Search Documents

By N. Mohan, A. K. Biswas, V. Y. Sampat Kumar

At low sodium-oleate concentration, calcite flotation is substantially improved by the use of CO2 instead of air. Electrophoretic mobility measurements indicate that carbonation results in the accumulation o f positive charge on the calcite particles. This heightens adsorption of oleate anion, an effect confirmed by tracer-technique measurements. Fundamental insight is obtained as to how CO2 serves better as an activator than some mineral and organic acids, how oxalic acid acts as a depressor, and why the influence of Ca++ ions, liberated during carbonation, on flotation behavior of calcite is insignificant and sometimes adverse.

Jan 1, 1972

By George Smith

ChillaQoe is situated in latitude 17" S., about 138 miles from the port of Cairns, with which it is now connected by rail. A township has been established on the banks of Chillagoe creek, a perennial stream of irregular volume crossing the field almost at rightrangles, nearly midway between the mining-camps of Calcifer and Mungana, which have been formed at the southeastern and western extremes of the field respectively. This situation was selected because of the water-supply and its proximity to the site most suitable for the erection of reductionworks. By its central position it commands the whole of the mines. The altitude above sea-level is about 1200 ft., whereas that of Calcifer and Mungana is 1400 ft.—a difference sufficient to account for a materially higher temperature at Chillagoe. The surrounding limestone bluffis add by radiation to the heat, and, at the same time, prevent the cool breezes from passing freely through the town; consequently, the temper* ture, which is high throughout the year, and especially so during the summer months, is here ge~ierally very oppressive also. The general trend of the field is southeast and northwest, and its length about 18 miles, with an average width of 5 miles; the approximate area is thus 90 sq. miles. The surrounding mineral-district is, however, much more extensive, and numerous other mines, sprcad over wide areas and producing a variety of minerals, exist in the same or parallel belts of mineralized country, of which Chillagoe proper covers but a very small portion. Immense bluffs of limestone, wollastonite and conglomerate, rising in places to nearly 300 ft., and so~netimes nearly a quarter-mile across, give the field a very picturesque and interesting appearance. The limestone has been classified as Devo-

Jan 1, 1904

By F. E. Bachman

Although it has been apparent to me for a long time that too great weight was currently given to the silicon-contents of foundry-iron, and that the theory of the control by silicon of the carbon-contents of cast-iron is unsound, or that, at best, the influence of silicon is too small to be of much practical value as a guide in foundry-work, it never seemed to me desirable to enter the lists against either the " silicon-fad " or the theory, for the reason that I had neither the time nor the facilities to prove my position, nor any better theory to offer. But since Mr. Summers has taken the step, it seems but right that I should give such facts as are at hand in support of his contention. At the same time I do not think these are enough to prove the case if the contrary proposition were not itself, as it seems to me, based on insufficient evidence. Both Keep's and Turner's conclusions seem to be drawn from irons carrying less than the normal amount of carbon; Turner's " base " being, moreover, a steel rather than a pig-iron, and both the white base and the ferro-silicon of Keep being so low in carbon that compounds of them would not give a material approaching the carbon-contents of a normal casting, and having, therefore, little value as showing the effects of silicon on foundry-irons, even if his samples were treated under the same conditions as those to which pig-metal is subjected in making castings.

Jan 1, 1899

By Francis Foley

FROM the point of view of the metallographist, the adaptation of x-rays to the study of the crystal structure of metals is of the greatest importance. While one may hardly consider the findings resulting from x-ray study as revolutionary, their positive nature, compared with the deductions we have been forced to accept from the work that had gone before, gives firmer ground on which to build and furnishes new fields for speculation. Prior to the advent of the crystallogram, the best work on the crystal structure of steel was that of Osmond and Cartaud.1 They concluded, from their investigation with percussion figures formed at various temperatures, that alpha, beta, and gamma irons belonged to the cubic system and that they showed well-marked specific characteristics and could not have the same internal structure. What the internal structures were, they had no direct method of determining; but from a consideration. of the fact that the 001 plane (that parallel to the cube face) is a plane of perfect cleavage and minimum hardness in alpha iron and that the 111 (octahedral) plane is by far the most important in the crystallography of gamma iron, they were led to suggest the simple cubic arrangement as that of alpha and the face-centered cubic arrangement as that of gamma iron. They suggested the body-centered cubic arrangement as that of beta iron. The atomic arrangement of the various crystal forms of iron has been quite definitely determined in recent years by means of x-rays and the work of Westgren2 and Westgren and Phragmèn3 has been rather conclusive. They not only determined the atomic arrangement of alpha, beta, and gamma iron but also that of the high-temperature modification delta.

Jan 10, 1925

By B. D. Cullity

INTRODUCTION THIS investigation of bismuth-selenium alloys was made in an attempt to find a suitable material for use in thermoelectric generators. These devices are simply thermocouple circuits designed for the efficient production of electrical energy from thermal energy, which may in turn be derived directly from solar radiation or from the combustion of fuels. The requirements of a material for use in a thermoelectric generator are obviously quite different from those of a material used in a temperature-measuring thermocouple. Naturally, for power generating purposes, the thermoelectric power (voltage produced per degree difference in temperature between the junctions) must be as high as possible. Furthermore, in order to obtain reasonably high power outputs, the materials used in the generator must have an electrical conductivity which is as high as possible. Finally, in order to minimize heat lost by conduction to the cold junction, the thermal conductivity must be as low as possible. The relation between these several factors and the efficiency of conversion of thermal into electrical energy-the thermoelectric efficiency-has been discussed by Telkes1 in a recent review of the subject. She gives the thermoelectric efficiency as: [ ] For many materials, some of the desired properties (for example, high electrical and low thermal conductivity) are almost mutually exclusive; the problem thus becomes one of finding a material which has the optimum combination of properties. BISMUTH-SELENIUM ALLOYS Work on the equilibrium diagram of the bismuth-selenium alloys has been reviewed by Hanson,2 who gives the diagram reproduced in Fig I. There are two intermediate phases in this system, BiSe and Bi2Se3. The existence of an alpha and beta modification of BiSe has not been demonstrated satisfactorily and the writer found no evidence of it in the present work. BiSe and Bi2Se3 have, like bismuth, a rhombohedral crystal

Jan 1, 1948

By William Campbell

In the olden days the making of alloys was an art, and the secrete of the craft were jealously guarded. To-day it has become a science, though the old ideas in regard to the secrets and formulæ are dying hard. Modern progress may be attributed to scientific research and testing of materials, and the substitution of chemical analytical control for " cook-book " methods. We know to-day a great deal about the constitution of alloys, the reasons of the change in structure and physical properties by heat and mechanical treatment; and this new knowledge is due for the most part to the physical chemist and metallographist, who have shown us that alloys are simply solutions, and as such obey definite laws. The application of the theories of solutions and of the phase rule tells us what ought to happen when our alloys are in a state of equilibrium. The working-out of the temperature-composition diagram (thermal diagram) for numerous alloys has thrown a light on the structure and constitution which has dispelled most of the darkness in which we labored before the advent of metallography. The work began with the determination of the freezing-point curves, and here the research of Le Chatelier,' Gautier,2 Roberts-Austen,3 and the other pioneers broke the ground. Next the physical chemists, Tammann,4 Rooseboom,5 Bancroft,6 and their colleagues, showed us the complete thermal diagram and its meaning. Then the researches of Heycock and Neville7 on the Cu-Sn series and of Shepherd 8 on the

Jan 1, 1913

By M. B. Bever, A. M. Reti, A. K. Jena

The results of this investigation show that in the system SnTe-PbTe l) the solid solutions have small exothermic heats of formation relative to the binary compounds, 2) solid-solution hardening is almost absent, 3) the tin and lead atoms are .randomly distributed on the sublattice occupied by them and do not undergo an ordering transition during a thermal treatment designed to promote such a transition, and 4) the lattice parameter changes linearly with composition. These findings suggest that the solid solutions of tin telluride and lead telluride approach ideal behavior. THE binary compounds SnTe and PbTe form a continuous series of solid solutions.' Information on several physical properties of these solid-solution alloys has been published.1"3 In the work reported here, the heats of formation, microhardness, and lattice parameters of these alloys have been measured and the possibility of an order-disorder transition has been investigated. Order-disorder transitions occur in some solid solutions of binary compounds. In the system Bi2Te3-BizSes, for example, the electropositive bismuth atoms and the electronegative tellurium and selenium atoms always occupy separate layers. In the disordered alloy Bi2Te2Se, the tellurium and selenium atoms are randomly distributed on the layers occupied by them, while in the ordered alloy they occupy distinct layers.4 The NaC1-type (Bl) structure of SnTe-PbTe alloys consists of two sublattices, one of which is occupied by the electropositive tin and lead atoms and the other by the electronegative tellurium atoms; any ordering would be expected to occur in the sublattice occupied by the tin and lead atoms. PREPARATION OF SPECIMENS Polycrystalline specimens of PbTe and Sn1-xPbxTe (x = 0.25, 0.50, and 0.75) were prepared by melting stoichiometric amounts of lead (99.999 pct), tin (99.98 pct), and tellurium (99.999 pct) in evacuated and sealed Vycor tubes. Because of the deviation of tin telluride from the stoichiometric composition5 this compound was prepared by melting 49.8 at. pct Sn and 50.2 pct Te. The tubes containing the melts were quenched into water; the solidified ingots were removed from the tubes and annealed for 2 weeks in vacuum (PbTe approximately 100°C below its melting point, the three alloys 100°C below their solidus tem-

Jan 1, 1969

By G. Ferrara

In process and plant simulation, more reliable prediction of industrial results and evaluation of data for designing purposes may be attained by the combined use of (a) modeling and simulation of ore characteristics and (b) modeling and simulation of integrated plant operations. The systems for modeling and simulation of ore characteristics are discussed as well as the conditions in which their use may be necessary (complex structure of the ore-body and variability of the ore fed to the plant). Two examples, for coal and bauxite run-of-mine (ROM), are reported. The procedure of linking the process unit models and the approaches for the solution of integrated systems are indicated. A general-purpose program for the simulation of integrated plant operations is described, and some examples of its use are reported.

Jan 1, 1984

By C. K. Leith

CERTAIN ideas on iron and steel sanctions to follow originated in a series of conferences held under the joint auspices of the War Department and Brookings Institute in Washington last spring. The views presented may be regarded as those of substantial segments of the steel industry. In view of the fact that steelmaking capacity can be so quickly converted to the production of armament, any effective control must necessarily include the entire steel industry and not solely the parts devoted to the production of implements of war. It must also be exercised all the way from production and shipment of raw materials through their ultimate conversion into finished products and use. Control will be dis- cussed under two main headings: (I) control of raw materials at the source; (2) control of steel capacity within the Axis countries.

Jan 1, 1944

By Francis Clark

WHEN 60:40 brass is heated to 825° C., given a drastic quench to obtain the beta solid solution, and reheated, various changes take place in the structure. Reheating at 200° C. causes a fine, granular, sorbitic structure to appear which has been considered alpha solid solution. These particles coalesce at higher temperatures of reheating, and at 470° C., the alpha forms twins. A further study of these transformations was considered worth investigating. EXPERIMENTAL WORK The object of the experimental work was to study the effect of mechanical work on rolled 60:40 brass, quenched and reheated, and the mechanism of twinning in the alpha reeds of a furnace-cooled specimen. It was desired to determine the effect of mechanical work on the transformations taking place on reheating the quenched material, both at 200 and at 470° C. A study of the nature of the structure resulting from the breakdown of the beta at 200° C. and a study of the mechanism of twinning above 470° C. were considered problems for investigation. The question of the twinning of the alpha reeds was also an important phase of the work. With high-power magnifications, there was hope of following these processes.

Jan 1, 1927

By David L. Holt

The contribution of grain boundary shear to total elongation, CS/E&apos;, has been measured in an Al-Zn eu-tectoid alloy that was quenched from above the invariant temperature, then annealed at 250° C to a grain size of&apos; 1.8 p. At 250°C, ks/E&apos; is low at both high and low strain rates, but reaches a maximum, estimated as 60 pct at an intermediate rate of 5 X 10 per rnin. Rate sensitivity, as measured by the index m = a log a/a log E&apos;, follows the same trend, and furthermore the maximum values of m and -cur at approximately the same strain rate. This result, combined with the metallographic observation that boundary migration enhances boundary shearing, is interpreted as supporting a previous suggestion that the high rate sensitivity characterizing super-plasticity is the result of combined boundary shearing and migration. It is suggested that the latter event relieves stress concentrations at triple points, and smoothes boundaries so that stress is governed largely by a viscous boundary shear. GrAIN boundary shear has been considered in relation to superplasticity in several recent papers.&apos; The problem has been to explain the high strain rate sensitivity of flow stress, and the variation of rate sensitivity with strain rate (E&apos;) and grain size (L). The requirements for superplasticity, small L and high T, suggest the reasonableness of an approach to high rate sensitivity involving grain boundary shear. Further support came from experiments on the A1-Cu eutectic alloy,&apos; where it was found that strain rate sensitivity of cast material annealed to produce an equiaxed, micron-size grain is always low; taking as an index of rate sensitivity m = a log a/a log <, m < 0.3. However, m in hot-worked alloy of comparable grain size can be as high as 0.7. In the cast and annealed material, each phase is a single crystal, the only boundaries are interphase boundaries, and it is, consequently, geometrically impossible for boundary shear to contribute to deformation in any major way. Other observations (for hot-worked material) were a-L at constant (low) strain rates and indications that the rate of recrystallization was enhanced as strain rate increased. As a result of this work, it was proposed that high rate sensitivity arises from a deformation mode of boundary shear associated with boundary migration. Migration serves to relieve stress concentrations at triple points, and smoothes boundaries so that they assume properties of fluid films. On the other hand, the low rate sensitivity observed at high and low strain rates reflects deformation of bulk material. Measurement of the variation of grain boundary shear with strain rate and m have not yet been made. Such measurements are important, especially in view of a proposal, differing in detail from the above, that high m arises merely from a transition between a grain boundary shear mode of deformation at low rates to a transgranular mode at high rates.2&apos;4 In the present work, the contribution of boundary shear to total deformation is measured and in addition metallographic observations are made on surfaces of deformed specimens to look at the interaction between boundary shear and migration. The Al-Zn eutectoid alloy was chosen for its homogeneous, fine-grained structure, which is obtained readily without hot-working. It has also been the subject of a previous phenom-enologically directed study. EXPERIMENTAL Material. Compression specimens, cross section 4 by + in., length \ in., were machined from a sand-cast ingot of composition 77.5 wt pct Zn, 22.5 wt pct Al. (The melt was prepared from 99.9 pct Zn and 99.99 pct Al.) After homogenization at 375°C for 50 hr, the specimens were quenched in brine and removed before the heat evolution that accompanies de -composition of the high-temperature phase.5&apos;6 The resulting microstructure, see Fig. l(a), was too fine for grain boundary sliding to be easily studied; coarser structures were obtained by annealing for various times at 2 50°C. Annealing was terminated by a brine quench. Final average intercept lengths between all grain boundaries (both interphase and those lying in a phase), L, were: 0.5 p [annealed for 15 min, Fig. (a)], 0.8, 1.1, and 1.8 p [Fig. l(b)l. Testing Procedure. An Instron machine was used for most of the compressive deformation. Tests were of two types: those in which crosshead velocity was changed in steps to measure m as a function of strain rate15 and tests at constant velocity to a fixed (engineering) strain of -0.2 (20 pct). Stress reached a steady-state value (a) which was plotted, on a logarithmic scale, against log strain rate (E&apos;). An alternate and equivalent evaluation of m was to take the slope of the log o vs log 6 curve. Time at temperature before testing was 15 min. Strain rates covered by the Instron (4 x lo-&apos; to 4 x 10&apos; per min) were insufficient; at a higher rate of 5 x lo2 per min a gas-operated testing machine was used, the gas driving a piston to compress the specimen at a controlled velocity.&apos; To obtain points on the log a vs log E&apos; curve at low rates, specimens were compressed by a dead weight. strain rate was an average value computed by dividing strain at the end of test by loading time. In some tests strain was measured at fractions of the loading time; creep rate was found to be reasonably constant.

Jan 1, 1969

By J. A. Jr. Church

I. EARLY FURNACES. . COPPER blast-furnace construction in America has long recognized a general standard in the rectangular water-jacketed shaft with separate forehearth. The details, however, and especially those relating to shaft dimensions, have had to meet a great variety of conditions, and show no uniformity whatever. Selecting a few of the present day Western plants, we find furnace lengths varying from 12.5 to 87 ft., widths at tuyere level from 42 to 84 in., and heights above tuyeres from 5 ft. 4 in. to 22 ft. 4 in. ; and comparing present designs with those of the past, we meet contrasts no less striking. Unlike its transverse section, the length of a furnace has come to depend rather on the size of unit desired than on the requirements of smelting ; and if the question of length be ignored, several of the various existing designs can be grouped together on the basis of a common transverse section. This section, having a width at tuyere level of 56 in. and a height above tuyeres of 18, ft., was developed at Great Falls, and the story of its development contains some interesting features. Ground was broken for the Great Falls works in the spring of 1891. About a year later, the concentrator was able to begin operation, followed within the next few months by the Brueckner, reverberatory, and converter departments, and in April, 1893, by the first blast fur-

Jan 7, 1913

By J. A. Jr. Church

I. EARLY FURNACES. COPPER blast-furnace construction in America has long recognized a general standard in the rectangular mater jacketed shaft with separate forehearth. The details, however, and especially those relating to shaft dimensions, have had to meet a great variety of conditions, and show no uniformity whatever. Selecting a few of the present day Western plants, we find furnace lengths varying from 12.5 to 87 ft., widths at tuyere level from 42 to 84 in., and heights above tuyeres from 5 ft. 4 in. to 22 ft. 4 in. ; and comparing present designs with those of the past, we meet contrasts no less striking. Unlike its transverse section, the length of a furnace has come to depend rather on the size of unit desired than on the requirements of smelting ; and if the question of length be ignored, several of the various existing designs can be grouped together on the basis of a common transverse section. This section, having a width at tuyere level of 56 in. and a height above tuyeres of 18 ft., was developed at Great Falls, and the story of its development contains some interesting features. Ground was broken for the Great Falls works in the spring of 1891. About a year later, the concentrator was able to begin operation, followed within the next few mouths by the Brueckner, reverberatory, and converter departments, and in April, 1893, by the first blast fur-

Jan 7, 1913

The United States Employment Office of the Department of Labor, of which the division of engineering and education, under the direction of A. H. Krom, maintains an office at 29 La Salle Street, Chicago, Ill., is engaged in a classification of engineers in order to make their services more readily available in case of need. We have received a form used by this division, on which it requires only a very little time to indicate one&apos;s particular line of work, his experience and the salary that he desires. We have been asked to impress upon members of the Institute the distinct advantages that come through registration. Filling out the blank entitles an engineer to free employment service, provides him with direct contact with the Government, supplies him with information in regard to engineering affairs, and helps him to become successful in his profession. The Government wishes every technical man to register, so that it may know the strength and location of the engineering reserve. It is therefore the duty of every patriotic engineer, whether he needs a position or not, to register at once. Blanks can be obtained by addressing the office above noted.

Jan 10, 1918

By A. R. Elsea, E. E. Fletcher

This paper describes a metallographic investigation of the influence of tungsten or molybdenum additions upon the transformation and precipitation reactions occurring in Co-rich Co-Cr alloys. It is shown that tungsten has little effect upon the a-ß transformation temperature range, while molybdenum tends to raise it. Both elements tend to promote the formation of ? phase, molybdenum being more potent in this respect than tungsten. HIGH temperature alloys, that is, alloys which have load-carrying ability at elevated temperatures, have been developed at an increasing rate during the past few years. This has resulted from the requirements in the design of modern aircraft engines. Although many alloys of this type are available, they have been developed on an empirical basis. Metallurgists do not have a clear understanding of the phases or structures that are responsible for these high temperature properties. In order to determine why these alloys possess this particular ability, a project was started at Battelle Memorial Institute with the object of learning more about the fundamental factors which promote high temperature strength in alloys. This study was to include a correlation of microstructure and the high temperature properties of Vitallium, an alloy which is widely used for high temperature service. Vitallium is a complex material both from the standpoint of composition and microstructure. Consequently, it was necessary to obtain informa- tion regarding the phase relationships in this alloy. The Co-Cr binary diagram was determined as the first phase of this investigation.&apos; A second paper described the effects of iron, nickel, or nitrogen on the reactions occurring in the Co-rich end of this system.&apos; The present paper covers a continuation of this investigation in which the effects of tungsten or molybdenum on the reactions occurring in Co-rich, Co-Cr-base alloys were determined. Preparation of &apos;rest Materials Two series of ternary Co-Cr-base alloys, representing Co-Cr ratios of 80:20 and 68:32 ( Cr x 100 =20 and 32 ) , were prepared containing ( Co + Cr = up to 6 pct W and up to 12 pct Mo. Melting stock consisted of electrolytic Co, electrolytic Cr, 99.9 pct pure W, and 99.9 pct pure Mo. Table I lists the chemical analyses of these materials. The melting furnace was a vertical porcelain tube

Jan 1, 1952

By K. M. Rolls, F. W. Reuter, J. Wulff

The superconducting behavior and microstructural characteristics of a nominal Nb-40 wt pct Ti-0.239 wt pct O alloy were studied as a function of ther mo -mechanical processing treatment. Critical current density us applied transverse magnetic field was obtained for 0.010-in.-diam wires at 4.2°Kin steady fields 14 to 110 kG. Both optical metallogvaphy and transmission electron microscopy were used to delineate the micros tructures of the same wires. It wan found that a 1-hr 500°C precipitation heat treatment after cold drawing to final size led to the highest critical current density. Heat treatment at 600°C also led to a high critical current density, but the precipitate differs in kind and form from that at 500°C. The resistire critical field was also found to be sensitive to precipitation heat treatment since the effective composition of the superconducting phase changes. This is discussed in terms of the oxygen in interstitial solid solution. Two types of high-field superconducting wire are at present used in the construction of high-field superconducting solenoids. These types are solid-solution alloy wire such as Nb-Zr and Nb-Ti and composites of the brittle inter metallic compound Nb3Sn. The latter generally have a high super cur rent-carry ing capacity which is difficult to vary if properly made. The supercur rent- carry ing capacity of the former can be varied drastically and often predictably by suitable thermomechanical processing treatments. In general, the critical current density Jc of the solid-solution type of alloy is increased by cold work and by additions of interstitial elements along with aging heat treatments. The imperfections which result are be-iieved to be responsible for the observed increase in Jc. In 1962 Kneip and coworkers1 found that the critical faurrent density of Nb-Zr alloys could be increased by proper heat treatment preceded and followed by cold work. Betterton and coworkers2 using a Nb-25 at. pct Zr alloy found that small additions of oxygen or carbon enhanced the effect of this heat treatment. They suggested that the interstitials present aided precipitation in the alloy, leading to a filamentary structure with superior properties. If the precipitation heat treatment was omitted, interstitial additions had a negligible effect on Jc. wong3 showed that higher heat-treatment temperatures lowered Jc. Walker and co-workers,4 who studied microstructure (by transmission electron microscopy) as well as superconductivity, found that the Jc anisotropy introduced by cold rolling was itself affected by heat treatment. They were unable to clarify the relation between microstructure and critical current density, although evidence of precipitation was indicated. More recent investigation of Nb-Zr alloys,5,6 besides showing that structural defects and fiber ing due to cold work and precipitation serve to raise Jc, also elucidate important optically observable microstructural changes which occur upon precipitation. In these reports, coarsening of the microstructural features was found to decrease Jc. Vetrano and Boom,7 who studied Ti-20.7 at. pct Nb, found that Jc was increased to a maximum by a 415°C, 3-hr heat treatment following quenching from 800°C and cold working. Heat treatments can also affect the resistive critical field Hr. Final-size heat treatments of Nb-Zr wire can lower Hr drastically if gross phase decomposition occurs5&apos;* or moderately if the effects of cold work are eliminated without changing significantly the composition of the phase of interest.3,5,6,8 The percentage of oxygen which can be added to Nb-Zr alloys to enhance Jc is limited by the difficulty of subsequent cold drawing. Since Nb-Ti and Ta-Ti alloys in contrast can tolerate appreciably higher percentages of oxygen, it was decided to investigate the superconducting behavior of various alloys in these systems. The present paper describes the results of adding oxygen to a nominal 40 wt pct Nb alloy as a function of thermomechanical treatment. I) EXPERIMENTAL PROCEDURE A small alloy ingot was prepared from high-purity niobium, iodide, crystal-bar titanium, and Nb2O5 powder by arc melting on a water-cooled copper hearth in a gettered argon atmosphere. The ingot was turned and remelted fourteen times to insure homogeneity. After final melting and rapid cooling, it was machined round to 0.415 in. diam, jacketed in stainless steel, and cold-swaged to 0.117 in. diam. The jacket was removed and swaging continued to 0.051 in. diam followed by wire drawing in carbide dies to 0.010 in. diam. Although it was intended that about 1500 ppm O (by weight) be added, inert gas fusion analysis indicated a 2390 ppm 0 content, apparently due to additional oxygen pickup in the arc furnace. Even so, the alloy was sufficiently ductile to be cold-worked to greater than 99.9 pct reduction

Jan 1, 1967

[ ] DISCUSSION F A LORIA*-The method of testing gun steel for resistance to surface cracking described in this paper was restricted to the examination of small, rod-shaped specimens The writer would like to point out the importance of other factors in producing defects in forged and bored gun tubes which would not be apparent in this investigation because of the nature of )he test Actual section size would accentuate the possibility of internal wall (bore) defects arising from unequal expansion between the internal and external wall surfaces on firing, resulting in internal tearing Checks and tears on the inside walls arise from internal tensions and nonuniformity on cooling, but the internal tearing can be reduced by using alloys of low expansion and of good thermal conductivity so as to reduce the difference between the outer and inner wall surfaces Also, the possibility of the location of inclusion segregates within a machined gun tube becomes more likely than in a small test specimen The effect of these nonmetallics on gun life and performance is evident when one realizes that the inclusions are soft yet brittle They reduce the amount of plastic deformation which can take place before cohesive failure occurs Once localized fracture has occurred at the position of a chain of these inclusions, a sharp notch (crack) is formed which produces stress conditions more favorable to cohesive failure than to plastic deformation These cracks aid erosion by providing channelways for the explosive gases, eventually leading to the tearing out or spalling of blocks of metal Oxidation of the surface may be partly responsible for the change in the surface of gun steel during firing observed by the author The appearance of burn on the surface is an indication that high temperatures were reached on firing, resulting in a slight oxidation of the surface Since the color of the oxidized film depends on both temperature and time, a higher temperature is required for a given color to form when it is caused by explosive heat, which acts for only an extremely short time at a given spot, than when it is caused by ordinary tempering The cross section of the gun steel specimen, Fig 16, illustrates that the repeated firing temperatures were high enough to cause

Jan 1, 1948

By William M. Shepard

The Tintic mining districts of central Utah com- prise one of the major silver-lead producing areas in the United States. Ore valued at nearly $450 million has been produced from these districts since the initial discoveries, in 1869, of veins cutting the Silver City monzonite stock. Subsequent production from the famous manto-type "ore runs", which characterize the Main Tintic district, was followed during the past 40 years by discovery of the blind orebodies of the East Tintic district, including the famous Tintic Standard mine and the most recent discovery, the Burgin mine, currently being brought to full production by Kennecott Copper. The occurrence of blind orebodies of exceptional size and grade in both the Main and East Tintic districts has made this area a field laboratory of major importance for the study of geochemical dispersion halos and alteration features associated with known ore, and has led to the discovery of additional concealed orebodies. The larger share of the basic data-gathering and interpretation has been done by members of the U.S. Geological Survey who have been studying the Tintic mining areas since before the turn of the century. These studies have been supplemented and expanded by the geological staffs of the local operating mining companies, by exploration geologists and by students.

Jan 4, 1966

By Monte J. Pool, Rudolph Speiser, George R. St. Pierre, William T. Ebihara

Standard free energies of formation of WO,, W O W20058 and WO3from oxygen and the lower oxide or tungsten have been determined in the tempel-ature range of 700° to 1220°C. A tentative W-O phase diagmm is presented based on the evidence that the oxide phases, "W18O49" and "W20058", are unstable at l~atm total pressure, below 585° and 485°C:, respectively. A HE need for a complete quantitative treatment of the phase equilibria of the W-O system has been establishedby metallurgists during the past few years. In an attempt to improve the endurance of tungsten exposed to oxidizing atmospheres at high temperatures, many research groups have studied the kinetics of tungsten oxidation. The reverse process, the reduction of the tungsten oxides to metal, has also been investigated to some extent. Regardless of the particular interest, metal to oxide or oxide to metal, a knowledge of the phase equilibria of the W-O system is required to properly interpret all of the kinetic observations. It should be possible to state the stable phases of the W-O system at any given values of the chemical potential of oxygen and the temperature.

Jan 1, 1962

Page Laboratory Methods...........................127 Special Analytical Methods.......................127 Improvements in the Accuracy of the Vacuum-fusion Method for the Determination of Oxygen in Steel....................127 Quantitative Spectrochemical Analysis of Mixtures of Gases.......131 Oxygen Samples from Open-hearth Bath...............133 Rapid Analysis of Sample for Alumina.................139 Accurate Carbon Analyses in Low-carbon Steel.............139 Laboratory Technique for Study of Reactions Involving Liquid Metal. . . . 142 Rotating Liquid Crucibles......................143 Stationary Crucibles.........................145 Jones and Laughlin Experimental Furnace...............148 Vacuum Melting..........................149 Measurement of Temperature of Liquid Iron and Steel;..........149 Pouring and Teeming Temperatures..................149 Bath Temperatures.........................151 Plant Methods.............................154 Methods of Studying Slags.......................154 Sampling Slag in the Open Hearth..................155 Viscosity of Open-hearth Slags....................155 Petrographic Examination of Slag...................156 Statistical Methods Applied to Study and Control of Chemical Relations in Bath...............................166 Rapid Method of -Correlation Applicable to Study of Steelmaking Reactions............................166 INTRODUCTION On Thursday morning, Feb. 16, 1939, a round table discussion was held on the subject of Experimental Methods in the Study of Steelmaking. Dr. John Chipman, Professor of Metallurgy at the Massachusetts Institute of Technology, and chairman of the A.I.M.E. Committee on Physical Chemistry of Steelmaking, presided. In opening the meeting, the chairman said: "The purpose of this round table is to discuss methods of study by which more and better information on the fundamentals of steelmaking can be obtained. It was thought that a round table discussion rather than a symposium would furnish the best opportunity for those actually using various methods of study to get together and discuss their common problems. For this reason attention will be focused upon methods of study rather than upon their results. We want new and current and up-to-date discussion.

Jan 1, 1940