Search Documents

By C. R. Dale

The need for instruments to measure the movement of fluids and gas in wells has been recognized by engineers for many years. Information regarding flow in the producing interval has a direct bearing on completion practices in new wells and also provides information on the production characteristics of the well. Many hours of engineering time are spent in planning and completing wells but knowledge as to whether or not the original planning has produced the desired results has not always been complete. Many questions such as the following often arise: Why is it that two wells are completed under supposedly identical conditions, yet one well is a good one and the other is a poor one? Are the sands that look the best on the electric log contributing to the production? These and many other conditions in the producing well need to be under- stood in order to develop more efficient production practices and to improve on methods of completing new wells. It is the purpose of this paper to briefly describe one type of instrument, outline the methods of running the equipment and show the results of surveys made under various conditions. With an understanding of the use of this type of survey its importance can be evaluated in relation to the problems encountered by the operator. DESCRIPTION OF INSTRUMENT The instrument is a velocity recorder employing a clock-controlled 16mm film for recording the rpm of an extremely sensitive rotor which is rotated by the flow of fluids or gas in a well. The helical-vaned rotor and shaft, weighing one-half of one ounce are an integral unit exposed to the well fluids and are the only moving parts not enclosed in the fluid-tight housing. No packing or fluid seal of these parts is necessary and the shaft is mounted top and bottom on special jeweled bearings. Fig. A is the lower part of the instrument showing rotor and shaft with the protecting housing sleeve removed. The rpm of the rotor is recorded on the moving film by a combination electrical and optical system. The record is a series of dashes on the film, each dash and space representing twenty (20) revolutions of the rotor. (Film record of survey made in California well showing station recordings at various depths.) As the movement of the film is controlled by the clock the number of dashes and spaces in one minute of film travel represents the rpm of the rotor. The range of the instrument is from 0 to 2,500 rprn. The barrel or housing is 1-11/16 in. OD and seven feet long. Various types of expanding fluid traps are attached to the lower end of the instrument to direct the flow through the 1 in. orifice containing the rotor. The fluid trap for upward flow is shown in Figs. B and C. This assembly consists of eight arms with light spring

Jan 1, 1949

By C. R. Dale

The need for instruments to measure the movement of fluids and gas in wells has been recognized by engineers for many years. Information regarding flow in the producing interval has a direct bearing on completion practices in new wells and also provides information on the production characteristics of the well. Many hours of engineering time are spent in planning and completing wells but knowledge as to whether or not the original planning has produced the desired results has not always been complete. Many questions such as the following often arise: Why is it that two wells are completed under supposedly identical conditions, yet one well is a good one and the other is a poor one? Are the sands that look the best on the electric log contributing to the production? These and many other conditions in the producing well need to be under- stood in order to develop more efficient production practices and to improve on methods of completing new wells. It is the purpose of this paper to briefly describe one type of instrument, outline the methods of running the equipment and show the results of surveys made under various conditions. With an understanding of the use of this type of survey its importance can be evaluated in relation to the problems encountered by the operator. DESCRIPTION OF INSTRUMENT The instrument is a velocity recorder employing a clock-controlled 16mm film for recording the rpm of an extremely sensitive rotor which is rotated by the flow of fluids or gas in a well. The helical-vaned rotor and shaft, weighing one-half of one ounce are an integral unit exposed to the well fluids and are the only moving parts not enclosed in the fluid-tight housing. No packing or fluid seal of these parts is necessary and the shaft is mounted top and bottom on special jeweled bearings. Fig. A is the lower part of the instrument showing rotor and shaft with the protecting housing sleeve removed. The rpm of the rotor is recorded on the moving film by a combination electrical and optical system. The record is a series of dashes on the film, each dash and space representing twenty (20) revolutions of the rotor. (Film record of survey made in California well showing station recordings at various depths.) As the movement of the film is controlled by the clock the number of dashes and spaces in one minute of film travel represents the rpm of the rotor. The range of the instrument is from 0 to 2,500 rprn. The barrel or housing is 1-11/16 in. OD and seven feet long. Various types of expanding fluid traps are attached to the lower end of the instrument to direct the flow through the 1 in. orifice containing the rotor. The fluid trap for upward flow is shown in Figs. B and C. This assembly consists of eight arms with light spring

Jan 1, 1949

By Eugene S. Perry

The only outstanding development in Montana oil or gas fields during 1935 was the extension of the Cut Bank oil and gas field 7 miles southward. This field is now about 20 miles long and 3 to 8 miles wide, with 218 producing oil wells and 39 producing gas wells. Average daily production of the oil field during December, 1935, was about 6700 bbl.; total production for the year 1935 was approximately 2,020,770 barrels. The Cut Bank field in northern Montana is in a flat to rolling glaciated area used mainly for grazing purposes. Oil and gas occurs in sandstones and shaly sandstones in the Kootenai (Dakota) formation of Lower Cretaceous age at depths ranging from 2700 to 3000 ft. Prominent anticlinal or domal structure is not present, but small plunging anticlines occur locally. Strata dip westward from 75 to 200 ft. per mile. The field lies on the western flank of the Sweetgrass arch, a broad gentle upwarp over 150 miles long. Localization of oil and gas appears to be due either to pinching or lensing out of the sandstone beds, or else silting of the sandstones with clay minerals so that porosity becomes low. Within the field offset wells show marked variation in initial production, which suggests that differences in porosity of sandstone is the controlling factor. The gas-producing portion of the field is entirely updip (east) from the oil-producing portion, and the producing horizons are the same. Initial production of oil wells ranged from about 50 to about 200 bbl. per day, and initial open flow of gas wells ranged from about one million to about 37 million cubic feet per day, with an average of 11 million cubic feet. Initial gas pressures were slightly greater than 700 lb. per sq. in. Oil is brought to the surface by pumping. Both rotary and standard churn-drilling equipment are used. In the remaining 14 oil and gas fields but little new activity took place other than the drilling of offset wells and wells in proven territory. Continuation of "acid treatment" of wells in the Kevin and Pondera oil fields led to reconditioning of many old wells and the drilling of a number of new wells within these fields. Acid treatment of the oil-bearing horizon, which is the dolomitized and silicified Madison limestone of Mississippian age, has proved quite satisfactory, and some "bone dry"

Jan 1, 1936

By Eugene S. Perry

The only outstanding development in Montana oil or gas fields during 1935 was the extension of the Cut Bank oil and gas field 7 miles southward. This field is now about 20 miles long and 3 to 8 miles wide, with 218 producing oil wells and 39 producing gas wells. Average daily production of the oil field during December, 1935, was about 6700 bbl.; total production for the year 1935 was approximately 2,020,770 barrels. The Cut Bank field in northern Montana is in a flat to rolling glaciated area used mainly for grazing purposes. Oil and gas occurs in sandstones and shaly sandstones in the Kootenai (Dakota) formation of Lower Cretaceous age at depths ranging from 2700 to 3000 ft. Prominent anticlinal or domal structure is not present, but small plunging anticlines occur locally. Strata dip westward from 75 to 200 ft. per mile. The field lies on the western flank of the Sweetgrass arch, a broad gentle upwarp over 150 miles long. Localization of oil and gas appears to be due either to pinching or lensing out of the sandstone beds, or else silting of the sandstones with clay minerals so that porosity becomes low. Within the field offset wells show marked variation in initial production, which suggests that differences in porosity of sandstone is the controlling factor. The gas-producing portion of the field is entirely updip (east) from the oil-producing portion, and the producing horizons are the same. Initial production of oil wells ranged from about 50 to about 200 bbl. per day, and initial open flow of gas wells ranged from about one million to about 37 million cubic feet per day, with an average of 11 million cubic feet. Initial gas pressures were slightly greater than 700 lb. per sq. in. Oil is brought to the surface by pumping. Both rotary and standard churn-drilling equipment are used. In the remaining 14 oil and gas fields but little new activity took place other than the drilling of offset wells and wells in proven territory. Continuation of "acid treatment" of wells in the Kevin and Pondera oil fields led to reconditioning of many old wells and the drilling of a number of new wells within these fields. Acid treatment of the oil-bearing horizon, which is the dolomitized and silicified Madison limestone of Mississippian age, has proved quite satisfactory, and some "bone dry"

Jan 1, 1936

By L. K. Welch, C.W. Macgregor

The past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared with the longtime creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling, forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has been pointed out1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1943

By L. K. Welch, C. W. MacGregor

The past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared with the longtime creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling, forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has been pointed out1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1943

By Enid C. Plante, K. L. Sutherland

PRACTICAL metallurgists are unanimous in stating that oxidation of mined sulphide ore adversely affects separation of the constituent minerals under standard conditions in a mill. Frequently, the need for different operating conditions in different plants is attributed either to the extent of oxidation of the mineral surfaces or to soluble oxidation products. The investigations reported in this paper study the effect of oxidation on the primary condition necessary for flotation, namely that of adhesion of an air bubble to the mineral. OXIDATION PRODUCTS FROM SULPHIDE MINERALS Weinig and Carpenter1 state that the relative rates of oxidation of some sulphides are: FeAsS > FeS2 > CuFeS2 > ZnS >PbS > Cu2S tetrahedrite. They also show that oxidation is rapid at first, that sulphides of older geological formations are more stable than those of recent date and that mixtures oxidize more rapidly than any one mineral alone. The more rapid oxidation of mixtures is borne out by results of Gottschalk and Buehler2 who found that PbS, ZnS and CuS oxidized 8 to 20 times faster when pyrite was present. Only the end products of oxidation, sulphate and the metal ion, were identified in these tests. Gaudin3 states that pyrite is difficult to oxidize in the laboratory. Winchell,4 using pyrite containing 99.98 pct FeS2, allowed water to percolate through a bed of this ground material. At the end of three months only a trace of Fe +++and S04- were found. Even after 10 months the quantity of Fe+++ was only 7.8 mg and S04- 25.5 mg per liter of percolating solution. Carmichael5 confirmed Winchell's results on the slow oxidation of pyrite. Usually the oxidation of sulphide surfaces has been conducted in neutral or acid solutions, the acidity being caused by the oxidation products. Eliseev and Nagirnyak6 found that treatment of pure pyrite with lime gave only thiosulphate, but considered it possible that thiosulphate was obtained not by oxidation of the pyrite itself, but by oxidation of calcium disulphide. Mitrofanov7 suggested that thiosulphate was formed by the following process: oxidation of sulphide to give free sulphur (this frequently happens with marcasite), followed by oxidation of the sulphur to sulphur dioxide and reaction of the sulphur dioxide with sulphur to give thiosulphate. Ferric and ferrous hydroxides, or similar compounds, were shown to be present. The Research Staff of the United Verde Copper Co.8 treated ore from the United Verde mine with lime. Thiosulphate, sulphide and polysulphides were stated to be

Jan 1, 1947

By Enid C. Plante, K. L. Sutherland

Practical metallurgists are unanimous in stating that oxidation of mined sulphide ore adversely affects separation of the constituent minerals under standard conditions in a mill. Frequently, the need for different operating conditions in different plants is attributed either to the extent of oxidation of the mineral surfaces or to soluble oxidation products. The investigations reported in this paper study the effect of oxidation on the primary condition necessary for flotation, namely that of adhesion of an air bubble to the mineral. Oxidation Products from Sulphide Minerals Weinig and Carpenter1 state that the relative rates of oxidation of some sulphides are: FeAsS > FeS2 > CuFeS2 > ZnS > pbS > Cu2S tetrahedrite. They also show that oxidation is rapid at first, that sulphides of older geological formations are more stable than those of recent date and that mixtures oxidize more rapidly than any one mineral alone. The more rapid oxidation of mixtures is borne out by results of Gottschalk and Buehler2 who found that PbS, zns and cus oxidized 8 to 20 times faster when pyrite was present. Only the end products of oxidation, sulphate and the metal ion, were identified in these tests. Gaudin3 states that pyrite is difficult to oxidize in the laboratory. Winchell,4 using pyrite containing 99.98 pct FeS2, allowed water to percolate through a bed of this ground material. At the end of three months only a trace of Fe+++and So4- were found. Even after 10 months the quantity of Fe+++ was only 7.8 mg and SO4- 25.5 mg per liter of percolating solution. Car-michael5 confirmed Winchell's results on the slow oxidation of pyrite. Usually the oxidation of sulphide surfaces has been conducted in neutral or acid solutions, the acidity being caused by the oxidation products. Eliseev and Nagir-nyaka found that treatment of pure pyrite with lime gave only thiosulphate, but considered it possible that thiosulphate was obtained not by oxidation of the pyrite itself, but by oxidation of calcium disul-hide. Mitrofanov7 suggested that thiO~ulphate was formed by the following process: oxidation of sulphide to give free sulphur (this frequently happens with marcasite), followed by oxidation of the sulphur to sulphur dioxide and reaction of the sulphur dioxide with sulphur to give thiosulphate. Ferric and ferrous hydroxides, or similar compounds, were shown to be present. The Research Staff of the United Verde Copper Co.8 treated ore from the United verde mine with lime. Thiosulphate, sulphide and polysulphides were stated to be

Jan 1, 1949

By R. J. Stoehr, F. Howell

Since the ore mined in the Grants-Ambrosia Lake uranium area is taken from a water-saturated sandstone formation, part of the milling operation includes a drying process. The authors discuss the merits and disadvantages of two methods: natural drying and mechanical gas-fired drying; operating and cost data are included. In the Grants-Ambrosia Lake uranium area, approximately 7000 tons of ore are mined each day from a water-saturated sandstone formation. This ore is sampled and treated at four separate milling operations. Prior to the design and initial construction of the milling facilities, very little was known as to the physical properties of the ore which would be handled in the sampling and crushing facilities at the mills. All four mills initially were constructed without ore-drying facilities. As mining proceeded, it was determined that, even after drying the ore in place by use of drainage development underground, the moisture content of the ore as hoisted averaged approximately 18 pct. Actually, some of the mines produced ores which resembled cream-of-wheat in character and had a moisture content in excess of 24 pct. Each of the four mills had a differently designed sampling and crushing plant; therefore, the moisture content of the ores had varying adverse effects upon the operation of the plants. It was determined after some experience that most of the sampling and crushing facilities could not economically handle ore if the moisture content was greater than 10 pct—one operator considers 12 pct moisture as a maximum. In all of the plants, moisture content over 8 pct increases costs to some extent. In addition to the added sampling and crushing costs, some of the mills were located 15 to 20 miles from the mines and the high moisture content of the ores increased the haulage costs from the mine to the mill. It was generally conceded that it was necessary to employ some method to reduce the moisture content of the ore prior to sampling. Several methods were considered: 1) natural drying at the mine site, 2) mechanical gas-fired drying at the mill site, 3) mechanical gas-fired drying at the mine site, 4) radiant heating on concrete clabs, and 5) infrared shed drying. After preliminary investigation all possibilities but natural drying and mechanical gas-fired drying at the mill site were eliminated. NATURAL DRYING A cooperative feasibility study was conducted on the natural drying method. This study indicated the following: 1) During summer months May through September, ore piled 4-ft deep would dry from +20 to +10 pct HzO in 30 days with no mechanical turning. 2) In the first four days after piling a reduction of 5 to 7 pct total moisture content was accomplished by drainage and absorption of the water into the underlying ground on which the ore was piled, providing the ground surface absorption rates approached 10 gal per sq ft per day. After the first four days the decrease of moisture caused by drainage was practically nonexistent. 3) In the summer months drying by evaporation amounted to approximately 0.1 pct decrease in total moisture per day and mechanical turning of the ore could increase this as much as three times. 4) Climatic conditions of the area indicated that: a) Air temperatures averaged 64' May, June, July, August, September; 41" October, November, December, March, April; 31" January, February. b) Average rain fall was 10 in. with 40 pct of this occurring during July and August. c) Only on very rare occasions were there over five consecutive days with below freezing temperatures. d) The annual evaporation rate was approximately 75 in. On the basis of this study, two of the mill operations decided to attempt to meet the moisture specifications by natural drying supplemented by mechanical turning. The other two operations decided upon rotary gas-fired drying at the mill site. The natural drying method has been quite successful in practice. The ore running approximately 18 pct moisture is trucked from the head frame and piled in rows about 6 ft wide, 3 1/2 ft deep, 5 feet apart during the months of May through September. In approximately 30 days this ore will

Jan 1, 1961

By E. O. Wagner, V. F. Parry, J. B. Goodman

C. P. HEINER*—If you take out 35 pct of the total weight of the coal in the form of moisture, would that be about what it was in the case of North Dakota lignites ? V. F. PARRY (authors' reply)—That is about it. C. P. HEINER—That will be about a 35 pct loss and the final product will be about 11,000 Btu? V. F. PARRY—That is right. The heating value of the dried lignite is 10,000 to 11,000 Btu. C. P. HEINER—And the thought is not, then, to produce a commercial coal with that heavy loss, but to make other products—that is, synthetic fuel base, is that it? V. F. PARRY—The principal thought is to upgrade the coal, making it a more favorable raw material for industrial purposes, both for shipment and direct use. You see, the trouble in these lignites is that their moisture penalizes their

Jan 1, 1950

By Charles J. Potter

There are many sources of energy available for consumption. Some available are solar, tide and wind. However, in terms of relatively large usage, only four principal sources are used for primary energy today. They are coal, oil, natural gas and water power. Such additional items as wood and nuclear energy, although supplying quantities of energy today, do not in the aggregate amount to any real significant quantity, but nuclear energy must be considered for future use. In addition, such a thing as gas from distillation of coal and oil is not considered primary energy. The principal markets for primary energy are the electric power utilities, space heating, industrial uses and transportation. The electric utility use of energy is primarily from coal, followed by natural gas and water power. Space heating is primarily a gas market, followed by oil and then coal. Space heating by electricity is only considered in the generation of electric power. Transportation's principal source of energy is oil. Coal has practically no market left in this field.

Jan 4, 1962

By R. J. Colony

DEPOSITS of iron are widely scattered in the folded Cretaceous rocks and the associated igneous intrusives of Puerto Rico. Most of them are too small for commercial development, but a few have aroused some scientific and economic interest, among them the large body of residua] limonite at the west end of the island near Mayaguez1-6 (Fig. 1) and the mixed hematite and magnetite deposit on the southern slopes of the Sierra de Cayey, about four miles north of Arroyo.7-9 Neither of these orebodies has been developed, nor have investigations of the widely distributed deposits of magnetite, which include all the remaining occurrences of iron deserving of economic consideration, proceeded beyond the exploratory stage. With the possible exception of the mixed deposit near Arroyo, the magnetite is directly associated with andesitic and dioritic intrusives, which invade the Cretaceous rock section, and the bulk of it, occurring in calcareous sediments, is clearly of contact-replacement origin. The small deposit on Rio Portugues, north of Ponce, is found in a limestone band near its contact with an andesite dike.10,11 Two deposits of unde-

Jan 1, 1935

By Gerhard Derge

METALLURGISTS have used borax as a fluxing agent traditionally, but until recently elemental boron has played an insignificant role as an alloying element. Neither the metal nor its compounds have been regarded as important metallurgical materials and there is a surprising lack of knowledge concerning their metallurgical behavior. The new applications to steelmaking of both boron and borates, which arose in part from wartime incentives and restrictions, have been seriously handicapped by this lack of data. For example, rasorite, a naturally occurring sodium borate, has been shown to be an effective substitute for aluminum as a ladle deoxidizer in rimming steels.1 Likewise, the effectiveness of boron as an alloying agent has been demonstrated, 2,3 giving deep hardening when used in restricted amounts. The exploitation of both of these uses has been retarded by the difficulty of attaining suitable metallurgical control. Recognizing that the most important information required was a knowledge of the equilibrium between boron and oxygen dissolved in liquid iron, Gurry4 calculated this relation from the best thermal data available. However, estimates of the entropy of melting of boron, the activity coefficient of boron in liquid iron and the activity coefficient of B203 in slag were involved, and experimental work on this problem was obviously desirable. The experiments to be described were planned to establish the boron-oxygen relations in liquid iron and to demonstrate at the same time the ferroborate slag compositions in equilibrium with various amounts of oxygen in liquid iron. Accordingly, slags containing varying proportions of iron and boron oxides were held in contact with molten iron, and samples of both slag and metal were analyzed. The limitations upon the accuracy of the data will be considered, but in a practical sense the oxygen levels that can be attained in iron by iron borate slags, and the amounts of boron in iron at these oxygen levels were established. EXPERIMENTAL PROCEDURE No entirely suitable refractory was found for the mixtures of iron oxide and boron oxide used as slags. Crucibles of silica, magnesia, Ramix, beryllia, and zirconia were all tried unsuccessfully. The most satisfactory method discovered for handling them was the rotating-crucible technique, which creates a parabolic crucible of liquid iron 5,6 Even this was not entirely successful, for at steelmaking temperatures (1600°C.) the slags had such a low surface tension that they crept up to the refractory and slowly dissolved it. These difficulties made it impossible to maintain a constant slag composition for an unlimited period of time. However, by using the rotating

Jan 1, 1946

By T. Toda, R. Maddin

A study has been made of the microstructure and mechanical properties of splat-cooled aluminum-base gold alloys with gold concentration from 0.25 to 5.0 wt pct. These alloys have been quenched from the liquid state by a torsion-catapult technique, which has made it possible to pepare specimens suitable for mechanical property measwements. From the electron micrographs it has been shown that the solid solubility of gold in aluminum can be extended to 2.5 wt pct (0.35 at. pct) by splat-cooling, while the maximum equilibrium solubility is known to be less than 0.3 wt pct (0.04 at. pct). The very fine grain size (several tenths of a micron), the extended solid solubility, and the fine dispersion of a second phase (AuAl2) contribute concurrently to a substantial strengthening effect. In Al-5 wt pct Au splat-cooled specimens of less than 50 thickness, the yield strength is 17 kg per sq mm or 6 times as large as the strength of bulk specimens. For the Al-1.0 to 2.5 wt pct Au solid solution obtained by splat-cooling, the yield strength reaches 7.5 kg per sq mm after an aging treatment (for 10 hr at 200°C), while it is 3.7 kg per sq mm for the corresponding bulk specimens. A great deal of research has been done in recent years on the structure and the properties of metals and alloys rapidly quenched from the liquid state.' The term "splat-cool" has been used with the meaning of a rapid quenching from the liquid state., The splat-cooling techniques have produced large numbers of new structures, which are expressed in terms of metastable phases,3 concentrated solid solutions,4 amorphous phases,5'6 new phases,7 and so forth. Nearly all previous studies have concentrated on the physical properties; i.e., crystallography, structure, electrical resistivity, magnetism, and so forth, of the splat-cooled metals and alloys. The mechanical strength of splat-cooled metals and alloys has hardly been investigated except for some recent work by MOSS' on A1-V alloys. The principle common to all experimental techniques developed to obtain very rapid quenching rates is based on the heat transfer by conduction. Liquid must be in good thermal contact with a substrate of high heat conductivity. Both of the published devices known as the "gun" and the "piston and anvil" techniques suffer from certain shortcomings. For example, the specimen obtained by the gun technique is very small and flaky, and hence inadequate for mechanical properties measurements. On the other hand if the material is forced to yield a continuous speci- men by the piston and anvil technique, it is probable that some plastic deformation occurs during the quench. A novel method for rapid quenching of a liquid metal or alloy, the "torsion-catapult", has been devised by Roberge and Herman9 at the University of Pennsylvania. In the apparatus the melt is thrown out of a curved furnace by a catapult and impinges on a copper substrate. The apparatus has the advantage of producing a continuous foil which is relatively large in size and of a quality suitable for the measurements of mechanical properties. The quenching rate is estimated to be of the order of l05 to l06 ºC per sec, (comparable to rates achieved by the piston and anvil technique). In selecting an alloy to be studied we were made aware of the fact that gold was believed to be "insoluble" in in and consequently age hardening in the A1-Au system appeared to be interesting. Quite recently Heirnendahl13-15 revealed that the solid solubility, as determined by transmission electron microscopy, was 0.3 wt pct Au at 640°C and 0.25 wt pct Au at 600°C, decreasing with decreasing temperature. In an A1-0.2 pct Au alloy after quenching from a solution treating temperature of 600°C the yield stress was 2 kg per sq mm, and it increased up to 6 kg per sq mm after aging for 1 to 10 hr at 200°C. The precipitation occurred in the form of platelike particles mainly on (100) matrix planes. The intermediate phase n', the equilibrium phase n (AuAl2), and lattice relationships between both precipitates and the matrix were also investigated by electron microscopy. One of the purposes of the present research is to determine whether or not the solid solubility in this system, in which gold has a very small solubility in

Jan 1, 1970

By H. M. Faust

THERE are a number of different types of power plants. Some use coal to generate steam, others use oil or gas either in the form of steam or internal combustion equipment, while still others avail themselves of water power as a source of energy. A general comparison of the relative power production with different sources of energy in the United States, for several different years is set up in Table 1. This table shows that coal was used to generate 85.6 per cent of the total heat power requirements of 1909, and only 59.2 per cent of the 1930 requirements. The increasing proportion of modern heat energy generated by the use of fuel other than coal is apparent. If coal is to maintain its importance as a source of heat energy, the necessity for its improved perform-ance, in which preparation plays an -important part, cannot be stressed too strongly.

Jan 1, 1933

By M. C. Dow

Belt conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stone-crushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. General Reliability It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 /12 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. Loading the Belt It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined the to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1948

By M. C. Dow

Belt conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stone-crushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. General Reliability It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 /12 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. Loading the Belt It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined the to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1948

By K. J. Brondyke, P. D. Hess

Lack of correlation between densities of aluminum alloy samples solidified under reduced pressure (vacuum gas test) and hydrogen content of the metal is explained on the basis of inclusions serving as nuclei for hydrogen bubble formation. As a result of these findings, the vacuum gas test is suggested as a practical tool to indicate metal cleanliness and the potential effects of hydrogen. Visual obseroation of the sample during solidification under vacuum provides more useful information than that obtained either from density meas -urements or sectioning of the solidified sample. A rapid, practical method of detecting and measuring gas in molten-aluminum alloys has been sought for many years. The development of the vacuum gas test appeared to solve this problem. However, the vacuum gas test is subject to certain limitations, and the results must be interpreted mindful of these limitations, as described herein. Since the only gas which is appreciably soluble in aluminum is hydrogen, the terms gas and hydrogen will be used interchangeably in this paper. In the early days of the aluminum industry, when techniques were not as refined as they are today, it was customary to pour small "pancakes" of alumi- num on a metal plate. These were allowed to solidify under atmospheric pressure. Excessive gas in the metal was evidenced by the appearance of small bubbles on the surface of the "pancake".' It is obvious that such a method would only show very high gas levels far above any which could be tolerated by today's standards of quality required for most applications. Various attempts were made to develop methods which would be more sensitive. Among these were measurements of density of aluminum alloys solidified under controlled conditions, radiography of cast slabs, and examination of fractures. The method which showed the greatest promise and appeared most practical was the solidification of a sample of the molten aluminum alloy under vacuum. The samples so solidified are evaluated either by observation for bubble emission during solidification, by sectioning the solidified sample and examining for porosity, or by determining the density of the solidified sample. This test is known internationally as the Straube-Pfeiffer test or the reduced-pressure solidification test, but in America it is commonly referred to as the vacuum gas test2-' and will be so designated in this paper. The determination of density appeared an attractive and convenient means of providing a numerical rating for the samples. Attempts were made in some instances to correlate densities to hydrogen contents. Unfortunately, the visible loss of gas during solidification of samples with high gas contents precluded a correlation of vacuum gas test densities with the observed gas evolution. This led to Alcoa's use of two different pressures; 50 mm of

Jan 1, 1964

By M. C. Dow

INTRODUCTION BELT conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stonecrushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. GENERAL RELIABILITY It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 1/2 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. LOADING THE BELT It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined conveyor to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1947

By Oscar Lee

RESERVE Mining Co., owned jointly, by Armco Steel Corp. and Republic Steel Corp., controls 9% miles of magnetic taconite ore on the eastern end of the Mesabi Range lying between Mesaba and Birch Lake. The ore reserve which can be mined by open pit methods is conservatively estimated at 1.5 billion tons under a shallow, loose overburden requiring no rock stripping. Taconite now being mined is in the upper cherty horizon. It has been metamorphosed by the intrusion of gabbro and most of the iron oxide is altered to magnetite. The nonmagnetic portion of the iron is practically all in the form of silicate. The magnetic iron is finely disseminated through the rock and requires grinding -150 mesh for clean liberation of the iron oxide from the gangue.

Jan 5, 1954