Search Documents

By Paul F. Kerr

The uranium-producing areas near Marysvale, Utah provide an unusual group of veins and replacement deposits associated with a Pliocene-Oligocene intrusive and extrusive igneous complex. Aside from several scattered occurrences in older volcanics, uranium-bearing veins occur in intrusive quartz monzonite or granite and in nearby rhyolite. The veins in general trend within a few degrees of N55-65°E, are more or less vertical, and are found along the western margins of a quartz monzonite intrusive. The replacement deposits are found in rhyolite intrusives and also in the lower portions of rhyolite flows close to places where veins forming solutions rising through quartz monzonite came into contact with the rhyolite. At least 14 veins have been mined since uranium mining operations began at Marysvale some 16 years ago, while ore has been extracted through about 10 miles of underground workings. The active mmmg area is approximately 3000 feet long and in the central portion 1500 feet wide. Ores have been found over a vertical spread of almost 2000 feet, between the highest occurrence on Jungfrau Hill ( ca. 7200 feet) and the deepest discovery of ore in a drill hole near the Prospector Mine (ca. 5200 feet). Under existing mining and marketing conditions, mining along the veins in the main area appears to have reached an economic limit at about 500-600 feet below the surface. However, orebodies in the rhyolite and in the upper portions of veins close to the rhyolite are subject to active mining. Isotopic dates indicate that the uraninitebearing veins and replacements are late Miocene or Pliocene (ca. 10-13 m.y.), the rhyolite is Miocene (avg. 17.5 m.y.), and the quartz monzonite and granite intrusives are late Oligocene (23.6 to 26.0 m.y.). The older Bullion Canyon Volcanic Series which encircles the area is Oligocene (28 to 31.1 m.y.). Two generations of alteration occur: ( 1) Earlier alunitic veins and replacement bodies are found in the Bullion Canyon Volcanic Series, none of which have produced uranium; (2) Later argillic alteration associated with the introduction of uranium is found along veins, replacing glassy rhyolite dikes and replacing phases of the rhyolite.

Jan 1, 1968

By H. E. Kramm

(New York Meeting, February, 1919.) DURING the summer of 1911, I had the opportunity to study in detail the geological conditions of what is known in northern California as " Harrison gulch," in Shasta county. Though the district, as a whole, that is, the western part of Shasta and the eastern part of Trinity county, has contributed during the last 15 years a considerable share of the gold-production credited to Shasta county, very little is known of its geology, perhaps because the country is covered with a dense growth of brush which makes exploration and prospecting extremely difficult. Topographically the district presents a succession of ridges trending approximately N-S.; and alternating with deep narrow canyons. The drainage is partly into . the Sacramento, partly into the Trinity river. Climatic conditions in summer time are almost ideal. It is true, the thermometer may climb to 115°, but the air is dry and the heat is bearable, especially as the nights are always cool. It seldom rains during the summer months, and creeks and springs dry out towards the end of the summer. The winter is severe, lasting from November to April, and usually a thick layer of snow covers the mountains. By reason of the character of its gold-deposits, the region is known to miners as "the pocket country." It contains a series ?of eruptive rocks intruded into slates, cherts, limestones, and conglomerates. Dikes, laccoliths, and batholiths are frequent. In a day's ride it is possible to find all the common igneous rocks from the very acid to the very basic. Serpentines are especially abundant.. The sedimentary rocks are, as rule, broken and shattered as well as folded, and show the effects of intense metamorphism. ? Pocket-hunters " speak of the contact of diabase and slate as the ? pocket-contact." Some rich gold-pockets, however, have also been found in the diabase.

Jul 1, 1912

By Strathmore R. B. Cooke, Robert E. Brandt

EARLIER work1,2 has shown that the strength developed by fired magnetite pellets containing silica or silicates is due to three separate effects. Two of these are associated with the formation of slag in the interior of each pellet at temperatures above 1000°C, where the atmosphere is substantially though temporarily neutral. The third is independent of the silica content and is responsible for the development of a hard shell around the pellet during the initial stages of firing, a condition which permits the pellet to assume the increasing load of the overlying burden and prevents extrusion of the slagged and semi-liquid interior. Pellets made from hematite concentrates do not show these effects unless specific additives are incorporated, and it is these differences in behavior which in large part account for the difficulty in producing satisfactory pellets from such concentrates. Elsewhere it has been stated that "the most important factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of magnetite to hematite and the subsequent recrystallization and grain growth of this constituent."1 The object of the investigation reported in the present paper was to study in detail the mechanism described above and to evaluate its contribution to the strength of the fired pellet compared with other possible mechanisms, excluding slag bonding. This was effected by placing together polished faces of two cubes prepared from specific minerals and then heating them under constant pressure at different temperatures both in air and in nitrogen.

Jan 4, 1954

By M. B. Kahle, A. D. Pernichele

Four types of slope failures in waste dumps are recognized debris flow, foundation failure, edge slump, and blowout. The first three types, although at times causing considerable damage to property and interfering with mine operations, are not usually dangerous to personnel because of their slow rate of movement. The fourth type, the blowout, is the most dangerous because of its explosive mode of failure and lack of forewarning. The December 1969 failure at Verona dump is presented as an example of a blowout. Data from piezometer holes indicate that the blowout was due to perched leach solutions near the face of the dump. The level of water in this zone is very closely related to the rate of leach water application on the dump. A detailed analysis of core samples indicates that the impounded water was perched on a zonal accumulation of jarosite which is associated with a buried dump surface. Drain holes proved successful in controlling perched leach solutions in the critical zone near the face of the dump. Monitoring of the water level in the perched zone is considered essential in preventing blowouts. The use of drain and piezometer holes has allowed an increase in the rate of water application on the dump while preventing additional failure.

Jan 1, 1972

By Eugene Guccione

FOREWORD-In an interview published in the May 1975 issue of MINING ENGINEERING, one of the world's most respected scientists, nuclear physicist Hans Bethe discussed the reliability of nuclear power plants and their unmatched safety record. The Nobel laureate also refuted the anti-nuclear lobby's claims that nuclear plants emit harmful radioactive effluents. When asked whether the US has sufficient uranium resources, Dr. Bethe replied that "it depends on the time of introduction of the commercial and advanced breeder reactors which, in effect, can generate more nuclear fuel than they consume." The United States has enough U3O8 to last until the breeders can take over in 1995, said Dr. Bethe. But lie warned that extensive environmental damage would be caused if "environmentalists" succeed in delaying the development of the breeder. Any such delays, he noted, would vastly increase the demand for U3O8 in conventional reactors; this, in turn, would impose an immense burden on the US uranium mining industry, which would then have no alternative but to mine the low-grade Chattanooga deposits.

Jan 4, 1977

By M. D. Banus, M. B. Bever, A. K. Jena

Measurements of the heat effects on addition of various solid phases of InSb to a solution calorimeter have confirmed the existence of a new high-pressure plzase InSbQII), which was jormed at 37 kbar and 623°K. The heats of formation of InSbQ), InSbfl), and InSb(111) have been measured and the heats of transjormation of InSb(1) to InSb(1l) and InSb(Iii) and of 'InSb(ll) to InSb(iiI) at atmospheric pressure and 78°K have been determined independently. Other thermodynamic properties of these phases, the phase boundary InSb(i)/InSb(ll), and the relative positions of the triple points are calculated. The pressure-Dolume term is shown to be more critical than the internal energy difference in making the phase InSbQ) less stable than InSb(II) at high pressures. Observations on partially transformed specimens suggest that the transformation of' metastable InSb (III) takes place in the two steps InSb(lll) — InSbQI) and InSbQI) — InSb(l). The compound InSb can exist as several phases depending on the temperature and pressure. The phase InSb(I), which is a semiconductor having the zinc-blende structure, transforms into the phase InSb(11) at a pressure of about 23 kbar and room temperature.'-3 The phase InSb(II) has the 6 tin structure,4-6 is metallic, and becomes a superconductor below 2.lok7 An orthorhombic phase of InSb has been reported to occur above a pressure of approximately 30 kbar at room temperature.' This phase is also a superconductor below about 3.4k9 The phase InSb(I1) is retained at atmospheric pressure if it is quenched to 78°K under pressure,6,7 but tends to transform at higher temperatures and does so explosively above approximately 210ok,7 A value of the heat of transformation of InSb(1) to InSb(II) at 210°K and atmospheric pressure has been reported.' A concurrent publication'0 reports evidence for a new solid phase InSb(III), which was formed by annealing InSb above 58 1°K at 37 kbar, above 560°K at 52 kbar, and above 473°K at 65 kbar. Specimens of InSb(II1) had a superconducting transition temperature of 4.lo ± 0.1oK. X-ray diffraction patterns also indicated the presence of a new phase. In this communication, thermodynamic properties of the phases InSb(I), InSb(II), and InSb(II1) are reported and discussed. The phase boundary InSb(I)/InSb(II) and the relative positions of the triple points are calculated. 1) EXPERIMENTAL 1.1) Preparation of Specimens. Specimens of the high-pressure phases of InSb were prepared in a belt-type high-pressure chamber by a tichnique described in detail elsewhere.'' Charges of 0.6 to 0.8 g of Cominco semiconductor grade InSb were used. The temperatures were measured with a chromel-alumel thermocouple, the hot junction of which was within 0.5 mm of the specimen. The specimens were heated under a pressure of 37 kbar for 1 hr at 723°K (which is well above the liquidus) and quenched to room temperature. One set was annealed at 523°K and another set at 623°K for 20 to 24 hr. These annealing temperatures were chosen because 523°K was below and 623°K was above the temperature of the transformation of InSb(II) to InSb(1Tl) at 37 kbar.10 The specimens were then cooled to 125°K by passing liquid nitrogen through the jacket of the belt die before the

Jan 1, 1968

By P. J. Root, J. E. Warren

An idealized model has been developed for the purpose of studying the characteristic behavior of a permeable medium which contains regions which contribute significantly to the pore volume of the system but contribute negligibly to the flow capacity; e.g., a naturally fractured or vugular reservoir. Unsteady-state flow in this model reservoir has been investigated analytically. The pressure build-up performance has been examined in some detail; and, a technique for analyzing the build-up data to evaluate the desired parameters has been suggested. The use of this approach in the interpretation of field data has been discussed. As a result of this study, the following general conclusions can be drawn: 1. Two parameters are sufficient to characterize the deviation of the behavior of a medium with "double porositym from that of a homogeneously porous medium. 2. These parameters can be evaluated by the proper analysis of pressure build-up data obtained from adequately designed tests. 3. Since the build-up curve associated with this type of porous system is similar to that obtained from a stratified reservoir, an unambiguous interpretation is not possible without additional information. 4. Differencing methods which utilize pressure data from the final stages of a build-up test should be used with extreme caution. INTRODUCTION In order to plan a sound exploitation program or a successful secondary-recovery project, sufficient reliable information concerning the nature of the reservoir-fluid system must be available. Since it is evident that an adequate description of the reservoir rock is necessary if this condition is to be fulfilled, the present investigation was undertaken for the purpose of improving the fluid-flow characterization, based on normally available data, of a particular porous medium. DISCUSSION OF THE PROBLEM For many years it was widely assumed that, for the purpose of making engineering studies, two param- eters were sufficient to describe the single-phase flow properties of a producing formation, i.e., the absolute permeability and the effective porosity. It later became evident that the concept of directional permeability was of more than academic interest; consequently, the degree of permeability anisotropy and the orientation of the principal axes of permeability were accepted as basic parameters governing reservoir performance. 1,2 More recently, 3-6 it was recognized that at least one additional parameter was required to depict the behavior of a porous system containing regions which contributed significantly to the pore volume but contributed negligibly to the flow capacity. Microscopically, these regions could be "dead-end" or "storage" pores or, macroscopi-cally, they could be discrete volumes of low-permeability matrix rock combined with natural fissures in a reservoir. It is obvious that some provision for the inclusion of all the indicated parameters, as well as their spatial variations, must be made if a truly useful, conceptual model of a reservoir is to be developed. A dichotomy of the internal voids of reservoir rocks has been suggested.7,8 These two classes of porosity can be described as follows: a. Primary porosity is intergranular and controlled by deposition and lithification. It is highly interconnected and usually can be correlated with permeability since it is largely dependent on the geometry, size distribution and spatial distribution of the grains. The void systems of sands, sandstones and oolitic limestones are typical of this type. b. Secondary porosity is foramenular and is controlled by fracturing, jointing and/or solution in circulating water although it may be modified by infilling as a result of precipitation. It is not highly interconnected and usually cannot be correlated with permeability. Solution channels or vugular voids developed during weathering or burial in sedimentary basins are indigenous to carbonate rocks such as limestones or dolomites. Joints or fissures which occur in massive, extensive formations composed of shale, siltstone, schist, limestone or dolomite are generally vertical, and they are ascribed to tensional failure during mechanical deformation (the permeability associated with this type of void system is often anisotropic). Shrinkage cracks are the result

We are advised by Carrington Phelps, Secretary of the professional Classes War Relief of America, having offices at 33 West 42d Street, New York, that this organization is now prepared for active relief of professional men who have enlisted in military service or are assisting the Government in the civil service or in civil life, at the sacrifice of their usual sources of income. The organization has found that the main obstacle to such relief is the hesitancy of this class of persons to make known their needs. Relief cases have to be sought out; the organization has already found some but has asked the cooperation of the Institute to assist in finding as many more as may exist. It is suggested that the Institute can render useful service in this connection, first, by informing our members of this feature of war relief, by being on the alert to report those needing relief, and to make all possible inquiry after such cases. It is further desired that information as to all such cases be forwarded immediately upon their discovery.

Jan 3, 1918

By W. E. D. Jr. Stokes

THE application of aviation to mining and petroleum operations, on the basis of economy and attainment, has become a demonstrated fact. According to Dominion Government records, 30. Canadian companies engaged in air transportation with northland mining camps, carried 13,000 tons of freight in 1935, and in 1936 carried 16,000 tons. In addition, many mining companies used planes to transport prospectors with canoes, outboard motors, gasoline drums and supplies to remote locations, and one company maintained a plane to take radium-bearing ore from its mine on Great Bear Lake nearly 1000 miles south to the rail-way at Waterways, Alberta. Heavy pieces of mining machinery weighing 2 tons are being carried by Ford trimotor planes over the Andes, at an altitude of not less than 15,000 feet. At Bulolo, New Guinea, 17,500 tons of disassembled gold-dredging equipment has been flown over inaccessible terrain, while supplies and building materials for a, community of 1000 whites have been transported by airplane. A 31..4-ton shaft was carried on one notable trip, while at another time an automobile, 2 tons of rice and a large safe went over the mountains in one plane. Fig. 1 shows an electric generator that was carried by plane to Bulolo. Many large American oil companies operated fleets of planes during 19:36, ranging from fast, luxurious air liners for executives to elaborate geological prospecting units, ambulance planes, freight carriers and pipe-line repair crews. According to the U. S. Geological Survey, commercial firms photo-graphed 16,291 square miles during 1935, while the Government compiled from aerial photographs by the Geological Survey in the United States 85,544 square miles. It was found that information could be determined in a fraction of the time required by surface methods.

Jan 1, 1937

By B. A. Rogers

The etching effect that is produced on a piece of polished iron or steel when it is heated in hydrogen or in a vacuum seems to have been observed first by Osmond,' who believed that he could distinguish four systems of grain boundaries on a piece of steel which had been heated in hydrogen. In a number of other investigations, samples of pure iron were found, after heating, to have complex networks in which two or three systems of grain boundaries could be detected. It was further noticed that samples that had been polished plane before being placed in the furnace were, after treatment, roughened and undulating over their entire surfaces. From a comparison of the temperature of heat treatment with that of the A3 transformation, it was concluded that the changed appearance of the samples was definitely related to the latter phenomenon. Certain other deductions were made but these are not of importance here and only observations on the appearance of the samples will be reviewed. Ewen2 heated a strip of polished iron in a vacuum in such a way that one end was maintained at a temperature of 1000" C. and the other at 580" C. On the cooler end there was outlined a simple polyhedral network, and at the hotter there appeared the complex systern of lines ant the undulating surface characteristic of iron which has passed through the A3 transformation. He found that in going from the cooler toward thc hotter end the sample maintained much the same character of surface up to the beginning of the transformed area, but that near this region doublc grain boundaries were of frequent occurrence. Rawdon and Scott concluded that the simple type of network brought out by heating a sample of pure iron in a vacuum was of the same type as that developec by ordinary etching methods. They also confirmed the observations of

Jan 1, 1929

By Richard W. Greene, Joel S. Hirschhorn

MATERIALS containing very large amounts of porosity, in the order of 50 to 90 vol pct, are extremely difficult to evaluate according to conventional mechanical behavior tests. This is usually a consequence of their low strength and brittleness, and the difficulty of preparing standard test specimens. A simple fatigue test has been developed and used successfully on porous nickel sheet materials requiring no specimen preparation; it could also be used for configurations other than sheet or plate. Samples of the sheet. 2 in. sq and about 0.025 in. thick, are placed in a vessel that is evacuated to about 50 f Hg by a mechanical pump. Distilled and deairated water is allowed to enter the vessel thereby filling the porosity (virtually all the porosity in these nickel ma-

Jan 1, 1970

By C. E. Violet, R. J. Borg, E. M. Howard

The miscibility gap in the Au-Ni system has been determined by Mossbauer spectroscopy, with used as a probe. The phase boundaries were determined from the compositional dependence of both the isomer shift and Curie temperature. X-ray diffraction measurements were also used to confirm the Mossbauer results. 1 HE purpose of this research is to demonstrate the application of Mbssbauer spectroscopy to the determination of phase boundaries and to redetermine the miscibility gap by an independent and novel technique. The techniques evolved in this study are readily applicable to other polyphase systems and are generally as quick and accurate as the more conventional methods, e.g., metallography, X-ray diffraction, thermal analysis, and so forth. To be sure, not all polyphase systems will lend themselves favorably to Mijssbauer investigations, but this is a problem met in the use of conventional methods as well. The Mbssbauer spectrum responds to a different set of physical parameters, and consequently provides an entirely independent method of analysis. It is especially useful if the system has either a ferromagnetic or an antiferromagnetic transition. The Au-Ni system was selected because alloys containing more than -60 at. pct Ni become magnetically ordered at low temperatures; also the miscibility gap is quite well established (see Ref. 7 for a compilation of pertinent references, also Fig. 11, and thus provides a reliable test of this novel procedure. As Fe is the most commonly used Mijssbauer isotope, there exists a wealth of information concerning its behavior in iron-containing alloys and compounds. However, as yet there have been relatively few experiments using it as a probe to investigate nonferrous systems. By choosing a nonferrous alloy system, we are able to demonstrate that its use is not restricted to systems containing iron as one of the major constituents. Wertheim and ~ernick' have used the same method to investigate Cu-Ni, and demonstrated that one can obtain a systematic variation in the isomer shift and magnetic hyperfine field. However, we believe this to be the first time these techniques have been used to establish phase boundaries. Two hyperfine interactions were measured and used to determine the phase boundaries, viz., the magnetic hyperfine splitting and the isomer shift which in this alloy system are both strong functions of composition. Calibration curves were established based upon single-phase solid solutions obtained by quenching from temperatures well above the maximum of the miscibility gap, see Fig. 1. Solid solutions containing 25, 50, 65, 75, 85, 92, and 96 pct Ni as well as pure nickel were used in the calibration procedure. Fig. 2 shows the Curie temperature, TC, and the isomer shift, v,, as determined from the Mbssbauer spectra, and variation in lattice parameter as determined by X-ray diffraction, as functions of composition. The compositions of the two-phase systems quenched from temperatures within the miscibility gap are obtained by comparing their respective values of TC and v0 with the calibration data. I) EXPERIMENTAL Mbssbauer sources were made by fusing the component metals in a tungsten arc melter, which has a water-cooled copper hearth. Both nickel and gold were 99.999 pct pure, and the melting was done in an atmosphere of purified argon. The alloys were rolled, diced,

Jan 1, 1969

Aamot, Olav Crone, Chem. Engr., Norsk Elektrokemisk, Kongensgt. 18, Olso. Norway. '29 Abadilla.-Quirico A., Dir., Bureau of Mines Manila, P. I. '38 Abbott, Clarence E., V.P., Charge of Raw Materials, Tennessee Coal, Iron & R.R. Co., 1212 Brown-Marx Bldg., Birmingham, Ala. '04 Abel, Raymond L., Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh, Pa. '29 Abel. Walter D., Cons. Engr 1839 Holmby Ave., W. Los Angeles. Calif. '32 Abele, Louis T R. F. D. 5. Susquehanna Trail, N., York. Pa. '31 Abell, Leo M., Ore Dressing Investigator, School of Mines Adelaide, S. Australia. '31 Abenius. Hakan V., Mine Supt., Bolidens Gruvaktiebolag Boliden, Sweden. '37 Aborn, Robert H., Asst Met., Research Lab., U. S. Steel Corp. Lincoln Highway, Kearny, N. J. '19 Abraham, W. E. V., East India United Service-Club, 16 St. James' Sq., London, S. W. 1, England. '28 Abrams. Charles Jackson 1624 17th St., Denver, Colo. '36 Abstein, Henry T., Engr. & Mgr., Profile-Tamarack Mines Co Yellow Pine, Idaho. '27

Jan 1, 1938

By J. N. Butler, R. J. Morris

A series of organic collectors has been developed which successfully float synthetic secondary uranium minerals, such as autunite, carnotite, and torbernite. Recoveries up to 97 pct have been obtained. With cleaning of rougher concentrates, ratios of concentration as high as 15:1 are possible on head assays of 0.10 to 0.50 pct U 3 O 8. Additions of certain base metal salts aid in recovery and materially increase the rate of flotation and selectivity of the collectors for the synthetic minerals. Flotation tests on natural uranium minerals have not yet equaled results obtained on the synthetics, although these collectors do give better results than conventional collectors for nonsulfide minerals. RAPID increase in mining and milling uranium ores during the past seven years and the discovery of large tonnages of uranium-bearing material too low in grade to stand the cost of leaching have developed considerable interest in possible methods for beneficiating these marginal ores. Such ores are generally classed as those containing less than 0.10 pct U3O8. Development of a beneficiation method that would give both high recovery and high ratio of concentration would also make possible the beneficiation of higher grade ores and would provide higher grades of feed to existing leaching plants. Although considerable research and testing on physical or physico-chemical beneficiation of domestic uranium ores has been done in the past, to the best knowledge of the authors only a single application of physical beneficiation is now in operation on a commercial scale. Flotation has been attempted on the basis of mineral association rather than by direct concentration of the contained uranium minerals. Flotation studies conducted on this project on certain ores gave recoveries of 60 to 70 pct of the uranium by the use of conventional flotation agents such as oleic acid, but ratios of concentration were in the order of 1.5:1 to 2.5:1. Subsequent cleaning to upgrade the concentrates rapidly increased losses in the cleaner tailings, which were not later refloated in the rougher flotation. Selection of Collector: In selecting desirable organic collectors for these oxide systems, a thorough study was made of the relationship between structural characteristics and collector activity by an examination of the behavior of a number of different functional arrangements present in a variety of organic molecules, (see Fig. 1). It is generally accepted that a collector must have a relatively long-chain hydrocarbon radical and a chemically reactive elec-trophilic center. Such a requirement could be met by a large number of compounds, but steric effects at the uranium mineral surface, solubility, compat-ability with aqueous systems, air avidity, bond strength at the mineral surface, interfacial concentration of the collector, and diffusion rate of the formed complex from the air-water interface eliminated many as unsuitable for this purpose. Preliminary investigations were completed of possible collector designs consisting of aliphatic and aromatic hydrocarbon radicals attached to stable combinations of nitrogen, oxygen, sulfur, and halogen electrophilic centers, Fig. 1.Tests were made to determine melting point spans, solubility of mineral-collector combinations in various solvents, reactions with soluble uranium salts, contact angles, and floatability by semi-quantitative beaker methods.' Contact angle determinations were not too useful because of the fine particle sizes of available mineral samples. From the foregoing study it appeared that nitrogen-sulfur electrophilic centers coupled with straight-chain saturated alkyl hydrocarbon radicals would hold the most promise for floating secondary uranium minerals. As the dithiocarbamate compounds can be made to combine these attributes they were selected for further study. The dithiocarbamates form a parallel structure to the xanthates, with the fortuitous exchange of

Jan 1, 1957

By AIME AIME

MINING geology has been at once the vocation and avocation of John M. Boutwell, newly elected Director of the Institute representing Utah and Colorado. Geologists were looked at askance by most of the "big" men in mining when, from 1896 to 1900. Mr. Boutwell was teaching geology at Harvard, his alma neater; and his success in applying geologic principles to the business of finding ore contributed much to changing the attitude of scepticism. From 1900 to 1908 lie was with the U. S. Geological Survey, with service in Bingham, Utah; Morenci, Ariz.; and Park City, Utah. Since then he has been engaged in private practice as a consulting mining geologist retained by many of the leading mining companies. A dozen men now recognized as outstanding geologists got their early

Jan 1, 1937

By H. R. MacMichael

IN the Chihuahua district of Mexico the first smelting was that inaugurated by the early Spaniards for the production of silver bullion. The ores treated were high in silver and lead. Silver-lead bullion was first produced and the lead then cupelled to waste, with the slag produced running from 5 to 10 per cent in lead and about 25 to 40 per cent silica. The ore was mined by peon labor, often being carried out of the mine on the backs of the men, and then transported by burros. Furnaces were of primitive construction, adobe or rock being used in the earlier period and some iron later when it became available. Blast was originally supplied by bellows manually operated. Such smelting was carried on to a greater or lesser extent until the latter part of the last century, and so extensive was it that many hundred thousand tons of leady slag remained to be treated in modern furnaces. In 1908 a smelter was placed in operation at Chihuahua by the American Smelting & Refining Co. At that time the ore was practically all oxidized and by a little selection, self-fluxing mixtures could be made, but with an average lead content usually under 10 per cent and sometimes as low as 7 per cent. The bullion produced would carry from 150 to 300 oz. silver per ton. The slag made approximated 30 per cent SiO2, 42 per cent FeO, 21 per cent CaO, and perhaps 3 per cent Zn. The ores varied from hard, coarse material which was passed through a crusher, to a considerable quantity of fines which had to be smelted as it came, as crushing the coarse was the only preparation for smelting.

Jan 1, 1933

By N. Plint, E. T. Pinkney

Copper segregation developments within the Anglo American Group are described with particular reference to the work of the TORCO Project Team. Some radical differences have been adopted in the mechan-ical approach as compared with methods used by previous workers. Most important among these are the following: (1) The heating unit is a fluidized-bed roaster. (2) A moving bed segregation chamber is used in which a packed bed of heated ore, to which reagents have been added, moves slowly downwards under gravity and is discharged at a controlled rate by means of a suitable valve mechanism. (3) The quantities of reagents used (sodium chloride and some form of carbon) are only a small fraction of those recommended by other investigators. (4) Retention times of only 2 min have been satisfactory for the complete segregation of many types of ore. Project TORCO is the code name given by Anglo American Corp. of South Africa, Ltd., to the investigation undertaken in Zambia to develop a plant capable of treating large tonnages of refractory copper-bearing ores by the segregation process. The process has now been under investigation for six years (1960-66) and during that period work has progressed from bench-scale laboratory tests through small-scale pilot-plant work to a 500-tpd commercial pilot unit. Test work has been carried out mainly on the ores of the Zambian Copperbelt and results have been encouraging. Recoveries on the order of 90% have been obtained on all Copperbelt ores tested with high concentrate grades. PRELIMINARY INVESTIGATION Laboratory scale segregation test work on Nchanga banded sandstone ore and oxidized ore from Kansan-shi was originally conducted by Professor Maurice Rey. SociCtC Miniere et Mktallurgique de Pefiarroya, in 1957. Both ores responded favorably to the process. In November, 1960, the consulting engineers of Anglo American Corp. of South Africa, Ltd., initiated preliminary investigations on the application of the segregation process to Copperbelt ores. In early laboratory work, samples were heated in a closed, externally heated tube furnace for one hour at temperatures ranging from 800 to 830°C. The free moisture content of the ore feed was 4% and reagent additions were 0.5% salt and 1.0% coal. Both salt and coal were pre-crushed to -48 mesh Tyler.* All samples except an ore from the Bancroft mine responded well to the process and recoveries of over 90% were obtained. The presence of dolomite was responsible for the relatively poor recoveries from the Bancroft ore, as tests on one of the other ores with additions of calcite or dolomite confirmed. Recoveries dropped from 94 to 45% Grades of all the rougher flotation concentrates produced were low at 10-15% copper. The laboratory investigation was then followed up on a pilot-plant scale. An attempt was made to carry out the segregation process in a coal-fired 5-ft-diam fluidized-bed roaster. The feed consisted of a banded sandstone from Nchanga to which 0.5% sodium chloride had been added. Reducing conditions were maintained in the roaster by the addition of coal in excess of that required for heating the feed. The excess coal and added salt constituted the segregation reagents and the temperature of the bed was held at approximately 750°C. Recoveries of copper and grades of concentrates were low. The reasons for lack of success were: (1) The reaction is a gaseous one and a fluidized-bed roaster is therefore unsuitable as a segregation unit. (2) Coal in excess of that required for heating was introduced into the fluidized bed and under these conditions some of the copper would be reduced in situ. The term "reduced in situ" is used here to describe any copper mineral reduced to the metallic state in its original site within the ore particles. If this copper is to be recovered by subsequent froth flotation it must first be liberated from the gangue by grinding or some other method which, in practice, is usually not feasible on ores of this type.

Jan 1, 1969

In many lines of engineering, much excellent standardization work had been done before the war but the war emphasized its importance and showed most clearly the need of cooperation to prevent the confusion caused by the promulgation of overlapping standards by independent bodies. The American Institute of Mining and Metallurgical Engineers, American Institute of Electrical Engineers, American Society of Civil Engineers, American Society of Mechanical Engineers, and American Society for Testing Materials, recognizing the value of what had been done, invited the Government Departments of War, Navy and Commerce to appoint representatives to act with them to continue this work; the body so formed is the American Engineering Standards Committee. It has required time to definitely formulate its objects and to arrange methods for accomplishing them that would be effective without interfering with the many organizations that have been doing such excellent work in this line. The American Engineering Standards Committee has just completed and adopted a revision of its Constitution, which has been sent to the Governing Boards of all the Departments and Societies represented on the Committee with a request for its ratification. The new Constitution changes the name to American Engineering Standards Association as more fittingly indicating the wide scope of the interests involved. The objects of the association are stated as follows: 1. To unify and simplify the methods. of arriving at engineering standards, to secure cooperation between various organizations and to prevent duplication of standardization work. 2. To promulgate rules for the development and adoption of standards, 3. To receive and pass upon recommendations for standards submitted as provided in the Rules of Procedure, but not to initiate, define, or develop the details of any particular standard. 4. To act as a means of intercommunication between organizations and individuals interested in the problems of standardization. 5. To give an international status to approved American engineering standards. 6. To cooperate with similar organizations in other countries and to promote international standardization.

Jan 7, 1919

.MAX ROESLER, Firmeza, Oriente, Cuba (communication to the Secretary?).-It is substantially admitted by all who have recently been in touch with these deposits that the orebodies lie in the fine-grained dark-green rocks, called diorite by most writers and diabasic by myself. The three points of disagreement concern the agency of included limestone blocks as causes of deposition, the agency of the

Jan 5, 1917

Howard N. Eavenson, Gary, W. Va. (communication to the Secretary*):—For some time before the publication of Mr. Scholz's paper, I had been collecting data bearing upon its subject, and I now take pleasure in presenting to the Institute my results in the form of a discussion. It has long been a matter of common opinion among mining-men that mine-explosions are more frequent during the colder, or winter months, than during the warmer ones, and it is a matter of common knowledge among them that the air-ways and road-ways in most mines are much drier and are more inclined to be dusty during the winter than during the summer. In many mines, places which are wet and sloppy in the summer are dry and sometimes dusty during the winter. These changes, of course, can only be due to atmospheric conditions, and are caused by differences in temperature and humidity. Until recently, however, very little attention has been paid to the part that atmospheric conditions may play in mine-explosions, or, rather, to the effect they may have in rendering mine-conditions peculiarly dangerous, and in spreading and rendering more disastrous the effects of what otherwise probably would have been small explosions. To show the difference in mine-conditions during summer and winter months, I have tabulated in Table I. the results of 24 observations of hygrometric conditions in several different mines at different times of the year. Mines Nos. 1, 2, and 6 are located in the Pocahontas coal-region, in McDowell county,w.Va., the first one being a shaft-mine and the others drift. Mines 1A and 2A are drift-mines located in Logan county, W. Va. All of these are mines of fair size, but none of them has been in operation more than six years,

Jan 1, 1910