Search Documents

By G. W. Jones, G. S. Scott

Economic waste caused by mine fires may become considerable,l5 especially if a fire is allowed to spread or temporarily to get beyond control. It is important, therefore, to act promptly whenever a fire is suspected and to make every action count. To contribute toward its extinction effectively it is necessary to know at the earliest possible moment, and continuously thereafter, what is happening at the seat of the fire, which may be in a remote or inaccessible area, and also to recognize what may be expected as a result of any proposed combative measure. In combatting a fire the mining engineer and the chemist should cooperate, first deciding upon the course of action to be taken and then drawing upon the mining engineer's intimate knowledge of the physical structure of the fire area, the cost and time required to carry out proposed operations, and the probable efficiency with which these operations could be performed, and upon the chemist's knowledge for the results to be expected therefrom. After the initial steps to be taken have been decided, it devolves upon the mining engineer to see that they are carried out and upon the chemist to evaluate the results and to keep the mining engineer continuously informed in regard to a variety of matters—such as the composition and toxic or asphyxiating properties of the atmosphere in which the men may be working, whether the fire is increasing or decreasing in intensity and its probable temperature, the quantity of air leakage and the explosion hazards of the fire area. The purpose of this paper is to discuss what the chemist can and cannot contribute as a member of the fire-fighting personnel. The technical literature contains several hundred papers relating directly and indirectly to mine fires, and this fact alone is testimony to the complex nature of the phenomena involved in the birth, life, and final demise of a fire. A fire may be stopped (I) by preventing oxygen from reaching the coal or (2) by removing the conditions necessary for the rapid reaction of coal with oxygen; i.e., decreasing the temperature. All methods of prevention or control necessarily must be based upon one or the other, or both, of these two principles. The chemistry of a fire may be understood readily if the low-temperature oxidation of coal is considered as a starting point; then oxidation at higher temperatures (or combustion); and with these, the composition of the solid and gaseous products resulting from the oxidation or from the effects of the heat liberated. This discussion refers particularly to Pennsylvania anthracite, although much of the material applies equally well to coals of lower rank. Oxidation of Coal Oxidation of coal fundamentally is confined to the surface; that is, the rate at which oxygen penetrates into the interior of a solid block of coal is so slow that it may be ignored."16 Oxidation starts when a fresh surface is exposed, and the rate is

Jan 1, 1942

By G. S. Scott, G. W. Jones

Economic waste caused by mine fires may become considerable,l5 especially if a fire is allowed to spread or temporarily to get beyond control. It is important, therefore, to act promptly whenever a fire is suspected and to make every action count. To contribute toward its extinction effectively it is necessary to know at the earliest possible moment, and continuously thereafter, what is happening at the seat of the fire, which may be in a remote or inaccessible area, and also to recognize what may be expected as a result of any proposed combative measure. In combatting a fire the mining engineer and the chemist should cooperate, first deciding upon the course of action to be taken and then drawing upon the mining engineer's intimate knowledge of the physical structure of the fire area, the cost and time required to carry out proposed operations, and the probable efficiency with which these operations could be performed, and upon the chemist's knowledge for the results to be expected therefrom. After the initial steps to be taken have been decided, it devolves upon the mining engineer to see that they are carried out and upon the chemist to evaluate the results and to keep the mining engineer continuously informed in regard to a variety of matters—such as the composition and toxic or asphyxiating properties of the atmosphere in which the men may be working, whether the fire is increasing or decreasing in intensity and its probable temperature, the quantity of air leakage and the explosion hazards of the fire area. The purpose of this paper is to discuss what the chemist can and cannot contribute as a member of the fire-fighting personnel. The technical literature contains several hundred papers relating directly and indirectly to mine fires, and this fact alone is testimony to the complex nature of the phenomena involved in the birth, life, and final demise of a fire. A fire may be stopped (I) by preventing oxygen from reaching the coal or (2) by removing the conditions necessary for the rapid reaction of coal with oxygen; i.e., decreasing the temperature. All methods of prevention or control necessarily must be based upon one or the other, or both, of these two principles. The chemistry of a fire may be understood readily if the low-temperature oxidation of coal is considered as a starting point; then oxidation at higher temperatures (or combustion); and with these, the composition of the solid and gaseous products resulting from the oxidation or from the effects of the heat liberated. This discussion refers particularly to Pennsylvania anthracite, although much of the material applies equally well to coals of lower rank. Oxidation of Coal Oxidation of coal fundamentally is confined to the surface; that is, the rate at which oxygen penetrates into the interior of a solid block of coal is so slow that it may be ignored."16 Oxidation starts when a fresh surface is exposed, and the rate is

Jan 1, 1942

By J. Ruben Velasco, Roland B. Mulchay

CANANEA has long been recognized as a remarkable field for geologic study. The copper deposits and rocks of the district have been described by many geologists and engineers, but only the most general correlations have been made between Can-anea sedimentary rocks and other known sedimentary sections in the southwestern United States and northern Mexico. The present paper describes the Cananea sediments in greater detail than has been done before and attempts to fit the Cananea sedimentary section more closely into the geologic time table. The lack of well-preserved fossils has made it difficult to date the sediments accurately in geologic time, but it is possible to make tentative correlations between the Cananea sediments and the southeastern Arizona sections, based largely upon lithology and general position in the geologic column. It appears that sedimentation at Cananea and Bisbee may have been closely similar during Paleozoic time. Even such generalized correlations, however, may be subject to considerable modification in the future. The present study has led to the recognition of other problems of age and mineralization relationships in the Cananea district. Cananea is located in the north-central part of the state of Sonora, Mexico, at an elevation of 5270 ft. It is about 135 miles northeast of Hermosillo, the state capital, and 25 miles south of the international boundary. By road Cananea is 40 miles from the twin towns of Naco, Ariz., and Naco, Sonora, and about 50 miles from Bisbee, Ariz. It is served by the Nogales-Naco branch of the railroad, F.C. Pacifico, and is connected with Chihuahua and Mexico City by the Aeronaves airline. The headwaters of three rivers flowing to the Gulf of California are located in the Cananea Mountains: the San Pedro River, flowing to the north; the Sonora River, flowing south and west; and the Mag-dalena River, flowing west. Elenita Mountain, the highest point in the district, has an elevation of 8140 ft. The Cananea Mountains extend in a series of north-south to northwest-southeast spurs and ridges and are surrounded by gently sloping gravel plains. The mineralized area, lying across the southern and central parts of the range, is about 6 miles long and at most 2 miles wide. Elevations at the mines vary from 5300 ft at Cananea-Duluth mine at the southeast end of the district to between 6000 and 7000 ft at the west end of the mineralized area at Puertecitos-Elenita mines. Principal production has been from the intensely mineralized and altered area of Capote Basin in the central part of the district and the immediately surrounding area to the southeast. The district has produced over 2 billion lb of copper, substantial molybdenum, and minor amounts of lead, zinc, silver, and gold. Total production through 1949 is estimated at more than $300 million. In 1900 large-scale development was started at Cananea by W. C. Greene. Until World War II only high-grade ores were exploited; low-grade ores were extracted after the installation of a large concentrator in the early 1940's, and subsequent operations have been based upon mining and processing ores containing less than 1.0 pct copper from open-pit and underground workings. Mining and concentration of such low-grade ores, however, are made possible only by continued high copper prices, and active exploration for high-grade orebodies has been continued throughout the important mineralized areas. General Geology Study of the involved rock pattern at Cananea has indicated a complex geologic history for the district. Widespread alteration and mineralization have masked many of the salient features and have led to widely varying geologic interpretations over the years. Further work will probably disclose new information which will modify current beliefs. At Cananea a conformable series of sediments of probable Paleozoic age was deposited on an unknown basement. Following Paleozoic time there was an extended period of erosion common to many districts in the southwestern U. S., and there is no present evidence of marine sedimentation at Cananea after the Paleozoic. The eroded surface was eventually covered with a great thickness of extrusive volcanic rocks. The entire series of sediments and volcanic rocks was later intruded by a variety of deep-seated igneous rocks. These included the Cananea granite, the Cuitaca granodiorite, the El Torre syenite, the Tinaja diorite, the Campana diabase and gabbro and the Colorada rhyolite quartz porphyry. Faulting of early age, probably prior to the deposition of the volcanic rocks, may have been responsible for the present position of some of the intrusive rock masses. In the Capote mine on the third and fourth levels the northwest-striking Rick-etts fault zone, with apparent offset of about 800 ft, has been sealed by a dike-like mass of Cananea granite which gradually increases in size with depth. In lower levels of the mine the granite forms a large southeast-plunging mass generally following the course of the Ricketts zone. The granite is not known southeast of the Capote-Oversight mine areas and the Ricketts fault does not appear in the vol-canic~ southeast of Capote Basin, but several plugs of Colorada quartz porphyry cut the volcanics along the assumed general southeast trend of the Ricketts zone. These porphyritic intrusives may be the up-

Jan 1, 1955

By Joseph Ames

THERE are two distinct questions associated with the concept of temperature: one is practical, the other is theoretical. Our fundamental ideas of temperature come from our senses; we know what we mean by the words "hot" and "cold," or by saying one body is "hotter than another." But for scientific purposes words require definition. We are guided in this matter, as in all other scientific questions, by our knowledge of facts of observation. When two bodies at different temperatures are intimately associated, e.g., a hot stone is, dropped into a pail of water, our experience is that ultimately they come to the smile temperature as far as our senses can tell; the hot body becomes colder and the cold body hotter. In the case of a block of ice, immersed in, water, the ice melts, forming cold water, which then mixes with the other water, the final result being water colder than the original water. From our knowledge of the nature of heat phenomena, we learn that in this process one body loses, heat and the other gains heat, the condition of equilibrium being, one in which each body gains Is much heat as it loses. It is distinctly assumed in this statement that only two bodies are concerned in the transfer of heat, all other bodies being rendered in some way impervious to heat. The body that in the process loses heat is said to have the ?higher temperature" while the body that gains the heat is said to have the "lower temperature;" and, when thermal equilibrium is reached, the two bodies are said to have the "same temperature." Consequently, the temperature of a body may be defined, is it was by Maxwell, as "its thermal state considered with reference to its power of communicating heat to other bodies."

Jan 9, 1919

By R. T. Hukki, P. Voutilainen

This paper describes a new apparatus for continuous wet fine-screening. Its preferred size range seems to be from 0.1 to 1 mm. The supercritical trommel screen is a short cylindrical trommel of wedge-bar type construction operated at a speed greater than the calculated theoretical critical speed and at a speed lower than the speed at which particles introduced into it will centrifuge. The paper describes results obtained with the prototype supercritical trommel screen in pilot plant scale. The results point to a high capacity and simultaneously to a high sharpness of screening. Finally, an analysis is presented of the forces acting in screening on a supercritical trommel screen. In the era of high speed, high capacity processing of raw materials the conventional slowly rotating trommel screen is often considered a relic from the times passed. A typical trommel screen is the cylindrical trommel rotated about a horizontal or slanting axis at a relatively low speed. Its screening characteristics are well known. Trommel screens of various types of construction, methods of operation, performances and other characteristics have been described in detail by Taggart.1 The theoretical critical speed of a trommel screen is defined by the same well known equation as that applied for grinding mills: where ncritical = the numerical value of the theoretical critical speed in rpm, D 1 = the inside diameter of the trommel in feet, and D2 = the inside diameter of the trommel in meters. ncritical corresponds also to the centrifuging speed provided that the coefficient of friction f between the trommel surface and the outer layer of the charge is = 1.0. In a general case: From Eq. 2 it is seen that in all cases where f < 1.0 the centrifuging speed of the trommel is greater than the theoretical critical speed. The supercritical trommel screen concerns screening operations within that speed range which is between the theoretical critical speed defined by Eq. 1 and the centrifuging speed defined by Eq. 2, under conditions such that the coefficient of friction f<1.0. It is reported by Taggartl that the optimum speed of a conventional cylindrical trommel screen 36 in. in diam was experimentally found to be about 16 rpm. From Eq. 1, the critical speed of this trommel is 44.2 tpm. The indicated optimum speed corresponds to (16/44.2) x 100% = 36.2% of the theoretical critical speed. The optimum speed range based on information available seems to vary from 33% up to 45% of the theoretical critical value. The trommel screen operated at a supercritical speed: operates at a speed greater than the calculated theoretical critical speed; operates at a speed lower than the speed at which the charge introduced into it will centrifuge; operates within the supercritical speed range in such a way that the coarse fraction of the charge must slide in respect to the inside surface of the trommel; the outer layer of the said fraction next to the screen tends to proceed in the same direction as any selected point on the trommel surface, but now at a lower speed, and indeed at a subcritical speed; allows to a certain degree adjustment of the maximum determining particle size x of the fine product simply by a variation of the speed of the trommel within the supercritical speed range. With increasing trommel speed, finer and finer material only will get the opportunity to find its way into the fine product while the screen opening remains constant. In conventional practice, the low speed trommel is generally used for sizing of coarse and medium coarse material, but seldom for fine screening. The characteristic feature of the product passed through the conventional trommel is that the determining size x of the biggest particle is barely smaller than the nominal size of screen opening. The supercritical trommel screen, on the other hand, is best suited for sizing of relatively fine material. Furthermore, the characteristic determining size x of the biggest particle in the fine product can be substantially smaller than the nominal width of the screen opening or slot. In the trommel screen best suited for the applications

Jan 1, 1965

By Ralph A. Sherman

In these days of intense competition for the domestic fuel market much is heard of the low efficiencies with which solid fuels, and most particularly bituminous coal, are burned in domestic heating equipment. In contrast to the every-day operating efficiencies of 85 and 90 per cent in large, central, electric-generating stations, efficiencies of 50 per cent and lower are cited for the hand-fired home furnace. Just as the miles per gallon of gasoline is only one of the factors that determine the cost of operation of an automobile, so the thermal efficiency is only one factor in the cost of domestic or other heating. The purpose of this paper is to analyze the total costs of domestic heating by various fuels and types of equipment, to determine the relative importance of efficiency and other factors, and to discuss what this signifies relative to the future of the use of fuels in the home. Factors That Govern the Choice of Fuel and Burning Equipment A rational, intelligent selection of fuel and equipment for heating the home would consider two groups of factors: Cost Factors Convenience Factors 1. Cost of potential heat in fuel 1. Attention 2. Efficiency of combustion and heat transfer 2. Dirt 3. Fixed charges 3. Noise a. Interest b. Depreciation c. Repairs 4. Power costs 5. Cost of handling ash and refuse. As just stated, the purpose of this paper is to analyze the relative importance of the five cost factors and not to discuss particularly the relative total costs of different methods of heating. However, to arrive at the percentage costs and to show clearly how they were determined, a statement of the total costs is unavoidable. One example only will

Jan 1, 1934

By C. W. Volek, G. Mandl

Steam-injection tests in the field have shoum that heat transport into the oil/water region, ahead of the steam zone, may have a significant effect on the production process. Earlier theoretical work on reservoir heating by hot-fluid injection can be used to describe the growth of the steam zone, but only if heat transport from steam zone into oil/water region is neglected. It therefore became necessary to re-examine and extend the earlier theory. It was found that this theory ceases to be consistent with the physical model of the process at a certain critical time, tc, which depends on reservoir thickness, temperature, and quality of the steam. The critical time marks an important change in the heat flow across the condensation frovt: the heat flow, which is purely conductive during 0 < t < tc&apos; becomes predominantly convective at t = tc. Accordingly, at t = tc, the equation which governs expansion of the steam zone changes. On the basis of the new equation, an approximate description for the steam-zone growth during t > tc is developed by making use of upper and lower bounds for the exact solution of the problem. The boundary conditions for heat and mass flow inside the oil/water region are established, and a simple method of detennining the saturation at the downstream side of the condensation front is presented. Experimental results show that the theory gives an accurate description of steam-zone expansion before the critical time. At times near critical time, and also after critical time, experimental data show theoretical steam-zone volumes to be high. Even so, the accuracy of the calculated steam-zone volumes is sufficient for practical purposes. THEORY OF STEAM-ZONE GROWTH INTRODUCTION The engineering evaluation of steam-drive processes is based mainly on a mathematical description of reservoir heating by hot fluid injection presented several years ago by Marx and Langenheim.l This theory can be used to determine the growth of the steam zone,2 provided the flow of heat from the steam zone into the liquid zone ahead of the condensation front (Fig. 1) is neglected. Since we must expect, however, that heat transport into and inside the liquid region (the region between condensation front and production wells) will affect both the water/oil flow and the growth of the steam zone, it is necessary to re-examine and to generalize the Marx and Langenheim theory as applied to steam drive, which will hereafter be termed the "old" theory. Observations made in several field tests emphasize the need to study the heat flow across the condensation front (CF). On several occasions it was discovered that heat was transported in the liquid zone far ahead of the advancing CF, resulting in an early breakthrough of warm water. This seems to occur most often when high injection pressures are applied, when "wet" kONINKLIJKE/SHELL EXPLORATIE EN PRODUKTIE LABORATORIUM RIJSWIJK, THE NETHERLANDS SHELL DEVELOPMENT CO. HOUSTON, TEX.

Jan 1, 1970

By Hugh P. Nicholson

IN view of the many articles that have been written on the proper classification of mining systems without so far having produced any particular tangible results it might seem that the subject is hopeless of solution. I do not believe that is so, and my intention in contributing the following outline is to present a slightly different viewpoint. Too much attention is often focused on unnecessary details and not enough on general principles. Too much attention and emphasis is often given to the system employed at one particular mine or in one particular district. In addition, names that are entirely misleading are applied to mining systems, and their adoption by the coming generation perpetuates a condition that needs clarification badly. The following classification is the result of several years of practical experience in mining and also several years&apos; practice in teaching the same subject. It therefore represents a broad picture of the entire field of mining systems from the viewpoint of the miner as well as the teacher. It seems that the difficulty in the past has been in reconciling these two viewpoints. The need of such a reconciliation requires no explanation.

Jan 1, 1934

By Horace C. Porter

Most of the bituminous and semibituminous coals of this country will coke, and all of them yield, on carbonizing, more or less marketable gas and byproducts. We need, however, a finer distinction as between various grades of coking coals and between coals of different degrees of byproduct and gas-making possibilities. There is required by the consumer or the coal producer a dependable test to show whether a certain coal or mixture of coals will make coke of good commercial value for blast-furnace, foundry, water-gas, or domestic use; whether any difficulties in operation may arise from properties inherent in the coal; and whether gas and byproducts may be expected of good quality and in profitable quantity. For determining coke quality, the most dependable test is an actual run in an oven, but for byproducts a coal may better and more accurately be tested in the laboratory or in a miniature oven or retort. As to what are the most desirable qualities in blast-furnace coke, the furnace men themselves are not in complete agreement. Some desire a hard, well-burned, "hot" coke, and others get better results from a llgreener," less hardened product that burns somewhat more readily in the furnace. But certain qualities of cell structure and porosity are commonly agreed upon as desirable. Information as to what kind of coke a certain coal may be made to yield is valuable in advance, whatever may be the consumer&apos;s ideas as to the particular kind most suitable to his needs. The question arises, Can we predict coking quality with any degree of satisfaction from a small-scale test? It used to be said that coals could not be tested satisfactorily on a laboratory scale either for the coke they would yield or the byproducts. On account of the mystery with which the coking quality of coal has been shrouded and the large determining influences that many believe are exerted by mass, pressure, and the passage of carbonaceous volatile matter through the coking material, it has seemed difficult to reproduce in the laboratory the exact conditions of commercial practice. Great progress, however, has been made in recent years in elucidating the process of carbonization and many of the factors that make for the formation of high-grade coke and the recovery of the best

Jan 1, 1920

By G. St. J. Perrott

ONE of the important hazards in coal mining is the danger of ignition of explosive mixtures of methane and air or coal dust and air, or both, by the explosives used in blasting the coal. It has long been recognized that certain explosives are more dangerous than others in this respect. In America and abroad, government testing stations have been established for officially passing on the suitability of explosives for use in coal mines. In this country the Federal government is given no power to enforce the use of the approved explosives but merely publishes from time to time, through the Bureau of Mines, those explosives which have passed the tests necessary to place them on the list for use in coal mines. In spite of this lack of police power, the increase in the use of permissible explosives since the promulgation of the first list in 1909 has been rapid. In 1912, only 8 per cent. of the explosives used in coal mines were permissible; in 1925, this figure had increased to 25 per cent. While the past record of permissible explosives has been most gratifying, it is very desirable that we pave the way for further improvement in explosives and blasting methods by learning more about the mechanism of ignition of gas and coal dust by explosives. To this end a considerable amount of investigative work already has been carried out and a large amount yet remains to be done. It is the purpose of this paper to discuss briefly the effect of the characteristics of explosives and method of loading in the borehole on the liability of a blown-out shot to ignite explosive mixtures of gas or dust. For an account of the methods by which an explosive is tested for permissibility for use in coal mines, the reader is referred to Schedule 17-A of the U. S. Bureau of Mines.

Jan 10, 1926

By Charles M. Brown, Russell Franks, W. O. Binder

Occasionally in the application of the austenitic chromium-nickel steels to corrosive conditions, failures have occurred by cracking without serious general over-all attack of the metal. As pointed out by Foyt and Scheil(1),2 and by Scheil, et al.(2) as well as by Hodge and Miller(3), the stress-corrosion failures that have occurred have been limited in number, and have taken place only when the steels were exposed to certain corrodents. These investigators have stated that while stress- corrosion cracking can be intergranular in nature and originate at the grain boundaries of the austenitic chromium-nickel steels, it can also take place in trans- granular fashion. They have shown that the cracking may be either initiated at the grain boundaries and may propagate along grain boundaries for some distance and then suddenly extend across grains, or it may begin in a transgranular fashion and suddenly proceed along grain boundaries until the cracking stops. Their data further show that when austenitic stainless steel is subject to intergranular attack, stress will concentrate and cause cracking in service. These investigators have studied the effect of the metals titanium and columbium which are added to the steels to impart immunity to intergranular attack, and molybdenum which is added to improve resistance to general corrosion.

Jan 1, 1945

By Harold B. Janzen, M. A. Nobles

Campbell and Martin1 described a new exploratory logging tool which was developed as the result of a new concept of the phenomenon that takes place when a porous formation containing mobile hydrocarbons and irreducible interstitial water is invaded by mud filtrate. They postulate that invasion will create a bank of interstitial water between the flushed zone and the undisturbed formation. This postulate was confirmed by Wyllie.&apos; Thus, if R,, is greater than R, and mobile hydrocarbons are present, the resistivity profile with increasing radii from the borehole is high:low:high, as shown in Fig. 1. If mobile hydrocarbons are absent, the bank of interstitial water is indistinguishable from the undisturbed formation and the resistivity profile, when R is greater than R,, is high:low, as shown in Fig. 2. The zone containing the bank of interstitial water and residual oil was named the "low zone". Campbell and Martin conducted extensive electrolytic wedge and resistivity analog model studies to select a logging system that would reflect the presence or absence of the low zone. The system they selected was that of a family of lateral curves. The model studies indicated that the presence of a low zone could be detected in approximately 60 to 70 per cent of the producing sand reservoirs with a family of lateral curves provided that the sonde effectively occupies 90 per cent of the diameter of the hole. These studies were conducted with D, = 5d. The presence or absence of the low zone is best determined by a plot of the apparent resistivity vs spacing as shown in Figs. 3 and 4. A dip or inflection in the profile that repeats at successive depth intervals is considered diagnostic. To reduce the shunting effect of the hole and mud, a sonde of insulating material that is surrounded by a series of flexible rubber bumpers was designed. The bumper efficiency is considered to be the ratio of the bumper diameter to the hole diameter. Field tests conducted by Campbell and Martin on 10 wells with a tool that provided for station readings indicated that dips or inflections could be detected in 19 out of 25 known producing zones. INSTRUMENT DEVELOPMENT Halliburton developed a logging system to simultaneously and continuously record eight lateral curves. The instrumentation is described in the literature.&apos; The original logs made

By W. N. Logan

WHAT is mineral wool? This question is frequently asked by those unacquainted with its manufacture. The word "mineral" suggests that it is of mineral origin; the word "wool" suggests that it is of animal origin; but the only similarities it has to wool are its fibrous character and its white fleecyness. Mineral wool is a fiber produced by melting rock to a glasslike condition and blowing the glass into fine white, wool-like threads. A -number of the products fabricated from-mineral wool are used for some form of insulation, but mineral wool is adaptable to many other uses. It is used in the manufacture-of pipe covering designed to with; stand the high temperatures produced in steam pipes. In a similar form of insulation it is used to cover boilers and furnaces. It is used in ,the fabrication of upholstery tow for sofas and car seats: In acoustics it has many uses, such as acoustifibroblock, which is used in floors to destroy sound and vibration, and acoustic mat, which is used under carpets to destroy sound. In the insulation of houses, loose wool and granulated wool are used beneath attic floors and between the studding in frame buildings to prevent the escape of heat in winter and the entrance of heat in summer. Mineral wool is used also in fabrication of linofelt, which is a quilted form of insulation; in fibrofelt, which is an insulating board; in the fabrication of lith, which is an insulating block; in anti-fibroblock ,which is used in insulation and refrigeration; in flexfelt; in loose wool; in pressed block; in heavy oiled wool; in dark oiled block; and for many other purposes. The materials used in the manufacture of mineral wool are of two kinds. The first is a rock which contains silt, clay and silica, with smaller amounts of lime and magnesia. The second is a more highly calcareous rock which may carry a small amount of magnesia. The latter is used as flux to assist in the melting of the former. The relative proportion of the alumina-iron-silica content to the lime-magnesia content is normally as fifty to fifty but a considerable range is possible.

Jan 1, 1932

By Charles E. Lundin

Pressure-temperature-composition data were obtainedfor the Er-H system. Measurements werecar-ried out in the temperature range of 473° to 1223°K, the composition range of erbium to ErH,, and the pressure range of 10-5 to 760 Torr. Solubility relationships were established from these data throughout the system. Three solid-solution phases were delineated: metal solid solution, dihydride phase, and trihydride phase. The trihydride Phase decomposes at about 656°K and 1 atm pressure. The dihydride phase is stable to about 1023°K, but becomes more deficient in hydrogen above this temperature. The equilibrium decomposition pressure-temperature relationships in the two-phase regions, erbium solid solution plus dihydride and dihydride plus trihydride, were deter- The differential heats of reaction in these two regions are AH = - 52.6 * 0.3 and - 19.8 i 0.2 kcal per mole of Hz, respectively. The differential entropies of reaction are AS = - 35.2 * 0.3 and - 30.1 * 0.4 cal per mole HZ.deg, respectively. Relative partial molal and integral thermodynamic quuntities were calculated in the system to the dihydride phase. RARE earth metal-hydrogen systems have been the subject of general survey,1"4 and all have been found to form hydride phases. The heavy rare earths, of which erbium is a member, form dihydride and trihydride phases with different crystal structures, whereas the light rare earths form only a single-phase dihydride which expands without structure change, as hydrogen is added, to the trihydride composition. These materials are of interest primarily because of their theoretical properties, such as bonding, defect structure, and thermodynamic and electronic characteristics. Erbium has been studied in several previous investigations.5, 6 It was deemed desirable to more thoroughly and accurately define the system, both for the phase equilibria and the thermodynamic properties. I) EXPERIMENTAL PROCEDURE A Sieverts&apos; apparatus was employed to conduct the experimental measurements. Briefly, it consisted of a source of pure hydrogen, a precision gas-measuring buret, a heated reaction chamber, a mercury manometer, and two McLeod gages (a CVC, GM 100A and CVC, GM 110). Pure hydrogen was obtained by passing hydrogen through a heated Pd-Ag thimble. The hydrogen was analyzed and found to have only a trace of oxygen and nitrogen. A 100-ml precision gas buret graduated to 0.1-ml divisions was used to measure and admit hydrogen to the reaction chamber. The reaction unit consisted of a quartz tube surrounded by a nichrome-wound furnace. The furnace temperature was controlled by a recorder-controller to ±1°K. An independent measurement of the sample temperature in the quartz tube was made by means of a chromel-alumel thermocouple situated outside, but adjacent to, the quartz tube near the specimen. Pressure in the manometer range was measured to ±0.5 Torr and in the McLeod range (10-4 to 10 Torr) to ±3 pct. The hydrogen compositions in erbium were calculated in terms of hydrogen-to-erbium atomic ratio. These compositions were estimated to be ±0.01 H/Er. The erbium metal was obtained from the Lunex Co. in the form of sponge. The metal was nuclear grade with a purity of 99.9 pct +. The oxygen content was reported to be 340 ppm and the nitrogen not detectable. Metallographically the structure was almost free of second phase (<1 vol pct). A quantity of sponge was arc-melted for use as charge material. The solid material was compared with the sponge in the pressure-temperature-composition relationships. They were found to be identical. Therefore, sponge material was used henceforth, so that equilibrium could be attained more rapidly. The specimen size was about 0.2 grain for each loading of the reaction chamber. The procedure employed to obtain the pressure-temperature-composition data was to develop experimentally a family of isothermal curves of composition vs pressure. First, a specimen of erbium was wrapped in a tungsten foil capsule to prevent contact with the quartz tube. After loading the specimen, the system was evacuated to less than l0-6 Torr, flushed several times with high-purity hydrogen, and evacuated again ready for the start of the experiment. The furnace was then brought to the desired temperature. A measured amount of hydrogen was admitted into the chamber. Equilibrium was allowed to be attained, the pressure read, and the process then repeated many times until 1 atm of gas pressure was finally reached. Other isotherms were then developed in the same manner. The partial pressure plateaus were determined by another manner. In the solid solution-dihydride region a composition of approximately 1.0 H/Er was selected on the plateau. The temperature was varied throughout the range of interest. At each temperature level, equilibrium was achieved, the pressure read, and the next temperature attained. The temperature was cycled both up and down. In the dihydride-trihy-dride region, the plateaus were determined in the 473" to 651°K range only by heating to the desired temperature and not by both heating and cooling. The data were much more reproducible in this manner. Equilibrium required long periods of time. Specimens were initially hydrided to 2.8 H/Er, so that at the higher

Jan 1, 1969

By AIME AIME

DURING the morning session," on Feb. 17, papers were presented and discussed regarding a recent wire saw installation, cement rock quarry operations, hydration factors in gypsum deposits and the status of the phosphate industry of the West. Oliver Bolvles presided and there were about twenty-five members present. W. M. Weigel&apos;s paper (T. P. 262), "The Application of the Wire Saw in Marble Quarrying," was read by the author. He described the recent installation of the St. Clair Marble Co., near Guion, Ark. Since the use of the wire saw for quarrying is comparatively new and the fact that it has been almost entirely limited to slate quarries heretofore, ?he description and data given in this paper were of much interest.

Jan 1, 1930

By AIME AIME

MONDAY, Feb. 21, evokes memories of the Silver Corridor at the Waldorf to be recalled and reflected upon for time to come when thoughts drift to the Annual Meeting of 1944. Crowded though it was, on occasion there lurked in the mind&apos;s eye a vision of what might have been had the 2886 persons who put in an appearance at one time or another milled around in the lobby of 29 West 39th Street. Some confusion resulted from difficulty in locating meeting rooms, but for the most part everyone found what he wanted. The usual bulletin board of members registered was missing this year and rumor has it that tile Waldorf didn&apos;t approve. Registration broke all previous records with many a busy engineer realizing that the program had something to offer that would be of use in his particular job. It might be noted here that "Arpad" co-operated nicely, previewing spring days on Monday, Wednesday, and Thursday; Tuesday was a bit damp.

Jan 1, 1944

The income of the Institute is derived mainly from dues, advertising in MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1939

The following officers and committee chairmen were elected: Honorary Chairman, Herbert Hoover; Chairman, Elmer A. Sperry, New York; Vice-Chairman and Chair-man of the Executive Committee, John W. Lieb, New York; Vice-Chairman, C. E. Grunsky (Pacific Coast), San Francisco; C. F. Kettering (Middle West), Detroit; Execu-tive Secretary, Maurice Holland; Executive Committee: Gano Dunn, George W. Fuller, Maurice Holland, Frank B. Jewett, John W. Lieb, H. J. McGraw, Calvin W. Rice, W. E. Wickenden, all of New York; Dugald C. Jackson, Cambridge, Mass.; 0. C. Merrill, Washington, D. C.; Charles F. Scott, New Haven, Conn.; Elmer A. Sperry, Brooklyn, N. Y.; Finance Committee. John W. Lieb; Technical Program Committee: D. C. Jackson; Transporta-tion Committee: F. B. Jewett; Entertainment Committee: 0. C. Merrill; Publicity: J. H. McGraw; Promotion and Attendance: George W. Fuller.

Jan 5, 1928

By C. W. Price, G. A. Wheeler

BERYLLIUM has always been a difficult material to prepare for metallographic examination. Severe surface deformation occurs during mechanical grinding and polishing, and a suitable bright-field etchant has not been developed. Certain electrolytic techniques produce satisfactory polishes, but these techniques have not yielded entirely consistent results. Furthermore, they have not provided satisfactory bright-field etches. The purpose of this paper is to describe an electrolytic polishing technique that can also provide an excellent bright-field etch. In addition to the bright-field etch, other advantages of this technique are excellent reproducibility, rapidity, and ease of polishing and etching. Experimental Technique. Specimen Preparation. Beryllium specimens may be either mounted or unmounted for the use of this technique, and the size of the specimens is not important. Specimens with surface areas up to 4 sq cm have been electrolytically polished and etched successfully with this technique. The most important requirement is to provide a good electrical contact to the specimens, preferably on the back of the specimens. When specimens are mounted, a hole is drilled through the back of the mount so that the specimen can be contacted with a probe. Conventional metallographic grinding techniques are used to prepare the specimens for electrolytic polishing. The specimens are ground on silicon carbide papers. Grinding through the usual series of papers down to the 600-grit paper is recommended to minimize the electropolishing time, although successful electrolytic polishes and etches have been obtained by grinding only through the coarser papers. A continuous flow of water is used during grinding to provide lubrication and to minimize contamination. Mechanical polishing is not required because high rates of material removal are achieved with the electrolytic polishing. Polishing. Most of the results reported in this paper were obtained with a "Disa-Electropol", manufactured by Struers Scientific Instruments of Copenhagen, Denmark. Satisfactory results have also been obtained with the conventional beaker technique of electrolytic polishing, however, the conditions applicable to both the Disa unit and the beaker technique will be described. Stainless-steel cathodes are used in both techniques. In the beaker technique, a flat cathode, with an area at least twice that of the specimen, is used, and the specimen is held parallel to the cathode. The distance between the specimen and the cathode affects the quality of the electropolish. This distance is set at about 7 mm in the Disa unit; the same distance produces the best results in the beaker technique. Specimen-cathode distances greater than about 20 mm produce considerable relief, while distances less than 7 mm cause high current densities that are difficult to control. An electrolyte of 2 pct HC1, 2 pct HNO3, and 2 pct HCIOl in ethylene glycol gives the most satisfactory results for both electrolytic polishing and etching. This electrolyte was developed by altering the composition of a similar electrolyte used for electrolytic lapping1 and adding HClOl to improve the etching characteristics of the electrolyte. Variations of from 0.25 pct to as much as 5 pct of each of the acids do not significantly affect the results, but the greatest amount of control and reproducibility can be obtained with the composition of 2 pct of each acid. Generally, lesser amounts of the acids produce lower polishing and etching rates, while greater amounts of acids cause high current densities that are difficult to control.

Jan 1, 1968

By Edward H. Robie

In late November and early December a considerable portion of our time was devoted to obtaining a business manager for Institute headquarters. The advisability of creating such a position was suggested in 1949 in the report of the Johnson committee. In that year, however, the Institute had a deficit of $72,000 so every effort was made to minimize expense. At that time most of the duties that normally would be assumed by a business manager were given to Newell Appleton who became office manager, convention manager, purchasing agent, and assistant to the secretary. So many responsibilities were his that he could not devote the necessary time to all of the many things that needed attention. H. H. Vasoll, representing a firm that made a study of Institute head office procedures early last fall, made a recommendation that "a business manager and controller from outside the present organization" be obtained, who would supervise the work of accounting, addressograph, purchasing, book and journal orders, filing, and mailing depts. He further recommended that Mr. Appleton be made administrative secretary, in which position he would act as head of an "Institute Activities Dept." He would devote his time to convention planning, meeting arrangements, travel accommodations, membership control and promotion, and public relations, and would assist the Secretary on special problems. Thus, Mr. Appleton retains some of his former responsibilities and will take more of the load off our shoulders in the conduct of affairs at Institute headquarters. The rest of his former work will be in the province of the newly created "Business Office Dept." Peter J. Apol is the man finally selected for the post of business manager. He is a young man of 32, a native Michigander and a graduate of the University of Michigan where he received a B.S. degree in business administration in 1940. He then spent three years in the Navy and has the rank of Lieutenant in the U. S. Naval Reserve. Three more years were spent in the U. S. Maritime Service as chief purser, and another year as chief paymaster for the Pope & Talbot Steamship Co. The past four years have been spent as head of the Greenland Construction Co., Greenland, N. H., chiefly engaged in building construction. Mr. Apol will endeavor to increase the efficiency of Institute headquarters operations and remove all possible causes for complaints of individual members. He will coordinate as seems advisable the work of various departments and install such modern business office machinery as seems applicable to our needs.

Jan 1, 1952