Search Documents

By L. D. Wooddy, Robert Moscrip

The simultaneous solution of the volumerric balance and the unsteady-state equation has been used for several years to make performance calculations for combination drive reservoirs. This method makes possible the calculation of volumetric changes of fluids in the gas cap, oil zone, and aquifer which occur as a result of withdrawals and reservoir pressure changes. It does not provide a means for the determination of reservoir fluid distribution changes corresponding to these vollrmetric changes. A knowledge of the fluid saturation distribution in the reservoir at various stages of depletion is important for the determination of the efficiency of gas and water as oil-displacement media and, therefore, for the reliable predicrion of ultimate oil recovery. To provide this knowledge, the displacement equations are solved simultaneously with the volumetric balance and unsteady-state equations. The described calculation procedure has been used satisfactorily to analyze the past performance and to predict the future behavior of combination drive reservoirs under both primary and pressure-maintenance operations. INTRODUCTION The three basic mechanisms by which oil is displaced from a reservoir are: (1) dissolved gas drive—the displacement of oil by the expansion of liberated solution gas, (2) water drive—the displacement of oil by water which enters the oil zone from the aquifer, and (3) gas cap drive—the displacement of oil by gas which ex- pands into the oil zone from the gas cap. The action of gravitational forces may be effective in increasing the efficiency of the basic drive mechanisms. Gravitational forces favor the segregation both of gas and oil and of oil and water, thus tending to shorten the transition zone between oil and displacing fluids. Most reservoirs produce under the influence of a combination of these drives and are designated "combination drive reservoirs". Fig. 1 is a cross section of a typical combination drive reservoir. A calculation procedure for analyzing the performance of combination drive reservoirs has been developed by combining the displacement equations' with the volumetric balance equation' and the unsteady-state equations. The pressure-production performance and the positions of the gas-oil and oil-water contacts are calculated for several stages of reservoir depletion by solving these equations simultaneously, thus affording a basis for: 1. Determining instantaneous and ultimate oil, gas, and water production under various operating conditions. 2. 'Establishing a maximum efficient rate of production, 3. Determining the advantages of pressure maintenance and unitization, and 4. Designing surface installations necessary for primarv and pressure-maintenance operations. DEFINITIONS The calculation procedure for combination drive res-

Jan 1, 1957

By J. R. Martson

The arrangement of the larger furnace at the United Verde smelter, together with the boiler layout and connecting flues, is shown in Fig. 1. The important dimensions are given in the figure, and cross-sectional areas of combustion space, flues, etc., are recorded. The location and extent of the baffling in the boilers also are shown because of their importance in the interpretation of the data. Two boilers serve each reverberatory furnace. They are of the class M-26 Stirling type (rated at 713 boiler hp. each). Steam is generated at 178-lb. gage pressure at a total temperature of 528" F., from feed water at a temperature of 113" F. The feed water is condensate from turbogenerators plus make-up softened by the lime-soda process. The make-up is rather large in amount as it must match the amount of steam consumed in reciprocating blowing engines and the like, which are not served by surface condensers. As a result the boiler feed water has a hardness of 1.5 to 3.0 grains per gallon, but this results in the formation, during six months to one year of boiler operation, of scale only of "eggshell " thickness or less. The boilers are set at the same elevation as the tapping floor of the furnace, which results in the introduction of the waste-heat gases at the top of the front bank of tubes and necessitates the inversion of the usual baffling arrangements. The boilers are equipped with valve-in-the-head soot blowers, which keep most of the dust blown off the surface of the tubes, but it is necessary to supplement the soot blowers by high-pressure air lances, inserted by an attendant through side doors in the boiler setting. Deposits of coal ash and of dust from the furnace charge accumulate in the flues between the reverberatory furnaces and the boilers and this necessitates cleaning of these connecting flues by hand during the greater part of one of the three 8-hr. shifts during each 24 hr. This cleaning operation requires the opening of clean-out doors, which, of course, has some effect on the yield of steam. Revebberatory Furnace Practice The United Verde furnaces are fired with pulverized coal of sub-bituminous type of which the screen and chemical analyses are given in Table 1.

Jan 1, 1934

By J. W. Leonard, B. A. Donahue

A method is described for incorporating coal petrography into mining and preparation plant quality control based on conventional analyses. Complete analyses are made of each of the uniform and relatively distinct petrographic bands in a coal face. With this information it is possible to develop petrographic standardization curves. These curves permit diverse coal characteristics to be rapidly monitored by application of a few standard coal tests. Single seam quality control is discussed in this paper. Inquiries continue to be made about coal petrography, and specifically, about whether coal petrography should be applied more extensively in the coal industry. Coal petrography is the study of the distinct physical, optical, and chemical increments which make up the organic rock mixture which we know as coal. Petrography can be applied by any coal company or at any coal mine where conventional coal analytical facilities are available and where additional resources can be allocated for an increased number of determinations. This first paper of a two part series includes (1) a proposed conventional approach to single seam petrography based on the development of petrographic standardization graphs and (2) some informative and supplemental interrelationships involving coal characteristics developed as a result of this research. In the second part of this series, to be published at a later date, those petrographic characteristics of bands taken from many different coal seams located over wide geographic areas which can be closely related to each other will be considered. These findings will be examined looking toward the development of a comprehensive, conventional approach to coal petrography which can be used as a common basis for multi-rank petrographic standardization graphs. Implicit to the understanding of coal petrography is the well established fact1,2 that the individual analyses of distinct petrographic bands often differ widely from the average analysis which is used to characterize a whole coal seam. In fact, a distinct and minor banded increment of coal in a high volatile seam may actually be a medium or low volatile coal with an analysis similar to the average analyses of seams located in distant coal fields. During the mining of coal, much degradation is caused which tends to randomly scatter coal bands. The degraded, scattered, and physically separated constituents of distinct petrographic bands are processed side by side in the coal preparation plant as distinct petrographic fractions with particles grouped according to a narrow size range (which derives in part from common hardness), specific gravity, and-or surface chemistry. Tile data obtained from numerous analyses made on each of the bands of any given coal seam, although diverse, can be readily interrelated. Indeed, these interrelationships can be developed into a series of nomographs or petrographic standardization graphs to serve as a basis for developing a conventional petrographic* program. Thus, by analyzing one property (for example, ash) of a selected petrographic fraction collected or separated from the flow of coal in a preparation plant, it should be possible to estimate the other physical, chemical, and thermal properties of this fraction by referring to the petrographic standardization graphs. It follows that any or all petrographic fractions in the total coal flow originating from a single coal seam can be rapidly monitored for many properties on the basis of a single analysis run on each fraction. In recent years coal petrographic research has concentrated heavily on that phase of this work which involves microscopic reflectance measurements made at many minute and selected points on a coal briquette surface.3,4 Thus, the percentage of the total number of reflectance measurements that fall into each of a consecutive series of arbitrarily chosen reflectance classes are used to characterize coal. This procedure is analagous to using the face of a coal briquette to represent the reflectance characteristics present at the face of a coal seam. Moreover, by analyzing petrographic fractions of known and uniform optical properties it is possible to closely relate reflectance to other coal characteristics. For example, reflectance has long been known to be related to such

Jan 1, 1968

By Charles Hardy

ACTIVATED alumina is an aluminous material which may be 1 classified chemically as a partially dehydrated aluminum trihydrate having a high porosity and a perma¬nent physical structure. In general, it may be employed effectively and economically for the complete removal of water vapor from gases and vapors; for the selective adsorption of certain as especially those of the higher boiling points, and as a catalyst or catalyst carrier. Other forms of alumna are available and may be employed similarly but not so effectively nor can reactivation be accomplished with uniformity over many cycles without deterioration. The adsorption-reactivation cycle of activated alumina can be repeated many times without any apparent depreciation ill

Jan 1, 1934

By Henry Seltz, Cyril Wells, Hugh J. MacDonald

Several investigators have measured the heat capacity of cementite, using different methods of attack, but the agreement between the values obtained cannot be considered good. Naeserl has made measurements of "average heat capacities" of iron carbide between 1026" and 85" K., using a water calorimeter. His computed true specific heat at 78.1" K. is 11.22 cal. per gram-formula mass, which, if correct, is much too high for any reasonably accurate extrapolation to 0" K. The cementitc used by Naeser was obtained from a steel containing 0.9 per cent carbon, by electrolytically dissolving out the iron in a neutral bath of ferrous chloride. The cementite remained as a coarse, crystalline, gray powder. Andes2 has measured the specific heat of iron carbide, from 102" to 323" K., as it exists in steel. The specific heats of several slugs of steel of known iron carbide content were determined, and the specific heat of the iron carbide (Fe3C) calculated by plotting specific heat versus percentage of carbon, and extrapolating to pure Fe3C (6.7 per cent C). The heat-capacity values for temperatures below 100" K. were obtained by comparing the temperature-specific heat curve for Fe3C to that of Fe. Since the two were very similar in the range examined experimentally and approach more closely at low temperatures, it was assumed that near the absolute zero the form of the curve for Fe3C would be similar to that of Fe. Andes calculates for the entropy of Fe3 C,S298 = 23.55 e.u. The heat of formation of Fe3C has been studied by several workers. Kelley3 has reviewed these measurements and calculations, and selects those of Roth* and Naeser6 as worthy of most consideration. Roth has given AH = 5400 cal. + 30 per cent as a result of his own and other work. Naeser has determined the heat of formation from Fe and different forms of carbon, and for graphite (0) he finds AH = 5600 cal. Kelley accepts the rounded figure AH = 5500 as the heat of formation at 298.1" K., but this value is quite uncertain.

Jan 1, 1940

By Henry Seltz, Hugh J. MacDonald, Cyril Wells

Several investigators have measured the heat capacity of cementite, using different methods of attack, but the agreement between the values obtained cannot be considered good. Naeserl has made measurements of "average heat capacities" of iron carbide between 1026" and 85" K., using a water calorimeter. His computed true specific heat at 78.1" K. is 11.22 cal. per gram-formula mass, which, if correct, is much too high for any reasonably accurate extrapolation to 0" K. The cementitc used by Naeser was obtained from a steel containing 0.9 per cent carbon, by electrolytically dissolving out the iron in a neutral bath of ferrous chloride. The cementite remained as a coarse, crystalline, gray powder. Andes2 has measured the specific heat of iron carbide, from 102" to 323" K., as it exists in steel. The specific heats of several slugs of steel of known iron carbide content were determined, and the specific heat of the iron carbide (Fe3C) calculated by plotting specific heat versus percentage of carbon, and extrapolating to pure Fe3C (6.7 per cent C). The heat-capacity values for temperatures below 100" K. were obtained by comparing the temperature-specific heat curve for Fe3C to that of Fe. Since the two were very similar in the range examined experimentally and approach more closely at low temperatures, it was assumed that near the absolute zero the form of the curve for Fe3C would be similar to that of Fe. Andes calculates for the entropy of Fe3 C,S298 = 23.55 e.u. The heat of formation of Fe3C has been studied by several workers. Kelley3 has reviewed these measurements and calculations, and selects those of Roth* and Naeser6 as worthy of most consideration. Roth has given AH = 5400 cal. + 30 per cent as a result of his own and other work. Naeser has determined the heat of formation from Fe and different forms of carbon, and for graphite (0) he finds AH = 5600 cal. Kelley accepts the rounded figure AH = 5500 as the heat of formation at 298.1" K., but this value is quite uncertain.

Jan 1, 1940

By D. B. Myers

The consistent upward trend in crude oil production prevailing in California throughout the greater part of 1929, was effectively checked in November by a curtailment program instituted by mutual agreement between operators in four of the major fields. This program artificially reduced daily production to approximately the same daily figure as prevailed in December, 1928. The large amount of deep drilling during the later part of 1928 and during 1929 has established a potential, however, which is far in excess of refinery needs in the state. Low prices for crude oil which prevailed in California during 1928 continued during 1929. General curtailment continued in the older fields in San Joaquin Valley. The number of wildcat and exploratory wells drilled throughout California was materially increased, but no major field was discovered unless the recent bringing in of the Ohio Oil Co.'s Recreation Gun Club No. 1 well, near Venice in Los Angeles Basin, during the closing days of 1929 results in such a field. Significant developments during 1929 were: (1) The discovery of three deeper zones in the Santa Fe Springs field known as the O'Connell, Clarke, and Hathaway; (2) Kettleman Hills development and unanimous agreement to restrict production; (3) developments along the Santa Barbara Coast and the drilling of tideland permits; (4) extensions of some of the older producing areas in the San Joaquin Valley; (5) the Lawndale and Santa Barbara Mesa structures, the former discovered in Los Angeles Basin in 1928, the latter in Santa Barbara County in 1929, proved to be failures; (6) intensive exploration throughout the state and the drilling of a large number of deep wildcat wells; (7) discovery of oil by the Ohio Oil Co. in the Los Angeles Basin at Venice; (8) Long Beach and Ventura Avenue fields maintained steady production throughout the year. As a natural sequence to the discovery of high-gravity oil fields in Kettleman Hills and at Elwood in 1928, a tremendous amount of exploratory work was done in 1929 in areas underlain by rocks of lower Miocene age, particularly along the Santa Barbara Coast area, the San Joaquin Valley, and the Salinas Valley, where the Vaqueros and Temblor sands were considered to hold possibilities for production.

Jan 1, 1930

By AIME AIME

THE Iron and Steel and Institute of Metals Divisions will meet jointly at the Statler Hotel, Detroit, Oct. 4 and 5, during the Metal Congress, Oct. 2-6. The Wire Association, the American Welding Society and the American Society for Steel Treating, together with the two Divisions of the Institute, constitute the Congress this year, and each body offers an interesting technical program. The National Metal Exposition will, as usual, be held concurrently. Visiting metallurgists will find themselves engaged in a bit of research not listed in the program-a time study of how best to exploit in a few days both the Congress and all that the place of meeting has to offer. For Detroit, the beautiful "City of the Straits," is third in rank industrially in the United States, and its great manufacturing plants offer much of metallurgical interest. This is especially true of the automobile plants which will be open to members of the various societies during the week of the Congress.

Jan 1, 1933

By Davis Baker

The direct-metal cars or ladles of the Maryland Steel Company have a capacity of 18 tons when filled within 12 inches of the top. On account of this large capacity, the formation of skulls in these ladles is by no means as rapid as in smaller ladles; but a skull once formed is a very unwieldy piece of metal to handle, and especially to remove from the ladle. We have found it cheaper to clean ladles often rather than make very heavy skulls. We aim to keep the ring of chilled metal that forms on the surface of the iron chipped off, so that the skull shall form principally at the bottom until it becomes so thick as to render the ladle unfit for service. Sometimes it happens that a ladle may be held for several hours filled with molten metal. This invariably leaves a large amount of chilled metal in the ladle. Frequently the skull will weigh several tons, and will be of the full size of the ladle inside, with a top crust, having perhaps a hole 12 inches square, through which the molten metal was poured. In order to remove skulls that cannot be easily chipped out with a bar, we use what may be called a skull-extractor, consisting of a hydraulic cylinder mounted in the center of a heavy cast-iron plate, standing vertically on a suitable foundation. Figs. 1 and 2 show the construction and operation of this apparatus, Fig. 1 being a view of the extractor with pistons extended to full stroke, and Fig. 2 a view with ladle in position and pistons about to commence the stroke. in both figures, A is the hydraulic cylinder, B the vertical cast-iron plate, and C the foundation. The water-pressure, admitted through the pipe, P, is 750 pounds per square inch, and the inside diameter of A is 14 inches. There are two pistons: D, fitting the bore of the cylinder, and E, 84 inches in diameter, moving inside of D. Both pistons move together when

Jan 1, 1893

By J. J. Lillie

Sublevel stoping was first developed in the Michigan iron mines many years ago. Since that time this method, and modifications with long hole drilling, have been used in a number of non-ferrous mines and have been described in various papers and articles. With a few exceptions, the operations where sublevel methods have been applied are producers of large daily tonnages from ore bodies of considerable size. In selecting mining methods for small properties or relatively small detached ore bodies, sublevel methods often have been overlooked. The method has been used successfully in relatively small operations at Copper Canyon, Nevada, and, more recently, in mining small ore bodies at Darwin, Calif. As a result of this experience, we believe that a review of the general procedure, the advantages noted, and the results obtained will be of interest to many operators of relatively small mines. General Description Briefly, sublevel stoping consists of, first, driving sublevel drifts at predetermined vertical intervals through the length of the stope block; second, breaking an initial mining slot across the stope; third, driving crosscut benches from each sublevel by slabbing into the slot; and, fourth, breaking the ground between benches. Applicability Since this is an open stope method, it requires wall rock that will stand over reasonable stope lengths without caving or excessive slabbing. Ore must be moderately firm but need not be hard. The method is best adapted to steep dipping, tabular or lenticular ore bodies but may be applied to ore bodies of almost any shape if their vertical extent is appreciable. It can be used with dips that are too flat for successful shrinkage stopes and can be modified for use with slushers on dips below about 40". Initial mining at the Copper Canyon operation consisted of sublevel stopes for the wider ore sections and shrinkage stopes for the narrow sections where ore widths averaged about 15 ft. After some experience and a study of comparative results on completed stope blocks, sublevels were substituted for shrinkage stopes even in the narrow ore widths. Practical stope lengths depend upon the character of the walls and the continuity of values within the ore body. Where blocks of low grade or waste are included in the stoping limits, these areas can readily be left as pillars for intermediate wall support and longer stope lengths may be planned. Raises can be spotted in narrow or low grade areas and stope lengths adjusted accordingly. Stoping Details To illustrate stoping details, assume that we have an ore shoot 15 to 30 ft wide and about 200 ft long, with walls that would stand over a stope length of 80 to 90 ft (Fig1). PRELIMINARY DEVELOPMENT Preliminary development for sublevel stoping would be simple. A service raise is driven at about the center of the block and stope limits planned to leave a pillar around this raise. Sublevel drifts driven each way from this central raise will outline the

Jan 1, 1950

By M.A. Hunter

This paper gives the results of an investigation of the specific resistance and temperature coefficient of the electrical resistance of nickel and its important alloy, monel metal. For most of the pure metals, the temperature coefficient of resistance is approximately 0.004 per degree centigrade at 20" C. Nickel and iron, however, are exceptions. This property is important as it gives us good material for the construction of thermometers and other instruments involving electrical control. A summary of information on this subject has been publishcd by the Bureau of Standards.l The present experiments antedate this publication by several years and as the information obtained is not contained in it, the results of the experiments arc published as additional information. Electrical Properties of Pure Nickel It is generally conceded that the lowest values for electrical resistance are obtained in the purest metal. In the case of nickel, the best material obtainable is electrolytic nickel, which contains approximately 99.80 per cent. nickel, 0.15 per cent. iron, and 0.05 per cent. copper. Any cobalt that may be present is included in the nickel figure. If the elcctrolStic sheet has been deposited without intermission, it is possible to cut a section from the sheet and roll it into wire without melting. By this means a nickel wire may be obtained that is uncontaminated by any of the impurities always taken up by nickel during melting. Two samples of nickel wire obtained from different electrolytic nickels had the follolving electrical resistance and temperature coefficient of electrical resistance: Specific Temp. CofEE. Sample MateRial ReSISTance peR Deg. C. NO. 1 Electrolytic nickel.................... 7.55 0.00550 NO. 2 Electrolytic nickcl ................... 7.60 0.00553 * Rensselacr Polytechnic Institute. Director of Research, Driver-Harris Co. Russell Sage Laboratory, Rensselaer Polyt,ecllnic Institute. 1 U. S. Bureau of Standards, Circular 100 (March, 1921).

Jan 1, 1923

By M. A. Hunter

This paper gives the results of an investigation of the specific resistance and temperature coefficient of the electrical resistance of nickel and its important alloy, monel metal. For most of the pure metals, the temperature coefficient of resistance is approximately 0.004 per degree centigrade at 20" C. Nickel and iron, however, are exceptions. This property is important as it gives us good material for the construction of thermometers and other instruments involving electrical control. A summary of information on this subject has been publishcd by the Bureau of Standards.l The present experiments antedate this publication by several years and as the information obtained is not contained in it, the results of the experiments arc published as additional information. Electrical Properties of Pure Nickel It is generally conceded that the lowest values for electrical resistance are obtained in the purest metal. In the case of nickel, the best material obtainable is electrolytic nickel, which contains approximately 99.80 per cent. nickel, 0.15 per cent. iron, and 0.05 per cent. copper. Any cobalt that may be present is included in the nickel figure. If the elcctrolStic sheet has been deposited without intermission, it is possible to cut a section from the sheet and roll it into wire without melting. By this means a nickel wire may be obtained that is uncontaminated by any of the impurities always taken up by nickel during melting. Two samples of nickel wire obtained from different electrolytic nickels had the follolving electrical resistance and temperature coefficient of electrical resistance: Specific Temp. CofEE. Sample MateRial ReSISTance peR Deg. C. NO. 1 Electrolytic nickel.................... 7.55 0.00550 NO. 2 Electrolytic nickcl ................... 7.60 0.00553 * Rensselacr Polytechnic Institute. Director of Research, Driver-Harris Co. Russell Sage Laboratory, Rensselaer Polyt,ecllnic Institute. 1 U. S. Bureau of Standards, Circular 100 (March, 1921).

Jan 1, 1923

By Shiou-Chuan Sun

THE presence of an excessive amount of tough froth in the flotation of minerals, particularly coals, may create trouble in dewatering, filtering, and handling. Froth is also a nuisance in many chemical industries.' This paper presents a study on the destruction of extremely tough froths with intense high-frequency sound. The data indicate that sound waves can be employed for continuous atandsoundwavescan instantaneous defrothing. A powerful high-frequency siren was used in obtaining the data. Also tested was an ultrasonorator of the crystal type with a frequency range of 400, 700, 1000, and 1500 kc per sec and a maximum power output from its amplifier of 198 w. The results, not presented, indicate that as now designed this machine is not suitable for defrothing. Although the sound generators of the magnetostriction type2,3 and of the electromagnetic type'.' were not available, it is beelectromagneticlieved they are capable of producing the required sound intensity for defrothing. The use of ultrasonics for defrothing was suggested by Ross and McBain1 in 1944. Ramsey8 reported in 1948 that E. H. Rose mentioned a supersonic device that broke down flotation froth but with low capacity. The writer has not been able to find any published literature containing practical experiments. Theoretical Considerations The mechanism of defrothing by sound is attributed to the periodically collapsing force of the propagated sound waves and the induced resonant vibration of the bubbles. The collapse of froth is further facilitated by the sonic wind and the heat of the siren. Sound waves can exert a radiation pressure'," against any obstacle upon which they impinge. When a froth surface is subjected to the periodic puncturing of sound waves, the bubbles are broken. According to Rayleigh9 and Bergmann,12 the radiation pressure of sound, P, in dynes per sq cm is given as: P = 1/2 (r+1)i/v where r is the ratio of the specific heats of the medium through which sound is traveling and is equal to 1 on the basis of Boyle's law; i is the sound intensity in ergs per sec per sq cm, and v is the sound velocity in cm per sec. In this case, the accuracy of the formula is only approximate, because a perfect reflection can hardly result from a column of froth. In addition to the radiation pressure, the propagated sound waves cause the bubbles of the froth to have a resonant vibration.'" he vibratory motion of the bubbles causes collision and coalescence, thereby weakening if not breaking the bubble walls. Sonic wind and heat were also generated." The sonic wind can exert pressure on the froth surface, and the heat can evaporate the moisture content of the bubble walls as well as expand the enclosed air. Apparatus The defrothing apparatus, shown in Figs. 1 and 2, consists of a powerful high-frequency siren, a glass or stainless steel beaker of 2-liter capacity with 12.4 cm diam and 17.1 cm height, and a metal reflector. The beaker was placed 2 in. above the top point of the siren. The metal reflector was adjusted to reflect and focus the generated sound waves into the central part of the beaker. Fig. 2 shows the crystal probe microphone used to measure the acoustic intensity and the mandler bacteriological filter employed to introduce compressed air into the beaker for frothing. The apparatus was enclosed in a soundproof cabinet equipped with a glass window. The siren, shown in Fig. 3, consists of a rotor that interrupts the flow of air through the orifices in a stator. The rotor, a 6-in. diam disk with 100 equally spaced slots, is driven by a 2/3 hp, Dumore W2 motor at 133 rps. The frequency of the siren can be varied from 3 to 34 kc. The maximum chamber pressure is about 2 atm, yielding acoustic outputs of approximately 2 kw at an efficiency of about 20 pct. The siren itself is relatively small and can be operated in any orientation. A detailed description of the siren has been given by Allen and Rudnick.11 Collapse of Froth To study the sequence of the collapse of froth, the glass beaker was partially filled with 920 cc water, 100 g of —150 mesh bituminous coal, 0.3 cc petroleum light oil, 0.2 cc pine oil and 1.54 cc Pyrene foam compound. This mineral pulp was agitated for 5 min and then aerated through a mandler filter until the empty space of the beaker, approximately 9 cm high, was filled completely with min-

Jan 1, 1952

By R. H. Winn

In this paper a heterogeneous carbonate reservoir is considered as a succession of layers of formations of radically different porosities, permeabilities, water saturations, and rock matrix types; i.e., the heterogeneity is vertical rather than radial to the wellbore. Presumably each layer is more or less homogeneous. To determine the "net oil in place" in this reservoir it is desirable to know the porosity and water saturation of each layer. In addition, the section must be subdivided into that which will produce oil, that which will produce water, and that which will produce little or nothing. In numerous wells drilled in these reservoirs radioactivity surveys, guard electrode surveys, and caliper surveys have been made. These logs have been compared with core analysis data, when available, and the analysis of the surveys compared with production data. This study, still in progress, is intended to provide improved analytical techniques if such are possible. This paper is a progress report on the work. DETERMINATION OF POROSITY The neutron-gamma log has long been recognized as a measure of hydrogen concentration.1,2,3 In reservoirs that are free of clay, shale, or other hydrogen containing matrices, it has been accepted as a measure of porosity.4,5 Empirical methods to relate relative neu-tron-gamma intensity to porosity are often employed." To provide a more precise determination of porosity from the neutron-gamma log each instrument is calibrated immediately prior to each survey by a method which refers all tools to a hydrogenous cylinder. To insure stability a calibration check is made after each survey. These calibration records are printed as an integral part of the log that is recorded in standard counts per second. A detailed description of the calibration procedure is available in the literature.' The procedure employed insures that each Survey is numerically reproducible within the limits of statistical variation. To relate the standard neutron counts per second to porosity and hole size, records were made in test wells constructed of blocks of limestone. The porosities of the blocks were accurately measured and the blocks completely saturated with fresh water. Fig. 1 presents some of the results obtained in these test wells.' The lines shown in Fig. 1 were obtained by deriving an empirical equation relating the 11 points shown so that the relationship may be projected to larger and smaller hole sizes. A detailed description of the tool is available in the literature.' Field tests indicate that the tool is adjacent to the wall of the hole most of the time when the surveys are made in uncased holes drilled with saline muds. In this circumstance porosity may be calculated from Fig. 1 if the hole size is known. When fresh muds that form thick mud cakes are employed, the centralizing effect of the mud cake must be considered and the porosity determination is less reliable. In cased holes the combined effect of variations in hole diameter and the unknown eccentricity of the casing in the hole may make porosity determinations extremely unreliable. In any event, an accurate knowledge of hole size is essen-

Jan 1, 1958

By H. C. Johnson, J. K. Elliott

One of the primary requirements for successful operation of an enriched gas-drive project is to control the composition of injection gas. This can become a serious and difficult problem, particularly in cases where the enrichment material is being furnished from a number of field -produced gas streams. It is possible to effect control of the injection gas composition through frequent or continuous sampling; however, this can be extremely costly and, in many cases, impractical due to laboratory requirements of time. Another alternative would be to provide a calculation technique which would be flexible and sufficiently accurate to predict composition of the liquid and gas streams of interest at any point in the system. The purpose of this paper is to discuss a technique that was used successfully on an operating enriched gas-drive project for developing information which could be used for controlling composition of the injected gas. FIELD OPERATIONS The particular field (hereafter called Example field) in the example operation being discussed is composed of four oil reservoirs (A. B, C and E) and one gas condensate reservoir (D). Casinghead gas from the oil reservoirs and gas from the gas condensate reservoir are gathered through a field gathering system as shown in Fig. I for injection into Reservoir C. The gas mixture which is recovered from the five reservoirs for injection purposes is composed of gases liberated in 19 individual separators, each operating at a separate temperature and pressure. PROPOSED CALCULATION TECHNIQUE It is well known that vapor-liquid equilibrium calculations in general use throughout the petroleum industry can be used to predict reliably the phase behavior of hydrocarbon mixtures, particularly at pressures less than 1,000 psig. It is then a simple matter to account for the material on a ComPonent basis by m''ing flash and material balance calculations at each separation point in a hydrocarbon system. Accordingly, it was proposed to use vapor-liquid equilibrium and material balance cal- culations with a medium-sized electronic digital computer as a basis for developing a control procedure for use in controlling injection gas composition in the enriched gas-drive project. Although the approach is a simple one, the numerous vapor-liquid equilibrium calculations involved make the problem laborious; in this particular case, it would have been impractical to make sutficiently complete analysis without the aid of digital computing equipment. SAMPLING AND VERIFICATION OF CALCULATION PROCEDURE To obtain representative gas and liquid stream samples and to provide a quantitative measure of overall system Performance for comDarative purpLses, a thorough test of the field and plant system was conducted in the summer of 1957. Oil production at each battery was sta-

By Jack M. Swales

Kermac Potash Co., the newest American entry in a rapidly expanding industry, has come on the scene with notable variations in conventional shaft-sinking and mining techniques. Located in the famed potash producing district east of Carlsbad, N. Mex., Kermac started up its mine in November, 1965, to supply ore to the company's 500,000-tpy potash crystallization refinery. In so doing, the company (1) drilled the first large diameter mine shaft in the potash industry and (2) has employed new continuous miners especially adapted for use in thin potash beds. REACHING THE ORE ZONE In its initial mine planning, Kermac, a partnership owned jointly by Kerr-McGee Corp. and the National Farmers Union Development Corp., considered it imperative that the shafts be sunk and equipped as soon as possible and that the mine be developed sufficiently to insure a constant ore feed to the mill when the unit was placed on stream. After examining the alternative sinking techniques available to it, the company decided to accept a proposal by Big Hole Drillers, Inc., to drill the shaft from the surface through various formations of sandstones, siltstone, shales, anhydrite, limestones, dolomite and salts to the potash ore zone.

Jan 12, 1966

By G. S. Scott, H. G. Turner, W. L. Kleene

It is well known that different forms of carbon show differences in chemical behavior under apparently identical conditions. It is fairly well known that these differences persist, although to a lesser degree, in a single group of carbons, such as the anthracites of Pennsylvania. It is the purpose of this paper to show the extent of these variations for Pennsylvania anthracites from actual quantitative measurements of the amount of carbon dioxide reduced under the standardized test conditions employed. As the amount of carbon dioxide reduced to the monoxide (under comparative conditions termed, for convenience, the "reactivity") is important in combustion, gas production and metallurgy, it is hoped that this paper will be a useful contribution to the store of knowledge on these subjects. In carrying out the investigation, considerable time and thought were spent in obtaining what seemed to be the best possible design of apparatus. The next step consisted in making a number of trial runs on the same sample, varying temperature, particle diameter, etc. and then outlining a standardized procedure to be followed in testing all samples. Fifty anthracites were tested. As a matter of interest, some 10 miscellaneous samples were also tested. The data show initial reaction temperatures (abbreviated I.R.T.), reaction velocity constants at 900" and 950" C., some effects of added substances, and a few additional tests designed to throw some light on the causes of differences in reactivity. The sample of charcoal, as was anticipated, proved to be easily the most reactive of any sample tested. The anthracites as a group came second. The five samples of gas and by-product cokes, obtained from five different coke manufacturers, came third, and a single sample of Rhode Island anthracite ranked fourth, with respect to reactivity as above defined. Although the five coke samples do not necessarily represent the average market coke, and five samples constitute a rather small number of samples to serve as a basis for comparisons, the fact that none

Jan 1, 1934

By C. McDermid

At the request of Mr. C. McDermid, Secretary of the Institution of Mining and Metallurgy, Salisbury House, London, E. C., England, the following reports of standardization committees are here republished. Mr. McDermid invites members of-the American Institute of Mining Engineers to write him and express their opinion of the various proposals made by the committees. COPY OF THE REPORT OF THE WEIGHTS AND MEASURES STANDARDIZATION COMMITTEE OF THE INSTITUTION OF MINING AND METALLURGY, as adopted by the Central Standardization Committee; Dec. 20, 1906, and submitted to the Council, Jan. 16, 1907.

Mar 1, 1907

By F. W. McQuiston, L. J. Bechaud

3.2-1. Introduction. Much has appeared in the technical literature on theory of sampling (18, 37), weight of sample required in relation to particle size (28), probability of error in sampling (3), and statistical analysis of sample data (20). Each industry, whether it be copper, iron ore, or coal, has its own standards and methods. All of the rather extensive theoretical treatments appearing in published literature on sampling apply to material already on hand such as coal, iron ore, or copper concentrates in rail cars, or in moving streams such as on conveyor belts. The attempt usually is to apply statistical techniques in order to improve reliability and precision in sampling, and to reduce differences between the analyses of seller and buyer. In contrast to this type of sampling, very little has appeared in the literature on sampling a virgin deposit from the metallurgical point of view. Perhaps it would he more descriptive to designate this point of view as "Gm-metallurgical," since geology is inextricably interwoven with metallurgy in gaining an understanding of the complexities of a deposit, eventually leading to a definition of mineable reserves, with the development of a flowsheet and engineering criteria for the planning of a successful and profitable operation. The degree of cooperation between these two departments often determines whether the processing plant is a success at the inception of operations, or whether expensive changes and modifications must he made, with the plant finally reaching rated capacity at some later date. The first concern of the metallurgical department should be to establish proper accreditation of the samples which will be used in any ore-testing campaign. It should he made mandatory, as part of operating management policy, for the responsible metallurgist to he aware of the significance of the samples and to become intimately knowledgeable in all aspects of metallurgical behavior and response to treatment of all varieties of ore in the deposit under consideration.

Jan 1, 1968

By J. J. Knoerzer

A full-scale operational test was conducted on the Coaltek preheating and pipeline charging system at the Semet-Solvay Div. of Allied Chemical at Ironton, Ohio, for the purpose of determining whether a high-quality blast furnace coke could be made from blends containing at least 75% Illinois No. 6 Coal and at the same time reduce air pollution during the charging of the ovens. The coke produced had similar physical characteristics as compared to our conventional wet-charged coke, with the exception of smaller size for the preheat coke. Air pollution during charging was con- trolled and there were no serious operating problems. The coking time was reduced 25% from our normal 17 hr for wet charging to 12.8 hr for preheated charges. The blast furnace performance with preheat coke was satisfactory.

Jan 1, 1976