Search Documents

By J. Gordon Parr, L. P. Srivastava

DUWEZ1 has shown that pure titanium and pure zirconium transform martensitically during rapid cooling at temperatures about 30° and 15°C re spectively below their To temperatures. Holden et al.2 determined M, temperatures of Ti-Cu alloys by a metallographic technique applied to isothermally treated samples. Their results, superposed on the McQuillan3 version of the partial Ti-Cu diagram are shown in Fig. 1. Sources of metals were: Titanium: Iodide bar; Foote Mineral Co. Ltd. Zirconium: Iodide bar; Foote Mineral Co. LM. Copper: Spectrographic Standard; Johnson Matthey and Co. Ltd. Alloys were prepared by levitation melting under argon to the following nominal compositions:* 0.5, Quenching, at rates to about 8000°C per sec, was performed by cooling in a stream of helium (99.999 pct pure) a 3/64 in. cube of material previously heated by a tungsten coil in a system operating at. 10-5 mm Hg. Cooling rates below 200°C per sec w were obtained by controlling the current to the heater coil. The specimen was supported on a 32 gage Pt, Pt-Rh thermocouple attached through a DC amplifier to an Edin magnetic oscillograph (Model 8082) with a maximum chart speed of 250 mm per sec. Transformation temperatures were read off the oscillograph charts at the location of the beginning of the thermal arrest. The same specimen was quenched several times, and all runs were repeated on new samples. Regular calibrations of the oscillograph against a potentiometer were made between quenching experiments. The criterion of martensite formation was the effect of surface rumpling. Previously polished samples that showed a rumpled surface after transformation are assumed to have undergone martens itic transformation: transformations of a diffusion type produce no surface disturbance, Figs. 2 and 3. Electrochemical measurements were made in a cell described elsewhere4 whose electrodes were the martensitic and the diffusion-transformed materials in the following electrolytes:

Jan 1, 1962

By Elmars Ence, Harold Margolin

The titanium-aluminum system has been investigated in the composition region 0 to 34 pct Al in the temperature range 800" to 1450°C. The phases encountered in this region were: a,ß, TiAl3, The reactions observed are as follows: 13 ; L - 6T. A1, 0 (15 pct Al) + 6 (18 pct Al) - yTi Al (16.5 pct Al) at -1170°C andP (7 pctpct Al) + y (9.2 pet Al) - ah(9 pct Al) at - 1060°C. A eutectoid reaction: y — a +d belm 700°C is postulated. THE Ti-A1 system has been the sub.ect of a number of investigations. Several of these1-3 have indicated extensive solubility of A1 in both a and ß titanium. Ence and Margolin, as a result of work on the Ti-A1-0 system:'5 have shown that the a solubility ofalumi-num is considerably restricted, and found that a compound, Ti2A1 existed in the region formerly designated as Q a This structure was identified as hexagonal with c/a = 0.803. Pietrokowsky confirmed the existence of this phase7 and pointed out that the structure was isomorphous with Ti3Sn.8 Although the existence of Ti,A1 has been confirmed by others,9-12 there has been considerable disagreement regarding the composition and mode of formation. A detailed reinvestigation of the Ti-A1 system has been published by Sagel et al.13 The tentative diagram indicated two phases, a, and e, occurring in the former all a region. The a, phase has the same structure as Ti2A1 and was indicated as having a broad region of solubility. Epsilon, a tetragonal phase, was shown to form within the a, solubility region. AS a result of unpublished work,14 Ence and Mugy3 olin disagreed with the interpretation of Sage1 et al., although some common features existed. The present study was conducted in an attempt to clarify prevailing uncertainties. EXPERIMENTAL PROCEDURE Alloy Preparation—Alloys were prepared from iodide titanium (99.9 pct Ti with less than 0.01 pct Zr) or Bureau of Mines electrolytic titanium (BHN-73) and high purity aluminum (99.99 pct). Alloys were arc-melted in argon or helium atmosphere as 15-g buttons in the composition range up to 34 pct Al. Depending on need, alloys were made in increments varying from 0.25 to 2 pct Al. Up to five 15-g buttons of some compositions were made. Weight losses during melting did not exceed about 1 pct of the charge and chemical analysis revealed that both titanium and aluminum were evaporated. In general, nominal and analyzed compositions agreed within 0.5 pct and therefore nominal compositions were used in plotting the data. Unavoidably, some overlap of composition occurred, particularly where small increments of A1 were used. The small increments were primarily used to obtain alloys which would fall into the narrow a -, r region and this purpose was achieved. In general, the data obtained from Bureau of Mines base titanium and iodide titanium alloys were in agreement. Forging—Both as-cast and forged samples were employed. Samples were heated for hand forging by an oxygen-hydrogen torch to the region 1200" to 1300°C. A titanium anvil and cover plate were used to prevent any iron pick-up and consequent formation of a low melting point compound. Frequent reheating kept the temperature in the desired range. Under these conditions, alloys containing up to 15.5 pct could be successfully forged. To check on the depth of contamination, forged alloys were heated slightlybelow the ß transformation temperature. Metal was removed to a depth below the contaminated surface so revealed, and the subsequent results obtained from these samples agreed closely with those secured from as-cast material. Heat Treatment—Prior to heat treatment, all alloys were vacuum annealed to remove hydrogen. Samples

Jan 1, 1962

By C. M. White

CITIZENSHIP is a rather abstract subject on which a great deal could be said-a subject on which a great deal is said -and still one which too many of us seldom think about and seldom work at. Too many of us engineers and business men have but a vague idea of citizenship. We think that if we go to the polls on election day and obey the laws scrupulously, with the exception of an occasional traffic violation, we are pretty good citizens and are doing our duty by our city, state, and nation. But when you think it over, that's a very passive observance of the important right of counting oneself a citizen of a country. There is nothing very positive in that attitude. There is nothing that indicates that we have sufficient interest to really go out and do a job for the -welfare of our country, forgetting any personal advantages or inconveniences that might arise. In other words, this type of voting-on-election- day, law-abiding citizenship does not keep us awake a single minute; it does not take any particular thought or require the expenditure of any time or energy.

Jan 1, 1939

By T. Prof. Egleston

ALL industrial establishments whose operations depend upon chemical reactions use gases. In the simplest case the oxygen of the atmosphere, heated or not, as the case may be, is used, and in other cases, gases which are produced by a special apparatus of more or less complex composition. The manufacturer depends, for the success of his operations, entirely upon having these gases arrive at the right time, in the proper proportions, at the required temperature. It often requires but a slight variation in their composition to make a given process a success or a failure. In most cases the gas used is formed from fuel, and according as variations in its composition are produced by alterations in the manner of charging the grate, not only different, but often directly opposite, results are obtained. The great industrial question of the present time, and one upon which the prosperity of the world depends, is how to get the greatest amount of useful effect from fuel, whether the caloric is used directly or is transformed into horse-power. In almost all industrial pursuits this translates itself into the question of how to construct a fireplace and its adjuncts in such a way that the heat of the flame and of the products of combustion shall be made to produce a maximum effect. Unfortunately, until very recently, except by comparison, there was no means of ascertaining whether the loss of useful effect was 80, 40, or 20 per cent. of the total amount of fuel employed. It seems now strange that there should have been furnaces so constructed as to produce 20 per cent. of carbonic acid in the fireplace, but this has been proved by analysis to have been true. It does seem incredible that, notwithstanding the immense number and variety of furnaces used for different processes, and the great difference in kind, quality, and quantity of fuels consumed, there should formerly have been used for them all, the same stereotyped fireplace, varied only in its dimensions of height, length, and breadth. It is true that, with a good fireman, excellent effects may be, and have been, produced, but the manufacture is here, as in many other cases, dependent on the intelligence of the workman, a very uncertain reliance for capital to rest upon. The workman, unless he receives a prime for fuel saved, or is fined for excessive use of it, may be said

Jan 1, 1874

By R. W. Armstrong, P. C. Jindal

The hardness dependence on grain size for polycrys-talline cartridge brass and a leaded brass has been measured by Brine11 and Rockwell B testing. In each case, the hardness, H, depends on the average grain diameter, 1, according to: H =Ho + kHl-1/2 where Ho and kH are experimental constants. Diamond pyramid hardness values have also been measured as a function of the indentation size and grain size to give additional information on the nature of the hardness test and the dependence of hardness on micro-structure. The hardness of polycrystalline brass depends on its grain size. Bassett and Davis' demonstrated this as early as 1919 by making Brinell hardness measurements on cartridge brass. Since then, the hardness of this type of material has been measured as a function of grain size by making Rockwell,2'3 Vickers,4 and Brinell5 tests. he hardness dependence on grain size has also been measured for other materials. Angus and summers6 investigated the grain size dependence of the Brinell hardness of polycrystalline copper and a Cu-4.5 pct Sn bronze. In other studies, nickel,? Armco iron,Big an Fe-0.07 pct C alloy,I0 and an 0.39 pct C-12.45 pct Cr stainless steel" have been investigated. In some of the preceding cases, the hardness results have been analyzed to show that the hardness varies with the average grain diameter, 1, according to an l-l\4, l-1/4 or I-2 dependence,11-13 The studies of the influence of grain size on hardness have not been based on any theoretical model. This may be because the hardness of a material is itself a complicated property. However, attempts have been made to correlate, experimentally and theoretically, the hardness of a material with its unidirectional stress-strain behavior.14-l6 On this basis, Hall" proposed that the polycrystal hardness dependence on grain size might follow directly from the Hall-Petch18,19 relation for the grain size dependence of the yield stress. Thus, the hardness-grain size relation was given as: H = Ho + kHl-1/2 [1] where Ho and kH were taken as experimental constants. The relation was applied to the measurements on brass,' copper,6 bronze,= and Armco iron.' More recently, this relation was shown by Armstrong and jindal20 to adequately describe the measurements on cartridge brass made by Bassett and Davis' and Babyak and Rhines.5 In this case, the relationship was taken a step further by independently relating the values of Ho and kH to the values of oyand ky, previously reported by Armstrong, Codd, Douthwaite, and petch21 from measurements of the yield stress dependence on grain size for this type of material. In the present investigation, new Brinell and Rockwell B hardness measurements have been made as a function of grain size for a cartridge brass and a leaded brass. In addition, diamond pyramid hardness values were measured as a function of the indentation size. All these results are applied to a further analysis of the hardness dependence on grain size. MATERIALS AND EXPERIMENTAL METHODS Cartridge brass and a leaded brass were selected for this investigation for two main reasons: it was anticipated 1) that these materials could be cold-worked and recrystallized to a wide range in grain size and 2) that the results to be obtained on these typical industrial materials could be usefully compared with previous investigations. The chemical analyses of the actual materials which were employed are given in Table I. The as-received 1/2- and 3/4-in.-thick plates were given various reductions in thickness by cold rolling. The rolled material was heat-treated at various temperatures between 330" and 850°C for differing time periods from 5 min to 9 hr to achieve a variation in the average grain diameter between 0.0339 and 0.000543 cm.22 During heat treatment, the brass was protected from zinc loss by packing it in chips or foils of the same composition material. Reasonably equi-axed grain structures were obtained in each case. The metallurgical grain sizes of the specimens were determined from measurements of the average linear intercept on a random line. Annealing twin interfaces were not counted along with grain boundaries. The

Jan 1, 1970

By G. W. Thomas

A mathematical tnodel of forward combustion in an oil reservoir is treated in this paper. The model describes a radial system having a vertical section of essentially infinite thickness, all of which is permeable to gas flow. Combustion, however, is presumed initiated over a limited thickness of the total vertical section. In the interval supporting cotnbustion, the mechanisms of radial conduction, convection and heat generation are taken into account. Above and below the burning interval, heat transport in the radial direction is by cottduction and convection. Vertical heat losses from the ignited interval are accounted for by conduction alone. A general solution is presented for the temperature distribution caused by radial movement of the combustion front. The results show that no feedback of heat occurs into the ignited interval when convection and conduction are acting in the bounding media. Peak temperatures are also 5 to 10 per cent higher than in the case where heat transport in the bounding media is by conduction alone. We arbitrarily define vertical coverage to be that fraction of the total ignited interval which is at 600F above atnbient, or greater, at any given time. The radial distance at which the vertical coverage becomes zero is the propagation range of the combustion front. It was found that an increase in vertical coverage results when the oxygen concentration, fuel concentration or gas-injection rate is increased. Moreover, the combustion front can be propagated 10 to 15 per cent further than in the case where only conduction is acting above and below the ignited interval. INTRODUCTION In the theoretical treatment of forward combustion in a radial system, one of the problems encountered is the determination of the transient temperature distributions caused by an expanding cylindrical heat source. Bailey and Larkin' and Ramey' simultaneously presented analytical solutions to the problem assuming heat transport by conduction alone. In a subsequent publication, Bailey and Larkin3 included the effects of both conduction and convection while treating linear and radial models. In this latter work, however, vertical heat losses were largely neglected. Selig and Couch' dealt with a radial model in which both conduction and convection were acting. Only a limiting case involving vertical heat losses was considered, however. Namely, temperatures on the boundary of the bed of interest were set equal to zero. Solutions thus obtained were representative of a system having a maximum vertical heat flux. Chu5 recently treated a more general case in which a permeable bed was considered bounded by impermeable media. Conduction and convection took place within the bed, and only conduction outside of the bed. The effects of vertical heat losses were included in his study. Solutions were obtained by numerical techniques. This paper is an extension of the theoretical work of other authors pertaining to forward combustion in a radial system. In particular, a mathematical model of the process is treated in which heat generation occurs over a small vertical interval of a larger permeable section. In the interval supporting heat generation, and above and below this interval, the mechanisms of radial conduction and convection are also presumed acting. Heat losses from the ignited interval are accounted for by vertical conduction. An analytical solution for the temperature distribution caused by radial movement of the burning front is presented. The effects of certain process variables are indicated and comparisons with Chu's results are made. THEORY To render the mechanism of forward combustion tractable to mathematical treatment, we idealize the problem to the extent of assuming continuous reservoir media possessing homogeneous and isotropic properties. The following additional assumptions are implicit in this analysis. 1. The thermal parameters, i.e., heat capacities, thermal conductivities and thermal diffusivities are invariant with temperature and pressure. Moreover, the bounding media possess the same thermal properties as the bed of interest. 2. The temperatures of the porous media and its contained fluids at any point and at any time are equal. 3. The reaction rate between the oxidant gas and the fuel is infinite. This assumption implies that the incoming oxygen concentration instantaneously goes to zero within an infinitesimal distance, i.e., the width of the combustion zone is negligible. 4. The rate of gas injection is constant and corresponds to the average rate throughout the lifetime of the project. 5. The fuel concentration is constant throughout the volume of rock swept out by the burning zone. 6. There is complete burnoff of fuel. This assumption demands that the rate of propagation of the burning front equals the rate of fuel burnoff. In a radial system, with a

By R. W. Hyde, B. S. Old, S. E. Eaton

INTRODUCTION ONE of the most important problems facing the steel industry at the present time is that of maintaining at a minimum the sulphur content of many grades of steel where sulphur is known to have harmful effects on both quality and yield. The present outlook in this struggle to reduce the amount of sulphur in steel is rather gloomy since the sulphur content of the raw materials available in the United States is gradually rising, with little relief in sight. A flow sheet of sulphur in the steel process is shown in Fig I. The values used here were obtained by averaging coke oven and blast furnace data at No. 5 furnace in Cleveland and are considered typical for high top pressure practice. The sulphur evolved in the blast furnace top gas was obtained by difference and since the amount is relatively small, little significance should be attached to this particular value. From Fig I it is apparent, however, that coals used in the production of metallurgical coke represent by far the largest single source of sulphur in steelmaking. As an indication of the decrease in quality of these coals as regards sulphur content the weighed average annual sulphur analysis of the coals supplied to two different steel plants, since 1925, is plotted in Fig 2.1 The sharp rise since 1940 is strikingly apparent. Another indication of this trend is found in estimates of coking coal reserves. Thus in the case of Pittsburgh seam coals available in Allegheny, Fayette, Greene, Washington, and Westmoreland Counties in Pa. as of Jan. 1937 only 25 pct of the coal reserves would contain less than 1.50 pct sulphur after washing.2,3 Many of these lower sulphur reserves have been seriously depleted in recent years because of accelerated war demands. Still another demonstration of the increasing sulphur content of coals on a country-wide basis is found in a report by the Bureau of Mines4 which shows a steady increase in the sulphur content of coke made in the United States, It should be noted that this increase continues in spite of the wider use of coal washing in recent years. Sulphur occurs in coal in three forms, pyritic (FeS2), organic sulphur, and a small amount of sulphate sulphur (CaSO4), The sulphur is subsequently found in the coke in combination with carbonaceous material of unknown composition and as calcium and iron sulphides: In considering the general problem of sulphur elimination, the Republic Steel Corp. was interested in determining which, if either, of the two major forms of sulphur in coal contributes the greater portion of sulphur to the coke, Since the ratio of pyritic to organic sulphur varies widely in different coals, it was thought that if it could be shown definitely that the major part of the sulphur occurring in coke originates from one of the two major forms of sulphur in the coal, it would then be possible to select with confidence coal which, although high in total sulphur, would yield coke of fairly low sulphur content, Using the new

Jan 1, 1948

By H. H. Rachford, W. P. Schultz

The use of computing machines to solve physical problems has made it imperative to represent physical data in a form computing machines can use. Although curve-fitting is an old and well-practiced art, there still seems to be some interest in questions regarding what methods can be used and why. Even though there are many good references on this subject, it may be of some value to discuss a particular method which has been found to be useful, and to make available the associated tables for its use in the hope that there can be saved a few of the tedious hours necessary to reduce many of the suggested methods to practice. Although a very brief discussion of the mathematical background of the tables is included immediately below, those interested only in their use can skip directly to the section on Use of the Tables. Direct Fit of a Set of Points A frequently encountered problem is: Given data which can be represented by a smooth curve +(x), to find an easy-to-evaluate function F(x), with only a few coefficients, which is a good approximation of +(x) on the interval 0 5 x 5 x,,. Consider F(x) as a linear combination of m + 1 arbitrary, single-valued, continuous, linearly independent functions, f,(x), Ff.r) = a,f,,(x) + a,f,(x) + . . . -+ aifi(x) + If the value of Q(x) is known or can be read from the curve at the points xj: +(x,), +(x,), . . . +(xj) . . . +(x.), and if n = m, then all the coefficients of F(x) can be determined, and F(x,) — +(x,) = 0 for j =. 0, 1, . . . n. This follows from the solution of the set of linear simultaneous equations. +(x<.) = aofu(x,) + aJI(x0) + . . . + a,,f,,(x,) =a, = f,,(x,) + a,f,(x,) + . . . + a,f,,(x,) +(x,,) = a,,f,(x,,) + a,f,(x,) + ... + a,,f.,(x,,) ...........(2) for the coefficients ai. Although the set a, from the solutions of the set of Equations 2 yields an fix) which gives an exact value of $(x,) for the n + 1 points, there is no restraint on ~(xj in the interval xi < x < xj+,. Indeed, if the points +(x,) are not sufficiently smooth, very serious differences may arise between F(x) in the interval and the smooth curve +(x). Least-Squares Fit It has been suggested&apos; that if n is made to exceed m, and the set a, is found to minimize the function the function F(x) is much less sensitive to small errors in +(xi), and usually provides a much better fit to the smooth function +(x). This is known as the best fit in the sense of the least-squares error. To minimize $, set £ = 0,i = 0,1,... iTi,.....(3) The m + 1 equations from Equation 3 are k—n k=n a.^p /,,(a) f,(xt) + a, X A: = 0 k=O k = n k = n k=0 k=0 +(x.) f,(x,),............(4) one equation being obtained for each i = 0, 1, . . . m. Inasmuch as the arbitrary functions f(x) may be evaluated for x,, k = 0, 1, . . . n, and the +(x,) are known values of the curve to be fitted, the simultaneous Equations 4 may be solved for the set a,. Particular Functions Given the functions fi(x) and the set +(xj), the solutions for require evaluating a number of sums of products as well as the solution of an m + 1 order set

Jan 1, 1956

By T. L. Joseph

THE invention of the Bessemer converter process in 1856 added great impetus to the manufacture of steel and is one of the outstanding contributions to process metallurgy. Although the process of refining pig iron by passing air through the molten metal bears the name of Henry Bessemer, it should be mentioned in passing that William Kelley of Eddysville, Ky., worked on the process as early as 1847. Kelley was granted a patent on the process in 1857, inasmuch as he was able to prove priority in discovery.1 After considerable litigation in 1865 the respective interests of Kelley and Bessemer were combined. On Sept. 10, 1856, Robert Mushet of England obtained his first patent on the application of manganese to cast steel. Mushet anticipated trouble in purifying iron by passing currents of air through it. His patent specified that steel made in this way often contained flaws and was red short or cold short. Mushet understood the refining of pig iron into steel well enough to realize the difficulties likely to be encountered from oxidation of the iron. Mushet was not only an inventor but he was also an investigator. He understood the principle of selective oxidation which takes place in the converter process, arid he realized therefore that the remedy for over-oxidation was attainable if a suitable metal could be found at a reasonable cost and in sufficient quantities. His first experiments were made in small crucibles holding a few ounces of metal. Later his work was conducted on a larger scale and with complete success. Manganese had been used in making steel a quarter of a century before the converter

Jan 5, 1927

By R. M. Caves

High-purity dense tungsten coating is obtained by means of a modified de Boer-van Arkel iodide process using tungsten bromides. The all-glass reaction system is pumped, baked, and sealed (pinched-off) at about 10-7 mm Hg pressure. The bromides then formed in situ are decomposed, depositing tungsten on heated tungsten surfaces. Heating of the specimen is done inductively in a novel arrangement that avoids electrodes of glass-to-metal seals. The tungsten, deposited at specimen temperatures from 2000° to 2800°F and bulb (halide) temperatures of 225" to 725°F, was adherent and uniform, and ranged in thickness to 1/8-in. REFRACTORY metals are of interest at NASA for use in hypersonic aircraft, in rocket engines, and in other thrust devices where very high temperatures are encountered. Tungsten, with a melting point about 6100° F, is potentially very useful for some of these applications. Considerable research on tungsten and its alloys is currently being conducted at the NASA Lewis Research Center. In this tungsten research program, there is need for a method of depositing high-purity, nonporous tungsten coatirlgs. Metallurgical bonding of the coating both to itself and to the substrate is required. In addition, it is necessary to be able to deposit thin, uniform coatings on substrates of a variety of shapes and sizes for laboratory test purposes. A survey of the methods previously used for depositing tungsten coatings indicated that none would likely meet these requirements for high purity, good uniformity, and high density except thermal decomposition of the halides. The method for coating that was selected for investigation was the thermal decomposition of tungsten bromide. This is a variation of the van Arkel and de Boer iodide process established years ago and recently reviewed.1,2 This process is applicable to the transition metals in general. More recently, the application and techniques were extended with chlorine3 and fluorine,4 and included the coating of tungsten. This is believed to be the first report on the use of the bromide for tungsten coating. Bromine was chosen over the other halogens because it promised a lower temperature for tungsten

Jan 1, 1962

By R. A. Stauffer

The chief ore of lithium is spodumene, a lithium-aluminum silicate containing up to 3 pct lithium. The preparation of lithium salts from spodumene is costly because of the low concentration of the metal and the difficulty of separating it from the other alkali metals present. Dr. Kroll&apos;s and Dr. Schlecten&apos;s recent paper1 has reviewed various methods proposed for preparation of lithium. It will be seen from this paper that the methods proposed to date have required one or another of the lithium salts as a raw material. The high cost of these salts has been the chief item of expense in the lithium metal produced. This situation has made it interesting to investigate the possibility of producing the metal directly from spodumene. When spodumene is calcined at 1000ºC in the presence of lime, lithium oxide is replaced in the ore as is evidenced by the fact that it may be leached from the reaction mixture with water.2 Free energy calculations suggested that lithium oxide might be reduced with aluminum or silicon and the lithium produced distilled from the reaction mixture by heating-to about 1000ºC in a vacuum. These facts taken together suggested that it might be possible to prepare lithium metal directly from spodumene by heating a mixture of the ore, lime, and a suitable reducing agent in vacuum and distilling off the lithium metal as formed. The Replacement of Li2O in Spodumene A series of experiments were undertaken to determine the ratio of lime to spodumene necessary to free substantially all the lithium oxide Present in the Ore. The spodumene used in these experiments was supplied by Foote Mineral Co. in the form of powder of about 200 mesh&apos; Analysis of the spodumene was as follows: PCT SiO2......................... 62.7 Al2O3........................ 29.9 Li2o......................... 4.9 Na2O........................ 0.89 CaO......................... 0.75 MgO........................ 0.49 K2O......................... 0.44 Lime (cp —200 mesh) was added in various ratios to spodumene and thoroughly mixed in a ball mill. Two hundred gram samples of spodumene-lime mixtures were charged loosely in fireclay crucibles and held at 1000ºC in a gas-fired furnace for 5 hrs. The product in each case was ground to pass 140 mesh and then placed in a thimble in a soxhlet extractor. Extraction with water was carried on for 6 hrs. After this period the extract was reduced in volume by evaporation in order to precipitate dissolved lime and was then filtered and titrated with 1/4 normal hydrochloric acid. After correcting for residual calcium oxide in solution, the alkali present was calculated as lithium oxide. The results of these experiments are shown in Table I and Fig I. At lime-spodumene ratios less than 1.5, the products were invariably fused. At the ratio of 1.5 and above, the product was loosely sintered with little evidence of fusion. When the ratio of lime to spodumene was three, replacement of alkali oxides in the

Jan 1, 1949

By G. G. Hancock, H. H. Johnson

Hydrogen gas at atmospheric pressure is shown to cause substantial embrittlement in a martettsitic high-stretzgth steel. Subcritical crack growth is observed at very lom stresses and with high growth rates. It is suggested that an adsorbed layer of hydrogen atoms at the crack-tip surface provides the damaging hydrogen. Oxygen in small quantity, as little as O.7 pct by volume, is shown to eliminate subcritical crack growth in gas environments caused by hydrogen or water vapor. However, dissolved oxygen in water has little or no influence upon crack-growth rates. Oxygen-stopped cracks may be restarted by water, or by hydvogen or water vapor if oxygen is removed from the environment. These observations are interpreted in terms of preferential adsorption of oxygen at the crack tip and the formation of an oxide barrier. RECENT investigations1-3 have demonstrated that environmental factors are frequently responsible for delayed failure in martensitic high-strength steels. The environment causes crack initiation from preexisting cracklike flaws at unexpectedly low stresses, often far below the uniaxial yield strength. The crack then propagates at a rate controlled by the environment and the crack-tip stress-field intensity; during this period crack propagation will cease if either the stress or the aggressive environment is removed, and this may be considered a definition of subcritical crack growth. Fracture occurs when the crack has grown to a critical length, such that the fracture toughness of the steel is exceeded. Several liquids are known to cause delayed failure, but water and water vapor are the most severely damaging of the environments investigated to date.&apos;-3 It has been suggested that hydrogen produced during corrosion reactions may be the actual embrittling agent2 The severe embrittlement caused by water vapor inevitably raises the question as to whether other gas environments are damaging. Previous work4&apos;5 has demonstrated that high-pressure hydrogen (2250 psi or greater) is an effective embrittling medium, as measured by such criteria as reduction in area, notch tensile strength, and time to failure. Moreover, the embrittlement was eliminated by the addition of small quantities of air or oxygen to the high-pressure hydrogen, but it was not influenced by additions of nitrogen or argon.4 In the present study attention is focused upon gas environments at atmospheric pressure, in particular hydrogen and oxygen. The influence of these constituents upon the initiation and growth of a crack from a pre-existing cracklike flaw in a high-strength steel was determined directly by the electric-potential method of monitoring crack growth. MATERIALS AND PROCEDURE The H-11 steel was supplied by the U.S. Naval Research Laboratory as 3 by 12 by 0.065 in. sheet specimens with 1-in. transverse center slots. The slot tips were finished by Elox machining to a radius of 0.001 in. or less. The yield strength was 230,000 psi; chemical composition and heat-treatment schedule are given in Table I. The experimental apparatus, precracking procedure, and incremental loading sequence have been described previously.3 In the only significant change, precracking was sometimes carried out by a hydrogen embrittlement and baking technique. All experiments were conducted at room temperature; the hydrogen gas environment was purified by a commercial palladium purifier. Crack initiation and propagation were followed by the electric-potential method,&apos;-3 using a calibration that has been recently dicussed. Stress-field intensities at the crack tip were computed by the conventional Irwin frmula; the plasticity correction was negligible and therefore not included. EXPERIMENTAL RESULTS A striking brittleness associated with molecular hydrogen at atmospheric pressure is demonstrated by the data in Table I1 and Fig. 1, which indicate that subcritical cracks in hydrogen initiate at lower stress-field intensities and propagate more rapidly than in fully humid argon. Ki and Kf are the crack-tip stress-field intensities at initiation and termination of subcritical crack growth, respectively. Termination, of course, corresponds to fracture. In both hydrogen and humid argon Ki is less than Kf

Jan 1, 1967

By John Rear Admiral Edwards

Introductory.-There are many interesting and important events connected with the petroleum problem. The remarkable men who conceived the thought of transporting petroleum by pipe line, conserving the by-products of the commodity, and conducting extended investigation and research whereby the flash point of the oil was raised, its cost reduced and its Supply assured, are deserving of the gratitude of this nation. It was primarily the success attained by Captain Lucas, after his comprehensive search for oil in Texas and Louisiana, that was the impelling cause. which &apos;prompted the Navy Department to conduct the extensive series of liquid fuel-oil tests that were made from 1901 to 1903. The sensational discovery of oil at Spindle Top made a deep impression upon Rear Admiral George W. Melville, then Engineer-in-Chief of the Navy, and the discovery of the vast oil field in Texas convinced him that, within a generation, if not within a decade, crude petroleum was going to play a very important part in warfare, and that the commodity might possibly develop into a necessary munition of war. The United States&apos; Commanding Position as a Petroleum Producer.¬ In the study of the various problems relating to the world&apos;s production of crude petroleum, the position of the United States is one of commanding importance, whether viewed from the industrial or the military aspect. The present yield of this country is practically double that of the rest of the world, and, in view of the productive and prospective fields possessed by various countries, together with the comprehensive and exhaustive search that has been made throughout the world for petroleum, it is extremely probable that this lead will be maintained for the next decade. As regards the character of the crude-oil yield of different countries, America possesses the greater part of the supply that contains a paraffine base, and therefore a considerable portion at least of the American product produces the best illuminant. Of all the crude-oil distillates, kerosene is in many respects the most important, and the Appalachian product for this purpose is favored, particularly in the Far East, above that of any other petroleum yield of the world.

Jan 9, 1914

By S. Beatty

RECENT experimental results&apos; on the superconductive properties of vanadium indicate that the magnetic behavior of the metal is greatly affected by internal strains caused by mechanical work, and particularly by oxygen and nitrogen impurities. These result in an increase in the hardness of the metal such that metallurgists&apos; have used hardness as a measure of the impurities. An increase in the impurities should also be reflected in a change of lattice parameter with increasing impurity content. The lattice parameter of vanadium prepared by the thermal decomposition of the iodide has been determined by two workers. Neuburger3 obtained a value of a, =3.0338 ± 0.0003A for the body-centered cubic lattice by means of the powder method. The work of Katelaar is referred to by van Arkel4 in which a value of a0 = 3.025 is given. Four samples were used for this investigation. Sample A, the vanadium of the highest purity in the group, was obtained by means of the thermal decomposition of vanadium diiodide and deposited on a 3 mil diam tungsten filament in the form of crystals. The second sample, labeled B, was obtained by the calcium reduction of the pentaoxide at a sufficiently high temperature to give a melt. A third sample, C, was obtained in the same manner as B but remelted in a pure argon atmosphere. The last sample, D, was prepared by the calcium reduction method and the fine powdered vanadium was then sintered by means of applied heat and pressure. Samples A, B, and C were thus essentially free of mechanical strain in their preparation. Sample D was annealed in a high vacuum at 800°C. The samples were prepared for X-ray diffraction analysis such that all additional strain by cold work or by contamination with oxygen and nitrogen was kept at a minimum. Powder obtained from filings was deemed unsuitable since this would require annealing to get rid of the cold work. A heat treatment up to 1000°C at 10-6 m pressure might still increase the impurity content by means of adsorbed oxygen from residual gas in the vacuum chamber. The most satisfactory samples were prepared for back-reflection film techniques. Samples were cut to size, etched with hydrobromic acid, and mounted in Bakelite. They were then lightly polished on 3-0 paper and lightly etched. Chemical and Hardness Analysis of Samples Spectrographic analyses were made of the four samples and indicated similar metallic impurities for the group. The major metallic impurity in each sample was iron, which was less than 0.01 pct. The sum of the other metallic impurities was approximately 0.1 pct. The carbon content was assumed low by virtue of the methods of sample preparation. The principal impurity difference between the samples was in the oxygen and nitrogen content.

Jan 1, 1953

By Edward A. Loria

Vanadium is one of the materials being considered for use in fast-breeder nuclear reactors. It is a good heat conductor and nearly transparent to radiation, properties regarded as ideal for nuclear fuel containers. The problem has been the metal lacks ductility needed for forming. In our program at Reno Laboratory the effects of the U.S. Bureau of Mines (previous affiliation) the effects of oxygen, nitrogen, and carbon have been reported21,22 nd most recently the effects of boron and boron with carbon.23 The continuing study by the Ames Laboratory of the effects of hydrogen, the most subtle and fugitive element in its relationship to structure and properties, is commendable. The solubility of oxygen, nitrogen, and hydrogen in vanadium (and other bcc metals as well) is related to material purity. With the available limit on metal purity and the interaction (clustering) of hydrogen with the other interstitial and substitutional elements present in their base metal, would the authors comment on the tolerance of hydrogen in relation to oxy- gen that will avoid intergranular fracture and above what content or how seriously harmful in oxygen at various carbon levels? Understanding the true effects of hydrogen (and other interstitial impurities) in vanadium depends on knowledge of the amount present under various conditions and its distribution between various possible positions. Significant amounts of hydrogen may be in "thermo-dynamic" solution, but not as individual atoms in interstitial positions. It may be in grain boundaries, in subgrain boundaries, in vacancies, or in dislocations. Some of the hydrogen may be paired or in complexes with impurities in substitutional solid solution in vanadium. This makes the analysis of the effect of hydrogen vastly more difficult. It should not be expected that hydrogen in grain boundaries will affect slip in the same manner as hydrogen in interstitial positions, nor will the complexes react to heat treatment the same way as hydrogen in dislocations. It is gratifying that the authors have quoted results from two of our inestiations,&apos; but neglected one2&apos; which applied the Petch theory to electrorefined vanadium of high purity and analyzed the effects of oxygen, nitrogen, and carbon on the ai and ky values obtained by the extrapolation and grain size methods. Details can be found in the paper. Briefly, we obtained a ui value of 10,300 psi (t = 5150 psi) at 273°K. The metal also exhibited profuse twinning with high ductility at 123" and 77°K. Nitrogen was more effective than oxygen in increasing ui, the increase being about twice as much for the same impurity level. Carbon additions resulted in only minimal changes in Ui. The corresponding ky increased as oxygen and nitrogen increased, with nitrogen being more effective. Carbon additions resulted in little change. Although the difference in yield strength of vanadium was explained on the basis of the Cottrell-Bilby model of the tearing away of dislocations from the impurity atoms,

Jan 1, 1970

On the Art of Metallography (Howe Memorial Lecture), by F. F. Lucas; Beneficiation of Iron Ore. Abstract of paper by C. E. Williams followed by Round Table Discussion; A Statistical Analysis of Blast-furnace Data, by R. 8. McCaffery and R. G. Stephenson; Air Discharge of Circular Tuyeres, by R. S. McCaffery and D. E. Krause; Open-hearth Steel Process as a Problem in Chemical Kinetics. by E. R. Jette; Carbon-oxygen Equilibrium in Liquid Iron, by H. C. Vacher and E. H. Hamilton; A Thermodynamic Study of the Phasial Equilibria in the Bystem Iron-carbon (Abstract), by Yap, Chu-Phay; Influence of Dissolved Carbide on the Equilibria of the System Iron-carbon (Abstract), by Yap, Chu-Phay; Inclusions and Their Effect on Impact Strength of Steel, I and 11, by A. B. Kinzel and W. Crafts: Method for Electrolytic Extraction of MnO, MnS, FeS and Si02, Inclusions from Plain Carbon Steels, by G. R. Fitterer; Permanent Growth of Gray Cast Iron, by W. E. Remmers; Some Notes on Blue Brittleness, by L. R. van Wert; Austenite-pearlite Transformation and the Transition Constituents, by A. Sauveur; Age-hardening of Austenite, by F. R. Hensel; Transformational Characteristics of Iron-manganese Alloys, by H. Scott; Composition Limits of the Alpha-gamma Loop in the Iron-tungsten System, by W. P. Sykes; Magnetic Properties Versus AUotropic Transformations of Iron Alloys, by T. D. Yensen and N. A. Ziegler; Dilatometric Study of Chrome-nickel-iron Alloys, by V. N. Krivobok and M. Gensamer; Low-carbon Steel, by H. B. Pulsifer; Bright Annealing of Steels in Hydrogen, by F. C. KeUey; Development of Continuous Gas Carburieing, by R. J. Cowan. Transactions, Institute of Metals Division, 1931. 500 pages. Index. Papers and discussions presented before the Division at Chicago, Sept. 22-26, 1930 and New York, Feb. 16-19, 1931. X-ray MetallograpIhy: X-ray Determination of Alloy Equilibrium Diagrams (Annual Lecture), by A. F. Westgren; Suppressed Constitutional Changes in Alloys. by G. Sachs; Texture of Metals after Cold Deformation; by F. Wever. Theoretical Metallurgy: Studies upon the Widmanatitten Structure. I.—Introduction. The Aluminum-eilver System and the Copper-silicon System; by R. F. Mehl and C. S. Barrett; Studies upon the Widmanstatten Structure, 11.—The Beta Copper-einc Alloys and the Beta Copper-alumnum Alloys, by R. F. Mehl and 0. T. Mareke; Application of X-rays in the Manufacture of Telephone Apparatus, by M. Baeyerts; Thermal Conductivity of Copper Alloys. 11.—Copper-tin Alloys; 111.—Copper-phosphorus Alloys, by Cyril Stanley Smith; Thermodynamic Study of the Equilibria of the Systems Antimony-bismuth and Antimony-lead, by Yap, Chu-Phay. Ganeral: Cemented Tungsten Carbide; a Study of the Action of the Cementing Material, by L. L. Wyman and F. C. Kelley; Influence of Casting Practice on Physical Properties of Die Castings, by C. Pack; Fabrication of the Platinum Metals, by C. S. Sivil; Effect of Certain Alloying Elements on Structure and Hardness of Aluminum Bronze, by 9. F. Hermann and F. T. Sisco. The WorkinG oF Metals: Metal Working in Power Presses, by E. V. Crane; Forming Properties of Thin Sheets of Some Nonferrous Metals, by W. A. Straw, M. D. Helfrick and C. R. Fischrupp; Die Pressing of Braas and Copper Alloys, by J. R. Freeman. Jr.; Plasticity of Copper-sina Alloys at Elevated Temperatures. by A. Morris: Directional Properties in Cold-rolled and Annealed Copper, by A. Phillips and E. 9. Bunn; Effect of Combinations of Strain and Heat Treatment on Properties of Some Age-hardening Copper Alloys by W. C. Ellis and E. E. Schumacher; Constituents of Aluminum-iron-silicon Alloys, by W, L. Fink and K. R. Van Horn; Equilibrium Relations in Aluminum-antimony Alloys of High Purity, by E. H. Dix, Jr., F. KeUer and L. A. Willey; Equilibrium Relations in Aluminum-magnesium Silicide Alloys of High Purity, by E. H. Dix. Jr., F. Keller and R. W. Graham; Constitution of High-purity Aluminum-titanium Alloys, by W. L. Fink, K. R. Van Horn and P. M. Budge; Experiments on Retarding the Age-hardening of Duralumin, by E. H. Dix. Jr. and F. KeUer; Aluminum-silicon-magnesium Casting Alloys, by R. S. Archer and L. W. Kempf; Modulurr of Elasticity of Aluminum Alloys, by R. L. Templin and D. A. Paul; Quenching of Alclad Sheet in Oil, by H. C. Knerr.

Jan 1, 1931

By L. Russell Van Wert

DURING an investigation in which the solubility relations of the phases in Muntz metal (60 per cent. copper, 40 per cent. zinc) were under study, certain phenomena that had no immediate connection with the main problem were observed, which were thought sufficiently interesting to study further. Because of lack of time, only a preliminary survey was made of two of these; namely, the cleavage structure developed under certain conditions in a 60:40 brass and abnormal grain growth in this alloy. CLEAVAGE STRUCTURE IN HEAT-TREATED MUNTZ METAL Carpenter noted many years ago that cold-working a brass of the Muntz metal type, which had been quenched previously from within the beta field, results in a partial breakdown of the supersaturated beta solution and the precipitation of the solute (the alpha solution) in the cleavage planes of the beta grains. This manner of rejection of a solute from a metastable solid solution is not peculiar to this particular alloy, for among others, it occurs in the cold-working of certain austenitic steels; for example, the austenitic nickel steels. In these ferrous alloys, cold deformation produces a partial decomposition of the austenite, with the formation of martensitic "needles" and zigzags in the austenitic poly-hedra. It is interesting to note that while the two solid solutions-austenite and quenched Muntz metal- are metastable and in their mode of decomposition behave quite alike when deformed in the cold, the metastability of each results from a different cause; viz., that of the austenite from the fact that it is a supercooled solution (its solvent, gamma iron, at ordinary temperatures is below its normal stable range) whereas the metastability of the quenched Muntz metal is the result of supersaturation.

Jan 1, 1929

By Robert Wamsley, W. E. Jones

One of the earliest problems in the life of any community is the provision of an adequate supply of water sufficiently free from all types of contamination to be suitable for domestic purposes. Generally speaking, the location of most communities is determined to a great extent by the availability of an adequate supply of satisfactory water. For a mining camp, that consideration cannot be foremost. Here, the ore takes first place, and the men who mine it must do the best they can under the existing conditions. If there is no local source of water, it must be brought from some distant source or must be found by sinking shafts or drilling wells. Fortunate indeed is the mining company that discovers a commercially valuable ore deposit beside a never failing creek full of pure water, with sufficient water rights available. because the acquisition of water in any other manner nearly always involves not only a considerable period of time but the expenditure of considerable money. The experience of Climax Molybdenum Co. demonstrates the measures that sometimes are necessary in order to provide a suitable supply of water. The Climax mine and mill are on the Continental Divide! about 13 miles northeast of Leadville. The elevation of the domestic part of the camp varies from a minimum of 11,320 ft. to a maximum of approximately 11,550 ft. above sea level, and, as is common at such altitudes, the near-by streams that might be suitable for a water supply are small and intermittent, usually flowing only during the summer months. The only streams of any size in the immediate vicinity of Climax are the Ten Mile and Arkansas Rivers The headwaters of Ten Mile River are on the Company&apos;s property, and its water has been used for the domestic supply. The headwaters of the Arkansas River are about 2 miles distant and have not been used as a source of supply by the company. During the past 11 years of the production of molybdenum at Climax, the number of families living there has increased from about 45 to 283, and the population has increased from about 200 to 1200 persons. Consequently, the capacity of the water-treatment facilities, and the amount of water available, had to be increased to meet the requirements of the camp. As early as 1932 it was recognized that the water in Ten Mile River would not continue to be adequate for domestic purposes and after considerable discussion it was decided to drive a drift through the major fault in an effort to find additional water. This drift was completed in 1935 and tapped sufficient water to make the supply adequate. This water was treated in a tank underground, where lime was added, and was then piped into the domestic supply lines. At about the time this line was completed, the presence of fluorine in harmful concentrations was discovered in the water. This problem was submitted to the International Filter Co. and in November 1937 a plant of its design was put in operation for treating the water to remove the fluorine. This plant proved entirely successful,

Jan 1, 1946

By John E. Caffrey

The Federal Coal Mine Health and Safety Act of 1969, Title III, Interim Mandatory Safety Standards for Underground Coal Mines, is devoted to protection of workmen from hazards of electricity, roof, ribs, fire, and explosions. The Rules and Regulations, promulgated through the Federal Register, provide the criteria by which the law would be administered. Certain aspects of the law involve features that could be summarized under entrapment. These are sections 303 (y)(1), (y)(2) and 317 (f) (4). This paper is intended through the use of the figures to describe how these features of the law affect mine ventilation design, what are the problems, and possible solutions to them.

Jan 1, 1974

By H. R. Page, A. E. Jr Lee

From the inception of zinc retorting on a commercial scale in the United States in 1890,&apos; the retort employed has undergone wide variations in its composition and manufacture, facilitating in part equally remarkable improvements in furnace capacities. The early day hand made clay retort was charged with carbonates or silicates or with coarse dead roasted concentrates mixed with a large proportion of charge fuel resulting in a relatively low zinc burden and fired 24 hr in direct coal fired furnaces. Its modern counterpart is fabricated in hydraulic presses from clay mixtures containing sizeable amounts of either silicon carbide or silica flour, charged with sintered flotation concentrates to more than three times the early day zinc burden and fired 24 to 48 hr in gas fired furnaces. This paper does not attempt to describe in detail the early day clay retort practice as it is well outlined in treatises by Ingalls,2 Lodin,3 Liehig,4 Hofman5 and others. A brief review of clay retort practice is presented together with a description of the major developments since 1912. Clay Retorts The Belgian type retort, both in the circular and elliptical forms, has been used almost exclusively. Typical dimensions of press made clay retorts around 1910 are shown in Table 1. Variations in these dimensions were used at different plants according to local conditions to a maximum inside diameter of 9 in. and inside length of 54 in. However, the effective heat penetration in a 24 hr firing cycle and the tendency of the retort to bend limited the retort size. Use of the elliptical vessel was an attempt to present a stronger cross-section resisting the tendency to bend and to increase the burden without increasing the depth of heat penetration. One exception to the 48-54 in. length was the 60 in. retort used as early as 1905 at Palmerton by means of supporting the last 12 in. at the butt end with a specially designed furnace back-wall. This backwall construction with the 60 in. retort had been developed and used at Bethlehem by G. G. Con-vers and A. B. DeSaulles. An attempt was made at Blende, Colo. to use even larger retorts of the Rhenish type based on European practice and requiring much higher furnace temperatures. Satisfactory plastic clays capable of withstanding these temperatures were not available, and the plant never operated successfully. PREPARATION OF BATCH Composition of the clay retort by weight was 40 to 50 pct raw clay and the balance "grog." Generally speaking the mix consisted of 7 parts plastic clay to 9 parts grog by volume. Principal source of the clay used was the Cheltenham vein—sometimes referred to as "St. Louis city clay." A typical analysis was A12O3-31.0 pct, SiO2-50.0 pct, Fe2O3-2.5 pct, MgO-0.3 pct, CaO-1.5 pct and loss on ignition 14.0 pct. At the smelter the clay was weathered whenever possible and then crushed to 0.08 in. or finer. Grog consisted of calcined adobies, cleaned retort scrap and cleaned refuse fire brick such as old furnace brick, blast furnace linings, and others. Saggers from ceramic plants and calcined flint clay were later used. The grog materials were ground to 0.12 m. or finer. Occasionally coke dust up to 10 pct of the mix was substituted for a part of the grog following European practice.² Particle size of the grog has a major influence on the retort properties—the larger the grain, the better can the retort withstand thermal shocks, resist bending at furnace temperatures and resist corrosion from slag; the smaller the grain, the lower the loss of zinc vapor through the retort walls. Grog forms the skeleton of the retort, and the clay shrinks around its grains to act as a binder. In the drying process, the grog has a stabilizing effect on the drying rate, decreasing shrinkage and giving up previously absorbed water to the surrounding clay to minimize the danger of cracking or checking.² Grog and clay were mixed through a horizontal pug mill with 10 to 20 pct water added, depending on whether the retort was to be formed by hand or mechanically, more water being required for the hand process. The batch or "mud" extruded from the pug mill was cut in convenient lengths for handling, stacked in piles or in special rooms, covered with wet burlap and allowed to "rot" or age from 1 to 8 weeks to increase plasticity. HAND MOLDING If the retort was to be molded by hand, the mud was repugged after the rotting period and given to the molders. Their molds consisted of 3 sheet iron or wood cylinders, each one third the retort length and defining the outer shape of the retort. Beginning with the bottom section, mud was placed in the form and tamped with a rammer

Jan 1, 1950