Search Documents

By Joseph Gurland

EVERAL carbide-cobalt compositions were pre-^-5 pared for the purpose of determining the transverse rupture strength of various carbide-binder systems. The binder content was held at 10 and 37 volume pct Co, so as to be representative of low and high bjnder compositions. The carbides used, WC, Tic, TaC, CbC, VC and ZrC, were selected on the basis of availability, knowledge of their properties, and small solid solubilities in the binder metal at room temperature. The methods of preparation and carbon analysis of the carbides are summarized in Table I. The carbides with cobalt added were ball milled, pressed, and sintered. vacuum sintering was used throughout, except for the WC-Cs alloys, which were sintered in hydrogen. The sintering temperatures ranged from 2500" to 2750°F for the low binder alloys and from 2300" to 2550°F for the high binder alloys. Compositions and properties of the sintered com- pacts are presented in Table 11. For the transverse rupture strength, the average and range of the five best samples of each alloy are listed. Discrepancies between the actual and theoretical densities are attributed to carbon deficiencies in some samples. The theoretical densities were calculated by assuming mixtures of carbides of stoichiometric compositions and cobalt. Representative microstructures are shown in Figs. 1 to 6. The porosity was A-2 or better' in all alloys except those with ZrC. A grain size of about 3 p was

Jan 1, 1958

By Samuel M. Cassidy, John A. Garcia

IN some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. As far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haul- age and air. On completion of the panel the two entries are sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1937

By J. C. Bartlett

The following discussion was suggested by an experiment of Mr. Krom, the Manufacturer of air-jigs, to illustrate the superiority of air over water as a medium of concentration. The paper is written in the interest of no system of concentration, but simply to test the experiment, and, perchance, to add something to the general fund of information on the subject. To speak of testing an experiment by a theoretical discussion, may seem a misuse of terms, but the theories concerning falling bodies and the resistance of fluids are pretty well crystallized into laws, which may properly be used to show where experiments which seem to refute them were improperly performed, and that instead of refuting they only corroborate. It is well known that a sphere of galena & inch in diameter, and a sphere of quartz 1/2 inch in diameter, are equal falling in water ; that is, these two spheres, being placed together in a column of water at rest or in motion, will practically remain together, filling or rising together, or remaining in suspension. Mr. Krom, to show that these

Jan 1, 1879

By David R. Mitchell

IF you are the owner of a mine, or a mine executive, or just an ordinary miner, and have a son about to go to college, do you urge him to take up mining engineering or do you try to dissuade him from such a course? If you live in the East, or the Middle West and your interest has been in coal rather than metal mining, the chances are that your young hopeful will be urged to do almost anything else rather than follow in father's footsteps.

Jan 1, 1939

By Nicholas J. Grant, H. C. Chang

TRANSCRYSTALLINE fracture surfaces of the cleavage type have been examined by microscopy and X-rays for several metals.' These investigations revealed that the fractured surfaces were not flat and invariably had cleavage and other deformation markings on them. On the other hand, the study of inter crystalline fracture surfaces has been limited. Perryman, in a recently published paper on the inter crystalline fracture of ß-brasses,' found that a thin layer of heavily deformed metal was invariably associated with these surfaces. Furthermore, the thickness of this layer was found to depend on the orientation of the grain boundary surface with respect to the applied stress. The mechanisms of grain boundary sliding and intercrystalline fracture have been presented in two previous papers,which described certain aspects of the deformation of a 20 pct Zn-A1 alloy. It is the purpose of this paper to present some observations on the structure of intercrystalline fracture surfaces and to correlate the structure of such surfaces with the mechanism of intercrystalline fracture. Experimental Techniques—The high purity 20 pct Zn-Al alloy was generously supplied by the Research Laboratories of the Aluminum Co. of America. Two sizes of specimen were used; the first had two parallel flat surfaces of dimensions 1x0.17x0.09 in. and the second was round with a 0.25 in. diam. A grain diameter of 1 to 3 mm was obtained by annealing the specimens at 1000°F for 24 hr. The specimens were then air cooled. The specimens were subjected to creep at 500°F and 2300 psi. The rupture times ranged from % to 3 hr, with one room temperature tensile test. It has been mentioned previous1y" that the intercrystalline fracture surfaces of this alloy, when tested under the conditions given above, are sharply defined. In the optical examination of the fracture surfaces, whenever possible, magnifications of at least X250 were used. The locations of the regions examined, both optically and by X-rays, were selected to give several fracture surface orientations with respect to the stress axis and to the specimen surfaces. This was possible for the X-ray studies since the grain diameters were large compared to the X-ray beam. A film to specimen distance of 3 cm, a 1 mm pinhole and Cr radiation were used for the Laue back reflection pictures.

Jan 1, 1957

Discussion of the paper of W. H. Gunniss, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 81, September, 1913, pp. 2309 to 2310. PROF. J. W. RICHARDS, South Bethlehem, Pa. :-In regard to the physical nature of quartz for making silica brick, is the coarse-grained preferable ? E. P. MATHEWSON, Anaconda, Mont. :-A dense quartz is preferable. The quartzite is the actual material used by the Anaconda Company. The sandstone referred to, the foreign quartz, was a very pure sandstone and bad hardly any impurities in it, and the brick made from that particular material, while apparently beautiful while coming out of the kiln, and true, immediately on heating in the furnace buffed up half an inch and were cracked open.

Jan 11, 1913

By J. E. Powell, F. H. Spedding

WHILE rare earths are reported to be widely distributed in nature and are not really rare," in practice, there are only a few minerals which are sufficiently rich in rare earths to serve as practical sources. Perhaps the best known of these is monazite which is a phosphate mineral containing rare earths and thorium. This mineral occurs as a dense brown sand in gravel beds and is particularly rich in the light rare earths of the cerium subgroup. This mineral is processed commercially for its thorium, cerium, and lanthanum content, and, consequently, furnishes rich concentrates from which neodymium, praseodymium, samarium, europium, and gadolinium may be obtained. Unfortunately, monazite is rather lean in rare earths heavier than gadolinium. A second mineral which is rich in the light rare earths is bastnasite, a fluoro-carbonate. Extensive deposits of this ore have been discovered in the western United States and have received considerable newspaper publicity in recent years. While bastnasite is very rich with respect to cerium, lanthanum, and neodymium, it contains even less heavy rare earths than does monazite. One of the better sources of heavy rare earths of the yttrium subgroup is gadolinite, a black silicate rock from which the rare-earth content can be extracted readily by acid leaching. It is obtained chiefly from Norway at the present time, although there are known deposits in the United States. Other sources of heavy rare earths include fergu-sonite, euxenite, and samarskite which are refractory tantalo-columbate ores. These minerals require caustic fusion or reduction to carbides with carbon before the rare-earth content can be extracted. All of the minerals which are rich in the heavy rare earths contain yttrium as a major constituent. After the rare earths have been extracted as a group from an ore by chemical means, it is generally convenient to precipitate them from acid media with oxalic acid in order to eliminate certain non-rare-earth impurities such as iron, beryllium, etc., which are usually present. The oxalate can then be readily ignited to R2O3. The oxide can be dissolved in acid and is the starting point for subsequent separation into the pure components. Perhaps the principal reason why the rare earths have not been studied as extensively as other elements of the periodic table, whose natural abundances are comparable, is that they are extremely difficult to separate from each other by the usual chemical means. Prior to 1945, the separation of one trivalent rare earth from another was a laborious process. All separations were based on repeated fractionation processes, i.e., fractional precipitation, fractional decomposition, fractional crystallization, etc. These processes were repeated from a few hundred to many thousands of times in order to obtain individual rare-earth salts of reasonable purity. Of course, mention should be made that, in the few cases where a rare earth could be oxidized or reduced to a valence state other than three, more conventional chemical means could be utilized to separate the oxidized or reduced ion from the other normally trivalent rare earths. The ionic states which deserve special mention are CeIV, SmII, Eu11, and Yb11. When it is possible to remove an element of the series efficiently, due to an optional valence state, its immediate neighbors also become easier to isolate. For example, binary mixtures of lanthanum and cerium, and praseodymium and cerium can be obtained by a relatively small number of fractional operations. The tetravalent state of cerium then allows the complete resolution of the binary mixtures by ordinary chemical means. Although the tetravalent state of cerium has been known for a long time, the divalent states of samarium, europium, and ytterbium were not used extensively in separations prior to 1930 because they are relatively unstable in aqueous media.'-" No attempt will be made to give a comprehensive review of the extensive literature dealing with the separation of rare earths. Rather, this paper will be confined to a review of those methods which have been developed at Iowa State College during recent years, and which have proved extraordinarily successful for the isolation of highly pure rare earths in quantity. It was obvious that, if pure rare earths were to become generally available, methods would have to be developed wherein the thousands of fractional operations made necessary by the similarity of rare-earth properties could be performed automatically. The development of chromatographic techniques and ion-exchange resins appeared to offer a mechanism by which this objective could be accomplished. A number of early attempts were made to separate rare earths by these means; for example, Russell and Pearce12 passed a mixture of rare earths through a cation-exchange column and reported

Jan 1, 1955

By Thomas Egleston

All industrial establishments whose operations depend upon chemical reactions use gases. In the simplest case the oxygen of the atmosphere, heated or not, as the case may be, is used, and in other cases, gases which are produced by a special apparatus of more or less complex composition. The manufacturer depends, for the success of his operations, entirely upon having these gases arrive at the right time, in the proper proportions, at the required temperature. It often requires but a slight variation in their composition to make a given process a success or a failure. In most cases the gas used is formed from fuel, and according as variations in its composition are produced by alterations in the manner of charging the grate, not only different, but often directly opposite, results are obtained. The great industrial question of the present time, and one upon which the prosperity of the world depends, is how to get the greatest amount of useful effect from fuel, whether the caloric is used directly or is transformed into horse-power. In almost all industrial pursuits this translates itself into the question of how to construct a fireplace and its adjuncts in such a way that the heat of the flame and of the products of combustion shall be made to produce a maximum effect. Unfortunately, until very recently, except by comparison, there was no means of ascertaining whether the loss of useful effect was 80, 40, or 20 per cent. of the total amount of fuel employed. It seems now strange that there should have been furnaces so constructed as to produce 20 per cent. of carbonic acid in the fireplace, but this has been proved by analysis to have been true. It does seem incredible that, notwithstanding the immense number and variety of furnaces used for different processes, and the great difference in kind, quality, and quantity of fuels consumed, there should formerly have been used for them all, the same stereotyped fireplace, varied only in its dimensions of height, length, and breadth. It is true that, with a good fireman, excellent effects may be, and have been, produced, but the manufacture is here, as in many other cases, dependent on the intelligence of the workman, a very uncertain reliance for capital to rest upon. The workman, unless he receives a prime for fuel saved, or is fined for excessive use of it, may be said

By ARTHUR THACHER

PRIMITIVE man supplied his wants as they arose; as he became more civilized he anticipated them by producing more regularly and storing the products for future use. This tended to cheapen' production and prevent ' violent fluctuations and therefore tended to increase consumption. In order to anticipate our wants, we must know what these wants will be, and this can be .determined only by statistics. 'While we have made great progress in gathering statistics, they are still far from what they should be; especially metal statistics. We determine fairly, well the amount produced, but this does not answer all inquiries because of the erratic conditions of mining, it is necessary to carry larger stocks of metals than of most other articles; moreover, as metals are more or less durable, it is difficult to determine the actual consumption. We often count under consumption what is being produced and sold, while the actual consumption is what is being worn out.

Jan 1, 1921

F. WEIMER,* Washington, D. C. (written discussiont).-For electrical measuring instruments, especially those types that involve the Wheat-stone bridge or potentiometer principle and standards of electrical resist-ance, there has been, for a considerable time, a need for better resistance materials. For a satisfactory resistance material, much depends on the purposes for which it is to be used. For potentiometers and Wheatstone bridges, such as are in more or less general use, and the more common forms of resistance standards, a good quality of manganin answers fairly well. However, it should not be presumed that manganin is considered ideal for the purpose, for in measuring instruments and resistance stand-ards, there is still much to be desired. An experience of more than 10 years in the study of the resistance standards and resistance apparatus shows that manganin resistances change with time in a way that is very annoying and the maintenance of the unit of resistance to the desired accuracy requires an excessive amount of work or may be said to be prac-tically impossible. The changes in resistance are generally most rapid and erratic in resistances of very low and very high values. In resist-ances of low value, the resistance material is often in the form of thin sheets so that the surface is large and usually more or less unprotected from the atmosphere, or the oil in. the case of oil-immersed standards. In resistances of high value, the resistance material is in the form of fine wire and, therefore, the surface is large compared with the cross-section. In resistances of medium value, the surface is less, compared with the cross-section, or better protected, usually by a silk wrapping impregnated with shellac. This suggests that one of the difficulties with manganin is slow surface action or oxidation, even when an effort has been made to protect the surface from such action However, the changes observed cannot all be accounted for on this basis. There are, presumably, also some internal changes in the resistance material even when it has been annealed. Further; the changes in manganin resistances seem to be more or less independent of its electrical properties. In other respects, too, manganin is not ideal.

Jan 11, 1919

By R. L. Schmidt, J. D. Verhoeven

The diffusion coefficients and electrotralzsport mobilities of aluminum, gallium, and arsenic have been determined in molten germanium with the capillary reservoir technique. The diffusion coefficients are slightly higher than those determined by the solidification technique of Brirton et a1.1 It was found that aluminium and gallium migrate to the cathode in molten germanium) whereas arsenic migrates to the anode under an electric field. A possible technique for producing p-n junctions by means of electric field freezing is discussed in view of the experimental data. In the past decade or so the literature has abounded with articles concerning the solid-state properties of the semiconducting elements germanium and silicon. It is surprising by comparison how little has been published concerning the liquid-state properties of these materials. In the production of doped germanium or silicon the diffusion coefficient of the dopant in liquid germanium or silicon is an important quantity. Yet, to the best of our knowledge, no one has ever made a direct measurement of the diffusion coefficient of solutes in either molten germanium or silicon. A number of authors'-4 have determined some diffusion coefficients by the indirect technique developed by Burton et al.1 This technique appears to give numbers of the correct order of magnitude but it does depend upon a number of assumptions in the analysis and also requires prior knowledge of the viscosity of the melt. In the present work a more direct measure of the diffusion coefficients of arsenic, gallium: and aluminum in molten germanium has been made. It has been shown independently by two groups of authors5, 6 that, when an electric current is passed through the interface of a solidifying metal containing an impurity, the resulting electrotransport in the liquid boundary layer at the interface offers a mechanism for control over the redistribution of the impurity accompanying the solidification. These authors show that the degree of control is proportional to the mobility, U of the impurity atoms in the liquid boundary layer, where the mobility is defined as the drift velocity relative to the solvent per unit electric field. In principle the results apply to the solidification of a doped semiconductor and offer an interesting technique for control of the doping of a semiconductor. In the present work the mobilities of aluminum, gallium, and arsenic were determined in molten germanium in order to evaluate the potential usefulness of electro-transport as a technique for solute control when applied to the solidification of doped germanium. EXPERIMENTAL PROCEDURE Both the diffusion coefficients and the mobilities were measured using high-purity alumina capillaries and a resistivity technique for analysis. A schematic diagram of the electrotransport apparatus is shown in Fig. 1 and the details of the cell design are shown in Fig. 2. For the mobility experiments electrical contact with the bottom of the capillary was made with graphite, as shown in Fig. 2. In order to prevent electrical contact with the melt the graphite was coated with a thin layer of alumina using a plasma spray torch. The cell assembly, a graphite electrode, and another assembly containing two blank capillaries were fastened to the lavite disk shown in Fig. 1. To make a run the system was evacuated and the doped germanium was outgassed at the operating temperature of 1030°C. The cell and blank capillaries were then submerged beneath the melt and a slightly positive pressure of helium was introduced to fill them. After passing current through the cell for a given time the cell and blank capillaries were raised from the melt and the furnace was shut off. The temperature of the cells dropped below the freezing point of germanium within 1 to 2 min after the furnace was shut off.

Jan 1, 1968

Your committee's secretary submits the following report, or summary, to the- members of the committee, in an endeavor to lay before them a general review of the information so far received and also his own knowledge .of the work as carried on at a number of plants, this being done in part to secure further information and suggestions from members and lead to a more effective means of furthering the work of the committee. It is suggested that more detailed data be compiled regarding engineering features involved, and that papers be contributed which will deal with the safeguarding of underground electrical installations. There are few operating companies which have not started a more or less systematic campaign to safeguard their employees from accidental injuries and unhealthful surroundings, but a great deal is to be gained by experience. All may welcome the advice and cooperation of those who have been actively engaged in the work and have demonstrated the results obtainable by organized effort, and it is, therefore, exceedingly gratifying to note the ready assistance and hearty cooperation rendered by the companies that may be truly termed pioneers in the movement. No solution of the safety problem is to be found in a strict standardization of methods, rules or devices, as' the various mining, milling and metallurgical practices present too' many conditions differing broadly in general principles, but some standard system embodying principles, already proven to be efficient should be created, which may be modified or elaborated to meet specific requirements of each individual. company, or to fit working conditions as they exist in the various mining camps throughout the country. An industrial plant is -primarily a business undertaking, therefore the economic side-of a safety or welfare campaign is of importance. Many small operators have been deterred from undertaking the work by their belief that it involved an expense beyond their means, and one that could not be counterbalanced by greater efficiency or saving along other lines. This idea is generally clue to a lack of knowledge of the actual costs of such work, and of the results secured by judicious selection of a method commensurate with the. size and nature of the opera-

Jan 1, 1917

By Grover J. Holt

Open-pit mining on the iron range has been in a stage of transition for several years from the standpoint of mechanization. The most radical change in open-pit mining methods was started in open-pit haulage in 1937 with the departure from the then standard system of locomotive and car transportation and the advent of the heavy duty truck as a replacement. The initial use of trucks was followed shortly by the first installation of a conveyor belt for open-pit ore haulage. The growth of the combination of trucks for gathering units delivering to a conveyor system for transportation out of the pit, has been rapid and this transition appears to have reached a peak in 1949 with locomotives and cars now being used in only a few of the largest open pits. One point which must be considered, if we assume that the maximum equipment change- over point has been reached, is that the largest pits have probably passed their peak of production. Future ore replacement must come from smaller pits wherein the truck conveyor system has done an outstanding job.

Jan 1, 1950

By William B. Hughes

The rubber-sleeve core barrel was developed to improve core recovery from unconsolidated sands, where it is most difficult to obtain cores with conventional barrels. The use of a rubber-sleeve core retainer, together with other departures from clsual design, has required a considerable amount of testing to prove its op-erability. Tests run in shallow experimental holes and in drilling wells in the U. S. and Vemzuela have, to a large extent, proved the operation of the barrel. Internal mechanism troubles, such as sandbinding of the sleeve, have been largely overcome. Cores have been recovered from completely unconsolidated sands where conventional coring has almost been abandoned because of poor recovery. In addition to retaining the core until brought to the surface, the barrel gives a "packaged-ar-cut" core, which is coilverzient for handling and transportatiorz. In the initial work, drag blade cutters, roller cutters, and tungsten carbide insert cutters were usrd for cutting unconsolidated sands. Further bit head development is presently being conducted using diamond heads in unconsolidated sands where shaler, hard sands, and limestones are encountered in adjacent formations. Thir work should render the barrel capable of cratting and recovering most types of formations, possibly including broken and frac- tured fornlations. This development is being carried on in cooperation with a diamond bit manufacturer. INTRODUCTIO N For many years the oil industry has needed greater recovery of cores from unconsolidated formations. Conventional equipment has been used to core unconsolidated sands with little success. Specifically, a core barrel was needed which would recover unconsolidated sands in a condition that would give useful reservoir information. DEVELOPMENT OF 'THE RUBBER-SLEEVE CORE BARREL Basic Requirements of Unconsolidated Sand Corino The basic need was defined as a core barrel that would obtain a continuous unconsolidated core with sand grains in place as deposited in the formation. A preliminary survey of coring equipment and search of the literature pointed out the weaknesses of conventional core barrels. Laboratory tests using unconsolidated sand in a metal tube simulated actual sand movement into the core barrel during conventional coring. In conventional barrels the core sometimes crumbles and bridges, or fails under compressive column action, becomes oversize, and wedges against the walls of the inner barrel. The core barrel requirements established by the surveys and preliminary tests are as follows. 1. The core should be held to- gether as it is cut so it cannot crumble and bridge against the walls of the coring tool, care being taken not to permit damage from fluid circulation. 2. The core should be continuously supported as it is cut so it will not have to support itself in compression. 3. The core should be packaged in the barrel to retain an undisturbed condition during the trip out of the well. The packaging should be such that the core can be removed from the barrel and shipped to the core analysis laboratory without physical disturbance or alteration of fluid content by exposure to the atmosphere. Operation of the Rubber-Sleeve Core Barrel The rubber-sleeve core barrel (Fig. 1) meets the basic requirements for the recovery of unconsolidated sands.

By Charles R. Keyes

Discussion of the paper of Charles R. Keyes, Bi-Monthly Bulletin, No. 19, January, 1908, pp. 1 to 31. BERNARD MACDONALD, Guanajuato, Mexico (communication to the Secretary*) :-Mr. Keyes's paper is very interesting to me because of my personal experience with the development of the ore-deposits of Lake Valley. Seeing that many of the important facts connected with the early history of the development of these mines are either now unknown, or have become more or less distorted, and thinking that it would be interesting as well as valuable to have these recorded as a historical supplement to Mr. Keyes's elaborate paper, I present the following narrative: In February, 1881, soon after the Atchison, Topeka & Santa Fé railroad made connection with the Southern Pacific at Denting, N. M., the Lake Valley properties were brought to the attention of New York and Philadelphia capitalists by John A. Miller, of Silver City, N. M. At that time silver was $1.10 all ounce and silver-mining was very attractive. Vast fortunes were being made in Leadville and other Colorado camps, and Tombstone was pouring out its millions. Lake Valley, like all' other mining-camps in their early history, had its drawbacks, but the railroad, then passing within 14 miles of it, mitigated many of these. The camp lay in the foot-hills of the Black range, in which the Apaches had their stronghold, and raided, when it suited their convenience, the surrounding country, killing the prospectors and pioneer settlers and stealing their cattle. This band of Indians was joined by the outlaws and desperadoes from the frontiers of Texas, Arizona, and Mexico, who collectively defied the United States soldiers, restrained, as the latter were, by the mollycoddles from the East. The brutality of the Indian raids through Arizona and New Mexico in those days would scarcely be believed now, but they stain in deep

Feb 1, 1909

By H. W. Camp

RESEARCH is defined, scientifically, as a "sys- tematic investigation of some phenomenon, and also a search for hidden treasures." Chemists tell us that the hidden treasures of petroleum are far richer than the .products which have been best known to us. However, these secrets will be discovered only through intensive and systematic, as well as scientific, industrial research. Indeed, the scope of the subject is so great that such an intensive research program should be assumed by a centralized organization supported by the petroleum industry as a whole. Such organization would assume the responsibilities for investigation of new products and development of markets for such products. Gasoline, the chief product of the petroleum industry, has become a cheap commodity. The continual un-controlled overproduction of crude petroleum, the in-tensive competitive condition in the marketing of petro-leum products and the increase of refining efficiency and installing of cracking facilities, have all combined to lower the market value of gasoline. The lower cost of gasoline has all been passed on to the purchaser in the form of lower prices so that today the most important product can scarcely be manufactured at a profit. In other fields, manufacturing industries have diversified their products when faced by a similar situation. Thus, they have been able to widen their marketing outlook. Why cannot the petroleum industry employ the same tactics ? Right now we are hearing much discussion concerning the development of a wider market for existing petro-leum products and new products for existing or prospec-tive markets. For instance, we can cite recent develop-ments for use of propane, butane, and ethylene. Butane has been found to be an efficient and inexpensive re-frigerant, especially adapted to home refrigerating sys-tems. Propane and butane fractions of natural gasoline may be shipped under pressure and may be used as a substitute for acetylene in cutting torches in connection with oxygen. There is a possibility of substituting butane for gas oil in the carbureting of coal gas, as we know that butane contains practically the gas enrich-ment as the same volume of gas oil and should prove to be a superior product for this function. Ethylene, a hydrocarbon present in cracked gases, is finding an outlet for the artificial ripening of green fruits. The following table . shows the more general use of petro-leum products as now established.

Jan 4, 1928

By William N. Poundstone

What attracts young engineering graduates into the coal industry? What do these young men expect of a career in coal mining? These questions are often asked and debated by mining men throughout the country. In order to present a comprehensive answer to them, an opinion survey was conducted at West Virginia University's School of Mines among the junior and senior classes and part of the sophomore class. The tabulation of the answers showed that the present-day mining engineering student is an older, more mature individual as compared with former years and as compared with other present-day college students. The average age of the country's record-breaking 150,000 college graduates is 24 years. Among this year's mining graduates at West Virginia University, 78% are of this age or older. Over half (54%) of those polled in the survey are married. This is com- pared to 30% as a national figure. Of those married, 38% have one child and over 6% have two children. The entire senior group covered by this survey has averaged almost three years in the armed forces. An article entitled "The Class of '49" in the June issue of Fortune magazine states that this year's class is the oldest, most mature class in history. Our survey indicates that the mining engineering students at West Virginia University are well above the average in this respect.

Jan 1, 1949

By K. J. Brondyke, P. D. Hess

Two processes have been developed for improving the quality of molten-aluminum alloys before casting. The Filtration Process. which involves passing molten metal through a packed bed of granular filter material, is a rapid means of removing finely divided particles. It has the most potential in those instances where removal of inclusions is of primary importance. The Combination Fillration-Inert Gas Fluxing Process inuolzles introduction of an inert gas so that it will diffuse countercurrent to metal flow through the filter bed of granular material. Dissolved hydrogen is removed from the metal in addition to removal of finely divided particles. The Combination Process is most useful where both inclusion removal and attainment of conistently low-hydrogen-content metal are important. Metal treated by the Combination Process is of higher and more uniform quality than heretofore attainable with prolonged chlorine fluxing. Costs of the Combination Process can, for the most part, be offset by savings derived from high recoveries and increased production of superior-quality products. IMPROVEMENT in the quality of molten-aluminum alloys is secured generally through the use of some fluxing practice in a crucible, holding furnace, or ladle involving either gaseous or solid fluxing media. Typical fluxing agents may include the gases nitrogen, argon, or chlorine used either singly or as mixtures and the solids aluminum chloride or hexachloroethane. Regardless of the fluxing means used, the primary objectives are the adequate removal of both metallic and nonmetallic inclusions and reduction of hydrogen content to an acceptably low level. The ultimate goal is to produce ingots and cast products of high quality free from inclusions and porosity. The development of ultrasonics for measurement of internal quality, tightening of quality controls, and the application of the aluminum alloys to new or different commercial fields have been responsible for an ever increasing demand for improvement of quality of both cast and fabricated products. This demand for high quality has not been restricted to any single type of product. On the contrary, the demand encompasses about the entire variety of products including those for fabrication, those to be machined, buffed, or finished for decorative purposes, and those for critical applications where both surface and internal quality is of utmost importance. In many instances products acceptable in the 40's would now be scrapped as unacceptable by these higher present-day standards. With this ever increasing demand for higher quality, it became apparent at Alcoa that conventional means of melt treatment were inadequate in many instances and new approaches were necessary. Consequently the research program was intensified with attention focused on metal treatment during transfer in order to reduce the furnace processing time to a minimum in an effort to attain the desired results at a minimum of additional expense. As a result of this intensive research program which covered numerous variations and adaptations of conventional methods in addition to new methods of melt treatment, several new processes were developed, two of which will be described here. The first of these, a method of melt filtration, was patented in February, 1959.l The second process involving combination filtration—inert gas fluxing was patented in June, 1962. 2 Other melt-treatment processes developed during this period of investigation were patented as listed.3 FILTRATION PROCESS General Description. The Filtration Process, which involves passing molten metal through a packed bed of granular filter material, is a rapid method of effectively removing finely divided particles. It is an impingement-type filter; hence the size of the particles removed from the metal are considerably smaller than the interstices of the

Jan 1, 1964

By W. O. Crosby

INTRODUCTION. THE crystalline belt of the Atlantic Seaboard, south of New York, attains its maximum breadth of 220 miles on the northern border of North Carolina; and in this State it is most widely characterized by the occurrence of gold in workable deposits. Half a dozen auriferous belts have been recognized by Nitze and Hanna.1 These are, in the main, coincident in position and trend with the NE.-SW. zones of metamorphic slates and schists, which, more than any other feature, give character to the geological map of North Carolina. The central gold-belts, accompanying the main zone of slates and associated igneous rocks, are much the more important and persistent, and may be regarded as continuous northward across Virginia and southward into South Carolina. Tile eastern belt, on the other band, is the shortest and, economically, one of the least important. Its extreme length does not exceed 25 miles, the narrow band of slaty rocks to which it belongs passing, both NE. and SW., beneath the coastal-plain formations. But, although limited in area and production, this belt is, perhaps, comparable with the central belts or any part of the sea-board crystallines in the variety of conditions under which the gold occurs. It lies chiefly in the NE. part of Franklin county and the NW. part of Nash county, on the watershed of Fishing creek and other tributaries of Tar river. The elevation is between 400 and 500 ft. ; and the Tertiary peneplain has here an exceptionally perfect development, the reliefs separating the slightly incised stream-courses consisting of broad, flat-topped peneplain remnants, bounded by gentle lateral slopes.

Mar 1, 1908

By E. Gilpin

The following notes may serve to bring before your Institute an idea of the iron-ore resources of Pictou County. Enough work has been done to permit an estimate to be formed of their quality and probable extent. As yet the systematic mining and smelting of ironore in Nora Scotia is confined to the operations of the Steel Company of Canada, in Colchester County. Although the locality I am about to describe appears, in many respects, well adapted to iron smelting, etc., no attempts have yet been made to begin work. Nora Scotian capital is more readily turned to lumbering, fishing, and shipping ventures; and such an investment appears equally foreign to the rest of the Dominion. I need not, however, go further into this part of the subject, and can only hope that my notes may prove serviceable as indicating a probable field for future development. The accompanying map shows the position of the harbor of Pictou relative to the coal and iron-ore fields, and to the railways which intersect them. The branch of the Intercolonial Railway, running from Truro to Pictou, forms the western boundary of the iron-ore district, which extends beyond the point where the New Glasgow and Cape Breton Railway crosses the French River. The iron-ore district may be roughly described as a triangle formed by the ore-outcrops and the two railways, the former making the base, and the latter the sides of the triangle, the apex resting on the coal-field at New Glasgow. The drainage of the country is toward the Gulf of St. Lawrence, through the Middle, East, Sutherland's, and French rivers; and the surface is undulatory, seldom exceeding two hundred feet above the sea-level, except in the district lying between Glengarry and the upper waters of the French and Sutherland's rivers, where a maximum height of about five hundred feet is reached at several points. Geologically speaking, the district embraces two divisions, the Carboniferous and the Silurian, the latter resting on strata provisionally considered to be of pre-Cambrian age. As no geological

Jan 1, 1886