Search Documents

By Ming-Kao Yen

A considerable amount of work has been reported in the literature in regard to the texture and earing behavior of copper strip. The rolling texture of copper has been confirmed as (110) [112] and (112) [111], which yields ears of a drawn cup at the position 45" from the rolling direction.1-3 The recrystallization texture has been established as the cubic or (100) [001] texture, where the earing positions are at 0" and 90" to the rolling direction.4-8 It has also been reported that in the development of cubically aligned grains of copper strips, the percentage of this cubic texture increased with an increase of final reduction and final annealing temperature.8,9 A comprehensive study on H.C. copper (British commercial copper of high-conductivity quality = Cu 99.95 pct, O2 0.03 pct, Ag 0.003 pct, Fe 0.005 pct and Pb < 0.001 pct) was made by Cook and Richards.6 They concluded that the recrystallization textures could be described as one or more of the following textures: (1) a single texture (100) 10011, (2) a twin texture (110) [112] and (3) a random orientation, depending upon the previous history of the specimen concerned. The effect of various alloying additions in copper was reported by Dahl and Pawlek.10 They found that certain alloying additions, such as 5 pct Zn, 1 pct Sn, 4 pct Al, 0.5 pct Be, 0.5 pct Cd, or 0.05 pct P suppressed the formation of cubic texture. Brick, Martin and Angierll reported that the cold rolled textures due to various additions fitted a rather simple pattern. However, the recrystallization textures were subject to very considerable variations. In the discussion of this paper, Baldwin stated that deoxidized copper containing 0.02 pct P gave a complicated recrystallization texture at lower temperature. When this copper was annealed at high temperature, a single texture appeared which was described as (110) [ill] but. according to a pri- vate communication from Baldwin, this orientation reported was in error and should have been reported as (110)[112]. He also reported that the earing positions of drawn cups were at 60" to the rolling direction.12 Recently, Howald, in his discussion on the paper by Hibbard and Yen,13 reported that the rolling texture of phosphorus deoxidized copper, containing from 0.006 to 0.020 pct phosphorus, was of the pure copper type. When these coppers were annealed at lower temperatures, they exhibited a random orientation, and when they were annealed at higher temperatures they had a mixed (111)[110] and (100)[001] texture, depending on the severity of the final reduction and annealing temperature. However, the specific influence of phosphorus and other impurities on the recrystallization textures and the deep drawing properties of copper strip has not been thoroughly reported. Therefore, an attempt has been made in the present work to determine the rolling and recrystallization textures and also the earing behavior of five types of commercial copper and thereby to evaluate the effect of phosphorus and some other significant impurities on the development of texture for cold reductions of about 87 to 89 pct. Materials Used The five types of copper employed in the present investigation were two phosphorus deoxidized coppers of different phosphorus content (0.007 and 0.013 pct P), an oxygen-free copper (OFHC), an electrolytic tough-pitch copper, and a fire-refined tough-pitch copper. These materials were subjected to a thorough spectroscopic and chemical analysis. The designations and the chemical compositions were as shown in Table 1. The coppers, FA1, FA2 and FA3. were hot-forged from 3-in. billets into a ½ X 6-in. plate and cold rolled to the ready-to-finish gauge indicated below. FA4 and FA5 were hot rolled and scalped to ready-to-finish gauge. The grain size of all the materials in the ready-to-finish condition was about 0.030 to 0.045 mm. Table 2 shows the last stage of the production schedule for each copper strip used. Experimental Procedure ANNEALING, GRAIN SIZE AND HARDNESS DETERMINATIONS Specimens of each type of copper were finally annealed in air for periods of one hour at temperatures ranging from 300 to 1600°F and were subsequently cooled in air. The average grain diameter of the annealed specimen was estimated by comparing with a standard grain size chart. Hardness was determined on the Rockwell 15 T scale. CUPPING TESTS Cups were made in a blanking and drawing set, in which blanks of 2-in. diam were drawn to a cup of 1.25-in. diam with an average depth of about 0.75 in. The clearance between the punch and die was about 0.032 in. The ears of the cup were measured with a special fixture which read the height of ears to one-thousandth of an inch on every ten-degree interval along the circumference of the cup. POLE FIGURES The usual transmission diffraction method with unfiltered copper radiation was employed to determine the pole-figures of the specimens cold-rolled or annealed at 900°F. All the pole-figures were derived from the positions of intensity maxima on 111 diffraction rings of the X ray photo-grams taken at 10 rotation of a

Jan 1, 1950

By R. A. Irvine

The use of large vibrating screens presents unique challenges to the screen manufacturer, the plant designer, and the plant operator. The design of vibrating structures that span greater unsupported distances is critical to the reliability of a screen subjected to billions of fatigue cycles. Larger percentages of total plant production become dependent upon fewer, larger vibrating screens. Plant designers and operators must plan for equipment maintenance in a manner which optimizes the production availability of large vibrating screens.

Jan 1, 1985

By W. C. Ellis

For the purpose of developing combinations of higher strength and conductivity than are obtainable by heat treatment alone in the age-hardening copper alloys, an investigation has been made of the effects of combinations of heat treatment and strain hardening on the properties in question. The investigation was limited to a study of the alloys containing nickel and silicon; nickel, silicon and cadmium; and cobalt and silicon. The experiments made in the course of the study are described in this paper in three groups: 1. The effect of hard drawing subsequent to heat treatment on the mechanical and electrical properties of the alloys. 2. The effect of low-temperature aging on the properties of heat-treated and hard-drawn alloys. 3. The effect of strain on the rate of aging of quenched nickel-silicon-copper alloys.

Jan 1, 1931

By T. Sterry Hunt

Jan 1, 1891

By E. A. H. Tays

At the present time, the mine-owner has a number of patent crushers to choose from, when contemplating the erection of a mill; and a number of new ones are yearly brought to notice. We all know that the stamp-mill is the old standard; but several of the patent crushers, especially of the roller-type, are not without their merits. Having had a working experience, extending over a period of four years, with the " Bryan roller quartz-mill," working alongside of stamp-batteries, I take pleasure in giving to the members of the Institute the benefit of my experience with this mill.*

Jan 1, 1900

By AIME AIME

ON the headwaters of the Hudson Riser, in a sparsely populated area of the north woods at Tahawus, N. Y., thirty miles from the nearest railroad, is the Maclntyre property of National Lead Co. Operations involve the mining and processing of titaniferous iron ore to produce ilmenite concentrate, and magnetite concentrate containing vanadium, for use in the production of iron, titanium, and vanadium in the war program. Accordingly, Maclntyre at present is classed as a war plant. More than 3000 long tons of ore is ruined daily by opencut methods and treated in an ore concentrating plant.

Jan 1, 1943

By J. R. McWilliams

Several of the current concepts of brittle fracture involve consideration of the existence of defects or flaws. Griffith 1 observed that the tensile strength of brittle materials was several orders of magnitude less than might be expected from the calculated strength of the molecular bonds. He was able to show that the stress concentration at the tip of an elliptical crack is sufficient to raise the local stress level many fold. He therefore proposed that real materials do contain such stress risers in the form of minute cracks and that this accounts for the rather large difference between theoretical and actual strengths of brittle materials. The degree of stress magnification depends to a great extent upon the orientation of the crack with respect to the general stress system, and to the general geometry of the crack.

Jan 1, 1967

By W. C. Knoblaugh

ROTARY kilns are adaptable to many fuels, but this paper deals principally with the use of powdered coal. The observations and conclusions presented are based on rotary kilns used in the manufacture of basic refractories for steel furnaces. Solid fuels are pulverized for two principal reasons: (I) ease of control, and (2) rapidity of combustion. By the use of pulverized coal, the operator can increase or decrease the fuel supply by small increments and with very little time lag between the change of control and the resultant change in the flame. This is extremely important in this type of furnace, as the temperature range for maturing the clinker is very narrow. By fine grinding, it is possible to increase the rate of burning of the coal, thereby liberating great quantities of heat within a small space in a short time. Under given conditions, temperature is a measure of the heat liberated per unit of time. To attain the temperatures of 2950° to 3150°F., which are encountered in the manufacture of various steel-furnace refractories, it is estimated that it is necessary to liberate 125,000 to I75,000 B.t.u. per cubic foot of the burning zone per hour. The manufacture of dolomitic refractories is a ceramic process and, as is true in most such processes, the material must be subjected to a certain critical temperature for a certain length of time in order to complete the reaction. If the time of reaction is reduced, the temperature must be increased; in other words, if the rate at which the material flows through the hot zone of the kiln is increased, the temperature of the hot zone must be increased to compensate for this shorter exposure to the flame. FIRING WITH PULVERIZED COAL Fig. I is a line drawing of a rotary kiln with the attendant equipment indicated in their relative positions. The kiln proper consists of a sloping, refractory-lined steel tube rotating slowly about its longitudinal axis (0.75 r.p.m.), and is countercurrent in operation in that the raw feed is introduced at the stack end and gradually approaches the zone of highest temperature at the lower end, where the fuel is introduced. Before 1930, the usual method of firing a rotary kiln was to store the coal in the pulverized form and then feed from this storage to the kiln as needed. This proved unsatisfactory and dangerous because of dust explosions and the inability to obtain an even feed to the kiln caused by arching of the coal in storage and flooding of the coal feeders. In later years the practice has been to store the raw coal and grind it as it is needed. Such a layout is indicated in Fig. I. The coal is stored in bins, charged from the top and drawn from the bottom into recording scales and then into some type of unit pulverizer. There are a number of good pulverizers on the market, each incorporating features that the manufacturer considers outstanding.

Jan 1, 1946

By R. V. Ramani, George W. Luxbacher

Computer simulation of mine ventilation systems, after a slow start in the early sixties, is gaining increasing acceptance for planning, design, and evaluation purposes. Numerous programs are readily available from government, university, consulting, and industry sources. The computer adage "garbage in, garbage out" is as applicable in ventilation engineering as in any other application of computers, and has been responsible for the questionable results obtained in some instances. The source of input data for a ventilation simulation is most often a pressure-quantity survey of the mine, or, in the case of a new mine, information derived from a survey of an existing mine which has conditions similar to those expected in the new mine. The crucial step is to generate simulation input data from the ventilation survey. Problems such as quantities that do not balance, pressure gradients opposite to measured air flow, differences in the pressure datum in a multi-shaft mine, modeling of leakage, and deviations in flow from the square law (H=RQ2) are frequently encountered and must be resolved. The purpose of this paper is to discuss these aspects and to propose procedures which can lead to input data for valid simulations of mine ventilation systems.

Jan 1, 1982

By C. M. Myrick

(Cleveland Meeting, October, 1912) THE following notes are submitted in the belief that they may interest some of the many owners of small water-power plants, so generally used in mining-work throughout the West. A small and somewhat primitive quartz-mill was taken over by a leasing company, and a 10-stamp battery was installed. Originally, power had been furnished by a Pelton wheel ; but, since the supply of water depended on the rate at which snow was melting on the mountains, a steam-plant had been added to help out during cold spells. This auxiliary plant was antiquated and expensive to operate, and, soon after starting up the remodeled mill, it broke down completely; so that it became necessary to get all the power possible out of the Pelton wheel,. with its ever-varying water-supply. The pipe-line, about a quarter of a mile long, was made up. of assorted sizes, from 7 to 11 in. in diameter; and, since it was buried deep under snow, there were no data from which to calculate the theoretical size of the nozzle. The stream being at this time at a low stage, it was important to make the most efficient use of the available water. This was done by using a nozzle large enough to pass the whole supply-taking care, however, to limit the size so as not to lower the water-level in the tank at the head of the pipe-line. As the weather became warmer, the nozzles were gradually enlarged to meet the increasing volume of water; but a point was finally reached where further enlargement only gave decreased power. Evidently the loss from friction had more than balanced the gain from the increased flow through the pipe. However, the area of nozzle that developed the, maximum power from the pipe-line had been found. This was used; and the surplus water was allowed to run to waste at the head of the line.

Oct 1, 1912

By AIME AIME

IN ACCORDANCE with the provisions of the Rules of Procedure of the American Engineering Standards Committee, the American Society for Testing, Mate-. on Feb. 15, 1921, submitted for approval by the A. E. S. Committee certain Standard Specifications for Copper, all of which were adopted or in process prior to Jan. 1, 1920, and sent with the standards the following histories of development and statements of use. FOR SOFT OR ANNEALED COPPER WIRE (B3-15) These specifications were originaly adopted by. the American Society for Testing Materials in 1912. They were prepared by a committee of the Society designated as Committee B-1 on Copper Wire. The committee consisted of eleven members; representatives of five manufacturers of -copper wire, of four manufacturers of electrical apparatus, and of two firms of consulting and contracting engineers. The members of the committee were designated by the officials of the companies to act as their representatives in the committee.

Jan 1, 1921

By Joseph P. Kittredge

At the time this matter first came up in 1912, the National Malleable and Steel Castings Co. had seven basic-bottom open-hearth furnaces in its plant at Sharon, Fa., using fuel oil, then costing about 2½¢ per gallon. The fuel was satisfactory but its cost fluctuated widely, therefore the use of pulverized coal, which had been successful in the cement industry and in some metallurgical furnaces, was suggested. After a thorough investigation, and an actual trial on one of the open-hearth furnaces, to be certain that the siliceous ash in the coal would not seriously affect the basic slags, the management of this company approved its adoption and a complete installation was started. The conclusion had been reached that the success of the operation depended on pulverizing the coal to greater fineness than had thus far been accomplished, and all equipment was chosen with this in mind. A coal drier was deemed essential, and one of ample capacity and efficiency was selected, which has done all that was expected of it, working without failure and with very small maintenance cost, and is still in operation. Pulverizers The company demanded a pulverization of at least 90 per cent through a 240-mesh screen, with consistent results, and a machine was chosen that was grinding other materials than coal to the fineness desired. The control of fineness was obtained through a vacuum separator, and was governed by the size of the separator and the number and construction of the valves necessary to expand and direct the air current. These valves can be set to obtain any degree of fineness desired, and the result is consistent. Two machines were installed, each capable of producing 2½ tons per hour, 95 per cent through 240 mesh. These machines have done everything expected of them, have run continuously, and are still in operation. An examination of some of our pulverized coal by elutriation and microscopic measurement disclosed that a 1-lb. lump of bituminous coal,

Jan 1, 1940

By Joseph P. Kittredge

At the time this matter first came up in 1912, the National Malleable and Steel Castings Co. had seven basic-bottom open-hearth furnaces in its plant at Sharon, Fa., using fuel oil, then costing about 2½¢ per gallon. The fuel was satisfactory but its cost fluctuated widely, therefore the use of pulverized coal, which had been successful in the cement industry and in some metallurgical furnaces, was suggested. After a thorough investigation, and an actual trial on one of the open-hearth furnaces, to be certain that the siliceous ash in the coal would not seriously affect the basic slags, the management of this company approved its adoption and a complete installation was started. The conclusion had been reached that the success of the operation depended on pulverizing the coal to greater fineness than had thus far been accomplished, and all equipment was chosen with this in mind. A coal drier was deemed essential, and one of ample capacity and efficiency was selected, which has done all that was expected of it, working without failure and with very small maintenance cost, and is still in operation. Pulverizers The company demanded a pulverization of at least 90 per cent through a 240-mesh screen, with consistent results, and a machine was chosen that was grinding other materials than coal to the fineness desired. The control of fineness was obtained through a vacuum separator, and was governed by the size of the separator and the number and construction of the valves necessary to expand and direct the air current. These valves can be set to obtain any degree of fineness desired, and the result is consistent. Two machines were installed, each capable of producing 2½ tons per hour, 95 per cent through 240 mesh. These machines have done everything expected of them, have run continuously, and are still in operation. An examination of some of our pulverized coal by elutriation and microscopic measurement disclosed that a 1-lb. lump of bituminous coal,

Jan 1, 1940

By D. L. McElroy

SAFETY in coal mining received especial attention by the public in general and the mining industry in particular during 1940 and early in 1941, owing primarily to the six explosion disasters which occurred last year with a total of 276 fatalities. This was the largest number of fatalities due to explosions in bituminous coal mines since 1928, when 347 lives were so lost. But facilities due to explosions have had a definite decreasing trend since 1907, in spite of bad years such as 1917, 1924, 1932, 1937, and 1940. Although the upswing in explosion fatalities in 1940 is lamented by all, none will admit it represents a trend and it will serve mainly to stimulate ways and means of further reducing these disasters.

Jan 1, 1941

By Arnulf Muan, D. P. Masse

PHASE relations in the system CoO-SiO2 have been determined as a basis for further investigations of thermodynamic properties of olivine solid solutions involving Co2SiO4 as a component. Previous data on the system CoO-SiO2 are incomplete or uncertain. Biltz and Lemke1 determined the melting point of cobalt orthosilicate as 1345°C , but Asanti and Kohlmeyer2 have later found a considerably higher temperature, 1420°C. The latter authors also studied melting relations of one mixture on the CO side and two mixtures on the SiO2 side of the orthosilicate composition and sketched a tentative phase diagram for a limited composition range of the system. However, no phase identification was carried out, and the authors left unanswered the question of the possible existence of a stable meta-silicate phase. Greig3 showed that a 90 wt pct SiO2-10 wt pct Co mixture at 1725°C consists of two immiscible liquid phases. The quenching technique was used in the present investigation. Mixtures of high-purity cobalt oxide ("Fisher Certified") and dehydrated silicic acid ("Baker Analyzed") were equilibrated in air atmosphere. The samples were then quenched to room temperature and the phases present were identified by microscopic and X-ray examination. The samples were kept in small envelopes made from thin (0.0004 in.) platinum foil. Thermodynamic data which have become available recently for Pt-Co alloys4 were used to check that the losses of COO from the oxide samples by alloying of cobalt with platinum in the present investigation were too small to change significantly the compositions of the oxide material during the equilibration. A vertical tube furnace with an 80 pct Pt 20 pct Rh resistance winding was used in runs up to 1510°C. Temperatures in these runs were measured with a Pt vs 90 pct Pt 10 pct Rh thermocouple calibrated against the melting point of diopside (CaMgSi2O6, 1391.5?C). The given temperatures as measured by this technique are estimated to be accurate to *5°C. Quench runs at temperatures above 1650°C were made with a modified Roberts and Morey5 strip furnace, using strip resistors composed of a 60 pct Pt-40 pct Rh alloy. Temperatures were measured with an optical pyrometer which was calibrated against the liquidus temperature of a mixture composed of 10 wt pct CaO, 90 wt pct SiO2 (1707°C). The temperatures measured with this technique have an estimated accuracy of +15°C. The results are shown graphically in Fig. 1. Only one intermediate phase, the orthosilicate Co2SiO4 with olivine-type structure, is stable in addition to the end members cobalt oxide and silica. The melting point of the orthosilicate was found to be 1415" ± 5°C. The metastilicate CoSiO3 is not stable at the temperatures of the present investigation. The two eutectic points in the system CoO-SiO2 where COO plus olivine, and olivine plus silica, coexist with liquid were found to be 72 wt pct COO and 1407°C and 63 wt pct COO and 1381°C, respectively. The melting point of cobalt oxide in air was taken as 1745?C, based on the previous data of Aukrust and Muan.6 Within limits of error (+ 5?C), identical eutectic temperatures to those determined in air were found when two representative mixtures were equilibrated at 1 atm O2 pressure and in an atmosphere of 84 vol pct CO2, 16 vol pct H2. This suggests that changes in oxidation state of cobalt in the condensed phases are not significant as far as their effect on the phase relations are concerned. This inference was substantiated by failure to detect7 any "excess oxygen" (i.e., oxygen in excess of that contained in Co2SiO4) in a sample of orthosilicate composition equilibrated in air 10°C above the liquidus temperature and subsequently quenched to room temperature. This work was carried out as part of a research program sponsored by the U.S. Atomic Energy Commission under Contract No. AT(30-1)-2781.

Jan 1, 1965

TULSA, the host of the Petroleum Division this year, is the oil metropolis of the Mid- Continent and gateway of the Southwest. It has risen in less than three decades from a dusty cattle town of less than 1000 population to its present-day status of a modern, wide-awake and prosperous city of close to 150,000, with an assessed realty valuation of approximately $100,000,000. Oil was discovered near Tulsa in 1901, and with it came th.2 development of the Mid-Continent field, one of the richest in the world. Tulsa from the start has been the center of operations, and its location on foul- and aggressive application of the airplane to oil-field requirements tends to fix this status as production is developed farther and farther afield. That Tulsa is far more than an ephemeral oil town is punched into the newcomer&apos;s- especially the Easterner&apos;s-mind, as he is whisked by taxi from the railroad station to the Hotel Mayo. The cicadalike pounding of the riveters on the steel skeletons of many skyscrapers, mounting upward to fill the gaps in an already well-developed skyline, dispels the feeling of a new atmosphere and puts him back on Forty-second Street, Michigan Boulevard or whatever his own particular "Main Street" may be along which an American city is being remade. Practically every company of any importance operating in the Mid-Con-

Jan 1, 1928

By Charles Catlett

(San Francisco Meeting, October, 1911.) WHILE the occurrence of phosphorus in coking-coal has assumed less importance with the development of the open-hearth method of steel-making, it may not be without interest to note the form in which phosphorus exists in one particular coal-seam. In the examination of what is known as the Big seam, which outcrops a few miles west of Columbiana, Ala., my attention was called to the distribution through the coal, in the form of minute veins and particles, of a resinous-looking substance. A small amount of this was selected, and was provisionally identified as evansite (Al6, P2 014. 18 Aq). Subsequently, through the courtesy of Dr. Sharshall Grasty of the Geological Department of the University of Virginia, I was able to secure an additional amount of material, which was purified down to about 0.3 g. This was examined by Prof. John J. Porter of the University of Cincinnati, and gave the following partial analysis

Nov 1, 1911

The President was authorized to appoint. a liaison committee to cooperate with the American Mining Congress in respect to the establishment of a Secretary of Mines and Mining in the President&apos;s Cabinet. He appointed Edwin Ludlow, Chairman; Mark L. Requa, and J. E. Johnson, Jr. It was resolved to accept the invitation from the Chicago Section to hold the. 120th meeting of the Institute in Chicago during the week of Sept. 15, 1919. The action of the Executive Committee in appointing Past President E. Gybbon Spilsbury as representative of this Institute to visit France upon the invitation of the Société des Ingénieurs Civils de France was approved. The final budget for 1918 was approved. Tile President was authorized to appoint a committee, of three members, on the Development of Activities of the Institute. The committee was requested to report at the February meeting of the Institute, and the Secretary was requested to invite each local section to have a member present to discuss the subject. The President appointed J. W. Richards, Chairman; P. N. Moore, and Allen H. Rogers. Thirty-six members, ten associates, and five junior associates were elected; one change of status from associate to member was granted; two members were reinstated; and eight resignations were accepted. An extension of time was granted to nine members. The dues of eight members were suspended on account of their being in active service.

Jan 2, 1919

By C. E. Lesher

Low-temPeRatUre carbonization needs no introduction to the literature on coal. This paper will attempt no review of that literature; it tells the story of the commercial development of one of the processes for carbonizing coal at so-called low temperatures, dealing with the technology and economics of the process rather than with the design of equipment. The process used is that covered by the patents of C. B. Wisner, with improvements and changes made by the Pittsburgh Coal Carbonization Co. The important and novel feature of the process is the phenomenon of making the product in ball form (Fig. 1). Melting coal dust into smokeless solid fuel in an apparatus as simple as a revolving cylinder of ordinary mild steel has been proved to be practical. Furthermore, it has been found that the process has a wide application, for by applying a knowledge of why and how this balling action is accomplished, the apparatus can be designed and adapted to treat any coal that has a certain minimum agglutinating property. The operating plant is 20 miles west of Pittsburgh, adjacent to the Champion preparation plant of the Pittsburgh Coal Co. The coal used is cleaned minus ?-in. or finer sizes. The products are low-tem-perature coke, tar and tar products. Present capacity is 7000 tons per month of low-temperature coke and 140,000 gal. of tar. There is no surplus gas for sale, and none of the light oils are stripped from the gas. The coke is marketed in two sizes, 1 to 2 in. and 1 to 6 in., through retail coal dealers for domestic consumption in hand-fired furnaces, and for fireplace fuel. The smaller size is bagged by dealers. Crude tar and many distillates and road tars are sold. Acknowledgments During the 10 years in which the work that is summarized in this paper has been under way, many have contributed time and effort, faithful service and fruitful thinking. Whatever success has attended

Jan 1, 1940

By C. E. Lesher

Low-temPeRatUre carbonization needs no introduction to the literature on coal. This paper will attempt no review of that literature; it tells the story of the commercial development of one of the processes for carbonizing coal at so-called low temperatures, dealing with the technology and economics of the process rather than with the design of equipment. The process used is that covered by the patents of C. B. Wisner, with improvements and changes made by the Pittsburgh Coal Carbonization Co. The important and novel feature of the process is the phenomenon of making the product in ball form (Fig. 1). Melting coal dust into smokeless solid fuel in an apparatus as simple as a revolving cylinder of ordinary mild steel has been proved to be practical. Furthermore, it has been found that the process has a wide application, for by applying a knowledge of why and how this balling action is accomplished, the apparatus can be designed and adapted to treat any coal that has a certain minimum agglutinating property. The operating plant is 20 miles west of Pittsburgh, adjacent to the Champion preparation plant of the Pittsburgh Coal Co. The coal used is cleaned minus ?-in. or finer sizes. The products are low-tem-perature coke, tar and tar products. Present capacity is 7000 tons per month of low-temperature coke and 140,000 gal. of tar. There is no surplus gas for sale, and none of the light oils are stripped from the gas. The coke is marketed in two sizes, 1 to 2 in. and 1 to 6 in., through retail coal dealers for domestic consumption in hand-fired furnaces, and for fireplace fuel. The smaller size is bagged by dealers. Crude tar and many distillates and road tars are sold. Acknowledgments During the 10 years in which the work that is summarized in this paper has been under way, many have contributed time and effort, faithful service and fruitful thinking. Whatever success has attended

Jan 1, 1940