Search Documents

By Marius S. Darrow, William B. White, Rustum Roy

The PbS-PbTe systen has been studied by quench-ing and D.T.A. techniques f?om 400' to 1150°C. Runs were made in evacuated silica tubes so that all equilibria are at the vapor pressure of the system. Lattice parameters of the quenched salnples , measured by X-ray diffraction, show a complete crystalline-solution series existing over a narrow temperature range between approximately 805" and 871°C. An exsolution dome extends from a maximum of about 805"C (approximately 30 mole pct PbTe) to 1 and 96.5 pet PbTe at 400°C. A narrow melting region, deternined by D.T.A., extends form 918c (mp PbTe), The shapes of the liquides and solidus curves imply the existence of a minimum at 871°C at approximately 65 pct PbTe. THe exact composition of the minimum could not be established due to the very narrow two-phase region. At compositions containing less than 50 pet PbTe, liquidus temperatures begin to increase, while the solidus remains almost flat to about 15 mole pet PbTe before beginning to vise toward the mp of PbS (1075 C). LEAD sulfide and lead telluride are isostructural (NaC1 type) semiconductors whose electrical and optical properties have been extensively studied and used in recent years. If appreciable crystalline solution exists between these compounds, the variation of physical properties with composition could be of interest. The purpose of this investigation was to determine the extent, if any. of crystalline solution, and to obtain the phase diagram for the system. To the knowledge of the authors, only three studies of the system PbS-PbTe have been reported, and, in chronological order, each investigation found an increasing amount of crystalline solution. In 1956, Yamamoto reported finding no evidence of crystalline solution between the compounds. Sindeyeva and Godov-ikov,' in 1959, found very limited crystalline solution. but only under conditions of excess tellurium concentration. Finally Melevski s3 investigation in 1963 indicated that one solid phase exists in the region from PbS to 7 pct PbTe and from 82 pct PbTe to PbTe at 886'C, with an eutectic at 55 pct PbTe at that temperature. Detailed data on the solvus boundary were not given. EXPERIMENTAL EQUIPMENT AND MATERIALS Commercially produced PbTe and PbS powders were used as starting materials. Batches of specific mole percent composition were accurately weighed and mixed in a plastic bottle, in a shaker mill. An analy- sis of impurity content is given in Table I for pure PbS and PbTe and for two randomly selected batches after the powders were mixed. Individual samples, ranging in weight from 0.2 to 0.5 g, were sealed in evacuated silica tubes which had been thoroughly washed and rinsed with acetone and distilled water. Thus all data taken were at the pressure of the system. Subsolidus relations were studied down to 400°C by heating the samples in a vertical tube furnace for 24 hr. The sealed tubes were quenched in water with quench time from the hot zone not exceeding 1 sec. Temperatures were measured by a chromel-alumel thermocouple and controlled to 53°C for most runs. The number and composition of phases present were determined from powder X-ray diffraction patterns taken at room temperature on a Norelco diffractome-ter, using silicon as an external standard. Above 850°C quenching techniques were, in general, found to be unsatisfactory, and differential thermal analysis (D.T.A.) was used to determine melting relations. The evacuated tubes were recessed about 1 cm at one end to accommodate the differential thermocouple. Al203 was used as the reference material in a similar tube containing the other side of the differential couple. For temperature measurements, a separate thermocouple was placed in the recess of the tube containing the sample to be measured, thus providing an opportunity to obtain thermal, as well as differential, analysis. All thermocouples for these measurements were Pt-Pt 10 pct Rh. Temperature and differential curves were recorded separately on synchronized strip-chart recorders. Thermocouples and recording equipment were calibrated using NaCl and gold standards, using the melting points 801" and 1063 C, respectively, which span most of the temperature range of interest. Heating and cooling rates generally were from 4 to 7°C per min. It was found, in fact. that rates ranging from 1.5 to 25°C per min did not significantly change the data obtained.

Jan 1, 1967

By C. J. Ramsburg

THE construction and operation of by-product coke-oven plants in America are essential to strong national defense and of the greatest importance to many widely diversified undertakings as well as to safety and health. CARBONIZATION PROCESS Coal used under a boiler or in a locomotive is consumed by combustion. Coal used in a by-product oven is distilled or carbonized, meaning that heat is applied to the coal, out of contact with air, causing a distillation that removes the volatile matter in the coal in the form of gas and vapor, leaving coke as a final product. From the gas and vapor distilled from the coal, many valuable substances can be secured, known as by-products. Hence the name "by-product oven." The simplest example of this principle can be shown by means of an ordinary clay pipe. If powdered coal is placed in the bowl of the pipe, the opening of the bowl is plugged with clay, and the bowl placed in a flame, the bowl will become hot, transferring the heat through the wall of the bowl to the coal within. When this coal attains a temperature of about 950°F., gas will begin to pour out of the pipe stem, and this gas may be lighted. A black liquid also will exude from the stem of the pipe. This is tar mixed with certain other products. What remains in the bowl after distillation is coke. A coke oven corresponds to the bowl of the pipe. A modern oven of the latest type is a refractory brick chamber approximately 42 ft. long and 14 ft. high, averaging 18 in. in width. The oven is filled with coal through closable charging holes in the oven top. Each end of the oven consists entirely of a self-sealing door, the removal of which permits the finished coke to be discharged by means of a power-operated pusher machine. The ovens are built in batteries, and the heating is effected by gas burned in vertical flues in the oven walls, each set of flues heating the walls of two adjacent ovens. Such ovens carbonize a charge of approximately 18 tons of coal in 18 hr., or have a daily throughput of 24 tons per oven, producing about I 7 tons of coke. In times of need, the output may be increased by raising the temperature of flues, thus shortening the coking time. There is one great essential difference in principle between distillation in a clay pipe and in a coke oven. In the 18-in. oven, the distillation proceeds from two parallel walls held at a high temperature (over 2000°F.) and instead of all the coal being heated at once, the distillation is a progressive one creeping inward. The average travel of this heating is 1/2 in. per hour from each vertical wall, and as the volatile products are formed progressively they must push away from the interior toward the wall through the previously formed hot coke, then up the walls and over the top of the coal charge, finally escaping through the outlet pipe. This results in a cracking of the components into many different and valuable substances not formed when the carbonizing temperature is low.

Jan 1, 1942

By P. D. I. Honeyman

CHANGING trends in concentration, involving regrinding with the subsequent production of a finely divided, high-grade flotation product, presents a real problem to the modern copper smelter. In the treatment of such a material, handling difficulties are numerous and potential possible losses may be very great. In many plants, of course, preliminary roasting of the furnace charge remains an economical necessity. Under such circumstances, the operator has no alternative except to follow orthodox roaster reverberatory practice, though taking all possible precautions to avoid excessive dust losses and bad working conditions. In other plants, roasting is not only unnecessary but would be highly undesirable, and at best the charge would be merely dried before entering the reverberatory furnace. In the latter case the possibilities of raw charging loom large. The Miami plant of the International Smelting Co. handles the entire output of concentrates of the several mining companies operating in the Globe-Miami district. All of these companies produce a flotation concentrate which, at the Miami Copper Co. particularly, is all reground and is high in grade. In addition, the Inspiration Copper Co. ships a substantial tonnage of high-grade cement copper to the smelter from its leaching plant. Following the flow sheet of the original plant, all such material received was bedded, dried in Wedge furnaces and smelted in reverberatory furnaces. At times during the history of the plant it has been necessary to carry the drying operation further, to a partial roast, before reverberatory smelting. Since the charge contained over 80 per cent flotation concentrates, the handling of which in a dried condition was at best a dusty job, unusual precautions were taken to cut down dust losses. The Wedge furnace plant was equipped with a Cottrell treater and all hoppers and calcine cars were carefully designed to cut down dust loss in transferring the so-called calcine from hoppers to car and from car to furnace. In the furnace itself the dusting problem was a severe one. Arch erosion was very rapid and flues and waste-heat boilers rapidly filled up with a partly smelted flue dust.

Jan 1, 1932

By O. A. E. Jackson

Pebble milling has been practiced in the reduction works of South Africa gold mines for well over 50 years. Originally flint pebbles were imported from Denmark to grind stamp-mill amalgamation-process tailing, which contained a good deal of extractable gold, but local operators soon found that large pieces of ore could be used for the same purpose. The ore is a hard, tough conglomerate in which quartz pebbles are cemented together by a matrix of redeposited silica interspersed with pyrite crystals. The gold, rarely visible, occurs as fine particles mostly segregated at the interface of the pebble and matrix, although a small fraction occurs within the pyrite crystals. There is seldom any gold in the pebbles themselves. Following the usual South African practice in pebble milling, Union Corp. grinds the ore wet in two or three milling stages incorporating classification. The sized broken ore used as grinding media is separated from the main ore stream in the crushing section that prepares the ore for milling. Where the ore channel, or reef, is narrow there is a shortage of large pebbles. In this case primary grinding may be done in ball mills or, more recently, in rod mills, which cost less per ton to operate. The trend, however, is to prepare finer feed for the milling section. This makes it possible to use smaller primary pebbles and eliminates the need for steel. REDUCTION WORKS OF UNION CORP. LTD. Union Corp. Ltd. exercises financial and technical control over a group of seven gold mines in the Transvaal and Orange Free State. In the Transvaal, with one exception. the mines lie 20 to 40 miles east of Johannesburg, in flat or gently rolling countryside. Winkelhaak, the first of several new mines that will be developed by Union Corp., is located in similar terrain in an entirely new gold mining district about 80 miles east of Johannesburg. Table I gives details of milling units for six of the Union Corp. mines, together with the tonnage milled in 1957. Winkelhaak Mines Ltd. is not included, as it did not begin milling until 1958. This reduction plant has no crushing section; ore is ground directly from the mine (autogenously) in 12x16-ft mills. Because these operations are still in development, they are not described in this article. It will be noted that certain reduction works have mills of more than one size in the same milling stage. This came about when plant extensions in- corporated larger units. In the case of Geduld Propty. Mines Ltd., which began milling operations 50 years ago, the primary stage is stamp milling. The reduction works follow a uniform pattern and are usually joined to the main ore shaft. Ore from other shafts is brought by standard-gage railway and dumped into a common transfer bin. The trend is to increase surface storage capacity to enable the crushing and milling sections to operate at a steady rate, independent of fluctuating ore deliveries from mine. Milling and cyanide extraction divisions of new mines are always designed to allow for extensions as mine production increases. The conveying, washing, and screening system of the crushing section is usually laid out in final form, with additional space for more crushing equipment. The crushing sections operate on one shift during early years of mine production; a second shift is introduced when the mining rate warrants it. Ample surge capacity is provided. Crushing and milling is done only on weekdays, as the law does not allow these operations to take place on Sunday in any plants constructed since 1911. The cyanide extraction sections, however, operate continuously seven days a week, drawing on mill pulp gradually built up in the thickeners during the week. Construction and equipment of milling plants follow standard practice. Dilution water is drawn from a large, high-level tank to obtain constant pressure, but gland service water for the pulp pumps is reticulated from high-pressure, two-stage pumps. The mills are equipped with the most up-to-date machinery and are designed to save labor. They compare favorably with milling plants in countries where native labor does not exist, and automatic controls are being installed wherever feasible. Hydrocyclone classifiers have replaced mechanical classifiers in modern milling plants, chiefly because of the saving in capital outlay, maintenance, and building space. The hydroclones are fed from steady head boxes rather than directly from pumps, and dilution water is introduced into these boxes. Tests have shown that in steadiness of operation and separating efficiency cyclones are comparable to mechanical classifiers. but protective stationarv screens are needed to keep the spigots clear. Rubber-lined pumps are used for pulp of about 3 mesh or finer and metal-lined pumps for coarser material. None of the Union Corp. milling plants practices gravity concentration of coarse gold by amalgamation or the use of corduroy blankets. Studies have proved that no economic case can be made for these methods, which complicate the milling process and demand extra precautions against theft.

Jan 1, 1960

By J. A. Bowers

THIS investigation of the effect of bottom shape and life on slag volume was carried out in two Lectromelt top-charge furnaces whose rated capacity is 1000 lb per hour. Unfortunately, just as the work [ ] was started, our steel tonnage was reduced approximately one half, therefore we did not accumulate enough data from which to draw any definite conclusions. Furthermore, the life of the linings in these furnaces was greatly decreased by intermittent operation, which was a further handicap in making a study of this kind. The weight of the heats from which the data were taken varied 1200 lb but all the information was corrected to the standard weight charge for these furnaces of 4500 lb. Almost all the heats were plain carbon; a few contained a small percentage of added copper.

Jan 1, 1947

By C. W. Crispell

THE four nomograms presented in this article were designed to simplify and make more, rapid the calculations connected with the compression and transmission of air. The formulae involved are rather complicated, but the graphic solutions are simple; their use requires an ability to follow explicit directions and to interpolate values on a logarithmic scale. ? For the sake of convenience, the nomograms will be divided into two classes, and the purpose and accuracy of each will be discussed. Compression It is frequently desirable to determine the horsepower necessary to compress a given amount of free air from atmospheric pressure to a certain final pressure. The nomograms in Figs. 1 and 2 present a rapid method of calculating the horsepower required to compress 1 cu. ft. of free air per minute by single or two-stage compression. The general formula for the horsepower required to compress air adiabatically is: HP = S X 144/33,000 PVn/(n-1) [(P'/P) n-1/Sn -1] (1) where: P = absolute atmospheric pressure at compressor, in pounds per square inch. P' = final absolute pressure of compressed air, in pounds per square inch. V = volume of free air compressed per minute, in cubic feet. S = number of stages. n = exponent of the compression curve.

Jan 6, 1917

By Raymond M. Howe

Some time ago, a prominent engineer asked a representative of the firebrick industry to prepare a comprehensive paper on blast-furnace refractories. It was to have been the purpose of this paper to gather practical experiences from widely different sources, in the hope of determining what kind or kinds of firebrick were best adapted for certain uses. This engineer sent questionnaires to the large consumers of blast-furrace linings and stovebrick and received very detailed replies as to their experiences. These replies are conflicting, but, having been turned over to the writer, form the basis of this attempt to meet the request. Because of the impossibility of making final recommendations at this time, a few of the more interesting and commonly known methods of studying refractories are also discussed, as well as the more recent developments in this field. The first reply to the questionnaire stated that good service was being secured from the linings. This satisfactory condition was attributed to the use of a very good distributor. The writer believed that manufacturers try to and do produce a good product and that the proper handling of equipment is of the utmost importance, if good results are to be secured. The type of bricks used was not mentioned. The second reply stated that good life was secured from the furnace linings, but that the writer had had soft-fired stovebrick crumble and, for that reason, preferred a hard-fired product for use in this position. The type of bricks used was not mentioned. The third reply stated that firebrick had crumbled from the mantle up; the cause was not known. The fourth reply stated that the stove linings were satisfactory. Hand-made furnace linings failed after.4 years' service so a steam-pressed lining- was installed which was still good after 4 years of service. Consequently, a second steam-pressed lining was installed but this disintegrated at the top after the furnace had been in blast 7 months. The firebrick manufacturer attributed this failure to the expansion of iron blocks that had been installed at the stock line to prevent erosion. The fifth reply stated that the present "hard-burned" hand-made furnace lining had worn away very uniformly to the depth of only 5 in.

Jan 1, 1920

By F. E. Bash

A GREAT many industrial operations require the application of heat to carry on or complete processes, in which cases the temperatures must often be controlled within very narrow limits. For the lower temperatures, this control is not, as a rule, difficult as a number of types of reliable pyrometers are available for the work; for example, the mercury and resistance thermometers and the thermocouple. For temperatures above a red heat, thermocouples, platinum resistance thermometers, and total radiation and optical pyrometers may be used, depending on conditions. It is often undesirable, and sometimes impossible, to take temperatures of material by immersing the pyrometer in it or by placing the temperature-measuring device in a position in which it will attain the temperature of the material. The pyrometer may contaminate the product; the temperature may be so high that the pyrometer will not hold its calibration, clue to ineffectual protection and consequent contamination; the object may be inaccessible, as a lamp filament, etc. In such cases, a total radiation or optical pyrometer must be used. The disappearing-filament, or Morse, type of optical pyrometer works on the following principle: An objective lens, Fig. 1, focuses the image of the object whose temperature is desired in the plane of the lamp filament at F, which is at the principal focus of the ocular lens shown in the eye-piece. By this arrangement the eye will not have to accommodate itself first to the lamp filament and then to the object at a distance, and the lamp filament will appear superposed on the object. To balance the instrument, the current is adjusted by means of a rheostat until the tip of the lamp filament just disappears against the object as a background. Figs. 2, 3, and 4 show the appearance of the filament when too cold, too bright, and just balanced.

Jan 8, 1919

By Shiou-Chuan Sun

THIS paper presents the design and operation of a frothmeter capable of measuring the frothing characteristics of pine oils and other frothing reagents. The experimental data show that the frothability of pine oil is governed by: 1-rate of aeration, 2-time of aeration, 3-height of liquid column, 4-chemical composition of pine oil, 5-pH value of solution, 6-temperature of, solution, and 7-concentration of pine oil in solution. The effect of mineral particles on the behavior of froth also was studied, and the results can be found in a separate paper.1 The results also show that the relative frothabilities of pine oils in the frothmeter generally correlate with those in actual flotation, provided that other factors are kept constant. In addition to pine oils, the other well-established flotation frothers were tested, and the results are included. In this paper, compressed air frothing is the frothing process performed by means of purified compressed air, whereas sucked air frothing is the frothing process accomplished by purified air sucked into the glass cylinder by a vacuum system. The term vacuum frothing denotes that froth was formed by degassing of the air-saturated liquid under a closed vacuum system. Apparatus The frothmeter, shown in Fig. 1, is capable of reproducibly measuring the volume and persistence of froth as well as the volume of air bubbles entrapped in the liquid and is capable of being used for compressed air frothing, sucked air frothing, and vacuum frothing. Fig. la shows that for compressed air frothing, the apparatus consists of an airflow regulating system, 1-3; a purifying and drying system, 4-8; a standardized flowmeter to measure the rate of airflow from zero to 500 cc per sec, 9; and a graduated glass cylinder, 13; equipped with an air regulating stopcock, 10; an air chamber, 11; and a fritted glass disk to produce froth, 12. The fritted glass disk, 5 cm in diam and 0.3 cm thick, has an average pore diameter of 85 to 145 microns. The pyrex glass cylinder has a uniform ID of 5.588 cm and an effective height of 63 cm. The inside cross-sectional area of the glass cylinder was calculated to be 24.53 sq cm, or 3.8 sq in. For sucked air frothing, Fig. lb shows that the apparatus for compressed air frothing is used again, with the following modifications: 1-compressed air and its regulating system, 1-3, are eliminated; and 2-a vacuum system, 16, equipped with a vapor trap, 15, and a vacuum manometer, 17, is added. The vacuum system can be .either a water aspirator or a laboratory vacuum pump. Any desired rate of airflow can be drawn into the glass cylinder, 13, by adjusting the opening of the air regulating stopcock, 10. The sucked air stream is cleaned by the purifing and drying system, 4-8, before entering the glass cylinder, 13. When this setup is used for vacuum frothing, the air regulating stopcock is closed. The frothmeter has been used for almost 3 years and has proved to give reproducible results, as illustrated in Table I. With a magnifying glass and suitable illumination, the frothmeter also can be used to study the attachment of air bubbles to coarse mineral particles.2 Experimental Procedures Except where otherwise stated, the data presented were established by means of the compressed air method. The volume and persistence of froth were recorded respectively at the end of 4 and 6 min of aeration at a constant rate of airflow of 29.3 cc per sec which is equivalent to 71.6 cc per sq cm per min, or 462.6 cc per sq in. per min. The aqueous solution for each test, containing 1000 cc of distilled water and 19.2 ± 0.5 mg frothing reagent, was adjusted to a pH of 6.9 ± 0.2. The volume of froth is expressed as cubic centimeter per square centimeter and is equivalent to the height of the froth column (the distance between the bottom and the meniscus of the froth). The volume of froth was obtained by multiplying the height of froth by the cross-sectional area of the glass cylinder, 24.53 sq cm. Before each test, the glass cylinder, 13, was cleaned thoroughly with jets of tap water, ethyl alcohol, tap water, cleaning solution, tap water, and finally distilled water. The cylinder with stopcock,

Jan 1, 1952

By Armand Bur, W. R. Reichenstein

Since coal is one of the largest cost items in the production of electricity, its analysis for heat value and composition has been the subject of intensive study. Sampling started with crude hand methods, out of the railroad car or barge or from moving conveyor discharge, and progressed to reliable mechanical in-plant sampling systems. The mechanical system takes its sample from a falling stream of coal such as a conveyor discharge or crusher discharge hopper. But this has a disadvantage in that the identity of the coal is lost. Coal is shipped to the user in train-loads, often made up of shipments from various mines. When the cars are dumped into hoppers and the coal conveyed to the power station, the various shipments become mixed because residual coal remains in hoppers and chutes.

Jan 5, 1959

By R. M. Board

This paper will focus on measurement and control of four main aspects of crushing, namely horsepower, bowl level, mantle position and feed rate, and will discuss related sensors and control techniques, some of them designed specifically for crusher control, that have proven successful and reliable in many installations.

Jan 1, 1982

By AIME AIME

THE program of government drilling, conducted jointly by the U. S. Geological Survey and the Bureau of Mines, has demonstrated the presence in Texas and New Mexico of potash-bearing beds of considerable importance. Information regarding the ex- tent and location of the potash deposits as presented at the non-metallic sessions was of great interest to many engineers. These subjects will be covered in greater detail in later paragraphs. The first session, with about 50 in attendance, convened at 10 a.m. on Feb. 18, with Oliver Bowles, chair- man of the Committee on Non-Metallic Minerals, pre- siding. The first paper was on "Soapstone Mining In Virginia," presented by C. W. Ryan of Lynchburg, Va. The nature and extent of the soapstone deposits of Nelson County were described in some detail. In origin, the soapstone is undoubtedly related to a basic peridotite rock though its mode of formation is some- what uncertain. This main soapstone deposit occurs in three veins, the western, middle, and eastern, the middle vein being of greatest economic importance. Methods of stripping, quarrying and milling the rock were described and the uses of soapstone were enum- erated. In discussing this paper, C. P. Berkey, of Co- lumbia University strongly favored the theory of igneous origin of the soapstone and the need for further detailed geological study. J. L. Gillson of Cambridge, Mass., stated that the Vermont and New York talc deposits were always associated with characteristic minerals, such as, a chlorite of one particular variety, siderite, amphibole, magnetite, and biotite. C. H. Behre of Cincinnati, Ohio, raised the question of parallelism in the soapstone structure and Mr. Ryan stated that such parallelism was in evidence in some parts of the deposits. H. A. Wheeler of St. Louis, Mo., also took 'part in the discussion.

Jan 1, 1929

By H. T. Green, R. M. Brick

True stress-strain data on alloys of pure iron with up to 2.4 pct Al were obtained in the temperature range +100° to —185°C. Alumi-num was found to reduce yield and flow stresses of iron at low temperatures but to have little or no effect on ductility. The effects of temperature and composition on strain hardening are discussed. SEVERAL independent studies of the behavior of high purity iron binary alloys at low temperatures are now in progress in attempts to evaluate systematically the variables affecting the low temperature brittleness of ferritic steels. This paper reports the results of one such investigation in which the tensile properties of aluminum and aluminum plus silicon ferrites were measured from 100" to —192°C. True stress-natural strain data have been obtained in order to evaluate as many as possible of the parameters which describe the behavior of the materials involved. In comparable studies at the National Physical Laboratory in England, iron and iron alloys of high purity have been produced' and tested at subat-mospheric temperatures.' True stress-natural strain curves were obtained there also. The purest iron contained 0.0025 pct C and 0.001 pct O and N. Even this, as normalized at 950°C following hot rolling, showed little ductility at -196°C. The grain size was ASTM No. 3, and the room-temperature yield strength was 17,800 psi (which seems too high for pure iron). Some of the NPL irons contained considerably more oxygen and demonstrated intergran-ular fracture at —196°C. The authors2 carefully differentiated between intergranular fractures associated with excessive oxygen content and transcrys-talline cleavage with little ductility encountered at —196°C in the purer material. The cleavage stress was half again as great as that associated with inter-granular fracture. Test Material, Preparation, and Procedures Of a number of Fe-A1 alloys produced, eight were considered to be sufficiently pure for testing. Partial chemical analyses (Table I), low observed yield points, and high ductilities indicate these alloys to be comparatively pure for vacuum-melted irons of sizable ingots, 5 Ib or more. To produce the binary Fe-A1 alloys, electrolytic iron was melted in air, cast into slabs, and rolled to strips 0.010 in. thick. These strips, joined into a continuous ribbon and wound into 2 1/2 in. diameter spools, were subjected for four weeks to a moving atmosphere of purified dry hydrogen in a stainless-steel tube at 1050" to 1150°C. Charges of these spools were melted in beryllia crucibles under good vacuums (1 micron), and aluminum (99.97 pct Al) was added to the melts. Compositions of these alloys are recorded in Table I. The ingots were hot forged and then cold rolled at least 65 pct to 3/8 in. rods which were vacuum annealed to the desired grain size, approximately ASTM No. 4, prior to machining into tensile test bars. All tensile specimens had gage sections 1 in. long, with a fillet of 1.5 in. radius to the shoulder. Gage diameters were 0.250 in, except for a few rods where additional cold work required use of a 0.200 in. gage section. After machining, 0.002 in. was removed from the gage diameter using 240, 400, and 600-grit metallo-graphic papers. The final polish with 600 grit left the fine scratches running in the longitudinal direction. By this means, surface metal strained during machining was removed. A few specimens heat treated after machining were similarly reduced 0.004 in. to remove any material affected chemically by the atmosphere during heat treatments, as is discussed in a later section. Tensile tests of the eight alloys at constant temperatures from +100° to —185°C were performed in apparatus which has been described." The essentials include a double-walled insulated metal vessel which contained the liquid heat-transfer medium surrounding the test specimen. A constant temperature was maintained by means of a pyrometer which regulated the pressure of dry air driving liquid air through a copper coil. Temperature variation was less than ±2°C during a specific test. For axial straining, two lengths of case-hardened chain, terminating in simple shackles, loaded the specimen through threaded grips. The lower grip bar passed through a hole in the bottom of the test vessel to which it was joined by a thin-walled

Jan 1, 1955

By A. S. Richardson

THE rating of a mine ventilation fan, or the characteristic curves illustrating the duty it may be expected to perform under various mine conditions are, in general, determined by the fan manufacturers. The information is of importance to the operator, or engineer, of a mine in many ways. For instance, when an increased flow of air is desired and the fan speed is to be increased, it becomes necessary to know what increase in volume may be expected and what the power requirements will be. In other cases, it may be decided to make changes in the mine to reduce the resistance to the flow of air, or to make changes in the general system of ventilation. Under any changed mine conditions there will be a difference in the duty performed by the fan. When mechanical ventilation is adopted, the factors governing the selection of equipment for the new system include not only the requirements of existing conditions, but also those that may be expected with the development of the property. Efficiency of service is required over a variable range of operating conditions. Characteristic curves, giving the duty performed by their fans under variable resistance conditions, are published by most fan manufacturers. General statements as to the effect of variation in speed of the centrifugal-type fan, under fixed mine conditions, appear in textbooks and trade catalogs. However, to the author both sources of information appear to be unreliable, at least under certain circumstances. The catalog of a leading fan manufacturer says: 1. The volume of air delivered by a fan varies directly as the speed. 2. The pressure, or water gage, produced by a fan varies as the square of the fan speed. 3. The horsepower of a fan varies as the cube of the fan speed. While these statements are accurate when the fan is operating under conditions similar to those that exist when a blower is used to force air through a pipe, they are not correct under mine conditions that are by no means unusual. Such conditions may be found in deep mines operated through shafts, in which a wide range of temperatures may be

Jan 8, 1925

By Charles W. DeWitt

The ore treated at the reduction plant (called Yangdei) of the Chiksan Mining Co., Korea, is brought from four of the company mines, and from the small tribute mines. The largest shipments come from Sajunkohl mine, situated about a mile and a half from the mill (Fig. 1). The ore is quartz of medium hardness. The average assay value in gold is $6.95 per ton. At the mine the ore is put into bins, and is then trammed over an 8 per cent, grade to the tipple bins above the mill, where the ore is drawn through the mill holes as desired. The capacity of the tipple bins is about 3,500 tons. Ore from Moonsukohl, Chung Tarrie, Yang Chun, and the tribute mines is brought in by bulls and bull wagons. The bulls carry from 350 to 800 lb.; the average wagon load is about 1,200 1b. (Fig. 2). One shovelful of ore out of every ten is taken as a sample. Considerable ore is brought in from the outside mines, and this method of sampling is

Jan 1, 1916

By Arthur F. Taggart, A. W. Thomas, T.C. Fitt

It was noticed early by operators that high recoveries and flocculation of the sulphide minerals were closely correlated in agitation-froth flotation. Later, this readily visible flocculation was found almost invariably to be due to the binding together of the oiled sulphides by minute air bubbles, and is now known to be characteristic of pulps in which at least one of the mineral species is coated with an insoluble collecting oil. In 1930 it was reported1 that in differential flotation a correlation exists between Brownian movement of particles in the pulp and their nonfloatability, and that Brownian movement and dispersion are likewise correlated, whence it would appear to follow that dispersion of a mineral particle in a flotation pulp denotes a particle condition unfavorable to flotation. In 1934 it was postulated2 that Brownian movement, dispersion and nonfloatability all flow from the condition of the surface of the dispersed particles. It was also postulated at that time that the surfaces of dispersed particles are ionized, the ionized compound being a product of reaction between a component of the particle and a component of the pulp, of a mass solubility of the general order of a fraction of a milligram to I 5 to 20 mg. per liter. It was then further asserted, and has since been confirmed by Bankoff,3 that sulphides so conditioned with soluble collectors as to be floatable flocculate without the intervention of air bubbles as binding media. The present paper comprises an inquiry into the nature of the bound and counter ions in zinc sulphide dispersed by sodium arsenate. A part of its findings was mentioned in the 1934 paper above cited.= The tests show that: I. When powdered granular zinc sulphide is immersed in aqueous solutions of sodium arsenate, arsenate ion is abstracted from solution and anchored to the solid surface, while sulphate and lower sulphoxy ions are concurrently displaced therefrom in substantially stoichiometric quantities. 2. The ion counterbalancing the anchored arsenate ion is zinc. 3. Dispersion and Brownian movement of zinc sulphide are concurrently maxima at an arsenate-ion concentration lying between 0.01 and 0.001-molar sodium arsenate. 4. Any condition or reaction that tends. to remove the zinc arsenate coating from the zinc sulphide particles decreases dispersion and Brownian movement concurrently. Experimental Three samples of zinc sulphide were used. Lot I was C.P. zinc sulphide, washed well be~ond absence of chloride, as shown by test with silver ion. Lot 2 was prepared by precipitation from hydrochloric acid solution of arsenic-free zinc, and was washed as lot I. Lot 3 was prepared by heating a portion of lot 2 in absence of air at 1200° to r300°C. for one hour."

Jan 1, 1943

By Arthur F. Taggart, T. C. Fitt, A. W. Thomas

It was noticed early by operators that high recoveries and flocculation of the sulphide minerals were closely correlated in agitation-froth flotation. Later, this readily visible flocculation was found almost invariably to be due to the binding together of the oiled sulphides by minute air bubbles, and is now known to be characteristic of pulps in which at least one of the mineral species is coated with an insoluble collecting oil. In 1930 it was reported1 that in differential flotation a correlation exists between Brownian movement of particles in the pulp and their nonfloatability, and that Brownian movement and dispersion are likewise correlated, whence it would appear to follow that dispersion of a mineral particle in a flotation pulp denotes a particle condition unfavorable to flotation. In 1934 it was postulated2 that Brownian movement, dispersion and nonfloatability all flow from the condition of the surface of the dispersed particles. It was also postulated at that time that the surfaces of dispersed particles are ionized, the ionized compound being a product of reaction between a component of the particle and a component of the pulp, of a mass solubility of the general order of a fraction of a milligram to I 5 to 20 mg. per liter. It was then further asserted, and has since been confirmed by Bankoff,3 that sulphides so conditioned with soluble collectors as to be floatable flocculate without the intervention of air bubbles as binding media. The present paper comprises an inquiry into the nature of the bound and counter ions in zinc sulphide dispersed by sodium arsenate. A part of its findings was mentioned in the 1934 paper above cited.= The tests show that: I. When powdered granular zinc sulphide is immersed in aqueous solutions of sodium arsenate, arsenate ion is abstracted from solution and anchored to the solid surface, while sulphate and lower sulphoxy ions are concurrently displaced therefrom in substantially stoichiometric quantities. 2. The ion counterbalancing the anchored arsenate ion is zinc. 3. Dispersion and Brownian movement of zinc sulphide are concurrently maxima at an arsenate-ion concentration lying between 0.01 and 0.001-molar sodium arsenate. 4. Any condition or reaction that tends. to remove the zinc arsenate coating from the zinc sulphide particles decreases dispersion and Brownian movement concurrently. Experimental Three samples of zinc sulphide were used. Lot I was C.P. zinc sulphide, washed well be~ond absence of chloride, as shown by test with silver ion. Lot 2 was prepared by precipitation from hydrochloric acid solution of arsenic-free zinc, and was washed as lot I. Lot 3 was prepared by heating a portion of lot 2 in absence of air at 1200° to r300°C. for one hour."

Jan 1, 1943

By J. L. Bray, S. T. Ross

The paper provides electrometallurgical data on the problem of germanium removal from zinc sulphate solutions. Germanium traces have caused much concern to the zinc refiner. Confirmatory evidence of interaction between germanium and cadmium is presented. Statistical analysis of data expands its significance and enhances its value. Further research is outlined. THE literature contains many references to the effects of trace amounts of germanium in the production of electrolytic zinc. One of the authors had experience with this troublesome element as early as 1917 at Trail, B. C. In 1929, Tainton and Clayton' reported that concentrations of as little as one part per million of germanium were sufficient to cause serious losses in current efficiency. Liddell2 reported that trace amounts of germanium cause marked lowering of the hydrogen overvoltage of electrolytic zinc cells, so that commercial production was impaired. Bray3 recorded the history of germanium in relation to electrolytic zinc production, noting that concentrations below 10 ppm have been found to yield low current efficiencies and copious hydrogen evolution. Koehler' stated that germanium "when present to the extent of a small fraction of one part per million per liter, causes serious evolution of hydrogen with a corresponding reduction in current efficiency." Recently, however, S. W. Ross" reported, from Risdon, Tasmania, that "in the course of leaching . .. dissolved traces of germanium... if not removed almost completely ... increase the reversion of cadmium during the filtration of the copper-cadmium precipitate and reduce the current efficiency during subsequent analysis." The copper-cadmium precipitate referred to is the residue from the zinc-dusting purification of zinc sulphate leach solutions. In the face of such conflicting testimony and with the increasing industrial importance of pure germanium and zinc it was decided to investigate the relationship between cadmium and germanium. Furthermore, other work by the authors showed certain discrepancies to exist in the theories of Tainton, et al. In the laboratory, without marked efficiency decreases, the authors have deposited zinc successfully from solutions containing as high as 1 g per liter of germanium. This could be done only when there was no cadmium present. Preliminary investigations of the suspected rela- tionships were carried out by means of emission spectrographic analysis using a beryllium internal standard. Several solutions containing 100 g per liter of zinc, as zinc sulphate, and 1 g per liter of cadmium, as cadmium chloride, were prepared. These concentrations were on the order of those obtained during a commercial low-acid leaching process. Varying concentrations of germanium were added to these solutions so that the range of 0.0000 to 0.5000 g per liter of germanium was covered. A 250 ml sample of each solution was agitated with 2.5 g of zinc dust for 30 min, filtered, and the filtrates were examined spectroscopically. Qualitative evidences of cadmium traces were found in those filtrates which originally contained above 10 ppm of germanium. Reliability of the analytical method did not permit quantitative investigations since cad-Table I. Current Efficiencies Obtained at 0.0000 and 1.5000 G per Liter Cadmium Concentrations Ge Concentrastion,* Cd Concentration,* EtBclenoy, G per Liter G per Llter Pot 0.0000 0.0000 84.270 0.0010 0.0000 94.849 0.0050 0.0000 92.649 0.0075 0.0000 94.039 0.0100 0.0000 96.084 0.0000 1.5000 93.460 0.0010 1.5000 95.158 0.0050 1.5000 92.148 0.0075 1.5000 91.260 0.0100 1.5000 84.546 • Cd and Ge concentrations shown are those existing before zinc-dust purification. mium determination in the concentrations present in zinc-dusted solutions lacks sufficient sensitivity for reproducible results. As a consequence of the inability of the investigators to obtain acceptable results through direct quantitative analysis, an indirect approach was devised. This indirect method involved a study of the current efficiency, in a model zinc cell, as a function of the concentrations of cadmium and germanium. Variables such as cell temperature, voltage, current density, anode spacing, relative electrode area, degree of agitation, cathode preparation technique, time, acid concentration, and solution volume were held constant. Fig. 1 shows the cell used. The current was fur-

Jan 1, 1952

G. McMEANS*—This paper is a very good demonstration of the use of a new tool for the solution of industrial problems of a physical nature. To have solved this problem without the use of radioactive tracers would have required a far greater amount of investigation and work. The authors have described their work in such detail and in such a manner as to suggest the possibilities of the use of such tracer studies in the solution of many perplexing problems of industry. R. E. BREWER †—The authors are to be congratulated on this very excellent paper, which describes the results obtained by utilizing radioactive tracers in investigating the complicated reactions in the coking process. The paper has especial merit because the study was made under typical operating conditions in a commercial coke oven. Considering all the difficulties involved, the results obtained are excellent. My brief comments will relate primarily to the method used for determining the sulphur in the gas and to the value of the data obtained in stimulating further research. In discussing their results, the authors state (p. 17) that "Of the total sulphur charged to the oven in the coal 95 pct was accounted for in the coke and gas. Most of the sulphur unaccounted for is believed to have been lost in the gas, since the gas sampling system removed all the H2S but probably only part of the organic sulphur compounds present in the gas. Although sulphur in the acid-insoluble tar residue in the gas scrubbing bottles was determined and added to the total sulphur determination of each sample, it is doubtful whether an aliquot portion of tar for each sample was obtained." The reviewer believes that the authors might have obtained a better sulphur balance had they used an improved procedure for determining sulphur in the gas. The absorption train should have included a trap to remove the tar and am-moniacal liquor and a wash bottle containing 5 pct sulphuric acid to remove ammonia in the coke-oven gas before it entered the gas scrubbing bottles containing the ammoniacal cadmium chloride solution. Sulphur in the tar and

Jan 1, 1950

By T. D. Jones

MUCH the same story can be told for the lead industry for the year 1945 as for the three previous years. In response to inquiries as to new developments, invariably the answer has been, "No new developments-our men either too busy with the man-power problem or trying to get production out." Time and efforts of industry have been concentrated for the most part on war or readjustment problems. Now that V-E and V-1 day have passed, the lead industry can justly be proud of its record in World War II. As in previous wars, lead played an important role and one of its most spectacular uses was in the production of the atomic bomb. We read that the part lead played was rather obscure, but as a protective agent, lead played a most significant role. "Since the materials in the Pile Plant are intensely radioactive, all storage and handling must be done behind thick concrete walls or lead shields. The material is never seen and all operations are auto matically controlled by a foolproof remote control system especially designed for this purpose." (Chews. & Met., Sept. 1945.) When our armies invaded the European theater of war and made a landing on Normandy beach, gasoline and oil for the motive power were furnished through miles of armored lead pipe. This amaz-

Jan 1, 1946