Search Documents

By H. J. Hager, P. H. Haskell

Fox the past 20 years Alabama has probably led all other coal-producing districts in the proportion of coal prepared by wet washing. All rail mines, with one exception, and a high percentage of truck mines now wash all coal under 3 or 4 in. Most of this coal has been cleaned by jigs, though within the past few years one or more wettable plants have been installed for cleaning some of the coal from practically all the major seams. These tables supplement either single or multicell jigs usually for one of the following purposes: (I) to wash the finer sizes of raw coal, (2) to rewash the finer sizes of washed coal after they leave the jigs, (3) to retreat jig middling products. The main purpose of this paper is to present cleaning data and operating factors involved in the preparation by tables of the finer sizes of raw coal. The specific information and data pertain to the Mary Lee seam of coal as extracted at three of the mines of the Alabama By-Products Corporation, which produces coal for both by-product coke-oven consumption and the general steam market. The Mary Lee seam has long been recognized by coal-preparation authorities as presenting a very difficult ash-reduction problem. Washing characteristics and physical structure of the seam vary widely. Its thickness ranges from 32 in. with no rock parting to l00 in. with from one to three partings. Over the entire field the bed contains bands of bone and rash. These are distributed throughout the seam cross section. A portion of this bone or bony coal occurs as definite bands 1 in. or more thick; however, some bone is interlocked as layers within the coal and consequently breaks into flakes when the coal is broken. This material is relatively high in ash and its specific gravity varies widely. It has been observed that in most cases in the washing of Mary Lee coal from 10 to 18 per cent of the raw coal is within ±0.10 specific gravity of the attempted point of separation. Therefore with the average wet jig, only with extreme difficulty can a low-ash product be obtained without loss of much marketable coal in the refuse. Without entering into the controversial question as to whether modern washing equipment can efficiently handle simultaneously all sizes up to a given maximum, suffice it to state that the comparatively old-type jigs in service at the Alabama By-Products Corporation's mines could not clean the fine sizes satisfactorily. Therefore, in 1931 that company installed six diagonal-deck tables at the Barney mine, which were installed as an addition to a complete plant cleaning all coal below minus 3 in. The primary washed product is shipped as steam coal and another portion may be prepared as washed nut for domestic trade. These tables are washing 9 tons per hour of raw coal sized to ¼ in. to 0. The washed table coal is mixed with the 3 to ¼ -in. jig product to constitute a 3 in. to o steam coal.

Jan 1, 1941

By W. P. Heineken, A. T. Child

This paper presents the results of a series of experiments made in the metallurgical laboratory of Columbia University, New Pork City. The object of the investigation was to determine, as far as possible, the changes in micro-structure and physical properties caused by short periods of heat-treatment and the longer malleable cast-iron process. It was proposed to do this by means of micro-photographs, heating- and cooling-curves, and tensile tests after the various heat-treatments. I. Micro-Constituents of Iron and Steel. The list of the micro-constituents of iron and steel has grown till now it includes seven different substances, called ferrite, cementite, pearlite,* martensite, austenite, sorbite and troosite. Only the first five of these are mentioned in this paper, to facilitate the understanding of which, the following brief definitions are given: 1. Ferrite (named by Prof. Howe) is, chemically, iron free from carbon. It is the softest of the constituents, and is not colored by etching, except when long-continued. Under the microscope it is easily determined by its regular polygonal etructure; or, if structureless, as in malleable cast-iron, by the ease with which it is scratched. Ferrite appears in mild steel in small amount, in grey cast-iron, and in malleable cast-iron. 2. Cementite (also named by Prof. Howe) is now generally conceded to have the formula Fe3C. It is the hardest of the micro-constituents, having the hardness indicated by 7 of the mineralogical scale; and hence it is always left in relief after

Jan 1, 1901

By A. J. Chellew, Robert Condit

THE Company maintains a port agency at Antofagasta for dispatching copper and also for receiving from ocean vessels the vast variety of materials and supplies required at the plant. Copper shipments from the oxide plant refinery to Antofagasta amounted to 162,000 metric tons during 1951, while incoming freight totalled 175,000 metric tons. Electrolytic market copper in various shapes is currently loaded at the plant upon 20 or 30-ton cars of the meter-gage Antofagasta-Bolivia Railroad, to be transported a distance of 165 miles to the company's yard at Antofagasta. Here it is unloaded by cranes at the rate of about 175 tons per hr. Copper not scheduled for immediate shipment is stocked in tiers within the yard, but most of it is reloaded and sent to port works or a wharf serving lighters. Some of the vessels entering Antofagasta tie up at the port works, while others anchor inside the breakwater. In the latter case, all of the loading into the hatches is from 50-ton lighters towed to the vessel. When the vessel is at the dock, about half of the copper is loaded by port works cranes and the other half is loaded by ship's tackle from lighters. Fuel Oil Requirement Expands One of the innovations caused by the construction of the sulphide plant has been the necessity to provide facilities at Antofagasta for receiving and storing greater quantities of fuel oil than in recent years. From here it is loaded into tank cars for transportation to Chuquicamata. The older installation consisted of a 10-in. submarine pipe line, heating, and pumping facilities, a 67,500-bbl storage tank, and railroad loading rack, located at Antofagasta's northern limits. Two new tanks, of 80,000 and 30,000-bbl capacity respectively, have now been added and a second submarine pipe line will shortly be installed. Fuel oil requirements for the sulphide plant are estimated at 39,000 bbl per month, in addition to which 9000 bbl per month are required for the operation of the oxide plant. The company has a special lighter which is used by its diver for connecting the oil line with the oil tanker when disembarking oil, this lighter also being used for inspecting and overhauling buoys, as well as for recovery of bars of copper which are sometimes dropped into the bay when loading vessels during periods of rough weather. Transport of oil to Chuquicamata is by 76 tank cars of, 20-ton capacity and 20 of 30-ton capacity, all assigned to the company's fuel oil shipments excepting six for Diesel oil and one for gasoline. Incoming Freight Other freight received by the port agency has been averaging about 4800 metric tons per month of operating supplies for the oxide plant (renewals of equipment, spare parts, lubricating oils, and greases, etc.), some 1900 metric tons per month for the company stores, and about 6000 metric tons per month of materials and equipment for the construction of the sulphide plant. The greater part of these shipments (particularly the operating and construction supplies) originate from abroad, and must be handled through the Chilean Customs. Hence the company maintains a Customs storage warehouse (goods pending appraisal of Customs duties) in addition to its other storage facilities at Antofagasta. Not the least of the Port Agency's duties is to meet air and steamer passengers en route to Chuquicamata and to arrange for their trips up the hill. Landing in a strange country with a strange language, the first impressions of a new employee might otherwise be indeed confusing when facing Antofagasta's unique setting of brown barren hills.

Jan 1, 1952

By E. H. Timmerman, A. F. van Everdingen, J. J. McMahon

The prevent paper contains a method which combines the material balance equation' with the water influx equation' to obtain reliable values for the active oil originally in place and a quantitative evaluation of the cumulative water influx. The method is illustrated by an application to a reservoir without original gas cap. In the absence of an original gas cap. results may be obtained using only field production and pressure data, PVT analyses. and a minimum of subsurface information. CHARACTERISTICS OF RESERVOIR AND RESERVOIR FLUIDS Production in the field under review is obtained from the top of the Wilcox formation of Eocene age, at a depth of approximately 8,100 ft subsea. The structural map, Fig. 1, shows that the accumulation, half elliptical in shape with the long axis in east-west direction, is trapped to the north and on the upthrown side of a normal fault. A number of east-west faults with additional minor faulting in random directions are found in the general area, and seismic information and production performance indicate in this particular case the existence of a second fault a short distance downdip, with a strike more or less parallel to the fault controlling the accumulation. It is estimated that 1,830 acres were originally underlain by oil and that the maximum thickness of the original oil column, about 37 ft, was only slightly greater than the maximum thickness of the oil-bearing sand. Maximum net sand thickness was estimated at approximately 26 ft. From logging and subsurface information the gross sand volume has been placed at 37.400 acre-ft. which reduces to about 27,500 acre-ft after probable non-productive intervals have been deducted. The following table presents laboratory analyse; data for the Wilcox sand cores. Average Average Samples Considered Permeability Porosity All Samples 236 md ..19.9percent Samples with k>l md 256 md 20.5 per cent Samples with k>8 md 275 md 20.9 per cent Interstitial water was estimated at 15 per cent. The initial gas-oil ratio was approximately 900 cu ft/bbl. and the initial shrinkage factor was determined by the laboratory to

Jan 1, 1953

By Louis B. Slichter

Prospecting is certainly the world's biggest and best gambling business. It is a game where the chips cost many thousands and where many millions, even billions, can be won. An attractive feature of this gamble is the fact that the players are free to rig the odds as favorably as possible. Only the limited bounty of nature, the restrictions of the laws of the land, the competition from other players, the limited sagacity of the player himself- only these, and other factors, restrict the possibilities for large winnings. Today probably about half the land surface of the earth remains to be searched for signs of ore visible at the surface. It is fortunate that so much land still remains for exploration by relatively economical methods. Looking to the future, it is a good guess that the costs of finding ore will increase in response to increasing technical difficulties. To continue to achieve profits from prospecting, it will become necessary to analyze the business more skillfully, in a more and more sophisticated manner. Whenever feasible, qualitative concepts must be replaced by their quantitative equivalents, improvements, and extensions.

Jan 6, 1960

By H. LeChatelier, B. Bogitch

Page Introduction........................... 134 Methods of Investigation....................... 135 The Tridymite Network...................... 137 Independent Variables....................... 146 Manufacturing Operations..................... 153 Introduction Silica brick are indispensable in the manufacture of steel because they alone are able to withstand the high temperature of regenerative furnaces. All attempts to replace silica brick by other refractory materials for this purpose have failed, but the reason for this failure has remained obscure; we shall give an explanation later in this paper. Before the war, silica brick employed in France came principally from abroad, for which reason, since the beginning of hostilities, certain French steel works have been seriously handicapped. Our attention was first directed to the question by M. Bied, Engineer of the Teil Works. With him, we began certain investigations, at first using our laboratory and the furnaces of neighboring steel works. The larger part of our experiments, however, have been made in the laboratory of the Faculty of Sciences at the Sorbonne. For the heating of our samples, we are deeply obliged to MM. Charpy, Yeatmann and Guerineau. In undertaking these studies, our first aim has been to render assistance to French industry, by indicating, as precisely as possible, the necessary conditions for the manufacture of high-grade brick; but at the same time me have

Jan 1, 1919

By R. D. Reiswig, J. M. Dickinson

The 0s-Ir equilibrium diagram was determined. The diagram is of the simple peritectic type, with a peritectic temperature of about 2660°C. The solid miscibility gap is narrower than previously reported, the nearly vertical solvus lines occurring at about 42 and 63 wt pct 0s. Widmanstaetten figures resembling martensite in some of the two-phase alloys account for a previously suspected transformation. In view of the long history of use of such alloys, it is surprising that the 0s-Ir equilibrium diagram has not yet been completely determined. The boundaries of the miscibility gap in this system have been estimated to be between 24 and 39 wt pct 0s and 79 and 100 wt pct OS. It has been predicted3 that alloys of ruthenium, osmium, and rhenium with the fcc platinum metals should solidify peritectically in their two-phase regions. The metallographic examination of natural osmiridium alloys has been said4 to indicate, by the presence of a martensitic structure, the existence of a transformation or a phase separation. On the basis of superconducting transition temperature measurements, a 70 at. pct 0s alloy was found5 to be two-phase prior to annealing. EXPERIMENTAL The elemental components used in this work were obtained from several suppliers as sponge. The purities, stated by each supplier to be in excess of 99.8 pct, were confirmed in each case by a semiquantitative spectrographic analysis. The pure components were premelted in an inert-gas tungsten arc furnace with the evolution of some fume, crushed, and pickled for use as alloy melting stock. Upon arc melting to the final compositions, no fume evolution was observed. Because weight losses of the order of 15 mg or less were observed in preparing alloy buttons weighing 15 g, "synthetic analyses" were used in determining the compositions of the alloys. Alloys used in this investigation contained 15, 20, 33, 40, 42, 43, 45, 50, 55, 60, 63, 64, 66, 70, 79, and 80 wt pct 0s. Heat treatments of the alloy buttons and pieces thereof were performed in a previously described6 tungsten tube furnace under pressures of 105 torr or less. It was found that homogenization treatments on the specimens were essential to remove the severe coring which was present, a 3-hr treatment above 2300°C removing all the metallographi-cally visible evidence of coring. Following the various heat treatments, the specimens were "vacuum-quenched" by melting a tungsten fuse wire and allowing them to drop onto a water-cooled copper plate. In a few instances, specimens were quenched into molten tin for comparison, but no difference was apparent. Vacuum-quenched specimens cooled from 2400°C to below a red heat in less than 60 sec. Typical equilibration times varied from 3 hr above 2300°C to 88 hr near 1100°C. The utilization of successively longer equilibration times and the approach to equilibrium from both directions indicated that the times used were sufficient to give a close approach to true equilibrium. Heat-treatment temperatures were measured with a calibrated Leeds and Northrup optical pyrometer through a 0.120-in. lateral sight hole in the tungsten heater tube. It was known that the assumption of black-body conditions inside the 1-in.-diam by 10-in.-long tube was unwarranted. The empirical results of work with thermocouples and melting

Jan 1, 1964

By Scott Turner

IT has been considered that the training of an engineer is too often vocational training; that it is a pity all engineers cannot have had a period of liberal training before taking up' pure engineering. Offhand, the so-called liberal courses should bring more ready adaptability to deal with the unexpected, to face with assurance situations which have had no parallel in one's experience, and to move without hesitation under conditions which were heretofore unknown to one, than the specialized course in mining engineering. We hear increasing talk as to the necessity of making the engineer articulate and bringing him into public life. The social implications, and responsibilities of engineering are pointed out, as of equal importance with the prodigious marvels of engineering ingenuity. You often read of this as the logical result of the in¬creasing consciousness of the engineer as to his rela¬tive position in our modern industrial civilization. , Some wag has noted that man is the noblest work of God, but that man is the only one who has said so. Perhaps engineers are the only claimants as to the necessity of their going in for public life and service; at any rate, some liberal educators' still maintain that a well-rounded general education is the better training.

Jan 1, 1930

By J. J. Bodmer

The four different modes, more or less practiced for subdividing slag (that is, producing slag sand), are the following: 1. Crushing the slag from the lump in Blake's crusher, by edge runners or other suitable means. 2. Blowing water, steam, cold or hot air, into the stream of viscous slag whilst it runs from the furnace. So treated, the slag takes

By Harry C. Swanson

TRANSPORTING concrete from mixer to forms has always been a problem. Twenty-five years ago this task was generally accomplished by means of wheelbarrow or concrete buggy. On large dam jobs, as the number of these projects increased, the gantry crane or highline came into use. Today several methods of handling concrete are employed on smaller surface construction jobs, for example, transit-mix trucks or dumpcrete trucks, which have crawler cranes with buckets for placing concrete into forms. In 1944, during early stages of developing Mather mine A shaft, several large underground concrete jobs were necessary. At this time the Cleveland-Cliffs Iron Co, purchased the first pump-crete machine, introduced by the Chain Belt Co. of Milwaukee. The machine was used to pour approximately 200 cu yd of concrete for a dam, or bulkhead, located 400 ft from the shaft. Concrete was mixed on surface, lowered down the shaft 1000 ft in a 2-cu yd bucket hung under one skip, spouted into the bowl of the pumpcrete machine from the bucket, and pumped directly into the forms. Since the day of the first pipeline concrete in 1944 to the present time, other equipment and other methods have been developed to permit transportation of concrete by pipeline through vertical and horizontal distances totaling 1 mile from mixer to forms. Much of the efficiency in present handling of underground concrete can be credited to the Bethlehem Cornwall mines, where concrete was transported through 6-in. pipe for great distances down an inclined shaft and along levels into forms.' During initial development of Mather mine B shaft, with concrete work under way on two or more levels at one time, the pneumatic concrete placer, Fig. 1, was selected as best adapted for underground concrete transportation. The 3/4-cu yd pneumatic placer is a small machine readily moved from one location in the mine to another. It can be equipped with two sets of mine car wheels, which will permit moving on regular mine tracks. It is therefore possible to send concrete through the pipe at great velocity; the pipeline is clean after each shot except for the film of cement adhering to the inside. With the proper slump in the concrete, it is possible to shoot concrete 2000 ft with this machine, using the mine supply of compressed air at 95 psi. This equipment was first used at Mather mine B shaft to concrete slusher drifts, Figs. 2 and 3, and finger raises located about 2000 ft from the shaft. In several instances there were bends into crosscuts and up vertical distances into the forms. For the first pours two placers were used. The first was located near the shaft where the concrete could be spouted into it from a 2-cu yd concrete bucket on the cage. The second was set on the side of the drift at a point approximately 1500 ft from the shaft. The concrete was shot directly into the second placer from the first unit and from the second machine directly into the forms. After completion of several pours with the two machines, a trial pour with only one placer located at the shaft proved that the second placer could be eliminated. Since then all pours have been successfully completed with only one placer underground. As production of iron ore from the mine increased and the development program expanded, use of the cage for handling mine supplies and concrete became a major problem. This brought about the first attempt at shooting concrete vertically down the shaft for 2600 ft. A 6-in. pipeline with victaulic couplings installed during shaft sinking was used for the trial. One placer was set on surface 250 ft from the collar of the shaft so concrete could be spouted directly into it from the mixer. This machine shot the concrete 250 ft horizontally on surface to the shaft, 2600 ft vertically down the shaft, and 100 ft horizontally into the second placer located near the rib of the shaft station or plat. The second machine shot the batch into the forms, about 2000 ft. Total distance horizontally and vertically was 4800 ft. The entire time cycle for a ¾-cu yd batch of concrete from the mixer on surface to the forms underground totaled about 5 min. During the past two years the two-placer method from the mixer on surface to the forms underground has proved a very efficient means of transporting underground concrete. Advantages of using pipeline concrete are as follows: 1—Interference with normal mining operation is eliminated. When the cage, skips, mine cars, or mine openings are used for transporting concrete and materials used for making concrete, mine operation suffers in one way or another.

Jan 1, 1955

By M. Smutz, C. J. Baroch, E. H. Olson

IN 1949 an orebody containing some 10 billion lb of recoverable rare earth metals was discovered in the Mountain Pass district of San Bernardino County, California.' The following year Molybdenum Corp. of America purchased a number of claims at the deposit and a mill on the property which had been constructed to process the district's gold ores. Average composition of ore from the San Bernardino deposit is less than 0.1 pct Tho2, 25 to 35 pct calcite, 10 pct rare earth oxides, 15 to 20 pct silica, and 30 to 40 pct barite.' Rare earth content of the ore analyzes 50.7 pct CeO2, 4.2 pct Pr6O11, 11.7 pct Nd2O3;, 1.3 pct Sm2O3,, and 34.3 pct La2O3 and others.' By floating the barite and depressing the bastna-site, Molybdenum Corp. of America produced a concentrate that contained 60 to 70 pct rare earth oxides. More than 25 pct of the rare earths, however, was lost in flotation. It seemed likely that a more economical method could be found. At the present time most of the rare earths in the concentrates are converted to rare earth chlorides, which are either fed to ion exchange columns for separation of the individual rare earths or reduced to misch metal. Current investigation shows that solvent extraction may achieve this separation more economically than ion exchange. The study reported here was undertaken to develop an economical method of preparing a pure rare earth nitrate mixture from California bastnasite ore. Results indicated that more than 98 pct of the rare earths could be recovered. Several possibilities were considered for processing bastnasite ore, but only the method outlined in Fig. 1 was investigated. This involved leaching the calcined ore with nitric acid. The nitric acid process is discussed under the following headings: 1) calcination of the ore, 2) leaching of calcine, 3) filtration studies, 4) solvent extraction, and 5) nitric acid recovery. Calcination: Since California bastnasite ore contains 25 to 35 pct calcite and about 10 pct bastnasite, calcination was needed to reduce the violence of reaction with nitric acid. Weight losses of 26 to 30 pct were obtained by calcining the ore at 900°C for I hr or at 800°C for 4 hr. Longer periods resulted in no further weight loss. Leaching the Calcine: When the bastnasite calcine was leached with 30 pct nitric acid for 8 to 10 days, rare earth recoveries of only 45 to 50 pct were

Jan 1, 1960

By F. S., Mc Nicholas

A practical discussion of the theory of A block caving is presented which applies particularly to the physical conditions of the Climax orebody although the conditions are sufficiently characteristic of caving ore-bodies to provide valuable information applicable elsewhere.

Jan 1, 1950

By R. H. Frazier, J. M. Hodge, F. W. Boulger

This paper reports the results of studies of the impact properties of quenched and tempered alloy-steel plates as a function of sulfur content. It was found that the impact energy levels decreased continuously as the sulfur content increased and that there was a straight-line relationship between impact energy and sulfur content when plotted on logarithmic coordinates. Cross rolling raised the level of these Lines for transverse tests and lowered the level for logitudinal tests proportionately to the amount of cross rolling. ALTHOUGH it has been generally recognized that, for applications in which notch toughness is critical, the sulfur content of the steels used should be held to a low value, quantitative information on the effect of sulfur on notch toughness has not been available. For such applications, it is a common practice to specify minimum impact values, and in order that these may be met consistently it is important that the steel producer know quantitatively the effect of sulfur on notch toughness so that realistic sulfur content limits can be applied to the steels they produce. In many instances, particularly in flat-rolled products, impact properties are specified in the direction transverse to the principal rolling direction, so that the factors affecting the anisotropy or directionality of impact properties are also of concern to the steel producer. For some applications, furthermore, it is a common practice to increase the sulfur content of steels in order to improve their machinability, and, in such instances, the effect of this practice on notch toughness may often be of concern. This paper reports on an investigation, carried out at Battelle Memorial Institute, designed to furnish this quantitative information on the effect of sulfur on notch toughness and also to furnish further information on the factors affecting the anisotropy of impact properties in wrought heat-treated alloy steels. MATERIALS AND EXPERIMENTAL PROCEDURE The experimental steels were of intended base analysis: 0.30 pct C, 0.80 pct Mn, 0.25 pct Si, 2.5 pct Ni, 0.80 pct Cr, and 0.45 pct Mo. Steels were made with sulfur contents varying from 0.005 to 0.179 pct. The steels were prepared from 600-lb induction-furnace melts. Steels containing 0.020 pct or more sulfur (at meltdown) were melted from a charge of ingot iron (except for one heat): lower-sulfur steels were made from electrolytic iron. The charge consisted of ingot or electrolytic iron, ferrosilicon to give 0.10 pct Si, and ferromanganese to give 0.05 pct Mn. At meltdown, electrolytic nickel, ferromolybdenum, iron phosphide, and pyrite were added followed in sequence by ferrochromium, sili-comanganese, ferrosilicon, and ferromanganese. The slag was then removed and graphite added to give the desired carbon content. Bath temperature was adjusted to 2850°F and, when no other additions were to follow, 2 lb per ton of aluminum was added, immediately before tapping. Compositions of the experimental steels appear in Table I. Analyses are from single determinations, except sulfur which was analyzed in duplicate. A test sample (3 in. in diam by 6 in. long) and a 575-1b ingot were poured from each heat. The test sample was poured in a sand mold; the cooling rates of the test sample and the large ingot were approximately the same. Chemical analysis chips and metal lographic specimens were taken from the test samples. The ingot was 8 in. sq at the base and 9 in. sq at the top. A 5 X 5 X 6-in. sand mold hot top was completely filled in teeming the ingot. After solidification, the mold was stripped from the ingot which cooled to room temperature. Ingots were reheated to 2250"F and rolled to 1.9-in. slabs on a commercial mill. The slabs were box-cooled to room temperature. Sections of the 1.9-in. slabs were heated to 2250°F and rolled on a Battelle laboratory mill according to one of three schedules: 1) rolled straightaway to 0.5-in. plate; 2) rolled straightaway to 1.3-in. thickness, then cross rolled to 0.5-in. plate (29 pct cross rolling); or 3) cross rolled from 1.9-in. to 0.5-in.-thick plate (46 pct cross rolling). The 0.5-in.-straight- or cross-rolled plates were normalized at 1700°F for 1 hr and then water quenched from 1600°F. Plates were then tempered 2 hr at 1240°, 1170°, 1080°, or 860°F to obtain Rockwell C hardness of 25, 30, 35, and 40, respectively. Tempering was followed by quenching to room temperature to avoid temper embrittlement. Slack-quenched plates were isothermally transformed for 26 min at 800°F, quenched, and tempered 2 hr at 1170°F. Pearlitic microstructures were obtained by holding 168 hr at 1200° F, followed by quenching. Charpy V-notch specimens were taken both transverse and longitudinal to the main rolling direction, notched perpendicular to the plate surface, and tested. Slabs and plates which were to be homogenized

Jan 1, 1960

By A. S. Richardson

VENTILATION of the Butte mines has long been a rather difficult problem because of the natural high temperature of the rock. With increase in mining depth, higher rock temperatures have been encoun-tered, and this has caused a constantly growing demand for more effective ventilation measures. During recent years the hazards of dust in mine air have been more clearly recognized, and have necessitated the adoption of dust-prevention methods. To meet these ventilation problems in the mines of the Anaconda Copper Mining Co., a mines ventilation department was organized in 1918, to act under the direction of the general superintendent of mines. At the present time, under normal operating conditions, the force employed includes the ventilation engineer, two chief assistant ventilation engineers and eight assistant ventilation engineers. The activities of the department are, briefly: (1) planning and supervising operation of the general ventilation system; (2) planning and supervising the operation of dust-prevention measures, together, with dust sampling and related microscopic work for the quantitation of the dust samples and determina-tion of particle-size distribution; (3) the design and development of air-conditioning methods to meet present exceptionally severe temperature conditions and in anticipation of future requirements. To a large extent the technical features of the ventilation methods have been described in earlier papers by the author. This paper is written mainly to summarize past accomplishments bearing most closely on health and safety, with a somewhat more detailed account of the dust-prevention measures that have been developed comparatively recently.

Jan 1, 1938

By H. M. Chance M

The following tables have been compiled from the annual reports of the Inspectors of Mines, to determine the percentages of fatal and non-fatal casualties from roof-falls and explosions of fire-damp. As we cannot assume that every accident has teen recorded by the inspectors ; as many casualties terminating fatally after the lapse of a considerable period, are inevitably recorded as " non-fatal;" and as clerical errors may have crept into the compilation,* the figures of these tables cannot be considered absolutely correct, but the summary is sufficiently reliable to show the features I wish to differentiate. Under the heading " Miscellaneous" are included all accidents not directly attributable to explosions of fire-damp, roof-falls or fails of coal. Prominent among the numerous causes included under this head are premature or delayed explosion of blasts, accidental explosion of powder or cartridges, accidents from mine cam, falls in shafts, machine accidents, sliding of loose coal in pitching breasts, suffoca tion by choke-damp, etc., comprising in all 48 per cent. of the total number of casualties.

Jan 1, 1882

By R. R. Sayers

VENTILATION may be defined as the process by which vitiated air of an inclosed or partly inclosed space is continuously replaced by fresh air. Fresh air has been defined as invigorating pure air. Pure dry air at sea level contains the following gases:1 Analysis of Air at Sea Level PER CENT. Oxygen 20.94 Nitrogen 78.09 Carbon dioxide 0.03 Argon 0.94 Helium, krypton, neon, xenon, hydrogen, hydrogen peroxid, ammonia, ozone traces CARBON DIOXIDE LIMIT For many years carbon dioxide was used as an index of the purity of the air vitiated by the metabolism of people. It was, however, well known that the untoward effects produced on those exposed to such air was not due to the concentration of the carbon dioxide. It has been found that the untoward effects on the comfort and efficiency of those so exposed are due to the increased temperature and humidity. It has been found that men can breathe air containing many times the amount of carbon dioxide found in our worst ventilated theaters and assembly halls, which, according to Rosenau, do not contain above 0.5 per cent. carbon dioxide.

Jan 7, 1926

By R. R. Sayers

VENTILATION may be defined as the process by which vitiated air of an inclosed or partly inclosed space is continuously replaced by fresh air. Fresh air has been defined as invigorating pure air. Pure dry air at sea level contains the following gases:1 Analysis of Air at Sea Level PER CENT. Oxygen 20.94 Nitrogen 78.09 Carbon dioxide 0.03 Argon 0.94 Helium, krypton, neon, xenon, hydrogen, hydrogen peroxid, ammonia, ozone traces CARBON DIOXIDE LIMIT For many years carbon dioxide was used as an index of the purity of the air vitiated by the metabolism of people. It was, however, well known that the untoward effects produced on those exposed to such air was not due to the concentration of the carbon dioxide. It has been found that the untoward effects on the comfort and efficiency of those so exposed are due to the increased temperature and humidity. It has been found that men can breathe air containing many times the amount of carbon dioxide found in our worst ventilated theaters and assembly halls, which, according to Rosenau, do not contain above 0.5 per cent. carbon dioxide.

Jan 7, 1926

No. 345.-Assayer. A man 35 years old, or over, experienced in general mineral assaying, particularly of tin and tungsten ores. To locate in Bolivia with a strongly established house. No. 346.-A firm of consulting and managing engineers, having charge of certain coal-mine properties in Illinois, requires the services of the following: (a) Mine transitman, who has had underground experience and is capable of making accurate surveys. Salary $150 per month to start. (b) Mining engineer, possessing strong personality, and experienced both in surface and underground work, who is capable of taking complete charge of several coal properties. Salary $175 per month. (c) Four rodmen for mine surveying. Salary $85 per month to start. Candidates for the above positions should be able to report to the company's Illinois office at once. No. 347.-A South African development company will shortly require the services of a mill superintendent, who has :a general knowledge .of concentration, particularly of flotation, and is able to take charge of a copper concentrator treating 15,000 tons per month and employing 200 natives and a small number of white men. Salary is £60 per month to start, and the company supplies an unfurnished room or house, including free light, free water and free sanitary service, together with one native house servant. I A contract will be made for six months, and notice of three months by either party will be required to terminate the engagement after six months. An allowance of £75 for travelling expenses will be paid on arrival in South Africa to a single man, or £125 to a man who brings his family. Salary begins upon arrival

Jan 10, 1918

By Lewis Carroll

AS he contemplates the numerous good things the hard-working committees have evolved for the 140th Meeting of the Institute, the Editor knows just how the walrus felt when he uttered his memorable, if somewhat lugubrious lines. For there are the Annual Reception and Dinner at the Commodore, 'the Gold Supply Symposium, the luncheons, general and special, and the Annual Institute of Metals Lecture, a Round Table on Iron Ore and a wonderful Informal Dance at the Grand Central Art, Gallery, substantial general sessions, a Smoker-and many other things. -Old, friends and new, reminiscences and confidential chats, horizons pushed back by new information and adjusted perspectives, courage revived and ambitions stimulated-one with a flair for the modernistic might make something-or nothing-of the kaleidoscopic preview 'of the coming Annual Meeting.

Jan 1, 1931

By R. C. Hall

DEVELOPED to grow single crystals of alloys of high hardness and high melting points is a simple but effective apparatus described in this note. Growth from the melt, that is, by the Bridgman technique, hay be applied to metals or alloys which are physically hard as long as no phase transformation occurs on cooling to room temperature. The present apparatus was employed to grow single crystals of the ferromagnetic AI-Fe alloys above 1 wt pct Al and the Si-Fe alloys above 3 wt pct Si. Single Crystal Growth In a simple form, the method for growth of single crystals from the melt requires a molten metal charge in a pointed crucible which is slowly low-ered through a heated zone into a colder zone. Solidification starts at the bottom point and continues up the charge as the crucible is lowered through the heated zone. If a single crystal nucleates at the bottom, one crystal may grow throughout the charge under ideal conditions of slow growth.4,5 The presently developed method of growth was designed so that the chances that more than one crystal would grow were small. The single crystals were growth by the apparatus illustrated in Fig. 1. The charge was in the form

Jan 1, 1958