Search Documents

By E. DeGolyer

(San Franciso Meeting, September, 1915) I. INTRODUCTION THE Furbero oil field lies in the Gulf coastal plain of Mexico between the important ports of Tampico and Vera Cruz and about one-third of the distance between the two points from the latter (Lat. 20° 22' N., 97° 30' W. Gren.). It is in the State of Vera Cruz, about 14 miles west by south of the village of Papantla in the canton of the same name, and is the most southern of the developed oil fields of the Tampico-Tuxpam region being a distance of 50 miles south by east from the Potrero del Llano field and 42 miles in the sane direction from the Alamo field. The field has been developed by the Oil Fields of Mexico Co. and is in the midst of a large block of lands owned or leased by then. Communication is through the port of Tuxpam with which it is connected by a narrow-gauge railway and 6-in. pipe line some 52 miles in length. This field is of more than ordinary interest since it represents a type of oil deposit hitherto unknown. So far as I am aware, no other commercially valuable deposit of oil is known to occur under conditions of accumulation similar to those found here. The igneous nature of the so-called `sand' encountered in drilling was not recognized until a number of wells had been drilled; and it was not until recently. that the geological relations of the sill or laccolith, which gives rise to the accumulation of oil, were known and the so-called `anticline' was known to be, in part at least, the result of igneous intrusion. Geological surveys in this general region were made in 1900-1901 by W. H. Dalton and in 1907-1909 by P. C. A. Stewart, F. W. Moon, Leonard V. Dalton, and Dr. Max Muhlberg. More recent surveys have been made, however; under the direction of the author, by E. L. Ickes, B. C. Belt, B. Hartley, and Harve Loon-us. Notes of the earlier examinations were not available with the exception of the report by Dr. Muhlberg who apparently first recognized the true nature of the Furbero intrusion. This paper is indebted to his work and that. of the more recent surveys for much of the detail regarding stratigraphy and to Messrs. Percy Furber and Arthur C. Payne, President and General manager of the Oil Fields of Mexico Co. for permission to publish, and for much of the in-

Jan 9, 1915

By C. R. Johnson, R. A. Greenkorn, G. W. Widner

This paper describes a short, simple well-testing procedure evolved from unsteady-state concepts to appraise wellbore damage in water-input wells. Input rates are changed at specific intervals over a 30-minute period and the wellhead pressure recorded at the end of each interval. From these data, the pressure drop due to the "skin" can be computed. This pressure drop in terms of psi/B/D of input rate is referred to as the "skin factor". Two of these variable-rate tests are required to determine change of wellbore damage and to evaluate well-treatment techniques. There are several advantages to the variable-rate procedure. The necessary data can be obtained with wellhead gauges and meters. There is little interference with normal operations. The short testing period eliminates many interpretative difficulties that come from interference from adjacent wells. The shut-in period required for standard tests before the plot of pressure vs log of time attains a straight line is often 12 hours or more. Such a time period is incronvenient, especially when a well must be tested repeatedly to evaluate change in wellbore characteristics. This variable-rate procedure has been successfully npplied to water-input wells in three fields. For some of the wells, skin factors were calculated from both the standard and the variable-rate tests. These results show good agreement. THEORY OF THE VARIABLE-RATE PROCEDURE In many waterflood input wells, the pressure in the wellbore differs from the pressure in the reservoir immediately adjacent to the well because of the restriction of flow through the skin of the well. If the true pressure of the reservoir at the well, p,, is that pressure which would exist in the well if no skin were present, and p,' is the actual pressure as measured in the well, this difference, is the skin effect. Fig. 1 shows the change in skin effect with change in flow rate. As the flow is reduced, the skin effect is reduced by an amount equal to the change in wellbore pressure minus the change in reservoir pressure. The equation of pressure change without skin using the point-source solution of the diffusivity equation is (after van Everdingen')

Occasionally it is interesting, and sometimes useful, to review the past for early references to our industry, and to learn of the trials and travail passed through before it arrived where it now is- and the results of such a review follow. Some time ago one of our modern playwrights and poets, Arthur Guiterman, turned to coal, with the following result: Afar in the Carboniferous time I grew in Paleozoical slime, A lepidodendron with boughs on my stem And lepidostrobuses grew out of them. My roots in the mud of the ages I spread And up to the heavens I vaunted my head, I throve in the heat of tropical sun, And now I am coal at two dollars a ton

Jan 1, 1939

By L. R. Shoenberger

Boron has been used to produce nonaging low-carbon sheet steel. Retention of the necessary minimum amount of about 0.006 pet partially killed the steel. Amounts exceeding about 0.012 pet increased the degree of deoxidotion, piping tendencies, and possibility of hot tearing in primary rolling. Semikilled practice resulted in good ingot yields and satisfactory surface quality. Aluminum added with the boron provided a protective de-oxidizer. Good drawobility was indicated by performances of the steel in a limited number of deep-drawing trials. Some problems with hot-tearing and boron-analysis procedures were overcome. Metal lographically, the boron semikilled steels revealed some structures not usually found in plain low-carbon steels. IN 1943 Low and Gensamer1 reported that strain aging, which hardens and embrittles ordinary low-carbon rimmed steel, was due to nitrogen and carbon, and that oxygen played a relatively unimportant role. Since then, many investigators have substantiated their findings and indicated that nitrogen is particularly potent. Commercially, today's most widely produced non-aging sheet steels for deep drawing are either aluminum killed or vanadium rimmed types. The difference in deoxidation practice, alone, is evidence that oxygen is apparently not an important consideration in control of strain aging. The fact that nitrogen is important is apparent in the consideration that has been given, knowingly or unknowingly, to the amount combined with aluminum and vanadium. Patents were granted to Hayes and Griffis2 for the processing of aluminum-killed steel, and to Epstein" for the manufacture of vanadium rimmed material. Certain prescribed steps in producing these steels can be correlated with the formation of the respective nitrides within certain temperature ranges below the usual hot-finishing temperatures. The potential nonaging properties of either type can be reduced or suppressed by cooling too rapidly to permit the aluminum or vanadium to combine with nitrogen. Subsequent suberitical annealing of the cold-rolled strip, however, normally forms the nitrides and produces the resistance to strain aging. Titanium-killed nonaging steel, described by Comstock,1 forms a nitride in the molten state and is essentially nonaging throughout its processing. Zirconium-killed steel, which was investigated briefly by the author,* appeared to have similar nitride- forming characteristics. It is known" that chromium can produce nonaging rimmed steel, but relatively little is known of the potentialities of some of the other nitride-forming elements such as boron, silicon, columbium, and cerium. In attempting to develop a new nonaging cold-rolled sheet steel with good drawability, the following factors were considered pertinent. Such a steel would necessarily have a low carbon content and therefore have a relatively high degree of oxidation when made in a basic open-hearth furnace. If the denitriding element were also a deoxidizer, a part of the addition would be lost as oxide. The degree of deoxidation would determine whether the steel is rimmed, semikilled or killed, and also could be expected to have an important bearing on ingot yields and ultimate surface quality. Assuming that the pattern for the production of cold-rolled sheets would not be changed to any great extent, the nitride must form in the molten steel, in hot rolling, in subsequent cooling, or in annealing. The nitride, once formed, should resist dissociation and be stable in the final product. Usually an excess of the nitride-forming element is required to combine with sufficient nitrogen. If the element used is a strong ferrite strengthener, a small excess may markedly decrease drawability. With aluminum and vanadium, about 0.03 to 0.05 pct in the steel is preferred. Epstein has said" that about 0.30 pct chromium is required. Titanium nonaging steels are hard unless a sufficient amount (about 0.30 pct) is added also to combine with the carbon. The cost of the necessary amounts of these latter two elements discourages commercial acceptance. Silicon was considered as a possible nitride former, but since amounts up to 0.10 pct in rimmed and semikilled steels do not induce marked resistance to strain aging, larger amounts are apparently required, which would tend to harden and strengthen the ferrite. Of the other elements mentioned, all but boron are expensive heavy-metal elements. Stoichi-ometrically, almost an equal weight of boron would be required to combine with the nitrogen—-ordinarily about 0.003 to 0.006 pct in scrap-practice open-hearth steels. Boron is a slightly stronger deoxidizer than carbon but is less powerful than zirconium, aluminum, or titanium. Thus a rimmed-steel practice might be possible. There is much in the technical literature concerning the hardenability effects of minute amounts of boron in killed steels but very little about its behavior in low-carbon material—particularly as a ferrite strengthener. The available data indicated a need for better information concerning the effects of boron in low-carbon strip steels. Experimental Work Development of a Boron-Treated Nonaging Strip Steel—Initial attempts to produce a boron-rimmed strip steel employed 3-ton basic open-hearth heats which could be teemed into molds large enough to sustain a normal rimming action. Boron as ferro-boron was added to the ladle in small amounts because of the reported hot-short character of aluminum-killed heat-treating grades containing more than about 0.005 pct boron. Actually, the amounts used, i.e., 1/8 and 1/4 lb per ton, would be large for

Jan 1, 1959

By W. Ivanick, Frank W. Glaser

ORDERING reactions of Fe-Si compositions in the a region have been mentioned in a number of review articles.7-8 However, little is known in regard to the critical temperature, T at which this transformation takes place. Greiner and Stoughton,' in a study of the constitution of iron-rich Fe-Si alloys below 800°C, placed the onset of order at a composition of about 4 to 5 wt pct (7.5 to 9.5 atomic pct) Si. They observed that at this composition the ductility and strength begin to decrease sharply and brittleness develops. During X-ray studies they observed only the appearance of superlattice lines for compositions containing 12.5 atomic pct Si. More recent X-ray diffraction studies- etected the appearance of superstructure lines (corresponding to the calculated positions of [Ill] and [ZOO] reflections) for alloys containing 9.5 atomic pct. This fact confirms Greiner and Stoughton's original hypothesis in regard to the onset of order at compositions containing about 7.5 to 9.5 atomic pct Si. The physical properties.of Fe-Si alloys containing more than 10 atomic pct Si have been studied only to a limited extent. Their extreme brittleness and difficulties of sample preparation render them of little industrial use in comparison with alloys in the 0 to 10 atomic pct Si range. The properties of Fe-Si alloys reported to date are mostly properties measured at room temperature on ordered compositions It appears that because of experimental difficulties fully disordered alloys could not be produced in the critical composition ranges and their properties could therefore not be reported. In Figs. la, lb, and lc, a summary of physical properties of Fe-Si alloys, measured during recent investigations of the influence of silicon additions to iron, is presented. No mention of determination of the critical temperature, T for disorder could be found in the literature. The following is an account of work done in an attempt to: 1) produce the disordered state of various Fe-Si alloys and establish the critical temperature, T for disordering, and 2) compare the electrical and thermal conductivity characteristics of the ordered and disordered phases as functions of composition. Materials, Preparation of Test Samples, and Testing Methods Fe-Si alloys with high silicon contents (about 10 atomic pct) are usually prepared using powder metallurgy techniques. This method insures accurate compositions and high purity through the use of protective atmospheres during solid state diffusion alloying of the mixed powders."" Iron and silicon powders were mixed in the desired proportions, cold or hot pressed, and then homogenized at 1150°C for periods ranging from 6 to 12 hr under a protective getter and in a hydrogen atmosphere. Fully homogenized samples were quenched in water from various and successively higher temperatures to establish the critical temperature for disorder. Temperatures were determined using Pt—Pt-Rh thermocouples in contact with the test samples. Test bars were approximately 0.6x1.25x7.5 cm. Electrical measurements were made at room temperature by determining the potential drop over a 1.5 cm span for a current of 10 amp. Densities of the samples were determined by immersion. High temperature electrical resistivities were measured using previously described techniques.'" Specific heat conductivity up to 200°C was measured by heating one end of the test bar and water-cooling the other; heat conductivity was then obtained by subtracting the rate at which heat entered the water from the

Jan 1, 1957

By T. S. Lovering

GEOCHEMICAL prospecting extends the age-old method of searching out lodes with a gold pan and rationalizes the prospector's hunch that certain plants are associated with ore. It uses sensitive but cheap and rapid analytical methods to find the diagnostic chemical variations related to hidden mineral deposits. Exploration geologists can gain tremendous assistance from this new tool, although its optimum use is not simple. To bring out the geochemical pattern that reveals the presence of a hidden ore deposit with a minimum number of samples requires a combination of shrewdness, chemical knowledge, and exploration geology. The use of sensitive analytical methods for prospecting had its start in the 1930's in northern Europe, where Scandinavian and Russian geologists had some success in these early efforts. Very little geochemical prospecting was carried on in the United States at this time, and no sustained interest was manifest until the close of World War 11, when geochemical investigations were started by the Mineral Deposits Branch of the U. S. Geological Survey. The purpose of these investigations was to apply geochemical principles and techniques to surface exploration for mineral deposits. Both the research on analytical methods and the routine trace analyses for field investigations were at first conducted by a single group, but it later became apparent that the trace analyses could be done by men of less experience than that required for successful research on methods. For the past several years there have been two groups of chemists, and although their functions overlap, three of the chemists are chiefly concerned with research, while four to six other men make the trace analyses for field projects. The chemical investigations, as well as the field projects of the Geochemical Exploration Section, concern only those phases of the subject that are appropriate to a government organization; every effort is made to help private industry, but not to compete with it, in finding orebodies. The chief aim of the Section, therefore, is to develop new analytical techniques and publish the results promptly, to carry out field investigations of the fundamental principles of geochemical dispersion, and to field test promising- techniques under controlled conditions. Some routine geochemical exploration work is carried on in connection with DMEA loans, and in district studies where the project chief wishes geochemical information on certain areas for his report. It should be emphasized, however, that geologists of the Geochemical Exploration Section are primarily concerned with fundamental principles underlying the distribution, migration, and concentration of elements in the earth's crust. To facilitate the use of geochemical methods the USGS has published much information on its methods of analysis and has provided opportunities from time to time for qualified professional personnel to study these methods, to work in the USGS laboratory, or to attend demonstrations of the analytical techniques at the Denver Federal Center. Typical of the research carried on are the problems now being investigated: 1) Development of rapid and sensitive analytical methods suitable to the determination of traces of metals and other minor elements in various materials, such as rock, soils, plants, and water. At the present time attention is being concentrated on U, Bi, Cr, and Hg, and satisfactory rapid trace analytical methods are virtually perfected for U and Bi. Good methods are also available for: Cu, Zn, Pb, Ni, Co, As, Sb, W, Mo, Ag, Nb, Ge, V, Ti, Fe, Mn, S, and P. 2) The relation of geochemical anomalies in plant materials to the geochemical distribution of elements in soils surrounding the plant. 3) A study of the dispersion halos in transported sedimentary cover such as glacial drift and alluvium over known orebodies. 4) A study of the behavior of ore metals in the weathering cycle. 5) A study of the behavior of the ore metals during magmatic differentiation. This requires a study of the distribution of minor metals in fresh igneous rocks and their component minerals in a well established differentiation series and in adjacent country rock. 6) A study of the dispersion of metals in primary halos in the wall rock surrounding orebodies. 7) Regional and local studies of the metal content of surface and groundwater in mineralized and barren areas. Many field projects of the Mineral Deposits Branch also require the services of USGS chemists during their investigation of the geochemical environment of ore deposits. From the work that has been done certain general principles have emerged. Concentrations of an element that are above the general or background value of barren material are called positive geochemical anomalies or simply an anomaly, whereas values less than background are called negative anomalies. The anomalies most commonly investigated in geochemical prospecting are those formed at the earth's surface by agents of weathering, erosion, or surficial transportation, but more and more attention is being given to primary anomalies found

Jan 1, 1956

By V. F. Zackay, J. F. Carlson

CURRENT experimental work on the development of gas turbine engines in the automobile industry has emphasized the need for a relatively low cost nonstrategic castable alloy for service in the 1200" to 1400°F temperature range. Ferritic steels

Jan 1, 1956

By J. K. Stanley

IT has been known for many years that the magnetic properties of a ferromagnetic material are very sensitive to internal strain. Any structure-sensitive property such as ferromagnetism, which is a-function of the regularity of the atomic arrangement, and discontinuities such as grain boundaries must show deviations from an equilibrium state when the regularity of the lattice is disturbed. Experience has shown that such distortions have a marked effect on the magnetic properties of a ferromagnetic material. The purpose of this paper is to show the feasibility of using magnetic methods in detecting internal strains. More specifically, it will be shown how such properties as permeability, remanence, and coercive force change on cold- working of aluminum iron and how these magnetic properties change during the annealing below the recrystallization temperatures. This work was conducted for two reasons. One was the desire to see in what manner strains are relieved in aluminum iron at low temperatures-a subject of practical importance in soft magnetic materials-and the other was the feeling that a study of cold-working and strain relief might shed some light honour understanding of what takes place in the deformation of metals DEFINITION IN TERMS It is necessary to define the terminology used in this paper because magnetic nomenclature is usually unfamiliar to the metallurgist, and certain other terms, such as recovery, have been used ambiguously by metallurgists and others. Magnetic terms are best explained by reference to the common hysteresis loop of ferromagnetic materials (Fig. I). In Fig. I the coordinates are magnetic induction, B, (ordinate) and magnetizing force, H, (abscissa). The c.g.s. unit for the magnetic induction is the gauss, the number of flux lines per square centimeter, and the unit for the magnetizing force is the oersted, the number of lines of force per centimeter in air or vacuum. If one starts with a completely de- magnetized specimen and magnetizes it, a typical virgin magnetization curve beginning at the origin is obtained. This curve is also the locus of tips of a family of smaller hysteresis loops. From this curve it is to be noted that the induction is not proportional to the magnetizing force, and that it appears to approach a limiting induction called the saturation value, and does so for values of H of 1000 oersteds. The ratio of the magnetic induction (gauss) to the magnetizing force (oersteds) is called permeability, p. Thus µ = B/H and if the magnetizing force H (oersteds) is specified as 10 or IOO oersteds, the permeability is written as µ10 or µ100. This is the accepted notation, and will be used in this paper. The values of permeability for H = 10 or 100 are chosen as indices for

Jan 1, 1945

By J. K. Stanley

It has been known for many years that the magnetic properties of a ferromagnetic material are very sensitive to internal strain. Any structure-sensitive property such as ferromagnetism, which is a function of the regularity of the atomic arrangement, and discontinuities such as grain boundaries must show deviations from an equilibrium state when the regularity of the lattice is disturbed. Experience has shown that such distortions have a marked effect on the magnetic properties of a ferromagnetic material. The purpose of this paper is to show the feasibility of using magnetic methods in detecting internal strains. More specifically, it will be shown how such properties as permeability, rema-nence, and coercive force change on cold-working of aluminum iron and how these magnetic properties change during the annealing below the recrystallization temperatures. This work was conducted for two reasons. One was the desire to see in what manner strains are relieved in aluminum iron at low temperatures—a subject of practical importance in soft magnetic materials—and the other was the feeling that a study of cold-working and strain relief might shed some light onour understandingof what takes place in the deformation of metals. Definition of Terms It is necessary to define the terminology used in this Paper because magnetic nomenclature is usually unfamiliar to the metallurgist, and certain other terms, such as recovery, have been used ambiguously by metallurgists and others. Magnetic terms are best explained by reference to the common hysteresis loop of ferromagnetic materials (Fig. I). In Fig. 1 the coordinates are magnetic induction, B, (ordinate) and magnetizing force, H. (abscissa). The c.g.s. unit for the magnetic induction is the gauss, the number of flux lines per square centimeter, and the unit for the magnetizing force is the oersted, the number of lines of force per centimeter in air or vacuum. If one starts with a completely demagnetized specimen and magnetizes it, a typical virgin magnetization curve beginning at the origin is obtained. This curve is also the locus of tips of a family of smaller hysteresis loops. From this curve it is to be noted that the induction is not proportional to the magnetizing force, and that it appears to approach a limiting induction called the saturation value, and does so for values of H of 1000 oersteds. The ratio of the magnetic induction (gauss) to the magnetizing force (oersteds) is called permeability, . Thus u= B/H and if the magnetizing force H (oersteds) is specified as ro or 100 oersteds, the permeability is written as or l00 This is the accepted notation, and will be used in this paper. The values of permeability for H = 10 or I00 are chosen as indices for 106

Jan 1, 1945

By David R. Mitchell, E. C. Carris

THE particular field of application of machines utilizing air currents as the primary separating medium is in the cleaning of fine sizes of bituminous coal. Approximately 18,000,000 tons of bituminous coal was cleaned by air machines in 1947, but such machines have not yet been applied in the cleaning of anthracite. This chapter is limited to a description of the processes in which the separation between coal and refuse depends mainly on a difference in specific gravity. Dry processes depending on differences in coefficient of friction, shape, or other property, are described in chapter 17. The possibility of using air for the separation of coal from refuse was recognized early by mining men and many attempts were made to develop commercial machines. Some of these early machines are described by Berrisford,1 Chapman and Mott,2 and Mitchell.3 Only two machines are extensively used today in the United States, the Stump air-flow jig and the American oscillating table. GENERAL CHARACTERISTICS OF AIR CLEANING MACHINES The principles of gravity concentration and the properties of air as a medium for separation were explained in chapter 9. It was pointed out that because of the low density of air a medium of sufficient density has to be built with the material itself. Hence there must be some device to impart to the bed the necessary mobility for proper classification. It was also noted that the compressibility of the air may cause "geysering" of the bed and disturbance of the hindered-settling classification if the correct balance of conditions is not maintained. Most devices use a vertical upward current of air through the bed of material. They differ by the method of imparting mobility to the bed and the method of removing the refuse. In general terms, the air machines can be divided into three types: 1. Pneumatic jigs where the air current is pulsated. 2. Pneumatic tables where the refuse is diverted from the direction of flow of the clean coal by a system of riffles fixed to the deck.

Jan 1, 1950

By D. E. Light, J. Y. Somnay

The use of alkyl acid phosphates and their alkali salts as collectors for the uranium minerals brannerite and uranothorite was investigated. In particular a detailed flotation study was carried out using isooctyl acid phosphate as a promoter. Tests were conducted on an Elliot Lake ore analyzing 0.11% U 3 O 8, chiefly as brannerite, and approximately 9% pyrite. Pyrite was floated with conventional reagents; the flotation of brannerite from the sulfide tails was studied to determine the optimum pH and pulp density to employ with isooctyl phosphate. 4 uranium recovery of over 90% was possible with a selectivity index of 8.95 when these tails were floated at 17% solids and a pH of 1.7. The effect of various modifying agents was also investigated. Aluminum sulfate, lactic acid and sodium silicate improved the selectivity of collection yielding selectivity indices of 9.5 to 11.5. Ferric chloride was found to be a depressant for brannerite. A Bancroft ore which analyzed 0.13% U308, and contained uranothorite was also amenable to flotation using isooctyl acid phosphate. The composite uranium concentrate obtained assayed 0.41% U308 at a recovery of 95.3% and a ratio of concentration of 3.24. Previous investigations1,2 on the flotation of brannerite, pitchblende, uraninite and/or uranothorite from various Canadian ores showed that fatty acids, including oleic acid and tall oils, petroleum sulfo-nates and alkyl acid phosphates, were suitable collectors for these uranium minerals. Additional work carried out by the Mines Branch in Ottawa on brannerite ores from the Elliot Lake area3 used the tall oil Acintol FA-1, or FA-2, as a collector. A recovery of 92% of the uranium in a concentrate which contained about 55% of the weight and assayed 0.2% U3O8 was obtained from a feed of 0.1% U308 in this latter instance. Eigeles et a1.4 carried out flotation on pitchblende ores and found that the most promising results were obtained with alkyl acid phosphates and their alkali salts as collectors. Within the homologous series of alkyl phosphates, the best flotation characteristics were displayed by isooctyl phosphates. Further, isooctyl phosphate derivatives were much less sensitive to hardness forming salts than oleic acid, enabling all flotation tests to be made with tap water. This paper describes tests employing alkyl acid phosphates for the flotation of ores containing brannerite and uranothorite. The flotation work described herein was conducted in conjunction with the development of a leaching process for Elliot Lake, Ontario, brannerite ores. In this process pyrite in the ore was concentrated by flotation and roasted, providing sulfur dioxide which was used to produce sulfuric acid in situ in a liquid-solid extraction process. A 40% conversion to sulfuric acid was indicated at a leaching temperature of 80°C; this resulted in the extraction of 93% of the total uranium after a contact period of 6 hr. A rotary kiln was used as a leaching vessel. Preconcentration by flotation was studied in conjunction with the above process to reduce the bulk of solids for leaching and, consequently, capital expenditure. The materials and methods used in this study will be described initially. Then the results will be presented in two sections, the first dealing with the brannerite ore, and the second with the uranothorite. Finally an economic analysis of the results on the brannerite material will be made. MATERIALS AND METHODS The two ore samples examined were from uranium-producing mines. One was a brannerite ore, a uraniferous quartz pebble conglomerate from the Elliot Lake area, which contained 0.11% U3O8, 4.3% S and 4.5% total Fe. Mineralogical studies of similar samples indicated the presence of quartz, microcline, sericite, pyrite and minor quantities of rutile, pyrrho-tite and zircon. The other ore was from a biotite-rich pegmatite in the Bancroft area; feldspar, quartz and biotite formed the major gangue components. Uranothorite was the principal uranium mineral; the head assay was 0.13% U 3 O 8. Preparation of Feed: The ores were crushed to —10

Jan 1, 1963

By Francois E. Heuze

Today, the favored option for disposal of high-level nuclear wastes is their burial in mined caverns. As an alternative, the concept of deep disposal by rock melting (DRM) also has received some attention. DRM entails the injection of waste, in a cavity or borehole, 2 to 3 kilometers down in the earth crust. Granitic rocks are the prime candidate medium. The high thermal loading initially will melt the rock surrounding the waste. Following resolidification, a rock/waste matrix is formed, which should provide isolation for many years. The complex thermal, mechanical, and hydraulic aspects of DRM can be studied best by means of numerical models. The models must accommo¬date the coupling of the physical processes involved, and the temper¬ature dependency of the granite properties, some of which are subject to abrupt discontinuities, during [a]- ß phase transition and melting. This paper outlines a strategy for such complex modeling.

Jan 1, 1982

Jan 1, 1911

By M. S. Seltzer

High temperature steady-state creep rates have been determined jor lead sulfide single crystals whose defect concentrations were fixed by equilibration under controlled sulfur pressure. The activation energy of creep, Qc , for undoped lead sulfide, is a function 01 composilion, decreasing from 2.9 to 2.2 ev as the carrier concentration increases from 9 x 1016 to 8 1018 electrons cm-3 for lead excess crystals, and increasing from 1.7 to 2.3 ev as the concentration of holes increases from 4 x 1017 to 1 x 1018 cm-3 in sulfur excess material. For five different composilions, Qc for undoped and bismuth-doped crystals has been found to be equal to Qpb + Qs, the self-diffusion activation energies for lead and sulfur in PbS. It is well-established1 that high-temperature steady-state creep of pure metals is a diffusion-controlled process, where the activation energy of creep is equal, within experimental error, to the activation energy of self-diffusion. The relationship between the activation energy for steady-state creep and those for self-diffusion in binary compounds is more complicated, however, because two different diffusing species must be considered, and becayse the activation energies may be influenced by compositional variations and by foreign atom additions.2-4 In some cases experimentally determined creep activation energies are correlated with those for self-diffusion of the slower-moving species, but such agreement is by no means universal. Interpretation of experimental results is difficult because few investigations include measurements of creep rates and self-diffusion coefficients of both diffusing species on single crystals of similar composition and foreign atom concentration. The objective of this investigation, therefore, is to determine the influence of stoichiometric defects and foreign atoms on steady-state creep and self-diffusion for a well-characterized binary compound. Lead sulfide, a compound semiconductor which crystallizes in the NaC1-type structure, and whose homogeneity range includes compositions on either side of the 1:l atom ratio, was chosen for study in this investigation. The pressure-temperature-composition relations for PbS are available,5,3 and deviations from stoichiometry may be monitored by electrical measurements.7 Single-crystal specimens are available to allow observation of effects due to bulk phenomena without interference from grain-boundary effects. These crystals have been employed to determine steady-state creep rates under compressive stress for "pure" and bismuth-doped PbS as a function of sulfur pressure and temperature as well as crystal orientation and applied stress in order to establish the relationships between defect concentrations and creep rates. EXPERIMENTAL PROCEDURES Crystal Growth. Lead sulfide crystals, prepared by the Bridgman method, are grown in evacuated quartz crucibles, filled with almost equal atomic proportions of high-purity (99.999 pct) lead and sulfur, and heated to a temperature above the melting point of PbS (about 1127°C) so that the lead and sulfur react to form molten PbS. The crucible and melt are dropped through the hot zone of the crystal-growing furnace at the rate of 1 cm per hr. The maximum melting point of PbS is slightly on the lead-rich side of the 50:50 composition; hence crystals grown from a near stoichiometric melt are usually n-type semiconductors containing excess lead atoms. Typically the lead excess concentration in solid solution with the PbS is 3 x 1018 atoms cm-3. Crystals containing either 1/20 or 1/2 mole pct Bi2S3 were prepared by addition of the foreign atoms prior to crystal synthesis. Preparation of Specimens of Controlled Stoichiom-etry. Since it is difficult to grow crystals of desired composition, the process of crystal growth and control of stoichiometry are separated into two distinct operations. Equilibration of as-grown PbS to a desired composition is most easily accomplished by first annealing the n-type crystals under high sulfur pressure (about 1 atm) at temperatures above 700°C. This process serves to put excess lead precipitates into solution, yielding 0 -type crystals upon quenching to room temperature. Inter diffusion occurs readily in crystals so treated, and the methods described by Bloem may then be employed to obtain crystals of controlled stoi-chiometry. For the creep measurements made in this study, this involves heating crystals in mixtures of H2 and H2S The equilibrium constant for H2S is given by: Thus the sulfur partial pressure is obtained from knowledge of the H2/H2S ratio and Kh2S for the temperature in question. Fig. 1 shows the p-T-x diagram for PbS. It can be seen that, within the stability limits for single-phase lead sulfide, desired compositions may be obtained by equilibrating under a specified sulfur pressure and temperature. Characterization of Crystals. The principal methods for evaluating PbS crystals include measurement of electrical properties and mass-spectrographic analysis. The measured electrical parameters include Hall coefficient, conductivity type, and electrical resistivity Bloem7 has shown that there is a 1:l relation between the defect concentration and carrier concentration obtained. Hence, if the contribution to the carrier con-

Jan 1, 1968

By J. D. Exner

With the introduction of rotary drilling in the Gulf Coast area, some thirty-two years ago, and its subsequent spread to other producing localities in the United States, there has been a constant change in the design of equipment. Only the general features remain, namely the rotating drill stem and the circulating mud. Only recently have the properties of mud and their behavior received attention from petroleum engineers, but circulating problems in present deep drilling demand further study and understanding. It is the purpose of this investigation to determine the relative changes in the apparent viscosity of muds with changes in temperature and to discover other physical effects due to heat. Very little information has been published regarding the effects of temperature on the viscosity of drilling muds. Maustl states: "The viscosity of most muds is decreased on heating, but the interesting thing is that the degree of flocculation is also increased on heating. There will be a greater tendency to seal off formations at high temperatures than at low temperatures." With regard to the effect of temperature on viscosity and yield point, Herrick2 states: "The variation of yield point and viscosity of mud with temperature.....is not very clearly brought out by the data available. Both appear to decrease slightly with increasing temperature up to 200' F." The experimental results presented in this paper further emphasize this point. Two types of viscosimeters are available for measuring the apparent viscosities of drilling muds: the efflux tube type as used by Herrick3 and Marsh, and the torsional type such as the McMichael or the Stormer viscosimeters. Because of its extensive use in measuring the apparent

Jan 1, 1933

By I. J. Corrans

Wet high-intensity magnetic separation (WHIMS) has been successfully applied to the recovery of gold and uranium from the residues of Witwatersrand ores. Good overall recoveries have been achieved for particles as small as 12µ, and finer particles of uranium minerals are recovered when present as inclusions. The best results were obtained with a matrix of soft-iron balls 6 mm in diameter. However, pilot-plant tests drew attention to a major defect of the machine: the matrix could be blocked by wood chips and ferromagnetic particles. This problem was overcome by the incorporation of a modification that allows the balls to be discharged from the rotating annulus. Two full-scale units that incorporate the modification have been installed.

Jan 1, 1980

By P. H. Dudley

The piping and segregation of ingots of steel is a comprehensive subject, and must be studied in reference to the different grades of soft, medium, and hard steel, rather than to discuss it in a general manner, as though applicable to all grades. Rail steel, however, will receive the most consideration in this paper, for the wheel-loads of the motive power and rolling stock have doubled from 1890 to 1910. Steel rails and tires which were efficient under the light loads, became less serviceable under the double wheel-loads, quadrupled tonnage, and higher speeds. Bessemer Steel. Bessemer steel of from 0.10 to 0.15 per cent. of carbon, for splice-bars, spikes, and tie-plates, rises in setting, and is cast in bottle-mouthed molds, which must be capped to prevent an overflow from the top. This grade of steel rises in the molds and makes a longer ingot than the volume of molten steel when first teemed. The ingots which are allowed to cool and then cut open, show, particularly in the upper part, large occluded blow-holes, and when they are not oxidized or do not contain foreign matter, weld more or less completely when the steel is rolled or forged above 1,100° C., and it is in this way that the blow-holes are closed in the low-carbon steels. Boiler-Plate and Fire-Box Steel. These grades often contain more or less minute laminations, which are the remains of small blow-holes forming after the setting metal has reached a pasty condition. The blow-holes in the low-carbon steels have not been prevented by usiug deox-idizers, though the ingots are slightly improved so far as the soundness of the steel is concerned. This grade of steel also rises in the molds in setting.

Jan 1, 1914

The Library belonging to the Institute is now administered as part of that of the United Engineering Society, the members of the Library Committee representing the Institute on the Library Board of the United Engineering Society. The main collection now consists of 115,900 books, 3680 pamphlets, 5811 maps, and 4402 searches, making a total of 129,793, a net gain of 7701 within the year. There is in addition a lending collection of 1004 volumes and one of duplicates amounting to 11,310. The library grows steadily both by gift and purchase. The cataloging is now substantially current covering 124,100 items represented by 362,145 cards. There are many rare and notable books, especially those relating to early engineering. It is truly a great treasure house of knowledge. While no severe effort is made to record all visitors the books showed 23,470 to have used the Library in 1928. In addition 5102 telephone requests for information were answered, 202 searches and 196 translations made and 34,964 photo prints furnished. The service department is maintained by small fees which cover the cost. The total amount appropriated for operating expense for the year was $46,300, of which $8,240.02 was furnished by the Institute, $5,399.45 being derived as income from the Douglas Library Fund and the remainder from current receipts. Within the year a slight change was made in the method of meeting the expenses of the Library, a flat charge of $5,000 per year being made against each of the four Founder Societies and this being supplemented by a surcharge based upon membership. The effect of this has been for the present to decrease slightly the amount that the Institute would otherwise need to pay. Placing in one collection all the books of the four societies greatly increases the number of books accessible to the members of each and opening the Library to the public is an important factor in keeping the tax exemption privilege enjoyed for the building. The Director and Staff of the Library make every effort not only to accommodate those who come in person to consult the collection but members resident elsewhere who communicate by letter or wire. The facilities of the Library are truly available to all.

Jan 1, 1929

By Louis Raymond, John E. Dorn

The object of this investigation was to analyze the recovery that arises when the stress on a specimen undertaking creep is reduced. For this purpose annealed specimens of high-purity aluminum were precrept under a stress of 1000 bsi to a strain of 0.08 following which the stress was reduced for various periods of time to 10, 250, 500, or 700 psi. When the original stress was reapplied the subsequent creep curve lay above that for the unre-covered state and below that for the original annealed state. Analyses on the kinetics of this recovery as a function of the temperature gave a stress-sensitive activation energy that decreased as the reduced stress was increased from a value of 64,000 cal per mole at 10 psi to 37,000 cal per mole at 750 psi. Recovery was also detected and measured during creep under the reduced stress. Following a short initial period, the creep rate under the reduced stress increased monotonically until it reached the secondary-creep rate for the reduced stress. The temperature dependence of this phenomenon was also shown to be correlatable in terms of the previously deduced activation energy for recovery. The activation energies for creep of most pure metals at high temperatures have been shown to agree well with those for self-diffusion.'j2 Since the true secondary stage of creep is usually due to the steady-state balance between the rate of strain hardening and the rate of recovery, it is generally thought that the activation energy for recovery of the creep-induced substructure equals that for creep itself. A shoft time ago, however, Ludemann, Shepard, and Dorn~ found that the activation energy for recovery of the creep-induced substructure in high-purity aluminum under zero stress was almost twice that for self-diffusion, namely about 65,000 cal per mole; obviously recovery under reduced stresses differs in some significant way from the recovery that accompanies the secondary stage of creep. The major purpose of this investigation is to study the effect of stress on the re- covery of the creep-induced substructure in order to provide a better understanding of the recovery mechanism itself. EXPERIMENTAL TECHNIQUE High purity aluminum, containing 0.004 pct Cu, 0.002 pct Fe, and 0.001 pct Si, used in this investigation, was in the form of 0.100-in.-thick sheet which has been cold-rolled to the H-18 temper. Creep specimens were milled from the sheet with their tensile axes in the rolling direction. All specimens were then heated at 686°K for 1 hr followed by air cooling in order to produce an annealed structure which exhibited a uniform equiaxed grain size of about 4 grains per mm. Tests were run in creep machines fitted with Andrade-Chalmers type of lever arms so contoured as to maintain the stress constant to within 0.05 pct of the reported values. Constant temperatures to *O.l°K were obtained by complete immersion of each specimen in a temperature-controlled and agitated bath of molten KN02-KNOs mixture. Where changes in temperature were involved, the change was effected in less than 2 min by manually replacing one bath by another controlled at the second temperature. Displacements over the gage section were sensed by linear differential transformers, the output of which was autographically recorded. The calculated strain measurements were sensitive to 5x EXPERIMENTAL PROCEDURE The following analyses are based on extensions of the previously announced effect of the temperature on the creep strain,2 namely for a = constant, where e = the total true tensile creep strain for a given applied true tensile stress, t = the duration of the test, R = the gas constant, T = the absolute temperature, Q, = the activation energy per mole for creep which is independent of the stress, / = a function of 8, = and of the stress, and a = the stress. The validity of this correlation for high-purity aluminum is demonstrated in Fig. 1 for temperatures in the near vicinity of 600°K; the activation energy for creep, Q,, which is approximately that for self-diffusion, is insensitive to the applied stress

Jan 1, 1964

By Henry M. Howe

If a bar of wrought iron or steel is suddenly cooled from a bright red-heat, the contraction which then occurs is considerably greater than the expansion previously caused by heating the bar, so that its final length is considerably less than its initial length. Mr. Thomas Wrightson has investigated this phenomenon,* and has shown that not only does this permanent contraction occur on sudden cooling, but, if the heating and cooling be repeated, say fifty times, a further permanent contraction occurs at each successive cooling. In Mr. Wrightson's opinion, this contraction cannot be explained on mechanical grounds, and he ascribes it to some molecular change caused by sudden cooling; but I think that we need not invoke mysterious molecular changes to explain this phenomenon, which appears to me to be due to very simple and purely mechanical action. Let us consider the cooling as divided into two periods, in the first of which the exterior or skin of the bar becomes almost completely cooled, and hence tends to contract almost to its initial dimensions, while the still hot arid plastic interior contracts but little; in the second period the already cool skin remains nearly constant in temperature, and hence tends to contract but little, while the interior cools from a comparatively high temperature to the ordinary temperature, and hence undergoes great contraction. The excess of the contraction of the skin over that of the interior during the first period tends to make the bar bulge in the middle of its length. This, as well as the decrease of density which occurs, Mr. Wrightson correctly explains. The interior of the bar just sufficed to fill the skin when both were in their initial condition, before being heated at all. At the end of the first period, the volume of the still hot interior is more than the now contracted skin can hold while maintaining its initial shape; and the effect is much the same as when we powerfully blom into a soft India-rubher Lag of the shape of the skin of the bar—it bulges, and tends to approach the spherical shape, in which the ratio of surface to

Jan 1, 1886