Search Documents

By J. B. Newkirk

Results of a Debye-Scherrer X-ray investigation are given which show that the order-disorder transformation is a first-order or heterogeneous reaction in Cu-AU alloys with compositions near CuAu. Evidence was found for conventional tie-line segregation across a usual type of two-phase field separating the ordered and disordered fields in the Cu-Au equilibrium phase diagram. The horizontal and vertical widths of the two-phase fields are about 3 atomic pct and 20°C, respectively, at 43 and 54 atomic pct Au. No evidence for the existence of an ordered structure based on a stoichiometric composition of Cu3Au2 could be found. ALTHOUGH the modern theories relating the de-Agree of order of binary alloys to temperature and composition have met with considerable success, the nature of the transformation from the disordered state to the ordered state and vice versa has never been well understood. It has been assumed by some' that this is a second-order transformation, that is, a homogeneous change of state. Others2 hold that the transformation is first-order and that the effects characteristic of heterogeneous phase transformation apply. Since this subject is discussed in detail in a recent paper,' the arguments will not be repeated here. The present paper summarizes an experiment which was designed to distinguish between these two viewpoints for the case of Cu-Au alloys near the composition CuAu. The Cu-Au system is an important one because it furnishes prototype alloys, the behavior of which has formed the basis of much of the present-day order-disorder theory. It has recently been shown- hat in alloys near Cu3Au there is a temperature range within which the ordered and disordered states coexist in equilibrium and are distinguishable as separate phases. Therefore, the transformation must be first-order for these alloys. A similar demonstration for alloys near CuAu, however, has been lacking. Experimental Method Essentially the experiment consisted of equilibrating Cu-Au samples at various temperatures, quenching them in water to retain the high temperature states, and then examining them at room temperature for the coexistence of the ordered and disordered structures. The thermal gradient method of heat treatment- as used because it was important that all temperatures over the transformation range should be represented in the test. Briefly, this method consisted of holding a wire of the desired composition, sealed under vacuum in Pyrex, in a known temperature gradient for a long enough time to allow each part of the wire to assume the crystal structure characteristic of the temperature at which it was held. The temperature gradient was produced by inserting into an ordinary wire-wound cylindrical laboratory furnace, an 18 in. length of 1/8 in. ID ceramic tube which was heavily wrapped with asbestos. The furnace power was controlled by a Tag-liabue Celectray controller and a chromel-alumel thermocouple with the junction located on the heating elements. During the equilibrating treatment the widest variation of temperature within the gradient tube was approximately 4°C at the highest temperature. The temperature at various places within the tube was determined, before inserting

Jan 1, 1954

By G. K. Manning, A. R. Elsea, A. B. Westerman

INTRODUCTION A CONSIDERABLE number of high-temperature alloys, that is, alloys which have load-carrying ability at elevated temperatures, have been developed on an empirical basis. In order to determine why these alloys possess this particular ability, a project was started at Battelle Memorial Institute on the fundamental factors promoting high-temperature strength of alloys. At the time of inception of this study, the cobalt-base alloy, Vitallium, was widely used because of its good high-temperature properties. One phase of this study was to include an investigation of the structures observed in Vitallium after various heat treatments. However, before investigating the structural features of Vitallium, it appeared logical to examine the phase diagrams of the related binary systems in order to develop information as to which phases- might be present in Vitallium. A preliminary survey of the pertinent alloy systems was made, with particular emphasis on the cobalt-chromium system, which is the base for the Vitallium series of alloys. The early work of Lewkonja1 and Guertler2 indicated that cobalt and chromium are completely miscible in the liquid state, and, within a narrow temperature range, in the solid state; that the liquidus shows a minimum; and that the alloys containing 45 to '85 pct chromium undergo a transformation at 1200 to 1250°C. More recently, Wever and Haschimoto,3 Wever and Lange,4 and Matsunaga5 carried out experimental work which led to the diagrams shown in Fig I and 2. Both diagrams are based on thermal analysis, metallographic, magnetic, and dilatation data; in addition, X ray diffraction results were used by Wever and Haschimoto, and electrical resistance measurements by Matsunaga. It is apparent from a comparison of the two diagrams that there was a difference of opinion as to the locations of the boundaries of the various phases, and as to the existence of a phase containing approximately 47 pct chromium. With these exceptions noted, it might be pointed out that the two diagrams are similar, and that, in general, any particular reaction which is shown on both diagrams occurs at a lower temperature on the Matsunaga diagram than on that of Wever-Haschimoto-Lange. Thus, in view of the gaps in the data and the questionable features in the published diagrams, it appeared desirable to start the fundamental study of Vitallium by determining the diagram for the cobalt-chromium system. EXPERIMENTAL WORK For the convenience of the reader, the diagram as determined by the present investigation is presented in Fig g. The liquidus and solidus data for the low-chromium alloys were taken from the work of Wever and Haschimoto,3 while the, melting point for pure chromium is the

Jan 1, 1948

By Edward Keller

About a dozen years ago the art of bessemerizing copper- * matte, brought to these shores from France, was first established at the smelter, in Butte, Montana, of the Parrot Silver and Copper Company, which had bought the process from Mr. Manhks, the inventor. Through the efforts of Mr. J. E. Gaylord, general manager, and Mr. A. J. Schumacher, snperintendent,, assisted by an able staff, the new method rapidly underwent, at the Parrot establishment, an evolution towards higher perfedion, and within a few years its success and its advantages were so marked that all the great works in the west followed in the footsteps of this pioneer. The converter-process has now practically superseded the reverberatory-process in this country. The latter will undoubtedly, in a not very distant future, be relegated to metallurgical history. The writer has availed himself of what was perhaps the last chance to make comparisons of the two methods, working practically on the same material on an extensive scale, the reverberatory process being that of the Baltimore Copper Smelting and Rolling Company,* while the converter-process is that of the Anaconda Copper Company—both using the matte from the latter company's works in Anaconda, Montana. For the greater portion of the material considered in this paper, the writer is indebted to the two companies. In order to understand the difference of behavior of the several elements, and the difference of the copper produced in the two processes, it is best to study and follow those elements

Jan 1, 1899

By Frank Alfred Fahrenwald

Discussion of the paper of FRANK ALFRED FAHRENWALD, presented at the New York meeting, February, 1916, and printed in Bulletin No. 109, January, 1916, pp. 103 to 149. F. A. FAHRENWALD, Cleveland, Ohio (communication to the Secretary*).-Since the publication of my paper in the January Bulletin, (which was largely a metallographic treatise), I have been questioned regarding two points referred to therein. One of these is that which deals with the application I have made, p. 119, of the equation for melting pressures which correspond with different working temperatures. The other refers to the statement, p. 137, that "Prolonged heating at relatively low temperatures gave fewer and larger crystals and crystals of different sizes, while a flashing at higher temperatures gave a very fine and uniform crystalline structure, which was much' to be preferred." Especial emphasis was not placed upon either of these two factors, for each seemed perfectly logical and obvious. As they do not seem to be self-explanatory, I will supplement with those portions of my notes which were purposely omitted from the manuscript submitted for publication. A few practical illustrations may serve as evidence in support of the first of these, but it must be understood that in this work the "amorphous theory" is considered as being sound, and that it is assumed that metals allow of distortion, without fracture, by virtue of the formation of slip surfaces, accompanied by the transformation of crystalline material to the, amorphous phase. Effect of Pressure.-In all forging, rolling, and drawing operations, it is known that specimens of small cross-section may be worked at a lower temperature than can be used for the same material in much greater mass and sectional area. In -the larger pieces the maximum pressure is brought to bear upon the material near the surface, so that the interior is not subjected to great pressure, but to, a stress more nearly tensile, or shearing, so only the surface is subjected to the critical melting pressure. In the case of wires which draw hollow, the center is subjected to practically a tensile stress which breaks it, while the surface skin draws perfectly, due to the enormous "flowing" pressure exerted upon it by the surface of the draw-plate.

Jan 5, 1916

By Charles J. McMahon

In a recent paper, Floreen and Hayden report that additions of the noble metals iridium, rhodium, ruthenium, and platinum to Fe-C alloys containing 0.03 to 0.08 wt pct C act to significantly reduce the ductile-to-brittle transition temperature in a notched-bar impact test. They compare these results with the similar, well-known effects of nickel and manganese additions, and they note that this supports the hypothesis that addition of austenite stabilizers enhances notch toughness. Although not attempting to offer an explanation for this, they suggest that it might be found in an alteration of the bonding characteristics of the bcc lattice of iron by additions of elements which tend to stabilize the fcc lattice. While this suggestion appears to have some merit, it should perhaps be held in abeyance until two more likely possibilities have been explored. It is now fairly clear that the beneficial effect of manganese derives from its ability to promote a globular carbide morphology instead of the platelike form found in grain boundaries and pearlite patches in Fe-C al10~s.' Previous work14 has also shown that cleavage fracture in Fe-C alloys of the type tested by Floreen and Hayden originates almost exclusively in the cracking of cementite platelets, and that the ductile-brittle transition temperature is very sensitive to the volume density and size of these carbides. Treatments which lead to development of nonlamellar carbides or fine dispersions of carbides, such as quenching and tempering or appropriate alloy additions, promote toughness by removing the primary mode of cleavage initiation. The effectiveness of manganese in this regard has long been known. Nickel appears to behave in a similar manner, though the effect is perhaps not as dramatic as with manganese.15 However, nickel additions do lead to a definite refinement of ferrite grain size following a given transformation heat treatment, and this in itself acts to greatly enhance notch toughness.'' (The grain sizes of the various heats tested by Floreen and Hayden were not reported, so it is not known how much influence this factor exerted in their results.) In conclusion, it is suggested that one should consider the well-established effects of alloying elements on carbide morphology and ferrite grain size before resorting to more complex possibilities, such as modification of interatomic bonding.

Jan 1, 1969

By L. O. Howard

What was perhaps the first attempt at basic converting in the Southwest was made by the late Charles F. Shelby at Cananea early in 1907, when he removed the acid lining from one of the 8 by 12-ft. barrel-type converters then in use at the reduction works of the Cananea Consolidated Copper Co. and substituted a lining of one course of magnesite brick. In this shell, he blew 21 taps (about 180 tons) of matte to white metal before the brick gave out along the tuyhre line. In every case, the white metal so made was transferred and blown to copper in other converters. The cost of the lining was $700 and Mr. Shelby gave up the experiment as impracticable. No further serious effort to bessemerize copper mattes in a vessel having a more or less permanent lining of basic brick was made by any of the large copper smelters in the Southwest until some months after Messrs. Peirce and Smith had brought the question permanently before the public, and had proved it to be a metallurgical and financial success by their work at Baltimore and Garfield. Early in 1911, the Cananea Consolidated Copper Co. had in operation at its reduction works at Cananea, Mex., several 8 by 12-ft. barrel-type converters lined with magnesite brick which had previously been operating with acid linings. In the 18 months following, these converters produced 50,000 tons of copper. In June, 1912, this company installed the first of its new equipment of six stands of electrically operated 12-ft. Great Palls type converters, and shortly afterward discontinued the use of the smaller shells. In September, 1911, the Consolidated Kansas City Smelting & Refining Co. had installed at its El Paso plant two 10 by 26-ft. Peirce-Smith converters. Later, in March, 1913, one standard Great Falls type converter was added. About the time the Peirce-Smith converters were going in at El Paso, the Calumet & Arizona Mining Co. was experimenting with basic linings in 7-ft. by 10-ft. 6-in. barrel converters at its plant in Douglas, Ariz. These efforts were sufficiently successful to enable the plant to "handle the total output of copper in these small shells until the standard Great Falls converters were substituted in June, .1914.

Jan 1, 1917

By C. A. Stetefeldt

In my paper on "The Consumption of Fuel in the Taylor Gas-Producer Plants at the Aspen and Marsac Mills" (Trans., xxiii., 134), I mentioned that in the plant which I had designed for the Ontario mill, the gas-tubes were to be covered with thin, corrugated sheet-iron, over which a coating of asbestos-magnesia would be spread in order to effect a good insulation and keep the gas as hot as possible. At the Ontario mill, two Stetefeldt furnaces and two revolving driers are fired with gas. One furnace is connected with a Taylor producer of 5 feet diameter, and the other furnace and the two driers are heated by the gas from a Taylor producer of 7 feet diameter. In the latter case the gas-tubes are necessarily somewhat long, and the cleaning of them takes time. In order to prevent overheating of the tubes during that operation, it has been found advantageous not to provide them with an insulating covering. If a tube becomes red-hot at any place by the burning of soot, this is at once observed, and the tube is closed until it cools down. The tubes con-

Jan 1, 1895

By J. V. Richards

(Canal Zone Meeting, November, 1910,) THE Altar district, State of Sonora, Mexico, is for the most part a desert with but little rain-fall and few running streams. On account of this scarcity of water it is necessary for the natives to " dry-wash" the placer-gravel, and the object of the present paper is to describe some of the more common Mexican dry-washing devices. My observations were confined to a property known as Las Palomas placers, 15 miles from the Gulf of California and about 150 miles south of the United States border; a brief description of which property may be of interest as illustrating what is, perhaps, a typical Sonora dry placer. It is said that as long as a century ago the Yaqui Indians discovered rich cement-gravel, known as argo masa, at Las Palomas, and that there has been a more or less steady production of gold from the property ever since. The argo masa is a fairly-coarse gravel, the pebbles being quite firmly held together with a lime cement. Gold is scattered through this cement in particles ranging from fine specks to pieces several grams in weight, and occasional large nuggets are encountered. The contents vary so widely that it is difficult to estimate the average value, but returns of from $10 to $50 per cubic yard are common, and it is doubtful if the Indians considered anything less than from $4 to $5 a yard as "pay dirt." This argo masa occurs in channels varying in thickness from a few inches to several feet, and in width up to 300 ft.. These channels are continuous and are probably ancient stream-beds. They are for the most part covered with an over-burden of a more recent gravel, varying from 30 to 50 ft. thick, and the fact that this over-burden contains values as high as $1.50 per cubic yard, and yet was not worked by the Indians, shows that their idea of what constituted pay-ground was high.

Apr 1, 1911

By R. J. Stoehr, F. Howell

Since the ore mined in the Grants-Ambrosia Lake uranium area is taken from a water-saturated sandstone formation, part of the milling operation includes a drying process. The authors discuss the merits and disadvantages of two methods: natural drying and mechanical gas-fired drying; operating and cost data are included. In the Grants-Ambrosia Lake uranium area, approximately 7000 tons of ore are mined each day from a water-saturated sandstone formation. This ore is sampled and treated at four separate milling operations. Prior to the design and initial construction of the milling facilities, very little was known as to the physical properties of the ore which would be handled in the sampling and crushing facilities at the mills. All four mills initially were constructed without ore-drying facilities. As mining proceeded, it was determined that, even after drying the ore in place by use of drainage development underground, the moisture content of the ore as hoisted averaged approximately 18 pct. Actually, some of the mines produced ores which resembled cream-of-wheat in character and had a moisture content in excess of 24 pct. Each of the four mills had a differently designed sampling and crushing plant; therefore, the moisture content of the ores had varying adverse effects upon the operation of the plants. It was determined after some experience that most of the sampling and crushing facilities could not economically handle ore if the moisture content was greater than 10 pct—one operator considers 12 pct moisture as a maximum. In all of the plants, moisture content over 8 pct increases costs to some extent. In addition to the added sampling and crushing costs, some of the mills were located 15 to 20 miles from the mines and the high moisture content of the ores increased the haulage costs from the mine to the mill. It was generally conceded that it was necessary to employ some method to reduce the moisture content of the ore prior to sampling. Several methods were considered: 1) natural drying at the mine site, 2) mechanical gas-fired drying at the mill site, 3) mechanical gas-fired drying at the mine site, 4) radiant heating on concrete clabs, and 5) infrared shed drying. After preliminary investigation all possibilities but natural drying and mechanical gas-fired drying at the mill site were eliminated. NATURAL DRYING A cooperative feasibility study was conducted on the natural drying method. This study indicated the following: 1) During summer months May through September, ore piled 4-ft deep would dry from +20 to +10 pct HzO in 30 days with no mechanical turning. 2) In the first four days after piling a reduction of 5 to 7 pct total moisture content was accomplished by drainage and absorption of the water into the underlying ground on which the ore was piled, providing the ground surface absorption rates approached 10 gal per sq ft per day. After the first four days the decrease of moisture caused by drainage was practically nonexistent. 3) In the summer months drying by evaporation amounted to approximately 0.1 pct decrease in total moisture per day and mechanical turning of the ore could increase this as much as three times. 4) Climatic conditions of the area indicated that: a) Air temperatures averaged 64' May, June, July, August, September; 41" October, November, December, March, April; 31" January, February. b) Average rain fall was 10 in. with 40 pct of this occurring during July and August. c) Only on very rare occasions were there over five consecutive days with below freezing temperatures. d) The annual evaporation rate was approximately 75 in. On the basis of this study, two of the mill operations decided to attempt to meet the moisture specifications by natural drying supplemented by mechanical turning. The other two operations decided upon rotary gas-fired drying at the mill site. The natural drying method has been quite successful in practice. The ore running approximately 18 pct moisture is trucked from the head frame and piled in rows about 6 ft wide, 3 1/2 ft deep, 5 feet apart during the months of May through September. In approximately 30 days this ore will

Jan 1, 1961

By W. D. Kruger

Methods for analyzing flooding or cycling projects by means of two-dimensional flow calculations are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The accuracy of such analyses depends on the basic reservoir data employed, especially the absolute permeability distribution in the reservoir; however, absolute permeability data normally are determined from well flow tests and/or core measurements and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. A calculation procedure is presented for determining the areal permeability distribution in the reservoir. Use of the procedure allows verification of the basic reservoir data through the matching of past reservoir conditions, thereby providing proper data for reliable predictions of future operations. The calculation procedure is a numerical technique based on a mathematical model of the reservoir and is designed for solution by means of an electronic digital computer. Results from field application of this procedure are presented. Permeability distributions from measured data are compared to those calculated to indicate the need for the analysis. Comparisons of field-measured and calculated pressure distributions are given to establish the validity of the calculation procedure. The conclusions of this paper are (I) use of the calculation provides data that allow a match of past reservoir conditions and thus reliable prediction of future operations; and (2) the procedure should, where applicable, be used to provide adequate reservoir data for use in two-dimensional flow calculations and related reservoir analyses. INTRODUCTION One means of providing more precise engineering control over reservoir operations during all stages of depletion is to develop some type of model to simulate the reservoir, using information developed from the behavior of the prototype to predict the performance of the actual reservoir. The use of mathematical rather than physical models for this purpose has been gaining in importance recently because of the application and availability of electronic computers. Mathematical models avoid instrumentation difficulties and allow easier handling of large-scale problems. At present, analyses employing two-dimensional models are common, and thought is being given to the use of models in three dimensions. The use of multi-dimensional models is necessary to show not only what is occurring in the reservoir, but also where in the reservoir the phenomena of interest are taking place. Methods for analyzing flooding or cycling projects by means of two-dimensional numerical models are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The applicability of numerical models and the results of using such analyses have been presented through field examples. The references indicated here discuss fully the data necessary to build the mathematical reservoir model and the way the model is used to study or predict the future performance of the reservoir. The accuracy of the analysis of such projects depends on the basic reservoir data employed in the construction of. the model. In order to be sure the model represents the reservoir, it must be used to match some known set of reservoir conditions, i.e., to match past reservoir performance. The accuracy of the model is directly dependent upon the absolute permeability distribution in the reservoir; however, absolute permeability data are normally determined from well flow tests and/or core measurements, and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. There is always the need for better data and for verification of existing data. The purpose of this paper is to show the use of the mathematical model to match past performance in flooding or cycling projects, the use of numerical techniques to adjust the basic absolute permeability data if necessary so that a match is obtained, and in this way to generate the effective areal permeability distribution of the reservoir. A review of the basic concepts of the numerical model will be given, followed by a discussion of the data-adjusting technique for matching past performance. TWO field examples will be cited to show

By Raymond Mancha

A test of any fan requires the determination of such data as fan pressure, air volume handled by the fan, and power input to the fen shaft. When testing operating mine fans of the centrifugal type, test methods have been employed, for the sake of convenience, that permit great latitude in detail of procedure resulting in wide variance in results by different investigators. Some controversial aspects of field fan testing are the result of past failure to define clearly the various forms of fan pressure and to a lack of understanding of the accurate procedure for the measurement thereof. Also, the anemometer for air-volume measurement, although convenient, if carelessly used and maintained is subject to a wide error range with variation in method of application and in instrument accuracy. The appearance of the axial-flow type of mine fan offers the possibility of refinements in field testing that were impractical with the centrifugal fan. First of all, the fan inlet and outlet are more sharply defined, giving closer agreement as to just where the fan begins and ends; thus there is less disagreement as to the proper location for measurements of fan pressure. The area of passage into the inlet of an axial-flow mine fan usually constricts, causing high air velocities with accompanying steadiness of flow. Thus the fan inlet offers an ideal location for accurate air-volume measurements with the pitot tube, the proper use of which is well established by code. Thereby the controversial aspects of such measurements are eliminated. Use of the Pitot tube also facilitates a more accurate measure of fan pressure, since the individual pressures measured can be properly weighted, as will be explained later. Determination of power input to the axial-flow mine fan operating in the field is subject to the same inaccuracies as with the centrifugal fan if the axial-flow fan is also belt driven. However, because of the higher rates of rotation usual with axial-flow fans, direct-driven units are more numerous and it is unnecessary to assume a drive efficiency, thus eliminating one possible source of error. It is the purpose of this paper to define and explain the various types of pressure measurements involved in a field test of an axial-flow mine fan, and to further explain the proper use of the Pitot tube when measuring pressures and volumes. DefinitioN of Fan Pressures The two fan pressures most commonly discussed are fan total and fan static pressure, each of which has the same meaning regardless of whether the fan is blowing, exhausting, or blowing and exhausting, as in the case of a fan with ducts connected to both outlet and inlet. Fan total presscre is the amount by which the total pressure of the air delivered by the fan exceeds the total pressure of the air received by the fan. This pressure is a measure of the maximum amount of the work done on the air by the fan that is available for external use.

Jan 1, 1942

By Raymond Mancha

A test of any fan requires the determination of such data as fan pressure, air volume handled by the fan, and power input to the fen shaft. When testing operating mine fans of the centrifugal type, test methods have been employed, for the sake of convenience, that permit great latitude in detail of procedure resulting in wide variance in results by different investigators. Some controversial aspects of field fan testing are the result of past failure to define clearly the various forms of fan pressure and to a lack of understanding of the accurate procedure for the measurement thereof. Also, the anemometer for air-volume measurement, although convenient, if carelessly used and maintained is subject to a wide error range with variation in method of application and in instrument accuracy. The appearance of the axial-flow type of mine fan offers the possibility of refinements in field testing that were impractical with the centrifugal fan. First of all, the fan inlet and outlet are more sharply defined, giving closer agreement as to just where the fan begins and ends; thus there is less disagreement as to the proper location for measurements of fan pressure. The area of passage into the inlet of an axial-flow mine fan usually constricts, causing high air velocities with accompanying steadiness of flow. Thus the fan inlet offers an ideal location for accurate air-volume measurements with the pitot tube, the proper use of which is well established by code. Thereby the controversial aspects of such measurements are eliminated. Use of the Pitot tube also facilitates a more accurate measure of fan pressure, since the individual pressures measured can be properly weighted, as will be explained later. Determination of power input to the axial-flow mine fan operating in the field is subject to the same inaccuracies as with the centrifugal fan if the axial-flow fan is also belt driven. However, because of the higher rates of rotation usual with axial-flow fans, direct-driven units are more numerous and it is unnecessary to assume a drive efficiency, thus eliminating one possible source of error. It is the purpose of this paper to define and explain the various types of pressure measurements involved in a field test of an axial-flow mine fan, and to further explain the proper use of the Pitot tube when measuring pressures and volumes. DefinitioN of Fan Pressures The two fan pressures most commonly discussed are fan total and fan static pressure, each of which has the same meaning regardless of whether the fan is blowing, exhausting, or blowing and exhausting, as in the case of a fan with ducts connected to both outlet and inlet. Fan total presscre is the amount by which the total pressure of the air delivered by the fan exceeds the total pressure of the air received by the fan. This pressure is a measure of the maximum amount of the work done on the air by the fan that is available for external use.

Jan 1, 1942

By Raymond Mancha

A TEST of any fan requires the determination of such data as fan pressure, air volume handled by the fan, and power input to the fan shaft. When testing operating mine fans of the centrifugal type, test methods have been employed, for the sake of convenience, that permit great latitude in detail of procedure resulting in wide variance in results by different investigators. Some controversial aspects of field fan testing are the result of past failure to define dearly the various forms of fan pressure and to a lack of understanding of the accurate procedure for the measurement thereof. Also, the anemometer for air-volume measurement, although convenient, if carelessly used and maintained is subject to a wide error range with variation in method of application and in instrument accuracy. The appearance of the axial-flow type of mine fan offers the possibility of refinements in field testing that were impractical with the centrifugal fan. First of all, the fan inlet and outlet are more sharply defined, giving loser agreement as to just where the fan begins and ends; thus there is less disagreement as to the proper location for measurements of fan pressure. The area of passage into the inlet of an axial-flow mine fan usually constricts, causing high air velocities with accompanying steadiness of flow. Thus the fan inlet offers an ideal location for accurate air-volume measurements with the Pitot tube, the proper use of which is well established by code. Thereby the controversial aspects of such measurements are eliminated. Use of the Pitot tube also facilitates a more accurate measure of fan pressure, since the individual pressures measured can be properly weighted, as will be explained later. Determination of power input to the axial-flow mine fan operating in the field is subject to the same inaccuracies as with the centrifugal fan if the axial-flow fan is also belt driven. However, because of the higher rates of rotation usual with axial-flow fans, direct-driven units are more numerous and it is unnecessary to assume a drive efficiency, thus eliminating one possible source of error. It is the purpose of this paper to define and explain the various types of pressure measurements involved in a field test of an axial-flow mine fan, and to further explain the proper use of the Pitot tube when measuring pressures and volumes. DEFINITION OF FAN PRESSURES The two fan pressures most commonly discussed are fan total and fan static pressure, each of which has the same meaning regardless of whether the fan is blowing, exhausting, or blowing and exhausting, as in the case of a fan with ducts connected to both outlet and inlet. Fan total pressure is the amount by which the total pressure of the air delivered by the fan exceeds the total pressure of the air received by the fan. This pressure is a measure of the maximum amount of the work done on the air by the fan that is available for external use.

Jan 1, 1942

By T. H. Courtney, G. W. Pearsall, J. Wulff

The mechanism, of the decrease in transition temperature of Nb3Sn was studied. Presintered Nb3Sn powder compacts were heated in a dynamic vacuum at elevated temperatures. Loss of tin resulted from these heat treatments and transition temperature as a function of tin loss was discontinuous at a critical value of tin loss. In general, decreases in transition temperature were correlated with deviations from AS a class, the A15 structure-type (also known as Cr3O or ß W) compounds have the highest superconducting transition temperatures.' In this class are stoichiometry and presence of vacancies in niobium sites. The effect of vacancy distribution on the physical properties of Nh3Sn is considered. It is concluded that the close-packed atomic A chain in the A3B A15 structure must be preserved both in coutinuity and direction if good superconducting properties are to he obtained. tempting to associate these high transition temperatures with the most unique crystallographic feature of the A3B structure: the three close-packed, orthogonal chains of A atoms.'0"' There are at least three principal mechanisms by which the perfection of these "A-atom chains" could be interrupted: changing stoichiometry, inducing disorder, or introducing vacancies. Departures from stoichiometry in either direction in V3Ga lower the transition temperature.7'8 In niobium-

Jan 1, 1965

By J. C. Wright

A practical program of education for workers of the mining industries is being formulated by the Federal Board for Vocational Education in cooperation with the states in which this industry is a dominant one. The Federal Government last year passed a law, known as the Federal Vocational Education Act, that provides for the promotion of vocational education and for cooperation with the states in the promotion of such education in agriculture and trades and industries and in the preparation of teachers of vocational subjects. More than 1,000,000 men in the continental United States are employed in mines and quarries. The following table, from the 1910 Census Report, shows the relative importance of mining and manufacturing pursuits: Manfactures Mines and quaRRies Employees.......... 7,405,313 1,109,410 Capital............. $18,428,269,706 53,380,525,841 Value of product..... $20,672,051,870 $1,238,410,322 Of the more than 1,000,000 men employed in mining, almost three-fourths are engaged in the production of bituminous and anthracite coal; one-fifth, in the production of copper, iron, lead, zinc, and other metals; and the remainder in getting out structural and miscellaneous materials from quarries. The meeting of the needs of the coal-mining industry, therefore, is the problem of greatest importance in the point of numbers to be served. Moreover, the dangers in coal mining are greater than in metal mining. Practically all states have set up educational and technical standards for the position of foreman, boss, superintendent, etc., and every applicant for these positions must have a certificate of competency. The qualifications, too, are becoming increasingly difficult in the field of technical information. In some states, every miner must have a certificate, which is issued by the mine examining board only after an oral examination. Did these state laws not call for definite and comprehensive plans for the vocational education of men in the mining regions, the conditions

Jan 1, 1919

By Robert H. Hafner, Irvin R. Kramer, Stewart L. Toleman

IN his paper on the calculation of hardenability from chemical composition, Grossmann1 discussed the effect of most of the alloying elements used commercially. The purpose of the work reported in this paper was to determine the effect of several other elements on hardenability-arsenic, antimony, beryllium, cobalt, columbium, germanium, tellurium, tin, aluminum, and titanium-and to extend the range of composition of some of the elements studied by , Grossmann-chromium, copper, manganese, molybdenum, nickel and silicon. EXPERIMENTAL METHODS To determine the effect on hardenability, suitable amounts of the alloying elements were added to experimental heats and the hardenability determined by means of end-quenched hardenability specimens. The steels were melted in a high-frequency induction furnace with a basic crucible, using ingot iron as a base for some of the heats and S.A.E. 1015 for others. The alloying additions were made as ferroalloys or as metal, depending on the ' alloying element. Hundred-pound heats were split and poured into square, tapered, cast-iron ingot molds with hot tops. Aluminum was not used as a deoxidizer in most of the heats. The ingots were homogenized for 12 hr. at 1260°C. (2300°F.) , and forged into rounds of 1 ½ in. diameter. These bars were normalized twice from 840°C. (1550°F.) before machining into Jominy bars. The composition of the steels was deter- [ ] mined in most cases by samples taken from the end-quench hardenability specimen. As suggested by crafts,2acid-soluble

Jan 1, 1943

By Stewart L. Toleman, Robert H. Hafner, Irvin R. Kramer

In his paper on the calculation of harden-ability from chemical composition, Gross-mannl discussed the effect of most of the alloying elements used commercially. The purpose of the work reported in this paper was to determine the effect of several other elements on hardenability—arsenic, antimony, beryllium, cobalt, columbium, germanium, tellurium, tin, aluminum, and titanium—and to extend the range of composition of some of the elements studied by Grossmann—chromium, copper, manganese, molybdenum, nickel and silicon. Experimental Methods To determine the effect on hardenability, suitable amounts of the alloying elements were added to experimental heats and the hardenability determined by means of end-quenched hardenability specimens. The steels were melted in a high-frequency induction furnace with a basic crucible, using ingot iron as a base for some of the heats and S.A.E. 1015 for others. The alloying additions were made as ferroalloys or as metal, depending on the alloying element. Hundred-pound heats were split and poured into square, tapered, cast-iron ingot molds with hot tops. Aluminum was not used as a deoxidizer in most of the heats. The ingots were homogenized for 12 hr. at 1260°C. (23oo°F.) and forged into rounds of I½ -in. diameter. These bars were normalized twice from 840°C. (I55o°F.) before machining into Jominy bars. mined in most Cases by samples taken from the end-quench hardenability spedmen. AS suggested by Crafts,2 acid-soluble (8

Jan 1, 1944

By Robert H. Hafner, Irvin R. Kramer, Stewart L. Toleman

In his paper on the calculation of harden-ability from chemical composition, Gross-mannl discussed the effect of most of the alloying elements used commercially. The purpose of the work reported in this paper was to determine the effect of several other elements on hardenability—arsenic, antimony, beryllium, cobalt, columbium, germanium, tellurium, tin, aluminum, and titanium—and to extend the range of composition of some of the elements studied by Grossmann—chromium, copper, manganese, molybdenum, nickel and silicon. Experimental Methods To determine the effect on hardenability, suitable amounts of the alloying elements were added to experimental heats and the hardenability determined by means of end-quenched hardenability specimens. The steels were melted in a high-frequency induction furnace with a basic crucible, using ingot iron as a base for some of the heats and S.A.E. 1015 for others. The alloying additions were made as ferroalloys or as metal, depending on the alloying element. Hundred-pound heats were split and poured into square, tapered, cast-iron ingot molds with hot tops. Aluminum was not used as a deoxidizer in most of the heats. The ingots were homogenized for 12 hr. at 1260°C. (23oo°F.) and forged into rounds of I½ -in. diameter. These bars were normalized twice from 840°C. (I55o°F.) before machining into Jominy bars. mined in most Cases by samples taken from the end-quench hardenability spedmen. AS suggested by Crafts,2 acid-soluble (8

Jan 1, 1944

By S. E. Bretherton

Most metallurgists appreciate the great need of a process for the extraction and recovery of valuable metals from complex ore, where the presence of one metal increases the cost of extracting the other rnetals to such an extent that not any of the metals can be extracted at a profit. We need only refer to some of the mines in Colorado, Utah, and New Mexico, where oxidation has taken place and the sulphur, zinc, copper, and some of the iron and other metals have been leached out, large bodies of oxidized ore remaining, rich in lead, silver, and sometimes gold. These metals have been concentrated by the removal of the other metals, leaving a very desirable ore for treatment in the blast-furnace for the production of lead bullion, and recovery of the silver and gold. If lead is not present, the gold and silver metals are usually recovered by some method of milling, or the ore is shipped to a smelter, where it is mixed with lead ore or copper-iron sulphide ore from some other mine. In these same mines, when developed to greater depth below the leached or oxidized zone, the ore is found to contain the original mixture of sulphur, zinc, copper, etc., added to, or I should say left with, the lead, silver, and gold values; but instead of adding to the value of the ore, the presence of these elements, especially zinc, makes the copper, silver, and gold of less value, and often worthlees. Such was the experience of the oldest mines in Leadville,.Colo., until methods of mechanical separation of the lead from the zinc were developed sufficiently to allow of some profit by the making of a concentrate rich in zinc to be shipped to the zinc smelter, and sometimes a lead concentrate which could be shipped to the lead smelter; but even in these cases the waste of the different metals is a very serious matter. In the very best concentrating plants some zinc will be left in the lead concentrate, to be lost and to give considerable trouble in the lead-smelting furnace. On the other hand, some of the lead, with a large percentage of the copper and silver, will follow the zinc into the zinc concentrate, to be, perhaps, recovered by smelting the cinder or clinker left in the re-

Jan 1, 1915

By H. R. Hoffman

SINCE slag is a necessary product of the reactive oxygen additions necessary to the present-clay quality steelmaking, the study of the control of its volume is being attempted. With other varying factors that may affect the volume of slag kept as nearly constant as possible, the object of this investigation is to determine what effect the one factor of varying the amounts of iron-ore additions and the time of the additions may have upon the volume of slag in producing an acid electric steel heat.

Jan 1, 1947