Search Documents

By H. R. Peiffer

Hardening of soft metals can be accomplished by dispersing finely divided hard particles in them. The dispersing of finely divided alumina in silver in the presence of oxygen yields a high strength material which is unusual in that its mechanical properties above the melting point of the continuous Ag-O alloy matrix are similar to other solids. The tensile strength is studied for two of these alloys, one of which contains 15 pct by weight alumina and the other 20 pct by weight alumina. The average fracture strengths above 960°C of these alloys were found to be 0.4 x106 dynes per sq cm and 3.8x106 dynes per sq cm respectively. The strengths appenred to be independent of temperature above 960° C. The creep behavior of the 20 pct alumina material was studied above 960°C. The initial creep rate, 6 , of this material can be represented by where s is the applied stress and E the activation energy for the process. This energy is of the order of 1.7 to 2.1 ev. HARDENING of soft metals by the addition of finely divided, hard particles has resulted in the production of materials with excellent creep resistance and with inhibited recrystallization.' It has been demonstrated that such composites have useful strength up to temperatures very near the melting point of the soft metals, but one might expect that the strengthening by the dispersed particles ceases to be of importance above the melting point of the softer phase. This, however, is not so.2 In this paper the strengthening of a liquid Ag-O solution by the presence of dispersed alumina is discussed and experimental data concerning the mechanical properties of such a material at temperatures above 960°C presented. EXPERIMENTAL PROCEDURE Specimens were prepared using powder metallurgical techniques. Finely divided silver oxide was mixed in the appropriate proportions with "Linde B" alumina. For these experiments the specimens contained 15 or 20 wt pct alumina in pure silver.* These alloys were used in these experiments since they were the ones that could be handled readily enough to yield experimental data. Silver oxide was used in preference to silver because it is readily available in a very finely divided form and because the presence of excess oxygen in the silver is important to the properties2 of the material. The powders were mixed wet, using alcohol as the medium, in an ordinary food blender until a uniform mixture was obtained. They were then dried and heated to reduce the silver oxide to silver. Only a fraction of the finely divided silver remains unoxi-dized upon removal from the oven since the finest particles of silver oxidize immediately upon contact with air. The remaining fine silver served as a binder during pressing. The mixture was then pressed at 20 tons per sq in. into shoulder-grip (reduced section 1/4 in. by l/4 in. by 1 1/4 in.) and rectangular bar specimens (l/4 in. by 1/4 in. by 2 in.). The green specimens were heated very rapidly in a globar furnace to 1000°C, held at temperature untic they had reached theoretical density and then furnace cooled. The strength of the two compositions at temperatures above 960 °C was determined by pulling shoulder grip specimens inside a furnace mounted on a tensile machine. Specimens were gripped by means of wires wrapped around the shoulders of the specimen. Temperatures were measured by means of a chro-mel-alumel thermo-couple placed in the vicinity of the specimen. Control of temperature (within ±°15C) was accomplished by means of a Weston Recorder-Controller. Before loading, specimens were held at temperature for approximately 15 min in order to insure uniform specimen temperature. The low loads were measured by a special load cell designed by Baldwin Lima Hamilton. All testing was performed on a FGT testing machine of the same com-pany. Creep studies were performed in bending utilizing rectangular specimens of the 20 pct alumina alloy. Specimens supported at both ends by knife edges of inconel were placed in a globar furnace, heated quickly to temperature, and the deflection of the beam measured optically as a function of time. The weight and size of the specimen were predetermined and the maximum stress on the beam calculated from

Jan 1, 1962

By B. S. Tani, R. V. Schablaske, M. G. Chasanov

In the Ti-Cd system two intermediate phases, TiCd and Ti Cd, have been found and characterized by X-ray diffraction powder techniques. An earlier reference' had reported the existence of the compound Tisd. No structural details, however, were given nor was there any indication of the possible existence of other binary compounds. Studies of the solubility of titanium in liquid cadmium2 led to the discovery of both TiCd and Tisd. The solid phase in equilibrium with saturated solutions of titanium in liquid cadmium at temperatures below 620°C is TiCd, whereas TizCd is the equilibrium solid phase above 620°C. Both thermal analysis and X-ray studies show that a peritectic reaction between the y phase (~isd) and cadmium to form the 6 phase (Ti Cd) occurs at 620°C. X-ray diffraction powder photographs of material isolated from the ingots used in the solubility measurements as well as material prepared by a direct heat of the appropriate stoichiometric amounts of titanium and cadmium can be indexed on the basis of a tetragonal unit cell with a = 2.904 ± 0.002A, co = 8.954 * 0.004A, c/a = 3.083. No variation of lattice parameters indicative of a range of composition is evident. With four atoms in the unit cell the calculated density of the intermetallic is 7.05 g per cm3; the observed value is 7.07 g per cm3. The TiCd lattice is primitive as indicated by the fact that there are no systematic absences among hkl reflections. The absence of all hko reflections for which h + k = 2n + 1 is also evident. This systematic absence indicates the following two space groups, C\h — P4/n and D&~4/nmm; both groups, however, have the same two- and four-fold positions. Stoichiometry, symmetry and space group indicate two likely structure types. They are the PbO-litharge3 (B10) type and the Ti CU (B11) type. Spatial considerations favor the B11 structure with atoms placed in the following positions: 2Ti (c) 0, 1/2, Z; l/2, 0, Z 2Cd(c) 0, 1/2, Z; 1/2, 0, Z The TiCd structure may be summarily described as a layered structure in which double cadmium layers alternate with double titanium layers along the c-axis. The best agreement between calculated and observed intensities is obtained for the values ZTi = 0.608 and ZCd = 0.130. Calculated and observed powder intensities as well as other pertinent powder data are recorded in Table I. Interatomic distances for the proposed structure are recorded in Table II and are to be compared with the distances of closest approach for titanium and cad-

Jan 1, 1962

By AIME AIME

Report of Committee 24, of the International Association for Testing Materials, presented at the Brussels Congress, 1906. Republished for use at the 94th Meeting of the American Institute of Mining Engineers, New York, N. Y., February, 1908. Discussion by letter is requested by the Secretary of the Institute. The Committee appointed for the solution of Problem 24 consisted of the following members Prof. H. M. Howe, New York, N. Y. (Chairman); L. Levy, Paris, France (Vice-Chairman) ; Prof. D. Tschernoff, St. Petersburg, Russia (Vice-Chairman) ; Prof. Albert Sauveur, Cambridge, Mass. (Secretary) ; Van Drunen, Ixelles, Belgium; Lieut.-Col. H. Tusen, Copenhagen, Denmark ; E. P. Martin, Abergavenny, England ; A. Pourcel, Paris, France ; H. Brauer, Dortmund, Germany ; Dr. Prof. H. Wedding, Berlin, Germany; P. Verole, Milan, Italy ; A. Baalsrud, Christiania, Norway ; A. R. v. Dormus, Vienna, Austria ; A. Sailler, Vienna, Austria; Bureau des Forges, St. Petersburg, Russia; Prof. N. Belelub-sky, St. Petersburg, Russia ; N. Jossa, St. Petersburg, Russia ; Maj.-Gen. M. Korobkoff, St. Petersburg, Russia ; S. Smirnoff, St. Petersburg, Russia ;.Ladislaus v. Tetmajer, Budapest, Hungary ; H. H. Campbell, Steelton, Pa. Early in February, 1905, a list of species and varieties of iron and steel, with definitions, drawn by the Chairman and Secretary of Committee 24, was sent to every member of this Committee with a request for comments and suggestions. A special request was sent to the following gentlemen . for the equivalents in their several languages of these species and varieties : A. , Pourcel, Paris, France; Prof. H. Wedding, Berlin, Germany ; J. A. Brinell, Stockholm, Sweden ; Prof. H. I. Hannover, Copenhagen, Denmark; Prof. P. Kley, Delft, Holland; P. Verole, Milan, Italy; Col. Cubillo, Trubia, Spain. This present report, which is based upon our original list and definitions, and upon the replies to these requests, consists of four parts I. A polyglot, which gives the names of the chief classes of iron and steel in English, French, German, Swedish, Danish and Dutch. We .regret that we have failed to get the Italian and Spanish names. II. English definitions of principal classes of iron and steel. III. A glossary of special sizes and shapes of iron and steel. IV. A note on the boundary between steel and cast-iron. I. POLYGLOT, IN ENGLISH, FRENCH, GERMAN, SWEDISH, DANISH AND DUTCH, OF THE CHIEF CLASSES OF IRON AND STEEL, AND OF THE APPARATUS IN WHICH THEY ARE MADE. This list is not intended to be complete, but rather to include only those varieties which are of interest to the Association.

Mar 1, 1908

By R. S. Shoemaker, F. W. McQuiston

MAGMA COPPER COMPANY San Manuel Division The San Manuel Division of Magma Copper Company is located about 40 miles north of Tucson. Tons of ore milled in 1973 .were approximately 19 million at a rate of 63,000 tons per day. From this, about 42,600 tons of copper concentrate was produced as saying approximately 1.070 MoS2 and 28.5% Cu. As with many copper ores, the San Manuel ore contains a small amount of gold, but in this particular case, much of the gold follows the molybdenite. Separation of the molybdenite from the bulk sulfide concentrate by flotation produces a moly concentrate containing 9170 MoS2, just under 1.070 Cu, and 0.44 oz Au per ton. Cyanidation of this material for gold recovery is the only practice of its kind known to the authors of this Monograph. After thickening, the final moly concentrate is filtered for subsequent repulping with cyanide and lime. Gold dissolution takes place in three agitators in series with the pulp from the agitators being filtered in two stages in disc filters. Between filtration stages, the cake is repulped with barren solution. Filtrate from both filters is the pregnant solution. The Merrill-Crowe recovery unit is comprised of two solution tanks and the usual clarifying filter, vacuum tower, zinc dust feeder and Merrill precipitate press. Because of the presence of finely divided sooty chalcocite in the molybdenum concentrate, the cyanide consumption of 55 pounds per ton is extremely high. A compensating factor, however, is the low copper, moly concentrate produced. Precipitation of the gold from the highly copper-contaminated solution requires 0.56 pounds of zinc dust and 0.28 pounds of lead acetate per ton, high figures when compared to normal cyanidation practice. The Merrill- Crowe precipitate assays approximately 28.5% Cu, 8% Zn, 156 oz Au and 197 oz Ag per ton. The San Manuel cyanidation plant is an outstanding and innovative development.

Jan 1, 1975

By E. S. Tankins, G. R. Belton

A simple solution model, based upon the formation of molecular species, is developed for strongly electronegative dilute solutes in liquid binary-metallic solvents. Two approximations are considered for the relative concentrations of the species: the random and the quasi-chemical. Equations are presented for the partial molar free energy, enthalpy, and entropy of mixing of the solute. An experimental study has been made of equilibrium in the reaction H2 6) +0 (dissolved) = H2O(g))for the liquid Cu-Co alloys. The standard free energy of solution of oxygen is presented as a function of composition for the alloys at 1550°C and as a function of temperature for five of the alloys. The experimental results for these alloys and also for Cu-Ni alloys are shown to be in reasonable agreernent with the theory in the random approximation. A knowledge of the thermodynamic behavior of dilute solutes in liquid metals and alloys is of importance in understanding and designing refining and alloy-making processes. Accordingly, several attempts have been made to derive suitable solution models to forecast the effect of a third component on the activity coefficient of such a solute in a metal. Alcock and Richardson' reviewed the literature prior to 1958 and also showed that a regular solution model gave a reasonable description in the case of metallic solutes but failed to account for the behavior of the more electronegative solutes sulfur and oxygen. These same authors2 later modified their model by using the quasi-chemical approximation3 to calculate the average composition of the first coordination shell surrounding each solute atom. This modified model was shown to lead to a better qualitative description of the behavior of the electronegative solutes; however, quantitative agreement with experimental data for oxygen in alloys could only be achieved by assuming a very small coordination number. The authors concluded that the major source of error in the model was the assumption that pairwise interaction energies were independent of composition. Substitutional and interstitial random solution models by Wada and saito4 are essentially similar to the first model except that the required interchange energies were derived from the modified solubility parameter equation of Mott, instead of from experimental binary data. Most recently Hoch5 has presented a statistical model for interstitial solutions and has applied the model to the Fe-C-O system. However, as the various interaction energies needed in the model had to be derived from the ternary data, the model does not promise well as a means of forecasting ternary behavior. Each of the above models carries the assumption that the strongly electronegative solutes have the same configurational environment as metallic solutes; i.e., the solute can be treated as a substitutional or interstitial atom in a quasi-crystalline lattice and is surrounded by a normal coordination shell of solvent atoms. There are, however, a number of facts which suggest that this is unlikely. First, the heats of solution are large, being more typical of molecule formation rather than alloying. For example, the heats of solution of monatomic oxygen and sulfur in liquid iron are -90 kea16,8 and -74 kea1,7, 8 respectively. These are to be compared with maximum heats of solution of metallic solutes in liquid iron of about -13 keal (silicon is an exception with -28.5 kea17). The large depression of the surface tension of liquid iron by trace amounts of the electronegative solutes oxygen, sulfur, and selenium9 suggests, by analogy with aqueous systems, the possible existence of polar molecules in the liquid. The effect of these solutes is at least three orders of magnitude greater than normal metal solutes.10 As has been pointed out by Richardson,11 the electron affinities and ionization potentials of oxygen and sulfur are such that it is likely that they exist in metallic solution as negatively charged ions. If this is so, and it is assumed that electrostatic forces play an important role in determining the configuration, it is unlikely that the stable configuration will be that of an isolated ion surrounded by a symmetrical coordination shell of solvent ions. It is more likely that the energy of the system would be lowered by the formation of solute-solvent screened dipoles. The above arguments suggest the formation of "molecular species" between solute and solvent atoms. The idea of the existence of molecular species in such solutions is not new, however', for Marshall and chipman12 have explained in a semi-quantitative manner the C-O equilibrium in liquid iron by postulating the species CO. Chen and Chip-man13 interpreted their measurements on the Cr-O equilibrium in iron in terms of the species CrO. Zapffe and sims14 have also postulated the existence of such species in liquid-iron alloys.

Jan 1, 1965

By Walter Miller

ALTHOUGH confident of its ability to meet any demands which may be made, the petroleum refining industry is not complacent about the situation and realizes that the quantities of petroleum products to be furnished are so enormous and so far beyond what was previously estimated that the full co-operative effort of the industry must be exerted. Establishment by the President in May of the Office of Petroleum Coordinator for Defense with Secretary of the Interior Ickes at its head, plus the formation of the Petroleum Industry Council for Defense, in November, provide the channels for united endeavor within the industry and the means for gearing that endeavor within the industry and the means for gearing that endeavor in full harmony with the nation?s needs. Great strides have been made and a rapid understanding of the situation and the magnitude of the task is being attained by all concerned.

Jan 1, 1942

M. AlbERtson, Chairman. Production Engineer, Shell Petroleum Corporation, Houston, Texas. R. P. McLaughlin, Associate Chairman. General Manager, Burnham Exploration Co., Los Angeles, Calif. Eugene A. Stephenson, Secretary-Treasurer. Professor of Petroleum Engineermg, Missouri School of Mines and Metallurgy, Rolla, Mo. Ezecutive Commillee M. Albertson, Chairman. C. E. Beecher, Empire Oil & Refining Co., Bartlesville, Okla. L. L. Foley, Petroleum Engineer and Geologist, Tulsa, Okla. R. B. Kelly, Division Manager, Pure Oil Co., Fort Worth, Texas. Hallan N. Marsh, Production Engineer, General Petroleum Corporation of California, Los Angeles, Calif. R. E. Somers, Geologist, The Gulf Companies, Pittsburgh, Pa. Production Engineering T. V. Moore, Vice-chairman. Charge Production Research Division, Technical Service and Development Dept., Humble Oil & Refining Co., Houston, Texas. Joseph Chalmers. De Bataafsche Pet. Maatschappij, The Hague, Netherlands. M. L. Haider, Petroleum Engineer, Carter Oil Co., Tulsa, Okla. Emile HUGUENIN, Deputy State Oil and Gas Supervisor, Los Angeles, Calif. Carl E. Reistle, Jr., Petroleum Engineering Dept. Humble Oil & Refining CO., Houston. Texas. Produclion J. Terry DUCE, Vice-chairman. Geologist, The Texas Company, New York, N. Y. Basil B. Zavoico, Associate Vice-chairman. Consulting Geologist, Houston, Texas. Engineering Research R. L. Huntington, Vice-chairman. Associate Professor, Petroleum Engineering, University of Oklahoma, Norman Okla. Economics Sidney A. Swensrud, Vice-chairman. Assistant to the President, Standard Oil CO., Cleveland, Ohio. Refinery Engineering Walter Miller, Vice-chairman. Vice-president, Continental Oil Co., Ponca City, Okla.

Jan 1, 1937

NOW continuing with the preparation of the moulds I say that it is necessary to give the greatest attention to the differences of the clays as well as to the differences of those things that you wish to mould; and to know that every concavity in the mould produces a convexity and every convexity a hollow following the shape of the original pattern that you have. The pattern should be a body of a harder mated than the thing [78] you wish to mould with and of a substance that is not swollen or disintegrated by moisture. Its archetype may be of marble, bronze, lead, or any other metal, or also of wood, wax, tallow, gypsum, sulphur, or other plaster compositions-in short, of whatever you may have or whatever succeeds best for you, depending on whether the works are large or small and easy or &cult to mould. If you wish to cast them in bronze, you must mould them with loam, covering them with it and then drying it. There are some things in which it is enough to form only one part, such as half- or bas-reliefs. These are easy if they have no undercuts. Some other patterns that are easily handled are formed in two halves, or in three or four pieces, if they are of a hard material. There are also moulds for large statues, which, if one desires to make them of bronze, are first made of wax according to the ordinary procedure. I have in mind to describe every one of these processes in their own place. There are like- wise some moulds that are difficult to make, like scenes on a plane to which figures in full relief are attached, or twisted ornaments or other detached things that cannot be withdrawn from the mould without break-

Jan 1, 1942

By R. D. Gibbs, C. C. Taylor

The gas-lift, or circulation of gas for the production of crude oil, now includes the gas operator in field production activities to a greater extent than ever before. It is the purpose of this paper to show the scope of his activities and to discuss the various means of handling and treating the large quantities of gas which are now of a somewhat different nature than formerly. The extent of the stripping action of circulating gas on oil must be discussed, as this can be governed somewhat by the method of treatment of the recirculated gas. Change in Gas-decline Curve under Circulation Before the advent of the gas-lift, the gas-production curve of a field showed a peak during the flush production with a rapid decline as the wells were put on the pump and then a long steady decline curve of a relatively small volume of rich gas for the life of the field. Under the gas-lift method of production, instead of having the sharp decline at the end of the flush production period, sufficient circulating gas to keep up the required total gas-oil ratio would be turned to the wells. The gas-production curve then assumes a long gradual decline, giving a large volume of gas for treatment for several years to come. The gas-decline curve will not follow that of the oil, as the lowering of the rock pressure by the steady production of oil and gas from the sand will make it necessary to continue using the large tubing and to circulate large volumes of gas in order to keep the back-pressure against the sands as low as possible. A Complicated Distributing System In tracing the flow of the gas from the time it leaves the well until it again enters through the casinghead, under high pressure, we get a very good idea of the complex distributing and regulating system that must be installed and the large treating and compression plants that are necessary (see Fig. I). Gas traps must be large enough to efficiently separate large quantities of gas and oil and should be elevated sufficiently to enable the oil, if

Jan 1, 1928

By Hannon, J. W. G.

Silicosis is today's most important industrial disease and probably dates back to the Stone Age. Since the industrial revolution, increasing attention has been paid to those occupations where mineral dust is present in the air breathed by the workers. For many years it was assumed that the inhalation of all mineral dusts was hazardous. but investigations conducted in several countries pointed the statistical finger of guilt at free silica in any of its numerous physical forms as a dust of outstanding toxicity. Recognition of silica as the chief hazard has resulted in widespread use of the term "silicosis." Depending upon the concentration of finely divided silica dust to which the individual is exposed and the duration of exposure, silicosis may become a disabling condition in from one to thirty years. The structure of the lung and respiratory passages is such that only minute particles of silica can gain entry to the air cells in the lung (5 microns or under are most toxic). When these minute particles gain entry to the lung tissues they stimulate certain protective cells in the lung to multiply at an excessive rate. The cell's undergo inflammatory changes which result in nodular scars and a low-grade inflammation of the lung tissue. These progressive changes in the lung structure gradually encroach

Jan 1, 1949

By Williams, J. A.

THE Alaska Juneau mine has been developed through an adit driven at the elevation of the top of the mill and all mining is done above this main haulage level. As a result of wholesa1e"mining operations about 11,000 tons rock containing one dollar' per ton in gold is, hauled to the. concentrator during every 24 hr. Due to the method of mining, whereby a system of oreways delivers-the.ore direct from the stope to the bottom level of the mine, no tramming of ore is done on any of the upper levels. However, ;in doing exploratory drifting and crosscutting on the upper levels, the broken material is trammed by hand in 1-ton 18-in. gage cars to a nearby raise connecting with one of the several oreways. This constitutes the only tramming operation except that on the main level.

Jan 1, 1931

By W. M. Parris, P. D. Frost, H. A. Robinson

The effects of hydrogen content and strain rate on the static tensile and notch-rupture properties of the Ti-3Mn-complex alloy heat-treated to differed strength levels were investigated. The extent of embriulement was found to be proportional to the amount of hydrogen present and the strength to which the specimens were heat-treated. The research suggests the possible necessity of specifying lower hydrogen limits than are now allowed when titanium alloys are heat-treated to higher strengths than are presently used. The research also supports a hypothesis advanced earlier for a mechanism of hydrogen embrittlement. MUCH attention has been focused on the effects of hydrogen in in Most of the published in- formation has dealt with the effects of hydrogen on alloys in the annealed or lowest-strength condition. The work of Kotfila and Erbin3 is one of the few exceptions. In view of the fact that heat-treatments are now being used to produce high strength in titanium alloys,' it is necessary that more attention be given to the effects of hydrogen on these alloys in the heat-treated condition. Research was initiated to establish the effects of hydrogen on the properties of the Ti-3Mn-complex alloy at various strength levels. This research, which supplemented that of Kotfila and Erbin, was started because it was found that high-strength tensile specimens of this alloy were strain-rate sensitive. The essential results of the research are summarized in this paper. MATERIALS AND EXPERIMENTAL PROCEDURES Material for this investigation was a 41/2-in.-diam bar forged from a single commercial heat of the Ti-3Mn-complex alloy having the composition given in Table I. The as-received forging was reduced further by forging at 1750°F to 3/4-in. square bars. About one fourth of this material was vacuum annealed at 1400°F for 24 hr to obtain a base hydrogen content of 25 ppm. The remaining bars were hydrogenated to levels of 90, 140, and 260 ppm in a large Sievert's apparatus in the following manner: Four 3/4-in. square bars, 5 in. long, were placed in the reaction chambzr. The chamber was evacuated, heated to 1400°F, and a measured amount of hydrogen was introduced. When absorbtion was complete, as indicated by the drop in pressure, the reaction tube was cooled and the bars removed. Each batch of bars was then sealed in individual evacuated Vycor containers and heated for 24 hr at 1400°F in order to distribute the hydrogen homogeneously. After vacuum-annealing or hydroge nation, the bars were rolled at a temperature (1400°F) below the ß-transus to 1/2 - in. - diam rounds. Groups of the rolled specimens representing each of the hydrogen levels were given the following heat-treatments: 1) One hr at 1300°F, water-quenched. 2) One hr at 1300°F, water-quenched, and aged 8 hr at 1100°F. 3) One hr at 1300°F, water-quenched, and aged 4 hr at 1000°F. 4) One hr at 1300°F, water-quenched, and aged 48hr at 800°F. Heat-treated bars were machined into standard 0.250-in.-diam tensile specimens having 1-in. gage lengths. Throughout the processing and testing of this material, hydrogen analyses were made by vacuum-fusion methods to check for accuracy of hydrogen additions, homogeneity, and possible losses during processing. A summary of these analyses is given in Table II It may be seen that the actual hydrogen contents were reasonably close to the desired levels. In addition, it was noted that the variation in hydrogen content within any one bar did not exceed

Jan 1, 1959

By W. Henry Weimer

A successful surface coal operation requires the combined efforts of engineering and operating personnel. In the planning for a mine, machines should be selected to do the best work in getting the coal uncovered, loaded, and transported to the preparation plant. The best system and extent of cleaning will be determined by the market. After the fundamentals of operation have been established, the operating personnel should see they are carried out. There is no simple solution to some of the every day problems facing the operating officials. Here the production engineer with the technical approach, time studies, control methods, past experience, and available records can help in detecting causes of inefficient phases of the operations. With these studies, a careful analysis can be made in setting up the expected standards to be followed. Management can then compare the job under study with the standards and make corrections to solve the problems. 5.2-1. Annual or Daily Coal Production. Once the production cycle has been established, it is paramount that coal sales keep the productivity of the mine as high as possible. A successful company does this by what they call "the control approach." The daily tonnage report is one of the things that is a potent control tool in attaining the goals to be achieved. If production is falling short of the goal, the daily tonnage report will reveal what has to be done in the remaining days of the month or year to achieve the expected schedule. When goals are reached or exceeded, then budgeted tonnages and costs will be reached or exceeded and thus assure attainment of a profit. Failing to keep to the scheduled pace shows up quickly and prominently, facilitating any necessary action to get things back to the projected plans. The sales target is usually set a little higher than the operating production. The sales tonnage is scheduled and sales are made accordingly, slightly

Jan 1, 1968

By A. B. Parsons

LECTURE, it appears, is a discourse that is supposed to be instructive. I am quite sure that you will derive no instruction from what I have to say. I will be satisfied if my remarks provoke thought along one or two mental paths that have not been traveled so fre¬quently as to be devoid of interest. I have no particular message apropos of professional engineers or professional engineering, and any conclusions that I may seem to reach will be purely tentative and incidental. Probably at times you have wondered, in a casual way at least, why so many people who are not, never have been, and never will be engineers, want to use the title. For example, I recently received a communication from a life insurance broker or salesman, whose chaste letterhead bore the legend "Estate Engineer." He was perfectly serious about it, as is also the expert accountant who assumes the imposing name of cost-analysis engineer. Dozens of equally amazing titles might be cited. Then there is that class of individuals who have been engineers, in the true sense of the word; who have gone into some other kind of occupation; but who cling tenaciously to the name engineer, usually prefixing some word or other which at once gives them away by telling what their work really is. For example, we have such pseudomorphs as the management engineer, and the sales engineer. It is quite evident that engineer is a word to conjure with. Evidently both the man who appro¬priates the designation without any justification and the ex-engineer who persists in calling himself an engineer even after he has abandoned engineer-

Jan 1, 1933

By Eric S. Cheney

Sulfur isotopes are best used in conjunction with other geological studies to determine the origin of known deposits; concept-oriented exploration programs can then be developed to find similar deposits. Geochemical processes are capable of causing different S '41S" ratios in the minerals and fluids participating in natural reactions. Because the magnitude of the resultant isotopic difference is inversely proportional to temperature, sulfur isotopic studies can be used to determine the source of the sulfur in high temperature deposits. The narrow spread of sulfur isotopic values from ores related to cupolas of felsic intrusions suggests that the sulfur in the ore-forming fluids was derived from a fairly uniform source (such as the intrusions) rather than by heated ground water from the adjacent country rocks. However, geologic and isotopic evidence suggest that the sulfur of many nickel sulfide ores may have been derived from the country rocks rather than the associated mafic igneous rocks. This sulfurization hypothesis implies that mafic intrusions in sulfur-rich country rocks should be prime exploration targets. Sulfur isotopic analyses of sulfides in the mafic rocks may indicate whether sulfurization has occurred. In equilibrium geochemical reactions S" is concentrated in the minerals with the greater bonding strengths. Thus the isotopic compositions of coprecipitated sulfides that have not undergone exsolution may be used as geothermometers and to distinguish multiple periods of mineralization, post-ore metamorphism, etc. The sulfur isotopic compositions of coexisting sulfides at Butte, Mont., indicate that the copper minerals did not originate by simple replacement of pyrite. Geologic and isotopic evidence suggest that the mineralogical and isotopic zoning at Butte formed almost isothermally during the geochemical evolution of the ore-forming fluids upward and outward from the Central zone. Unidirectional reactions cause enrichment of S" in the products. At low temperatures the isotopic effects of bacterial and inorganic reactions are difficult to distinguish. Anaerobic sulfate-reducing bacteria apparently were responsible for the sulfur of Gulf Coast salt domes and for diagenetic pyrite in sandstone-type uranium deposits. Sulfur (and carbon) isotopic data suggest that the roll ore bodies of sandstone-type uranium deposits originated by limited inorganic oxidation of diagenetic pyrite rather than by bacterial activity. Accordingly roll ore bodies should be most numerous and thickest against those portions of the sandstone aquifer that contain pre-ore pyrite.

Jan 1, 1975

By H. M. Wilten

THIS article presets a view of a problem encountered in petroleum refining in the deterioration of equipment used in condensation of vapors and cooling of liquids. Discussion is limited to the problems of shell- and tube-type exchangers and condensers. In this service shell- and .tube-type equipment is gradually displacing other types and, for this reason, its economic importance ill oil-refining practice is also increasing. Considering oil - refinery practice during the last two decades one can readily see many important improvements in the apparatus used. Briefly, the present equipment is safer, more efficient, and Ignore economical. Improvement in apparatus used for the condensation of distillates has, in my opinion, been less than that in other essential distilling apparatus. So it is hoped that this discussion will stimulate research among the producers as well as among the consumers of this equipment with a view to ameliorating this condition.

Jan 1, 1937

By John C. Sawyer

The mechanism of catastrophic oxidation of chromium and 446 stainless steel is examined. Data are presented to show that accelerated oxidation of these two materials, as caused by lead oxide, can occur in the absence of a liquid layer contrary to presently accepted theory. An alternate theory is proposed in which the rate of accelerated oxidation is a function of the rate at which lead oxide destroys the protective oxide formed on the base metal. An example of the application of the theory is given for the catastrophic oxidation of chromium in the presence of lead oxide. WHEN stainless iron-, nickel-, or cobalt-base alloys are heated in air to moderate temperatures in the presence of certain metallic oxides, oxidation will proceed at an accelerated rate. This phenomenon, often called "catastrophic oxidation", is most pronounced for the stainless steels. With these alloys the condition is so severe that large masses of oxide will form on the surface of the alloy in 1 hr or less at temperatures of 1200o to 1700oF. While a number of oxides are known to cause this effect, PbO, V2O5, and Moo3 are the most familiar, having been the subject of one or more investigations which have appeared in the literature.1-7 In presenting the results of these investigations, many of the authors have offered possible explanations to account for the more rapid rate of oxidation observed; however, the liquid layer theory as proposed by Rathenau and Meijering 2 has been the most commonly accepted mechanism. The liquid layer theory proposes that a low-melting oxide layer is formed on the surface of the alloy as the result of the interaction of the alloy oxide and the contaminating oxide. When the temperature of oxidation is above the melting point of the oxide on the surface, a liquid layer will form and oxidation will proceed at an accelerated rate. At temperatures below the melting point of the surface oxide, oxidation will proceed more slowly in the normal manner. It is argued that the rates of diffusion of oxygen and metal ions through the liquid layer are extremely rapid thereby accounting for the high rate of oxidation. Various experimental data have been presented to show that the temperature at which accelerated oxidation first becomes apparent coincides with the melting point of the eutectic oxide which would be present on the surface. Some exceptions have been observed, e.g., silver will oxidize in the presence of Moo3 at temperatures below the lowest melting eutectic; on the other hand, stainless steel will not be catastrophically oxidized at 1500oF in a molten bath of PbO and SiO2. In reviewing the various theories which have been used to explain catastrophic oxidation, Kubaschewski and Hopkins 8 favor the liquid layer theory, but note that, ".. .as experimental observations are not altogether in agreement with this theory (liquid layer theory), one should consider it a necessary but not a sufficient condition." In contemplating the liquid layer theory, it appears that sufficient evidence has not been presented to establish the theory beyond question. As a means of further clarification, a program of research was undertaken to determine in greater detail the mechanism of accelerated oxidation as caused by lead oxide. The first part of the program deals with a comparison of the oxidation of both AISI 446 stainless steel and chromium metal in the presence of lead oxide, vs the oxidation of these two materials in air alone. These comparisons are made at a number of different temperatures, most of which are below the melting point of the surface oxides. The second part of the program is concerned with a presentation of an alternate theory of accelerated oxidation exemplified by the system Cr-PbO-Air. PROCEDURE AND RESULTS Several experimental methods are commonly used to follow the progress of oxidation. One of these, the weight-gain method, was chosen for this work. This procedure requires that a specimen of the alloy be weighed, oxidized for a given period of time at an elevated temperature, and reweighed—the difference between the two weights being noted. The weight gain of the specimen represents the amount of oxygen acquired from the atmosphere to transform a portion of the specimen to oxide. In those cases where there is a tendency for the specimen or oxide to volatilize at the testing temperature, additional data must be collected so that a correction factor can be determined. This factor must be applied to the weight change in order to ascertain the actual amount of oxidation which has taken place. The specimens used for this work were 1 1/2 in.

Jan 1, 1963

By D. M. Buck

greatly restricted and every effort is being made to do away with it where possible, and to substitute a lead-base babbitt or a babbitt with 50 per cent,. tin. The amount of solder having the composition 50 lead, 50 tin, used by the Pennsylvania Lines East, during 1917, was approximately 100,000 lb., but there is reason to believe that a large portion of this can be replaced by a 60-lead, 40-tin solder with satisfactory results, and instructions have been issued to this effect. Inregard to the quantity of new tin used, it is not possible to give the amount, except approximately and from calculations based on the 1917 consumption of bearing metals by the Pennsylvania Lines East only, it is estimated that about 770,000 Ib. of new tin were required in a total of about 21,380,000 lb. of all kinds of bearing metals turned out by the foundry or purchased in the market. No change has been made in the specifications for bearing metals for some years, as the metals used have been satisfactory. A large proportion of the bearing metals are made up from old material re-melted and brought to standard composition by some addition of new metal, and every effort is being made to utilize old material to the best advantage and reduce the amount of new metal of all kinds purchased. For a number of years no tin has been used in the lining metal of either passenger or freight car journal-bearings, except such small amounts as come in from re-melting old linings. No change has been made in phosphor bronze used for rod bushings, as we should expect some trouble from bushings pounding out of shape if a phosphor bronze were used which contained less tin or more lead than the present specifications call for. In this, as well as in the case of all other bearing metals, we expect to use our utmost endeavors to economize and to substitute for tin wherever possible. The Tin-plate Industry D. M. Buck,* Pittsburg, Pa.—During the first 5 months of 1918, approximately 11,000,000 Ib. per month of pig tin were consumed in the United States. Solder, bearing metals, bronzes, etc, used about 5,500,000 lb.; collapsible tubes a little more than 250,000 lb.; tin-foil about 500,000 lb.; and the tin- and terne-plate industry somewhat less than 5,000,000 Ib. In an effort to reduce this consumption and thus conserve our tin supplies, several methods of procedure suggest themselves: 1. Salvage. The most careful and systematic collection and re-use of tin and tin-bearing materials is economically important, in that we thus

Jan 1, 1919

By F. R. Milliken

EXPERIMENTS, in what has come to be known as flash roasting began some ten years ago. The principle underlying the operation was not a new one, but the experimental work started at that time was the first that was carried through to a logical conclusion, followed by construction and operation of a pilot plant, and then full-scale production. For a short working definition, flash roasting may he considered the instantaneous and complete oxidation of finely ground sulphide particles, partially suspended in air or gas, the oxidation reaction evolving enough heat to make the reaction self-sustaining, or nearly so.

Jan 1, 1937

By George M. Bouton, Lawrence Ferguson

The experiments described in this publication were inspired by the Bell System's large interest in lead-alloy sheathed cables and by the wide range of fatigue and corroding conditions to which they are sometimes subjected in service. The first experiments consisted of operating specimens of lead + I per cent antimony telephone cable sheath alloy in a fatigue test while they were immersed in water taken from a manhole. Because of many published reports concerning corrosion-fatigue phenomena of various metals and alloys, a reduction in fatigue life was expected(1)2 Instead, however, the fatigue test ran on for many times the normal number of cycles an4 was finally stopped without failure. Because of this, the experiments were broadened to include the effect of many media on the fatigue properties of four lead alloys over a wide range of testing speeds and strains. One material, a viscous tacky polymerized isobutylene3 used in

Jan 1, 1945