Search Documents

By E. H. Lancaster, M. E. Mitchell

A MUD-conditioning program found to be very effective for drilling and completion operations on routine field wells requiring relatively short drilling time involves a moderate alkaline-tannate-bentonite treatment resulting in an ultimate filtration rate of 10.0 cc or less (API test). Mud weight schedules are planned from pressure information on completed wells in producing reservoirs and drill-stem test data obtained on other zones not being produced at present. In general, terminal mud viscosities average 45 sec (Marsh). This value has been found to be sufficient to remove cuttings from the well bore on the average well, with the slush pumps in general use on the rigs. On field wells requiring drilling times in excess of approximately 30 days, an alkaline-tannate-lime-bentonite treatment has been effective in maintaining desirable viscosities and filtration rates with a substantial reduction in chemical costs. This system has shown particular advantage on heavily weighted muds and those with abnormal flow-line temperatures. For the most part, the chemical treatment utilized in wildcat drilling follows closely the program used on field wells, depending on depth and duration of drilling operations. Wildcat mud programs are planned from information available from various geologic and operational sources, taking into consideration the possibility of encountering mud problems of a special nature in the wildcat area. Careful planning of wildcat mud pro- grams has proved to have definite value in avoiding most serious mud problems. An analysis and recommended treatment are presented on several special. mud problems which have been encountered in the area in the past. Those problems discussed are lost circulation, blowouts, sloughing shale, excessive chloride contamination, sulphate contamination, and prevention and correction of cement contamination. Introduction Drilling-mud control in the Southwest Texas area, in general, does not involve the multiplicity of problems encountered in other coastal areas. For instance, it is rare that a mixture of problems such as lost circulation, abnormal pressure, severe sloughing shale, and others, occurs on one well within close enough limits in vertical depth not to be taken care of by a sensible casing program, together with a relatively clear-cut mud program. There are conditions such as the fairly widespread occurrence of abnormal pressure in the lower Frio and Vicksburg zones, and the tendency for sloughing shale in the Jackson section which make for rather expensive mud control. However, the availability of fairly accurate geologic and operational information makes possible a reasonable degree of standardization on mud treatment over a relatively large area. It may be said that, over most of this area where drilling is currently in progress, the natural mud made is very poor in quality, but responds readily to moderate chemical treatment to yield very good wall-building characteristics. AS far as field development drilling is concerned, the mud engineer's principal job, once the routine treatment best

Jan 1, 1949

By A. P. Svenningsen

DURING the work at the test mill in Morenci, it was determined that a suitable feed for the ball mills could be made by a single pass through a short-head cone crusher. These crushers did not require a closed circuit delivering only a screen product to the mills, such as is the practice in some concentrators. By no means does this mean that the practice in these other concentrators is wrong, but just that the Morenci ore can be most economically crushed and ground in this manner. Therefore, the design of the secondary crushing plant was simply a problem of taking 25,000 tons of ore per 16 hour day from the primary crusher, this ore ranging in size from fine particles to 10 or 12 in., and reducing it to minus 3/4 in. Inasmuch as outages must be contended with in any crushing plant, it was assumed that the crusher would operate at full capacity for approximately only twleve hours per day, which is three-quarter capacity for the 16-hour shift. With this in mind, it was necessary to design a crushing plant which would average approximately 1600 tones per hour for the 16-hour day, or 2000 tons per hour for slightly over 12 hours per day.

Jan 1, 1942

By P. D. Zemany, G. W. Sear, B. W. Roberts

Vanadium metal is embrittled by hydrogen at a temperature as low as 250°C when held in the presence of manganese metal and water vapor in a rough vacuum. It is established that the property changes are caused by the catalytic decomposition of water vapor at the vanadium surface and the diffusion into and solution in the vanadium of the resultant hydrogen. It is found that manganese is a necessary component of the catalyst. The manganese is transported in the vapor phase by an unknown molecule. A deuterium tracer experiment demonstates the role of water vapor in the embrittle-ment process. VANADIUM metal foils were observed to become embrittled' at a temperature of about 300 °C when held in the presence of manganese metal and a small amount of moist air, This paper describes the investigation to find the embrittling agent and an understanding of the relatively low temperature reactions that are involved. Experimental The vanadium metal foil used was prepared by cold-rolling and pack-rolling 32 mil sheet" in a series of steps down to 1 mil foil. The original observation was confirmed by sealing vanadium foils of 3 x 10 sq cm into individual Pyrex tubes with manganese powder† and a con- trol tube containing only the vanadium foil. These tubes were evacuated to 10 -5 mm Hg without baking and sealed. After heat treatment for 200 hr at 300°C, the control foil showed no change in duetility, whereas the foil contained in the manganese— containing tube was embrittled. The visual appearance of each was unchanged. A series of Pyrex sample tubes, about 2.5 cm diam and 25 cm long, were prepared, each containing a 3 x 10 sq cm piece of foil and 5 g manganese powder at the lower end of the tube. By reducing the time of anneal and the temperature of these samples, it was found that embrittlement could be created at 250°C in a time as short as 1 hr. Since the vanadium metal used here has been drastically cold-worked by rolling, it is assumed that it contains a maximum number of dislocations. To check the possible necessity of dislocations in this low temperature reaction, a vanadium foil sample was annealed in Vycor for 2 hr at 800°C to re crystallize and reduce the dislocation concentration. Metallographic examination showed grains which were not visible before annealing. The embrittlement procedure was carried out at 300°C and 3 hr. Upon checking the foil no embrittlement was observed. Further experiments demonstrated that about 6 hr at 300°C are required to create embrittlement in the foil. This delay in the onset of embrittlement in the vanadium foil suggests but does not prove that dislocation channels play a role in the embrittlement phenomena. If manganese metal is necessary for this low temperature embrittlement, do other elements in the transition metals group yield the same result? To check this qualitatively, a group of elements of similar atomic radii were obtained and sealed as before into Pyrex tubes with a sheet of vanadium foil. These tubes were annealed at 250°C for 6 hr and included (with radii)-2 A1 (1.4A), As (1.25A), Be (1.2A), Co (1.25A), Cr (1.45A), Cu (1.25A), Fe (1.25A), Ga (1.2A), Ge (1.25L%), Mn (1.3A), Ni (1.25A), Si (1.2A), Ti (1.45A), Zn (1.3A), air, H,O, 10 cm Hg of dry hydrogen, and MnO, powder. Upon testing the above sample foils for brittleness, only the manganese-containing tube yielded a brittle foil. Manganese Transport—To eliminate contact of manganese metal powder and vanadium foil, sample tubes were prepared with fritted glass barriers. The embrittlement reaction was still found to occur. Thus, the mode of transfer of manganese is certainly vapor transport. A vanadium foil was embrittled by this mechanism in an evacuated Pyrex tube for 8 hr at 300°C. By means of X-ray fluorescence analysis,' the amount of manganese added to the surface was established at 5 ±2 x 10 -6 g per sq cm. Since the average rate of manganese deposition is known, an effective average pressure of an assumed carrier compound can be computed. ___ P = M/T v2p mkT

Jan 1, 1959

By W. C. Knopf, G. Samsel

For several years International Minerals & Chem-ical Corp. has used a radiation method to assay potassium content of products from potash and feldspar beneficiation. The procedure is rapid, accurate, and inexpensive and is easily handled, if necessary, by nontechnical personnel. Data are presented to show the accuracies that may be expected if the technique is used for control of pilot plants or large-scale plants. Natural potassium is composed of three isotopes —K, K and K. Five other isotopes, artificially produced, have been detected. In natural potassium only the K isotope, with a half life of 1.4x10 years, is radioactive. Its modes of decay are beta and gamma rays, positrons, and x-rays. Only the more abundant beta rays, however, are important in radiation measurements using geiger tubes. Barnes and Salley' measured radiation of potassium salts in solution in 1943. Gaudin and Parnell2 first reported the use of solid salts arranged in a vessel surrounding the ß counter in 1948. Later, Scheel used the method to assay potassium content of various crude and finished potash salts. Experimental: Dip-type Geiger-Muller tubes (TGC-5) supplied by Tracerlab Co. were used in all radiation counting measurements. The tube was encompassed by a glass container about M in. larger in diameter than the tube. This container, which served as a sample holder, was closed at the bottom with a rubber stopper to facilitate removing the samples. Samples were not weighed, but about 40 g of sample were needed for each test. Electrical impulses from the tube were counted on either a Tracerlab scaler or a rate meter. To obviate the need for constant attendance, preset features were incorporated into the scalers, so that at a predetermined time or count the units were automatically deactivated. When rate meters were used, counting rates were read directly from instrument or from a recorder used in conjunction with the rate meter. Each tube was calibrated, according to the manufacturer's instructions, to determine the correct operating voltage to insure reproducible results. A linear calibration plot of percent K2O vs counting rate was also obtained for each tube by recording the counting rate plus background count of several standards of different K2O content chemically analyzed by the chloroplatinate method.' These standards were of approximately the same particle size distribution as samples to be assayed. Specific background count caused by cosmic rays and other surrounding radiation was checked periodically by counting a sample of pure NaCl. Fig. 1 is a representative calibration plot. Assays were determined directly from the standard plot or calculated by subtracting the background count from the counting rate, then multiplying by the slope of the line. Chemical assays of the test samples were made by the Sherril method," a flame photometric technique, or the chloroplatinate method. Data: The radiation assay method has been used for three years by International Minerals & Chemical Corp. in the laboratory and in pilot plants processing ores containing potassium. These dry concentration plants process sylvinite and langbeinite ores at Carlsbad, N. M., and feldspar ores at Top-sham, Maine. Sylvinite ore is predominantly a mixture of syl-vite (impure KCl) and halite (impure NaCl). Contaminants include sulfates, such as langbeinite (2MgSO - K2SO4), kieserite (MgSO H2O), poly-halite (MgSO4.K2SO, 2CaSO, . 2H2O), and slimes. Langbeinite ore is predominantly langbeinite and halite with small amounts of sylvite, sulfates other than langbeinite, and slimes. Several variables, in addition to correct calibration and standardization of tubes, were found to be important in obtaining reproducible results. Particle size distribution of standard samples should be

Jan 1, 1959

By H. Landsberg

Biological as well as geological research has made very successful use of the qualities that the physicists have detected in radioactive substances. Outstanding examples for the vast new fields opened in this part of the border-land between the disciplines of geology and physics are the "radio thermal geology" [July, 1909, see 1 of "References" at end of paper] and all that is connected with the use of the radioactive disintegration clock for the age-determination of rocks and minerals [2]. In structural geology, not unlike to recent bi-ological uses of radioactive material, their "tracer" properties were helpful. Changes in Radon concentra-tion in soil-air, especially accumulations, led to hidden crevices and fault-zones. High contents of Radon in spring-water gave clues as to the types of rocks they had flowed through [3, 4). One specific application of the small admixtures of radioactive material, however, has only lately found some atten-tion and that is their use in linking beds of sedi-mentary strata otherwise only poorly identified be-cause of the lack of fossils or other characteristic properties. To be useful for this purpose, two con-ditions have to be fulfilled: (1) The amount of radioactive material per unit-weight of rock in a given horizon should be uniform over a large area; (2) this same amount should change fairly rapidly in the vertical succession of layers.

Jan 1, 1940

By Dever C. Ashmead

COAL companies in the anthracite region are studying various methods of mining that will permit a considerably shorter life of gangway and therefore a decrease in the maintenance charges. Maintenance charges in the upkeep of gangways where the measures are steeply pitching are high due to the excessive cost of the replacement of timbers and the cleaning up of falls. Therefore, if the length of gangway in the coal beds can be decreased and the mining more concentrated, the life of the coal gangways will be decreased and consequently the maintenance charges will be lower per ton of coal produced. Customary practice in the anthracite region is to drive long coal gangways and to work the breasts as the gangway from which they were driven is advanced.

Jan 1, 1925

By S. A. Lever, R. Hultgren

The solidus is usually the least satisfactorily determined portion of a phase diagram. Cooling curves, which succeed well with the liquidus, show the solidus inaccurately or not at all because of segregation which occurs during freezing. Heating curves of carefully homogenized alloys might be expected to indicate accurately the solidus, but they are seldom used. Dynamic methods involving heating or cooling are never completely satisfactory because of uncertainty as to whether equilibrium is attained. A static method in which the specimen may be allowed hours, days, or even weeks to attain equilibrium is to be preferred. In a static method a solid solution, for example, is first made thoroughly homogeneous, then heated to successively higher temperatures. After sufficient time at each temperature to assure equilibrium, some property is measured which should alter strikingly when melting begins. Microscopic examination can be used to detect the beginning of melting, but the method is tedious since the specimen must be quenched, sectioned, polished, and etched before each examination. Of all the physical properties which change on melting, electrical resistance is probably the most satisfactory to measure. The measurement may be made while the specimen is at temperature without damage to the specimen. It may be repeated indefinitely to ascertain when equilibrium has been achieved. Measurements may be made on a single specimen over the whole range of temperature. Most metals approximately double their resistance on melting. Since an accuracy of a few tenths of a percent is easy to achieve, the method is highly sensitive to the beginning of melting. In spite of these advantages, which have been perceived for a long time,l,2 a reasonable search of the literature has failed to reveal a single case in which the method has been satisfactorily applied in practice to the determination of solidus temperatures. The use of electrical resistance measurements appears to have been confined in practice to changes in the solid state. In the work described in the following pages we have applied the electrical resistance method to the solidus of the lead-tin system. We have found the method to be convenient, reproducible, and highly sensitive. We chose the lead-tin system because it leads to few technical difficulties. Furthermore, a number of determinations of solidus have been made in this system by various methods and results could be checked against them. However, all published results are not in good agreement with one another, so this work should help in determining the solidus more precisely. The Lead-tin Diagram Because of its commercial importance, there have been numerous investigations of the lead-tin diagram. The results of the most recent work on the solidus are indicated in Fig 7, as well as the results of the present work. The works of Honda and Abe3 and of Stockdale4 agree fairly well with each other and with the present work. Jeffery's5 data indicate the solidus to be about 50°C lower. Honda and Abe3 used differential thermal analysis on both heating and cooling cycles. Stockdale4 used the microscopic method and also differential heating curves. Stockdale's results were about 4" higher than those of Honda and Abe at low tin contents and lower at higher tin contents. These results also agree with those of Rosen-hain and Tucker.= Jeffery5 used electrical resistance measurements of the alloy as it was being heated or cooled. Apparently he did not attain equilibrium as his results are about 40°C lower than those of Stockdale4 or Honda and Abe.3 MATERIALS AND METHODS The lead and tin used were of high purity. They were supplied by the American Smelting and Refining Co., who gave the following analyses: Lead: silver, 0.0016 oz per ton; copper, 0.0008 pct; cadmium, 0.0007 pct; zinc, 0.0002 pct; arsenic, 0.0003 pct; antimony, 0.0002 pct; bismuth, 0.0005 pct; tin, 0.0001 pct; iron, 0.0020 pct; lead (by difference), 99.995 pct. Tin: antimony, 0.037 pct; arsenic, 0.020 pct; bismuth, 0.004 pct; cadmium, trace; copper, 0.025 pct; iron, 0.004 pct; lead, 0.020 pct; nickel and cobalt, 0.005 pct; silver, 0.0005 pct; sulphur, 0.005 pct; tin (by .-difference). 99.88 pct. One hundred grams of metal with the desired proportions of lead and tin was weighed out to the nearest one-tenth of a milligram. The mixture was placed in a silica crucible, covered with charcoal, and melted in a reducing atmosphere in a gas-fired furnace. The alloy was well stirred. Chemical analysis of two of the alloys checked closely with the weighed portions. The compositions of the remainder of the alloys were taken directly from the weighings, without chemical analysis.

Jan 1, 1950

By N. Standish

Heat transfer coefficients have been measured in beds of various packings irrigated with mercury and molten fusible alloy countercurrent to hot gases. The measured coefficients for both systems were found to increase with gas velocities and liquid rates. Correlations were determined which show this dependence and also indicate that heat transfer in these systems is influenced by the liquid flow characteristics and the thermal conductivity of the gas and the solid packings. A heat transfer model has beer2 proposed which explains the various features of the experimental results. On the basis of this study, which gives an insight into the heat exchange in the melting zone of the blast furnace, it was concluded that by comparison with the furnace stack heat transfer coefficients are about 1.5 times higher in the melting zone. EACH year large tonnages of metal are produced in operations which, in part, involve liquid metal irrigation of "packings" countercurrent to hot gases. The melting zone in blast furnaces and in cupolas is a good example of packings irrigated with a liquid melt countercurrent to gases. In all instances of this kind large amounts of heat are exchanged and it is desirable to have some knowledge of heat transfer phenomena involved in these systems. So far the most common method of analyzing furnace efficiencies, fuel requirements, and the general thermal state of the furnace has been through the use of heat balances. As heat balances are essentially statements of the first law of thermodynamics they give no real indication of the factors which govern heat transfer between phases in the various zones of blast furnaces. Hence, rational improvement in production efficiency and the development of theoretical models is only possible if the heat transfer characteristics are known at every stage of the process and related to the important variables involved. This has been generally recognized for some time but it was only recently that Kitaev et al.' have produced a comprehensive treatment of heat transfer in solid-gas countercurrent systems such as the blast furnace stack and the packed bed regenerator. Using their treatment it is now possible to predict the effect of particle size, thermal conductivity, bed porosity, and the flow rates of both the gas and the solid material on the heat transfer in the blast furnace stack. However, the stack of a blast furnace is only one part of an integral unit for which the heat transfer analysis cannot be complete without also considering the heat exchange in the melting zone. The complexity of heat transfer processes in this region of the furnace has so far escaped quantitative description. Yet, the melting zone accounts for a greater amount of heat exchange than all the other zones of the furnace put together. Moreover, if the reduction of oxides in the melting zone proceeds in part in the liquid state the importance of heat transfer on furnace productivity and on the metal and slag temperatures is obvious. THEORY Heat transfer for two-phase flow in packed beds is a complex problem involving a number of heat exchange paths for which interphase areas are not known with any degree of certainty. Analytical solution is, therefore, difficult. This difficulty is emphasized by noting that Rabinovich~ and Luck have only recently solved the steady-state heat transfer for simplified two-phase heat exchangers of known area. However, useful progress can be made for the system considered by making a not unreasonable assumption that the usual heat transfer considerations apply and restricting treatment to the steady state. For these conditions the rate of heat transfer dq in a height dz of a packed bed of unit area is: dq = UaATdz [I.] Integration of Eq. [I] then gives the total heat transferred: assuming both U, the overall heat transfer coefficient, and a, the interphase area, to be independent of bed height. Since a, in these systems, is unknown it is convenient to combine this term with U. The group U, then represents the overall heat transfer coefficient on a volumetric basis. If AT is linear with q, then for a bed of unit volume Eq. [Z] can be integrated to give: is the log mean of terminal temperature differences. From Eq. [3] U, can be readily calculated as q and {AT)im are experimentally obtained quantities, but a difficulty arises in interpreting its meaning. Two approaches are possible depending on whether the effect of packing in the transfer of heat is neglected or not. If the packing is thermally decoupled then the resistance concept gives the relationship: which states that the overall resistance is the sum of the gas phase and the liquid phase resistances (assuming areas are equal throughout). Because the resistance to heat transfer in liquid metals is negligible by comparison with that of the gas,4 Eq. [4] can be simplified, i.e.:

Jan 1, 1969

By Harry M. Mikami

Chromite is the only ore mineral of metallic chromium and chromium compounds and chemicals. Because of this fact, chromite and chrome ore are used synonymously in trade literature. In commercial market quotations, chrome ore is the term commonly used. Chromite per se, because of properties imparted by its chromium content, is used in refractories and in special purpose molding sands for metal casting. There are many other minerals containing some, generally minor, amounts of chromium, but none are commercial sources of the element (Thayer, 1956). Chromium and chromite have many diverse uses that, directly and indirectly, critically affect vast segments of our modern industrial system. Most important are probably the metallurgical applications wherein chromium is a component of heat-, abrasion-, corrosion-and oxidation-resistant and high-strength alloys of many types. Stainless steels are the largest volume category of chrome-bearing alloys. Chromium chemicals are used in leather tanning, in pigments, dyes and mordants, printing, chemical process industries, photography, pharmaceuticals, metal plating, pure chromium metal production, and for many other purposes. Chromite is a necessary constituent in basic refractories indispensable for the production of steel, copper, cement, and glass. Under present conditions, the US and North America, with the possible exception of Cuba, have no commercial ore reserves. There are chromite deposits, as will be described, but they would be used only under highly abnormal conditions if all outside sources were cut off for an extended period. All chromite used in the US is imported from the eastern hemisphere in which are contained the principal world reserves. The main suppliers in 1980 were the Republic of South Africa (43%), the USSR (21% ), the Philippines (12%), Albania (11 %), Turkey (8%), and others (5%). The strategic nature of chromite is obvious. End Uses-Grades and Specifications As noted before, the three principal uses for chromite are metallurgical, refractories, and chemical with a fourth minor use as foundry molding sand. For metallurgical applications chrome ore is first reduced in electric carbon arc furnaces to various types of ferrochromium alloys. There are high, medium, and low carbon ferrochromiums with carbon ranging from 0.01 up to 10%. Chromium itself ranges from 50 to 73 %. Ferrosilicon chromium and ferrochromium-silicon grades have chromium from 33 to 67% and silicon from 3 to about 48%. Since iron is reduced with chromium, the Cr:Fe ratio of the ore will determine the ultimate grade of the ferrochromium whereas carbon and silicon can be controlled during processing. MgO, A12O3, CaO, and excess SiO2, are removed in slag. A small amount of pure chromium metal is prepared by alumino-thermic and electrolytic processes from essentially iron-free chrome components that have been made via the chemical route. The higher grades of ferrochromium with chromium in the 66 to 73% range can only be made from ores with not only high chromium content, but low iron, i.e., high Cr:Fe ratio. These ores, conventionally termed metallurgical grade, have Cr2O3 contents of 45 to 56% with Cr: Fe ratios of 2.5 to 4.3. A standard composition is generally 48% Cr2O3 and 3:1 Cr:Fe ratio. Very high grade ores are often blended with lower grades even with the high iron chemical grade. For some ferrochromiums, additions of high alumina refractory grade are used as slag conditioners to facilitate smelting while still contributing chromium values. A lower grade ferrochromium, the high carbon charge chrome, has become the predominant grade in use today for making chromium-bearing steel alloys. This

Jan 1, 1983

By C. G. Dunn, W. W. Martin

Various X ray diffraction techniques have been developed for determining orientations of crystals. Transmission and back-reflection Laue methods1,2,3 in particular have been found to be very useful. In many applications, however, a need still exists for a simplification of the details of analysis so that orientations can be determined more rapidly, and operators with little or no training in crystallography can be easily instructed in the necessary procedures. Filling this need in part is a system of analysis that has been in use for several years in the Metals Section of the Laboratory, General Electric Co., Pittsfield, Mass. This method is an extension of the one of Majima and Togino,4 which uses fifty-five indexed standard transmission Lauemams to cover the entire range of crystal orientations. Greater rapidity in determining the orientation of a crystal is achieved by using a slightly larger set of standard Lauegrams and by systematizing the steps followed. This system of analysis in its present form constitutes the subject matter of the present paper. Although the method uses transmission X ray Laue patterns, many of the operations are applicable to the analysis of back-reflection Lauegrams. Very briefly the method is based on the fact that Bragg and azimuthal angles for two or more identified Laue diffraction spots completely determine the orientation of a crystal, and standard Laue photographs of the Majima and Togino type provide a ready means for identifying Laue spots. After a preliminary analysis, which consists of identifying the pattern in terms of one of the standard patterns, a correctly marked Lauegram is selected to carry out the final analysis. From measured Bragg and azimuthal angles, the normals (poles) of the reflecting planes for the selected Laue spots are located on a stereographic projection and the orient.at.ion of the crystal determined (in terms of the positions of cube poles for example) by a few additional operations on a \I1ulff net. The actual procedure followed will be illustrated in detail after a brief treatment or X ray problems connected with orientation determinations and a discussion of useful principles and techniques. X Ray and Plotting Problems RELATIVE ADVANTAGES OF BACK-REFLECTION AND TRANSMISSION LAUE DIFFRACTION METHODS In the back-reflection Laue method it is easy to make a direct measurement of the tilt of a zone of Laue spots. Specimen thickness also is generally no problem. In the case of thin specimens, however, the time of exposure is less for the transmission Laue method. For example, with silicon ferrite this advantage holds up to a thickness of 0.6 mm if tungsten radiation at 40 kv peak voltage is used. Furthermore, the transmission photograph represents the entire thickness of the crystal whereas the back-reflection picture represents only a surface layer (a thickness of less than 0.05 mm for silicon ferrite), the deeper layers supplying a negligible amount to the diffraction pattern. If a crystal is distorted, the transmission Laue pattern gives more information particularly with regard to the orientation of the crystal and the overall amount of spread in orientation. Finally a 3 1/4 X 4 in. film suffices for transmission photograms; a 4 X 5 in. or 5 X 7 in. film with a central hole is needed for back-reflection patterns Not only is the manipulation of film easier because of the size of film, but

Jan 1, 1950

By Hjalmar W. Johnson

IT has long been accepted that blast-furnace practice varies to some degree with the coke used. While the qualities desirable in iron have been known for some time, the qualities in coke that produce such iron have not been established. There are no objective standards for blast-furnace coke, which is usually described in general terms, as good or bad. Many experienced operators believe that coke cannot be measured objectively except by using it in the furnace, noting the result, and labeling the coke according to furnace operations. This is admittedly unscientific, and besides is useless for the two main purposes for which a measure of coke quality is needed: (I) to produce the best possible coke from the coals and equipment on hand; (2) to test new coals and determine their value for blast-furnace coke. In seeking such an objective measure, much work has been done on tumbler tests, shatter tests, sizes of coke, porosity, specific gravity, reactivity or combustibility and other tests, but as yet very little has been published in which conclusive correlations have been established between such objective measures and furnace operation. In our study of the problem during the past 8 years we have developed no new measures of coke quality, but we have collected data that are presented here in the hope that they may assist in further work, so that at some future time there may be developed such positive measures. The purpose of this paper is to show that there are variations in coke and that such variations do influence the operation of blast furnaces. At the same time we must remember that there are variations in blast-furnace operation and it may be the blast furnace that is at fault. This correlation of coke properties with blast-furnace operation will be worked out in the following steps: I. Discussion of a period when a change in the coke resulted in an increase in efficiency on one furnace and a decrease in efficiency on another. 2. Adaptation of the inefficient furnace to the available coke so that normal efficiency was restored. 3. The use of radial distribution: a discussion of the effect of size of ore layer in adapting blast-furnace operation to the coke. 4. An example of a change in size of coke and the detrimental influence on the production of one furnace. 5. An example of a change in size of coke, together with manufacturing data, to show why it changed, the conclusion being that coke is a product with an optimum value. 6. Illustration of the fact that coke has different optimum values on two furnaces, with discussion on adaptation of operation so the optimum values will be the same. 7. Limitations of the use of screen tests as an objective measure of coke quality. 8. Importance of uniformity in coke. FUNCTIONS OF COKE AND QUALITIES REQUIRED TO PERFORM THESE FUNCTIONS Coke has three important functions in a blast furnace: (I) to furnish most of the

Jan 1, 1941

By Clark L. Corey, Bogdan Lisowsky

Electrical resistivity, X-ray line positions, degree of order, and microstructures have been investigated for Ni-A1 alloys near the Ni3Al composition. The results indicate that Ni3Al undergoes disordering between 1250oC and the mp; also supersaturated y, produced in y + y' alloys by gas quenching, is extensively ordered prior to y' (Ni3Al) phase separation. The latter reaction, if not both, must follow the cooperative phenomena model. Shifts in line position as a function of quench-indulced super satulration are shown. Lattice pavarneters of equilibriunz and nonequilibrium phases are given. THE objective of this investigation was to determine the mechanism and kinetics of the reactions which occur in Ni3A1 and hypostoichiometric Ni3A1 alloys. The results are of particular significance relative to pre-precipitation phenomena. Early work on Ni-A1 binary compositions near the Ni3A1 composition (13.6 wt pct Al) has been adequately reviewed by Hanssen,1 whose phase diagram is presented in Fig. 1. williams2 verified the suggestion made by Taylor and Floyd3 and others4 that y', Ni3A1, may precipitate coherently on (100) planes of the y phase (see Fig. 1 for phase nomenclature); he further suggested a two-step precipitation mechanism consisting initially of probably short-range ordering followed by actual precipitation of y'. The precipitation stage in low-aluminum hypo-eutectic compositions has been studied by a number of investigators;*"7 short-range order or "zone" formation have been suggested as explanations for various diffuse X-ray scattering effects. The ordering reaction in Ni3A1 alloys is characterized by a) a very rapid rate of ordering in nonstoi-chiometric compositions, b) absence of a disordered phase region for the stoichiometric compound, y', or Ni3A1, c) precipitation phenomena as a dominant aspect in hypoeutectic alloys, and d) an increase in elec-trical resistivity on ordering.' The latter two factors were found by Newkirk to characterize ordering in Co-Pt, for which an extensive and detailed analysis was made.' An electrical-resistivity increase on ordering has also been reported for cuAu3.10 PROCEDURE Ni-A1 alloys in the form of 1300-g chill-cast ingots were prepared by vacuum melting electrolytic nickel and high-purity (99.99 pct) aluminum. Very small heats prepared from high-purity carbonyl nickel, supplied through the courtesy of Dr. Goff of the Naval Research Laboratory, were used for comparison with the larger ingots and no differences were noted. The cast material was homogenized in purified argon for a minimum of 72 hr at 1200°C and water-quenched from 1350°C. Compositions studied are given in Table I. The 10 pct A1 alloy was both hot- and cold-rolled. X-ray superlattice line intensities and peak positions were obtained from -270 mesh filings, using CuK, radiation with a LiF crystal monochromat adjusted to receive both 01 and a2. One-degree slits and a 1/8 deg per min scan rate were used to record line traces. A standard tungsten powder, obtained through the courtesy of G.E. Research Laboratory, was used to calibrate line positions.

Jan 1, 1968

PERSONAL (Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during. the period May 10 to June 10, 1915: Robert M. Keeney, Somersville, Conn. C. A. Moffett, Birmingham, Ala. Emilio Mosonyi, San Salvador, C. A: A. W. G. Wilson, Ottawa, Canada. Junjiro Nagazumi, Fukuoka, Japan. G. H. Glover, Jr., Short Hills, N. J. Francis R. Pyne, Elizabeth, N. J. R. W. Brock, Vancouver, B. C. F. C. Alsdorf, Los Angeles, Cal. J. L. W. Birkinbine, Philadelphia, Pa. W. J. Loring, London, England. Roy H. Allen, Jamesburg, N. J. R. A. Bull, Granite City; 111. Francis Andrew Thomson received the degree of Master of Science from the Colorado School of Mines at the recent commencement exercises. The subject of his thesis was Stamp Milling and Cyaniding.

Jan 7, 1915

By T. W. Bossert

MELTING is the initial step in the fabricating of all aluminum and aluminum-alloy products. Its function may be considered as threefold: to improve the metal quality, to adjust the composition, and to change the form to that required for subsequent fabrication. Because the melting operation is generally somewhat removed from the final product fabrication, its importance is frequently overlooked. Melting equipment and melting procedures can reflect materially on fabricating procedures as well as on quality and cost of final product. The selection of equipment and the establishment and control of melting procedures, therefore, should be given careful consideration. It is the purpose of this paper to present the various factors that should be considered in establishing melting procedures and in selecting melting equipment. Certain of these are the result of the inherent characteristics of aluminum and can be treated rather specifically. Others depend on the particular production requirements and hence will have to be considered more generally. This paper is intended to cover only the melting of solids, as differentiated from fines, such as borings, turnings, and sawdust. The melting of fines, in many respects, is a subject that should be treated by itself, and practices for melting fines are by no means as standardized as are those for melting solids. The melting of fines is today the subject of considerable developmental interest; hence practices discussed today may soon be replaced by new or improved ones. CHARACTERISTICS OF THE METAL THAT AFFECT MELTING Aluminum and aluminum alloys possess several inherent characteristics that affect the melting problem. Of the physical properties, density, heat content, thermal conductivity, emissivity, and melting temperatures are important because of their effect on equipment design. A list of such properties for commercially pure aluminum is given in Table r, compared with similar properties for iron and copper. The low density of aluminum as well as of the aluminum alloys is of material advantage in the design of melting equipment, in that such equipment can be considerably lighter than similar equipment for handling the heavier metals. The density, however, particularly of the molten metal, is not greatly different from that of the oxides and other nonmetallic materials that develop or become part of the melt during the melting process. Separation of such nonmetallics is not as rapid a process as with some of the other metals, and consideration of this must be made in establishing melting procedures. Sufficient holding time to permit such materials to separate out and, in some cases, fluxing treatments to aid the separation, are required. Since some of these nonmetallics settle to the bottom of the melt, provision should also be

Jan 1, 1946

By C. G. Dunn

With respect to theories of recrystalliza-tion in metals plastically deformed. it has been said that the present status of this subject is far from satisfactory.1 It may also be said that before any mechanism of recrystallization for metals and alloys can be set forth in a satisfactory manner, there must be made available considerable data on orientation changes that occur during the deformation and recrystallization processes. Although extensive data have been published on recrystallization in single crystals and in poly-crystalline specimens, more results of a type that can be classified according to simple orientation changes would be desirable in this complex field. It might even be said that before classifications are made according to types of orientation changes, it may be possible to classify a considerable amount of data into certain kinds of orientation states if groups of common or nearly common orientation occur. Methods for computing the probability of occurrence for various types of groups have been published2 and it has been pointed out in particular that it should be possible to analyze orientation data for high-order twin relationships between old and new grains even when agreement is not at all exact. In this connection, work on recrystallization in silicon ferrite reported in a paper concerned with complex groups of annealing twins3 indicated that some data were consistent with primary nucleation OCcurring according to a second-order or a third-order twin transformation. However, further work in this latter direction was definitely needed. It is, therefore, the purpose of the present paper to report data and analyses for primary nucleation in silicon ferrite following small deformations that have been carried Out at the Pittsfield Works' Laboratory of the General Electric Co. Analyses have been made with the aid of standard groups of twins that are reported elsewhere.4 PReparation oF Specimens and Experimental Procedure The material used in the present investigation was taken from the same heat of steel as that .used in a prior report.3 The finished strip in both cases was made by the Allegheny-Ludlum Steel Corporation according to methods that produce a high degree of preferred crystal orientation. Samples with large grains had the following composition: 3.45 per cent Si, 0.003 C, 0.008 P, 0.020 S, 0,075 Mn, 0.03I A1 and 0.072 Cu. Thickness of specimens was 0.012 inches. Plastic deformation was produced by cold-rolling the samples on a mill with 8-in. diameter rolls, the plane of the sample in each case coinciding with an XY plane (the plane of projection for the stereo-graphic plots) and the elongation occurring in the X direction. In general, elongations were held to about 3 or 4 per cent.

Jan 1, 1945

By R. A. Greenkorn

This project originated in a practical problem—we needed five tracers that could be used together to locate flow paths in a pilot flood. While tracers for subsurface liquids have been used since the turn of the century,1-15 none of those reported in the literature appeared to be either consistent or quantitative enough for our purposes. Most were used in field systems without controlled experiments to determine the accuracy and precision of analysis, and many were tracers that could not be used collectively. The ideal tracer, of course, would follow the fiuid of interest exactly, traveling at the same velocity as the fluid front. But the ideal is impractical to attain because adsorption-desorption effects cause the tracer to lag behind the front; these effects, plus diffusion-dispersion effects, cause the tracer front to spread more than the fluid front. Thus, our objective was not to locate a tracer that would be ideal for all circumstances but rather, to find one that would approximately follow the fluid, or one that under controlled conditions could be corrected to calculate the movement of the fluid front. We considered tracers satisfactory—(1) if they were easy to analyze; (2) if their breakthrough-elution curves were not too different from those for the chloride ion, a tracer believed to follow the fluid front closely; and (3) if we could calculate from the curves a material balance, at 1.25-PV (pore volume) injected, within 5 per cent of that calculated from chloride curves. Of a possible 35 materials, we selected 13 tracers that could be quickly and easily identified and whose analysis was claimed to be accurate within 5 per cent. Only one of these, tritiated water, was a radioactive tracer. Radioactive tracers are easy to detect even in small quantities, but they require special handling and special equipment. Also, those that can be used together are limited because special equipment is required to separate emissions from the various tracers. Two of the original 13 tracers were eliminated in static tests to determine how accurately and precisely they could be analyzed, and to check on gross adsorption. The remaining 11 were flowed through a 9-ft linear sandstone model, and breakthrough-elution curves were obtained. Finally, three tracers were field-tested as breakthrough tracers. These tests are described in the following sections. The 13 tracers considered in these experiments were EDTA (ethylene diamine tetra acetic acid), fluo-rescein, picric acid, salicylic acid and ammonium, boron (as borate), bromide, dichromate, iodide, nitrate and thiocyanate ions, plus chloride ion and tritiated water. All but the chloride ion and tritiated water were subjected to static sand tests to eliminate the tracers that could not be analyzed quickly and accurately and to eliminate those that showed excessive adsorption. All but two of the tracers, EDTA and salicylic acid, qualified for flow tests on this basis. The procedures used in the static tests (see Appendix A for analytical details) were as follows. Each tracer (in the amount shown in Table 1) was dissolved in 1,000 ml of water. Then, 800 ml of this solution was added to 500 gm of sand, and the remaining 200 ml was reserved as a control standard. The sand-tracer mixture was agitated once a day over a 10-week period, and during this period we analyzed five duplicate samples from this mixture, along with five duplicate samples from the control solution. From the control-sample analyses, we constructed a control chart on which the sand-tracer analysis results were plotted. The control chart, and its use to determine accuracy and precision of analytical results, as well as the amount of adsorption, is described in Appendix B. The results of the static tests are summarized in Table 1, which lists the concentration c (concentration at time t) divided by c, (initial concentration). If there was no adsorption, c/c, = 1. The acceptable deviation from this value varied from tracer to tracer, depending upon the limits of analytical precision established for the different tracers. The best results were obtained with boron, bromide and dichromate, with all values falling within limits of accuracy and precision. Ammonium, iodide, nitrate and picric acid also were satisfactory, although the ammonium results were erratic. Flourescein and thiocyanate were unsatisfactory ini-

By F. W. Metzger

INTRODUCTION Coal quality control in mining and mine planning has always been important and has become even more essential in recent years due to environmental considerations. The primary consumers of the sub-bituminous coals found in the Powder River Basin are electric utilities that require low sulfur coals to meet government air quality regulations. Electric generating plants are designed to burn coal of a specific quality, and the supplier of that coal must be able to guarantee shipments within specified quality tolerances. Over the past several years, Exxon Coal USA and, more recently, The Carter Mining Company, a division of Exxon Coal USA, have established an evaluation and development program to accurately define the geology and quality of their coal properties. This requires an adequate drill hole density so that detailed correlations of the coal seam and the lithologic units, or benches, within the coal seam can be made. These units are recognizable in the core and also on geophysical logs. Like any systematic approach, geologic modeling has been refined and improved through new technologies. Today, coal seam properties are mapped using computer applications. Rapid access and manipulation of these data allow for optimization of mining efforts. This presentation will demonstrate how a detailed mapping program can be important in both pre-mine development and in-pit quality control.

Jan 1, 1983

By M. G. Benz, J. F. Elliott

Otto Schaaber (Institut für Harterei-Technik, Bremen -Schönebeck, Germany)— Langenberg, Pestel, and Honeycutt gave an interesting example of the grain refining effect nonstationary magnetic fields may execute on a solidifying metal. Probably some additional comments, based on more than a decade of experience with this method of influencing crystallization, may be useful. They refer to an attempt to explain the mechanism of grain refinement by such fields, and to recent European developments which have not been mentioned in the paper. I. During studies of the temperature distribution in a metal body near the phase boundary solid/liquid, an anomaly was observed under certain special conditions: a) direction of heat transfer as horizontal as possible, b) steady state (equilibrium, i.e,, solidification resp. melting rate exactly zero). In the liquid phase, immediately adjacent to the phase boundary, the temperature was found to be constant over an appreciable distance in spite of a high value of heat transfer (40.000 to 70.000 keal/ m2h).3 Convection, which might explain this phenomenon, could not be observed. Therefore another explanation had to be sought. The assumption that a metallic melt, especially at temperatures near the point of solidification, contains some sort of atomic arrangement with a higher degree of order than the surrounding liquid, now is generally accepted. Considering the differences in energy between such an arrangement and its environs, a transport of heat even in absence of any temperature gradient is conceivable by continued formation and redissolution of regions with a higher degree of order, i.e., with lower energy level.3 At this stage, it was not necessary to postulate any special condition as to the form or size of these regions or the distance between arrangements to be newly formed and those to be redissolved. However, a simple consideration shows that an energy transfer from one region to another will only be possible without loss of energy, if the distance between will be equal to the lattice parameters, and if, secondly, crystallographic axis or planes will be parallel.4 By the way, this assumption might give a reasonable explanation of the well known orientation effect of the heat flow during solidification. Any measures to prevent columnar crystallization should act upon this ordering mechanism: a) the regions with a lower energy (higher order) should not be allowed to arrange themselves parallel to the direction of heat flow, and their growth should be disturbed; b) all conditions leading to an appreciable heat flow of uniform direction should be avoided or removed. Condition a) may be satisfied by a physical force preferably under 90 deg to the main axis of the columnar crystals (i.e., parallel to the solidification front) acting on the ordered regions; condition b) by equalizing any differences in

Jan 1, 1962

By Richard Akerman

(Translated by FREDERICK PRIME, JR., Professor of Metallurgy in Lafayette College, Easton, Pa.) [THE attention now being paid both in this country and Europe to the greatest economy in the working of the blast furnace, and the eagerness with which all thoughtful men in the iron business look for any new information which will tend to throw light on this sub¬ject, is a quite sufficient excuse for presenting this paper to the Amer¬ican Institute of Mining Engineers.] I. It must be borne in mind that when two bodies unite to form a chemical compound, heat is almost always evolved. In order to

Jan 1, 1873

By Harry A. Lipsitt, Rollins E. Hook, Attwell M. Adair

A necessary condition for a uniaxial stress distribution in compression testing is that the specimen end surfaces make full contact with the apparatus compression plates. In addition all compression surfaces must be machined perpendicularly to the loading axis. In general this condition is not sufficiently fulfilled in a simple apparatus. Therefore on application of the load the compression plate may first touch the specimen at one point only. This may cause crumbling of the specimen if the material under investigation is brittle (e.g., ionic crystals). It also precludes a precise study of the beginning of deformation as the effective cross sectional area is unknown. In addition a complex stress state is set up which renders quantitative work impossible, e.g., on dislocation density and arrangement as a function of stress. To overcome these difficulties a "self-adjusting" upper compression plate is required. A simple and reliable method of achieving this is shown in Fig. 1: A steel hemisphere is placed on the specimen. As soon as the compression plate (which no longer needs precise machining) makes contact with this hemisphere the load is uniformly distributed over the whole specimen surface, and a homogeneous uniaxial state of stress results. An advantage of the method is that the loading is always central, even when the specimen surface is not parallel to the compression plate (Fig. 1, dashed line). Therefore to a first approximation a uniaxial state of stress is maintained if the misorientation of the specimen end surface is small. Two typical stress strain curves of identically prepared sodium chloride crystals are shown in Fig. 2; curve 1 was taken without and curve II with the hemisphere under otherwise identical conditions. The improvement in the accuracy of defining the beginning of elastic and plastic deformation is clearly indicated. The writer wishes to thank the Deutsche Forschungsgemeinschaft for financial support, and Professor P. Haasen for providing facilities for this work.

Jan 1, 1962