Search Documents

By A. S. Richardson

THE recent installation of a high-pressure propeller type fan at the Moose shaft of the Anaconda Copper Mining Co. at Butte, Mont., is of interest on account of novelty of design and also because an appreciable saving was made over the cost of a reversible centrifugal fan such as is ordinarily used where a high pressure is required. The lower cost is due solely to the fact that by means of controls on the power supplied to the three-phase, alternating-current, induction motor, directly connected to the propeller it is possible to reverse the direction of rotation of the propeller and thus reverse the direction of air flow. The extra air ducts and reversing doors required for this purpose with centrifugal fans are not necessary, and their elimination greatly reduces these construction charges, which form a great part of the total expense. The Badger State mine for which the Moose shaft is used as the main outlet air course is now being developed to the 4100-ft. level. The old centrifugal fan, formerly used at the collar of the shaft, was installed 15 years ago at a time when most of the stoping was being done above the 2400-ft. level, and when the temperature of the rock was much lower than it is now on the bottom levels recently opened. The old fan, therefore, became inadequate to maintain desirable ventilation conditions, on account of the increase in resistance to air flow incident to the greater depth of the mine workings and because a much larger volume of air is required to offset the higher rock temperatures. Propeller, or disk, fans commonly used in the ventilation of mines are not suited to high-pressure work, but economies in the cost of their installation have long been recognized. In South Africa use has been made of a number of propellers placed in series along a common shaft, the number of propellers used being varied with requirements for meeting different conditions of mine resistance, but the mechanical efficiency is described as being low. In Butte, experimental work was done by the writer along similar lines under somewhat different conditions, but with poor results as to both pressure capacity and mechanical efficiency. Tests were also made of two different types of propeller fans of moderate size, which were said by the manufacturers to be suited to high-pressure mine ventilation.

Jan 1, 1932

By Frank W. Reinmiller, Edward S. Hsia

Earth bottom thickeners are generally considered to be the lowest cost solution for thickener bottom construction presently available to the mining industry. In addition to the capital cost advantage, these basins have proven to be watertight structures providing trouble-free operation for indefinite periods of time. During the past 15 years, some 18 of these thickeners have entered service with no particular problems encountered in porphyry copper operations, counter-current decantation in a gold cyanide plant, and other similar applications in mineral processing. In the course of this work, technological advances have been realized in the procedures for engineering and construction of these units to assure watertight basins and achieve all possible economies in construction.

Jan 8, 1977

By William R. Webster

An investigation has been made of 500 samples of universal and sheared plates of basic Bessemer and basic open-hearth steel manufactured by the Pottstown Iron Company, the carbon-limits being 0.07 to 0.18 per cent. Through the courtesy of Mr. W. H. Morris, President, I am able to lag before the Institute the results of these tests. The samples tested were all taken from the finished material, and the chemical determinations were made on drillings from the broken test-pieces, which were sent to the chemist without giving him the heat-numbers. The results are such as to encourage me to keep on with the work, and, if possible, to have it carried out on other steels. It is kith this view that I now offer my tables in their incomplete form. My first table mas constructed by grouping the tests according to chemical analysis in various. ways, and making a rough tabulated statement, from which the ultimate strengths were worked out and carefully compared with the actual results of the tension-tests. From data thus obtained, one table after another was worked out, and by this method of "cutting and trying" I finally arrived at the results which I now present in Table I. (p. 771). I do not claim absolute accuracy, but my approximations have proved to be so close that the figures are practical data for current use at the works. The indications are that a pure iron, without carbon, phosphorus, manganese, or silicon, if it could be obtained, would give 38,000 pounds ultimate strength. This is assumed as a base, and to it is added the effect of each of the above elements, as explained below. The upper part of Table I. gives the ultimate strength due to carbon and phosphorus, and is the same for both basic Bessemer and basic open-hearth steels. The lower part gives the increase in ultimate strength due to manganese. By adding this to the amount obtained from the upper part, we have the ultimate strength of basic Bessemer

Jan 1, 1893

By J. Spotts McDowell

INTRODUCTION The magnitude of the thermal expansion of silica brick, and its inability to withstand rapid temperature changes, present problems of considerable importance in the manufacture of siliceous refractories. In the study represented by the experimental data herein described, these problems are considered from the point of view afforded by the results of recent investigators: Fenner and his associates of the "Geophysical Laboratory, Washington, D. C., who have established the stability relations of the silica minerals, and Endell and co-workers in Berlin, who have studied the changes brought about in the constitution of siliceous refractory materials upon the application of heat. In the process of manufacture, the quartzite from which the brick is made changes in part into cristobalite and tridymite. The attempt is herein made to determine by microscopic methods the degree of transformation in various specimens of test bricks manufactured at slightly varying temperatures of burning, with varying coarseness of grain, and to determine the effect of repeated burning. The effect of variations

Jan 10, 1916

By William Hutton Blauvelt

Coke is the product of dry distillation of bituminous coal, by which the volatile matter is driven off, producing a hard body of cellular structure. Not all bituminous coals will coke, and there has been much discussion regarding the substance which is present in coking-coals to distinguish them from dry coals. Professor Lewes says that the bituminous matter in coal is largely derived from the spores of fossil mosses. Resins are present in all soft coals, and contribute largely to the cementing of the coke. The resinates and hydrocarbons begin to distil out at moderate temperatures and leave the pitchy residual, which at 500' C. forms a mass already well caked together, if the proportion of humus residual is not too great. This coke is soft, but if the heat be raised to 1,000° C. the pitch decomposes further, leaving carbon, and Professor Lewes is convinced that the coking bond is due to these liquid products which distil off, leaving pitch, which then carbonizes and binds the mass into coke. Professor Parr concludes that the structures of the organic compouilds of the coal Which furnish the cemeding-material for coke, and which are apparently attacked by oxygen, have not been determined and seen] to vary somesvhat in different types of coal. However, they yield, on oxidation, humic acids of varying composition which decompose into powdery residues. Because of the complex nature of these substances and the difficulty experienced in isolating and identifying them, the theory of coking is still an open problem and the explanations advanced are largely hypothetical. In the coking process the volatile matter driven off in the oven consists mainly of tar, ammonia, and gas, familiarly known as by-products. Both the quality and quantity of coke and by-products vary greatly With the composition of the coal.

Jan 1, 1913

By M. A. Cook

Sutherland used an ion-pair adsorption model to derive the author's hy-drolytic pee-acid) adsorption equation for the contact bubble curves of Wark and Cox. To do so it was necessary to postulate that the sum of coverages of surface anion sites by the collector and depressant anions is practically unity. It is here shown that the free energy of Sutherland's postulated collector ion (x-)-depressant ion (OH-) exchange reaction (for no other than the OH- to compete with X-), namely EX + (OH-) Z SOH- + X-, is in some cases positive and X- should not even adsorb. Also, in many cases the (OH-) adsorption must be quite negligible even though the collector covers only about a sixth of the mineral surface at the threshold of air bubble contact. This, however, contradicts the postulate that permits one to derive the correct bubble contact eqwztion for the ion-pair model. Furthermore, the requirement for charge neutrality leads in the ion-pair model to the (impossible) constancy of the ratio @+)/(OH-) along a contact bubble curve in which pH may change by more than seven units. HYDROLYTIC ADSORPTION EQUATION Hydrolytic (free-acid or free-base) and ion-pair (H', X-, or R', OH-) adsorption models of the collector in metal sulfide and similar flotation systems are superficially alike and somewhat difficult to differentiate. This is because they yield, under seemingly valid assumptions, equivalent forms of the equations describing the distribution of the collector between the aqueous solution and the mineral surface. This has been discussed by the author and associates1-4 and more recently by Sutherland,' both for simple collector-mineral and for more complicated collector-depressant-mineral systems. In the hydrolytic adsorption model the equations describing the contact bubble curves of Wark and coxeJ7 are as follows :2 Here X is the collector anion, D- the depressant anion, 9, and On are the fractions of the free-acid sites S on the surface of the mineral covered by collector and depressant free acids, respectively, and @ is the fraction of uncovered sites. Kx is the free-acid collector dissociation equilibrium con- stant, K1 that for the free-acid collector adsorption, KD that for the free-acid depressant dissociation, and K2 the equilibrium constant for the free-acid depressant adsorption. Eqs. 1 to 5 yield upon simultaneous solution the result is the critical free-acid concentration for bubble contact in the absence of depressant-free acid. Eq. 8 expresses the conditions along a simple collector-mineral contact bubble curve for the case HD = 0, or V = 0. Last and Cook showed that Eq. 6 applies generally and with good accuracy in the collector-depressant-metal sulfide mineral systems. Inci-dentally, it has been shown by infrared absorption studies that in some cases the free-acid adsorption process splits out water.' In this case, Eq. 2 might be written SHOH + HX Z SHX + H20, with a similar equation replacing Eq. 4 for depressant-free acid-water exchange. This possibility does not change, however, the basic equations or considerations of the hydrolytic adsorption model. Indeed, this type of free acid-water exchange reaction was predicted for fluorite and iron ore flotation by oleic acid in the dry grinding and boiling processes.410

Jan 1, 1961

By William E. Ford, Edward Salisbury Dana

430. The more important of the special properties of a mineral species with respect to heat include the following: Fusibility; conductivity and expansion, especially in their relation to crystalline structure; change in optical characters with change of temperature; specific heat; also diathermancy, or the power of transmitting heat radiation. The full discussion of these and other related subjects lies outside of the range of the present text-book. A few brief remarks are made upon them, and beyond these reference must be made to text-books on Physics ant1 to special memoirs, some of which are mentioned in the literature (p. 305).

Jan 1, 1922

By P. S. Kotval, H. Hahell

PRECIPITATION of M23C6 carbides at grain boundaries in austenitic steels and nickel base superalloys has received considerable attention. Hatwell and Berghezan,1 in a study using carbon extraction replicas, observed that dendritic growth of the M23C6 carbide phase occurred at grain boundaries in austenitic steels. Merrick and Nicholson2 have observed that in thin foils of "Nimonic 75" alloy the precipitation of M23C6 carbide was discontinuous at grain boundaries. Lewis and Hattersley3 have suggested that the type of M23C6 precipitation observed in Ni-Cr austenites represented the early stages of discontinuous precipitation. In a more recent study, Singhal and Martin4 have concluded that grain boundary M23C6 precipitation involves the migration of an austenite grain boundary by a mechanism very similar to that proposed by Tu and Turnbull.5 Tu and Turnbull's suggestion essentially involves grain boundary migration under the driving force arising from the difference between the surface free energies of the opposite sides of the plate. Thus, Singhal and Martin's observation4 implies that the first stage of discontinuous precipitation has taken place and that the grain boundary has provided a diffusion short circuit for the sub-stitutional solute atoms (principally chromium) which assist the preferential growth of the M23C6 plate in contact with the grain boundary. However, no evidence of the characteristic cellular morphology typical of discontinuous precipitation was found in Singhal and Martin's studies. Presumably, this is due to the low volume fraction (i.e., low supersaturation of solute) of the precipitating carbide reported by Singhal and Martin.4 Recently, Raymond6 has studied precipitation of the M23C6 carbide in Incoloy alloy 825 and shown that the growth of this phase is perpendicular to grain boundaries at 1400°F and in the plane of the grain boundary at 1700°F. The former aging condition resulting in discontinuous or "cellular" precipitation. Raymond has suggested an explanation for this behavior based on the relative rates of chromium diffusion by volume and grain boundary diffusion at the two different aging temperatures. In the course of a recent investigation on precipitation behavior in several ' strengthened superalloys, precipitation of M23C6 carbide at grain boundaries was studied. Under conditions of a high degree of supersaturation, the M23C6 carbide precipitates in the discontinuous or cellular morphology in Waspalloy (Ni-18.51 Cr-2.0 Fe-3.53 Mo-1.16 Al-2.78 Ti-0.09 C). This note presents electron microscopy observations of this mode of precipitation and its effect on mechanical properties. Specimens of Waspalloy after "solution" heat treatment at 1950°F show essentially single phase matrix with a few residual particles of "primary" MC carbide. In normal commercial heat treatments, precipitation of Ni3(Al,Ti) ordered fcc r' phase occurs throughout the matrix and M23C6 precipitates as globular particles at the grain boundaries. In these commercial heat treatments the degree of supersaturation during precipitation is low. However, if specimens of Waspalloy are quenched from the solution heat treatment temperature of 1950°F and then aged at an aging temperature where the degree of supersaturation is high, discontinuous precipitation of M23C6 occurs. Figs. 1 and 2 show thin foil micrographs of Waspalloy, solution heat treated at 1950°F, water quenched, and aged at 1292° and 1598°F, respectively, for 500 Fig. 1—Thin foil of Waspalloy, solution heat treated at 1950°F for 1 hr, water quenched, and aged for 500 hr at 1292°F. Magnification 15,500 times. Fig. 2—Thin foil of Waspalloy, solution heat treated at 1950°F for 1 hr, water quenched, and aged for 114 hr at 1598° F. Magnification 13,000 times.

Jan 1, 1970

By Carl E. Johnson

INTRODUCTION A method for predicting water-flood oil recovery was reported by H. Dykstra and R. L. Parsons' in 1950. It is now generally known as the Dykstra-Parsons method and is widely used by petroleum engineers. The method is semiempirical and consists of a correlation of four fundamental variables. These are: V, vertical permeability variation;' a, mobility ratio; Sw initial water saturation; and R, fractional recovery of oil in place at a given producing water-oil ratio. The correlation extends over a wide range in each of these variables, and may be applied to all formations with initial oil saturations of 45 per cent or greater. The method of calculation originally outlined by Dyhtra and Parsons closely follows their derivation. And this is a convenient way of illustrating the development of some rather complicated ideas. However, in actual use it is more cumbersome than necessary. The purpose of this note, therefore, is to provide a simplified method for making Dykstra-Parsons predictions. A SIMPLIFIED GRAPHICAL SOLUTION The correlation between V, a, Sw and R, corresponding to a given producing water-oil ratio, can be shown on a single graph. This is best done by plotting V against a to show lines of constant R(1 - S, . WOR-0.2). Figs. 1, 2, 3, and 4 show these plots

Jan 1, 1957

By W. A. Anderson

Recrystallization of cold-worked metals has long been known to proceed by a process of nucleation and growth.' When a cold-worked metal is heated to a temperature at which recrystallization will ensue, nuclei of new grains, essentially strain-free, appear and grow. As the process proceeds, nuclei continue to appear and to grow, until the cold-worked matrix has been entirely consumed and recrystallization has been completed (Fig. I). Conducted isothermally, a measurement of the fraction of the matrix recrystallized plotted against time, yields an isothermal recrystallization curve, showing the time course of the recrystallization process (Fig. 2).2 Evidently, then, the rate of recrystallization is determined by the rate at which nuclei form and the rate at which they grow. The rate of nucleation N is the number of nuclei that form in unit time in unit volume of the unrecrystallized matrix, and the rate of growth G is the increase in radius of the recrystallized grain per unit time. In recent years attempts have been made to determine N and G as these vary with the well-recognized variables affecting recrystallization: time, temperature, degree of deformation, etc.1 Such studies yield information that is more fundamental than that conveyed by the conventional recrystallization diagram,' since the rate of recrvstallization is thus analyzed into its two component rates3 Methods are now available by which N and G can be measured, and analytical expressions have been developed for the interrelationships among N, G, the isothermal recrystallization curve, and the final grain size, which greatly facilitate analysis.2-4 The application of these methods has been demonstrated recently for the recrystallization of silicon ferrite.2 Data on N and G in dependence upon the recognized recrystallization variables are, however, very fragmentary;" values of N and G have been determined for some metals, but the effect of temperature, which would yield the fundamentally important activation energies, has been too little studied. Thus far there has been no detailed study of the recrystallization of any one metal in terms of X and G ovcr appreciable ranges of the variables time, temperature, degree of deformation, and original grain size. It is the purpose of the present paper to provide such a study, employing aluminum.

Jan 1, 1945

By R. B. Gavert, David J. Mack

ROOM- and elevated-temperature compression tests were made on the binary 3/2 electron compounds AuZn, CuAu, AgZn, AgMg, AuCd, and NiA1. These compounds possess either the B2 CsC1-type ordered structure or the A2 bee disordered structure represented commonly as ß and ß on equilibrium phase diagrams. In testing at room temperature, cylindrical specimens 0.508 cm by 0.330 cm diam were seated directly on an instron compression load cell (CF 0 to 10,000 lb). At elevated temperatures, testing included a special apparatus with a furnace heat source and a protective atmosphere.' The specimens were strained at a rate of 1 pet per min. The compounds were prepared from 99.99 pet or better high-purity elements. Vacuum and/or argon cover gas was used throughout the mixing, melting, and specimen drawing processes. The generally equi-axed specimen grains varied in size from 0.5 to 1.5 mm for the five different compounds. The stress-strain curves in compression showed

Jan 1, 1968

By Cyril Stanley Smith

BeTa brass (consisting of approximately equal atomic proportions of copper and zinc) exists as a random solid solution at high temperatures, hut at low temperature< an ordered structure is stable, with the copper and zinc atoms occupying alternate sites on the body-centered-cubic lattice. On cooling, ordering commences at a temperature of 450° to 470°C., depending on the composition. The degree of ordering progressively increases at lower temperatures until it becomes virtually complete at about 100°C. The electrical resistivity of the alloy illustrates the changes clearly (Fig. I). This type of reaction has been a favored subject for study by physicists. An excellent summary of the theory is to be found in a paper by F. C. Nix and W. Shock1ey.l All published data on electrical conductivity, specific heat and other properties agree in indicating that the ordering reaction in beta brass takes place so rapidly that it cannot be prevented or even retarded by quenching&apos; With most ordered alloys, cold-working induces disorder and

Jan 1, 1943

By Cyril Stanley Smith

BeTa brass (consisting of approximately equal atomic proportions of copper and zinc) exists as a random solid solution at high temperatures, hut at low temperature< an ordered structure is stable, with the copper and zinc atoms occupying alternate sites on the body-centered-cubic lattice. On cooling, ordering commences at a temperature of 450° to 470°C., depending on the composition. The degree of ordering progressively increases at lower temperatures until it becomes virtually complete at about 100°C. The electrical resistivity of the alloy illustrates the changes clearly (Fig. I). This type of reaction has been a favored subject for study by physicists. An excellent summary of the theory is to be found in a paper by F. C. Nix and W. Shock1ey.l All published data on electrical conductivity, specific heat and other properties agree in indicating that the ordering reaction in beta brass takes place so rapidly that it cannot be prevented or even retarded by quenching&apos; With most ordered alloys, cold-working induces disorder and

Jan 1, 1943

By J. Szekely, V. Stanek

Heat and gas flow interactions in nonisothermal packed beds were examined in the paper. A study was made of the response of the system to a step or pulse change in the inlet gas temperature, with a fixed value of the overall pressure drop across the bed. Under these conditions the heat flow and fluid flow transients are coupled because the convective heat transfer rate is alfected by the mass flow rate of the gas which, in turn, for a fixed pressure drop will depend on the temperature profile in the system. The Problem was stated in terms of differential equations, which were integrated numerically. The parameters used in the computation were so chosen to reflect the operation of the stack region of blast furnaces and sinterbeds. The computed results showed that the pressure drop-flou1 relationships and the rate of progress of the temperature fronts (waves) were strongly interrelated and were also markedly affected by variations in particle size and in void fraction. MANY metallurgical processes involve the contact of solid particles with a gas stream in a packed bed arrangement under nonisothermal conditions. Examples are shaft furnaces, regenerators, pebble heaters, and the sinter process. Although the heat and mass transfer aspects of packed bed processing have been extensively studied, the associated flow phenomena and in particular the effects of nonisothermality on the flow, have received little attention to date. :In fact, most of the previous workers considered the flow rate of the carrier gas time invariant and independent of the heat or mass transfer processSzekely and carr2 have shown that the pressure drop-flow relationships in nonisothermal packed beds may be strongly affected by the temperature profile within the system. These authors have devised a method for relating the pressure drop to flow for a given temperature profile. thus providing an extension of the Ergun equation to steady nonisothermal systems. Finally, in a recent paper willmot3 examined the response of regenerators to externally imposed changes in the gas flow rate. Both these investigations were somewhat specialized since, in general, neither the temperature distribution nor the gas flow rate may be regarded as truly independent variables, thus the heat transfer and the fluid flow problems have to be solved simultaneously. The work reported here is divided into two parts: in Part 1 the general formulation is given and a detailed discussion is presented of fixed bed systems. Part is devoted to systems in which a gas and particulate solids are contacted in a counter flow arrangement. FORMULATION Consider a nonisothermal fixed packed bed, extending from through which a gas is flowing. The problem is to develop a relationship between pressure drop and gas flow (with the gas flow being the dependent variable) and to evaluate the rate at which a change in the gas temperature, imposed at the inlet, travels through the system. Let us consider an infinitesimal section of the bed and establish differential heat, mass, and mechanical energy balances over this region. In addition, relationships are needed describing the temperature dependence of gas density (equation of state) and the temperature dependence of viscosity. These may be written as: where c, and are constants. It is noted that in this formulation we neglected any temperature gradients within the solid particles, thus assuming these to be either sufficiently small or of sufficiently high thermal conductivity to meet this condition. The justification and consequences of this assumption will be mentioned in the discussion.

Jan 1, 1970

By James A. Barr

Prospecting methods used in Tennessee have gradually improved with the years, as required by depletion of the easily accessible and shallow deposits and the universal trend toward mechanization, and as necessitated by exploring deeper beds, often occurring under limestone and flinty overburden. In the early days it was a very simple matter to dig pits by hand, using a plentiful supply of local farm labor to expose relatively shallow deposits of "brown rock" under shallow clayey overburden that would stand up without timbering. Visual inspection of the exposed phosphate and expert judgment of the "grade" analysis, aided by a "biting" test to reveal presence of unwanted silica, furnished most of the information required. All this might be helped by a few samples sent to the local chemist† who supplemented his income by judicious trading or tanning a few bear skins. The extra curricula activities did not affect the accuracy of the analysis which hold up even under present day standards. Some shot and core drilling was done in Hickman County, mostly for the limestone-like blue Phosphate deposits. The next step was the use of a 4-in. posthole auger, hand operated as described by Guenther, followed by a completely mechanized rig, as described by Pickard. Both these methods are practically adapted to the prospecting of the relatively soft brown rock deposits at moderate depths of clay overburden. For prospecting in areas of deeper overburden, such as are often found in Hickman County, up to 150 or even 200-ft depths, a modified core-drilling method is described by Guenther. Johnston describes a special diamond-drilling technique, developed by TVA, to penetrate flint horizons, which was adopted by the International Minerals in chemical corporation to prospect in Hickman County where deposits had previously been prospected at considerable expense and with difficulty, by small, temporary, hand-dug shafts.

Jan 1, 1948

By James A. Barr

Prospecting methods used in Tennessee have gradually improved with the years, as required by depletion of the easily accessible and shallow deposits and the universal trend toward mechanization, and as necessitated by exploring deeper beds, often occurring under limestone and flinty overburden. In the early days it was a very simple matter to dig pits by hand, using a plentiful supply of local farm labor to expose relatively shallow deposits of "brown rock" under shallow clayey overburden that would stand up without timbering. Visual inspection of the exposed phosphate and expert judgment of the "grade" analysis, aided by a "biting" test to reveal presence of unwanted silica, furnished most of the information required. All this might be helped by a few samples sent to the local chemist† who supplemented his income by judicious trading or tanning a few bear skins. The extra curricula activities did not affect the accuracy of the analysis which hold up even under present day standards. Some shot and core drilling was done in Hickman County, mostly for the limestone-like blue Phosphate deposits. The next step was the use of a 4-in. posthole auger, hand operated as described by Guenther, followed by a completely mechanized rig, as described by Pickard. Both these methods are practically adapted to the prospecting of the relatively soft brown rock deposits at moderate depths of clay overburden. For prospecting in areas of deeper overburden, such as are often found in Hickman County, up to 150 or even 200-ft depths, a modified core-drilling method is described by Guenther. Johnston describes a special diamond-drilling technique, developed by TVA, to penetrate flint horizons, which was adopted by the International Minerals in chemical corporation to prospect in Hickman County where deposits had previously been prospected at considerable expense and with difficulty, by small, temporary, hand-dug shafts.

Jan 1, 1948

By Stanley Gill

The apparatus is composed of sections of small diameter, seamless steel tubing welded into a continuous flexible tube. At the bottom end a 1/4-in. pipe nipple with a 10 to 15-lb. weight is attached, together with a registering thermometer and a pair of ball check valves. The entire length of tubing is coiled in a single layer upon a drum 4 ft. in diameter which can be attached to the platform of a truck and provided with devices for winding and unwinding the tubing. Connections are made with the upper end of the tubing through a stuffing box, thence to a gas manifold to which a pressure gage is connected. Hydrogen gas is carried in standard 2-ft. cylinders and readings are taken by admitting gas into the tubing from one (or both) of the hydrogen cylinders until the pressure has been built up above that to be measured. At this time the gas supply is cut off. Excess gas escapes through the open end of the tubing and when equilibrium is reached, the pressure is read at the surface gage. Corrections are made for the weight of the column of gas. The advantages claimed for the apparatus include accuracy and the ability to measure the pressures at any number of points without removing the gage. Among the disadvantages of the apparatus are the somewhat bulky size of the equipment and its relatively high initial cost.

Jan 1, 1933

By Ulick Evans

I SHOULD like to commence by saying how much I appreciate the honor which the American Institute of Mining and Metallurgical Engineers has done me in inviting me to visit your country, and to deliver this lecture before you. In choosing a subject, and in deciding what to include and what to omit, I have endeavored to discuss as far as possible work carried out recently in Europe with which you may not be unduly familiar. It would be poor return for your hospitality, and a mistaken sort of compliment indeed, if I were to load the lecture with accounts of researches carried out in your own country-researches with which you are probably better acquainted than I. Not that I have in any way excluded work done on this side of the Atlantic from my survey; one would indeed find it difficult to write on this, or on any other branch of science, without mentioning American work. But I have endeavored as far as possible to concentrate on aspects of the case which will, I hope, be comparatively fresh to you, and I feel fairly certain that this will be in accordance with your own wishes. If a strip of iron is heated strongly at one end, the other end remaining cold, there is produced over the heated portion a layer of oxide scale, the thickness of which diminishes steadily with the distance from the hot end. Somewhere in the middle of the strip, the thickness of the oxidized layer will become comparable to the wave length of light, and over this region the thin films give rise to a series of beautiful interference tints, commonly known as "temper colors." The colors are caused by the fact that two trains of light waves are reflected respectively from the outer and inner surfaces of the oxide film, and the possibility arises that the "crests" of one series of waves may coincide with the "troughs" of the other, thus diminishing the intensity of the light of some particular wave length. The state of affairs in this part of the strip is shown diagrammatically in Fig. 1, in which the film thickness is enormously exaggerated, of course, in comparison with the length of the strip; the

Jan 1, 1929

By Frederick N. Rhines, Robert F. Mehl

IT has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick&apos;s law (equation 1 below), ‡ in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick&apos;s law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Zedele and of Zedele.§ These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a singles olid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By J. Kent Smith

VANADIUM is generally spoken of as a rare element; but, even in the light of our resources as known a couple of years ago, this description could be accepted in a qualified sense only. In fact, vanadium is very widely distributed, being a constituent of most clays, while even caustic soda has been shown to contain almost regularly a minute proportion of it, although the quantity in each case is so small as to render impracticable the extraction of the metal there from with profit. The opening-up of a large deposit of vanadium sulphide ore in South America has put a new phase on the commercial outlook of vanadium, the technical value of which for the improvement of steel has been proved by rigorous scientific investigation.

Sep 1, 1907