Search Documents

and would also contribute to the post-war employment. -As far as the future is concerned, I doubt whether any of the present geophysical methods will ever be developed to directly indicate ore. However, the geochemical methods and certain combinations between chemical and geological methods now used might be the answer to our prayers for direct and more definite methods of determining the quality of the ore or its relative metal content. Geochemical and spectrochemical analysis of minute content in ground waters, in soil or in plants and trees, living or dead, will be extremely important and I would venture to predict that in the very near future each mining or exploration company and each assay oflice will have its own spectroscope equipped for accurate chemical analysis, not only to guide the daily work in the mine, but also for identifying ores as well as for guiding exploration, geological mapping and the evaluation of geophysical indications. These methods, although they are still in their infancy, promise very much for the future. Radioactivity methods could also be helpful when sufficient facilities for radioactivity determination can be made available. They have already been used to a great extent in oil exploration and experiments have shomn great promise for ore exploration also. As for future surveys of large areas, the exploration for physical contrasts will be made from the air, using aeroplanes, helicopters, etc. Already electrical and magnetic methods have been designed whereby the instruments are carried in the aircraft and by automatic recording the location of anomalies is made in a simple enough manner. It should be possible in this way to cover, say, a square mile in an hour. Later Discussion Replies to Dr Lundberg. J. B. Macelwane.*—Someone has said that if a person knows his subject well enough he can explain it in words of one syllable. The point is well taken and I think the converse is also true. If a person cannot explain a subject clearly in simple words, it is either because he has not sufficient command of the language, or he is not master of his subject. Now it is obvious, it seems to me, that the remedy for both of these unfortunate conditions lies not in less education, but in more. If Dr. Lundberg has met geophysicists who confused and discouraged prospective clients by their inability to talk the language of the mine owner or of the mining engineer or geologist, the fault most probably lay in the geophysicist's lack of sufficient training; but it may also have been the want of ordinary common sense, which no amount of education can supply. It is hard to understand the position taken by Dr. Lundberg. Does he regret his own extensive training? noes he wish to say that he would have had greater success in geophysics if he had been only a mine hand with an instrument and a rule of thumb? As a matter of fact, I find it rather difficult to account for his presentation before this Committee on Geophysics of an emotionally distorted picture of the Report of the Committee on Geophysical Education, after the lapse of an entire year since the Report was read and discussed in its proper place, unless he honestly thinks he is handicapped by his knowledge and training and wishes to warn the whole profession against a similar fate. I regret that I am obliged to disagree so emphatically with Dr. Lundberg's thesis— but I believe it would be dangerous if left unchallenged, both because of the inaccurate statements it contains concerning the recommendations made in the Report and because of the ultimate discredit that would be bound to fall upon genuine geophysics if Dr. Lundberg's recommendations were extensively followed out. S. F. Kelly.*-—The argument that a science and its practitioners can be improved by debasing the standard of educational preparation is indeed a strange argument to come from the pen of a man with the education of Dr. Hans Lundberg. In criticising the Committee report, moreover, he has to a certain extent set up a straw man to belabor. The statement that the Committee report recommends that

Jan 1, 1946

By Edgar C. Bain, William E. Griffiths

The results of an inquiry into the structural nature of some 70 iron alloys containing both nickel and chromium over a considerable range of concentration are briefly described in this paper. This study is a part of a comprehensive program of investigation into alloys involving chromium in progress at the Union Carbide and Carbon Research 1aboratories. All the compositions studied contained carbon in amount comparable to commercial alloys. The B Constituent In addition to locating the limits of composition for the three principal types of structure (polyhedral ferrite, martensite and austenite) and their combinations, certain other features of the system were observed. A hitherto undescribed brittle constituent (designated here as the "B constituent") was discovered. It is very hard, non-magnetic and forms in two modes from chrome-ferrite by recrystallization. It is the stable low-temperature condition for the equal-proportion chromium-iron materials containing less than 10 per cent. nickel. Although it partakes of the nature of an inter-metallic compound, yet it may exist over a considerable range of composition. It is non-existent above a temperalure zone, varying with composition, from 800° C. to 950° C., and heating above this critical temperature develops chrome ferrite persistent after average cooling rate; a few hours just below this temperature will develop the complicated brittle crystalline type. The B constituent, when found in the grain boundaries of alloys of lower chromium content, contributes a serious brittleness removable, however, by heating and cooling rapid enough to prevent its re-format'ion. By suitable means of precipitution, the hard B constituent can be made to strengthen the already stiff alloy matrix in the manner of submicro-scopic particles, as exemplified in duralumin or the Sykes iron-tungsten and iron-molybdenum alloys. A possible explanation is offered for the familiar brittleness developed in chrome iron at temperatures above about 475" C. and removable by

Jan 1, 1927

By Frank Gilbreth

THE problem, of the crippled soldier in industry is not a problem of war work only; it is a problem of industrial development. As individuals, each one of you is seeking to provide our maimed heroes with such teaching as will render them, in the shortest possible amount of time, productive and satisfied members of the community. As individuals you are interested in the organizations that are preparing to receive these men, to train them and to place them at that work for which they are best fitted. As an organization, it is now your duty to take up the industrial end of the problem, to investigate existing conditions in the industries, to discover where the opportunities for employment lie, and so readjust industrial practice that the cripples may be utilized to their own and the community's good with the least shock to themselves or to the industries, and with the greatest amount of permanent benefit to all concerned. We have divided industrial opportunities suitable for cripples roughly, into three classes. First, such as already exist in the industries, which can be set aside for cripples only, present occupants being transferred to other work for which they can be fitted but which is not suitable for cripple work; second, opportunities in the industrial world that, through changes in the working equipment or tools, or through appliances attached to the cripple himself, can make the cripple a competitor of the sound worker; third, opportunities not existing at present in the industries, but which could be introduced for the good of the community, without placing the cripples into competition with any existing class of workers.

Jan 4, 1918

By F. E. Buch

THE Smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The Smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter ,aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pct moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pct oxide copper. The predominating minerals are chalcocite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating k bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. GENERAL DESCRIPTION Flotation concentrate, containing to pct moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1947

By Ernst F. Eurich

Alexander Parkes patented in England in 1851-52-53 a process for desilvering lead by means of zinc, making use of the greater affinity of silver for zinc than for lead, discovered by Karsten in 1842. The efforts in England to develop it commercially were not particularly successful, nor was the attempted introduction into the United States. This last was not surprising, as it was about the beginning of our Civil War, and at that period there was very little lead-bullion produced in the United States and there was no field for the process here. There was at that time on Staten Island an establishment that pattisonized lead, probably from Rossie, N. Y., and Chester, Pa., and possibly some Spanish lead, but the production of lead-bullion in the Far West had not yet begun. In 1864, Edward Balbach, of Newark, N. J., patented in this country a process for desilvering lead by means of zinc, and in 1867 Edward Balbach, Jr., patented a " movable black-lead retort with a neck, placed in a furnace," for the purpose of distilling the alloy of zinc, lead, and the precious metals. A brief comparison of the Parkes and the Balbach processes is interesting. The Parkes process as practiced in England consisted in stirring into silver-bearing lead, melted in a kettle, from 1 to 2 per cent. of zinc, cooling, skimming the alloy of lead, zinc, and silver that rose to the surface, liquating it in an iron retort, distilling the residual rich alloy in fire-clay retorts, thus regaining the zinc, and refining the desilvered lead at a low heat in a shallow cast-iron pan that formed the hearth of a reverbera-tory furnace. If the lead was too impure, it was first softened

Jan 1, 1913

By E. C. Mahan

THE text of my talk was suggested by the invita-tion of your secretary, who said that the excess productive capacity of the bituminous industry was a matter of common concern to engineers and coal operators. Cognizant of the depressed condition of the industry, he tactfully added that in common council we might find wisdom. Certainly it would seem that the application of the best engineering knowledge available would be helpful in solving mining problems. There is no doubt that clear thinking, characteristic of the engineering type of mind, is essential to untangle the shapeless pattern which increased complication, so often mistaken for progress, has developed. There is much thinking today which neither looks forward to a logical combination of ideas nor backward to simple fundamentals. The result of that sort of thinking is hopeless confusion. Lately we have heard much about excess capacity and overproduction, along with their attendant evils. Respecting the bituminous coal industry, these terms have been frequently misused. How many of us have seen them applied to the coal industry but how few of us have understood them. I am reminded of a state-ment which William Green, president of the American Federation of Labor and a former miner from the Ohio field, gave to the Associated Press last month, in which he was quoted as saying: "The coal men must realize that conditions have altered since the World War. To-day they are producing a billion tons a year, with a market for only half that tonnage." I cite this instance as a glaring example of the flood of. loose statements about the bituminous industry with which the public is being deluged. If the general public, or some of the newspapers, had any passion for the facts, this sort of misleading statement would not get very far. Unfor-tunately, in these days, opinions are more sought after than facts, and statements by such a person as Mr. Green and are promptly accepted by a credulous public.

Jan 4, 1928

By R. E. McNulty, R. D. Heidenreich, C. H. Gerould

TIIE electron microscope techniques and their application to magnesium alloys that are to be discussed in this paper are the result of research at The Dow Chemical Co. over the past three years. The view- point underlying the work is not wholly metallurgical, but has evolved through a variety of problems related to the physics and chemistry of surfaces. It can be said that the interest and stimulus were closely associated with a desire to employ effectively the electron microscope in research concerning the properties of solids as related to their physical structure. Only a portion of this work will be described here, and, consequently, many points of interest and debate are of necessity either only briefly recognized or are completely omitted. As has been pointed out by Desch,1 a great deal of the knowledge of the structure of metals has been obtained through microscopic studies of the surfaces of metallic specimens prepared in a particular manner. This information, when added to that obtained by means of thermal, electrical, X-ray, dilatometric and other methods, has been of great value both from a theoretical and a practical view- point. With the introduction of new instruments such as the electron diffraction camera and the electron microscope, it would be expected that still more information could be obtained. These two instruments have in many instances been very effective when directed toward the investigation of metallic surfaces, provided the proper methods of surface preparation were employed. Experience shows that the problems of surface preparation greatly limit the general application of these instruments to metallographic studies. It was found necessary to discard the standard metallographic procedures in applying the electron microscope to magnesium alloys and to work out new methods, which were required to satisfy certain conditions. These methods are unique to magnesium only in the specific chemical reactions occurring during etching. The presentation of the methods and results will be ordered as follows: I. Electron Microscopy of Surfaces. 2. Surface Preparation of Magnesium Alloys. 3. Discussion of Microstructures. a. Pure Magnesium and Single-crystal Studies. b. Types of Precipitation. c. Some Common Structures. d. Special Micrographs and Techniques. e. Structure of Mg-A1 Solid Solutions. 4. Correlation of "Fine Structure" with Corrosion Behavior of Magnesium Alloys.

Jan 1, 1946

HAVING previously described the metals to you, before I proceed any farther I do not wish to fail to tell you, as I promised to do in the first chapter on metals, what I have learned through experience concerning the semiminerals, although this may seem to you outside our proposed subject. Since these are not produced by Nature as all rock or all metal they are called semiminerals by speculative physicians. Many kinds of these are found; those that resemble rocks are earthy, very difficult to liquefy, and much more adapted for adorning paintings than for anything else. Those that liquefy with fire, like sulphur, antimony, marcasite, [22] calamine, zaffre, manganese, and others, resemble the metals almost like brothers. Some others are more watery so that they dissolve in water, although they are fairly dense, and are obtained and reduced to their, perfection by means of water. These are the salts, vitriol, rock alum, and saltpeter. To these, as a watery thing, belongs also quicksilver, as it is commonly called because of its motion. Although it appears. not only liquid, but very liquid, this is not at all similar in its effects to any of the above. Indeed, it retains its same being until its very form is consumed. Since the reasons for its effects are almost impossible to investigate, I do not intend to speak of them here or to enter now this maze of speculation, because I wish to make definitely clear to you what this quicksilver really is. Therefore, leaving aside opinions and disputes, I shall take only those of the said semiminerals that I know are useful. First we shall see the method by which the semiminerals can be found and then how they are to be extracted from their matrices. These, perhaps, have no less need of effort and industry than the metals since they are substances completely hidden in the rocks or in the earth. For this reason some of these that are sought are made use of by means of fusion after they have been mined from their mother mountains, and some others need to be disposed by a certain maturative corruption, now with moisture and coldness, now with dryness and heat, as with waters, rains, frosts, or long baking in the sun, with fire, or even with a strong reheating within themselves. Most of them can finally be brought to the desired end by means of solution with water and fire.

Jan 1, 1942

By A. W. Hesse

VENTILATION of all types of coal mines is fundamentally the same, in that sufficient air must be provided to properly dilute and remove dangerous and obnoxious gases and leave the oxygen content of the air not under 19 per cent in all places where men and animals must work. Perhaps animals should not be mentioned, as the speed of mechanical loading leaves livestock behind and outmoded. Since this paper has to do with the influence of mechanical loading equipment on ventilation, the problems will be confined to the splits and the coal-producing places of the mine. The removal of coal dust from the air, or its rapid transmission to the return air courses; the possible increase in the liberation of gases by the multiplication of cuts in the coal made during one shift or multiple shifts; and the additional electrical equipment at the faces, are the factors that cause the added importance to good ventilation in the permissible equipment area of gassy bituminous coal mines. VENTILATION FOR MECHANICAL LOADING IN GASSY MINES In gassy mines, the air currents must be maintained across the faces in such a way as to prevent short cuts to the returns and leaving pockets in which accumulation of gas might occur. To do this, two or more doors are required on almost every entry containing a track to the face, so located that in no event will a trip of cars block open the doors and permit the air to by-pass some place or places on the air-approach side. This method frequently requires the use of unusual lengths of duplex cables to reach the mechanical equipment at the faces, particularly where the distances between parallel working places are 100 ft., as at the Nemacolin mine. Fig. I shows a pillar section being worked with mechanical loaders. This layout requires carrying the air in on the right and releasing it on the left, because the track clearance is on the right side and the line brattice is built on this side from the last crosscut to the face. Thus, the air travels to the face with greater velocity, and gives more assurance of sweeping out the gas that might be exuding from the crevices of the coal. All working places, in driving through solid coal, are thus treated alike. They are all potentially gassy and must be swept clear of whatever may contaminate the air. Once the air starts into the working section, it is not released until it does a good job. Of course the volume of air must be large enough not only to dilute the gases but to carry away explosive fumes and fine coal dust quickly. Mechanical loading entails cutting and drilling of the coal during the same working period as the loading when two-shift and three-shift operations are employed, and all three processes create finely pulverized coal, which in itself is hazardous if not controlled by some means. If the ventilation is inadequate and gas accumulates, and a spark from defective electrical

Jan 1, 1941

By A. W. Peake, F. O. Prior

Considering the great advance in the development and application of electricity, it is not strange that eventually a big field for its use has been found in oil-field operations. So far as is known, the first electric drive in oil-field operations was in the Russian field of Baku in 1900. The first application in this country was made by the South Penn Oil Co. near Folsom, West Va. in 1903. In 1916, electric power was first used in the Burma fields of India for drilling and pumping. Between 1916 and 1922, The Empire Gas & Fuel Co. made the first large electrical installation in the Mid-Continent fields. But although the first application was made 27 years ago, it is only within the last 10 years that oil companies have begun to look upon its use with much favor. Within the last few years, there has been a steady increase in the use of electricity in the oil fields. The first application of electricity for oil-field operations in Wyoming was in the Lander field in 1919; the second was in 1924 in Salt Creek; and the third, and last to date, was made by the Continental Oil Co. in the Big Muddy field during 1926. Lander Field The electrification of oil-field operations in Wyoming was initiated by J. W. Steele, superintendent of the Producers & Refiners Oil Corpn., in the Lander field in 1919. At that time, 32 wells were being pumped from five band-wheel powers, with oil engines as the prime movers. Eight barrels of fuel oil were used for power per day and at the price of 90 c. per bbl. the fuel bill was $36 per day. It was decided to try a 15 to 35-hp. oil-field motor on one of these powers. Electric power was generated with steam at the old Wind River refinery station. This test was so successful that in 1920 all five powers were equipped with 15 to 35-hp. oil-field motors, the power being obtained from the Sinks Canyon hydroelectric station. Four of these powers pumped wells at an average depth of 1450 ft., and the fifth pumped wells at an average of 2100 ft. In 1920, the average production per day from the 32 wells was 325 bbl. The power bill on the

Jan 1, 1928

By F. C. Pittman, D. W. Harriman, J. C. St. John

This paper mentions briefly the history of hydraulic jetting as applied to perforating and fracture initiation. It points out the advantages of hydraulic perforation and undercutting as an aid for creating a fracture at the point desired rather than depending upon the weakest point in the formation for breakdown. It describes early experimental work with jet nozzles in search of better nozzle materials. The effect of splash-back damage and its subsequent influence on jet body and tool design during this work is discussed. A series of cutting-rate curves for jets cutting steel and steel-cement-formation combinations is presented to show the effect of hydrostatic head and the point of diminishing returns with respect to cutting time. There is a series of photographs showing various types of rock formation in which perforation and undercutting tests were made. These stones were drilled and the casing cemented in place as in an actual well. The casing was perforated and circularly cut as if preparing for a fracturing job. The conclusion reached in the paper is that hydraulic jetting with sand-laden fluid can be used for perforating and undercutting casing, cement and formation rock for the intended purpose of inducing the formation to fracture at a desired point. INTRODUCTION Hydraulic jetting as a means of cleaning a formation during acidizing has been used for many years. The acid-jet gun was used to clean formation and for drilling cement from casing with acid. This tool was dropped to a seating ring installed on the tubing and could be retrieved by reverse circulation or wire line. In this process, the fluids were directed against the formation to clean and penetrate beyond the mud-damaged area. After the development of the hydraulic fracturing process, interest in jetting the formation with abrasive-laden fluid was renewed. The cutting action of abrasive fluid on pumping equipment, which is a well known problem, has been utilized to perforate and undercut casing, tubing and formation. In this process, surface areas are provided in the formation on which the frac- turing pressures may work to produce a fracture at the location desired. EQUIPMENT The tools used consist of bodies containing two, three or four jets in a single horizontal plane equally spaced around the circumference. The body is threaded to the end of a string of tubing and run into the well. In addition, an expendable tool is available that may be left in the hole after perforating and produced through until necessary to remove the tubing. The bottom of each tool is equipped with a ball-type back-pressure valve. The ball can be reversed to the surface and recovered. This allows reverse circulation so that loose sand which accumulated below the tool while jetting may be removed before the fracturing job. The present jetting tools are of such length that, when screwed together, the jets fall on 12-in. spacing. ANALYSIS OF THE PROBLEM Early work with nozzles indicated that hardened steel was not a suitable material for jets and that more durable material would be required. Ceramics were tried and found to be superior to steel but still too shortlived for most applications. Tungsten carbide, which was tried and found to be the best material available, is now being used for jet nozzles. Analysis of the problems presented by this process indicated that the following information was needed. 1. The effect of submergence on a jet stream and the effect of submergence on the cutting rate of a jet stream. 2. The cutting rate and depth of a jet stream in steel. 3. The cutting rate in various formations and point of diminishing returns. 4. Size of hole or slot cut in a pipe by a given jet. 5. Fluids and sands used. 6. The flow of various weight fluids through the jet nozzle and the discharge coefficients. 7. The type cut formed in the formation by the jet stream. 8. The stretch and contraction of tubing due to temperature and pressure. The cutting effect of a jet stream on a target in the atmosphere is rapid and spectacular as most of the

By L. G. Jones

An approximate method of calculation is developed in this paper which allows duplication of radial unsteady-state gas flow computer results where Darcy's law applies, such as those reported by Aronofsky and Jenkins and Bruce, Peaceman, Rachford, and Rice. Moreover, the new calculation method can be used to obtain results for radial unsteady-state gas flow obeying the quadratic flow law proposed by Duwez and Green. Means are discussed for predicting well behavior at single or superimposed flow rates in finite or infinite reservoirs, determining reservoir rock properties from well-test data, reproducing and interpreting back-pressure test data, and determining the radial extent and reserves of gas reservoirs from well-test data. Example calculations are presented for gas flow following both Darcy's law and the quadratic flow law. INTRODUCTION Since the publishing of U. S. Bureau of Mines Monograph 7,1 most gas-well testing methods have been based on the equation q = y (pl2 - pw2)a, where q = production rate, pl and pw, are formation pressure and sandface pressure, respectively, and y and a are constants to be obtained from test data. These methods, used for predicting both deliverability and "open-flow" capacity of gas wells, have been useful and accurate in many cases but unsatisfactory in others. Even at best, however, they do not supply information about the formation or lead to an understanding of nonsteady-state gas flow in porous media. Many theoretically based studies2-4 of gas flow obeying Darcy's law have been made.' Since the partial differential equations which result from combining Darcy's flow law with the continuity equation are nonlinear, most of the published research consists of either numerical solutions or analytical solutions for linear approximating equations. Such solutions have been of limited value in field work due to their unhandy form and their failure to correlate most field data. There is evidence5,6 which indicates that Darcy's law is inadequate to describe gas flow at some flow rates of practical interest. A quadratic flow law: which reduces to Darcy's law at low rates, is more successful in accounting for experimentally observed behavior. This flow law has been applied successfully to a few hypothetical reservoir cases in work which has recently been published.10 However, these numerical solutions of the equations involved have been successful only on a special analog computer. Routine applications to field cases would be awkward and have not been attempted. The present paper describes an approximate method for computing nonsteady-state gas flow solutions which has been completely successful in predicting the results for both Darcy flow and quadratic flow obtained by elaborate numerical methods. The new calculation method allows determination of the observable variables in gas-well testing at constant rates. It is similar to the scheme of using a succession of steady states suggested by Muskat7 in that it makes use of steady-state and material-balance equations. It also is similar to the work of Aronofsky and Jenkins2 in that the new method includes Aronofsky and Jenkins' stabilized flow equation as a special case. It improves upon both of these calculation schemes in that it accurately describes all portions of reservoir history and suggests means of determining reservoir rock properties from well-test data. This paper deals only with production from a reservoir, in which case the rate is defined as being negative. The reservoir studied here is a homogeneous, disk-shaped porous body of uniform thickness, with all boundaries sealed except the inner radial boundary of the well.

By H. A. Schlesinger

Various studies have estimated that for the next few decades, about half of all new power plants will be nuclear. The other half will be fueled with coal. Pending legislation on air pollution control would require all new coal-fueled power plants to install stack gas scrubbers or other technology to reduce sulfur oxide (SO,) emissions. These regulations would require flue gas desulfurization (FGD) or other technology for SO, reduction even on lower sulfur western coals. Among the options for FGD are single or dual alkali throw away processes using lime or limestone as the major reagent. These processes are currently more economically attractive than recovery processes, such as magnesium oxide and Wellman- Lord, that produce a salable product such as sulfur or sulfuric acid. One of the major problem areas with the throw away processes is disposal of the thrown away solid wastes, primarily calcium sulfite (CaSO3) and calcium sulfate (CaS04). Coal ash also must be disposed of, even if SOx reduction is not required. This paper addresses the alternatives for handling and disposal of throw away lime, limestone, and dual alkali process solid wastes. Advantages, disadvantages, and the economics of various methods are discussed. Both large central station power plants (500-1000 MW capacity) and smaller industrial power plants (up to 100 MW capacity) are considered. High sulfur eastern coals (53% S) and lower sulfur (3 1% S) western coals are considered.

Jan 1, 1981

By W. Mostowitsch, H. O. Hofman

In a previous paper,' The Behavior of Calcium Sulphate at Elevated Temperatures with Some Fluxes, we published the results of our investigation into the behavior of calcium sulphate in air; that is, under oxidizing conditions. The results as a whole hold good for a neutral atmosphere, or one which has no chemical effect upon calcium sulphate. The present paper deals with the behavior of calcium sulphate under reducing conditions, the reducing-agents employed being carbon monoxide and carbon, and the changes the calcium sulphide formed undergoes when it is subjected to an oxidizing-roast. Technical literature deals very sparingly with the subject. The information furnished by the recent leading chemical manuals is general. Thus Dammer,2 Missan,3 and Abegg4 quote Berthier as having reduced, in 1823, calcium sulphate with carbon, and Stammer as having done the same in 1851

Jan 1, 1911

By C. Chu

An investigation has been made of the radial heat-wave process using a mathematical model in two-dimensional cylindrical coordinates. This model considers combustion, convection and conduction inside the reservoir, but only conduction in the bounding formations. From a study of the general features of the process, an important phenomenon has been revealed, namely, the feedback of heat into the reservoir on the trailing edge of the heat wave. The effects of various process variables on the performance characteristics of the process have also been investigated. It was found that up to the time when the combustion front reaches a given point, the per cent heat loss, provided it is not higher than 40 per cent, is approximately directly proportional to the square root of thermal conductivity arid fuel content, but inversely proportional to the square root of gas-injection rate and oxygen concentration. The effecr of reservoir thickness is more pronounced, since halving the thickness doubles the per cent heat loss. The most decisive factor in determining the center-plane peak temperature is the fuel content of the reservoir. Within the temperature range investigated, doubling the fuel content doubles the peak temperature in the early stage, but the rate of decline of the peak temperature is high. Reservoir thickness is also a very influential factor. The peak temperature is lowered when the thickness is reduced; however, the effect of thickness becomes less pronounced when the thickness is high. Reduction of oxygen concentration increases the peak temperature in the early stage but lowers it afterwards because of the higher rate of decline of the peak temperature. Increase in gas injection rate or decredse in thermal conductivity geives a higher peak temperature which stays high for a longer period. The propagation range of the heat wave is chiefly governed by the fuel content of the reservoir. An increase of 0.2 1b/cu ft in the fuel content increases the propagation range by 100 per cent. The propagation range is more than doubled by doubling the gas injection rate, or reservoir thickness, or by reducing the thermal conductivity by 50 per cent. Comparatively, oxygen concentration has less effect on the propagation range. INTRODUCTION Several investigators have conducted theoretical studies of a radial heat wave. Vogel and Krueger1 studied a system with a moving cylindrical heat source of constant temper- ature, considering conduction in the radial direction only. Ramey2 included conduction in the vertical direction in his studies. Bailey and Larkin2 attacked a more general problem where initial well heating, vertical heat losses and arbitrary frontal velocities were included. In all these studies, however, conduction was considered to be the only means of heat transfer. Bailey and Larkin in a later paper included the effects of convection in a study involving both linear and radial geometries. Vertical heat losses were neglected in the radial case. Katz5 studied a similar problem in a one-dimensional radial model, using a heat-loss coefficient to account for vertical heat losses. Selig and Couch6 mployed a cylindrical model and investigated two limiting cases. In one case they considered no heat loss from the reservoir whereas in the other they assumed a constant temperature at the interface between the reservoir and its bounding formations. Thomas' studied a more general case but assumed a permeable bounding formation so that the convection effect is not confined to the reservoir. In the present work a more realistic and more generalized model is used. It involves a two-dimensional cylindrical system with combustion, convection and conduction inside the reservoir, but only conduction in the bounding formations. The purpose is to establish the temperature distribution both inside and outside the reservoir, to study the general features of the radial heat wave process, and to investigate the effects of various process variables on the performance characteristics of the process. THEORY We fist consider a circular porous reservoir of thickness H extending vertically from y = — H/2 to y = + H/2. The reservoir extends from a well bore radius r, to an external radius re. A stream of oxygen-containing gas is introduced into the reservoir through the wellbore. The oxygen-containing gas reacts with the fuel contained in the reservoir and forms a combustion front wherever the prevailing temperature can support the combustion. It is here assumed that this combustion front constitutes a cylindrical surface source of heat having an infinitesimal thickness in the radial direction and extending vertically throughout the whole thickness H. This is designated as Region I. We next consider a Region II corresponding to the upper and lower formations bounding the reservoir, extending from y = — - to y = — H/2 and from y = + H/2 to y = + m. Since r, is very small, we may assume that the two bounding formations have the same dimensions, symmetric with respect to the center plane of the reservoir. In this way, we may take the upper half of the system alone into consideration. In contrast with

IT may perhaps seem to you that I have deviated from sequence by having entered into the narration of this arrangement of the bellows, but, although they are not furnaces or vessels for containing the melts, they are essential agents for bringing to port the bark of your labors. Returning to our regular pathway, and supposing that, besides making the moulds, you have melted and cast not only statues and bells but also guns, it is true that a certain procedure is required in order to finish them. For this you should have the moulds full, and they should have come out very well, for in truth reason does not allow that they turn out otherwise for one who uses precaution. [II2V] Then you have taken your casting from the pit and have freed it of clay. Since I have told you nothing beyond this, do not be dismayed if you see the castings so rough and in a form that scarcely shows what they really are, for I wish to open up part of the way into the great labor of finishing them so that it may seem to you that you have been somewhat helped by me. Therefore, when it is a gun, first see that the iron spindle that has been placed in the middle of the core is taken out. You can do this easily by striking the heel of the core, especially if the spindle had first been covered with ashes, hemp, or a little rope. Then saw off the feeding head above the mouth, using either a dun steel saw with tiny straight teeth that has been tempered with oil or some other fat, or a hay sickle whose edge is gently hit by a little hammer. Then have the clay that is attached to the curls or other bronze parts lifted away with a chisel. Then with a scouring brush and water uncover the emblems, coats of arms, borders, and cornices that you made as ornaments. Striking it with a hammer, push inwards every superfluous bit of bronze. Finally, having cleaned the bronze by washing, scraping, and cutting away every bit of clay, strike its surfaces gently with a large hammer and thus make it very smooth. Likewise finish the mouth and all its cornices as exactly and completely as possible with files and any other instrument that serves best. Then take a long, powerful tool that has some steel on the point, made like a chisel and somewhat bent, or with three points like the iron blade

Jan 1, 1942

By John Chipman, Theodore B. Winkler

In order to understand more fully the complexities of the reactions occurring between the liquid steel and the slag in the basic open-hearth steelmaking furnace, investigations in this country and. abroad have turned to laboratory equilibrium studies. This paper is one of a series of reports on investigations being conducted at the Massachusetts Institute of Technology. The experimental work was completed early in 1942. The slag systems found in the basic open hearth are very complex, being made up of at least eight major components and as many others whose effect might be classified as minor. The first two papers of the series, by Fetters and Chipman,l,2 as well as the paper by Taylor and Chip-man,3 dealt with the simplest possible slag system that would resemble those found in the basic ope), hearth—the slag system consisting of CaO-MgO2-SiOz-FeO. (Taylor's rotating induction furnace eliminated the necessity of contamination of the slag by MgO.) Having arrived at some reasonable conclusions regarding the physical chemis- try of the reactions between molten iron and the simple slags at equilibrium, the next step was to investigate more complex slag systems. The major purpose of the present investigation was to determine what factors control the distribution of phosphorus between molten iron and the more complex basic slags at equilibrium, and to what extent these factors are influential. The slags used contained CaO, MgO, SiO2, FeO, Fe2O3, P2O6, MnO, Al2O3 and CaF2, but not all of the slag samples contained all of these components at one time. Review of Literature Although a number of interesting papers have been published on the subject of dephosphorization of an iron bath, there are as yet no results from laboratory studies that give thoroughly reliable information on the dephosphorization reaction. Even for the supposedly simple Fe-O-P system involving iron-phosphorus melts and iron oxide-iron phosphate slags, the experimental results are contradictory and no formulas have been established that adequately fit the equilibrium conditions. The Fe-O-P system has been studied by Schackmann and Krings,4 von Samson-Himmelstjerna,6 Oelsen and Maetz,6 Bischof and Maurer,7 Diepschlag and Schürmann,8 and Herty,9 and the results of their investigations appear in Table I. A number of different equilibrium constants and distribution . Ratios

Jan 1, 1947

By Theodore B. Winkler, John Chipman

In order to understand more fully the complexities of the reactions occurring between the liquid steel and the slag in the basic open-hearth steelmaking furnace, investigations in this country and. abroad have turned to laboratory equilibrium studies. This paper is one of a series of reports on investigations being conducted at the Massachusetts Institute of Technology. The experimental work was completed early in 1942. The slag systems found in the basic open hearth are very complex, being made up of at least eight major components and as many others whose effect might be classified as minor. The first two papers of the series, by Fetters and Chipman,l,2 as well as the paper by Taylor and Chip-man,3 dealt with the simplest possible slag system that would resemble those found in the basic ope), hearth—the slag system consisting of CaO-MgO2-SiOz-FeO. (Taylor's rotating induction furnace eliminated the necessity of contamination of the slag by MgO.) Having arrived at some reasonable conclusions regarding the physical chemis- try of the reactions between molten iron and the simple slags at equilibrium, the next step was to investigate more complex slag systems. The major purpose of the present investigation was to determine what factors control the distribution of phosphorus between molten iron and the more complex basic slags at equilibrium, and to what extent these factors are influential. The slags used contained CaO, MgO, SiO2, FeO, Fe2O3, P2O6, MnO, Al2O3 and CaF2, but not all of the slag samples contained all of these components at one time. Review of Literature Although a number of interesting papers have been published on the subject of dephosphorization of an iron bath, there are as yet no results from laboratory studies that give thoroughly reliable information on the dephosphorization reaction. Even for the supposedly simple Fe-O-P system involving iron-phosphorus melts and iron oxide-iron phosphate slags, the experimental results are contradictory and no formulas have been established that adequately fit the equilibrium conditions. The Fe-O-P system has been studied by Schackmann and Krings,4 von Samson-Himmelstjerna,6 Oelsen and Maetz,6 Bischof and Maurer,7 Diepschlag and Schürmann,8 and Herty,9 and the results of their investigations appear in Table I. A number of different equilibrium constants and distribution . Ratios

Jan 1, 1947

By A. W. Schlechten, A. H. Larson

Equilibrium H2S/H2 ratios were determined as functions of temperature (500o to 900°C) and composition in a hydrogen-circulation apparatus. Within the composition range studied there exists a two-phase region of "Zr3S4" and "ZrS2". The upper composition limit of this two-phase region is hounded by a disulfide phase and is practically constant over the temperature range investigated. The lower composition limit of this two-phase region is bounded a "Zr3S4 " phase and varies appreciably with tem- perature. The upper composition limit of the homogeneous region of the disulfide phase is not definitely determined, but it appears to he bounded by the stoichiometric composition of ZrS2. The lower composition limit of the homogeneous region of the Zr3S4 phase could not he determined due to the extremely low values of the equilibrium H2S/H2 ratios. Various thermodynamic quantities are evaluated from the data. PUBLISHED free-energy data for the Zr-S system are practically nonexistent. Strotzer, Biltz, and Meisel1 measured the sulfur pressures for the reaction 2ZrS2(s) + S2(g) = ZrS3(s) in the temperature range 783" to 874°C. The average heat of reaction calculated from the temperature dependence of the sulfur pressure is -47 keal. It should be noted, however, that according to these investigators, the two-phase region as determined by sulfur pressure constancy under isothermal conditions extended from approximately ZrS2, 3 to ZrS2.7. From consideration of X-ray data they concluded that the homogeneous regions of the disulfide and trisulfide phases are ZrS1.8-2.0 and ZrS2.8-3.2, respectively. Hahn and coworkers2 have made a structure study of the zirconium sulfide phases. They summarized the zirconium sulfide phases as follows: the compounds ZrS3 and ZrS2 with narrow homogeneous regions, a "Zr3S4" phase with a homogeneous region roughly within the limits of ZrSl.5 and ZrSo.9, the compounds ZrS and Zr4S3, and a "Zr3S2" phase with a homogeneous region within the limits ZrSo.8 and ZrSo.5. It is noted that the compounds ZrS and Zr4S3 are only formed in the gaseous state through sublimation of a phase which has the approximate composition of the compound. This paper describes the determination of the stability of the zirconium sulfide phases by a hydrogen-reduction method in which hydrogen is circulated over the heated sulfide until equilibrium is attained. The resulting H2S-H2 mixture is then analyzed. Partial molar free energies, enthalpies,

Jan 1, 1964

By John E. Conley

THE production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.1 The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require additional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnston,2 Smyth and Adams,3 Ralston et al.,4 Furnas,5 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894º to 898º C. The dissociation of dolomite and magnesite, although studied by several investigator,4, 6, 8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (1) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1939