Search Documents

Jan 1, 1910

THE bellows are important and necessary agents in most melting processes. In addition to seeing that these have sufficient soft cloth, extend far and wide, and are of good design, including good valves and good long tubes, and that they cannot break and lose the air received, it is very important to give attention to their installation so that they may easily effect their purpose. Therefore I now wish to proceed by noting some common devices for moving them, both with water and with man power, so that you may make use of them as the need arises.

Jan 1, 1942

By R. A. Matuszak

Abstract-Throughout the history of power excavating machines, engineers have continuously tried to shape the main drive speed-torque characteristics to provide an optimum performance from each main motion. Selection of prime mover for the various motions has been the subject of many engineering studies and most forms of energy conversion have been tried. A new form of electrical power conversion looms on the horizon as the most optimum yet. Controlled frequency operation of a squirrel cage induction motor increases the reliability of the most reliable form of energy conversion (electrical) found thus far, and improves the performance characteristics.

Jan 2, 1978

By G. F. Huff, G. R. Bailey, J. H. Richards

An improved bomb-sampling technique for obtaining samples for oxygen analysis from liquid steel is described. Analyses of samples taken from open-hearth furnaces by the improved method show sufficient agreement with laboratory data to indicate the accuracy of the method is better than that of other existing sampling methods. THE bomb-sampling method of determining the oxygen content of a liquid-steel bath was studied by obtaining and analyzing more than 200 samples from normal open-hearth heats. Of these samples, about 60 were obtained with a bomb of conventional design;' the remainder were taken with a somewhat modified bomb designed to give greater protection against slag contamination. In the new device, the contacting faces of the cast-iron mold halves are machined so that they fit closely; the opening at the top of the bomb is covered with a thin steel cap; and the top of the bomb is further covered with a wood block held in place by heavy steel wire. After the bomb has passed through the slag layer and has entered the steel bath, the wire melts and the wood block floats to the surface. Thereafter, the steel melts through the thin cap and flows into the bomb cavity where it is deoxidized with aluminum wire. An assembled bomb, ready for sampling, is shown in Fig. 1. To standardize sampling procedure, the samples were usually taken through the center door and at the bottom of the furnace; that is, the bomb was on the bottom when the metal cap melted. After each addition to the furnace, at least 20 min elapsed before a sample was taken. The oxygen contents of all the samples were determined by using the vacuum-fusion method, two or more specimens from each sample being analyzed. The specimens were cubes of metal cut from a region in the interior of the bomb sample, as shown in Fig. 2. Drillings for carbon analysis were obtained immediately above the oxygen-analysis region. Reproducibility of Results In determining the reproducibility of the results obtained with the modified bomb, the following four factors were studied: 1—variation in the oxygen concentration of duplicate specimens taken from a single sample; 2—variation in the oxygen concentration of duplicate samples taken in quick succession: 3—effect of the amount of aluminum wire

Jan 1, 1953

By Paul M. Tyler

THE farmer pays the phosphate miner! Phosphorus is used in fireworks; goes to battle in military smoke screens, incendiary shells, and tracer bullets; and, in vermin destroying pastes, does its part in the war against insects. A lemon phosphate can be had for a nickel at most soda fountains, and tens of thousands of tons of phosphate rock are mined annually for use in the food industries, chiefly for making monocaleium phosphate baking powder. Sodium phosphate cleaning, washing, and scouring compounds consume substantial quantities: the iron and steel industries buy a few thousand tons yearly to make ferrophosphorus and to balance foundry-iron furnace charges; and even nonferrous metallurgists use a little for phosphor bronze and other alloys. Phosphoric acid, its salts, and diverse other derivatives of this versatile element have countless applications, and industrial outlets are increasing rapidly, especially in the United States. Nevertheless, in this country nearly 90 per cent and in the whole world fully 95 per cent of the phosphate rock consumed is absorbed ultimately in agriculture.

Jan 1, 1938

By J. T. Norton, J. G. McMullin

The ternary system of gold-silver-copper is characterized by a solid solubility gap and a two phase region in which copper-poor and silver-poor phases coexist. At about 30 pct gold, the two phases become mutually soluble at temperatures below the melting temperature. As the gold content is increased, the solubility temperature of the alloys decreases until at about 80 pct gold, the two phases are soluble down to the lowest temperature at which the alloys will recrystallize. Although the general form of the two phase region is known, its boundaries do not seem to have been investigated extensively. In an X ray diffraction study, Masing and Kloiberl have outlined the boundaries of this two phase field at 400 and 750°C. Using only microscopic techniques, Pickus and Pickus2 determined a vertical section of the ternary diagram showing the 14 kt alloys (58.3 pct gold). These two reports are riot in complete agreement. It has been shown3 that some of the ternary alloys are susceptible to age hardening and that the hardening is caused by the separation of a homogeneous alloy into two phases at the aging temperature. While the gold-copper binary system is an outstanding example of super lattice formation, Hultgren4 has shown that a few per cent of silver added to gold-copper destroys the tendency for ordering. Because of the age hardening possibilities of these alloys, it seemed advisable to investigate the boundaries of the two phase field more in detail using an X ray diffraction method, so as to permit a better understanding of the aging phenomena and enable predictions as to the behavior of other alloys to be made. This is especially true for the 18 kt alloys (75.0 pct Au) at the lower temperatures since they are known to exhibit age hardening. Twelve ternary alloys were prepared having the compositions shown in Table 1 and graphically in Fig 1. The gold used was fine gold bars supplied by Handy and Harmon. The silver was a bar of high purity silver from the U. S. Bureau of Standards. The copper was a bar of vacuum-treated, high conductivity copper from the National Research Corporation. The pure metals in the form of powder were weighed out in proper proportions and melted in graphite in a high frequency induction vacuum furnace. They were heated to 1100°C and slowly cooled. The ingots were then removed from the crucible, inverted, returned to the crucible and remelted. This remelting procedure was intended to reduce segregation in the ingots. After remelting, the ingots were checked for weight loss. The weight loss in each ten gram ingot was held to less than 25 mg. The remelted ingots were cold rolled and then given a homogenizing heat treatment of 16 hr at 760°C to remove any remaining segregation. Powder specimens were prepared by cutting the ingots with a fine file, one half the required amount of powder being taken from each end of the ingots. When the X ray diffraction pattern showed any difference in lattice constant between the ends of the ingot, the ingot was remelted and given an additional homogenization treatment. All powder samples were sealed in evacuated pyrex tubes for heat treatment. Ordinary pyrex proved satisfactory for temperatures up to 650°C but above that temperature it was necessary to use a special high temperature pyrex glass. Annealing at temperatures below 500°C was done in a salt bath whereas for temperatures of 500°C and above an electric muffle furnace was used. In both furnaces the temperature control was ± 5°C. In all annealing treatments samples of cold worked powder were placed in a furnace which was already at temperature. In this manner the specimens recrystallized directly to the equilibrium structure for that temperature. Time at temperature was selected so as to allow complete recrystallization, but very little grain growth. Specimens were quenched from the annealing temperatures by breaking the pyrex tubes in cold water. X ray diffraction photograms were made of all the heat treated powders using copper radiation and a Phragmen

Jan 1, 1950

By C. S. Allen

WITH increased coal production and mechanization of coal mines many transportation problems arise. The main objective is to bring the coal to the tipple or dump it as quickly as possible. Larger and faster haulage locomotives or two locomotives connected in tandem have been adopted to solve the problem. Motor equipment, gears and control systems of locomotives to be placed on these hauls are carefully studied to meet these requirements, by an analysis of motor characteristic curves with the corresponding tractive effort curves, in order to determine the correct load for maximum efficiency and to determine the approximate schedule. Control equipment is usually considered to be the controller and resistance. Sometimes accelerating curves are calculated in order to obtain smooth starting in the least possible time without slipping the wheels. Train control is very important, but why limit this to acceleration? Deceleration or retardation of the locomotive is a part of the train control and should be given as much consideration as the control for acceleration. TYPES OF BRAKING Common braking systems for mine locomotives utilize screw-type mechanical brakes, dynamic braking and the air brake. For gathering and haulage locomotives, the screw-type mechanical brake is regarded as standard. A brake of this kind cannot be applied without much effort and lapse of time. Motormen, like other people, follow the path of least resistance, and therefore have their brakes ready for instant application-which means that the shoes are virtually dragging. Even then, a motorman bucks and plugs the motors to gain time and avoid as much physical effort as possible. "Bucking of motors" consists in turning the reverse cylinder of the controller to parallel position corresponding to the opposite direction of travel while the locomotive is in motion, without applying power from an external source. When this occurs, both motors tend to act as series generators, because the armatures are revolving and there is residual magnetism in the field circuit. Owing to slight differences in motor manufacture, one of these will generate a slightly higher potential and will overcome the generated voltage of the second and tend to drive it as a motor in the reverse direction. This action retards the locomotive but is very severe on the segments of the reverse cylinder and on the motor commutators. "Plugging motors" is the application of power to the motors corresponding to the opposite direction of travel. In order to "plug" the motors it is necessary first to "buck" them (which reverses the connections to the motors) and then to apply

Jan 1, 1941

By Albert Sauveur

The instrument about to be described meets so perfectly the special needs of the metal microscopist that there eeeme to be little doubt but its merits must be readily appreciated by those who have had any experience in the microscopical examination of metals. The Microscope-Stand.—The microscope-stand proper, Fig. 1, consists of a microscope-tube, provided with both coarse and fine adjustments of the best construction, and with a draw-tube, rigidly mounted on a bar supported at both ends on substantial and firm cast-iron legs. The height between the table and the under side of the supporting bar is 5 in. and the distance between the supporting legs 12 inches. This arrangement affords free space below the objective for the examination of large epecimens of metals, such as full rail-sections, without detracting in the least from the value of the

Jan 1, 1912

By C. F. Cigliana

TO accommodate a large tonnage at high speed from a single level at San Manuel, a very flexible haulage system was designed to give maximum access to stoping areas, minimize delays, and pro- vide for safety. With these requirements as a guide, the haulage was laid out as a simple double loop with one-way traffic of continuous pull. These loops consist of two parallel drifts 100 ft apart, center to center. Haulage drifts are numbered from north to south, the northernmost being the No. 1 drift. This holds true on both the North and South haulage loops. Haulage drifts are connected at 1000-ft intervals with crossovers so that it is possible to bypass any given section that may be inaccessible. Two of these turnouts are double diamonds, one located on the approach to the rotary dumps at the hoisting shafts and the other on the departure from the dumps. The turnout on the approach or North haulage is 835 ft in front of the rotary dump, and the one on the departure, or South haulage, is 1058 ft from the dump. This type of turnout allows trains coming down either haulage drift No. 1 or No. 2 to be routed into either shaft and expedites movement by avoiding delays due to congestion in the dumping area. The double diamond on the return haulage loop facilitates returning empty ore trains to the panels.

Jan 5, 1958

By Oliver Bowles

THE most important non-metallic mineral industries from a tonnage standpoint are those that are allied with the construction industries and are engaged in handling sand and gravel, crushed stone, building stone, cement, lime and gypsum. The greatest problem facing a number of these industries at this time is over-production. They have experienced un- usual, and in some instances phenomenal, growth during recent years, stinlulated by extensive highway and building construction, but in some localities expansion of producing plants has far outstripped industrial needs. The cement industry is operating at about two- thirds capacity. Over-production tends toward price- cutting and unprofitable and interrupted operation, involving maintenance expenses for idle plants and disorganization of working forces. This condition has encouraged active efforts toward reducing production costs by the introduction of labor-saving equipment. Also, there is a tendency toward the location of manufacturing plants, wherever possible, near the centers of consumption rather than at points of production of raw materials. In order to reduce overhead expense, or for other reasons, many consolidations of companies into larger units have taken place. An economic study of conditions in these industries is highly desirable. The U. S. Bureau of Mines has taken one step forward in this direction in the issuance of Economic Paper 7, entitled "Economics of New Sand and Gravel Developments." Briefly, this report emphasizes the importance of making a thorough study of all the economic factors involved before undertaking new .enterprises.

Jan 1, 1930

By S. T. Wlodek

The scale md subscale reaction products were identified and their rates of formation were studied in air over the range 1600" to 2000°F (871 " to 1149°C) for periods of up to 400 hr and for hoth the solution-annealed and aged conditions. The effect of prior sltrface preparation on suhscale oxidation was also studied The general oxidation behavior of both Ni-Cr-Mo-Al-Ti type alloys was similar. A surface film of a, Al2O3, forms immediately on exposure Subsequent oxidation continued at a linear rate (QL = 55 * 5 kcal per mole) as colonies of Cr2O3 nucleated at the A12O3/gas interface Further oxidation proceeded at a paraholic rate zvhiclz could he fitted to two successive rate constants. During paraholic oxidation, and depending on temperature, the scale consisted of Cr2O3, NiCr2O4 , and TiO2 with traces of NiO. In the case of Rene 41, the activation energy of both paraholic processes was 66 * 3 kcal per mole suggesting that diffusion of cations tlzrozrgh Cr2O3 was the rate -determining process. An unusual decrease in the oxidation of Udimet 700 at 1900°F where a spinel of Ni(A1,Crh0, zuas the predominant reaction product prevented the accurate assignment of activation energies for this composition. In both alloys internal oxidation of Al2O3 commenced shortly after parabolic scaling was observed. Prolonged exposure prod7tced intemal oxidation of TiN, and in Udimet 700 a complex Mo-Ni nitride was also found. At 1900oF, the subscale reactions in Udimet 700 undergo an inversion which parallels the decrease in surface oxidation; internal oxidation ceases hut is replaced by the formation of "spherodized" 3.' colonies. Surface-preparation techniqtles which introduce appreciable working, such as coarse surface grinding or grit blasting. increase the amount of alloy depletion and internal oxidation in Reni 41. The reverse is true of Udimet 700 for which electropolished or mechanically polished specimens show much more subscale oxidation than strongly worked stirfaces. The strongest commercial nickel-base alloys presently available are generic to the Ni-Cr-Mo-A1-Ti base which exploits the precipitation of Ni3(A1,Ti) as the main strengthening mechanism, while relying on solid-solution strengthening by molybdenum and chromium reinforced by the pre- cipitation of carbides to attain maximum properties. This study characterizes the oxidation behavior of Rene 41, the strongest alloy of the Ni-Cr-A1-Ti type commercially available in sheet form, and Udimet 700, whose higher aluminum and titanium content allows it to exhibit one of the more attractive combinations of high-temperature properties available in a wrought product. The scaling processes of complex, type nickel-base alloys have received relatively little attention. Malamand and vidal as well as Poulignier et al.2'3 have determined the composition gradients across the metal/oxide interface produced by high-temperature oxidation and considered the effect of surface perature, Limited weight-gain data has also been published by Fere 5 for alloys of this type and Radavich6 has identified the reaction products on Udimet 500 and Inco 702 after oxidation at 1832°F. Reference can, of course, be made to the excellent reviews of Kubaschewski and Hopkins7 or Ignatov and Shamgunova8 for a summary of the data available on the oxidation of binary and ternary alloy systems which are related to the more complex alloys considered here. EXPERIMENTAL The analyses of the different commercial heats studied are given in Table I. Using the experimental procedures previously established,9 continuous weight-gain data were obtained on both heats of Rene 41 sheet (A and B) and 150-mil-thick slices of cast Udimet 700. Subscale oxidation reactions were followed by static exposure of cylindrical specimens obtained from swaged Rene 41 (Heat C) and Udimet 700 (Heats E and F). In brief, continuous weight-gain tests were performed on specimens with a surface area of 10 to 12 sq cm. These were abraded through 600 grit Sic paper, electropolished to 2p rms in an electrolyte of 10 pct H2So4 in ethanol, and lightly etched in 10 pct HCl in ethanol before final washing and rinsing in ethanol. All continuous weight-gain data were obtained in dried (-70°F dew point) flowing (1 liter per min) air to an accuracy of +0.1 mg. Subscale oxidation processes were followed by the metallographic examination of 0.5-in-diam by 1.0-in.-long specimens. After an initial center-less grinding, various additional surface treatments were employed to determine the effect of surface preparation on subscale oxidation processes. Before exposure in zirconia crucibles, all samples were lightly etched in 10 pct HCl-ethanol, washed in ethanol, and dried. The depth of internal oxidation was measured to ±0.00025 in. on unetched specimens mounted so as to provide a taper mag-

Jan 1, 1964

By AIME AIME

ORGANIZATION of The Federated American Engineering Societies was effected at the organizing conference of national, local, state and regional engineering and allied technical organizations at the Cosmos Club, Washington, D. C., June 3 and 4. Thus is brought into being the greatest national engineering society in the world. The object of the organization is to further the interests of the public through the use of technical knowledge and engineering experience, and to consider and act upon matters common to engineering and allied technical professions. Prominent engineers from all parts of the country, representing more than 75 engineering societies, with an aggregate membership of more than 125,000, participated in the organization. The constitution as adopted by the conference, calls for the creation of s managing body to be known as the American Engineering Council, and its executive board. The belief was expressed that the entire organization would come to be spoken of as the American Engineering Council. The council is to coordinate the activities of state councils and of local affiliations whenever these activities are of national or general importance or may affect the general interests of engineers. Representation in the council is to be according to membership of the component societies.

Jan 1, 1920

By A. L. Marshall, F. J Norton

The object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate, of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C. in a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. Apparatus and Technique The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system , will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 1800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by unscrewing the lower nut, and the new

Jan 1, 1944

By A. L. Marshall, F. J. Norton

The object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate, of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C. in a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. Apparatus and Technique The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system , will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 1800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by unscrewing the lower nut, and the new

Jan 1, 1944

By S. F. Shaw

The Sierra Mojada mining district is situated in western Coahuila, about 8 km. east of the Chihuahua state line, and about one-half way from the northern to the southern extremity of the state. It is at the terminus of the Mexican Northern R. R., 125 km. northeast of Escal6n, Chihuahua; also about, 240 km. due west of Monclova, Coahuila. The altitude is approximately 1500 m. above sea level. The Sierra Mojada valley is about 10 km. long, from east to west, with a width of 1 to 2 km. It is approached from the east through the Puerto del Oro, where the Mexican Northern R. R. enters the valley; the slope from west to east is gentle. The Sierra Mojada, of which about 300 m. is an almost vertical wall, bounds the valley on the south side; on the north side, the slope to the crest of Sierra Planchada is more gradual, rising only 200 or 300 m. above the valley. Water is relatively scarce in the district, and there are no running streams. The rainy season, usually beginning at the middle of June, lasts through July, and occasionally into August or September. In some years the rains fail entirely. The slope of the ground is such that nearly all the water immediately runs off. The arroyos along the flanks of the mountains are not very deep, but in heavy rains, sometimes approaching cloudbursts, a tremendous volume of water rushes down them, carrying large boulders. A certain amount of seepage collects in the agglomerate, lying below the conglomerate, and is retained in the local fractures. Some shallow wells have been sunk in this agglomerate, and one well over 150 m. deep was sunk on the Volcan ranch, supplying about 76 1. (20 gal.) per min. A considerable supply of water is collected in large earth reservoirs in and below the town of Esmeralda. In ordinary years this supply will last until January or February, after which the Volcan well has to be depended on until the next rainy season. Vegetation is scarce, aside from scanty scrub oak and other brush in the mountains, and a few mezquite, locust, pepper, and cottonwood trees

Jan 1, 1923

By S. F. Shaw

The Sierra Mojada mining district is situated in western Coahuila, about 8 km. east of the Chihuahua state line, and about one-half way from the northern to the southern extremity of the state. It is at the terminus of the Mexican Northern R. R., 125 km. northeast of Escal6n, Chihuahua; also about, 240 km. due west of Monclova, Coahuila. The altitude is approximately 1500 m. above sea level. The Sierra Mojada valley is about 10 km. long, from east to west, with a width of 1 to 2 km. It is approached from the east through the Puerto del Oro, where the Mexican Northern R. R. enters the valley; the slope from west to east is gentle. The Sierra Mojada, of which about 300 m. is an almost vertical wall, bounds the valley on the south side; on the north side, the slope to the crest of Sierra Planchada is more gradual, rising only 200 or 300 m. above the valley. Water is relatively scarce in the district, and there are no running streams. The rainy season, usually beginning at the middle of June, lasts through July, and occasionally into August or September. In some years the rains fail entirely. The slope of the ground is such that nearly all the water immediately runs off. The arroyos along the flanks of the mountains are not very deep, but in heavy rains, sometimes approaching cloudbursts, a tremendous volume of water rushes down them, carrying large boulders. A certain amount of seepage collects in the agglomerate, lying below the conglomerate, and is retained in the local fractures. Some shallow wells have been sunk in this agglomerate, and one well over 150 m. deep was sunk on the Volcan ranch, supplying about 76 1. (20 gal.) per min. A considerable supply of water is collected in large earth reservoirs in and below the town of Esmeralda. In ordinary years this supply will last until January or February, after which the Volcan well has to be depended on until the next rainy season. Vegetation is scarce, aside from scanty scrub oak and other brush in the mountains, and a few mezquite, locust, pepper, and cottonwood trees

Jan 1, 1923

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

ONE of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing of the A.S.T.M., 1938. The work of Mann,1 Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserve especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by [P OL, plotting So = Ao as a function of eo = Lo] where A o and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors' It was shown that the true physical behavior of the material in the tension test could best be represented [by plotting the average true stress, S = P as a function of e = q' = log o = log Log] where P, A, L, S, e, and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximum load point to fracture. The construction of such- curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain difficulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece

Jan 1, 1941

By Morris J. Elsing

FOR MANY YEARS lead and zinc have had the so-called protection of a tariff and it is the purpose of the following brief discussion to show what' such protection actually accomplishes with a view to forecasting the possible results of the present copper tariff. In analyzing the subject, tabulations of the United States production, consumption, imports and exports, including ore and concentrates and all of the metallic products, of both lead and zinc have been made for each year since 1900. Of these data, the relationship of the imports and exports and the relative foreign and domestic prices are shown in Table 1. The conclusions drawn from these figures are listed below. 1. The United States is an exporter of zinc. 2. The United States is an importer of lead. 3. The average price of zinc at St. Louis for the last 32 years has been no higher than on the London market even though zinc and zinc ore have "enjoyed" a protective (?) tariff of varying amounts per pound for 22 years of this period. 4. The average price of lead on the New York market for 32 years has been 1.2c. per pound higher than on the London market, the tariff varying from 0.75 to 1.5c. per pound of lead in ore, and 1 to 2c. or more on manufactured lead.

Jan 1, 1932

By C. W. Stratford

[During the last few years, the necessity for development work has been generally recognized by executives throughout the oil industry, resulting in greatly accelerated progress and the adoption of many noteworthy improvements in refining methods and equipment. Several years ago, the Associated Oil Co. decided to improve distillation methods with the object of reducing refining costs. This extremely interesting work was entrusted to the writer, and W. S. James, now Chief of Research for Studebaker Corpn. of America, was selected as the principal collaborator. The latter contributed much during his two years with the Associated Oil Co., to the development work that has followed. The writer extends to the Associated Oil Co. his appreciation for permission to disclose the details of distilling equipment. In petroleum refining the principal requisites of good economics are the separation of high-priced distillates from those of lower price; maxi-mum yield of any desired distillate; lowest capital investment in refining equipment; lowest cost of operation and maintenance, and the best adaptability and flexibility of the same refinery equipment for handling crudes of widely varying characteristics. The first two items mentioned, separation and yields of distillates are determined by efficiency of fractionating equipment,. Discussion in this paper is chiefly concerned with oil-heating equipment, combustion and furl economy. It has long been well known that velocity plays a very important part in all heat transfer systems. Any betterment in specific transfer. rates in such systems must. always involve velocity. Realizing this fact, IV decided to adopt as a basic principle, the employment of energy to impart velocity required for high transfer rates through a heating diaphragm, and our method of modernizing obsolete shell stills is founded on this principle. Mechanical energy is usually cheap and its rational rspcntliture is returned in the form of greatly increased heat transfer rates, on both oil and gas sides of the sheet. Certainly there is nothing new in this principle, the only novelty being that of our peculiar method of application On the oil side (Fig. I) use is made of a centrifugal pump to jet the oil against the heated sheet thereby creating a high velocity sheet flow over the entire fired area. Such a pump is one of the most efficient machines, so far developed, for moving fluids. 'I'he oil, under pressure impinging

Jan 1, 1928

By C. R. Hayward, H. O. Hofman

The aim of instruction in a metallurgical laboratory is to make real the principles on which metallurgical processes and operations are based, and to foster the spirit of investigation. The materials with which experiments are carried out are ores, metals, and metallic compounds. The method varies with the end sought. A class may work as a whole, each member contributing his share to the solution of a problem, or the students may carry on investigations independently; the former exemplifies class-research; the latter, individual research. It is with a branch of the former, with special reference to ore-treatment, that the present paper deals. In smelting an ore by a well-established process, the result is shown by analyzing the products to see whether their compositions correspond to those calculated in making up the charge; by taking account of stock to show the distribution of metal in the different products made and the losses from dust and volatilization; by casting a thermal balance to find the distribution and losses of heat; and by making a cost-sheet to ascertain, as far as possible, the necessary outlay of money. In lixiviation and amalgamation, the mode of operating has to be varied to adapt a process to the individual ore. Here a number of tests become necessary. Each will consist of a series of experiments with one variable, in order to find the conditions under which the variable gives the best result; a summary of several tests will give the best method of operating. Working a number of charges with the best method will furnish the data desired for ascertaining the recovery of metal,

Jan 1, 1910