) for the molten HH and HT type alloys. This work was the outgrowth of needing to know something definite about these temperatures in order to study the effect of pouring temperatures, shake-out times, and heat-treatments on the properties of some heat-resistant alloys. The information developed is thought to be of interest to industry for guidance in foundry practices and the industrial heat applications of the alloys. This paper is based upon work that has been done for the Alloy Casting Institute at Battellc Memorial Institute. Liquidus and Solidus Temperatures of HH and HT Type Alloys Experimenta1 Procedures Temperature-time curves were obtained during the cooling and solidification of several HH and HT type alloys. The metal was melted in an Ajax high-frequency, induction furnace and poured into a core-sand mold for cooling. The temperature measurements were obtained by means of a platinum, platinum-rhodium thermocouple contained within a fused silica sheath, which was extended through the side wall of the dry core-sand mold to a point at about the center of the mold cavity, which was 3 in. in diameter by 5 in. deep. The cold junction of the thermocouple was kept in an ice bottle, and the temperature was recorded automatically on a direct-reading potentiometer recorder. Through a switching arrangement, the temperature recorded was checked occasionally with a portable Leeds and North-rup potentiometer indicator. Less than a 5°F. variation in the two instruments was always found. This is within the limit of accuracy of readings. The thermocouple used was checked for accuracy against a standard couple, both before use on this work and after completion of the work, by the instrument laboratory. Temperature-time Cooling Curves Fig. I is an enlarged reproduction of a part of one of the cooling curves over the temperature range of 2600' to 2200°F. for an alloy of the HT type with 0.45 per cent carbon, 16 per cent chromium, and 36 per cent nickel. This is a typically shaped cooling curve as obtained for the alloys. It will be noted that two temperatures "re shown on Fig. I for the liquidus temperature. It is thought likely that the higher temperature, A, at the point at

Jan 1, 1945

By Marvin P. Barnes, John G. Simos

The Park City District, Utah, is situated in the Wasatch Range at the intersection of the westward extension of the axis of the Uinta Range. Ore has been mined almost continuously from the first discovery in 1869 to the present day, with a total production of over 14 million tons. Sediments of Carboniferous to Triassic age have been folded into the northerly plunging Park City anticline and subsequently modified by thrust faulting, diorite and diorite porphyry intrusions, and strong east-west normal faulting during the Laramide orogeny. Younger andesitic volcanics partially cover the eastern edge of the district. The ore bodies occur as both lode and bedded replacement deposits over widely scattered localities. Near surface, high-grade silver "bonanza" ores were mined in early days from the Ontario and Daly Lodes, which occur along the east-west zone of faulting near the center of the district. Other lode or fissure deposits were found along the Mayflower and Hawkeye faults to the east and southeast. Large bedded replacement silver-lead-zinc ore bodies associated with east-west zones of fissuring, have been mined from favorable horizons in the Park City Formation in the Daly West and Judge mines. A series of long, narrow, high-grade, replacement ore bodies occur in the Silver King mine at a single horizon in the Park City Formation. Ore is currently being mined from strong bedded replacements in the Humbug Formation near the apex of the Park City anticline. Factors controlling ore deposition are: magmatic source, structural feeder systems, and favorable host rocks. Ore deposition along favorable beds is primarily a function of physical conditioning and secondarily of chemical composition.

Jan 1, 1968

Adams, Benjamin C., Jr., Student, Univ. of Oklahoma Norman, Okla. '36 Adams, Ernest C., Student, Univ. of Illinois 908 W. Green St., Urbana, Ill. '35 Adams, George H., Student, Colorado School of Mines Golden, Colo. '36 Adams, Robert Keller Mitchell Hotel, No. 18, Golden, Colo. '35 Afshar, Hadji Khan A., Student Box 63, Univ. Sta., Moscow, Idaho. '36 Ahrenholz, Herman William, Jr., Student, Lehigh Univ Bethlehem, Pa. '35 Alger, Robert P., Student, Missouri School of Mines & Met.Rolla, Mo. '36 Allen, Paul W., Student, Mass. Inst. of Tech Cambridge, Mass. '35 Allen, R. M., Jr., Student, Virginia Polytechnic Inst., "G" Co.Blacksburg, Va. '35 Alley, John Arnold, Student, Montana School of Mines Butte, Mont. '36 Amberger, R. H., Student, Michigan College of Min. & Tech Houghton, Mich. '35 Ambrosiani, F. Peter, Student, Michigan College of Min. & Tech Houghton, Mich. '36 Andersen, Burton Lee, Student, School of Mines, Univ. of Washington Seattle, Wash. '36 Anderson, Carlos, Student, Univ. of Oklahoma Norman, Okla. '36 Anderson, J. Wendell, Student, Pennsylvania State College State College, Pa. '36 Anderson, Joseph S. Cornelia Hotel, Ajo, Ariz. '35 Anderson, R. C., Student, Univ. of Washington Seattle, Wash. '35 Anderson, Roy A., Student, Washington State College Pullman, Wash. '35 Anderson, Willard. Student. Univ. of Oklahoma Norman, Okla. '36

Jan 1, 1936

By Frank Wartman

RECENTLY Horace Freeman1 obtained a patent on a successful method of conducting a roasting procedure described as to general features by Carl Schnabel2 almost forty years ago. Essentially, the Freeman process of roasting consists in introducing the finely powdered sulfide mineral, suspended in air or any other suitable gaseous medium, into the upper portion of a heated chamber. The stream of suspended particles is directed vertically downward. A counter-current stream of gas introduced at the bottom of the chamber flows upward. The mineral particles are oxidized as they fall through the heated atmosphere of the chamber. All air required for the oxidation may be admitted either at the top or the bottom of the chamber, or may be divided between the top and bottom inlets in any desired proportion. Heat may be recovered by passing the gases leaving the furnace through a waste-heat boiler or other form of interchanger. In speaking of the results obtained in roasting pyrite, Freeman says:3 Steam yield from the boiler exceeds 1 pound of steam per pound of pyrite con-sumed, which pays the cost of operation of the burner. The oxide produced is in the form of fused particles or hollow shells of magnetite, containing about 65 per cent of iron. It contains the gangue material ordinarily produced in flotation concentrate, of course, but it is being found that most of this can be eliminated by magnetic separa-tion, and that the sulfur content, as consistently produced, is below 0.2 percent. This material is especially interesting as a high-grade iron ore, free from phosphorus and low in sulfur. It may be sintered or briquetted. It is even more interesting as a raw material for sponge-iron production, to be directly smelted in electric furnaces without the usual cooling of the iron powder and magnetic separation between the reducing kiln and the electric furnace.

Jan 1, 1933

By Charles Hawes

WHEN sulfur is encountered in objectionable amounts, it is regarded as the most trouble-some element for the mine operator to control. It exists in two conditions in iron ores, as sulfide in iron pyrites and as sulfate in gypsum and barite. The sulfate radical (SO,) may also be linked to one or more of the several other elements found in the iron ore compound. The only dependable method for the de-termination of sulfur, particularly when found in the insoluble residue, has been the so-called fusion method. This is a long and tedious process involving several hours for its completion. In looking for a more rapid method which would be .applicable to all iron ores, the writer investigated the work of M. Groger1 who in 1881 showed that by heating pyrite with iron out of contact with air, the pyrite is reduced to iron sulfide and from the latter all of the sulfur will be given off as hydrogen sulfide gas on treat-ment with hydrochloric acid. FeS2 + Fe = 2 FeS FeS + 2 HCl = FeC12 + H2S In 1891 F. P. Treadwell2 not only confirmed the results of M. Groger but also found that iron powder would reduce to sulfide the sulfate radical of any substance, including barite, if not found in excessive quantities. The writer found this to be true and developed a method, in cooperation with F. J. Baker, chief chemist, mining department, of the Cleveland-Cliffs Iron Co., Ishpeming, Mich., for the determination of sulfur in iron ores which is not only very rapid but also accurate. Pure iron ore powder, reduced by hydrogen, gave good results but was found to be very slow in reacting. A high silicon iron with a low sulfur content of 0.012 per cent was found to be. much more active than the pure iron and gave excellent results.

Jan 11, 1927

By M. J. Marcinkowski, E. N. Hopkins

An investigation has been made of the ß(fcc) — a(hexagonal) transformation which occurs in lanthanum using both electrical resistivity and transmission electron microscopy techniques. It has been shown that the ß phase can be retained below the transformation temperature by rapid quenching but that the sample immediately begins to transform to the a phase. The transformation is observed to nucleate in the vicinity of inclusions. Based on the above observations, a detailed model of the transformation has been advanced which involves the nucleation of an extrinsic stacking fault bounded by a pair of Shockley partial dislocations in the vicinity of some heterogeneity, i.e., an inclusion. The stress field of the resultant dislocation pair acts to nucleate extrinsic faults in adjacent planes and leads quite naturally to the B-a conversion with a minimum of strain energy induced in the crystal. LANTHANUM possesses an fcc structure ß) (8) upon cooling transforms to a hexagonal modification (a) in much the same way as cobalt. The one exception, however, is that the stacking sequence of the closest packed planes in a La is ABAC ABAC, and so forth,1 whereas in cobalt it is ABAB, and so forth, i.e., hep. Mainly on the basis of transmission electron microscopy techniques, there seems to be little doubt that the 0 — a transformation in cobalt involves a dislocation mechanism2 although its exact nature still remains obscure. Although the ß - a transformation in lanthanum is somewhat more complex than that occurring in cobalt, it was thought that its very uniqueness would be helpful in understanding fcc — hexagonal transformations in general. Such a general understanding of these transformations is important since they represent what are perhaps the simplest of the martensitic class of transformations. The experimental techniques used were those of electrical resistivity and transmission electron microscopy. EXPERIMENTAL PROCEDURE The lanthanum used in this investigation was prepared by the calcium reduction of lanthanum fluoride in a tantalum crucible under an argon atmosphere as described by Spedding et al. The residual calcium was removed by vacuum remelting in a tantalum container. Portions of the metal were then analyzed by emission spectroscopy as well as vacuum fusion. The amounts of the various impurities that were found are listed in Table I. A portion of the lanthanum ingot was swaged at room temperature into 0.030-in.-diam rod for the resistivity samples while the remainder was rolled into 0.010-in.-thick sheet for the transmission electron microscopy phase of this investigation. In order to eliminate the plastic deformation induced in the samples during fabrication, they were sealed in evacuated tantalum lined quartz capsules and annealed for 1 hr at 700° C. Specimen resistances were measured using the conventional "four-wire" technique described by MacDonald, 4 employing a type K-3 Universal Potentiometer and a standard 0.001-ohm resistor, both manufactured by Leeds and Northrup Co. By taking into account all of the possible errors in the apparatus, it was felt that the absolute resistivities of the approximately 0.87-in.-long specimens measured are reliable to 3 pct. Resistances from room temperature to 700°C were measured using a vacuum furnace. In order to avoid sample contamination by the thermocouple, chromel-alumel leads were spot-welded into a tantalum shield which in turn was welded to the lanthanum specimen. Resistances below room temperature were obtained by transferring the sample to a helium gas-filled quench tube and slowly dripping liquid nitrogen into a surrounding dewar flask. A steady reduction of temperature to about —190°C was completed in about 23 hr, and the resistances were measured at various temperature intervals. As will be shown shortly, rapid quenching from above about 350°C was sufficient to suppress the B -a transformation initially but subsequent annealing at lower temperatures leads to a partial ß --a conversion. To investigate this aspect of the transformation, the samples were suspended in the hot zone of a helium-filled furnace from which they could be rapidly dropped into the quench tube mentioned previously which was now

Jan 1, 1969

By Wayne P. Myers

Electricity, as normally thought of by a layman's definition, is a manmade force that has no color, no odor, is not visible, cannot be heard, yet man can control it and make it perform his work for him. A person dare not cheat on it, for it then will master him. It has laws, rules, and regulations that must be strictly adhered to if it is to perform in the safest, most reliable, and economical manner. In the early days of coal mining the power source was man himself. Later man employed steam and compressed air to reduce his muscle power requirements needed in the extraction of coal. By the turn of the 20th century, electricity had become the most common source of power for the coal industry. Steam and compressed air are still found in use in isolated cases today for specific applications; however, they are rapidly being replaced by electricity. Electrical laws and regulations are quite extensive and somewhat complex for the proper generation and use of electricity. Man-made laws, rules, and regulations for the care and handling of electricity, designed for man's safety, are rigidly enforced by the U.S. Bureau of Mines, as well as the various state departments of mines. BACKGROUND Until recent years most underground coal mines used direct current exclusively for all movable and for some stationary equipment. Exceptions were for permanent pumps, tipple, fan, and outside buildings where alternating current was normally employed. However, over 60 years ago there were mines with dual systems. Alternating current was used for cutting machines, drills, and pumps, direct current for locomotives. There were no other machines as these were hand-loading mines. Later, during early mechanization in the 1920s, alternating current was also applied to loading machines at some mines. Use of dual electric systems then declined until fairly recently when

Jan 1, 1973

By Eugene Guccione

It would be extremely difficult and unfair to compare the United States to Australia when wondering about which of the two countries offers the best opportunities for running a mining operation. However, if somebody would ask "Where is the best place to mine outside the US?"-I'd answer without reservations: Australia. Some of my Australian mining friends will disagree with me for my giving their country such a high rating. And they'll probably accuse me of being an optimist by telling me, as one of them did, that "the difference between an optimist and a pessimist is that the pessimist is better informed."

Jan 1, 1977

H. 0. Hofman, Boston, Mass. (communication to the Secretary*) :—The experimental demonstration by Professor H. Ries, of the fact that a mixture of clay and finely-ground flux will melt more readily than one in which the flux is less fine and therefore less intimately mixed, is very striking, and will be appreciated especially by those who have to discuss, before classes of students, fusions on a small or a large scale. The statement, that I " rather disputed" the influence of size of flux-particles on the ease with which fire-clay mixtures fused, is an erroneous inference from the paper written by Mr. B. Stoughton and myself in 1898.' We did not undertake to study the influence upon fusibility of the sizes of the particles, either of clay or flux. What we did try to find out was, whether the common practice of finely grinding raw or burnt clay, or a mixture of the two, before testing with Seger cones for resistance to heat and to fluxes, xould give the same results as if the materials were tested just as they were going to be

Jan 1, 1904

By John P. Hager, Igor A. Wilkomirsky

The thermodynamic properties of the Pb-Ag system have been determined between 775° and 950°C by the cell: Electrotransport measurements on silica-saturated PbO-SiO2 melts established that the conduction was entirely ionic and that lead is present only in the divalent state. The activities of lead and silver exhibit Positive deviations from ideal behavior. In dilute solutions the activities of lead and silver follow Henry's law. The values obtained for yhb and yig at 1200°K are 1.49 and 1.69, respectively. Determination of a portion of the liquidus curve agrees well with the established phase diagram. provides an accurate means for the thermodynamic study of liquid alloy systems. However, Wagner and wernerl have shown that cells of type I are limited to alloy systems for which the reaction at the alloy-electrolyte interface will be extremely small. The traditional electrolyte for cells of type I has been a low melting point mixture of group IA chlorides, to which a small amount of the compound ACIZa has been added. However, the choice of a chloride electrolyte may not always be practical, in that the Gibbs free energies of formation of the compounds ACIZ, and BCIZb may not be sufficiently different to minimize Reaction [I]. On the other hand, the Gibbs free energies of formation of the oxides of metals A and B may be sufficiently different to minimize Reaction [I]. In this case, the use of molten oxide electrolyte would be clearly advantageous. In the present study, the thermodynamic properties of the Pb-Ag system have been investigated using the cell: Previous galvanic cell studies on the Pb-Ag system2'= are not reliable due to the displacement reaction between the alloys and the chloride electrolyte. Wagner and ~erner,' using Laitinen and Liu's' value at 450°C for the standard electrode potential of Reaction 111, have estimated the percent error in the activity of lead bPb) when using a chloride electrolyte. At 1000°C the error for xpb = 0.10 is 12 pct. Taking the Gibbs free energies of formation for PbClz and Ag cI,' and the equations of Wagner and Werner,' the error in apb at 1000°C and Xpb =0.10 was calculated to be 140 pct. However, using the Gibbs free energies of formation for Pb O' and an estimated value for Ag 20, the error in apb when using a molten oxide electrolyte at 1000°C was estimated to be less than 1 pct for The virtual reaction of cell I1 for the passage of n Faradays of positive electricity from left to right in the cell is: where 5 is the Faraday equivalent (23,063 cal per v equivalent), E is the electromotive force of the cell in volts, and n is the number of Faradays of electricity required for the transfer of 1 g-atom of lead through the cell. The value of n should be equal to 2 since lead is generally divalent in oxide melts. However, the presence of either tetravalent lead ions or electronic conductivity through the molten oxide electrolyte will result in a value of n greater than 2. Bockris, Kitchener, and Davies' have determined the amount of ionic conductance in a liquid PbO-SiO2 mixture (xPbO= 0.50) at 920°C by measurement of the volumes of CO and C& evolved at a carbon anode during electrolysis. From their data a value of 2.13 * 0.16 was calculated for n. Although their measurements indicate the possible presence of multivalent lead ions and/or electronic conductivity, their measurements were not at silica saturation and no definite conclusions can be drawn. However, as a result of the electrotransport measurements described in the next section the ;due of n can be taken as equal to 2.

Jan 1, 1969

By B. Chalmers, L. Bäckerud

The growth temperature of dendrite tips has been measured in a binary alloy system, Al-Cu, as a function of rate of formation of solid phase. Metallographic examination has rerealed the dendritic structure dereloped during different stages of the freezing process and factors influencing the undercooling, such as solute buildup, surface tension, and kinetic effects, have been estimated. Practical implications of the results are discussed. THE development of a dendritic growth pattern during the solidification of metals and alloys has an influence at least equal to that of grain size on the properties of the casting or ingot being produced. and consequently much interest has been devoted to the study of this phenomenon. A review of the knowledge gathered up to 1964 has been given by Chalmers.' Among recent publications in the area the works of Jackson et al 2 and Flemings and his coworkers3,4 are of special interest. This work is an experimental study of the factors which influence the development of a dendritic pattern during the solidification of a typical binary alloy system, A1-Cu, when there is no heat source in the liquid. This means that the temperature and the temperature gradient are controlled by the heat extraction from and latent heat evolved by the growing crystals. EXPERIMENTAL PROCEDURE Samples were prepared from a master alloy made up of aluminum, 99.995 pct, and copper. 99.99 pct, of the concentrations given below and of sufficient size to fill cylindrical graphite molds of 35 mm ID and 35 mm height. Bottom. wall. and lid of the graphite molds were all of 6 mm thickness, Fig. 1. Thin ceramic thermocouple shields could be introduced at different positions in the sample through holes in the lid. The assembly was heated in a small vertical resistance furnace to a suitable temperature. 700° to 720°C. which is well above the melting point of the sample. It was thereafter taken out of the furnace and chilled at selected rates, and the temperature changes in the sample were recorded. For high sensitivity in the temperature recordings, a reference thermocouple was held in a solidifying pure aluminum melt. which was very well insulated and therefore was at a constant temperature. 660°C, for nearly half an hour. The thermocouples were connected so that the difference voltage was fed into the recorder of which the most sensitive range was 1 mV. Temperature variations could be read to within 0.l°C. The thermocouples used were of the Chromel-Alumel type (28- or 38-gage wires) and the recorder a two-pen Moseley strip chart recorder. The different rates of chilling were obtained in the following way. a) The graphite crucible was wrapped in one or two layers of an insulating. feltlike material (Fiberfrax paper from the Carborundum Co.). The drop in temperature per unit time after complete solidification could thereby be varied from 8" to 18°C per min. This corresponds to a rate of heat extraction in the given samples from 0.08 to 0.17 cal cm-' sec-I. 6) The bare graphite mold was placed free on a piece of firebrick. The measured temperature drop was around 50°C per min (-0.5 cal cm-" ' sec- I). c) By blowing compressed air through a tube with many holes surrounding the mold in a ring shape. the rate of heat transfer could be raised to 150' to 200°C per min (-1.7 cal cm-3 sec- I). d) Cooling rates around 1000 C per mill (-9.4 cal cm-3 sec-l) were obtained by substituting the air in the device used in c by water. The range of cooling rates used in these experiments correspond to technical casting processes from slow solidification as obtained in sand molds to very rapid freezing which occurs in some continuous casting and welding processes. EXPERIMENTAL RESULTS The A1-Cu system was chosen for the experiments: the relevant part of the phase diagram is reproduced in Fig. 2. Observation of the Center Temperature. When a thermocouple is inserted in the center of the melt. the type of cooling curves obtained at slow solidification rates differs little from numerous published curves from similar systems. and the solidification pattern

Jan 1, 1970

By Arthur L. Christenson, Clarence E. Jackson

IN the establishment of the relationship between weldability and hardenability, two methods have been employed in correcting for the grain growth produced in the heat-affected zone: first, the hardenability calculated from chemical composition1 may be corrected to the grain size observed in an actual weld,2 or, second, a hardenability test may be made on the steel quenched from a temperature high enough to produce a grain size comparable to that found in the heat-affected zone.3 In order to obtain grain sizes in the end-quench hardenability bar comparable to those resulting in the base metal from the welding cycle, a quenching temperature of 2100°F. has been used. In studies of the end-quench hardenability specimen quenched from 2100°F. instead of from a lower temperature of 1700°F., it is important to ascertain the relative cooling rates for various distances along the bar. It is a question as to whether the cooling occurs at the same rate or whether there is any significant difference from the standard cooling-rate curve published by Jominy and confirmed by others.4,5 This paper reports experimental evidence concerning the effect of quenching temperature on the cooling rates in the end-quench hardenability test. The effect of quenching temperatures on cooling rates has been studied by a number of investigators.6,7 French has considered this effect from both theoretical and experimental aspects. In French's studies on complete quenching of spheres and rounds, an increase in the quenching temperature caused an increase in the cooling rate at 720°C. at the center of the specimen. The center cooling velocity also has been shown to be dependent upon the surface per unit volume for the type of specimens studied; the velocity of cooling increases with an increase in the surface per unit volume. Three methods of indicating the rapidity of cooling of a body of metal during a quenching operation have been proposed: I. The time it takes for the metal to cool from the quenching temperature to a temperature halfway between the quenching. temperature and the temperature of the quenching medium (half-temperature time): Grossmann, Asimow and Urban7 justify the use of this criterion by the fact that the half-temperature time includes the temperature and time of incubation as well as the zone of formation of pearlite and, further, the data so derived accord very closely with experimental values. 2. The time interval the metal remains in a given temperature range; for example,

Jan 1, 1943

By C. A. Stetefeldt

In a former paper (Runs., xxi., 286) I described the plant of the Marsac Refinery, and the manipulations of the process, but cou1d not, at the time, give reliable statistical results. To supply the latter is the object of the present paper. I shall give actual facts as correctly as possible, without any bias one way or the other. For all statistics I am indebted to Mr. W. G. Lamb, who has charge of the Marsac lixiviation-plant and refinery; to Mr. A. Luebeck, assayer at the Ontario mill; and to the Daly Office, Salt Lake City.* Before starting on the work of the year 1892, a most careful clean-up was made, and any remnants were charged to the refinery. During 1892 the Marsac lixiviation-works produced 48.8 tons of so-called "regular" sulphides, which contained, on an average, 11,449 ounces of silver per ton; 11.77 ounces of gold per ton; and 569.8 pounds of copper per ton. To this must be added, 266 pounds of sulphides and by-products left over from the product of 1891, which contained 1380 ounces of silver, 1.41 ounces of gold, and 63 pounds of copper. Before giving the results of the clean-up, a general discussion of the items of expense, methods of assaying, etc., is desirable.

Jan 1, 1895

By H. C. Rolseth, J. J. Calaman

6.4-1. Principles of Operation. The jet-piercing process is a patented thermal process which depends upon a characteristic of the rock which is termed spallability. In its simplest terms, spalling is considered as decrepitation resulting from differential expansion of rock crystals due to thermally induced stresses. The number of individual properties influencing the spalling characteristics of rock are so numerous and their interaction so complex that the only truly reliable way to ascertain the spallability of rocks under thermal shock conditions is to expose them to these conditions. However, laboratory and field work have determined the principal thermal, physical, and mechanical properties of rock which affect spallability (10, 18). The approximate relationship between spallability and these characteristics is as follows: [ ] where To is the critical temperature at which, it is believed, a rock becomes elastic or sufficiently plastic to prevent further spalling action. Thermal diffusivity takes into account the amount of heat used in saturating the medium itself during the migration of a heat front. The rate and degree of dimensional changes which influence the spalling tendency of the rock will depend upon the characteristic of the heat gradient in the rock. The greater the spalling tendency, the higher the piercing rate. Those properties most favorable to a high degree of spallability are: 1. Large linear thermal expansion at temperatures below 700°C. 2. High thermal diffusivity at temperatures below 400°C. 3. Equigranular interlocking structure with little or no fine-grained clay or mica alteration products. 4. No significant amounts of soft, low-melting, or elastic mineral or materials which yield after thermal decomposition.

Jan 1, 1968

By Frederick G. Clapp

SINCE oil journals commenced to feature the progress of Iraq pipe-line developments and since newspapers undertook to follow the discussions between a certain large oil company and an Asiatic nation, I have repeatedly been asked questions that are only answerable by setting forth the essential geographic and historical facts of concessions in that part of the world. In so doing effort will be made to correct erroneous statements made in various quarters: and mistakes herein are being kept as low in number as possible. Perhaps the best-known concession in the Middle East is the one of the Iraq Petroleum Co., covering the greater part of the portion of the kingdom of that name- lying east of the Tigris River. West of the stream is the concession of the British Oil Development Co., which takes in all presumed petroliferous areas in western Iraq. No other important oil concessions exist in that country, except for the lands of the Khanikin Oil Co., which operates in "Transferred Territories" on the border of Persia. East of and continuous with the Iraq fields are those of Persia where the Anglo-Persian Oil Co. holds the well-known D'Arcy concession comprising three-quarters of the country, omitting the five northern provinces. This is the only valid existing concession in Persia, so far as known, except certain old firmans that permit development at Semnan in central Persia and possibly also certain regional grants to a French banking syndicate in eastern Mazanderan Province.

Jan 1, 1933

By James C. Bayles

The ideal pressure-tube is obviously the one which combines the greatest strength with the least weight of material consistent with the uses for which it is designed or employed. The inside of the pipe is the first concern of the engineer. It should be cylindrical, smooth, and of the requisite capacity for the purpose in view. It should be in lengths as great as can be oonveniently handled, so that the couplings may be as few as possible. With the walls of the tube the engineer has no further occasion to concern himself than to make sure they are adequate to carry the internal and external pressures to which they will be subjected. It is as true of a pipe as of a truss, that when it is strong enough to give the requisite factor of safety, nothing is gained by having it stronger. Anything more than this means dead weight, which has to be paid for many times, first as material, and again and again in the costs of transportation and handling, until it reaches its place in the trench or on supports. In use it must be and remain tight against all leakage, and must sustain whatever is placed over or upon it, or suspended from it, without deformation or injury. Finally, in addition to meeting all the immediate requirements of service, it must possess qualities of durability which warrant a reasonable expectation of a long life of usefulness. The wise engineer no longer regards it as reasonable to depend upon mere bulk of its own material for the protection of a metal as readily impaired or destroyed by oxidation as iron or steel. The metal must have a coating which will be and remain impervious and indestructible. When all these conditions are met, we have as near an approach to the ideal tube as can be attained with the materials now available for their manufacture. Steel wed constructively, to the best advantage, meets these requirements most perfectly. Gold alone would do it better. If we search through the whole list of metals and alloys we find nothing available which so perfectly meets the requirements as a pipe material as steel. Mr. Hamilton Smith, Jr., in a paper on the expedients adopted on

Jan 1, 1891

By Charles F. Brush

The compression of gases to a very high degree, for purposes of scientific research, has long presented serious difficulties to the physicist. Great advances have been made of late years in the construction of ordinary air or exhaust pumps, while very little has been done towards the improvement of compression pumps. The principal difficulties encountered in the construction of such apparatus are the existence of the so-called "dead space" in the pump barrels, leakage of the piston packings under high pressure, and the trouble arising from the unequal expansion of parts caused by the development of the latent heat of the gas during compression. Of these obstacles to success, the "dead space" is far the most serious, as it fixes a limit to the performance of the pump beyond which it is impossible to carry the compression. The writer having occasion, some time since, to make a series of investigations on gases very highly compressed, and finding no apparatus, or description of apparatus, adequate to produce the required

By A. L. Labbe

SOON after the Cottrell treater was placed in operation in the Murray plant in 1918 to treat combined lead sinter and Wedge roaster smoke, it was noticed that the power flowing through the treater did not remain constant. This was indicated by the varying milliamperes and also by the total amount of power consumed by the rectifiers. At times, for then unknown reasons, the treater current fluctuated through a wide range of from 40 to 300 milliamperes. Fortunately, these variations in power did not affect the treater's overall recovery, as this installation consisted of three independent units in series, a feature which made the Murray Cottrell an outstanding installation over many years of operation. Water conditioning of the smoke as a means of improving recovery was already known, but was not adaptable to this installation for reasons of excessive corrosion, which had been the case with other treaters using water as a conditioner exclusively. Tests conducted on the smoke had proved conclusively that water vapor played no part in the fluctuation of power, and the same was true of the SO2 contents and dust burden of the smoke. Neither did temperature variations of from 150 to 400°F have any effect on the power. Finally it was noticed that the variation in power taken by the treater, and the efficiency of recovery, had some definite relation to the number of Wedge roasters operating, and particularly to the sulphur contents of the charge. This observation soon led to the discovery that free sulphuric acid was the conditioner for Murray smoke and that variations in acid contents of smoke accounted for fluctuations of treater power. Analysis of recovered dust revealed that only a few hundredths of a per cent free acid was necessary to maintain a very efficient recovery. Once this knowledge was available, the roaster charge was adjusted as to sulphur contents to produce the necessary acid conditioner. For a number of years this practice was followed, but with improvements in the field of flotation, excess pyrites were eliminated from the smelting picture, so with a change in metallurgical practice we were confronted with the problem of providing the deficiency in acid by some other means. The situation was aggravated and our problem of acid conditioning made more difficult by the increase in the lead contents of concentrates roasted resulting from better flotation methods. The first step towards introducing acid vapors into the smoke stream by accessory means was accomplished by boiling sulphuric acid in cast iron pots placed in an open fire box. Acid fumes evaporated from the pots together with the combustion gases from the fire box were discharged into the flue through a cast iron pipe. Capacity of the iron pots was quite limited because of the comparatively slow rate of evaporation and the use of lump coal as a fuel, which did not lend itself to practical temperature control. This method of firing resulted in frequent pot failures due to overheating. In spite of these incidental difficulties, encountered in any new venture, the pot evaporator demonstrated the practicability of fuming sufficient acid to make up the deficiency in that naturally evolved in the Wedge furnace operation. As time progressed, less and less high sulphur material was available for Wedge roasting, and the necessity for accessory acid conditioning reached a climax when the supply of this material was entirely eliminated. Since the cast iron pots could only evaporate a few hundred pounds of acid per day, and were costly to replace, the logical thought presented itself of spraying the acid in a heated chamber. This new type of acid evaporator was simpler and more economical to operate and had sufficient capacity to fume several thousand pounds per day. The attached fig. 1 presents the outstanding features of the new furnace. A is the vaporizing drum, which is heated by the combustion gases of coal stoker fire box, B. Acid is sprayed into the hot gas stream within the drum through a number of air-acid atomizers, C, and the acid vapor, together with combustion gases, is introduced into the smoke stream through two cast iron pipes extending to different points in the flue. The operation of this type of furnace requires control of temperature inside the drum to prevent overheating, which dissociates the acid vapor to SO, and eventually to SO2, with resulting loss of acid. The dissociation to SO, at elevated temperatures is comparatively high, and in some cases accounts for as much as 60 pct of the acid sprayed into the drum. To reduce the loss of acid, through dissociation, some Cottrell plants, where the rate of acid sprayed reaches at times 9 ppm, use two evaporating units. Fuming the acid into the smoke stream is only

Jan 1, 1951