Search Documents

By Will Mitchell, Ford F. Miskell, C. L. Sollenberger

Heat treatment of ore prior to comminution reduces power requirements for grinding, reduces grinding media wear, and improves recovery of iron values from a typical Minnesota magnetic taconite. Test data demonstrating this, as well as an analysis of the economics of commercial application of the technique, are presented. THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators1-" ave noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilitiesh nd by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat- treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported7 to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of' this portion is shown in Table I and an approximate mineralogi-cal analysis is shown in Table 11. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of —6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1953

By Benjamin C. Greene, H. Beecher Charmbury

Water is a most remarkable substance, essential for life of all kinds. As well as needing water to survive, man has always used it for agriculture, transportation, recreation, and many other things. When our country was young and inhabited by few people, the streams, rivers, and lakes were able to provide all the clean water needed by man and take away all the wastes created. However, with our growing population and an ever-increasing demand for goods and services, the public, industry, and government at all levels have become acutely aware of the need to manage the nation's water resources more efficiently. Abundant energy from many sources has helped this nation to become the greatest industrial nation in the world. Coal has contributed a major portion of this energy, generating electricity, running railroads, and maintaining national security during wartime. The result has been the highest standard of living in the world and a time of widespread economic prosperity. The use of water in coal mining is somewhat different from its use in most industries. With the exception of water used in cleaning plants, for underground dust control, and for fire protection, most of the water en- countered in coal mining operations serves no useful purpose. In other words, it is an undesirable element and must be removed, otherwise it will interfere with operations, cause potential water quality problems, and may even stop operations by flooding. In the past, removing water from working areas of most mines was usually a fairly simple matter. Pumps with piping were installed at sumps or low spots in the mine and the water was pumped to the surface or to drainage control facilities constructed for the operation. Ditches were often used to collect and drain the water by gravity to the outside or to main sumps for pump discharge. In either case, the water was allowed to flow into the nearest stream or river. The concept of "water is water'' was generally accepted without too much concern for what was in

Jan 1, 1981

By Charles Albert Ashburner

THE stratigraphical geology of the vicinity of Buffalo has always been of great interest on account of its bearing on the origin and history of the Niagara-river gorge, between the Falls and Lake Ontario. Recently, however, the character and thickness of the strata which underlie Buffalo have acquired more practical and economic importance on account of their relation to the possible occurrence of natural gas in commercial quantity near the Niagara river. In a paper presented at the Duluth meeting (l887), on " Petroleum and Natural Gas in New york State" (Trans., xvi., 906), I gave a brief description of the four wells which had been drilled by the Buffalo Cement Company between 1883 and that time. One of these wells is 1305 fret deep; and, at the time that my paper was finally revised for the Transactions (June, 1888), it was still an open question whether the drill in this well had reached the Niagara limestone, or had penetrated the Medina sandstones and shales, which latter are boldly exposed in a number of localities in the district, hut more particularly along the Niagara river in the vicinity of Lewiston and Qneenstown. The difficulty in this geological question at Buffalo has lain in the fact that no reliable determination could be made of the thickness of the strata included between the Corniferous limestone, immediately below which the drilling of the Buffalo gas-wells was commenced, and the Niagara limestone. On the other hand, the strata included between the latter limestone and the middle portion of the Medina sandstones and shales, have been minutely measured and studied in the Niagara gorge below the Falls by many American and European geologists. The first reliable section of these strata was constructed by Professor Eaton, and published in 1824 in his report on the Geological and Agricultural Survey of the District adjoining the Erie Canal. This section, extending from Lake Erie to Lewiston, is complete, with the exception that no thickness is given to the Salina or Onoudaga salt group,

Jan 1, 1889

By E. P. Mathewson

THE experiments described in this paper were made at the Washoe Reduction Works, Anaconda, Mont., for the purpose of determining the relative speed of elimination of the iron, sulphur and arsenic during the process of bessemerizing copper-mattes. The samples were taken from a horizontal "barrel" converter, 8 ft. in diameter and 12 ft. 6 in. long, having an average charge of 9 tons of matte, and blown with a 16-1b. air-pressure. All samples were taken with the blast on, turning the converter from its normal blowing-position to nearly verti¬cal, so that a conical mold, with a long handle attached to a horizontal rod, could be introduced from a platform above the converter into the mouth of the converter and a sample taken. The difficulties of taking a sample with the blast on are appar¬ent, and the irregularities of the lines in Figs. 1, 2 and 3 can be readily accounted for by the amount of slag in the samples. On the whole, the plotting of the results gives comparatively uniform lines, considering the conditions. The samples were taken by the regular sampling-force of the works at 10-min. intervals, as shown in Tables I., II and III, which also give the chemical analysis of the samples so taken. The test shown in Table I. was made with a new converter; that of Table II with a converter that had made three charges and had been cleaned out; that of Table III with a converter that bad blown one charge to white metal, and had then been " washed " out and used for the test. In plotting these results, it was necessary to take, as a basis, the percentage of copper in the samples. This basis does not exactly represent the true condition, since the volume is constantly decreasing and a certain quantity of copper passes into the slag, but it is as near as can be obtained in practice. Take, for instance, in Table I., the sample No. 5, which shows : Cu, 59.9;

Jan 1, 1907

By Thomas C. Wilder

ALTHOUGH there is an abundance of thermodynamic information available in the literature today, no experimental data on the standard molar properties of formation of zinc oxide have ever been reported for the temperature range 419.5" to 908°C. This is the temperature range for which zinc metal is a liquid. so that the formation reaction is: Data have been reported for Reaction [I] where zinc is a solid or a gas. Maier. Parks, and nderson' measured the electromotive force of the cell: in order to obtain the free energy of the reaction: over a limited temperature range. With the known properties of H2O, those of ZnO were calculated. These workers found that t;j of ZnO is -75,930 ± 150 cal per gfw and Mtf is-83,000 300 cal per gfw at 25°C. akolkin made similar measurements to obtain ilF7 and AH; of -75,870 and -82,540 cal per dw respectively at the same temperature. Truesdale and arirlg and Kitchener and 1gnatowicz4 measured the equilibrium of the reactions: respectively, in order to determine Ff of ZnO from the known values of CO, CO2, and H/X The thermodynamic properties of ZnO, presumably taken from the above investigations, are tabulated by Kubaschewski and vans' and Wicks and Block" The latter reference also gives values for the range where zinc is a liquid. These numbers are probably acquired from the known extremities of the range plus Cp data of the components. In the present work the electromotive force of the cell: was measured in order to calculate the properties of ZnO from the well known values of NiO for the temperature range where zinc is a liquid. In Cell [B] the cathode reaction is: and at the anode: The overall reaction is: for which the free energy change is: where is the electromotive force in volts of cell [B] after correction for the Pt-Ta thermocouple. The standard molar free energy of formation of NiO is very well known as a function of temperature. Kiukkola and agner's data are used in most tabulations. The error is probably less than I00 cal per gfw, The latter authors were the first to use solid mixed oxide electrolytes in galvanic cells. Their work with NiO and other oxides was performed with cells similar to Cell [B] using a variety of reference electrodes of fixed oxygen potential. There may be a small composition range for which either NiO, ZnO or both exist. If nonstoichiometry does exist for these oxides, then the properties described herein are those for the metal saturated compositions. The simple cell design was the same as described elsewheres except that the molten metal electrode was about 125 g of pure zinc including a small (0.25 to 0.50 g) amount of ZnO. The mixture of pure nickel and NiO powders making up the reference electrode was contained in a tube of the ZrOl + CaO electrolyte which was immersed in the molten zinc. A platinum contact was made to the reference electrode; tantalum to the zinc. A refractory cement plug was necessary at the open end of the electrolyte tube in order to prevent zinc vapor from contaminating the reference electrode. Experimental details such as the vessel containing the cell, furnace, temperature control and measurement, and electromotive force determinations of the cell have all been outlined previously. The temperature was varied randomly in the range between the freezing and boiling points of zinc. After each temperature change, time was allowed for the drift at the new temperature to be less than +;"c whereupon a series of three cell readings was taken at least 10

Jan 1, 1970

MINING and Metallurgy closed the year 1928 showing a small profit, the receipts, exclusive of the charge against members, dues for subscriptions, having been $43,067.81, and expenditures $40,925.58. In accord with the policy of the Board the budget is made each year with the purpose of balancing the accounts rather than the maximum of profit from the undertaking since it is the service the journal performs for members that justifies its existence. This service is being constantly increased. Within the year a number of changes have been made in the dress of the magazine, a new cover adopted, color more frequently used, and illustrations more generally employed. These changes seem to have been appreciated both by readers and advertisers. More space has been devoted to papers read before local sections and to the news of their activities. It is believed that this has helped materially in sustaining and increasing the interest in such meetings. The general, regional, and division meetings have also been fully reported and news of Board meetings, of the work of the various committees, of the employment service and other activities of the Institute has been spread before its members month by month. The 570 pages of reading matter printed in the course of the year constitute not only a record of what the Institute was doing but of what the most representative sections possible of the members of the mining and metallurgical professions were thinking. With 9000 members scattered around the world, occupying key positions in the industry, the Institute affords through its own journal an unsurpassed medium for broad contact and enables the readers with the minimum of expenditure of time and at no extra money expense to keep a general contact with the whole range of subjects touched by miners and metallurgists. In these days of intense specialization but rapid change such contact is particularly valuable. The more formal papers presented to the Institute are published in the Transactions, Technical Publications and the special volumes. Mining and Metallurgy carries abstracts of all papers published ,by the Institute and prints in full the shorter, less detailed papers and those which reflect work in progress rather than finished. Such papers have a news value which is supplemented by editorial comment, discussion by members and others, and the actual news of the organization itself. Without therefore attempting to fill the place of a general news sheet, it has a timeliness that gives it an immediate value much appreciated by the readers. In accord with the general policy of the Board every effort will be made constantly to improve the quality of the magazine to the full extent that its revenue will permit. Your Committee feels that, through the intelligent cooperation of the official staff in the office, Mining and Metallurgy has been improved in

Jan 1, 1929

By N. E. Grosvenor

Several methods have been proposed for determining the tensile strength of rock. These have been tried out over the past several years, but the results have been erratic and of doubtful value. The tensile strength of rock is its weakest property, and this property apparently enters into all failure phenomena, whether underground or on the slope of an open pit. Therefore, it is essential that detailed quantitative information is known about the tensile strength of rock if the design engineer is going to select the proper pit slope, pit orientation, or orientation of underground workings so as to give the most economical and safest mining condition. This quantitative information may be used to orient the pit in such a manner as to allow steep slopes along two sides. This information possibly may be used to orient the direction of either underground workings or open pits so as to decrease powder consumption and to increase blasting efficiency. Hence it is of prime importance that a method of determining accurately the tensile strength of rocks be developed. The U. S. Bureau of Mines states' that no standard methods have been proposed by the ASTM for testing the tensile strength of rock. The method described in the Bureau publication is said by them to be unsatisfactory. A similar test that has been used in our laboratory in place of the USBM test is shown in Figs. 1 and 2. h this test the core is placed in a set of grips that has been designed for one particular size core. The grips are designed to distribute the stress around the core if they are tightened correctly. A universal joint or a flexible cable may be used in conjunction with the apparatus to prevent bending or twisting of the specimen. The main difficulty encountered with the system shown is the failure of the specimen within the grips. The possible cause of the failure within the grips may be due to a stress concentration set up by the uneven tightening of the grips. This method can be used only for tests on cores, and even then has been found to be totally unsatisfactory because of the failure within the grips. The U. S. Bureau of Reclamation has been using a test similar to the sketch shown in Fig. 3. Sulfur is cast around each end of the specimen to form a bearing surface and then a ring grip is used to apply a tensile stress. The grips are in contact with the sulfur cast and do not touch the specimen. This method is unsatisfactory, apparently because a large number of the specimens appear to break within the sulfur cast. Professor Wuerker of the University of Illinois uses the test shown in Fig. 4.' Professor Wuerker states2 that this method has given definite and reproducible results with the weakest as well as with the strongest rocks. The test is a supplement in all cases where cores cannot be obtained. The principle and equipment are the same as for the test for tensile strength of hydraulic-cement mortar. Soft

Jan 1, 1961

C. P. BOWIE, San Francisco, Cal.-In my work with the U.S. Bureau of Mines, I have been detailed to report on oil storage containers, and in going around the country I have, been much interested in, the possibilities in the use of concrete for such containers. In talking with a good many people, I have discovered that concrete is being used A good deal for a wide variety of oils ranging from 14° to as high as 40° Bé., especially, by some of the western railroads:, If any member has had experience, in storing gasoline in concrete, I should like to learn of it. DORSEY HAGER, Tulsa, Okla.-Mr. M J. Munn, formerly .with the U. S. Geological Survey, acid connected with the Gypsy Oil Co., until a short time ago, has invented a invented a method for the application of concrete to the storage not only of crude oil but of refined products:. The Cosden Oil Co., of Tulsa, is now working on that plan, and, expects to store refined products in concrete tanks. THE CHAIRMAN (I.N. KNAPP, Ardmore Pa.).-I have had considerable experience in building masonry tanks for gas Holders. I do not believe it is possible to build a concrete or masonry tank of any kind. With hydraulic cement, mortar, which will be absolutely water-tight, unless the bottom and inner wall, after completion are waterproofed with some impervious material. The same will be true of oil tanks, the bottom and inner face of which must be made impervious to oil. Masonry tanks are intended to be sunk in the ground. All that the wall of the tank then amounts to is a retaining wall to keep the excavation in shape and to receive an impervious coating. The bottom of, a; tank, when empty, must be protected by a relief valve from any hydraulic: pressure acting from below. At ordinary prices, for sheets, a tank 100 ft. diam by 20 ft. deep can be built of steel much quicker and cheaper than of masonry. Several years, ago I saw very large oil storage tank under construction in California the bottom and sides being concrete. The sides were, sloped at about the single of repose for the material excavated: If you build a steel oil tank, you can get. .men for the work who do nothing else, and you, are likely to get a satisfactory job; but if you wish to build a concrete or masonry tank it is almost: impossible to find men skilled in building absolutely water-tight masonry Work. The general idea is that any laborer can mix up concrete in any old way and make a,

Jan 1, 1918

By A. L. Labbe, J. J. Donoso

Hard-won experience in the operation of smelting plants has pointed the way to the most efficient design and economical operation of a baghouse system for recovery of metallurgical fumes. This paper treats of the principles governing bag filtration and the factors most directly affecting bag life. Methods for temperature conditioning of smoke previous to filtering are described and the evolution of bag shaking mechanisms is brought up to date. THE history of the bag filter process, as applied to the recovery of metallurgical fumes, goes back to 1876, when the Lone Elms Works of Joplin, Missouri, erected a two-section baghouse for filtering fumes from Scotch Hearth lead smelting furnaces. By modern standards this installation was crude, but the basic operating principles remain essentially the same today. Great progress, however, has been made in the mechanization of the process by the use of devices for mechanically and automatically cleaning bags of adhering fumes, in the use of instruments for recording and controlling the variables affecting baghouse operation, and in the conditioning of the smoke previous to filtering. The principles governing bag filtration of fumes were investigated in 1929 by A. J. Seitz of American Smelting and Refining Co., and he arrived at the following conclusions: 1. Pressure on Bags at Constant Volume: The rate at which the pressure builds up in a bag with constant volume is directly proportional to the time, with the same kind of smoke and dust burden (fig. 1). 2. Pressure on Bags for Change in Volume: With equivalent smoke and dust burden, the bag pressure increases with the square of the increase in volume. The rapid increase in pressure is due to (1) increase in volume, (2) increase in amount of dust on the bag, and (3) more intense packing of the dust at higher velocity (fig. 2). 3. Effect of Intensive Filtering on Pressure: Since the pressure builds up directly as the square of the volume, with the same smoke and dust burden, it is necessary to shake the bags in that increased ratio, and vigorously, to keep the pores of the bag open and pressure down. This increases the wear on the bags and the dust losses. 4. Effect of Shaking on Dust Losses: The losses are in direct proportion to the frequency of shaking because the loss takes place immediately after shaking, before the bag seals itself. Tests show that with hand shaking the last 20 pct of the removable dust requires seven times more shaking per unit weight of dust than the first 80 pct. 5. Effect of Fineness of Dust on Losses: The fineness of the dust particle increases the loss in two ways: (1) When the bag is clean a greater percentage of it will pass through before the bag seals itself; (2) fine material penetrates farther into the bag pores, building up pressure faster and necessitating more shaking, thereby increasing the loss. The physical principle of operation of the bag filter is simply the separation of solids from a gaseous carrier through a porous medium, and is analogous to the filtration of solids from liquid carriers. Basically, the mechanics of the process are as follows: Fume-laden gases drawn from the operating fur-

Jan 1, 1951

By C. W. Dunham

FROM the primary gyratory crushing plant, described in MacLeod's article, ore is delivered to a large storage or surge bin from which it is carried by two transverse conveyors to the secondary crushing plant. The bin has a useful drawoff of about 13,000 tons, this being slightly over one half of the initial daily capacity of the Morenci Reduction Works. This arrangement provides sufficient storage to permit intermittent operation of the primary and secondary crushing plants without too close a coordination between the two.

Jan 1, 1942

By S. J. McCarroll

Fig. 1—The belt shown at right carries filter cake to mixing station over calciner. Crude ore conveyors appear in right background. THE Three Kids mine, some six miles east of Henderson, Nev., is in a typical southwest desert area, with high dry summer heat and cool to cold winter seasons. The manganese deposit was located during World War I.' During this period 15,000 to 20,000 tons of ore assaying up to 41 pct manganese were shipped. Interest in the deposit was not revived until the middle thirties, when experiments on the ore were initiated. Test work indicated possible recovery of only 70 pct by flotation, but in 1941 additional work was done at the Boulder City pilot plant of the U. S. Bureau of Mines and also by M. A. Hanna Co. As a result, the Manganese Ore Co. was formed and a plant utilizing the SO2 process was constructed. Numerous operation difficulties ensued, and the plant. was closed when the manganese situation in the country eased. In 1949 Hewitt S. West initiated negotiations to acquire the plant. In 1951 Manganese, Inc., was formed and contract entered into with the General Services Administration to supply 27 million units of metallurgical grade manganese in the form of nodules to the national stockpile. A second contract was made to upgrade 285,000 tons of stockpile ore. Test work was undertaken by the Southwestern Engineering Co. and likewise by the Boulder City pilot plant at the U. S. Bureau of Mines. Results obtained indicated the commercial feasibility of the flotation process. Construction of the plant, which is shown in Figs. 1 and 2, was started in June 1951, and operations on a break-in basis began in September 1952. Apart from the usual starting difficulties two major disasters caused serious setbacks, one a kiln failure in February 1953, and the other a fire that destroyed the flotation building in June of the same year. The nodulizing section of the plant resumed operation in November, and the flotation section in January 1954. The ore minerals are chiefly wad,* with minor amounts of psilomelane, and occur in sedimentary beds of volcanic tuff. The ore is overlain with beds of gypsum which outcrop or may be covered with surface gravel. Intermediate beds of red and white tuff occur frequently with lenses of red and green jasper and stringers of gypsum and calcite. Small amounts of iron are present; lead content averages about 1.0 pct and minute amounts of copper and zinc are found. Barite, celestite, and bentonite are present. Since these are made up of minute asicular crystals, moisture content is very high, averaging about 18 pct. Ore reserves have been estimated at 3 million tons averaging 18 pct Mn2 and up to 5 million tons after grade is dropped to 10 pct Mn. A good part of the orebody was stripped of overburden by the previous operating company . Approximately 50 pct of the ore, representing more than 60 pct of the manganese, can be mined by open-cut methods. A system for underground min- . ing has not yet been decided on. Open-cut mining with benches of 20 ft has proved satisfactory. Although the ore is soft and appears dry and dusty it has a certain resilience, probably due to the porosity and moisture which makes drilling and fragmentation difficult. Wagon drills have been abandoned in favor of the Joy 225-A rotary drill which will put down a 43/4 -in. hole at the rate of 2 ft per min. Holes are spaced in a pattern with 8 to 9-ft centers. Forty percent powder has been used, but better breaking to 2-ft size is obtained with low velocity bag powder of 30 pct strength. Loading is done with one 21/2-yd shovel, and cleanup follows with one D-7 bulldozer. The ore is hauled with Euclid trucks about 1000 ft from the pit to a blending pile, where the daily mine production is spread in layers by bulldozing until approximately one month's mill feed is accumulated. A new pile is then started and mill feed is drawn from the first pile by one 13/4-yd shovel and Euclid trucks, with a haul of approximately 500 ft. Mining is performed by an independent contractor with engineering and supervision by the company staff. Early test work indicated that the manganese could be floated with soap, a wetting agent, and fuel oil to give a recovery of better than 75 pct with a grade of 43 pct Mn. The concentrate when nodulized with coke would upgrade to 46 pct Mn or over, and the lead volatilized to 0.6 pct residual.

Jan 1, 1955

By Paul B. Crawford, Melvin B. Burton

A procedure is given which describes how the gelatin model may be-used to study the effect of mobility ratio on areas swept before and after breakthrough in fluid injection programs. Differences in mobility ratio are achieved through the proper selection of electrolytes for the invading and displaced fluids. The progress of the front is followed visually and photographed or traced onto plates (it desirrd positions before and after breakthrough. Example applications to standard flooding pattrrrls, vertically and horizontally fractured reservoirs and the in-situ combustion recovery process ore presentrtl. INTRODUCTION In water flooding, gas cycling and other fluid injection programs, the sweep efficiencies and swept areas after breakthrough are known to depend on the mobility ratio. Previous investigators have described the application of the X-ray technique, stepwise use of the poten-tiometric model and numerical procedures for studying these problems.1,3,4,6 Others have described the application of the electrolytic and gelatin models for studying sweep efficiencies at a mobility ratio near one.2,5,7,8,9 It is a purpose of this paper to describe a procedure for using the gelatin model to study swept areas at mobility ratios other than one. PROCEDURE The technique developed for gelatin model studies is composed of four phases: the construction of the model, the selection and preparation of electrolytes, the running procedure, and the recording of the swept areas. Each phase is discussed independently in order that the over-all procedure will not be confused. Construction of the Model Since some of the advantages of the gelatin model are its economy, and speed, it is desirable to have as small a model as is possihle without creating error through the inability to follow visually the progress of the colored front. For this work, it was found that a distance of 4 to 6 cm between salt bridges is convenient to use. Since the size is relatively small, it follows that the gelatin layer must be thin. For this study, 1/8 in. was used as the gelatin thickness in each case. The model was constructed on a flat 1/2-in. plastic (Lucite) base with boundaries constructed from 1/8-in. plastic strips. The well pattern to be studied was outlined with the 1/8-in. plastic strips on the base with narrow apertures (- - 2 mm) in the boundary to represent the wells. Behind each well opening, a rectangular area of some 8 to 12 sq cm was outlined by additional plastic strips. The plastic strips were fastened to the base by any suitable non-conducting cement so that the boundary system was liquid tight. The electrodes were constructed from sheet copper in a fashion that would allow easy removal. In this work, it was found that by simply forming a large U-shaped clip from a strip of the copper that would slip over the boundary was satisfactory and easily removed. The electrodes should be as wide as one of the sides of the rectangular area behind the well opening. If a fractured pattern is studied, fractures inside the well pattern may be represented by strips of copper of the desired shape mounted in some easily removable fashion. The reason that apertures (or salt bridges) were used for wells instead of metallic electrodes is that the plating of the electroactive ion at the cathode and the introduction of an electroactive ion at the anode has a detrimental effect on the swept area outline if these operations \rere permitted to be carried on within the well pattern itself. The anode may be used within the well pattern

Jan 1, 1957

By E. P. Polushkin, Henry L. Shuldener

This paper describes the results of microscopic examination of a series of brass pipes removed from apartment and office buildings in New York City, adjacent localities on Long Island, and Philadelphia. They were selected as typical of approximately four hundred pipe specimens obtained over a period of five years during an investigation of corrosion in hot-water installations. A part of the investigation is reported in this paper and includes a brief history of the pipes, a description of their inside surface and microstructure, and a study of the effects of corrosion, with particular reference to the structural aspects of local and selective dezincification. Although the bibliography on the corrosion of brass pipes is quite extensive, it refers almost entirely to corrosion in sea water. The authors believe that their examination of this series of pipes, which had been subjected to the corrosive action of fresh water for various lengths of time, may throw some additional light on the problem of corrosion. Pipes Examined The pipes were made by different manufacturers and their sizes range from 3/4 in. to 4 in. nominal inside diameter, the majority being within I to 2 in. They can be divided into two groups according to chemical composition: (I) with a copper content of 60 to 62 per cent and (2) with a copper content of 65 to 68 per cent. The first group (pipes made of Muntz metal) comprises 22 pipes and the second (pipes made of high brass) comprises 18 pipes. The pipes had been in service in various locations in the hot-water systems of the buildings involved. Some were taken from horizontal lines in the basement, some from overhead distributors and some from vertical risers. The distance, in terms of feet of pipe, of the specimens from the hot-water generator was no less than 75 ft. and often IOO to 300 ft. In the majority of cases the water-heating equipment was provided with a regulator to limit the temperature of the hot water supply. The normal range of temperature in pipe systems of this kind is Ioo° to 160°F. Water Supples The average chemical composition of the water supplies carried by the pipes is shown in Table I. In evaluating the corrosiveness of a natural water, four factors are considered of prime importance: namely, hardness, alkalinity, pH and silica content. The waters listed in Table 1 are characterized by relatively low hardness, 10, alkalinity, low pH and low silica content. The waters of lower pH and higher CO2 content are more corrosive. A characteristic of all of these waters is that they do not deposit a protective mineral coating as do waters with high bicarbonate of lime content, which would be reflected

Jan 1, 1945

By Archer E., Wheeler

Producing copper companies were active during 1941 owing to the national defense program the United States and the requirements of the friendly belligerent nation. This activity extended to the American owned properties in South America, the major part of whose product was taken by the Metals Reserve Co., a U.S. Government agency. Anaconda Copper Mining Co. is building a new converter plant at Anaconda, with four units of the Peirce-Smith type. The addition is being built adjacent to the reverberatory plant so as to avoid the necessity of hauling matte and slag. It is expected to be completed this year.

Jan 1, 1942

By Robert T. Pring

IN addition to the humanitarian aspects of a dust-control program, certain economic benefits are becoming more fully recognized and now furnish a greater incentive to the mill operator to eliminate the dust from his plant. It is well known that a favorable working environment promotes increased efficiency and improves the morale of employees, with a consequent decrease in labor turnover rates. One progressive mining company1 estimates its direct and indirect labor turnover costs at from $40 to $50 per man; for skilled labor, such as machine operators, the cost may approach $100 per man. While these figures may not be typical of every plant, they do indicate a potential savings in operating costs. Dust signifies waste; its elimination decreases maintenance costs of mechanical and electrical equipment; its recovery is often justified from the standpoint of values contained in the collected material, although in large-scale milling operations handling low-grade ore this may not be an important factor. Perhaps the most significant trend in industrial sanitation is that dust-control equipment and procedures are becoming recognized as integral parts of the mill flowsheet. Exhaust ventilating systems are now afforded equal care in design and maintenance to that given other machinery more closely related to the process. METHODS OF DUST CONTROL "Dust control" is a general term descriptive of a number of methods used singly or together to prevent particulate atmospheric contamination. These methods are, in order of their desirability, as follows: I. Change of process. 2. Isolation of process. 3. Wet methods. 4. Ventilation. a. Local exhaust ventilation. b. General ventilation. 5. Personal respiratory protection. In ore-concentration plants it is seldom practical to change a process to eliminate the dust it creates It is possible in some cases to isolate a particular dust-producing operation from the rest of the plant, provided that constant attention on the part of the operators is not required. Frequently water is used in fine crushing and fine grinding, primarily to facilitate the processing of the ore and incidentally to allay the dust produced. Wet methods, however, are not feasible in coarse and secondary crushing operations, because of the relatively great volume of water required in instantly wetting each freshly fractured rock surface. Such quantities of water would entail conveying and storage difficulties. Local exhaust ventilation is the most effective and most commonly applied control measure, wherein directional air currents through the zone of dust production draw the contaminants into a duct system. Unfortunately, only a limited amount of reliable information on exhaust ventilation is available.2-5 Of necessity these publications are rather general, being primarily concerned with engineering fundamentals. While many organizations have successfully

Jan 1, 1940

By Casimir Constable

DURING the years 1875 to 1879 I had charge of the Rockwood furnaces and mines, situated forty miles from the nearest railway communication at that time, and one hundred miles north of Chap tanooga, Tenn., by the Tennessee River. The small furnace with old-fashioned stoves, then in blast, was built under great difficulties by General Wilder. The early conditions were somewhat as follows: The ore was fossil ore of the Clinton group ; very fine and generally wet, without other admixture. The coke had a large amount of ash, and the fur" nace appeared to be badly scaffolded at times. On many days only a few tons of iron could be obtained. The founder generally id creased the revolutions of the engine when signs of chilling appeared,. The cinder at such times was black, very scoriatious, often closely resembling mill cinder. When the pressure was increased (the joints being the old-fashioned rust joints), leaks in the blast-pipe occurred It was noted that when the blast was stopped, and the leak bolt imperfectly remedied, the furnace improved a little. This set me thinking on the right track; and I took the responsibility of be coming my own founder for a time. A scaffolded condition had existed, and the situation was a trying one. Strange to say the negroes proved excellent furnace-men. Conceiving the hearth of the furnace to be similar to the grate area of a steam-boiler, capable of disposing of but so much fuel per hour, and requiring only a corresponding amount of air, it follows that an excess of air will burn the fuel not yet arrived at the hearth!, and raise the melting-point far above the tuyeres. This might pro duce scaffolding or at any rate choke the boshes, and leave less fuel to be consumed in the hearth. Thus for the time being less ail;. would be needed, as the continued burning of fuel in and above the boshes, would only aggravate the trouble. This condition of affairs accounted for the black cinder; the heat above having melted ore not yet perfectly reduced. This view decided me to reduce the revolutions of the engine; thefurnace finally became gray, as might have been expected. Any attempt to increase the speed produced black cinder and hard iron ;

Jan 1, 1883

By G. E. Johnson

LEAD SMELTERS AND REFINERS in 1932 were confronted with the problem of adjusting operations and costs to curtailed production and consumption at reduced prices, a problem which has been partially solved at least by improvements in operating technique and increased efficiency. At the Mount Isa properties in Australia, a third blast furnace and additional Dwight-Lloyd sintering machines were installed during the year, designed to increase the production to 6,000 tons of bullion per month. The large proportion of lead carbonate in the ores to be treated has presented metallurgical problems. Of the total lead contained in the concentrates to be smelted, two-thirds is Dresent as carbonates and one-third as sulfides. In the iiitial operations, the resulting Dwight-Lloyd sinter was soft, contained an excessive amount of fines, and was easily fusible. When charged to the blast furnaces it developed accretions in the upper part of the furnace owing to the easily fusible lead carbonates softening and fusing at the top of the charge column. This was remedied by the addition to the sinter feed of diluents of higher melting point, granulated slag and crushed limestone. The sinter feed consists of concentrates, Cottrell dust and wind-box cleanings, totalling 57 per cent of the charge; return sinter fines 15 per cent; granulated slag 23 per cent; and crushed limestone 5 per cent. The sinter produced contains 34 per cent lead and 0.5 per cent sulfur. Experiments indicated that double sintering under these conditions was of no advantage, so the original plan of single sinter treatment was retained.

Jan 1, 1933

By AIME AIME

M ODERN metallurgy properly belongs to this century. The great advance made in this science is directly attributable to the discovery of the Roentgen rays. Application of the results of this discovery, together with the more recent corroborating studies in electronic diffraction have definitely and for all time established this science. Metallurgists today speak with familiarity of the atoms of the different metals in terms of their orientation, atomic volumes, lattice structures, dimensional lattice constants distance of nearest approach, and the like. One matter of profound interest, which is quite staggering to the imagination of the human mind, is the enormity of the number of atoms even in a small particle of metal. As an illustration, let us compute the number of atoms in the volume of one cubic centimeter in a single grain of absolutely pure copper. Eighteen and a fraction cubic centimeters equal the volume of one cubic inch.

Jan 1, 1940

PRESIDENT OF THE COUNCIL. D. W. BRUNTON DENVER, COLO. (Term expires February, 1910 ) VICE-PRESIDENTS OF THE COUNCIL. J. PARKE CHANNING NEW YORK, N. Y. FREDERICK W. DENTON PAINESDALE, MICH. JOHN B. FARISH NEW YORK, N. Y. (Term expires February, 1910 ) W. C. RALSTON SAN FRANCISCO, CAL. W. L. SAUNDERS NEW YORK, N. Y. H. V. WINCHELL MINNEAPOLIS, MINK. (Term expires February, 1911 )

Jan 1, 1910

PRESIDENT OF THE COUNCIL. D. W. BRUNTON DENVER, COLO. (Term expires February, 1911.) VICE-PRESIDENTS OF THE COUNCIL. W. C. RALSTON SAN FRANCISCO, CAL. W. L. SAUNDERS NEW YORK, N. Y. H. V. WINCHELL ST. PAUL, MINN.¬ (Term expires February, 1911.) BENJAMIN B. LAWRENCE NEW YORK, N. Y. JOSEPH W. RICHARDS SOUTH BETHLEHEM, PA. ALBERT SAUVEUR CAMBRIDGE, MASS. (Term expires February, 1912.)

Jan 1, 1917