Search Documents

By A. J. Teplitz, R. J. Goodwin

A new type water shut-off for use in air drilling has been developed. The method has been 99 to 100 per rent effective in several different formations of inter-ranular-type porosity. Since costs for materials, time and equipment used are relatively small, the process should extend economies of air drilling to many new areas. The treatment involves a new technique for forming a water-inroluble precipitate within the pores of a rock. Advantage it taken of the difference in mobility of a liquid and a gas in porous media to achieve the greatest volume of precipitate in a given pore. Reactants selected for the laboratory (2nd field tests were aluminum sulfate solution and gaseous ammonia. This process has been tested in both intergranular and fractured-type porosities. It has consistently shut-of between 99 and 100 per cent of the water flowing from formations having intergranular-type porosity and perrlreuhilities ranging from a few millidarcise to over a darcy The treatment is not particularly suitable for shutting-off water from fractured formations although plugging of the order of 50 per cent or greater has been achieved in all such applications. Among advantages of the treatment are: (I) no reaction waiting rime after a relatively short placement time, (2) a low mate-rials cost of about $3/f1 of hole treated, (3) use of common service-type equipment for treatment, and (4) no unusual requirements for mixing and placement. INTRODUCTION In rotary drilling with air or gas it has been possible to increase bit life by tenfold and more than double rate of penetration over corresponding performance when drilling with mud. These factors have amounted to as much as 22 per cent savings on total cost of drilling a well. However, these advantages are rapidly lost when water is encountered in an air- or gas-drilled well because water interferes with the removal of cuttings from the hole and also gives rise to other difficulties. In attempting to combat water troubles, operators have commonly resorted to such measures as mist drilling, treatment with cement or chemicals, converting to conventional mud drilling, or setting casing. In many cases these measures have either been costly or ineffective. In an effort to overcome this problem, studies were undertaken to develop an effective and economical water shut-off technique for use in formations possessing inter-granular-type porosity. Extensive laboratory experimentation finally led to a unique method for producing a water-insoluble precipitate within the pores of a sandstone. The unique part of the treatment is use of a liquid and a gas to form the precipitate, and in this case the reactants used were aluminum sulfate solution and gaseous ammonia. The reaction between these two materials is shown in the following equation. Al2 (SO1)3 - 18 H20 6NH2? saturated Water- Solution Cat 2A1(OH)3 . n H20 3(NH4)2SO • n H20 Solid Solid That is, a solid precipitate consisting of aluminum hydroxide and ammonium sulfate is formed when ammonia reacts with aqueous aluminum sulfate. The aluminum hydroxide is insoluble in water and the ammonium sulfate, though soluble, can only be removed from the formation pores by diffusion—an extremely slow process. Although the precipitate formed by the reaction is not particularly firm, great strength is not needed for a precipitate to bridge and plug intergran-ular-type porosity. A flow path in such a system is extremely tortuous and involves a great variety of pore

By Hal T. Morris

The main Tintic mining district in central Utah has produced approximately 13,500,000 tons of ore, containing silver, lead, gold, copper, zinc, and other metals, valued at more than $315,000,000. More than 90 per cent of this ore has come from large, irregular ore bodies that have replaced folded and faulted limestone and dolomite strata. Of lesser importance are replacement veins that chiefly cut contact-pyrometasomatized carbonate rocks and fissure veins that cut altered intrμsive bodies and volcanic rocks. The district is in the west-central part of the East Tintic Mountains, a north-trending fault-block range near the eastern margin of the Great Basin. The consolidated sedimentary rocks exposed at the surface and in mine workings are miogeosynclinal deposits more than 10,000 feet thick that range in age from late Precambrian to Late Mississippian. They are folded and strongly faulted and are partly overlain by volcanic tuffs and agglomerates and by extensive flows of porphyritic and vitrophyric quartz latite, latite, and trachyandesite of Eocene age. All of these rocks are locally concealed beneath thick alluvial deposits of Pliocene and Quaternary age. The Eocene and older rocks are cut by dikes, sills, and small stocks of porphyritic quartz monzonite, monzonite, and latite, which are genetically related to the ore deposits. The district is inactive except for the production of halloysite clay and for minor leasing activity and exploration ventures. Several exploration targets remain untested.

Jan 1, 1968

By Fred Bond

THERE is acute need for a method that will measure the size distribution of finely di-vided materials, particularly when the par-ticle sizes are smaller than the openings of the finest screen cloth regularly available for testing. Several methods and types of apparatus are in common use, but none are entirely satisfactory for all purposes. The commonest methods are microscopic grain counts, elutriation by liquids or air, and sedimentation. Valuable results have been secured by air elutriating devices, typified by the Haultain Infra-Sizer and the Pearson Air Analyzer. These are especially useful in obtaining sized fractions that can be examined and analyzed separately. They are particularly advantageous because the sizes of the sam-ples produced are adequate for a consider-able amount of subsequent manipulation and testing. The sedimentation methods, such as the Wagner and Klein turbidimeters, and the sedimentation balance, do not deliver sized fractions, but they do provide a means for reasonably rapid comparative determina-tions of fineness and surface area, which are important in many industries. The sedimentation balance consists essen-tially of a balance pan suspended in a liquid that contains falling particles. These are weighed as they settle onto the pan, and the time rate of settling is determined. The size distribution is computed from the set-tling rate. The balance appears to be in-herently more accurate than any of the other methods, and it has served a useful purpose in the study of numerous problems, but there have been limitations which have re-stricted its scope of application. Because of the essential simplicity of the method, it was felt that intensive investiga-tion might lead to modifications that would make it a valuable tool for the operators in industries that require precise information regarding the results secured from grinding equipment. A large number of size-distribu-tion determinations below 200 mesh were required in connection with a particular research problem in fine grinding. The sedimentation balance was used, in this investigation, and a technique was gradually developed that ultimately gave good results. A serious difficulty appeared, early in the work. It was discovered that less material always settled on the sedimentation pan and more on the bottom of the containing jar than could he accounted for by calculation, and also that the material that settled to the bottom of the jar outside the edges of the pan was considerably finer than that on the pan. This segregation was so great that the dis-tribution obtained for the finer sizes was obviously very much in error; material ground to about the degree of comminution of cement might have only 60 per cent of the calculated weight actually settling on the pan, and the error increased with the fine-

Jan 1, 1939

By J. Ruzicka

IN creep testing, material is subjected to a constant load, preferably at a constant temperature, and its rate of deformation is measured. The method of loading can be of various types but in this paper only creep testing under tensile load will be considered. The ordinary tensile test is essentially a comparison test in conditions that frequently bear little or no relation to those under which the test material is to be used in service. The purpose of creep tests is to measure the strength of the test material at slow rates of deformation that more nearly approach the rates realized in service. One purpose of this paper is to illustrate that the creep test, in addi-tion to its value as a service test, is superior to the ordinary tensile test as a sensitive tool for the comparison of certain metals in investigative testing. The other purpose is to describe equipment having distinctive features of design that make it especially suitable for such tests. Representative data obtained with this equipment on a group of rolled zinc-base materials are given. These data are compared with those from practical comparison tests of the creep type on weatherstrip fabri-cated from the same group of materials. The comparison illustrates the value of the fast creep test and of the equipment.

Jan 1, 1937

By Malcolm F. Hawkes

AUSTENITE grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, machinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to provide knowledge of the grain-size -characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstructures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The problem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will be considered first. More than So commercially produced cast steels representing a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules; namely, one hour at 1550°F, one hour at 1700°F, and six hours at 1700°F. The list of steels and results obtained on them will be found in the appendix. (See page 21.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT METHODS SUITABLE FOR DETERMINING AUSTENITE GRAIN SIZE AFTER HEAT- TREATMENT AT ORDINARY TEMPERATURES AND TIMES It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1947

By C. A. WARNER

AN OIL and gas mining lease contract, as entered A into by and between 'the lessor and the lessee, contains certain express covenants stipulating, in part at least, the exact performance thereof; it also contains certain implied covenants, among which may be included that of protection of the leased premises against drainage by the drilling of necessary offset wells. In the drilling for, and production of, oil and gas, however, it not infrequently happens that the lessee, acting in good faith, does not deem it prudent to, drill a test thereon even though the location for such test is offset by a producing well on an adjoining lease. Such conclusion, on the part of the lessee, is generally construed by the lessor as constituting a breach of the implied covenant mentioned above, and he may take proper action to secure satisfaction therefor. The action against the lessee is generally for cancellation or relinquishment of the lease, together with, or apart from, claims for damages allegedly sustained through failure to properly protect against drainage of the leased premises.

Jan 1, 1931

By R. W. Gurry

IN the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and 1110°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon content of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched. The mean result of concordant measurements is that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C. (1755°F.) and 1.89 per cent at 1110°C. (2030°°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutectoid temperature (738°C. or 1360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature1135°C. (2095°F.) instead of the commonly accepted value of about 1.7 per cent. EXPERIMENTAL PROCEDURE The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.1 In the empty furnace the range of temperature over a distance of 4 cm, at the heat center was 9°C. (16°F.) but at a given location the temperature remained within ±0.5°C. (0.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (1760°F.) and 1110°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with

Jan 1, 1942

By K. M. Myles

The vapor pressure of palladium over a series of Rlz-Pd alloys has been measured by the torsion-effusion method. The thermodynamic properties of the alloy system at 1575=K have been calculated from the vapor pressure data. The activities and the free energies of formation exhibit large positive deviations from ideal behavior. The enthalpies of formation are endother-mic. The entropies of formation are positive and larger than the ideal entropy of mixing. All of the thermodynamic properties suggest that a strong tendency toward phase separation exists in the solid solutions. The possible origin of the phase instability and the various factors that influence the thermodynamic properties are discussed. RECENT studies of the thermodynamic properties of alloys of palladium with nontransition elements have indicated that a significant contribution to the enthalpy of formation is related to the redistribution of the conduction electrons upon alloy formation.'-' The present work was undertaken to ascertain the importance of this contribution in Pd/transition-metal alloys. The Rh-Pd system was chosen for this investigation for several reasons: 1) The thermodynamics of the system were unknown. 2) Rhodium and palladium are completely soluble at high temperatures; below 1118OK the solid solution becomes immiscible.', 3) The difference in magnitude between the vapor pressures of rhodium and palladium permitted the use of an existing effusion apparatus. 4) Additional information was known about the alloy system that would facilitate the interpretation of the thermodynamic results. EXPERIMENTAL PROCEDURE The thermodynamic properties of the Rh-Pd alloy system were calculated from the vapor pressure of palladium over solid palladium and over several solid Rh-Pd alloys. The vapor pressure was measured by means of the torsion-effusion apparatus that has been described previously. In this method, an effusion cell is suspended from a tungsten filament inside a high-temperature furnace. Two orifices are located eccentrically such that the effusion of the vapor creates a rotational torque in the filament. The angle of rotation is directly related to the total vapor pressure within the cell. As the vapor pressures of rhodium and palladium are approximately five orders of magnitude apart," the total vapor pressure was considered to be effectively equal to the equilibrium vapor pressure of palladium. The effusion cells were made from high-purity alumina since auxiliary experiments indicated that essentially no reaction occurs between alumina and solid Rh-Pd alloys. Unfortunately, because the orifices were irregular, an accurate calculation of the Free- man-Searcy correction factors" could not be made. The constants were determined in an independent experiment where the vapor pressure of copper, as measured in the alumina cell, was compared with an accurate value of the vapor pressure, which had been determined previously.4 Depletion of palladium from the surfaces of the specimens was minimal as the deflection of the cell remained constant, for at least 15 minutes, at each of the experimental temperatures. Lattice parameter measurements of the postrun alloys also indicated that no changes in the composition of the surfaces had occurred. The alloys were prepared by arc melting the requisite amounts of the 99.99 pct pure elements. The four most palladium-rich alloys were remelted in a levita-tion furnace since complete melting of the components had not occurred in the arc furnace. All of the alloys were subsequently homogenized at elevated temperatures in sealed alumina thimbles. After heat treatment, the alloys were analyzed chemically and were in essential agreement with the nominal compositions. The thermal histories and nominal compositions of the alloys are given in Table I. Lattice parameters of the heat-treated alloys were computed, by means of the method described by Mueller et a1. ,I2 from X-ray diffraction powder patterns obtained with filtered copper radiation in a 114.6-mm-diam Straumanis-type Debye-Scherrer camera. The results, which are tabulated in Table I, exhibit a slightly greater negative deviation from Vegards' law than the values reported by Raub et al.13 The diffraction lines were sharp and well-resolved and thus indicated that the alloys were homogenous. RESULTS The logarithms of the individual values of the vapor pressure of palladium were fit, by the least-squares method, as a linear function of the reciprocal of the absolute temperatures. The constants of the equations are given in Table I along with the temperature range over which the data was accumulated. The latent heat of vaporization at 298.15"K for pure palladium, calculated by the third-law method,14 showed no systematic temperature dependence. The average value of 88,920 * 20 cal per g-atom agrees favorably with the average of the results obtained in the most reliable previous investigations.15"19 The activities of palladium were computed from the vapor pressure data at 1525', 1575", and 1625OK. Consistent with the mass spectrometric study of the atomicity of palladium vapor,lg the vapor was assumed to be monoatomic. The activities of rhodium were determined by integrating the Gibbs-Duhem equation with the aid of the a function.20 In the calculations, the activities of the pure solid metals were assigned the value of unity. From the activities, the partial and integral free energies, entropies, and enthalpies of formation at 1575° K were computed; they are assembled in Table 11.

Jan 1, 1969

By J. H. East, E. R. Maize

INTRODUCTION PROBABLY no other type of equipment is now being introduced into American underground mines about which less is known and about which there is more misinformation than the Diesel mine locomotive. Any equipment installed underground brings with it hazards that were not present before, and it is the purpose of this paper to show that Diesel-powered equipment can be used with safety in underground mining if certain feasible but very important precautions are taken. Diesel locomotives are not new in underground mining, since they have been used successfully in European mines for at least 19 years, but their use in American mines is exceedingly limited; so far as is known, only five Diesel mine locomotives are operating at present in United States mines. Diesel locomotives were permitted underground in Great Britain for the first time in 1939, and the rapid increase in the number in use in those mines, testifies to their safety and efficiency. More than 1300 Diesel mine locomotives are in use in European mines, according to the latest statistics; these locomotives are employed in coal, iron, lead-zinc and mercury mines. So far as is known, the Diesel mine locomotive has not yet caused an explosion or mine fire, and has not been the cause of any fatalities from toxic gases in the mines in which it has been used. ADJUSTMENTS OF DIESEL ENGINES FOR UNDERGROUND USE A Diesel engine adjusted to work in an underground mine should not be confused with the same engine adjusted for use outside the mine. Adjustment of the air:fuel ratio for engines that are used on the surface is intended to give the maximum fuel economy, and little or no attention is given to the chemical composition of the exhaust gas produced. Many such engines are poorly adjusted and perhaps poorly maintained, with the result that the engine emits smoke in quantity as well as the disagreeable odor familiarly associated with Diesel engines. The air:fuel ratio in the case of Diesel engines operated on the surface is generally around 15:1; that is, 15 lb of air to burn 1 lb of fuel. Diesel engines adjusted to work underground usually have an air:fuel ratio of about 20:I, as at this ratio the minimum quantity of toxic gases is given off in the engine exhaust. Diesel engines operated underground must be maintained in better condition than similar engines used on the surface; otherwise, the smoke emitted in the exhaust becomes objectionable if not unendurable. Practically normal air is required for safe operation of Diesel engines underground or in confined places; failure to provide virtually normal air for Diesel engine operation is almost certain to result in trouble. Bureau of Mines engineers have determined that the air in which a Diesel operates in confined places should contain less than 1/2 pct of carbon dioxide and at least 20 pct of

Jan 1, 1947

By B. F. Bush

THE coal-fields of Missouri, situated hi the northern and western portion of the State, are distributed, in whole or in part, over 57 counties, embracing an area estimated by Mr. Broad-head to be practically 23,000 sq. miles, including small detached beds and outliers in St. Louis, St. Charles, Lincoln and Warren counties in the eastern part of the State. This area includes about 8,000 sq. miles of Upper or Barren Measures, 2,000 sq. miles of exposed Middle, and 12,420 sq. miles of exposed Lower Measures. In a general way, the Missouri coal-field is bounded on the east by an imaginary line entering the northern part of the State just east of the 92c1 Meridian and passing across the State in a southwesterly direction to a point on the Kansas-Missouri line a little below the southern boundary of Barton county. An important part of the field overlaps this line and extends down the northern side of the Missouri river, under¬lying the greater part of Randolph, Howard, Boone and Audrain counties. In all, 34 counties produced coal during the year 1903. Fig. 1 shows the position of the coal-fields in Missouri. GEOLOGICAL FEATURES. The Coal Measure formations, all of the Carboniferous age, rest unconformably upon the rocks of the sub-Carboniferous or Mississippian series, and, in some cases, upon the rocks of the Devonian and Silurian ages. From their outcrop on the eastern and southeastern borders of the field, the Measures dip west to northwest at the rate of 10 ft. per mile, reaching a maximum thickness estimated by

Jan 1, 1905

By Edward P. Barrett

DURING the past few years numerous references have been made in the technical press and Bureau of Mines Bulletin 270 to sponge iron' and so-called "direct metal" processes. The idea has been prevalent that sponge iron and "direct metals" are cheap commodities. In many instances it has been proposed that these processes be used to treat low-grade ores, utilizing low-grade coals as reducing agents. It is questionable whether or not high-grade sponge iron can be made from low-grade materials. Particles contain¬ing iron oxide and gangue become, upon almost complete deoxidation, particles containing metallic' iron and gangue. The possibility of mechanically separating the metallic iron from the gangue in these particles depends . on the physical characteristics of the particular ore under treatment. Some ores, in which the minerals constituting the gangue break free from the iron oxide upon crushing, may be concentrated magnetically after the iron oxides have been reduced to metal. The finely disseminated ores are least amenable to concentration. In general, high-grade sponge iron can only be made from high-grade raw materials. Sponge iron containing small amounts of sulfur can only be made from raw materials containing small amounts of sulfur or by

Jan 1, 1930

By Glenn R. Zellars, J. P. Morris

The carrier gas method was used to measure the vapor pressure of copper over liquid copper and Fe-Cu alloys. From these results, the activity of copper in the alloys was determined at 146°, 1550°, and 1600°C. Calculations of the activity of iron were made from the results for copper. The activities of copper and iron show strong positive deviations from Raoult's law. KNOWLEDGE of vapor pressures of liquid metals has both practical and theoretical value. Fuming of metal baths is directly related to vapor pressure, and the data should bc particularly important to the technology of vacuum metallurgy. Theoretical applications include determinations of heats of vaporization, heats of solution, and activity coefficients in alloys. Methods for measuring vapor pressures of metals have been reviewed by Speiser and Spretnak.' High-vacuum procedures, such as the Langmuir and Knudsen methods, have been used most widely in recent years. However, these methods are not applicable to vapor pressures greater than lo-' mm Hg and often cannot be used in the temperature range of greatest interest. The purpose of this investigation was to develop a procedure for measuring vapor pressures of pure metals and alloys that would be applicable to pressures greater than lo-' mm Hg. The transportation or carrier gas method has been used. Copper was chosen for the initial work because its vapor pressure has been established fairly well and the reliability of the technique could be ascertained. Applicability to alloys was studied by determining the vapor pressure of copper over liquid Fe-Cu alloys. Experimental Procedure The tests were carried out in a graphite-spiral resistance furnace. The charge consisted of 50 g of metal contajned in a covered sintered-alumina crucible 1/2 in. deep and 13/8 in. ID. Two sintered-alumina tubes led from outside the furnace to within the crucible, passing through close-fitting holes in the crucible cover and radiation shield. The arrangement of the crucible and the two alumina tubes is shown in Fig. 1. The small-bore tube (1/16 in. ID by 5/16 in. OD) served as the inlet for the carrier gas. The tip of this tube touched the metal surface and the flow of gas imparted a rippling motion to the metal. In this manner the gas was brought into close contact with the metal and became saturated with metal vapor. In most of the tests the flow rate of the carrier gas was 560 ml per min, measured at room temperature. Approximately half of this saturated gas was allowed to escape from the crucible through the second alumina tube (3/16 in. ID by 5/16 in. OD) and was discharged to the atmosphere through a

Jan 1, 1957

By I. Fatt

Laboratory relative permeability data on reservoir rock are obtained on samples which are not subjected to overburden pressure during the permeability measurements. These data are then used for calculating the performance characteristics of reservoirs in which the rock is under the pressure of the overburden. Recent observations have shown that the permeability and porosity of reservoir sandstones are decreased by application of overburden pressure. These observations led us to a study of the effect of overburden pressure on the relative permeability characteristics of sandstones. A previous note from this laboratory1 showed that overburden pressure, simulated by applying hydraulic pressure to the outside of a plastic mounted core. caused a reduction in permeability of the core by as much as 50 per cent at 10,000 psig. In a multiphase fluid flow system, the relative permeability at a given saturation will change if the permeability or the effective permeability changes but not if both permeability and effective permeability change by the same ratio. The tests described in this note were made to determine the effect of overburden pressure on permeability and effective gas permeability in the gas-oil system. The gas-oil system was chosen because the available equipment was best suited for studying this system. The resultant data can be applied to other systems of interest because the gas permeability in the gas-oil system is the permeability of the nonwetting phase and, as such, is equivalent to the gas permeability in the gas-oil-water system and to the oil permeability in the oil-water system. EXPERIMENTAL METHOD Cylindrical test plugs, one in. in diameter and one in. long, were cut from sandstone core samples from three different reservoirs. After extraction in toluene, the plugs were mounted in Lucite by conventional core mounting methods.3 The core properties are given in the legend in Fig. 1. The mounted cores were machined to fit the apparatus shown in Fig 4. Air permeabilities as a function of overburden pressure were measured by connecting lines (1) and (2) to a conventional air permeameter. To measure porosity changes as a function of overburden pressure, the lines leading to (1) and (2) and the core were saturated with kerosene; line (1) was capped and a small bore precision calibrated pipet was connected to (2). Changes in pore volume of the core as overburden pressure was applied were noted by reading the amount of kerosene produced into the pipet. To correct for the change in volume of the lines inside the hydraulic cell as a function of pressure, a pressure-vs-volume run was made with a solid Lucite cylinder substituted for the core. The change in volume of the lines was about 10 per cent of the change in pore volume of the core. No correction was needed for the permeability measurements because there was no measurable pressure drop in the lines at the maximum overburden pressure. Relative gas permeabilities were measured by the stationary liquid method described by Osoba, et al.' Gas saturations were obtained by allowing the kerosene from a kerosene saturated core to evaporate out. This procedure was followed

Jan 1, 1953

By AIME AIME

PROBABLY no man has been of greater service to the Institute and has kept more in the background than Henry Krumb. A Vice-President continuously) for the last eleven years, apparently neither his picture nor a biographical sketch ever have adorned these pages and were he forewarned in the present instance he would order us to "forget it." He is a Columbia School of Mines man, Class of '98. He worked underground at Rossland, B. C. for a time, then for a year and a half a. chief engineer of the famous Camp Bird at Ouray, Colo. For three wars he was examining engineer for the Guggenheims and since 1901 has been an independent consulting engineer with experience throughout the Americas.

Jan 1, 1939

By Rufus J. Foster

During the discussion on the Preparation and Utilization of Sniall Sizes of Anthracite (page 613 of present volume), several inquiries were made concerning the use of the McClave grate, which was mentioned by Mr. Coxe as having proved satisfactory in the generation of steam at his collieries, and also at a large number of industrial estal)lishments in Scranton and elsewhere. For a more satisfactory repIy to such inquiries than could be furnished in the oral discussion, I have prepared the following paper to be included in the published proceedings. And, as the use of the fuel under consideration necessarily requires the employment of a blower to change the fire, from a condition giving an incandescent radiant heat only to one giving a hot gaseoua flame as well, I shall add a description of the McClave Argand blower and its method of action. The grate and blower combined form a complete and effective system fcr burning small fuels, such as anthracite culm, birdseye, buckwheat, bituminous slack, etc., in boiler and other furnaces; while the grate alone is now extensively used with the larger sizes of hard and soft coal in furnaces where blast is riot required. Fig. 1 is a view of the RlcClave grate as built in two sections. It is constructed on the principle best approved by practice to prevent warping and burning out; that is, it presents no long lines of

Jan 1, 1892

By R. A. Graham, R. W. Rohde

The effect of hydrostatic pressure upon the austenite start temperature of a commercial Fe-28.4 at. pct Ni-0.5 at. pct C alloy has been determined. For pressures to 20 kbar, the austenite start temperature decreased from its atmospheric pressure value of 380°C at the rate of about 4°C per kbar. These data are analyzed by two different thermodynamic approaches; first, considering the transformation as an isothermal process, and second, considering the transformation as an isentropic process. It was found that both these approaches fit the experimental data equally well. The effect of hydrostatic pressure upon the austenite start temperature is best described by considering the mechanical work done during the transformation as that work obtained by multiplying the applied pressure with the gross volume change of the transformation. It is widely recognized1 that strain has an important effect on the initiation of martensitic transformations.* For example, the martensite start tempera- *In this paper, use of the term martensitic transformation implies the reversal of martensite to austenite as wen as the formation of martensite from austenite. ture, M,, may be increased by plastic deformation. Similarly, plastic deformation is observed to lower the austenite start temperature, A,. The effect of uniaxial stress on the M, of iron-nickel alloys has been studied by Kulin, Cohen, and Averbach.2 They found that the martensite start temperature was significantly changed by stresses well within the elastic region. Moreover, the effect of tensile and compres-sive stresses differed. These effects were explained in terms of the interaction of the applied stress with both the dilational and shear components of the transformation strain. The magnitudes of the influence of uniaxial tension, compression and hydrostatic pressure on Ms were measured in 30 pct Ni 70 pct Fe by Pate1 and Cohen.3 Their thermodynamic calculations and similar calculations by Fisher and Turnbull4 predicted the experimental results when the transformation was assumed to occur isothermally at some fixed driving force. This driving force was assumed to be supplied by a combination of the chemical free energy difference between the austenitic and martensitic phases and the work performed during transformation by the applied stress. More recently, Russell and winchel15 reported the effect of rapidly applied shear stress on the reversal of martensite to austenite in iron-nickel-carbon alloys. They performed a thermodynamic analysis of this transformation based upon the assumption that the re- versal occurred adiabatically. They concluded that the applied shear stress did not significantly interact with the transformation strain and thus did not assist in inducing the reversal. Rather they concluded that the reversal was effected by localized strain heating which resulted from the gross local shear deformation of the experiment. In either the adiabatic or isothermal analysis it is necessary to compute the work performed by the interaction of the applied stress and the transformation strains. In the case of hydrostatic pressure this interaction has been treated by two different methods. In either case the applied pressure is assumed to remain constant during the transformation. In one treatment the applied pressure is assumed to interact directly with the dilatational strain associated with the formation of an individual martensite plate.3'4 This local strain has been measured at atmospheric pressure in iron-nickel alloys by Machlin and Cohen.6 In the above treatment this local strain is assumed invariant with temperature and pressure changes. In the other treatment the applied pressure is assumed to interact with the gross volume change of the transformation.7,8 The usefulness of this latter treatment has been demonstrated by Kaufman, Leyenaar, and Harvey7 who calculated the effects of pressure upon the martensite and austenite start temperatures of Fe-10 at. pct Ni and Fe-25 at. pct Ni alloys. Excellent agreement was obtained between their calculations and their experimental data on an Fe-9.5 at. pct Ni alloy. However, this treatment suffers from the fact that the data required to calculate the volume change of the transformation (i.e., the initial specific volumes, the thermal expansion and compressibility data for both the austenitic and martensitic phases) is, in general, not available for any material except pure iron. Thus the calculations of Kaufman et al.7 were necessarily performed by assuming that the volume change of the martensitic transformation in the iron-nickel alloys was that same volume change occurring during the a-? transformation in pure iron. While this approximation may suffice for very dilute alloys it is likely to be inaccurate in high nickel alloys. We have performed measurements of the effect of hydrostatic pressure to 20 kbar on the A, temperature of an Fe-28.4 at. pct Ni-0.5 at. pct C alloy. The composition is similar to the alloy used by Pate1 and Cohen3 to determine the effect of pressure upon the M, temperature. The present measurements permit calculation of the interaction between the applied pressure and the transformation strain. Additionally, measurements have been made which allow precise determination of the gross volume change of the transformation. The data allow direct comparison between the alternate hypotheses of the interaction between the applied pressure and a dilatational transformation strain characterized by either the formation

Jan 1, 1970

By Walter G. Perkins

As this particular product holds a place by itself, it seems desirable to give a paper dealing especially with it as a corollary to my paper entitled " The Litharge Process of Assaying Copper-Bearing Ores and Products, and the Method of Calculating Charges."* The process is first to convert the metallic copper into matte by the addition of sulphur, allowing the two elements to combine at the bottom of the crucible when heat is applied. The

Jan 1, 1903

By P. Wynblatt, J. E. Dorn

The effect of strain rate, temperature, and interstitial impurity concentration on the flow stress was investigated in a poly crystalline Fe-2 pct Mn alloy. The temperature dependence of the flow stress was found to be independent of the interstitial impurity concentration, removal of interstitials merely decreasing the atherma1 stress level. Below 160%, the large temperature dependence of the flow stress was interpreted in terms of the Dorn-Rajnak theory of the Peierls mechanism of plastic deformation. Above 160"K, some other thermally activated intrinsic meckanisln seems to be operating. The strong temperature dependence of the flow stress of bcc iron at low temperatures has been studied by numerous investigators and interpreted in terms of several different thermally activated dislocation mechanisms. The following mechanisms have been proposed: a) interaction of dislocations with interstitial impurity atoms1 or with solute atoms in general; b) interaction of dislocations with clusters of impurity atoms;3 c) resistance to the motion of dislocations due to jogs on screw dislocations;* d) resistance to the motion of dislocations due to the Snoeck effect;' and e) interaction of dislocations with the intrinsic resistance of the bcc lattice or Peierls "hills". In previous work: it was found that the plastic behavior of polycrystalline iron containing 2 wt pct Mn (and 100 ppm C + N) is in good agreement with predictions based on the Peierls mechanismlo from 77" to 160°K whereas from 160" to about 370°K another as yet unidentified thermally activated mechanism is operative. The purpose of the present investigation was to determine the effect of interstitial impurities on the temperature dependence of the flow stress, by purifying the previously investigated alloy with respect to interstitial impurities. The investigation revealed that removal of the interstitial impurities to a level that eliminated Cottrell locking and the Portevin-LeChatelier effect (i.e., serrations in the stress-strain curve due to dynamic strain aging) affects neither the strong temperature dependence of the flow stress at low temperatures nor the general characteristics of the higher-temperature behavior. Such purification, however, lowered the athermal yield stress. I) EXPERIMENTAL PROCEDURE AND RESULTS The material used in this investigation consisted of an Fe-2 wt pct Mn alloy having the following additional elements present: 0.004 pct C, 0.006 pct N, 0.05 pct 0, 0.004 pct S, 0.003 pct P, and 0.001 pct Si. This was the same material as that studied in the previous investigation and will henceforth be referred to as the "impure material". The as received -jr by 2 in. hot-rolled bars were cold-rolled to 0.08-in. thickness, recrys-tallized under argon for 30 min at 80O0C, and further cold-rolled to 0.053-in. thickness. Flat tensile specimens 3 in. wide having a 1.625-in.-long gage section were machined from the sheet and then purified. The first stage of purification consisted of holding the specimens at 850°C for 24 hr in a stream of hydrogen saturated with water vapor at room temperature. Material prepared in this fashion will subsequently be referred to as "wet hydrogen purified material". It has been estimated that this type of treatment reduces the carbon content of iron to less than 5 ppm.' The second stage of purification consisted of holding the specimens in a closed system through which hydrogen was circulated past the heated specimens as well as a zirconium hydride getter. The specimens were held at 850°C and the getter at 800°C. The process was continued for 212 hr. The starting material for this process was wet hydrogen purified material. Material prepared in this manner will be referred to as "ZrHz purified material". The technique used was substantially the same as that described by Stein et al.' who have shown that the carbon level at the end of the process is reduced to about 5 parts per billion. The mean grain size of the three materials was found to be -60 C( for the impure material and -160p for the wet hydrogen and ZrHz purified materials. All tensile testing was carried out on an Instron Testing Machine either in controlled-temperature baths or at fixed-point baths such as boiling liquid nitrogen, and so forth. When fixed points were used the temperature was kept constant to better than *1°C whereas in all other tests the temperature variation was less than *2°C. Test of Purity. It was not possible to determine the purity achieved at each stage of the purification because the resulting level of interstitial impurities was near or below the limit of sensitivity of standard analytical techniques. It was possible, however, to obtain a qualitative measure of the extent of purification from the appearance of the stress-strain curves for the three materials. Fig. 1 shows the stress-strain curves for the three different materials tested at 300°K. It can be seen that the effect of wet hydrogen

Jan 1, 1967

By Arnulf Muan

PHASE relations in three isothermal sections (l000°, 1100°, 1200°C) of the system Ag-Fe-Pd have been determined as part of a program to develop improved crucible materials for containing low-melting iron silicates at low oxygen potentials. The following experimental method was used: Two- to 3- g samples of each of forty different alloys within the system Ag-Fe-Pd were made up from metals of 99.9 pct purity. The mixed metal powders were contained in a 1-cc crucible of dense recrystal-lized alumina and heated in a protective atmosphere (90 vol pct A, 10 vol pct H2), first to complete melting for approximately 30 min and subsequently at the desired equilibration temperature (1000°, 1100°, or 1200°C) for approximately 24 hr. The samples were then quenched rapidly to room temperature and examined metallographically as well as by X-ray techniques. Unit cell dimensions were compared with standards obtained by study of one-phase alloys of known compositions. The results are summarized in diagrams (a), (b), and (c) shown in Fig. 1. Heavy solid curves outline areas comprising compositions of mixtures consisting of the phases labeled for each area. Mixtures in which liquid is the only condensed phase present are confined to very narrow areas adjacent to the Ag-Pd join at high silver contents. An enlarged, distorted picture of the phase relations prevailing in these areas is shown in the upper-left circular insert. Particular attention is directed toward the misci-bility gap which occupies major parts of the composi-

Jan 1, 1962

By GORDON H. FISHER

During the year 1945, the drilling pace in West Texas increased above that in the year 1944, and represented the highest number of well completions since 2941. The 1680 new wells drilled 8,287,958 ft. of hole for a per well average of 4933 ft. This depth is approximately 30o. ft. deeper than the average for the year 1944. Although the deepest well drilled in West Texas (Phillips Petroleum Company's Ada Price No. 1, in Pecos County) was completed during the year. 1944 to a depth of 15,279 ft. and tested the Ellen-burger horizon, the producing depth record for West Texas was set during the year 1945 with the completion of Amerada Petroleum Corporation's Jones No. I-A, in the Jones Ranch field, Gaines County, which now is producing at 11,422 ft. from the Devonian formation.

Jan 1, 1946