Search Documents

By Gust Bitsianes, Joseph H. M. Beaty

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By Joseph H. M. Beaty, Gust Bitsianes

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By C. A. Heiland

The following summary is written for the benefit of the practical operator in the nonmetallic field who wishes to know what geophysics has done and may be expected to do in his line of work. His problem is quite different from that of the geophysicist who has operated with various or all methods and has followed the literature, and who is assumed to be familiar with the geologic possibilities and limitations of each method. This article is not written for the latter, although he may be interested in the four or five hitherto unpublished surveys described. To the operator, on the other hand, geophysics is only secondary. His problem is to determine which geophysical method is best suited to his special needs. If he wanted to know, however, which method could be used to locate a certain material of given physical properties, building stone, for instance, he would have to wade through a tremendous amount of geophysical literature, bibliographies and articles, before he could find what he wanted. Therefore, the purpose of this summary is to present the geological problems first and then to discuss the comparative merits of the geophysical methods that can be, or have been, applied. Choice of Geophysical Methods in Oil, Civil and Mining Engineering In the first two of these fields, the geological problems are not nearly so complex as in the metal and nonmetallic mining fields. The selection of the correct geophysical method in these fields is not nearly so difficult for the operator. For oil prospecting, his problems have been discussed exhaustively by E. DeGolyer.(1) † In civil engineering (foundation and ground-water work), the usefulness of electrical methods has been so well established that there is hardly any choice of other methods at present. The situation may be changed in the future with the perfection of the seismic reflection method for shallow depths. In the mining field the operator and often the geophysicist himself finds difficulty in determining which method is best suited for a given

Jan 1, 1934

By Bruce A. Kennedy

The 1960's were an apparent turning point in the technological and social attitudes and awareness of the mining industry. From the late 19th century through to the early 20th century, one has always been presented with the picture of the rough and ready leaders of the mining industry who screamed for production and damned anything that got in the way of it. This attitude led to a certain alienation of the mining industry in the eyes of the general public. They saw an industry which was archaic in many of its practices and often heartless in its attitudes towards mankind. However, a gradual change spread through the industry and cracks began to appear in the hard facades of the mining companies. Resistance to change had almost become a standard operating procedure for many and consequently changes in technology had been slow in coming. The late 1950's and the 1960's saw a new awareness come into existence. As the mining company managements changed, there developed a realization that considerable efforts had to be made to bring the technology and social standing of the industry out of the dark ages and into the modern world. New advances were made in both metallurgical and mining technology. The 20th century technology of computers was accepted and became a standard tool of the industry.

Jan 1, 1971

By John Birkinbine

Much has been contributed to the Transactions of the Institute concerning the construction and operation of American blast-furnares ; but the following compilation is offered as possibly furnishing additional information upon the general features, dimensions, locations, capacities, etc., of the blast-furnaces of the United States; while, incidentally, the ores upon which they rely are noted in a general way. The paper is presented chiefly as a compilation, and the figures given are selections from most reliable sources, or averages calculated from official statistics, placed for convenient reference, with a view of assisting those who consult the Transactions in determining the present relative merits and importance of various sections of the country. The scope of the paper has been restricted to as few topics as possible, and all the details of special plants, or notable outputs have been ignored. While every effort has been made to give correct figures and data, the changes which are constantly taking place in the iron-producing industry, will, undoubtedly, by the time the paper is in print, develop some errors. It is difficult to determine which of the blast-furnace plants of the country should or should not be considered as upon the active list. A number which have not been in operation for years are still reported as active, some of which will scarcely be put in blast again, and others are handicapped so that they can only operate in times of abnormal profits. It is therefore scarcely probable that there are over 600 blast-furnaces in the United States which can properly be considered as active; but so many considerations affect the various plants, that, it being impossible to determine the exact number, I have relied upon the annual reports presented to the American Iron and Steel Association. Concerning the number of plants which could be stricken from the list, the Secretary of this Association says: "In January last (1885) we enumerated 669 furnaces, which included many stacks which had not been in blast for a very long time, and others which could not be operated except during short periods of exceedingly high prices for pig iron. We have gone over this list very carefully and have eliminated 10 anthracite, 19 bituminous, vol. xiv.—36

Jan 1, 1886

By FORTUNATO PEREIRA

(San Francisco Meeting, October, 1911.) I. GENERAL DESCRIPTION. The Department of Narino (formerly included in the Department of Cauca) is a narrow band about 170 km. (100 miles) wide in the southern part of the Republic of Colombia, FIG. 1.-SKETCH-MAP OF THE SOUTHWESTERN PART OF COLOMBIA. near the boundary of Ecuador, as shown in the sketch-map, Fig. 1. Its capital is Pasto, a small city of 25,000 inhabitants; the principal towns are Túquerres, Cumbal, Ypiales, Barbacoas, and Tumaco. The port on the Pacific ocean is Tumaco, and traffic in the interior is carried partly on the Patia river (steam navigation to the fluvial port of Barbacoas), and afterwards overland over poor roads by human bearers or on mule-back.

Aug 1, 1912

By AIME AIME

ASIDE from the annual dinner-dance, the two outstanding social events of the Annual Meeting were the dinner- smoker on Monday night and the informal dance on Tuesday night, both of which were held at the Commodore Hotel. Approximately 400 attended the former event, compared with 570 a year ago, and about 250, people were attracted to the dance.

Jan 1, 1933

By J. B. Bassett, E. S. Rowland

The experimental work reported herein firas inspired by the publication of a paper by Grange and stewart, in which it was suggested that at low chromium contents the effect of this element on the Ma point was greater than at higher chromium contents, It was argued that, if a small increase of chromium in solution in austenite caused a sharp lowering of the M, point, it might lead to an explanation of occasional unsolved stress cracking of SAE 52100 during heat treatment. Commercial hardening is carried out at temperatures of incomplete solution, leaving carbides available to enrich the austenite during any inadvertent increase in temperature, such enrichment of the austenite in chromium content would lower the M, point nearer room temperature where cracking is more likely to occur. According, it was decided to investigate the effect of chromium, in quantities between o and 2 pet, on the M, point of commercial steels. Fig I summarizes the data available on chromium steels. For purposes of comparison, the M, temperature values were corrected by means of the Grange and Stewart formulas to (I) Hypoeutectoid compositions: 0.50 pct carbon and 0.80 pct manganese (z) Hsereutectoid compos-sition': 1." pet carbon and O.35 pct manganese. Only the steels having compositions reasonably close to these corrected values were included, because large adjustments inevitably introduce increased error such as are experienced in using the formula. The straight lines of Fig I were drawn by the authors. These data obviously do not settle the question Of the effect Of chromium On the Md Oint, particularly at low chromium contents. While it is fairly well established that chromium causes the M, to be lowered when present in quantities of I pet Or more, Grange and Stewart1 have suggested that in small amounts (less than 1 pet) it is more effective in lowering the Ma point, while Klier and Troiano2 have suggested that in small amounts it is less effective in lowering the Ma point. Payson and Savage3 concur with Klier and Troiano and further suggest that the effect is not linear at these concentrations. Rose and Fischer4 report that small amounts of chromium actually raise the Ma point of a 0.20 carbon steel. Material Two series of 35 Ib induction heats were melted for this work, the analyses of which are given in Table I. One series was aimed at 0.50 pct carbon and 0.80 pct manganese with chromium additions in 0,25 pet increments from o to 1.5 pct with a single heat at 2.0 pct Cr. This series was considered necessary because the commercial heat treatment of SAE 52100 does not generally introduce more than about 0.60 pct carbon in solution in the austenite. The high

Jan 1, 1949

By Jerome F. Kuzmick

Condusions. From the work on aluminum powder, the following general con clusions can bc drawn: I. The physical properties of aluminum compacts, such as density. strength and ductility, increase with increasing pressure, up to the practicable pressure limits. 2. Good properties ill aluminum con pacts can be secured only by the use of high pressures, because it is neccssary to rupture the refractory oxide film on aluminum powder. 3. Considerable softening of the specimens occurs upon sintering. regardlers of the pressure used. General Conclusions 1. For relatively short-time sintering. molding pressure is a very important factor in the final physical properties of the sintered specimens. 2. The effect of pressure. is difierent for each metal, so that few general rules can be drawn that would apply to all metals. 3. In many cases, fur a particular metal powder and sintering temperature there is a critical pressure at which the best physical properties can be obtained. 4. The principles of cold work and in nealing and their effect on grain structure applied to massive metal also holds true for sintered metals. 5. Particle size, at least for electrolytic iron powder, does not have a. great effect on ultimate grain six. DISCUSSION [E. E, Schumacher presiding V.. V. Crane. *—I was particularly impressed with Dr. Kuzmick's work on tin IF not the illustration, particularly the Second one. a very good illustraition of hot preessing. in that

Jan 1, 1945

By W. David Menzie

An inventory of the mineral resources of a region is a most desirable basis for planning their systematic development. In the absence of appropriate samples upon which to base a reliable estimate of this inventory, investigators have resorted to a number of indirect approaches; the unit regional value concept forms the basis for one such approach. The produced resources of a region are a function of the inventory multiplied by the degree of intensity (some fraction between zero and one) of development of the resources. A convenient means of expressing this amount is to accumulate the weight and value of resource and to prorate the totals over the area represented by the unit sampled; i.e., weight and value per unit area or tonnes/km.2 and U.S. 1967 $/km.2. When this approach is used for the U.S.A., South Africa and Rhodesia the average value of (log.) U.S. 67$/km.2 for the states of the U.S.A. and South Africa are similar ($55,176 U.S.$67/km.2 and $52,538/km.2 respectively); whereas, Rhodesia is relatively underdeveloped (10,301 U.S.67$/km.2). On the other hand if the individual commodities are used as a basis for comparison, the U.S.A. shows the greatest diversity (67 commodities out of a possible total of 75) with South Africa next (50 commodities) and Rhodesia last with only 26 commodities. Since it is known that area and value are not simply related perhaps diversity is directly related to area. Again the kinds of commodities which have contributed the greatest value to the totals differs, with fuels (petroleum, coal and natural gas) predominating in the U.S.A. totals; whereas, South Africa and Rhodesia obtain their greatest contributions from gold, diamonds (S. Africa) coal and asbestos. In each case the greatest value of resources is produced from sedimentary rocks. As a somewhat different kind of example, consider a single resource (petroleum, the most valuable in the U.S.A.) over a large area (number of sampling units) the U.S.A. by state. Furthermore, assume that the model frequency distribution of the amount of petroleum (tonnes/km.2) is log normal. Then the present production fails to match the model first because 17 states (34% out of 50) have not produced petroleum. Of the remaining 33 states, Louisiana has produced the most (15,177 tonnes/km.2) and the frequency histogram is still skew. A spatial analysis of the distribution of the amount of petroleum by state shows that the samples (i.e., states) are not random; the non-producers and producers tend to cluster. It remains to be seen if this is indeed a true representation of the incidence of petroleum or is a function of the exploration philosophy currently in vogue.

Jan 1, 1977

By J. Spotts McDowell

Ackowledgments........................... 5 Introduction............................. 5 The Silica Minerals. Stability Relations......................... 6 Optical Properties........................ 9 Density.............................. 10 Melting Points....;..................... 10 Thermal Expansion..................,..... 10 Solubilities............................ 12 Identification of Cristobalite and Tridymite.............. 12. The Silica Refractories. Raw Materia1........................... 13 American Deposits....................... 13 Properties Determining Usability................ 15 Expansion on Heating..................... 16 Texture........................... 17 Silica Brick............................ 17 Manufacture........................... 18 Properties of Silica Brick .................... 19 Analysis ......................... 19 Density......................... 19 Porosity......................... 20 Strength....................... 21 Melting Point....................... 22 Specific Heat....................... 22 Thermal Conductivity................... 23 Expansion........................ 24 Effect of Rapid Temperature Change.........:... 26 Constitution......................... 26

Jan 1, 1918

By R. E. Somers

Discussion of the paper of R. E. SOMERS, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 101, May, 1915, pp. 957 to 996. A. C. LAWSON, Berkeley, Cal.-One point to which Mr. Graton (in summarizing the paper for us) called attention is that the author had not explained why some copper was fixed in the zone of oxidation. I recollect very well puzzling over that question at Ely, Nev., some years ago. Mr. Sales, in his paper on Butte,1 suggests the explanation. It is clue according to him to the paucity of pyrite in the primary ore. Where there is abundant pyrite sufficient sulphuric acid is formed by oxidation to take all the copper into solution and carry it to lower levels; but where the pyrite is scant so that insufficient sulphuric acid is formed, some of the copper is carbonated and so fixed in the gossan. The hypothesis, or some modification of it, as for example the combination of the sulphuric acid with lime, would appear to explain satisfactorily the fixation of the copper in the gossan as carbonate. I have, however, had no occasion in recent years to study the phenomenon. L. C. GRATON, Cambridge, Mass.-As I remember, the rocks in which the chrysocolla occurs in the Burro Mountains are both silicified and kaolinized. It seems probable that in surroundings deficient in carbon dioxide, complete oxidation of chalcocite may yield chrysocolla up to a maximum of half the copper in the chalcocite; while in rocks, like garnet contact zones and certain easily decomposable porphyries, surface decomposition appears often to yield silica in the necessary form to convert the copper of primary sulphides into chrysocolla immediately and directly upon oxidation.

Jan 12, 1915

By Robert W. Fullerton, Donald T. King

INTRODUCTION AND THEORY by Robert W. Fullerton In coal preparation plants, as in any industrial operation where raw materials are handled, nuisance problems arising from the generation of dust are inevitable. Devices for the control or collection of dust are there- fore essential components of the plant process equipment. The general term "aerosol" is applied to small particles suspended in a gaseous medium, usually air, whose velocity under the force of gravity is small enough that the particles remain suspended for a reasonable length of time. Aerosols can be classified as dust, smokes, fumes, mists or fogs. Dust includes particles originally formed by pulverization of materials by such processes as crushing, grinding, drilling, blasting and abrasion. Smoke includes particles formed from the burning of organic materials. Fumes are particles formed by processes such as condensation and sublimation, usually at high temperatures. Mists or fogs are particles formed by the condensation of water or other vapors on some nuclei. The size of aerosol particles is generally designated in units of microns, there being 1000 microns to a millimeter and 25,400 microns to an inch. Particles of about 10 microns or above are visible to the naked eye. Table 14-1 shows size characteristics of the general classifications of particles discussed above and includes typical examples of particles commonly en- countered. Table 14-1 also shows the relationship between micron size and standard screen mesh sizes. Smoke and fume are usually in the range of 0.01 to one micron, dusts are in the range of one to 400 microns, mists are in the range of 0.1 to 100 microns, and fogs are in the range of one to 100 microns. For purposes of dust control, particles greater than 10 or 20 microns in size are considered large, particles one to 10 microns are considered fine and particles below one micron are ultrafine. Sources of Dust Because coal is relatively friable, the mining and subsequent handling operations break part of the coal into dust that can be readily carried by currents of air. In a coal preparation plant mechanical handling operations such as unloading, transferring from one belt to another, screening, cleaning, and crushing in a dry state result in the generation and release of varying amounts of additional dust. The dust problem, of course, is much less serious in plants employing entirely wet processing. In addition to dust from handling operations, thermal drying of the fine coal product frequently presents another dust collection problem. Most coal driers are

Jan 1, 1968

By J. B. Stubbins, R. A. Blais

Extensive geological work was initiated — and continues — when operations of the Iron Ore Co. of Canada commenced in the Labrador-New Quebec area. Such geological operations include: mapping, test pitting, drilling, underground workings, volume factor and structure tests, and the calculation of ore grades and tonnages. Details of such work are given. Development is carried sufficiently ahead of mining to provide reliable tonnage and grade estimates and allow final mine planning. In order to make full use of geology in mining operations, the pit engineer combines the duties of geologist and mining engineer. The iron deposits of the Knob Lake range are located in the central part of the Labrador peninsula, a territory nearly twice the size of Texas, which is bounded by Hudson Bay on the west, Hudson Strait on the north, the Atlantic Ocean on the east and the Gulf of St. Lawrence on the south. The mining district proper is about 1000 miles northeast of Toronto. A 360-mile railroad links this mining area to the port of Sept-Iles on the Gulf of St. Lawrence. Schef-ferville, which is only a few miles from the open-pit mines, is the center of operations of the Iron Ore Co. of Canada. It has a population of nearly 5000. The nearest settlement is Labrador City, some 120 miles to the south, where this company is erecting a large plant for beneficiating its huge reserves of local low-grade iron ores. HISTORY The mineral possibilities of the area were recognized as early as the end of the last century, when A.P. LOW' of the Geological Survey of Canada made his famous trek across the Labrador Peninsula. After mapping several belts of iron formation, Lovr recommended that the area be thoroughly prospected for iron. In 1929, two well known Canadian geologists, J.E. Gill and U'.F. James, led a private expedition in central Labrador and discovered the first deposit of high-grade iron ore near what is now the Ruth Lake Mine. In 1936 the Labrador Mining and Exploration Co. was formed to 11ake over a prospecting concession of over 20,000 sq miles in central Labrador. An adjoining concession of 3900 sq miles in New Quebec was obtained in 1942 by Hollinger Consolidated Gold Mines, which had just Purchased the Labrador Co. The same year the M.A. Hanna Co. Purchased an interest in both exploration companies. From 1942 to 1950 extensive exploration was conducted by the Hollinger-Hanna technical staff to systematically appraise these vast concessions. More than 40 deposits of high grade ore were found and, by the end of 1950, the total ore reserves reached 418 million tons. In 1949 five American steel companies joined the Hollinger-Hanna interests and formed the Iron Ore Co. of Canada. Financing and full-scale construction were decided upon in 1950. This included the construction of a 360-mile railroad through very difficult terrain, the erection of two hydroelectric plants, the installation of terminal port facilities at Sept-IIes, the building of a modern town-site at Schefferville, the construction of crushing and screening plants, and the preparation of deposits for mining. Ore was first shipped in July 1954. Total open-pit mine production to date is 66 million long tons of direct-shipping ore. GEOLOGICAL ENGINEERING The above achievements would not have been possible without irtegrated teamwork of people of diverse skills and extensive use of geology. In their paper on the role of geologists in the development of this iron ore field, (Gustafson and Moss1 rightly emphasized the difficulties facing the early workers in the area. In an uninhabited land with no roads or railroads and no navigable rivers leading to the interior, everything had to be flown in. It was not until 1948 that aerial photographs and adequate base maps became available. In spite of these and other difficulties, an impressive amount of field work has been done since 1942. Nearly all this work has been directed by geological engineers and geologists. About 15,000 :sq miles have been geologically

Jan 1, 1962

By R. P. Alger, J. S. Wahl, C. W. Johnstone, J. Tittman

To overcome the problems of mudcake and hole irregularities, the new compensated formation density logging device employs two detectors spaced at different intervals from the source. The detector at the shorter spacing is particularly sensitive to the density of material immediately adjacent to the face of the pad. The contribution of this material, which includes mudcake and minor wall irregularities, affects the response of each detector to a different degree. The signals from both detectors are combined to give automatically a density correction which is added to the uncompensated density information from the detector at the longer spacing. Both the compensated density measurement and the amount of compensation are then recorded on the log. With the unwanted borehole effects removed, the measurement is recorded directly in terms of bulk density on a linear scale. INTRODUCTION Formation density is a very useful and diagnostic parameter for formation evaluation. When the matrix lithology is known, porosity is accurately and readily computed from density data.'-" hen the density measurements are used with other porosity-responsive measurements, such as Sonic and Neutron logs, both lithology and porosity may be defined with good accuracy."'" In the past, however, application of density logs was complicated by the need for corrections to obtain true formation densities from the log values. Mudcakes on permeable formations and roughness of the borehole walls have been particularly troublesome since, in each case, the device was prevented from direct contact with the formation. ~ttempts have been made to correct for such conditions by making a simultaneous caliper log, estimating pad standoff, and assuming knowledge of the composition of the intervening materials. While such corrections are frequently accurate, they are not always reliable because of uncertainties in the pad standoff and material composition. A further complication was the necessity for manual conversion of log counting rates to density. The newly introduced compensated formation density logging device (FDC) automatically corrects for mudcake and minor wall irregularities, and provides a log that is scaled directly in bulk density. The purpose of this paper is to discuss briefly the equipment, to explain the theoretical considerations involved in the compensation, and to present field examples of this new log. COMPENSATED FORMATION DENSITY EQUIPMENT The FDC tool incorporates two major advances over previous density logging devices: a second detector, spaced closer to the gamma ray source to provide increased sensitivity to material close to the pad; and the automatic derivation of a corrected formation density from the two counting rates. The arrangement of the source and detectors is shown in Fig. 1. The longer spacing detector is at the same spacing from the source and gives the same response as the single detector in the previous uncompensated device. By appropriate combination of the outputs of the two detectors, the FDC tool is able to compensate in large measure for effects of mudcake and hole rugosity. This is achieved, as will be described later, without specific knowledge of either the thickness or the nature of material between the pad and formation. To obtain corrected formation density, the two count rates are automatically processed by an analog computer in the surface panel. More specifically, the computer derives a value of uncompensated formation density from the long-spacing counting rate, computes a density correction p using both the long and the short spacing count-

Jan 1, 1965

By C. B. E. Douglas

In an interesting article on evaluation of the water problem at Eureka, Nev., W. T. Stuart describes how a difficult water problem, or one phase of it, may be evaluated by means of a small scale test. Test data are plotted by a method rendering, under certain conditions, a straight-line graph that can be projected to show how much the water table will be lowered by pumping at any specified rate for a given time. A formula is then used to determine the size of opening, or extent of workings, necessary to provide sufficient inflow to enable pumping to be maintained at that rate. At first glance this might seem the answer to a miner's prayer, but a word of caution is in order. It may not be the whole answer. Moreover, results obtained by the method described are reliable only for conditions approximating those assumed. Even where conditions do not meet this requirement, however, it may be possible to draw helpful inferences from the results, perhaps enough to facilitate another approach to evaluation of a problem.

Nov 1, 1955

By J. D. Livingston, H. E. Cline

Cu-Pb alloys in the vicinity of the monotectic composition have been directionally solidified under a high temperature gradient at rates up to 2 X l0-' cm per sec. Over a wide range of compositions, high growth rates yield a composite structure consisting of continuous rods of lead in a copper matrix. This range of compositions increases with increasing growth rate, in agreement with arguments based on the relative velocities of composite growth and the growth of copper dendrites or lead drops. The breakdown of the composite structure at slow growth rates is explained in terms of the relative interphase surface energies. The observed interrod spacings of the composite structure are large compared with the predictions of the Jackson-Hunt equations of eutectic growth. ThE directional solidification of many eutectic alloys produces fine composite structures of parallel lamellae or rods. There has been considerable interest not only in the fundamentals of this two-phase solidification process,'-3 but also in the interesting physical properties produced by such regular and aniso-tropic microstructures. Composite structures can be grown only over a limited range of composition, beyond which coarse primary dendrites of one phase appear. In organic eutec-tics, this composition range of composite structures has been shown to increase with increasing growth rate.7"10 These results were explained in terms of the relative velocities of composite (coupled) growth and dendritic growth. Although similar arguments should apply to metallic eutectics,11-13 suitable experimental results are lacking. In contrast to the work on eutectics, the directional solidification of monotectic alloys has received little attention. (The monotectic reaction is similar to the eutectic reaction, except that one of the resulting phases is a liquid, which subsequently solidifies in a separate reaction at a lower temperature.) Directional solidification of some monotectic alloys'4715 yields regular rodlike microstructures, whereas in other cases macroscopic separation of solid and liquid phases occurs.16 chadwick17 rationalized these results in terms of the probable relative magnitudes of the various interphase surface energies. A recent study of chill-cast Cu-Pb alloys18 revealed a fine rodlike microstructure in alloys near the monotectic composition. It was decided to investigate the directional solidification of such alloys, and to determine the range of composition and growth conditions yielding composite structures. The Cu-Pb system is convenient for such a study, both because it is simple metallurgically, with no compound formation and negligible solid solubilities, and because its basic properties are well-documented. Recent literature on the Cu-Pb system includes studies of bulk thermo-dynamic properties,'g surface energies,20"21 densi-ties,25 and diffusion constants.a6 A similar study of the directional solidification of Cu-Pb alloys was recently undertaken, independently, by Kamio and Oya." EXPERIMENTAL Alloys were prepared by melting 99.999 pct Cu and 99.999 pct Pb in a graphite crucible, stirring well, and pouring into a cold graphite mold. Rods 0.175 in. in diam were machined from the ingots. Alloy compositions studied ranged from 25 to 55 wt pct Pb. Samples were placed in graphite crucibles 5 in. long with 4 in. OD and 0.035-in. walls. They were melted under flowing argon in a vertical, two-zone. platinum -wound furnace. A voltage stabilizer was used to minimize fluctuations in input power. The narrow specimen diameter minimized convection. Directional solidification was achieved by driving the crucible downward into a +-in. hole in a water-cooled copper toroid. The toroid was located immediately below the narrow end zone of the furnace. The end zone was separately powered to maintain high local temperature. Therefore a high temperature gradient (approximately 300 deg per cm) was maintained in the specimen throughout the run. The crucible motion was screw-driven. and a wide range of drive speeds were available. The limited rate of heat removal caused a thermal lag in the specimens at high drive rates. However. temperature-time curves from thermocouples imbedded in a representative sample indicated that the average growth rate still approximately equaled the drive rate. Although the specimens were initially homogeneous, melting and re solidification redistributed the lead. producing composition variations of several percent along the specimen length. (During melting. lead melted first and ran down the sample surface. Rapid freezing tended to reproduce the resulting composition gr~dient, but slow freezing did not because a slow-moving interface tended to reject lead. as discussed later.) To determine local composition. ;-g samples were cut from regions exhibiting various microstructures and were chemically analyzed for lead content. Micrographs were taken on as-polished or lightly etched surfaces. Three-dimensional structure of the lead network was viewed with a scanning electron microscope after removal of some of the copper matrix with nitric acid. RESULTS Several different microstructures are observed, depending on composition and drive rate. Because melting and resolidification produced composition gradients, results are best presented in t&ms of final local composition, rather than initial or average composition. The ranges of local compositions and drive

Jan 1, 1970

By V. R. Garfias

INTRODUCTION FOR a number of years the senior author has been interested in the various geologic and engineering problems involved in the development of the petroliferous districts of northeastern Mexico, having in a previous paper 1 endeavored to present a summarized statement of the information relating to the geology and soil resources of this region. Of the many interesting geologic phenomena, perhaps those which have been the object of more speculation relate to the igneous intrusions which, in places, have a controlling influence on the accumulation of oil in commercial quantities, a relationship which has been tentatively explained by various observers with as many interestingly different views. The authors of the present paper aim to record, in the course of a general discussion of the various viewpoints, some additional data, and present further tentative conclusions with a view to rounding out an up-to-date summary of the subject. The greater part of the area in question lies in the State of Vera Cruz, only a northwest fraction being in the State of San Luis Potosi. Vera Cruz is bounded on the north by the State of Tamaulipas, the northernmost of the Mexican States along the Gulf. The topography of the States of Tamaulipas and Vera Cruz and of Texas and Louisiana to the north, is controlled by the Gulf coastal plain which in northern Vera Cruz has an average width of about 60 miles, the transitional topography between that of the rugged flanks of the Sierra and the lowlands of the coast being made up of a series of terraces and irregular hills and valleys.

Jan 8, 1917

By C. L. Berrien

Before the present company was formed, in 1916, each group of mines comprising the old organizations made its detailed daily and monthly mine cost records along the lines used before the consolidation; that is, there was no attempt made to standardize and compare the stope costs of all mines. The general cost sheets for all mines, however, were standardized, and cumulative labor cost sheets were compiled in the general superintendent's office. At most of the mines, a daily record or distribution sheet for each working place was kept, showing the number of men, hours of drilling, hours of timbering, hours of tramming, cars of ore, cars of waste, sticks of powder and feet of fuse. This information was kept by each shift boss and entered on the distribution sheet by him or, at some mines, by a tram boss. The superintendent solved his own problems under the direction of the general superintendent, but without coming in touch with other superintendents, either through records or general conferences. Probably 95 per cent. of the stopes were square-set worked by day's pay; there were some back-filling and shrinkage stopes. Many of the development places, such as shaft sinking, station cutting, drifting and raises had always been run by contract. These contracts were given, for no definite period, at so much per linear foot and were measured monthly, or when completed, the men being paid monthly. In some cases, fairness to the employee was not maintained. On the whole, there was no standardization. There were no stope contracts, because of the objections of the Western Federation of Miners to general contracting in the mines. Changes in Stoping Methods Early in 1916, W. B. Daly, then general superintendent, and the author, then assistant general superintendent, visited the Southwest mining districts with the object of finding some improved mining

Jan 1, 1923

By C. L. Berrien

Before the present company was formed, in 1916, each group of mines comprising the old organizations made its detailed daily and monthly mine cost records along the lines used before the consolidation; that is, there was no attempt made to standardize and compare the stope costs of all mines. The general cost sheets for all mines, however, were standardized, and cumulative labor cost sheets were compiled in the general superintendent's office. At most of the mines, a daily record or distribution sheet for each working place was kept, showing the number of men, hours of drilling, hours of timbering, hours of tramming, cars of ore, cars of waste, sticks of powder and feet of fuse. This information was kept by each shift boss and entered on the distribution sheet by him or, at some mines, by a tram boss. The superintendent solved his own problems under the direction of the general superintendent, but without coming in touch with other superintendents, either through records or general conferences. Probably 95 per cent. of the stopes were square-set worked by day's pay; there were some back-filling and shrinkage stopes. Many of the development places, such as shaft sinking, station cutting, drifting and raises had always been run by contract. These contracts were given, for no definite period, at so much per linear foot and were measured monthly, or when completed, the men being paid monthly. In some cases, fairness to the employee was not maintained. On the whole, there was no standardization. There were no stope contracts, because of the objections of the Western Federation of Miners to general contracting in the mines. Changes in Stoping Methods Early in 1916, W. B. Daly, then general superintendent, and the author, then assistant general superintendent, visited the Southwest mining districts with the object of finding some improved mining

Jan 1, 1923