Search Documents

By A. A. Smith, J. S. Smart, A. J. Phillips

The preparation of a sufficient quantity of high-purity copper for extensive laboratory use in the study of impurity effects has been an integral part of a research program in progress at the Central Research Laboratory of the American Smelting and Refining Co. for the past several years. Initially the degree of purity desired was that necessary to meet two essential requirements for experimental accuracy: (I) no impurity was to be present in the copper in an amount capable of producing a detectable effect on the properties to be studied, (2) even the minor changes in propertties caused by the addition of extremely small amounts of individual elements were to be measured without significant interference from contaminants. In the course of the investigation, evidence has accumulated to justify the conclusion that this copper is of exceptional purity; in fact, no impurity can be detected by any chemical method or spectrographic technique known to the authors. The present paper describes the method of production of the copper and presents some of its properties. Preparation oF High-purity Copper The elimination of impurities from commercial electrolytic copper is accomplished by a three-step purification process. The first operation consists of an electrolysis through a purified CuSO4-H2SO4 electrolyte using bagged anodes, low current density (5 amp. per sq. ft.) and low tem- perature (25°C max.). The electrolyte is prepared from commercial Cu2SO4 and is purified by heating the solution and adding I gram Fe as Fe2(SO4)3 to each 100 grams dissolved copper; sufficient hydrated oxide of copper, prepared from Cu2SO4 and NaOH, is supplied to precipitate Fe(OH)3, which carries down arsenic, antimony, tin, selenium, tellurium and other minor constituents. Silver and remaining traces of lead are removed by addition of Na2S to the acidified filtrate, which is then reatered after standing hot overnight. The cold solution is made up to 30 grams per liter Cu and 150 grams per liter H2SO4 and introduced without addition agents into the electrolytic system, which consists of a double row of hard-rubber battery boxes with the inside webbing and partitions removed, arranged in seven steps of ascending height. Electrolyte is uniformly supplied to the two highest cells by glass siphons operating from a constant-level reservoir, and flows by gravity through the bank of seven cells, entering each at the bottom and leaving at the top. Glass air lifts continuously supply the returning liquid to the constant-level reservoir for recirculation. Each cell contains three 4 3/4 by 4 3/8 by 1-in anodes cast from high-quality electrolytic wirebar copper, various lots of which have been used with equal success. The anodes are pinned to sheet copper hangars shaped to prevent crawl of the electrolyte to the multiple-wired bus bars—which would result in fouling of the contacts—-and hang inside wool flannel bags stretched over open wood frames. The deposit

Jan 1, 1941

By A. J. Phillips, A. A. Smith, J. S. Smart

The preparation of a sufficient quantity of high-purity copper for extensive laboratory use in the study of impurity effects has been an integral part of a research program in progress at the Central Research Laboratory of the American Smelting and Refining Co. for the past several years. Initially the degree of purity desired was that necessary to meet two essential requirements for experimental accuracy: (I) no impurity was to be present in the copper in an amount capable of producing a detectable effect on the properties to be studied, (2) even the minor changes in propertties caused by the addition of extremely small amounts of individual elements were to be measured without significant interference from contaminants. In the course of the investigation, evidence has accumulated to justify the conclusion that this copper is of exceptional purity; in fact, no impurity can be detected by any chemical method or spectrographic technique known to the authors. The present paper describes the method of production of the copper and presents some of its properties. Preparation oF High-purity Copper The elimination of impurities from commercial electrolytic copper is accomplished by a three-step purification process. The first operation consists of an electrolysis through a purified CuSO4-H2SO4 electrolyte using bagged anodes, low current density (5 amp. per sq. ft.) and low tem- perature (25°C max.). The electrolyte is prepared from commercial Cu2SO4 and is purified by heating the solution and adding I gram Fe as Fe2(SO4)3 to each 100 grams dissolved copper; sufficient hydrated oxide of copper, prepared from Cu2SO4 and NaOH, is supplied to precipitate Fe(OH)3, which carries down arsenic, antimony, tin, selenium, tellurium and other minor constituents. Silver and remaining traces of lead are removed by addition of Na2S to the acidified filtrate, which is then reatered after standing hot overnight. The cold solution is made up to 30 grams per liter Cu and 150 grams per liter H2SO4 and introduced without addition agents into the electrolytic system, which consists of a double row of hard-rubber battery boxes with the inside webbing and partitions removed, arranged in seven steps of ascending height. Electrolyte is uniformly supplied to the two highest cells by glass siphons operating from a constant-level reservoir, and flows by gravity through the bank of seven cells, entering each at the bottom and leaving at the top. Glass air lifts continuously supply the returning liquid to the constant-level reservoir for recirculation. Each cell contains three 4 3/4 by 4 3/8 by 1-in anodes cast from high-quality electrolytic wirebar copper, various lots of which have been used with equal success. The anodes are pinned to sheet copper hangars shaped to prevent crawl of the electrolyte to the multiple-wired bus bars—which would result in fouling of the contacts—-and hang inside wool flannel bags stretched over open wood frames. The deposit

Jan 1, 1941

By Oliver Bowles, Carl A. Gnam

THE construction industry normally contributes extensively to the general economic welfare of all sections of the country. Billions of dollars are spent for materials and labor, and the success or failure of many business enterprises depends upon the volume of construction. The steel, aluminum, copper, cement, brick and tile, lime, gypsum, stone, sand and gravel, and several of the less prominent mineral industries are vitally concerned. Of great interest, therefore, is the accumulation of needed construction following the relative inactivity of the past five years, the recent moderate revival in building, and the prospect of a broader and more definite upturn. One may judge the magnitude of possible expenditure for construction by what has occurred in the past. The peak years were 1925 to 1928, inclusive, when the annual values of con- tracts awarded amounted to over six billion dollars. In marked contrast was the 1933 total of about 1% billion, the lowest level shown in the Federal Reserve Board Index, which goes back to 1919, and the more favorable 1935 figure of about 1.7 billion. An increase of nearly four billion over the 1935 volume would be necessary to equal the peak year 1928.

Jan 1, 1936

By I. S. Servi, N. W. Marr

TIN markedly increases the softening temperature of pure copper with only a moderate effect on conductivity. Smart and smith' indicated a substantial increase in softening temperature upon addition of different levels of tin up to 0.05 pct in oxygen-free copper. However, after finding no effect of tin in copper containing about 0.025 pct O, they concluded that "the presence of oxygen completely nullifies these changes in properties by precipitation of SnO2.'' Since preliminary tests on Cu-Sn-0 alloys indicated that this conclusion is not valid outside the extremely limited tin range investigated by Smart and Smith, research was primarily directed toward the partition of tin between the copper-base matrix and the oxide phases. Experimental. Material was prepared by sealing an 80 to 100-g charge consisting of oxygen-free copper, tin, and copper oxide into a y-in.-ID quartz capsule which was evacuated and back-filled with tank-grade argon to 3 atm. The sealed vials were heated to 1125ºC, kept at temperature for 30 min, occasionally agitated, and then allowed to air-cool outside the furnace ("as-cast"). The castings were cold-swaged to 0.370 in., annealed 1 hr at 600°C ("as-annealed"), and cold-swaged 16.5 pct ("as-swaged"). Cross sectional wafers were annealed for 1 hr at various temperatures and Rockwell F hardness measured. The "softening temperature" was defined as the interpolated temperature at which the hardness was 50 Rockwell F. Electrical resistance was measured by an ac poten-tiometric method on 0.040-in.-diam wires after a 1 hr anneal at 600°C. Relative accuracy was of the order of 1 pct. Chemical analyses for tin were performed by two methods, identified as "Acid flux" and "HN03 dissolution". The first consisted of fusing the sample with potassium pyrosulfate and leaching the resulting melt with 10 pct sulfuric acid. The spectrophotometric procedure which followed is described in Ref. 2. Oxygen analyses were performed by the vacuum-fusion method with a bath temperature of 1650°C. Tin content of oxides and copper phases was measured with the X-ray microprobe, using a calibration curve based on a series of oxygen-free Cu-Sn alloys. Results. In Fig. 1, the nominal tin composition for alloys containing nominally 400 ppm O was plotted vs the analyzed or the computed tin content—the latter derived from one of the following: 1) "acid flux" chemical analysis; 2) "HN03 dissolution" chemical analysis; 3) X-ray microprobe analysis of the copper matrix; 4) equivalent tin content, based on the measured increase in electrical resistivity (an increase in resistivity of 1.6 microhm-cm is approximately equivalent to 1 wt pct of sn1,3). It is evident from Fig. 1 that the results of the acid flux analysis are consistent with the nominal composition while the HNO3 dissolution method generally yields lower values, consistent with those obtained from electrical resistivity measurements and somewhat higher than those obtained by microprobe analysis. Microprobe and resistivity values are affected only by the tin in solid solution; hence the HN03 method

Jan 1, 1970

By F. A. Veer, W. G. Burgers, B. H. Kolster

Starting-- from Cu-Si diffusion couples a study of diffusion in the intermetallic compound Cu3Si of the Cu-Si system has been made. Mmker experiments showed copper to be the diffusing element. From the rate of growth of the Cu3Si phase diffusion coefficients were derived. The activation energy for diffusion is 18.6 kcal per mole. The couples show some interesting microscopic features, for which a tentative explanation is given. THE synthesis of dimethyldichlorosilane, (CH3)2SiC12, an important compound in the manufacture of methyl-silicones, takes place at the surface of a thin Cu3Si layer deposited on a mass of silicon particles."' By passing CH3C1 vapor at about 350°C, silicon atoms are consumed from Cu3Si in forming the volatile silane molecules, thus leaving copper atoms at the surface. It is well-known that copper acts as a poison for the above-mentioned reaction by catalyzing the dissociation of methylchloride.' However, no poisonous effect is observed, at least not before most of the silicon from the particles is converted into silane.3 This would be understandable, if either the copper atoms diffuse through the Cu3Si deposit to the underlying silicon or silicon atoms diffuse in the reverse direction to the copper, both processes resulting in the formation of new Cu3Si and so ensuring the proceeding of the reaction. In this paper experiments are described, demonstrating copper to be the diffusing element. Also a very low activation energy for the diffusion is observed. EXPERIMENTAL The silicon used contained 1 ppm Mg and 1 ppm Cu; the copper was spectroscopically pure (Fe: 2 ppm; Ag, Mg, Si: 1 ppm). The copper and silicon samples were prepared in the form of blocks of approximately 10 by 10 by 5 mm with two parallel sides by spark-machining. The blocks were ground on emery paper (grit 600), etched (copper with nitric acid, silicon with a 4:l nitric acid:hydrofluoric acid mixture), and cleaned with alcohol. As the brittleness of the silicon did not allow a welding procedure to prepare the diffusion couples, the copper and silicon blocks were pressed together in a steel clamp. The pressure exerted by the clamp brought about contact between the parts of the couple and so ensured proceeding of the diffusion. The couples were heated in a vacuum furnace (about 10"5 Torr). The temperature was stabilized within 1 pct. After a heat treatment a section parallel to the direction of diffusion was examined in the microscope and in the X-ray scanning microanalyzer. To determine whether copper or silicon is the diffusing element marker experiments were carried out using tungsten wires with a 20-p diam. EXPERIMENTAL RESULTS Figs. 1, 2, 3, and 4 give micrographs of diffusion zones of Cu/Si couples. Analysis by the electron mi-croprobe of the Cu/Si samples after a definite heat treatment revealed the existence of only one intermetallic phase as can be seen from the line scan shown in Fig. 5. From the X-ray diffraction pattern it could be deduced that this phase was CU 3 Si.4 Even when diffusion zones of considerable width (up to 600 p) were obtained, no other phases occurring in the Cu-Si system could be detected, neither by the electron microprobe nor by X-ray diffraction analysis. The optical anisotropy of the Cu3Si phase made it possible to observe the columnar shape of the crystal-

Jan 1, 1969

By A. Springer

Chemists, physicists and others, whose occupations necessitate the use of fine scales, have heretofore regretted their inability to obtain any which would remain uniformly accurate. The difference between the theoretical and the actual results obtained in the ordinary balance (provided the pivot-distances are exact) is mainly due to the frictional resistance between the knifeedges and their bearings. This frictional resistance, although reduced to a minimum in the finest scales when new, constantly increases, thereby decreasing the sensitiveness proportionately. When examined under the microscope, neither the surface of the knife-edge nor that of' its hearings ever appears perfectly smooth. Soft kunife-edges are easily blunted, whereas hard ones are brittle and liable to crumble under the effects of over-load or shock. Prof. Frederick A. Roeder for many years attempted to discover some means by ,which the knife-edge could be replaced with some device free from the above-mentioned objections. His experiments convinced him that a torsion-joint was best suited for that purpose. After he had communicated his conclusion to me, we jointly developed the system to its present form. A torsion-wire had been used for the centre of rotation, prior to Prof. Roeder's invention, but it was found impossible to replace the terminal knife-edges with torsion-joints.

Jan 1, 1884

1944 WALTER HULL ALDRIDGE New York, N Y 1946 PETER M ANDERSON Johannesburg, South Africa 1946 CHARLES CAMSELL Ottawa, Ont, Canada 1946 CHARLES AUGUSTUS CARLOW Fife, Scotland 1946 CECIL H DESCH London, England 1946 WILLIAM FRASER London, England 1917 HERBERT HOOVER New York, N Y 1941 DANIEL COWAN JACKLING San Francisco, Calif 1939 HENRY KRUMB New York, N Y 1942 ESSINGTON LEWIS - Melbourne, Vic , Australia 1921 C MCDERMID London, England 1944 WALTER C MENDENHALL Washington, D C 1942 PAUL DYER MERICA New York, N Y 1913 EZEQUIEL ORDONEZ Mexico City, Mexico 1938 A M PORTEVIN Paris, France 1937 GEORGE S RICE Washington, D C 1934 T A RICKARD Victoria, B C, Canada 1946 JOHN R SUMAN Houston, Texas 1946 WONG WEN-HAO Chungking, China

Jan 1, 1952

1944. Walter Hull Aldridge New York, N. Y. 1946. Peter M Anderson Johannesburg, South Africa 1946. Charles Camsell Ottawa, Ont. Canada 1946. Charles Augustus Carlow Fife, Scotland 1949. Erie Victor Daveler New York, N. Y 1946. Cecil H. Desch London, England 1946. William Fraser London, England 1917. Herbert Hoover New York, N. Y. 1941. Daniel Cowan Jackling San Francisco, Calif. 1939. Henry Krumb New York, N. Y. 1942. Essington Lewis Melbourne, Vic., Australia 1921. C. McDermid London, England 1944. Walter C. Mendenhall Washington, D. C. 1942. Paul Dyer Merica New York, N. Y. 1938. A. M. Portevin Paris, France 1934. T. A. Rickard Victoria, B.C., Canada 1946. John R. Suman Houston, Texas 1946. Wen-Hao Wong Chungking, China

Jan 1, 1952

1944 WALTER HULL ALDRIDGE New York, N Y 1946 PETER M ANDERSON Johannesburg, South Africa 1946 CHARLES CAMSELL Ottawa, Ont, Canada 1946 CHARLES AUGUSTUS CARLOW Fife, Scotland 1949 ERLE V DAVELER New York, N. Y 1951 EVERETTE LEE DEGOLYER Dallas, Texas 1946 CECIL H DESCH London, England 1946 WILLIAM FRASER London, England 1917 HERBERT HOOVER New York, N. Y 1941 DANIEL COWAN JACKLING San Francisco, Calif. 1950 ZAY JEFFRIES Pittsfield, Mass 1939 HENRY KRUMB New York, N Y 1942 ESSINGTON LEWIS Melbourne, Vic, Australia 1944 WALTER C. MENDENHALL Washington, D. C 1942 PAUL DYER MERICA New York, N Y 1938 A M PORTEVIN Paris, France 1934 T A RICKARD Victoria, B C, Canada 1946 JOHN R SUMAN Houston, Texas 1946 WONG WEN-HAO Chungking, China

Jan 1, 1952

[Appalachian Petroleum Section: Walter H. Chapman, chairman; Jean Freeland, first vice-chairman; John Galpin, second vice-chairman; Jack L. Trittipo, secretary-treasurer. Meets 4th Tues., Humphreys Restaurant, Charleston. Balcones Section: William E. Richards, chairman; William C. Miller, Jr., first vice-chairman; Brantley G. Myers, second vice-chairman; Harold Vagtborg, Jr., secretary-treasurer. Meets 4th Wed., Petroleum Center Club, San Antonio. Big Horn Basin Subsection: Donald G. Davis, chairman; B. E. Yester, vice-chairman; J. F. Keleher, vice-chairman; Samuel N. Conley, third vice-chairman; William O. Snyder, secretary; M. J. England, treasurer. Billings Petroleum Section: N. J. Matthews, chairman; Guy J. Lookabaugh, first vice-chairman; George O. Ellis, second vice-chairman; Robert L. Spottswood, secretary-treasurer. Meets 3rd Tues., Turf Penthouse.]

Jan 1, 1961

By John H. Walthall, Raymond L. Copson, Travis P. Hignett

In October 1942, the War Production Board requested the Tennessee Valley Authority to undertake investigations to determine the feasibility of producing alumina suitable for reduction in aluminum cells, from clays and other domestic materials, by a lime-sintering, soda-ash leaching process. The work was undertaken by the chemical engineering staff of the Authority under the general direction of the War Metallurgy Committee of the National Academy of Sciences. The investigation included small-scale tests to determine the most suitable conditions for the process, and construction and operation of a pilot plant to obtain data for evaluation of the process and for design of a plant. The results of this investigation are described in the present paper. Sources of Alumina Alumina for the commercial production of aluminum is obtained from bauxite by the Bayer process. The tremendous demand for aluminum for wartime uses is causing rapid exhaustion of the high-grade bauxite deposits in the United States. On the other hand, there is an abundance of aluminous materials such as clay and lower grades of bauxite, which are not suitable for treatment by the Bayer process because of their high silica content. The Tennessee Valley Authority has conducted research and pilot-plant work for more than 5 years on methods for the production of alumina from clay and low-grade bauxite. Particular attention has been given to the high-grade white kaolin found in Carroll County, Tennessee. Exploratory drilling has demonstrated that at least 4 1/2 million tons of kaolin containing in excess of 34 per cent AlzOI is available in this area by strip-mining methods. It has been estimated that hundreds of millions of tons of clay of similar quality occur in the Tennessee Valley region. The Process The process is illustrated in the flowsheet (Fig. I), and consists essentially of the following steps: I. Heating a mixture of clay and limestone to form a sinter containing calcium aluminate and dicalcium silicate. z. Leaching this sinter with a dilute sodium carbonate solution, to form a sodium aluminate solution and a calcium carbonate, calcium silicate residue, which is discarded. 3. Treating the sodium aluminate solution with carbon dioxide to precipitate aluminum trihydrate and regenerate the sodium carbonate solution, which is recycled. 4. Heating the aluminum trihydrate to produce alumina. The process was considered promising because of the abundance and cheapness of the two raw materials, clay and limestone; and because, as compared with an acid process, smaller amounts of critical

Jan 1, 1944

By Frederic Laist

IN the spring of 1931 an experiment was made at Anaconda with a small reverberatory furnace, with which was combined a roasting shaft. The arrangement is shown in the accompanying drawing (Fig. 1) and requires but little explanation. The general idea was to roast .flotation concentrates, mixed with the proper fluxing materials, by dropping them down a heated shaft, from which the calcines would enter the smelting zone of the reverberatory furnace through an opening in the roof. The hearth of the reverberatory was 3 ft. wide by 21 ft. long. The roasting shaft was 3 ft. square inside and had an effective height of about 20 ft. . The reverberatory furnace was arranged so that it could be charged either directly through the roof with regular hot calcines, in the usual manner, or by means of the shaft, at the top of which were a feed-ing arrangement by which cold flotation concentrates, suitably fluxed, could be fed continuously and a pipe through which cold air was blown in. Means were provided for distributing the feed over the cross-section of the roasting shaft. At first a mechanical arrangement was used but later it was found that a simple cone served the purpose equally well and gave less operating trouble. On account of the small size of the equipment, it was realized that absolute capacity and fuel consumption figures would mean but little. It was not to be expected that ratios comparable to those obtained in large furnaces could be gotten, and the only way in which any idea could be obtained as to the possibilities of the combination furnace was to run it in parallel with the reverberatory furnace charged in the usual manner and operating without the shaft. The results of such parallel runs are given in Table 1. The amount of oil burned in the reverberatory was purposely maintained at substantially the same rate during both runs in order that the benefits resulting from the shaft might be gaged.

Jan 1, 1933

By Michael Tenenbaum, C. C. Brown

IN recent years, the importance of slag control in basic open-hearth operations has been universally recognized. To effect such control during the working period of the heat, methods have been developed to measure or estimate slag oxidation and slag basicity. While satisfactory rapid chemical methods have been developed to determine slag oxidation, no completely adequate method of evaluating basicity has yet been provided. The most generally accepted control methods of measuring slag basicity are based on visual estimates. While considerable benefit may be derived from such estimates, the need for some measurable indication of slag basicity has become increasingly apparent. In a recent paper, Philbrook and Jolly[$] suggested a promising technique for making the basicity determination. Their method consists of measuring the pH of a mixture of powdered open-hearth slag and distilled water. It was found that a relation could be established between the slag basicity and the alkalinity of the water mixture as measured by the hydrogen-ion concentration. The general procedure followed in making the measurements and the considerations involved in constructing the original curves are given in the paper of Philbrook and jolly and need not be repeated. It is the purpose of this paper to discuss some of the factors considered in applying the pH measurements to actual slag control and to present some of the results of its application. FACTORS INVOLVED IN MEASURING pH OF WATER-SLAG MIXTURES To facilitate the application of the pH control system, it was desirable that no alteration be made in the routine methods of sampling and crushing the furnace slag. Some of the factors considered before establishing a curve to relate slag basicity with the pH reading are reviewed individually in the following paragraphs. EFFECT OF COOLING RATE Under actual operating conditions there can be considerable variation in the tem¬perature of the piece of slag crushed for the pH determination. To determine whether variations in crushing temperature or in cooling rate would affect the pH reading, a series of four samples was prepared from each of two separate slags. These samples represented conditions far more extreme than would actually be encountered. To obtain these samples, a thick pancake of slag was poured. One piece of this pancake was crushed immediately after it had solidified. Another piece was water-quenched and then crushed. A third piece was allowed to air-cool to room temperature before crushing. The fourth sample was prepared from a chilled slag. This sample was poured onto a heavy inclined steel plate at the

Jan 1, 1945

By Clemens Jones

A FORM of apparatus for volumetric determinations which shall possess the features requisite for the constant use of potassium permanganate, is a very desirable fixture in a well-appointed laboratory. Expedients to economize time and insure accuracy are generously employed for various other reagents, while the permanganate seems to have been consigned to the use of an ordinary burette, and a black bottle of the standardized solution. But the introduction of new, methods dependent on the permanganate, and the urgency of technical requirements where it has long been indispensable, require a revision of practice more scientific and convenient. The apparatus designed by the writer for the laboratory of the Thomas Iron Company at Hokendauqua, Pa., is so simply contrived and works with such entire satisfaction that a description of it may be of use. It may be prefaced that the characteristics of a suitable device offer some mechanical difficulties when combined in a continuous appliance. The burette, B (50 C.C. to 1/10 c.c.), shown in Fig. 1, consists of the graduated tube proper and an arm, E, fused to it below the 50 c.c. mark. At its top are rubber connections with the blast-aspirator, shown in the cut (Fig. 2) of the front view. By means of an extra stopcock, D, connection through E is established with the reservoir F. The burette is clamped Securely to a slide, C, which is counterpoised and moves freely on guides between two parallel sides, L, suitably

Jan 1, 1887

By J. O. Nelson, C. J. Altstetter

Single crystals of hcp cobalt, 3 mm in diameter and up to 35 cm long, were grown using an electron-beam, zone-melting technique. The martensitic-phase transformation was studied in single-crystalline and polycrystalline specimens by making length-change measurements as a function of temperature under various elastic compressive stresses. Upon thermal cycling, single-crystalline or polycrystalline specimens repeatedly transformed almost entirely on the same variant of close-packed plane provided the maximum temperature did not exceed 600°C. Cycling to 1000°C resulted in transformation on more than one {111} variant. This behavior is termed multivariance. The multivariant transformation occurred very rapidly at an M, temperature 2° to 6°C lower than the M, of a transformation which would result in a single-crystal product. Elastic compressive stresses (up to 253 g per sq mm) tended to lower the A, and raise the M, temperatures, decreasing the width of the temperature vs dilatation hysteresis loop. The transformation habit plane and transformation shear direction of an as-grown single crystal were not grossly affected by elastic compressi?ie stress. This was evidenced by similar dilatations on the temperature us dilatation loops joy specimens with and without compressive stress. A dislocation mechanism is proposed to explain the observed results. IT has been shown that, on heating, cobalt transforms martensitically from the hcp to the fcc phase.' The transformation habit plane is (0001)hcp || (lll)fcc and the transformation shear direction is (1010)hcp || (112)fcc. The transformation involves a shear of 1g°28', which may be achieved by a shearing of a/6(112) of every two planes with respect to the plane beneath, thus changing the ABABAB stacking of hcp to the ABCABC stacking of fcc. Associated with the phase change is a 0.3 x 10"3 contraction in the habit plane and a 4.2 X 10"3 expansion perpendicular to the habit plane resulting in a 3.6 x X volume increase on heating.' On cooling, an identical volume decrease takes place. The temperature at which the fcc phase begins to form on heating (A,) is reported as 430°C, and the temperature at which the hcp phase begins to form on cooling from an elevated temperature (A&) is reported as 390oC1,3 Consequently, temperature vs dilatation plots have the form of a hysteresis loop. If heating or cooling is reversed during a transformation, a smaller hysteresis loop results. Upon heating, the transformation is always complete; whereas, fcc is often retained at room temperature as a metastable phase entrapped in the polycrystal-line hexagonal matrix.1,4,5 Two obstacles in the theory of the allotropic-phase transformation of cobalt have been: 1) a detailed knowledge of the product nucleus, and 2) a plausible method of propagation of the transformation. Bilby,8 christian, 7 and seeger 8,9 have suggested a "pole mechanism" as a means of propagation of partiai dislocations from plane to plane. A pole dislocation and a Shockley partial come together at a node. The a/6(112) Shockley partial rotates about the pole dislocation effecting the transformation shear. The pole dislocation must have a 2a/3(111) screw component which causes extension of the transformed region by two atomic planes with each full rotation of the Shockley partial. Bollmannl0 suggested, on the other hand, that transformation propagation occurs due to the stress fields of intersecting (111)-type stacking faults. As faults intersect, a stress distribution is set up about their intersection which is in turn reduced by the emergence of another fault on the second nearest plane. This process continues with the final result of a complete phase transformation. In view of the similarities between deformation and transformation in cobalt, the effect of stress on the transformation would, hopefully, yield valuable information concerning nucleation and propagation. In the present work single-crystalline and polycrystalline specimen length changes were measured as a function of temperature at various compressive loads. PROCEDURE Several orientations of single crystals of hcp cobalt in lengths up to 25 cm were grown by electron-beam floating zone melting from 99.95 and 99.999 pct, 3-mm-diam cobalt rod as supplied by Johnson

Jan 1, 1964

By C. H. Snyder

The paper deals with details of construction of the Colmol, including improvements in design that will be incorporated in new models. These improvements are results of problems encountered and worked out in experimental operation with the unit. Also included is a descriptive plan of operating where roof and air conditions are of the worst. A summary of production results from the machine is presented.

Jan 6, 1950

By Keith R. Bock, Norman Parlee, Albert M. Barloga

Coils of pure iron and iron-carbon alloy wire (0.05 to 0.80 pct C) and sufficient sulfur to saturate the solid phase were equilibrated in evacuated or argon filled tubes. After rapid cooling, and removal of the outside nonmetallic layer, the wires were analyzed for carbon and sulfur and the data used to construct an Fe-S binary and isotherms of the Fe-C-S ternary in the range 1149° to 1427°C. THE solid solubility of sulfur in steel is of interest in connection with such phenomena as hot shortness, burning, and so forth. "Burning," the more or less permanent damage that some steels suffer when heated for forging or rolling, has been shown to be related closely to the behavior of sulfur and less closely to carbon and oxygen.' Attempts to interpret burning phenomena in steels fail because of lack of data on the Fe-C-S and the more complex systems in this family. Rosenqvist and Dunicz 2 and Turkdogan, Ignatowicz, and pearson3 have largely elucidated the Fe-S diagram in the region of interest but no information on the Fe-C-S diagram in this region appears to be available in the literature. This paper deals with the elucidation of the Fe-C-S diagram in these interesting ranges. The method employed is different from those used by previous workers2'3 on the Fe-S system. EXPERIMENTAL METHOD Pure iron wires (Ferrovac E) or iron carbon alloy wires of 1 mm in diam were cleaned with acid and acetone, coiled, and placed in silica tubes (7 mm OD and 5 mm ID) previously closed at one end. Enough sulfur was added to assure saturation of the solid iron phase. The filled tubes were either simply evacuated and sealed, or filled with argon at a reduced pressure and sealed. The argon was required at the higher temperatures to prevent collapse of the tubes. The filled and sealed tubes were placed in the middle uniform temperature zone of a Globar tube furnace and equilibrated at temperatures ranging from 2100°F (1149°C) to 2720°F (1493°C). After equilibration the tubes were removed from the furnace and quenched in air or water, the form of quenching being found to have no effect on the results. The tubes were broken open and the coils were placed in a 1 : 1 HC1 solution to remove the sulfide-rich layer. The coils were then cut into small pieces and analyzed for sulfur and carbon. In the early stages of the investigation different equilibration times ranging up to 17 hr were tried and the cores of the wires were analyzed to test for saturation. One hour appeared to be sufficient to reach maximum sulfur content at 1454°C and 2 hr sufficient at 1149°C. The practice adopted was to use at least 3 hr at the higher temperatures and at least 5 hr at the lower temperatures. The iron-carbon alloy wires used were made by carburizing pure iron wire with carbon monoxide gas in a one inch diameter ceramic tube at about 1204°C. Differing carbon contents were obtained by allowing fairly large coils to react with the gas for varying lengths of time at a flow rate of 800 cc per min. The reacting times ranged from 15 min to 4 hr depending upon the amount of carbon desired. The furnaces used were controlled by means of Leeds and Northrup Speedomax Type H instruments with D.A.T. Control attachment. Thermocouples were calibrated against the melting points of gold and copper. The temperatures recorded appear to be accurate within i2.7OC. Starting with run No. 85 and continuing with the

Jan 1, 1962

By Raymond C. Boettner

The present work had for its purpose: 1) the identification of crack nucleation sites in AISI 4340, quenched to martensite and tempered over a range of 'temperatures; and 2) the comparison of fatigue processes in AISI 4340 with processes observed previously in pure metals From constant def1ection-bending fatigue tests, martensite boundaries were identified as the favored crack nucleation sites in quenched and tempered AISI 4340. It, also, was concluded that the fatigue processes operating- in this lous-alloy steel were similar to Processes observed in pure tnetals. ALTHOUGH much engineering data has been accumulated on the fatigue properties of quenched and tempered martensitic steels,' fatigue as a process is not as well understood in martensite as it is in pure metals.' Important features of the fatigue process, such as the identity of the nucleation sites, have not been determined in the commercially important high-strength low-alloy structural steels. The present work had for its purpose: 1) the identification of crack nucleation sites in a low-alloy steel, i.e., AISI 4340, which had been quenched to martensite and tempered over a range of temperatures; and 2) the comparison of fatigue processes in the AISI 4340 with processes observed previously in pure metals. This comparison of the fatigue processes in the different tempers was restricted to the high-strain low-cycle part of the S-N curve. Under these test conditions, previous work on a number of metals has shown that a large number of cracks are nucleated in less than 30 pct of the fatigue life.3 Furthermore, crack nucleation sites are not restricted to inclusions but are also associated with intrinsic structural characteristics of the metal. MATERIAL A 20-lb ingot of vacuum-melted AISI 4340 (for composition see Table I) was hot-rolled to 1-in.-diam rod and then cold-rolled to a 1-in.-wide strip, 0.08 in. thick. Fatigue specimens, see insert of Fig. 1, were machined from the strip with the long dimension parallel to the rolling direction. m this orientation, the stringers of 1 to 2 p inclusions present in the sheet lay parallel to the stress axis in the specimens. The specimens were austenitited at 2050°F in order to obtain a large prior austenite grain size, i.e., 2 mm, which facilitated the subsequent identification of the prior austenite boundaries. A helium atmosphere was used to minimize decarburization. After austenitiza-tion at 2050°F, the specimens were transferred to a 1450°F furnace so that specimen distortion was held to a minimum in the subsequent oil quench. Previous work4 indicated that refrigeration in liquid nitrogen prior to tempering reduced the percentage of retained austenite in the quenched specimens to less than 5 pct. Tempering was carried out in air over the temperature interval of 200°to 800°F to produce a range of mechanical properties, Table I. The preparation of the fatigue specimen was completed by grinding about 0.005 in. from each surface and electropolishing in a chrome trioxide-acetic acid solution for 30 min. Examination of etched cross sections of specimens prepared in this fashion showed the foregoing specimen preparation to be adequate for the removal of the decarburized layer present after the heat treatment. Transmission electron microscopy showed that the as-quenched microstructure of this alloy consisted of a mixture of martensite plates containing either a high density of dislocations or microtwins. Previous work5'6 indicated that in the course of oil quenching autotem-pering resulted in the formation of E carbide on the martensite and microtwin boundaries. Tempering for 2 hr at temperatures up to about 400°F resulted in further precipitation of the E carbide. Finally, at about 400°F, cementite began to replace the E carbide on the martensite and microtwin boundaries in addition to forming a Widmanstatten structure within the plate matrix. EXPERIMENTAL S-N curves were obtained using electropolished specimens cycled at 1800 cpm as cantilever beams in fully reversed bending at selected constant deflections. The deflections were translated into surface strains by means of a calibration curve obtained through the use of strain gages. An argon atmosphere was used to minimize environmental effects. To investigate the development of fatigue slip bands, the specimens of the different tempers were unidirec-tionally bent to a surface strain of 0.005 to 0.007, photographed to record the location and appearance of slip bands so introduced, and then cycled to failure

Jan 1, 1968

By L. S. Panyity

The inception of this paper may be traced directly to the various discussions of another paper by the writer1 wherein certain indefinite beliefs and opinions were emphasized as to the relative importance of total sand porosity and the actual size of the openings between the grains. Since publication of that paper it has been possible to study various methods of sand analyses and results that have been obtained under different conditions and actual operations in the field. The purpose of this paper is to indicate the value of screen analysis, especially in areas where repressuring by means of water-flood, air or gas is being used in the partly depleted fields. Sand samples have been analyzed for porosity, saturation and grain size. They are mainly from the Bradford water-flood area, where a great reliance has been put upon such analyses, and where many data are available, A few sand studies are included from fields other than the water-flood area, in order to indicate the possibilities of screen analysis in any field. Examples of various conditions are given in Figs. 1 to 7, which show the porosity, saturation and grain-size analyses of submitted cores or drill cuttings. The generally accepted methods of delineating such sand studies on cross-section paper, known as "core charts" has been employed; with the exception that a method of representing grain size has been evolved which is believed to be the best adapted for this purpose. It differs from the block diagrams generally used, in the employment of a linear section. Percentage of grain-size is represented by the subdivision of a given distance, where the total length represents the whole sample of rock chunk, while the subdivisions indicate the percentages of grains of the different sizes that will pass through the various sieves, through which the samples of crushed sand are sorted to determine the size and amount of the components that make up the aggregate. Thus, on Fig. 1, under the heading of Grain Size, the first samples are composed of grains of the following sizes: 16 per cent. through 120-mesh sieve; 33 per cent. through 150-mesh; 25 per cent. through 180-mesh; 26 per cent, through 200 mesh; a total of 100 per cent. A minus sign is placed before

Jan 1, 1931

By L. W. Rowe, S. S. Cole

A laboratory bench scale unit is described whereby finely divided chlorinatable residues are held for a short period by a restraining bed of a coarse-grained ore of comparable composition to permit 'flash' chlorination of the high surface area powder. Results on chlorinating a finely divicled titania residue using rutile sand as the restraining bed showed that 92 pct utilization of chlorine and equivalent conversion of TiO2 in the fine residue to Ticl4 were attained with a dust loss of about 3 to 4 pct and an equivalent amount of ch1om'nation of the titanium values in the restraining bed. THE chlorination of coarse grain titaniferous ores; i.e., 20 to 150 mesh sizes in fluidized beds is practiced commercially.' One effective method found for the chlorination of a very fine material in a fluidized bed is the "flash" chlorination technique.' By charging the finely divided charge material into the bottom of an established bed of optimum sized rutile, ilmenite, titanium beneficiate, or even an inert material such as sand, chlorination occurs before the dust can pass through the bed. The major requirement is that the bed be less chlorinatable than the charge. In this process, the charge consists of a finely divided (between one and 50 µ) titania residue obtained from a titaniferous ore beneficiation process. The charge is blended with a 20 pct wt basis addition of 20 to 60 .mesh size low volatile coke (to minimize hydrogen chloride formation) and fed to the bottom of the bed with the chlorine gas stream. A ball check device is used to permit entry of the charge and prevent the bed from discharging when the gas flow is cut off. The coarse pieces of coke serve to reduce compaction in the charge mixture and permit sat]sfactory feeding without plugging or jamming. Feed and gas rates are adjusted to provide for complete reaction of the charge material, with 90 to 95 pct chlorine efficiency, and maintain a gas flow in the range of 0.4 to 0.6 ft per sec. The equipment consisted of a 3-in. diam mullite tube enclosed in an electric furnace. A bow-shaped 3/4 in. Saran tube fed the charge from an air lock type of feed hopper (to prevent the escape of the chlorine gas into feed bin) to the bottom of the bed. The charge rate was set by providing a small awiliary hopper below the feed hopper where a weighed portion of the charge could be discharged in a specified time interval into the main chlorine stream. The chlorine rate was measured by a flowmeter. The reaction tube was filled with a bed of Australian rutile ore, this restraining bed serving two purposes; i.e., it rapidly heated the fresh charge to the reaction temperature and retained the particles in the bed for a sufficient time for selective chlorination to proceed. Due to the fine particle size and open, porous structure of the charge, this reaction was almost instantaneous, and, with proper adjustment of feed and gas rates, very little fine material passed through the bed without reacting and only a very small fraction of the restraining bed was chlorinated. A typical reaction procedure was to fill the bench scale fluidized bed unit with a 1 kg charge of Australian rutile ore analyzing 95.5 pct TiO2, 0.6 pct FeO, a beach sand deposit 40 to 150 mesh size. When fluidized, the bed was approximately 2 ft in depth. The ore was fluidized with a 1:l mixture of chlorine and nitrogen at a rate of 0.40 ft per sec. This gas mixture was necessitated by the comparatively short bed depth; a larger unit, with a deeper bed, could be fluidized with chlorine alone without significant free chlorine loss. Feed rate was 8.0 g per min of beneficiated ilmenite analyzing 85.0 pct TiO2, 2.6 pct FeO plus 1.6 g per min of 20 to 60 mesh petroleum coke. The

Jan 1, 1962