Search Documents

By A. S. Richardson

The recent installation of a high-pressure propeller type fan at the Moose shaft of the Anaconda Copper Mining Co. at Butte, Mont,., is of interest on account of novelty of design and also because an appreciable saving was made over the cost of a reversible centrifugal fan such as is ordinarily used where a high pressure is required. The lower cost is due solely to the fact that by means of controls on the power supplied to the three-phase, alternating-current, induction motor, directly connected to the propeller it is possible to reverse the direction of rotation of the propeller and thus reverse the direction of air flow. The extra air ducts and reversing doors required for this purpose with centrifugal fans are not necessary, and their elimination greatly reduces these construction charges, which form a great part of the total expense. The Badger State mine for which the Moose shaft is used as the main outlet air course is now being developed to the 4100-ft. level. The old centrifugal fan, formerly used at the collar of the shaft, was installed 15 years ago at a time when most of the stoping was being done above the 2400-ft. level, and when the temperature of the rock was much lower than it is now on the bottom levels recently opened. The old fan, therefore, became inadequate to maintain desirable ventilation conditions, on account of the increase in resistance to air flow incident to the greater depth of the mine workings and because a much larger volume of air is required to offset the higher rock temperatures. Propeller, or disk, fans commonly used in the ventilation of mines are not suited to high-pressure work, but economies in the cost of their installation have long been recognized. In South Africa use has been made of a number of propellers placed in series along a common shaft, the number of propellers used being varied with requirements for meeting different conditions of mine resistance, but the mechanical efficiency is described as being low. In Butte, experimental work was done by the writer along similar lines under somewhat different conditions, but with poor results as to both pressure capacity and mechanical efficiency. Tests were also made of two different types of propeller fans of moderate size, which were said by the manufacturers to be suited to high-pressure mine ventilation.

Jan 1, 1932

By A. S. Richardson

THE recent installation of a high-pressure propeller type fan at the Moose shaft of the Anaconda Copper Mining Co. at Butte, Mont., is of interest on account of novelty of design and also because an appreciable saving was made over the cost of a reversible centrifugal fan such as is ordinarily used where a high pressure is required. The lower cost is due solely to the fact that by means of controls on the power supplied to the three-phase, alternating-current, induction motor, directly connected to the propeller it is possible to reverse the direction of rotation of the propeller and thus reverse the direction of air flow. The extra air ducts and reversing doors required for this purpose with centrifugal fans are not necessary, and their elimination greatly reduces these construction charges, which form a great part of the total expense. The Badger State mine for which the Moose shaft is used as the main outlet air course is now being developed to the 4100-ft. level. The old centrifugal fan, formerly used at the collar of the shaft, was installed 15 years ago at a time when most of the stoping was being done above the 2400-ft. level, and when the temperature of the rock was much lower than it is now on the bottom levels recently opened. The old fan, therefore, became inadequate to maintain desirable ventilation conditions, on account of the increase in resistance to air flow incident to the greater depth of the mine workings and because a much larger volume of air is required to offset the higher rock temperatures. Propeller, or disk, fans commonly used in the ventilation of mines are not suited to high-pressure work, but economies in the cost of their installation have long been recognized. In South Africa use has been made of a number of propellers placed in series along a common shaft, the number of propellers used being varied with requirements for meeting different conditions of mine resistance, but the mechanical efficiency is described as being low. In Butte, experimental work was done by the writer along similar lines under somewhat different conditions, but with poor results as to both pressure capacity and mechanical efficiency. Tests were also made of two different types of propeller fans of moderate size, which were said by the manufacturers to be suited to high-pressure mine ventilation.

Jan 1, 1932

By P. H. Mell

AMONG the minerals exhibited at the Atlanta Exhibition of 1881, soapstone, kaolin, and asbestos were well represented. The first two occur in large quantities, of very pure quality, throughout the South. The last is somewhat limited in amount, yet in certain localities it exists in masses sufficiently large to pay for working; in North Carolina, Georgia, and Alabama it has been mined with some profit. I would, in this paper, call special attention to the minerals soapstone and kaolin, because their many valuable qualities seem to have been al most entirely overlooked by our Southern manufacturers. Steatite, particularly, occurs in such large quantities, and generally in such close proximity to the great iron regions of Alabama and Georgia, that it is amazing that the iron companies will persist in sending abroad under. heavy expense for firebrick. It would require a much smaller sum of money to quarry this rock and place it at the various furnaces ; and the results obtained, I am sure, would prove its superiority over the majority of firebrick brought into this region. Soapstone, as well as kaolin, is found throughout the metamorphic regions of Alabama, Georgia, South Carolina, and North Carolina. Below-will be found seven analyses that I have made of this mineral, taken from various points in the four States above mentioned. I have also subjected these same specimens to severe fire-tests, and the results were very satisfactory. The tests were conducted in the following manner: Small portions of the compact variety were carefully weighed and placed in a Fletcher's new crucible furnace for gas, and subjected for half an hour to a heat that will in 12 minutes fuse iron. The only effect upon these specimens was a slight change in color .to a darker shade, a small loss in weight, due evidently to the evaporation of water, and, in one or two specimens, a slight degree of fusion on the sharp edges. The first specimen subjected to investigation was taken from a large outcropping in Tallapoosa County, Alabama. Specific gravity, 2.88 ; hardness, 1.9; color, blue gray. Composition Water, - 2.68 Silica, - 65.46 Iron oxide, - 2.10 Alumina, - 15.02 Magnesia, - 15.35 100.61

Jan 1, 1882

By Frank W. Reinmiller, Edward S. Hsia

Earth bottom thickeners are generally considered to be the lowest cost solution for thickener bottom construction presently available to the mining industry. In addition to the capital cost advantage, these basins have proven to be watertight structures providing trouble-free operation for indefinite periods of time. During the past 15 years, some 18 of these thickeners have entered service with no particular problems encountered in porphyry copper operations, counter-current decantation in a gold cyanide plant, and other similar applications in mineral processing. In the course of this work, technological advances have been realized in the procedures for engineering and construction of these units to assure watertight basins and achieve all possible economies in construction.

Jan 8, 1977

By S. S. Lisnyak, B. D. Lichter

An important question in the study of the "hot corrosion" phenomenon (i.e., accelerated oxidation of Ni-Cr-base and Co-Cr-base "superalloys" in the presence of sulfur) is the condition of formation and physico-chemical properties of different sulfides in the system Ni-Co-Cr-S. seyboltl has observed the presence of ((chromium-rich" sulfides of compositions M3S4, and M2S3 in the scales of superalloys after hot corrosion; however, as he points out, much confusion exists as to the identity of sulfides found on Ni-Cr and Co-Cr alloys. According to the literature,&apos; ternary sulfides, e.g., NiCr2S4, (monoclinic structure) and CoCr2S4 (spinel structure) exist in these systems. Therefore, it is likely that these compounds are found in the scale of alloys undergoing hot corrosion. At present this possibility has not been discussed in the literature. Accordingly, we have begun investigation on the properties of ternary sulfides and their mutual interaction. The magnetic and electrical properties of pure NiCr2S4 and pure CoCr2S2 have been previously determined."-&apos; In the present work we have studied the interaction between these sulfides at high temperatures by means of X-ray diffraction and magnetic susceptibility. The measurements were carried out at room temperature after appropriate thermai treatment of samples at high temperatures. For alloys containing the three elements nickel, chromium, and cobalt this interaction may be of importance in the study of the hot corrosion phenomenon. The compounds NiCr2S4 and CoCr2S4 were prepared from stoichiometric amounts of the elements and CoS in the case of CoCr2S4. Samples were mixed and sealed in evacuated silica tubes, slowly heated to 900&apos; to 100O°C, and held at temperature for a total of 120 hr (NiCr2S4) or 80 hr (CoCr2S4) with intermediate re-grinding~. X-ray diffraction showed a pure spinel structure for CoCr2S4 and a monoclinic structure for NiCr2S4. Samples of mixtures of the two ternary sulfides were prepared with different compositions, see Table I. Samples were heated for a total of 80 hr at 900&apos;C in evacuated silica tubes, with one intermediate regrind-ing. The capsules were slow-cooled to room temperature in the furnace. Samples for X-ray diffraction were prepared by placing powder on a glass slide with vaseline. Dif- fractometer traces were obtained on a G.E. XRD-5 diffractometer using a chromium tube and vanadium filter (40 kv and 31 ma). The size of the spinel unit cell was determined from the eight highest angle peaks (80 deg < 2b < 160 deg). Calculated lattice parameters were plotted vs cos B . ctn 0 and extrapolated to 6 = 90 deg. Measurements of the magnetic susceptibility were carried out at room temperature using the Faraday method in a magnetic field of 3000 G and using a Cahn RG automatic microbalance. The system was calibrated from the well-established susceptibilities of platinum and palladium: (Xpt = 0.968 x 10-6 g-1 and Xpd 7 5.04 x 10~6 g-1). The weight of samples were approximately 0.200 g. X-ray diffraction patterns for unsintered mixtures showed Bragg peaks from both the spinel (CoCr2S4) and monoclinic (NiCr2S4) structures. After sintering no monoclinic peaks were observed in samples containing up to 40 mol pct NiCr2S4. However, the spinel peaks were displaced to higher angles with increasing

Jan 1, 1970

By K. C. Lau

INTRODUCTION The design of engineering structures such as mine openings in and foundations on rock requires a knowledge of the constitutive laws governing the behaviour of discontinuous and layered rock masses. At the present time there are two main approaches for predicting the stress distributions and displacements in such engineering structures. In one method, the whole of the rock mass is discretized. The behaviour of the components of the rock mass, that is, the joints and the intact rock are modelled using analytical techniques such as the finite or boundary element methods. Typically the intact rock is modelled as a linear elastic material bounded by non-linear discontinuities. An alternative method of analysis is to describe the load-deformation properties of the jointed, layered or even reinforced rock mass in terms of smeared or equivalent homogeneous material properties. Such equivalent material properties may then be used to compute the stress distributions around openings and in foundations using standard methods of analysis such as the finite or boundary element techniques. Once the stresses have been obtained for the equivalent material, the stresses in the individual constituent layers or discontinuities may then be determined. Each approach to the problem has particular advantages. The first method is more likely to yield results which more closely represent the behaviour of the rock mass, since the behavioural responses of both the joints and intact rock are modelled. However, for many large or complicated geologic structures such an approach can become unweildy and uneconomical. In such cases, the equivalent

Jan 1, 1984

By Josef Westesson

No question in the metallurgical chemistry of the present day seems to be so difficult to agree upon as the determination of phosphorus in iron and steel. To my knowledge, there are at present at least three different methods in use in the iron laboratories of the United States, viz.: The citric acid method, the molybdate-magnesia method, and the direct molybdate method,—the last-named method having been lately adopted. Each of these methods has its advocates, who take every pains to prove its advantages, and the incorrectness of the others; and much has been written for the purpose of securing the use of a standard method—as yet, however, without any result. There is no doubt, or ought to be none, that each of these methods gives correct results, when it is carefully conducted and every precaution is taken. But it is not only correct results that we want nowa-days. The demand is great, also, for getting results in the shortest possible time. I think it has been sufficiently proved that the direct molybdate method, the weighing of the precipitate, answers well in both respects. Being a pupil of Prof. Eggertz, I have myself used his method for years until quite recently, as it is described by Mr. Troilius in our Transactions, vol. x., p. 166 (but with some slight modifications), and I can safely say that the results of this method agree well with those of the molybdate-magnesia method. I have, moreover, been checked, in a few instances, by some of the

Jan 1, 1885

By Y. H. Liu, R. Kiessling

The chromium, iron, and tungsten borides have been treated with ammonia at different temperatures. They are attacked, forming metal nitride and boron nitride, and the results are summarized in the tables. In the tungsten-nitrogen system a new phase has been observed, closely related to the known ß phase. THE present investigations were begun to determine whether any ternary phases exist in the transition metal-boron-nitrogen systems for the metals chromium, iron, and tungsten. Attempts to prepare such phases were made by using the borides of the metals as starting materials and ammonia as the nitriding agent. Although no new ternary phases have been found to exist, the results may be of some interest with regard to the technical use of the borides. General Procedure A steady stream of dry ammonia was passed through a silica reaction tube, the central part of which was kept at the reaction temperature while its ends were water-cooled. Weighed amounts of the borides were placed in a silica or porcelain boat and heated at different temperatures for a period of 10 to 24 hr. The boat was then rapidly removed from the reaction zone to the quenching zone, the water-cooled end of the tube, by means of a simple magnetic device. The nitrogen content of the products was determined by the increase in weight of the specimens, and the phase analysis was carried out by X-ray methods. For this analysis a Guinier-type camera, constructed at this Institute, was used with a bent, ground quartz crystal monochromator. The general reaction, which occurred in all the experiments, may be summarized as: metal boride + nitrogen -* boron nitride + metal nitride For the higher temperatures pure metal was formed instead of metal nitride. It is sometimes difficult to Discussi detect boron nitride among the reaction products by X-ray methods. Prolonged exposures of some specimens showed, however, that the strongest reflections of boron nitride were present. Additional evidence for its presence was given by the increase in weight of the specimens after nitriding. This increase was always greater than that corresponding to nitride formation only and was often in close agreement with the formula given above. Finally, a white powder, which was shown by X-ray methods to be boron nitride, was left if the reaction products after nitriding Fe,B at 448°C and FeB at 768°C were dissolved in diluted sulphuric acid. Ch rom iu m - Boron - N itrogen Five phases have been found to exist in the Cr-B system,&apos; , and all were used as starting materials. Investigations on the Cr-N system have shown the existence of two nitrides with ideal composition Cr,N and CrN.".&apos; * The results are summarized in Table I. All the borides are attacked and decomposed into chromium nitride and boron nitride, and the kind of nitride formed depends only on the temperature and not on the boride used as starting material. The lowest reaction temperature, however, is different for the different borides. Thus the 6 phase begins to react at about 735 "C, the r phase at about 800°, the S phase at about 900°, the 7, phase

Jan 1, 1952

By Brian F. Dyson

The surface tensions at 1550°C of some Fe-S alloys (in the range 0.008 to 0.052 wt pct S), Fe-Sn alloys (0.31 to 48.4 wt pct Sn), Fe-P alloys (0.038 to 2.38 wt pct P), Fe-Cu alloys (2.15 to 22.8 wt pct Cu), and Fe-1 pct C-S alloys (0.005 to 0.076 wt pct S) along with the surface tension of the base iron have been measured by the sessile-drop method. A mean value of 1754 dynes per cm was found for the surface tension of the base iron. Sulfur was found to be highly surface-active, the surface-tension results being in quantitative agreement with existing data. Tin and copper were found to be less surface-active than sulfur while phosphoms was completely nonsurface-active. The surface tensions of Fe-1 pct C-S alloys were found to be lower than those of the Fe-S alloys containing the same sulfur content. This was shown to be a mmzifestation of the increase in the thermodynamic activity of suZfur by carbon. It is only in recent years that attempts have been made to measure the surface tension of liquid iron of known high purity.1-3 Earlier measurements4-7 were made on liquid iron containing variable amounts of what are now known to be surface -active solutes. The exact value of the surface tension of liquid iron is still, however, open to some doubt. Halden and Kingery&apos; reported a value of 1720k 34 dynes per cm at 1570°C, Kozakevitch and Urbain8 gave 1790k 25 dynes per cm at 1550°C, while Van-Tszin-Tan et al. obtained a value of 1865k 37 dynes per cm at 1550°C. The first systematic investigation into the effect of controlled solute additions on the surface tension of iron was made by Halden and Kingery.&apos; They showed that sulfur and oxygen were highly surface-active, whereas nitrogen was only slightly active, and carbon inactive. A subsequent investigation by Kingery indicated that two other group-6B elements, selenium and tellurium, were also surface-active. This highly surface-active nature of sulfur and oxygen has recently been substantiated by Kozakevitch and Urbainla and Van-Tszin-Tan et al. l1 Kozakevitch and Urbainl2 have also conducted an experimental survey of the effects of a number of metals on the surface tension of liquid iron. Their surface-active nature was, in all cases, less than that of the group 6B elements. The present investigation was undertaken to study in more detail the surface tensions of dilute Fe-S alloys and to measure the surface tensions of binary alloys of iron containing phosphorus, copper, and tin. The effect of sulfur additions on the surface tension of Fe-1 pct C alloys was also determined. EXPERIMENTAL PROCEDURE The sessile-drop method was employed in the present investigation. An apparatus was built similar in principle to that described by Humenik and Kingery.lS It consisted of a horizontal silica tube, which could be evacuated to pressures less than 10-5 torr, with its central portion surrounded by a water jacket within which was a high-frequency coil. This generated heat in a tantalum susceptor placed inside the silica tube, which in turn radiated heat to the specimen mounted on a recrystallized alumina plaque. Temperatures were measured by an optical pyrometer and photographs of the molten drop were taken on a fixed-focus plate camera giving a magnification of X2. Surface-tension values were determined from the resultant drop using the method described by Baes and Kellogg.l4 The high vapor pressure of molten iron made it necessary to conduct all the experiments under a 1/4 atm of argon (greater than 99.995 pct purity). The analysis of the base iron used in the investigation is given in Table I. Each sample was approximately 3 g in weight and had a hemispherical base to ensure a uniform advancing contact angle on melting. The iron alloys were prepared individually in the sessile-drop apparatus by drilling a hole in the top of each sample and adding the required amount of solute, the drops being analyzed after the experiment. This method of preparation had the advantage of ensuring a consistent minimal contamination by oxygen due to refractory attack and also allowed surface tension to be measured at the same time. Every precaution was taken to ensure that the specimen was not contaminated by grease when it was introduced into the apparatus, the samples being cleaned in acid, dried in alcohol, and rinsed in petroleum ether. All handling was done with tweezers. Once the specimen had been placed inside the susceptor, the furnace was evacuated and the Sample leveled. The furnace was then degassed at approximately 1000"C before the argon was introduced. In every case the surface tension was determined at 1550" C.

Jan 1, 1963

CONTENTS PAGE DANIELS, SAMUEL, LYON, A. J., and JOHNSON,. J. B.-Casting and Heat Treatment of Some Aluminum Copper-magnesium Alloys 1 ELLIS, O. W. and SCHEMNITZ, D. A.-Experiments on the Heat Treatment of Alpha-beta Brass : 4 ENOS, GEORGE M. and ANDERSON, ROBERT J.-Coatings. Formed on Corroded Metals and Alloys 5 COMSTOCK, GEORGE F.-Notes on the Hardness of Heat-treated Aluminum Bronze 6 Casting and Heat Treatment of Some Aluminum Copper-magnesium Alloys Discussion of the paper of SAMUEL DANIELS, A. J. LYON, and J. B. JOHNSON, presented at the Milwaukee Meeting, October, 1924, and issued, as Paper No. 1350-N, with MINING AND METALLURGY, July, 1924. D. HANSON and M. L. V. GAYLER, Teddington, England (written discussion).-At the National Physical Laboratory, the writers have made a number of researches on the relation between the constitution and mechanical properties of aluminum alloys of various types; the results obtained were in good general agreement with those of the authors. The writers, however, did not think that increasing the copper content of sand-cast low-copper duralumin to 4 per cent. necessarily caused a drop in the elongation to 1.5 per cent., as stated on page 9. In the case of sand-cast copper-aluminium alloys they had obtained much greater elongation, in some cases as great as 13 per cent. in heat-treated castings. For example, in a sand casting containing 3.5 per cent. of copper, a strength of 12 tons per square inch and an elongation of 13 per cent. were obtained; in a casting containing 4.5 per cent. copper, a tensile strength of 13 tons, and an elongation of 9 per cent. were obtained. These values were the maximum; the elongation varied considerably, being as low as 5 per cent. in some cases. In the writers&apos; opinion, such variations are due more to unsoundness in the sand casting than to any other cause.

Jan 1, 1925

By Peter R. Morris, Alan J. Heckler

THREE angles are required to specify the orientation of a crystallite with respect to a physical reference frame. The distribution of crystallite orientations in a polycrystal is thus a function of three angular variables. The most widely used experimental techniques for studying orientation in polycrystals lead directly to the pole figure representation, i.e., the distribution of the poles of certain crystallographic planes in terms of two angular variables. In recent years1-5 methods have been developed which permit determination of the (three-angle) crystallite orientation distribution from several (two-angle) pole figure distributions. In this work Roe&apos;s method has been applied to the study of orientation in hcp materials. The method is illustrated for commercial purity titanium sheet (Ti-70) which was cold rolled (65 pct reduction), annealed at 1450°F for 3 min, and air cooled. The grain shape was observed to be equiaxed after this treatment. EFFECTS OF PHYSICAL, CRYSTALLOGRAPHIC SYMMETRY In Roe&apos;s method the crystallite orientation distribution, w(?,?,F), is expanded in a series of generalized spherical harmonics 11(?,?,F) = E E E W^Zirmtye-tote-in* [l] 1=o ,,,=-I ,,=-I where { = cos 8. The set of Euler angles employed here is illustrated in Fig. 1. The axis for each rotation is denoted by a double arrowhead. The positive sense of each rotation is that of a right-handed screw advancing in the direction of the double arrowhead. The X, Y, and Z directions correspond to the rolling direction, cross direction, and normal direction, respectively. In the initial orientation (10.O), (12.O), and (00 . 1) planes are perpendicular to the X, Y, and Z directions, respectively. The IC/ rotation about the Z axis is carried out first by rotating X into X&apos;, Y into Y&apos;, and leaving 2 unchanged, i.e., Z&apos; = Z. The 8 rotation about the Y&apos; axis is carried out second by rotating X&apos; into X", 2&apos; into Z", and leaving Y&apos; unchanged, i.e., Y" = Y&apos;. The I$ rotation about the Z" axis is carried out last by rotating X" into X"&apos;, Y into Y"&apos;, and leaving 2" unchanged, i.e., 2"&apos; = 2". Any specified orientation of the X&apos;", Y&apos;", and Z&apos;" crystal-fixed axis system relative to the X. Y, and Z physical axes (rolling direction, transverse direction, and sheet normal direction, respectively) can be obtained by appropriate IC/, 8, and (F rotations. The Zl,, of Eq. [l] are the Jacobi polynomials, augmented by the square root of the weight function. The Zl,, are symmetric in m,n, i.e., Zl,,= Zlnm. For orthotropic physical symmetry and hexagonal crystallographic symmetry, the coefficients, W!,,, of the series are all real, W!mn = Wzfi, = Wlm~ = Wlfi~, 1 and m are even and n is restricted to 6k, where k = ...,-2,-1, 0, 1, 2, .-.. The determination of the Wlmn from pole figure data has been previously described.&apos;~~ The Zl,, may be written in multiple angle form

Jan 1, 1970

By F. J. Norton

THE object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760° C. in a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove.

Jan 1, 1932

By J. Spotts McDowell

INTRODUCTION The magnitude of the thermal expansion of silica brick, and its inability to withstand rapid temperature changes, present problems of considerable importance in the manufacture of siliceous refractories. In the study represented by the experimental data herein described, these problems are considered from the point of view afforded by the results of recent investigators: Fenner and his associates of the "Geophysical Laboratory, Washington, D. C., who have established the stability relations of the silica minerals, and Endell and co-workers in Berlin, who have studied the changes brought about in the constitution of siliceous refractory materials upon the application of heat. In the process of manufacture, the quartzite from which the brick is made changes in part into cristobalite and tridymite. The attempt is herein made to determine by microscopic methods the degree of transformation in various specimens of test bricks manufactured at slightly varying temperatures of burning, with varying coarseness of grain, and to determine the effect of repeated burning. The effect of variations

Jan 10, 1916

By F. J. Norton

THE object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely, remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760° C. in a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and sub-sequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove..

Jan 1, 1932

By J. H. Frye, J. W. Caum

ONE of the most important methods of increasing the hardness of metals is alloying. In spite of the widespread use of alloys, the fundamental mechanism of alloy hardening is little understood. This is true even of the simplest form of alloy, the primary substitutional solid solution in which solute atoms substitute for solvent atoms at random in the crystal lattice of the latter. A fundamental understanding of the mechanism of solid-solution hardening would be important, both because of the widespread use of alloys of this type and because of the light that might be thrown on the mechanism of hardening in more complicated alloys. The present investigation covers the hardness of primary substitutional solid solutions of zinc, gallium,, germanium; and arsenic in copper. All of these are B subgroup elements from the third period of the periodic table. Cu, Zn, Ga, Ge, and As are in groups I, II, III, IV, and V, respectively and lie just to the right of the transition elements. Because of their cost, it is unlikely that Ga-Cu and Ge-Cu solutions will ever be of commercial importance, but the intent of this study has been to discover some of the fundamentals of solid-solution hardening and it has been demonstrated that such a study is far more likely to be fruitful if alloys are made up on the basis of position of the constituent elements in the periodic table than if commercially important alloys are used. Many investigations have. been made of the hardness of substitutional solid solutions, but lack of attention to purity of the metals, infrequent grain-size control, and the use of varying testing techniques have virtually invalidated any comparisons. The purpose of most investigations has been to solve immediate problems and not to solve the primary problem: Why do solid solutions usually have a greater hardness than pure metals? PREVIOUS WORK Theories have been advanced to account for the hardness of solid solutions,, but relatively little experimental work has been done. Perhaps the first experimental work of merit was that of Norbury1 on copper alloys. He showed that for several alloys there was a correspondence between the hardness of one atomic per cent solutions and atomic volume of the solutions. More recently Brick, Martin, and Angier2 have investigated the effect of various solute elements on the hardness of copper. They concluded that the hardening effect of these solutes depended "primarily on the difference in atomic volume of solute and solvent or, relatedly, upon the parameter, change of the solvent or the extent of solid solubility." They also observed the effect of these elements on hardness and texture developed by rolling and by annealing of rolled material. Austin3 examined the hardness and response to heat-treatment of various iron solid solutions. Frye and Hume-Rothery4 measured the hardness of a number of silver solid solutions containing approximately

Jan 1, 1943

By D. A. Kinneberg, J. W. Donaldson, N. J. Themelis

In the Kennecott Converter Smelting process (KCS), copper concentrate pellets are smelted and converted to high-grade matte in a modified Peirce-Smith converter using oxygen-enriched air and fuel. A high-grade matte bath is produced and maintained in the converter. Periodically, the slag layer is skimmed, slowly cooled, and its copper content is recovered by milling. Ladles of matte are transferred and finished to blister copper in another converter. The gases from the Kennecott Converter contain the SO2 products of the smelting and converting processes and can be treated in an acid plant, eliminating the problem of low-concentration gases associated with the operation of the reverberatory furnace. Pilot tests at Utah Copper Division were followed by a full-scale prototype converter test at the Chino Mines Division of Kennecott Copper Corporation. The concepts of the process and the results of this campaign are presented.

Jan 1, 1976

By Carl E. Johnson

INTRODUCTION A method for predicting water-flood oil recovery was reported by H. Dykstra and R. L. Parsons&apos; in 1950. It is now generally known as the Dykstra-Parsons method and is widely used by petroleum engineers. The method is semiempirical and consists of a correlation of four fundamental variables. These are: V, vertical permeability variation;&apos; a, mobility ratio; Sw initial water saturation; and R, fractional recovery of oil in place at a given producing water-oil ratio. The correlation extends over a wide range in each of these variables, and may be applied to all formations with initial oil saturations of 45 per cent or greater. The method of calculation originally outlined by Dyhtra and Parsons closely follows their derivation. And this is a convenient way of illustrating the development of some rather complicated ideas. However, in actual use it is more cumbersome than necessary. The purpose of this note, therefore, is to provide a simplified method for making Dykstra-Parsons predictions. A SIMPLIFIED GRAPHICAL SOLUTION The correlation between V, a, Sw and R, corresponding to a given producing water-oil ratio, can be shown on a single graph. This is best done by plotting V against a to show lines of constant R(1 - S, . WOR-0.2). Figs. 1, 2, 3, and 4 show these plots

Jan 1, 1957

By T. L. Fritzlen

EXTRUSION of aluminum alloys in this country is performed mainly by direct extrusion, therefore this paper is confined only to factors affecting the rate of extrusion by this method. Many factors affect the rate of extrusion of aluminum alloys. It is the purpose of this paper to present a discussion on the factors that are subject to technical control. Most of them are closely related, so that a clear-cut distinction between them is rather difficult. However, an attempt will be made to evaluate the effect of each factor separately, as far as possible. The most important factors only will be considered, and these will be discussed in detail under three general headings: (I) characteristics of the equipment, (2) size and structure of the ingot, and (3) temperature of ingot, cylinder, and other parts. It is a well established fact&apos; that the pressure and the speed of extrusion are related and are exponential functions of one another. Therefore, whenever a certain condition tends, for instance, to increase the pressure required for extrusion, it will reduce the extrusion speed if the pressure is maintained constant. For this reason, in this paper the effect of various conditions is expressed either in regard to their effect on the pressure required or the extrusion speed. Another established fact is the relationship between the temperature of the material being extruded and the pressure required to extrude. According to Schishokin,2 this relationship is of the exponential type, and as the temperature is increased the pressure required is decreased. It would seem from the preceding that the greatest rates of extrusion can be obtained by the use of higher temperatures. However, as is well known, other factors intervene to limit the rate of extrusion of aluminum alloys when increasing the temperature. These factors will be discussed in detail later. CHARACTERISTICS OF THE EQUIPMENT The capacity of the press determines the maximum unitary pressure that can be applied for any given cylinder diameter. Pressures used for extrusion of aluminum alloys range from approximately 50,000 lb. per sq. in. to 150,000 lb. per sq. in., dependent upon the alloy and the size of the shape extruded. Higher pressures could be used to advantage, but existing steels limit pressures employed in the production of extrusions. Numerous mechanical characteristics of the extrusion press affect extrusion rate. The most important characteristics of the press itself are: (I) sensitivity of the main pressure valve and accuracy of pressure gauges, (2) accuracy of equipment to heat the cylinder uniformly and to control cylinder temperature, and (3) accuracy of means of measuring the speed of extrusion. The variables subject to control during the extrusion operation are pressure, temperature, and speed, and it is evident that the preceding characteristics

Jan 1, 1945

By R. P. Smith

Iron-carbon alloys containing a single-phase austenite region and a two-phase azcstenite + cementite region at the desired temperature were prepared by partial carburization of iron or partial decarburization of carburized iron. Each sample was held at a fixed temperature until equilibrium was achieved. Analysis of the austenite for carbon then gave the solubility of cementite in austenite. Solubility measzcrements were made for the temperature range 734° to 1012°C. These values together with other data give 7560 cal for the mean heat of solution of cementite in austenite, and 0.765 pct C for the eutectoid composition of austenite. They also indicate that graphite is the stable phase at all temperatures between the eutectoid and eutectic temperature. Measurements of the solubility of cementite in austenite at 927oand 1011 "C, using a method based on the equilibration of iron with boro-cementites, are reported. The solubility of cementite in austenite (?-iron) has been computed by Darken and Gurry1 from the observed solubility of graphite in austenite, and the thermodynamic properties of pure iron and of iron-carbon alloys. They have shown that the solubility of cementite is greater than that of graphite in the temperature range between the eutectoid and eutectic, and thus that cementite is metastable with respect to graphite and austenite saturated therewith. Since their computation is not in accord with the earlier experimental work of Mehl and wells,&apos; the present direct determination of the solubility of cementite in austenite was undertaken. EXPERIMENTAL PROCEDURE Each iron rod about 1/2 in. O.D. by 4 in. was first carburized at a temperature and with a H2-CH4 gas mixture such that the carbon content would be greater than that corresponding to the solubility of cementite in austenite at the desired (lower) temperature; sufficient carburizing time was allowed that the carbon content became substantially uniform, as illustrated by Curve A, Fig. 1. The sample was then partially decarburized with a hydrogen-water vapor mixture, giving a carbon distribution as schematically illustrated by Curve B. The sample was then held in a helium atmosphere at the temperature at which the solubility was to be determined until the decarburized portion of the sample came to equilibrium with that containing cementite. Curve C of Fig. 1 represents schematically the final carbon distribution; the horizontal portion corresponds to the carbon content of austenite saturated with cementite. To bring the sample to room temperature without change in the carbon distribution and in machinable condition, it was first quenched in a salt pot at 480°C, then in water at room temperature. Successive layers were machined from the center 2 in. of the sample and analyzed for carbon by the usual

Jan 1, 1960

By E. Miller, J. M. Eldridge, K. L. Komarek

Aclivilies of magnesium in liquid Alg-Si alloys have been delermined between 5 and 60 at. pcl Si, close to the melling point of Mg2Si, by an improved isopieslic melhod. Silicon specinrens, held in alumina crucibles and graplrile conlainevs of special design, were healed in a letrlpevalure gvadient and equilibrated with mag-nesilcrrl rapor in a closed lilanium system. The ther-madynamic Junctions were calculated and compared with the thermodyuamic properties of the other three mg- Gvoup IVB systems. Lattice paramelers of three Mg2X compounds were measured. The bonding in the Mg2X compounds is largely covalent with small and uarying amounts of metallic and ionic conlvibutions. The Mg-Si phase diagram1 has one congruent melting compound, Mg2Si, of essentially stoichiometric composition, two eutectics, and very limited terminal solid solubilities. Little information is available on the thermodynamic properties of this system. The free energy of formation of Mg2Si has been determined by the Knudsen cell technique2 in the range 572" to 680oC, by the transportation method3 between 858" and 950oC, and by the electromotive-force method4 in the range 400o to 600°C. Kubaschewski and villa5 and caulfield6 have measured the heat of formation of Mg2Si. An electromotive-force study of magnesium-rich liquid alloys was recently published by Sryvalin el al.7 The present investigation was undertaken to complete a general survey of the thermodynamic properties of the homologous series of Mg-Group IVB systems, i.e., Mg-Pb,a9,Mg-Sn,10,11 mg-Ge,12and Mg-Si. An isopiestic technique, previously developed for similar measurements on liquid Mg-sn11 and Mg-Ge alloys,12 was modified for the Mg-Si system. Specimens of the nonvolatile component, silicon, were contained in dense alumina crucibles placed inside covered graphite crucibles which were heated in a temperature gradient in an evacuated and sealed titanium reaction tube and equilibrated with magnesium vapor of known vapor pressure. The alumina crucibles prevented contact between the highly corrosive liquid Mg-Si alloys and graphite. The graphite cruci- bles effectively preserved the high-temperature equilibrium composition of the liquid alloys containing highly volatile magnesium on termination of the experiments during the quench to room temperature. EXPERIMENTAL PROCEDURE Silicon of semiconductor-grade purity (E. I. du Pont de Nemours and Co., Brevard, N.C.) and 99.99+ pct Mg (Dominion Magnesium Ltd., Toronto, Canada) were used. Graphite crucibles with press-fitted lids were machined from high-density (1.92 g per cu cm) rods (Basic Carbon Corp., Sanborn, N.Y.) which had a maximum ash content of less than 0.04 pct. The alumina crucibles had a purity of 99.7+ pct (Triangle RR grade, Morganite, Inc., Long Island City, N.Y.). In preliminary runs the liquid alloys were contained in graphite crucibles following the exact procedure developed for the Mg-Ge system.&apos;2 These runs failed due to appreciable reaction between the molten Mg-Si alloys and graphite, and the results have been discarded. The procedure was then modified and the Mg-Si alloys were subsequently held in alumina crucibles. For most of the runs alumina crucibles of known weight and approximately 6.3 mm ID, 12.5 mm height, 1.0 mm wall thickness were loaded with weighed amounts of silicon and encapsuled in tightly covered weighed graphite crucibles 5/16 in. ID, 2 in. helght, 3/32 in. wall thickness). The graphite crucibles were machined from rods which were 85 pct of the theoretical density. These crucibles were therefore sufficiently porous so as to permit magnesium vapor to effuse through the silicon under the experimental conditions of approximately 970O to 1220°C and 1 day equilibration time. However, negligible magnesium was lost from the crucible during the quench due to the slow effusion rate through the pores of the graphite. The inner alumina crucible prevented the liquid alloys from contacting the graphite, and the very tightly fitting graphite crucible lids served to retain any magnesium vaporizing from the alloys inside the crucibles during the quenching step.12 The loaded silicon-alumina-graphite cells were positioned, one above another, on a 16-in.-long titanium thermocouple well and tied securely to the titanium tube with thin molybdenum wires held in grooves around the circumference of the graphite crucibles. A thin (0.005-in.) molybdenum strip prevented contact between the graphite crucibles and the titanium. This assembly was lowered into a titanium reaction tube (la in. ID, 16 in. long, $ in. wall thickness) closed on one end which contained a 11/2-in.-long cylinder of magnesium at the bottom. The inner titanium thermocouple well was positioned eccentrically in the large tube because of the eccentric mounting of the cells on the well. Appropriate modifications of the titanium cap"&apos;12 were made to join the inner and outer titanium

Jan 1, 1968