Search Documents

By E. O. Fromm, R. I. Jaffee, R. M. Evans

IN connection with a research on gallium alloys, a method for the thermal analysis of very low melting alloys was developed, which appeared to be worthy of more than passing interest. As used, the method was suitable for work in the temperature range, — 72° to 250°C. However, with suitable adjustment, the method could be adapted for use over broader temperature ranges. The Rosenhain temperature gradient furnace,' adapted for low-temperature use, was the basis for the method. The gradient was set up in a stainless steel tube. The specimens were lowered through it at a constant rate while time-temperature or inverse rate data were taken. It was essential to maintain careful control of the top and bottom temperatures of the gradient. Also essential was good heat transfer from the walls to the specimen. This was accomplished by a liquid heat-transfer medium.

Jan 1, 1953

By J. T. Ryan

SAFETY practice or the elimination of accidents in our coal mines is specifically a problem of management. It cannot be delegated to any governmental agency except that the various coal-producing states do and should have some minimum safety standard laws. However, the legislative method of attempting to control mine accidents is ineffective because of the delay between the necessity and the action. It will always be impossible to keep our various state mining laws up to date; and when the law says you must do a certain thin there is a tendency to do this and no more. Unless the scheme for setting up state regulations is so flexible that when a new hazard develops it can be immediately and adequately covered and the whole responsibility for accident elimination placed undivided on the

Jan 1, 1937

By David J. Mack, A. H. Kasberg

The transformation characteristics are found to resemble a similar binary alloy. The differences are due to the alpha iron particles. While strength properties of the isothermally transformed alloys are high, ductility is low, resulting in high notch sensitivity. The elastic modulus can be varied widely and correlates with strength. Abnormal grain growth sometimes occurs. A CONSIDERABLE amount of work has been done on the isothermal transformation of high purity aluminum bronzes using the methods pioneered by Davenport and Bain.' The first isothermal study of these alloys was made by Smith and Lind-lief,' but more recently Mack", " and Klier and Grymko5 have continued the work. In commercial aluminum bronzes, one or more elements are always added to refine the ß grain size and to improve the mechanical properties. The effect of these elements on the isothermal transformation has not been reported in the literature. No systematic study of the properties of isother-mally transformed aluminum bronzes has apparently been reported, although adequate information is available on their properties after more conventional heat treatments. The fact that a eutectoid alloy will reject face-centered cubic a during isothermal transformation at appropriate temperatures2'" warrants investigation of the properties of such structures. Another cogent reason for determination of properties is the fact that the modulus of elasticity of the eutectoid alloy varies widely with the nature of the heat treatment." Preliminary experiments7 indicated that a high purity eutectoid alloy would not give reproducible results in property determinations because of ex- cessive ß grain growth during heat treatment, a single ß grain frequently occupying the entire cross-section of a standard test bar. For this reason a commercial aluminum bronze containing iron as a grain growth inhibitor was used. The isothermal transformation diagram of the alloy was first determined. On this basis, the heat treatments necessary to produce representative structures were selected and the properties determined. Material A commercial alloy (Ampco Grade 20) of the following composition was used: Cu, 83.68 pct; Al, 12.31 pct; Fe, 3.68 pct; Ni, 0.28 pct; and Mn, 0.03 pct. This alloy proved to be very close to the eutectoid composition and may be compared with the accepted value of 11.8 pct A1 in the binary Cu-A1 system. Comparison is valid only because of the "negative replacement effect" of the iron? Since traces of excess y² are present, the alloy is slightly hyper-eutectoid. The material was received in the form of 3/4 in. round, hot extruded bars. Specimens of approximately ? in. thickness were cut from this stock and drilled to allow suspension in the salt bath. The structure of the as-received material varied from 5 to 40 pct a + y2* in a matrix of ß. The amount of a + y² present was dependent upon the ß grain size of the extruded material. The coarse grained portions did not form as much a + Y, as did

Jan 1, 1952

By Carl Benedicks

IT is well known by every one who has had to deal with boiler tubes that these are often seriously affected by a sort of corrosion, occurring as a local pitting, that frequently causes a perforation of the tube in a rather short time. The characteristic appearance of this corrosion is shown in Fig. 1. A very similar corrosion occurs in condenser tubes (Fig. 2).1 A study of the microstructure or local chemical composition of the metal (iron; 70 :30 brass) fails to reveal any cause for this pitting. Of course one might possibly assume the starting point-to be some oxide particle, causing an electrolytic local action, but this in no way explains the continued corrosion, progressing even when the assumed oxide particle must have disappeared. By the excellent work done by the Corrosion Research Committee of the Institute of Metals, and communicated, in October, 1923, to the Institution of Engineers and Shipbuilders in Newcastle-on-tyne, stress was laid on the fact that a content of entangled air has a very obnoxious effect. In the following correspondence, Sir George Goodwin stated that "engineers have, for a long time past, regarded air as the big enemy to be fought against in all questions of corrosion"2 and Kenneth Fraser pointed out that the most vital point is "the avoidance or removal of possibly the chief cause of present day corrosion, i. e. entrapped air and gases brought out of solution."' In their reply, however, the authors state that they had "never for a moment believed that entangled air was responsible for the beginnings of corrosion, and express the opinion that the gradual liberation of air could not account for localized corrosion."4 On consulting the many textbooks on corrosion, as that

Jan 4, 1925

By CHARLES R. KETES

I. INTRODUCTORY. Lake Valley, New Mexico, has long been one of the most widely known mining districts of southwestern United States. For many years its silver-mines have been among the most famous of the country, visited by many mining men and geologists; yet little information regarding the origin of the ore-deposits and the influencing geologic conditions has found its way into print. With the recent revival of public attention, after a decade and a half of utter stagnation, to the mining of silver in the Southwest, special interest attaches to the genesis and geologic disposition of the ore-bodies which are so finely open to inspection in the Lake Valley district. Moreover, the local features here described are typical of the conditions existing over a much larger field. The fact that the ores are chiefly the chloride and the chloro-bromide of silver adds further interest. Data bearing upon the genesis of haloid ore-deposits are, at the present time, very much sought. Arid regions offer particularly favorable conditions for the formation of such ores. This New Mexican district appears to supply solutions to many problems concerning this class of ores, which have long vexed the student of ore-deposits. II. LOCATION AND HISTORY. The town of Lake Valley is situated in Sierra county, in the southwestern part of New Mexico, and 100 miles northwest of El Paso, as the crow flies.From a mining standpoint, the location of the place is itself suggestive, as it lies on the southeastern slope of the great quaquaversal arch of the Colorado plateau. The center of this vast dome is in north-central Arizona, and radii about 150 miles in length reach its foot in all directions. Around its basal margins runs the broad mineralized belt containing most of the great mines of the Southwest, which extends from south-central Colorado southward and southwestward through New Mexico, thence westward through Arizona, northwestward and northward through southeastern California and western Nevada, and, finally, eastward through Nevada and Utah into Colorado again. This great mineralized belt is important as geographically limiting profitable mining over the greater part of five States.

Jan 1, 1908

The Bougainville ore body was discovered in 1964 by a partnership of Conzinc Rio Tinto of Australia and New Broken Hill Consolidated Limited. The ore body is a porphyry copper in a fine-grained quartz diorite, which intrudes andesite volcanics and is located at an elevation of about 2, 000 ft in the Crown Prince Range of Bougainville in the Solomon Islands. Mineralization is predominantly chalcopyrite with some bornite and some gold and silver present. Rainfall in the area amounts to 200 in. (5. 08 m) per year. An active volcano is situated only 24 miles (38.4 km) from the mine, and all structures were designed to resist seismic shocks. An interesting and unique feature of the Bougainville operation was that the overburden was stripped with hydraulic monitors. Bougainville Copper, at 90,000 tpd, is the largest copper concentrator to be designed and constructed at one time; and besides the twin 54 in. by 74 in. Allis-Chalmers gyratories, it features seven 7 ft (2. 13 m) standard and fourteen 7 ft shorthead crushers, in addition to nine 18 ft diameter by 21 ft long (5. 5 m by 6. 4 m), 4250 hp, single -stage ball mills. During the design stage of the Bougainville primary crushing plant, several alternates were studied because the ore was expected to break with the production of large amounts of small-sized particles but with a minimum of fines. These alternates included two 54 in. by 74 in. gyratories with grizzlies, two 60 in. by 89 in. gyratories, and one 72 in. by 96 in. gyratory, the latter two installations without grizzlies. The two 54 in. units with grizzlies were finally selected as giving good reliability and the ability to handle the large amounts of small material in the feed. As originally installed, grizzly bars were set at 8 in. (203 mm); but, in an effort to perform more interparticle crushing in the primary and less rock-on-steel crushing in the secondaries and tertiaries, a test is underway (1976) to determine the effect of using 6 in. (152 mm) grizzly spacings (see write -up on Anaconda's crusher at Butte). The Bougainville ore is mined with 17 cu yd (13 cu m) shovels and hauled in 105, 170, and 210 st trucks to the crushers, which are equipped for two-side dumping. Up to 40% of the ore passes the grizzlies, which are equipped with splitters; and additional horizontal splitter bars are located directly above the spider caps. Because of the grizzlies, the crushers are supported by unique U-shaped enclosures, which are in turn supported by the end and center walls of the installation.

Jan 1, 1978

By Edward C. Stephens, Robert R. Coats

High-grade copper ore was discovered in 1932 in the long-dormant Mountain City (Cope) mining district, Elko County, Nevada. From 1932 to 1947, the one producing mine in the district, the Mountain City Copper Mine, produced 1,109,878 short dry tons of ore averaging 9.745 per cent copper, 0.274 ounces of silver, and 0.0057 ounces of gold per ton. The Mountain City Copper Mine is developed in eugeosynclinal rocks of Ordovician age, the Valmy Formation, which is part of the upper plate of the Roberts Mountains thrust. On the Valmy were deposited unconformably first, a elastic formation of Devonian or Mississippian age, the Grossman Formation, succeeded unconformably by a ·sequence of three conformable formations, the Banner, the Nelson, and the Mountain City. The Banner Formation probably is early Late Mississippian in age; the ages of the Nelson and Mountain City are not known precisely but are believed to be of Late Mississippian and Carboniferous(?) age, respectively. A thick formation of elastic rocks, limestone, and volcanics, the Reservation Hill Formation, has been thrust over the Mountain City. The age of the Reservation Hill is unknown but is presumed to be Pennsylvanian(?) and Permian(?). Several plutons of Cretaceous quartz monzonite intrude the Paleozoic formations; they and the intruded formations have been laid bare by erosion, and several sequences of volcanic rocks of Miocene and Pliocene age, and perhaps in part older, have been successively deposited on irregular erosion surfaces. The primary mineralization of the Mountain City Copper Mine is believed to postdate the deposition of the Nelson Formation and to predate the intrusion of the quartz monzonite. The primary ore bodies are lenticular in shape and are composed largely of quartz, pyrite, and chalcopyrite. The ore lenses, in general, strike northwestward and dip northward. They occur in the Valmy Formation within a definite stratigraphic sequence composed largely of shales with associated minor quartzite lenses. The ore is epigenetic. The principal ore body, the "200," was completely leached to the 200 level. Abruptly beneath the barren gossan was supergene copper sulfide ore, much of which assayed 50 per cent copper. The secondary copper minerals are sooty and massive chalcocite, bornite, and covellite. The supergene enrichment of the ore may have required a large part of Tertiary time.

Jan 1, 1968

By J. Handin, S. J. Bauer, M. Friedman

Deformation mechanisms in room-dry and water-saturated specimens of Charcoal Granodiorite, shortened at 10-4s-1, at effective pressures (Pe) to 100 MPa and temperatures to partial melting (?1050°C) are documented with a view toward providing criteria to recognize and characterize the deformation for geological and engineering applications. Above 800°C strength decreases dramatically at effective pressures ? 50 MPa and water-weakening reduces strength an additional 30 to 40% at Pe = 100 MPa. Strains at failure are only 0.1 to 2.2 percent with macroscopic ductility (within this range) increasing as the effective pressures are increased and in wet versus dry tests. Shattering (multiple faulting) gives way to faulting along a single zone to failure without macroscopic faulting as ductility increases. Microscopically, cataclasis (extension microfracturing and thermal cracking with rigid-body motions) predominates at all conditions. Dislocation gliding contributes little to the strain. Precursive extension microfractures coalesce to produce the throughgoing faults with gouge zones exhibiting possible Riedel shears. Incipient melting, particularly in wet tests, produces a distinctive texture along feldspar grain boundaries that suggests a grain-boundary-softening effect contributes to the weakening. In addition, it is demonstrated that the presence of water does not lead to more microfractures, but to a reduction in the stresses required to initiate and propagate them.

Jan 1, 1982

By F. V. Lenel, G. S. Ansell, J. A. Dromsky

The growth of aluminum oxide particles in a nickel matrix was studied eve?. the temperature vange of 2140° to 2470°F. The instability of the dispersed alumina was shown to be independent of the crystal structure of the alumina. The activation energy for the growth of the dispersed alumina was found to be 84.7 1 2.0 kcal. The particle radius increased as a function of time. These results indicate that the growth is not diffusion controlled. It is believed that the rate controlling mechanism is the dissolution of the aluminum and oxygen atoms into the nickel lattice. THE strength properties of alloys which consist of a finely dispersed second phase in a metallic matrix depend upon the spacing between the second phase particles. It is therefore desirable to achieve very fine dispersions in these alloys. Furthermore, to retain the properties these very fine dispersions must be stable during fabrication and service of the alloys. The best known of the dispersion strengthened materials, the SAP type alloys, which consist of a dispersion of aluminurn oxide in aluminum, have exceptionally good stability up to the melting point of aluminum. There is evidence, however, that other dispersion strengthened alloys, even those consisting of refractory oxides in a metal matrix, may be less stable. This investigation is concerned with the stability of Ni-Al2O3 alloys in the temperature range in which these alloys are usually fabricated. The mechanical properties of Ni-Al2O3 alloys at elevated temperatures have been previously investigated by Crelnens and rant,' and Gregory and Goetzel.2 The behavior of these alloys in stress rupture tests appears to indicate that at temperatures below 1800°F they are highly stable. There is some doubt, however, as to their stability at the higher temperatures used during the conventional fabrication. Cremens and Grant, in preparing their test alloys, cousolidated, by powder metallurgical techniques, nickel powders as fine as 0.13 µ diam and alumina powders as fine as 0.018 µ. Metallo- graphic examination of the alloys following fabrication revealed that none had interparticle spacings of less than 2 µ. Considering the size of the original component powder particles, it is likely that the dispersions coarsened during fabrication. Gregory and Goetzel, in their studies of extruded alloys of 80 pct Ni—-20 pct Cr matrixes with nonmetallic dispersion, observed a definite coarsening of the alumina dispersions in alloys sintered at 2280°F as cantrasted to those sintered at 2000oF. Similar observations on the spheroidization and growth of thoria particles finely dispersed in a nickel matrix were made by D. K. Worn and S. F. Marton.3 As a result of such coarsening, much of the effort expended in the preparation of very fine powder mixtures would be lost. The mechanical properties of the alloys which had experienced coarsening would be expected to be poorer than if the original dispersions had been retained. EXPERIMENTAL PROCEDURE Ni-Al2O3 alloys were produced from powder prepared by a coprecipitation technique. Aluminum hydroxide and nickel hydroxide were coprecipitated from chloride solutions of the metals. The mixed hydroxides were calcined to form metal oxides and the nickel oxide in the mixture was selectively reduced to nickel by treating it in hydrogen. Specimens were compacted from the resultant powder which consisted of a fine, uniform mixture of aluminum oxide and nickel particles. The compacts were sintered by resistance hot pressing4, a densification technique which requires exposure times of the order of only a second or less at elevated temperatures. A conventional sintering process was not used, since the temperature required for densification would have to be in the region in which the stability of the dispersion was to be studied. A series of hot pressed specimens were treated in hydrogen at temperatures from 2140o to 2470°F (1171o to 1355oC, for times up to 120 hr. Changes in the microstructures were studied by electron microscopy using the two-stage preshadowed carbon replica method.5 In performing a lineal analysis on a series of micrographs from each specimen it was found more convenient to determine the mean free path between alumina particles rather than particle radii as the parameter of growth. Although these quantities are directly proportional for only spherical particles, the alumina particles in these alloys

Jan 1, 1962

By Nicholas J. Grant, Oliver Preston

PUBLICATION of data by Irmann' indicating outstanding thermal stability and elevated-temperature strength properties in a sintered aluminum powder product (SAP) stimulated interest in the strengthening of metals by means of a highly dispersed oxide phase. This material was produced by compacting, sintering and extruding a fine flake aluminum powder, resulting in a dense product containing 10 to 16 volume pct alumina, which arises from the thin oxide film on the starting powder, highly dispersed in a matrix of pure aluminum. The method of producing SAP, and the stable high-temperature properties obtained from it, introduced the possibility of developing superior materials for high-temperature service by powder metallurgy methods. The composition of the materials of this type which are presently under consideration is predominantly metallic, containing from less than 1 pct up to about 20 volume pct of the oxide. As a result, other properties of these materials, such as electrical and thermal conductivity, thermal shock resistance, and to a certain extent ductility, notch sensitivity, machinability and hot working properties, are also predominantly metallic. These alloys do not constitute, therefore, a completely new class of materials as do the cermets, but rather present a new means of modifying the properties of a metallic matrix. In this sense, SAP type alloys are more closely analogous to the alloy aging systems. While the strength properties realized in the oxide-pure metal systems at the lower temperatures are substantially less than the best attainable in the aging systems, the thermal instabilities in the latter make them of less value for use at temperature much above their optimum aging temperatures, as indicated in Fig. 1. While the means of obtaining an oxide dispersion are more difficult and costly than conventional aging processes, in the light of the as yet limited understanding of such systems there is considerable promise of improved high temperature properties arising from the thermal stability of these structures. Since the development of SAP in 1946, its properties and the properties of a series of similarAl,O,-A1 products containing from about 1 to 20 pct aluminum oxide have been fairly extensively studied and reported.'- "articular attention has been given to

Jan 1, 1958

By J. Blodget Britton

Six different samples of anthracite, each a firm compact lump, were finely pulverized and immediately put in bottles. Portions of these were weighed and placed upon an ordinary water-bath and dried for one hour; the average loss was 1.24. The same portions were then placed in a hot-air oven, and for two hours kept at a temperature of 285° F., and, after cooling in a dry chamber, were again weighed, when there was found a further average loss of 1.22, making a total so far of 2.46. They were then immediately returned to the oven and for two hours more kept at a temperature of 530° F. and cooled and weighed again, when no further loss was found, but an average gain of .55 upon the previous weighing. The same portions were a third time placed in the oven and for about ten minutes kept at the last-mentioned temperature, and then, while still hot, were poured into one-quarter inch glass tubes, each with a bulb at one end, and heated over a Bunsen burner at a temperature below a red heat, when more water vaporized and condensed in small clear globules on the cold parts of the tubes. Fresh portions of the coals were then taken, and the total amount of water determined, and the average was found to be 3.04, or 1.80 more than was found at the temperature of the water-bath, which was perhaps a little below 212° F., and .58 more than at 285° F. Tests were afterwards made by placing other fresh portions of the

Jan 1, 1877

By J. Blodget Britton

SIX different samples of anthracite, each a firm compact lump, were finely pulverized and immediately put in bottles. Portions of these were weighed and placed upon an ordinary water-bath and dried for one hour; the average loss was 1.24. The same portions were then placed in a hot-air oven, and for two hours kept at a temperature of 285' F., and, after cooling in a dry chamber, were again weighed, when there was found a further average loss of 1.22, making a total so far of 2.46. They were then immediately returned to the oven and for two hours more kept at a temperature of 530' F. and cooled and weighed again, when no further loss was found, but an average gain of .55 upon the previous weighing. The same portions were a third time placed in the oven and for about ten minutes kept at the last-mentioned temperature, and then, while still hot, were poured into one-quarter inch glass tubes, each with a bulb at one end, and heated over a Bunsen burner at a temperature below a red heat, when more water vaporized and condensed in small clear globules on the cold parts of the tubes. Fresh portions of the coals were then taken, and the total amount of water determined, and the average was found to be 3.04, or 1.80 more than was found at the temperature of the water-bath, which was perhaps a little below 212' F., and .58 more than at 285' F. Tests were afterwards made by placing other fresh portions of the

By V. V. Valleroy, A. J. Cornelius, B. T. Willman, G. W. Runberg, L. W. Powers

This paper reports the results of an investigation into the use of steam as a recovery agent. High oil recoveries by steam, as much as 100 per cent greater than by water flood, were demonstrated in laboratory linear cores. The principal mechanisms responsible for the additional oil have been identified as (1) thermal expansion of the oil, (2) viscosity reduction and (3) steam distillation. Although the first two also enhance recovery by hot water flood, they are effective with steam injection at lower volumes of produced fluids. Steam-zone residual oil saturation is independent of initial saturation. Recovery by steam is greater for lighter oils because they contain a greater fraction of steam-distillable components. Equations for the steam-zone advance in a radial homogeneous system are presented; these show the effect of reservoir parameters. The displacement in the hot liquid region moving ahead of the steam front can be estimated by a calculative procedure which is suggested. The method which takes account of the temperature gradient is applicable also to a regullar hot water flood. INTRODUCTION Considerable industry interest in the application of heat to petroleum reservoirs as a means of increasing oil recovery has been evident in the past few years. Three thermal methods which have attracted interest are (1) the injection of saturated steam, (2) the injection of hot water and (3) the injection of air into a formation to support combustion within the reservoir. Much has been published in recent years on underground burning, and there have been several papers on hot water injection. Although there are several early reports1,2 on steam injection, no recent experimental studies have been published on this recovery method. In our early thermal methods research, a marked improvement was found in oil recovery by steam injection compared with recovery by water injection in the same system. An investigation subsequently was undertaken to obtain quantitative information from which to evaluate steam injection as an oil recovery method. In addition, it was desired to investigate the recovery mechanism of hot water as compared with that of "cold" water and steam injection. An understanding of the mechanisms by which these processes operate would generally define favorable field conditions for their successful application. This paper reports the results of the laboratory study and suggests calculative approaches to estimate the field behavior of the steam-injection process. EXPERIMENTAL METHOD EQUIPMENT A schematic diagram of the equipment used for the displacement tests is shown in Fig. 1. Essentially, it consisted of a core with suitable means for recording temperatures, a feed system for injecting steam or cold or hot water, and a receiving train for condensing, cooling and measuring produced fluids. For the steam experiments, air-free saturated steam was piped from the boiler to the core face in insulated lines that were provided with steam traps and bleeds to remove any condensate formed in the lines due to heat losses. A 12-in. section of the line immediately ahead of

By Walter V. Knopp, Laurence Delisle

INTRODUCTION THE aim of this work was the preparation of nickel-steels from elemental metal powders by powder metallurgy techniques. It was known that plain carbon steels could be made from a mixture of iron powder and graphite and that the effect of carbon on iron in powder form was of the same nature as that produced in fusion metallurgy. The problem in making nickel steels from elemental powders consisted therefore in finding out whether sufficient diffusion of the nickel and other incidental metals normally present in such steels could be induced in the solid state to modify the properties of plain carbon steels made from powders and produce the beneficial effect of alloying. The composition selected originally was that of an S.A.E. 2330 steel. Metal powders, in the proportion corresponding to that composition, were mixed with graphite, pressed, and heated at different temperatures for different periods of time, to produce bonding of the metal particles and mutual diffusion of the various elements without melting. Temperatures up to 1325°C and sintering periods as long as 6 hr were first investigated because it was expected that such conditions would produce maximum diffusion with an accompanying improvement in the properties of the alloy. It was found that, although diffusion proceeded to a large extent under the conditions investigated, it would not be complete unless sintering were carried out at a high temperature for much longer than 6 hr. Relatively high temperatures and long sintering times are objectionable from a practical point of view, particularly when a low cost material is to be produced, because they necessitate the use of special, costly equipment. Work could be done to improve the diffusion of iron and nickel by changing conditions other than the sintering temperature and time, i.e., finer primary or alloy powders could be used. However, a marked change in the properties of the steel had been observed even with only partial diffusion. It was thought, therefore, that instead of trying to improve the diffusion, advantage might be taken of its incompleteness to produce a special structure consisting, in the unquenched condition, of a hard constituent, rich in nickel, dispersed in a tough pearlitic matrix. Steels with such a structure, not readily obtainable by fusion, should have desirable mechanical properties. Besides, it should be possible to prepare them from elemental powders under economical conditions. This latter alternative was therefore adopted for the second phase of this work. This report is divided into four parts: 1. General Procedure. 2. Effect of Sintering Temperature. 3. Effect of Varying the Nickel Content. 4. Effect of Alloying Elements. GENERAL PROCEDURE The general technique of cold pressing as used in powder metallurgy was applied.

Jan 1, 1948

By PAUL M. Tyier

NOW that analytical chemistry has gone so far to debunk early misconceptions about minerals, the fact that the light of exact knowledge still fails to illuminate many dark corners is often overlooked. By combining the skills of the physicist with those of a chemist, the identification of minerals has become an exact science and the presence of even minute traces of impurities and extraneous elements is readily revealed by spectrographic means, Granted that we can learn all there is to know about the composition of a substance and even about its physical propertied (which latter assumption is somewhat far-reaching) it still does not follow that we clearly understood its commercial designation or utility.

Jan 1, 1941

"The cleanliness and system evidenced in the accompanying photographs of the West Steward change-house will appeal to all mine operators. This design is the most efficient in use at Butte. It is the standard which will probably be used in Butte in all future construction and is the result of a long period of investigation and experimenting. It is important that such a structure be as nearly fire-proof as possible, because of the frequent fires originating within the lockers from matches, etc., in the men's clothes. The concrete floors permit the thorough washing of the building whenever necessary.The lockers are roomy and well ventilated. They are constructed of sheet steel and are warmed from below by steam pipes."

Jan 1, 1913

Correlation between Metallography and Mechanical Testing By H F MOORE (Henry Marion Howe Memorial Lecture Trans, vol 120 11,000 words ) The lack of effective correlation between metallography and mechanical testing from the days of Reaumur to the present is noted, and two general problems of such cor¬relation are stated (1) the correlation of qualitative test results with quantitative, and (2) the correlation of average results with maximum or minimum results Some correlation has been achieved, notably in the field of heat-treatment and in the study of elastic strength of metals Correlation is in the process of being developed in several other fields, including the quantitative study of the effect of grain size of metal on mechanical properties, of grain size and type of crystalline structure on the sensitivity of metals to weakening at holes, notches and other "stress raisers," and in the study of the starting phases of spreading, "fatigue" cracks Correlation of mechanical test results and metallographic study is needed in the study of such problems as the various theories of failure of metals, the meaning of and tests for service ductility of metals, and the relative damaging effect of defects inherent in metals, such as minute cracks and segregation, as compared with the damaging effect of "imposed" stress raisers, such as screw threads, sharp shoulders, etc The neces¬sity for more correlation of metallography and mechanical testing during student days is emphasized, and also the need of a better understanding on the part of engi¬neers of the significance and limitations of metallographic apparatus and results and of X-ray diffraction This should be matched by a better understanding on the part of metallurgists of the significance and limitations of mechanical tests of metals, of testing machines and strain-measuring apparatus

Jan 1, 1937

By Klaus Schwerdtfeger

Activities of lead in Pt-Pb and Pd-Pb melts in the temperature range of 800° to 1200°C have been detev-mined from electromotive-. force measurements 202th the cells Both systems display strong negative deviations from Raoult's law. The data obtained with cell [1] were combined with available data on the activity of PbO in silica-satuvaterl PbO-SbO2 melts to calculate the standard free cnergy of formation 01- liquid PbO. FREE energies of formation of oxides and activities of components in metal and oxide melts can be determined with galvanic cells consisting of a metal phase, an electrolyte containing the oxide of one of the components of the metal phase, and an oxygen electrode. This technique has been used previously to measure the standard free energy of formation of solid sio2, 1 and activities in Fe-si, CO-si,2 Ni-Si,2 and CaO-P2O5 3 melts. The present paper reports activities in Pt-Pb and Pd-Pb melts as measured with the same experimental technique. EXPERIMENTAL METHOD General Considerations. The following cells were used: Pbl (PbO-SiO2)liquid, SiO2 Pt-Pb 1 (PbO-SiOz)liquid, SiO2solidO2 [2] Pd-Pb (PbO-SiOz)liquid, SiO2solid O2 [3] Liquid alloy and' oxide melt were contained together in a silica glass crucible of essentially the same design as described previously.1'2 The PbO-SiO2 melts are ionic conductors.' During the experiment, the silica glass crystalizes in a layer adjacent to the electrolyte. The electrolyte equilibrates with solid silica and hence attains the composition of the Si02-liquidus curve in the system PbO-SiO2 at any particular temperature. Molybdenum wires were used to establish contact with the liquid metal. The oxygen electrode, which reaches the surface of the PbO-SiO, electrolyte from above, consists of a platinum wire inserted into a ceramic tube and provided with a 2-mm-diam platinum bead at its end. Gas of known oxygen partial pressure (pure oxygen of 1 atm: air, or N2 with 1.04 pct 0,) is blown through the ceramic tube onto the surface of the electrolyte. The cell reaction is Pb (metal) + 1/2O2 (gas) = PbO (electrolyte) [4] No oxidation of platinum or palladium ("displacement reaction") occurs. This is to be expected from the noble character of platinum and palladium, but was also shown experimentally, as described in the next section. The galvanic electromotive force of the cell is given by where AG is the change in free energy for Reaction [4], E(=2) is the number of electrical equivalents necessary to form 1 mole of PbO, and F is the Faraday constant. Formula [5] is valid only if no junction potential exists within the electrolyte. Junction potentials occur only when the compositions of the electrolyte are markedly different at the electrodes. Such differences are negligible in the PbO-SiO, electrolyte, as shown in the next section. Since molybdenum contact leads are used, appropriate corrections were made on the measured electromotive forces to account for the thermoelectric effect of the Mo-Pt couple. The thermoelec-tromotive forces were measured separately with a Mo-Pt couple, and were found to vary linearly from 19 mv at 740°C to 40 mv at 1310°C with molybdenum being positive and platinum negative (cold junction at 25°C). Extrapolation of these values to higher temperatures yields values which are in satisfactory agreement with those obtained previously in the temperature range 1440° to 1630°c.1,2 The change in free energy for Reaction [4] is expressed as where chemical potentials of the species. The value of constant for a given temperature because the slag composition is fixed. Inserting [6] into [5] and using appropriate expressions for upb and uO2 the relation

Jan 1, 1967

By H. C. Fiedler

Heats of high purity iron containing 3.1 pct Si and be -tween 0.0003 and 0.0295 pct N were prepared by vacuum melting ad then pouring while in a nitrogen atmosphere with the pressure between 0 and 90 psi. Strip from a heat with 0.0184 pct N underwent complete secondary recrystallization during the final anneal. Heats with less nitrogen had too few Si3N4 particles to restrain normal grain growth, and the heat with higher nitrogen had too many particles to allow complete secondary recrystallization. In the hot-rolled structure, Si3N4 precipitates only at the grain boundaries, with the consequence that annealing after hot-rolling diminishes the ability to subsequently undergo secondary recrystallization. In contrast to this behavior, ALNprecipitates uniformly in the hot-rolled structure. Under 1 atm of nitrogen, Si3N, in 3.1 pct Si-Fe dissociates between 900" and 950°C; the solubility of nitrogen increases from 0.0010 pct at 900" to 0.0030 pct at 1200°C. The solubility of nitrogen in Si-Fe has been the subject of many investigations. Corney and Turkdogan1 heated a 2.83 pct Si alloy in nitrogen and found the solubility, under 1 atrn of nitrogen, to be 0.0019 pct at 900°C. They claimed that Si3N4 did not form in the alloy above 705°C in 1 atrn of nitrogen. Fryxell et al.2 heated samples of 3.25 pct Si-Fe containing 0.0025 pct N over a range of temperatures and then analyzed for total nitrogen by vacuum fusion and for nitrogen in solution by a modified Kjeldahl technique. At 900°C, they reported the solubility of nitrogen in equilibrium with Si3N4 to be 0.0011 pct. pearce9 found the solubility of nitrogen at 900°C under 0.95 atrn of nitrogen to be 0.0017 pct in a 3.06 pct Si alloy. He reported that Si3N4 does not form above 770°C in 1 atrn of nitrogen. Although internal friction measurements have given somewhat higher values for the solubility,4-6 if the solubility of nitrogen is as low as has been reported by most investigators, and if Si3N4 is stable up to at least 945°C at 1 atrn pressure of nitrogen as reported by Seybolt,7 a small amount of nitrogen in properly processed Si-Fe should be effective in promoting secondary recrystallization. The requirement is that in the final heat treatment there be enough small, well-dispersed particles of Si3N4 to restrain normal grain growth. Fast8 has obtained secondary recrystallization by nitriding high-purity 3 pct Si-Fe after hot-rolling to a thickness of 0.118 in., followed by processing to 0.012 in., and annealing. A large amount of nitrogen, 0.076 pct. was introduced during the nitriding heat treatment, but he has since reported9 that "a few hundredths of a percent" is sufficient. Small amounts of aluminum10 or vanadium" nitride are capable of promoting secondary recrystallization. Heats containing as little as 0.010 pct A1 or 0.042 pct V and from 0.006 to 0.009 pct N underwent complete secondary recrystallization at final gage, whereas heats with lesser amounts of aluminum or vanadium did not.l2 To be reported is the behavior of nitrogen in high-purity 3.1 pct Si-Fe, and the relation of this behavior to the ability to undergo secondary recrystallization. PROCEDURE Ingots weighing 1 lb were made by vacuum melting high-purity electrolytic iron (A104, Glidden Co.) and high-purity silicon (Monsanto Co.). The latter was used in preference to ferrosilicon to insure a low aluminum content. The design of the melting furnace permitted pouring with the furnace atmosphere either below or above atmospheric pressure. Accordingly, at the completion of melting, nitrogen was admitted to the desired pressure and the heat then immediately poured. The ingots were sound, with no indication of porosity. In Table I are listed the heats investigated, the nitrogen pressure at pour, and the nitrogen and oxygen contents as determined by vacuum fusion with a platinum bath at 1850°C, a procedure which insures measurement of the total nitrogen.13 In addition, all heats contained 3.1 pct Si and not more than 0.002 pct C, 0.003 pct S or 0.005 pct Al. It was subsequently found that the quantity of nitrogen contained in the heats in Table I does not necessarily represent that obtained under equilibrium conditions. For example, the ingot poured immediately after 1 atrn of nitrogen was admitted to the chamber contained 0.0093 pct N, whereas an ingot poured 3 min after the nitrogen was admitted contained 0.021 pct N and another poured after a 6-min delay contained 0.029 pct N. While some bleeding of the hot top occurred in the latter instance, the ingot when examined in cross section appeared sound. The ingots were heated to 1325°C in hydrogen and rapidly rolled to 0.080 in. in 3 passes. The roll speed of the final pass was reduced so as to increase the quenching effect of the rolls. The hot-rolled pieces were processed both as-hot-rolled and after heating for 3 min at 900°C in hydrogen. After cold-rolling to 0.026 in., the strips were heated for 2 min at 900°C in hydrogen, then cold-rolled to the final gage of 0.012 in. The loss of nitrogen in going from the ingot to cold-rolled strip was no more than 10 pct. The final heat treatment, which was for the purpose of develop-

Jan 1, 1970

By R. A. Mosser

Production control of aluminum content of low carbon aluminum killed open hearth steels is being achieved by using an oxygen probe unit. Based on the free oxygen content of the bath after block, a preliminary chart for aluminum additions has been established. The aluminum aim is .040%. Controlled aluminum contents will result in eliminating coarse grain heats, high aluminum contents, and a reduction in aluminum costs. By reducing the frequency of high aluminum contents both cleaner and better rolling heats will be obtained. The savings in aluminum costs is an added benefit of lesser importance in comparison to the quality improvements gained by controlled aluminum contents. Although the main goal for the oxygen probe at Republic Steel has been to adapt it for production control of aluminum contents, future usage could be extensive. Immediate plans for using the probe are on degassed material, on fully blocked open hearth heats to improve manganese recoveries and ranges, and on machining grades to control oxygen content. Also by controlling the oxygen content of the steel to as close to equilibrium conditions as possible, cleaner steel will result.

Jan 1, 1972