Search Documents

By Ross C. Anderson, William I. Weisman

THE manufacture of anhydrous sodium sulphate or salt cake from natural deposits in the United States has been in general somewhat of a marginal undertaking. Competition from foreign sources and from large quantities of byproduct sodium sulphate produced domestically in the manufacture of hydrochloric acid and other chemicals has existed and continues. For example, most of the sodium sulphate produced is a byproduct or co-product in the manufacture of hydrochloric acid through the reaction of sodium chloride with sulphuric acid. In recent years, many manufacturers of rayon have installed equipment to recover sodium sulphate from waste spin bath liquors; today this is an important source. Before World War II large quantities of sodium sulphate were imported from Germany. In 1949 imported material from Europe again appeared on the domestic market. Natural sodium sulphate from Canada in substantial quantities also enters the United States markets. Despite this kind of competition, numerous attempts have been made to exploit various natural deposits of sodium sulphate in this country, but only a very few of these have survived economically over a period of years. One of these few operations is the plant of the Ozark-Mahoning Co. located 13 miles south of Monahans in West Texas. Several factors contributing to the successful life of this plant may be summarized as follows: 1—Geographical location. Monahans is reasonably close, freightwise, to the Kraft paper mills in Texas, Arkansas, and Louisiana; the Kraft paper industry is the greatest consumer of sodium sulphate in the United States. 2—Availability of natural gas as low cost fuel. Proximity of the natural gas fields of West Texas has been a tremendous asset, as the availability of low-cost natural gas is to all industry throughout the Southwest. 3—The nature of the deposit. The occurrence of sodium sulphate brines in southeastern New Mexico and West Texas has been very well described by Lang,' who writes that the brines are found in the Castile formation of the Delaware basin. Here weathering has altered the anhydrite so that a relatively porous gypsiferous zone overlies a dense impervious mass of anhydrite. This porous zone provides traps where percolating ground waters that have picked up soluble salts may lodge. These traps or pockets are the natural brine reservoirs exploited at Monahans. Although several hundred wells have been drilled, currently some 25 wells serve to supply brine to the plant. All are within 1 1/2 miles of the plant and are conveniently tied together by an electric power system serving electric motors driving the pumps. Having the raw material in the form of a brine which can be pumped from shallow wells makes possible much simpler and more efficient handling than if it were in form of solids. By contrast, other deposits of sodium sulphate, such as those in Arizona, Nevada, and North Dakota, are in the form of the solid minerals, thenardite and mirabilite, which present somewhat more of a mining and mineral dressing problem.' The largest producer of sodium sulphate from natural sources in the United States is at Searles Lake, Cal., and there a brine also is utilized. 4—Water. Substantial quantities are needed for cooling towers and for operation of gas engines. An area underlain with brine is not a promising source of fresh water, but fortunately, after a long search, an adequate supply was found nearly two miles from the plant. It may be appropriate to discuss briefly the grades of sodium sulphate offered on the market. Salt cake is the name usually applied to the grade of sodium sulphate used by the Kraft paper industry. It may be a low analysis byproduct, 95 to 97 pct sodium sulphate, with as much as l 1/2 to 2 pct residual acid, or it may be a natural product. Usually salt cake is considered a low grade product, but a great deal of a higher grade of material is marketed under this name. The specifications for glassmakers' salt cake are somewhat higher than those of the paper industry, usually requiring 98 pct sodium sulphate. Technical anhydrous sodium sulphate is a high grade material and usually exceeds 99 pct sodium sulphate. It finds the biggest market in the textile industry and is used as a builder in some synthetic detergents. Glauber's salt, Na2SO4. 10H20, is usually of high purity. Preferred for some uses, it normally has been recrystallized from an anhydrous salt. A unique manufacturing process has been developed at Monahans. This process results in the production of an exceptionally high grade of salt cake, and qualifies for nearly all uses, including many which specify the technical anhydrous grade. All of the finished product, which is very white, passes a 10-mesh U. S. Standard screen, and is retained on a 200-mesh U. S. Standard screen. It is over 99 pct Na2SO4 with main impurities being sodium chloride and magnesium sulphate. Iron content is less than 0.01 pct. As mentioned, the raw material at Monahans is a brine drawn from wells. Attention was first attracted to this location because a so-called alkali

Jan 1, 1954

By R. Wang, N. J. Grant, B. C. Giessen

By crystallographic and X-ray methods, the existence and isonzorphism of Ti3Rh5 and Hf3Rhs were confirmed. Both phases are of the orthorhombic Ge3Rh5 type; lattice parameters and refined positional parameters are given. The structure is related both to the filled-up NiAs-B8 and Cu-AI types. An analogous phase with zirconium does not exist; the effect of ternary substitutions for titanium ad hafnium suggests a size factor limit to be active. A recent survey of phase diagrams of the T4 metals titanium, zirconium, and hafnium with the T, noble metals rhodium and iridium indicated the existence of the A3B5 phases Ti3Rhs, ZrsRhs, and HfsRhs. Ti3Rhs and Hf3Rh5 were found to be isostructural, based on the line-rich powder patterns which had not been analyzed. Zr3Rh5 was considered to have a substructure of the NbRu type (orthorhombically distorted B2-CsCl type).&apos; Because, in combinations with other transition metals, hafnium and zirconium are generally more likely to form isostructural phases than hafnium and titanium (with the significant exception of the Ti2Ni-"E93" type phases based on T4 metals2), the reversal of this relation for the A3B5 phases was of interest. As shown in the following, the nonexistence of Zr3Rhs has been established, the structures of Ti3Rh5 and Hf3Rh5 have been worked out, and crystal chemical relationships and stability criteria are reported. EXPERIMENTAL METHODS AND RESULTS Alloy Preparation and Phase Diagram Work. Alloys were prepared from high-purity (99.99+ pct) elements by arc-meltin3,4.Heat-treated alloys were annealed in a vacuum of 3 x X torr for 24 hr at 1300DC. Metal-lographic samples were etched electrolytically in concentrated HCl with 5 v ac for 5 min.3 X-ray diffraction powder patterns were taken on a GE XRD-5 dif-fractometer with Cum radiation at low scanning rates (0.2 deg per min for 28). It was confirmed that Ti3Rhs and Hf3Rh5 have similar diffraction patterns, and that an alloy with the composition Zr3Rhs has a different pattern. Six Zr-Fh alloys with 59 to 69 at. pct Rh were therefore prepared and investigated in the as-cast state by X-ray diffraction and metallography. Alloys at 59 and 61 at. pct Rh were found to be a single phase, with the distorted B2-CsC1 type structure typical for the off-stoichio- metric region of the phase (Zr,-,Rh,)Rh. This phase forms a eutectic with ZrRhs at about 66 at. pct Rh: accordingly, alloys between 61 and 69 pct at. pct Rh consisted of two phases. There is no evidence for the existence of Zr3Rh5. Based on the results in Rafs. 1 and 5, on the present work on Zr-Rh, and on several additional alloys investigated, the portions between the AB and AB3 stoi-chiometry for Ti-Rh, Zr-Rh, and Hf-Rh are as follows: Further, several ternary alloys near Ti3Rhs and Hf,Rhs were prepared in which it was attempted to replace titanium and hafnium partly by zirconium, niobium, tantalum, and germanium. The results will be discussed in a later section. Structure Determination of Ti3Rh5. Since Ti3Rh5 and Hf3Rh5 are isostructural, the following discussion will largely deal with the former. Although the powder pattern of TisRhs is complex, as found previously,1 it could be indexed by comparison with other structures of A3Bs stoichiometry. Ti3Rh5 was found to be isostructural with Ge3Rh5, whose orthorhombic structure had been elucidated by Geller.9 As both the sizes and atomic numbers of germanium and titanium are comparable, the unit cell volume and the peak intensities could be expected to be similar; however, significant differences exist in the atomic positions, as will be shown. All lines in the powder patterns of Ti3Rh5 and Hf3Rhj could be indexed with primitive orthorhombic unit cells with the lattice constants: The fractional errors are 10 The low-angle portion of the indexed powder pattern of Ti3Rh with sin2 8 < 0.30 is listed in Table I. The extinction laws Okl only with k = 2n and hOl only with h - 2n are compatible with the space group Pbo2 and the more symmetrical space group Phnm of Ge3Rh5. Finally, the positional parameters of Ti3Rh5 and HfsRhs were refined under the assumption that titanium and hafnium occupy the germanium positions in Ge3Rh5. Integrated intensities were obtained from the diffraction patterns by planimetry. Intensities of overlapping reflections were separated by an iteration process incorporated into the least-squares positional refinement program according to a method described previously. The intensities of Ge3Rh5 were used in the first separation cycle, while the atomic parameters of Ge3Rh5 were used as starting values in the first refinement cycle. Absorption due to specimen

Jan 1, 1970

By F. R. Jones

AT Tahawus, N. Y., National Lead Co. operates the MacIntyre development. Here the world&apos;s largest titanium mine produces 5200 long tons of ore per day and pours 8000 long tons of waste rock over its dumps. Concentrated ilmenite is sent by rail to National Lead Co. pigment plants, and a second product, magnetite, is sold to steel producers in raw form or is agglomerated and shipped as sinter. Several earlier attempts had been made to produce iron from the deposits, which have been known since 1826. These attempts failed, chiefly because of titanium impurity. In 1941 the present owners reestablished the operation for production of war-scarce ilmenite, and the impurity became the main product. The Ore: The MacIntyre ore zone is about 2400 ft long and 800 ft wide in horizontal measurements. Ore outcrops were found on the northwest side of Sanford Hill, 450 ft above Sanford Lake and 2500 ft southeast. The zone dips at about 45" toward the lake and plunges to the southwest. The ore minerals, ilmenite and magnetite, are unevenly distributed in bands roughly parallel to the long axis of the ore zone and are interspersed with bands and horses of waste. Hanging wall ores are fine grained and grade from rich ore to waste rock or gabbro. Footwall ores are coarse grained and are almost entirely ilmenite and magnetite. The foot-wall waste rock, anorthosite, is the common country rock. Several faults cut the ore zone. These faults have no great displacement but do contribute to the great physical variations in ore rock and surrounding waste. The Mine: The MacIntyre mine is an open pit operation, with benches at 35-ft intervals. The lowest bench is now 54 ft below lake level. Loading equipment consists of three electric-powered shovels (a P & H model 1400 with 4-yd dipper and two Bucyrus-Erie models 85-B with 2%-yd dippers) and one diesel-powered shovel (a Northwest model 80D with 2%-yd dipper). Ore and waste are transported to a 48x60-in. jaw crusher in ten 22-ton Euclid trucks with 300-hp diesel engines. Ordinarily the two Bucyrus-Erie 2 % -yd shovels load ore into a fleet of three or four trucks. This combination works two 8-hr shifts per day, moving 5200 long tons of ore to the crusher and removing a small portion of the waste rock. The P & H model 1400 shovel, with a fleet of four trucks, loads waste on three shifts per day. The mine operates on a 5-day week, with a small maintenance crew working Saturday. Oversize rock is broken by a dropball handled by an Osgood model 825 rubber-mounted crane.&apos; Ore and waste are broken by drilling and blasting 9-in. diam vertical holes behind the benches. Bucyrus-Erie 42-T churn drills are used to drill the holes, which are extended 4 ft below the bench level on which the broken rock will fall. Drilling and Blasting History: In its early years the mine was equipped with Bucyrus-Erie 29-T churn drills, which drilled 6-in. holes. To keep up with production requirements the hole diameter was soon increased to 9 in., and by 1950 the three 42-T drills now in use had been acquired. Early blasting experiments with different kinds and grades of explosive led to adoption of 90 pct straight gelatin dynamite as standard. It was recognized that this explosive was expensive, and from the start of operations until 1950 extensive experiments were made using blasting agents of the ammonium nitrate family. Results were recorded as uniformly poor, with great build-up of oversize rock. The expense of these experiments, and the discouraging results, caused the abandonment of any expectation of breaking MacIntyre rock with anything but 90 pct straight gelatin dynamite. Further standardization led to 9-in. well drillhole spacings set at 16 ft in ore and 18 ft in waste, exceptions being permitted only for unusual conditions. The hole burdens were theoretically about 22 ft. Due to the extreme back-slope of bench faces, caused by blasting with heavy charges of dynamite, actual burdens were commonly well over 30 ft. Lack of precise control resulted in many holes having a burden as light as 15 ft. General practice was to stem 6 or 7 ft of hole with magnetite concentrate, the amount of stemming being left to the discretion of the pit foreman. Usually all holes in a row were fired instantaneously with Primacord detonating fuse. Millisecond delays were

Jan 1, 1957

By Walter C. Lawson

The primary objective in laying track in panel sections is to reduce the number of track laborers required. This is possible because the work is mechanized. Moreover, because the work is mechanized and each of the operations needs only a few men, and each is self-contained, the work can be carried on at night as well as in daylight; therefore, the method provides a means of preparing tracks on more than one shift. The laying of tracks in open pits and quarries in panel sections is not new but new methods have been made possible by the introduction of new types of equipment. The purpose of this paper is to describe the methods that are followed in the Morenci open pit. General Mining Operations Full-scale ore production at Morenci is about 50,000 tons daily. The normal yearly output of ore and waste is 32,000,000 tons, of which 30,000,000 tons is handled by rail haulage. This requires the building of approximately 47 miles of loading and other temporary tracks during a 12 months&apos; period (Fig I). Broken ore and waste is loaded into 90-ton capacity dump cars with 5-cu-yd full-revolving electric shovels. Shovel banks are uniformly 50 ft high. They are blasted with churn drill holes and the broken material from a blast is loaded out with two shovel cuts, the first one being called (locally) the "splatter" cut and the second one the "clean-up" or "face-up" cut. When a shovel is making its clean-up cut, the loading track is about 70 ft from the toe of the bank and, under normal conditions, a bank is blasted against it without removing the track. It is thus evident that each track is used for two shovel cuts before relocation is necessary, inasmuch as a single position serves for both the clean-up cut prior to blasting and for the splatter cut following the blast. The normal advance of a solid bench by a single blast is 40 ft (Fig 2). Preparation OF Panel Grade In preparation of panel grades bulldozers and rooters are used for the bulk of the work and an auto-patrol road grader for the final stage. At Morenci, bulldozers have always been used for track-grade preparation, but before the introduction of the other two types of equipment grades were uneven and irregular at best, and always necessitated a big gang of track laborers to hand-block under the ties with rocks after a track was laid into place. High blocking also made poor track because of instability and caused frequent derailments. Under these conditions derailments were generally bad as re-railing became difficult. Much track was torn up and many tics broken in the process. The inadequacy of the hand-blocked track, together with the inefficiency of hand blocking, constantly pointed, to the desirability of reducing the amount of labor required, so various means were tried to improve conditions, such as wood

Jan 1, 1949

By H. W. Hitzrot

THE new 4800-ton fine-grinding plant at the Hollinger Consolidated Gold Mines property at Timmins, in the Porcupine district of northern Ontario, went into operation in November 1937, and represents the culmination of an experimental program. The plant is a moderately low rectangular building of hollow tile on a steel frame, large enough to house four 7 by 15-ft. ball mills, with a 12 by 27-ft. classifier beside each mill. At one end is space for the addition of another mill and classifier or a mill and classifier for the regrinding of table concentrates. This regrinding is now done in the old grinding department of the main mill building. Also within the new building are the four 6-in. sand pumps for lifting the product from the low-dis- charge ball mills up to the classifier feed launders and the containers and appurtenances of a complete dust-collecting system. Together with the usual overhead crane, these constitute the major units of equipment within the new plant. The location is at the lower end of the main mill buildings toward the old tailings pond, now so neatly leveled off and sodded to rival the very best of our own W.P.A. projects. Close by the new grinding plant is a large dome-shaped structure-the new fine-ore bin designed arid built by Mr. Longmore and the Hollinger milling and engineering staffs. There are four separate automatically loaded inclined belt conveyors leading up from the bottom of the bin to the grinding plant. Each belt is equipped with a recording weightometer, in the grinding building. The whole structure and the machinery within it give the impression of permanence and a carefully integrated design with close attention to details, giving the operators every advantage for consistently good work. The many ideas and opinions behind this achievement were all ably organized and executed by the Hollinger milling and engineering staffs, anti not a few were directly initiated by them. Excellent cooperation was afforded by the Hollinger staff to the engineers helping to conduct the grinding and classification test program. It was the author&apos;s privilege

Jan 1, 1939

By Rudolf Gahl

Page Tests Conducted in Small Test Mill................... 577 Demonstration Tests Conducted by Minerals Separation Co....... 577 Flotation Tcsts Conducted by Inspiration Co............. 577 Sampling of Orebody........................ 578 Other Results Obtained in Small Test Mill.............. 580 Tests Conducted in Large Test Mill................... 580 Flow Sheet............................. 580 Discussion of the Value of Preliminary Table Treatment......582 Callow Flotation Installation..................... 585 Flinn-Towne ~nstallation...................... 587 Cole-Bergman Installation...................... 588 Methods Followed in Competitive Tests................ 590 Advantage of Pneumatic Flotation Machines.............. 591 Pneumatic Machines of Minerals Separation Co............. 591 Float Skimming Device......................; 594 Experimental Inspiration Flotation Machine.............. 596 Arrangement of Callow Cells in Series ................ 598 Variations of Flow Sheet....................... 599 Coal Tar as Flotation Agent..................... 600 Experience with Primary Slime.................... 602 Influence of Iron on Flotation..................... 605 Influence of Chemicals on Primary Slime............... 607 Fineness of Crushing Desired.................... 607 Operation of Large Concentrator..................... 608 Flow Sheet of Callow Sections.................... 608 Flow Sheet of Inspiration Sections.................• 609 Inspiration Flotation Machine of Steel Construction.......... 610 Minerals Separation Section..................... 613 Filter Plant............................ 613 Results Obtained in Commercial Concentrator............... 616 Tonnage............................... 616 Air and Power Consumption...................... 616 Floor Space............................ 617 Water Consumption......................... 617 Recovery............................. 618 Oil Consumption.......................... 618 Operating Costs for Flotation..................... 620 Discussion of Results Obtained.................... 620 Prospects for Futurc Development of the Flotation Process......... 621 Porous-Bottom Experiments..................... 622 Raising the Grade of Concentrates.................. 624 Recovering Carbonates by Flotation................. 624 Recovery of Silicates by Flotation.................. 627 General Theory......................... 628 Conclusion............................... 630

Jan 1, 1917

By R. M. Caitlin

QUITE a number of years ago in looking for basic facts, it seemed obvious, in view of an unquestion-able supply of raw material and an extensive requirement probable in the near future, that the funda-mental requirement of any shale-oil industry was mass production &apos;by a continuous process. This decision greatly simplified matters, as it eliminated all considera-tion of externally-heated retorts, and all batch processes, which only utilize a part of the capacity of the interior space because, unless the ashes are removed as rapidly as formed, the space occupied by them is dead, instead of being occupied either by shale in active distillation or in drying out and heating up preparatory thereto. A second imperative and basic necessity soon appeared as a natural sequence, namely, the fixed carbon of the spent shale must be utilized to supply the heat for the eduction of the oil. PRODUCTION OF THE CRUDE As the production of the crude oil is the first and most important step in the utilization of oil-shale, being the only source from which the multitude of possible by-products can come, each by a special treatment of the crude oil, I will devote the time allotted to me to the subject of crude oil production-its cost expressed in terms of tons treated per man per shift. The costs of mining the shale and refining the crude shale oil vary with local conditions and are not specially influenced by the source of the crude. But the cost of distilling the shale in terms of tons per man shift seems to be the basis of any proper comparison of costs. After considerable experimenting, ranging from laboratory tests up to and including quantities of fifteen to twenty tons, it was evident that a plant might be made up of an indefinite number of units operating in concert. The economic size of the units, however, would .have to be determined by experiment. The general theory of our process contemplates a regulated combus-tion of the fixed carbon in the spent shale, in its incan-descent condition after all the oil has been driven out of it; and a transfer of the resultant heat to the mass of raw shale above.

Jan 1, 1927

By D. W. Gentry, H. E. Sherer

Determining the age at which to replace a specific piece of mining equipment, and choice of the best possible replacement, is a problem common to nearly all mining operations. This paper examines the data required for intelligent equipment replacement decisions and discusses how to predict future repair cost from historic data, determine the total cost of various replacement alternatives, and evaluate the different replacement alternatives. Various operations research and computer methods were used to develop this easily-used, practical equipment replacement method.

Jan 1, 1984

By George E. Beavers

Under the title used for this paper, the converter practice of the Tennessee Copper Co. is described in the TRansactions of the Institute.l That article contains the following statement: "The limit in capacity of the Peirce-Smith converter in terms of concentrate has not been reached but approximately as high as one ton of concentrate has been handled for each ton of liquid matte charged and good working conditions have been maintained." It is not the intention of the writer to review the conditions leading up to the introduction of a Peirce-Smith converter at Copperhill, but, instead, to offer later data to show how satisfactory the installation has been. Converter Campaign, June 15, 1930 to August 23, 1931 Blowing time (converter days)............... 349.90 Number of blows........................... 427.00 Tons matte charged........................ 38,335.00 Copper assay of matte, per cent.............. 13.67 Tons blister copper made.................... 9,246.00 Time to blow one ton of copper, minutes...... 54.50 Air used per minute, cu. ft................... 12,500.00 Blast pressure, lb........................... 12.80 Air per ton copper, cu. ft.................... 681,330.00 Air per ton iron, cu. ft....................... 199,040.00 Tons flux used............................. 11,845.00 Tons flux per ton matte..................... 0.31 Tons flux per ton copper.................... 1.28 Tons flux per ton iron....................... 0.37 Tons concentrate treated.................... 28,960.00 Copper assay of concentrate, per cent......... 17.13 Tons concentrate per ton matte.............. 0.76 Tons material charged per converter day...... 235.70

Jan 1, 1934

By Henry R. Linden

The demand for natural gas continues to increase at higher than anticipated rates, partly because of its widening price advantage over most other fossil fuels when the cost of air-pollution control is included. However, there are clear indications that the natural gas supply from the conliguous 48 states and continental shelves will not keep up with this rapid growth in demand indefinitely. Projections are presented which define the extent of potential deficiencies from the 1970&apos;s to the year 2000. Among the sources of supplemental gas - imported pipeline natural gas from Canada and Mexico, tanker import of liquefied natural gas, and synthetic pipeline gas from coal and oil shale -by far the most abundant at potentially competitive costs is pipeline gas from coal. The state of development and relative economics of the various coal gasification processes are reviewed. It is shown that synthetic pipeline gas could become a very substantial market for bituminous coal and lignite at current mine-mouth prices - 60-70 million tons of coal for each trillion cubic feet of synthetic pipeline gas produced. This corresponds to only slightly more than the current annual increase in gas demand. Although annual discoveries (gross additions to proved reserves) of natural gas in the United States are still on a general upward trend from the current level of 22 trillion cu ft annually, most forecasters do not expect this to increase substantially in the foreseeable future. For example, the updated (to include 1966 and 1967 data) mathematical model of natural gas discovery and production in the U.S. developed by the Institute of Gas Technology (IGT)&apos; projects that discoveries will level out at about 25 trillion cu ft annually in the late 1970&apos;s and during the 1980&apos;s and then decline to about 21 trillion cu ft by the year 2000 (Fig. 1). This adds up to a new supply for the period 1968-2000 of about 790 trillion cu ft. Experts who usually reflect the producers&apos; viewpoint, such as Radford L. Schantz of Foster Associates,* are relatively more pessimistic. In contrast, a forecast just made by the U.S. Dept. of the Interior is much more optimistic.3 It assumes an increase in gas discoveries of 2.2% per year over the period 1965-80, reaching about 30 trillion cu ft in 1980. If this rate of increase were extended to the year 2000, annual discoveries would reach 46 trillion cu ft at that time, for a total over the period 1968-2000 of about 1100 trillion cu ft. To these forecasts of new gas discoveries must be added proved reserves of roughly 290 trillion cu ft,4 bringing total U.S. supplies for the rest of the century to nearly 1100 trillion cu ft (IGT) and possibly as high as 1400 trillion cu ft (U.S. Dept. of the Interior). This is approximately the same range as that of two estimates of total remaining recoverable natural gas supply: Potential Gas Committee, 980 trillion cu ft5 and IGT, 1450 trillion cu ft.6 Only the 1965 estimate by the U.S. Geological Survey7 suggests that economically recoverable natural gas supplies will not be exhausted around the end of the century. These forecasts are, naturally, based on the assumption that changes in technological, economic, and regulatory environment as they affect the gas industry will be of an evolutionary, not revolutionary, nature. The various forecasts of potential natural gas supply must now be compared to forecasts of natural gas demand (Table I). The general consensus is that the recent Future Requirements Committee projection to 1990&apos; (extended to the year 2000 by the most recent U.S. Bureau of Mines (USBM) projection9) represents the minimum gas requirements (Table 11). They add up to a total of 1030 trillion cu ft for the period 1968-2000. Even this minimum anticipated gas demand exceeds the total remaining supply estimate by the Potential Gas Committee and would nearly exhaust the proved reserves plus new discoveries projected by IGT. The supply situation would appear much tighter if the demand projections of the Texas Eastern Transmission Gorp.10 and the American Gas Assn.(A.GA.)&apos;&apos; were used (Table I). Yet, these higher forecasts probably do not include the effects of such new markets as gas fuel cells, use of liquefied natural gas as a transport fuel, etc. They also may not fully reflect the impact of air quality control on the fuel market. Obviously, the probable discrepancy between projected supply and demand can only be accommodated in four ways. 1) Rapid increase in exploration and drilling activity to provide new supplies in the amount projected by the optimistic U.S. Dept. of the Interior forecast, coupled with an increase in net pipeline imports from Canada and Mexico from the present 0.5 trillion cu ft per year

Jan 1, 1970

By H. Rush Spedden

R. T. Hukki has extended his study of ball mill grinding at supercritical speeds with an excellent mathematical analysis of tumbling mill grinding. When he speaks of supercritical speeds he is referring to the original Fahrenwald critical-speed formula. He said that, as an example of the use of supercritical speeds, if a fine grinding mill of any type is wet-grinding ore of 3.5 sp gr with steel balls at a certain conventional subcritical speed, the same power input and capacity should be obtainable with autogenous medium of 3.5 sp gr at a speed 100 to 120 pct of the critical in a grate- type mill of the same effective size. In addition, he introduced what he calls the base mill concept which, he stated, makes it possible to compare performances of mills of different sizes grinding with a metallic medium or with an autogenous medium of any specific gravity and at any speed. He showed the use of this concept and explained how it makes possible the evaluation of mill sizes and motors for any grinding purpose at any accuracy well within the conventional standards of design in milling practice. He further stated that the maximum capacity in pilot plant mills with various media, either metallic or autogenous, has always been found to be within the supercritical speed range. In his discussion of this paper he substantiated these findings with statements showing the increased capacity obtained in a milling plant in Finland which followed his principles.

Jan 7, 1960

By Eckley B. Coxe

THE plummet lamp, to which I called the attention of the Institute, at the Bethlehem meeting, in August, 1871, with the improvement of the compensating ring, suggested by Mr. Heller, having come into general use for mine surveying in this country, and my attention having been called to the fact that it could not be employed in mines in which there was danger of meeting with fire-damp, I have so modified it that it can be used in all cases with safety. Mining engineers, who are in active practice in those districts where fire-damp is met with in the mines (and I am sorry to say it is becoming much more common in the anthracite regions), know how dangerous their work is when they are called upon to survey such mines, particularly when they are obliged to run lines in those parts of a mine which have been unworked, since by opening of doors, brattice, etc., to get the sights, they are liable to disarrange the currents of air, and cause any fire-damp that may have accumulated in the old workings to find its way into the levels, etc., where the party is at work. It is, therefore, very dangerous to leave an open light (such as the original form of plummet lamp) in an old breast or gangway, even when the safety lamp has shown that no fire-damp is present, for the opening of the doors, etc., may drive the fire-damp to the light, and thus endanger the lives of the engineers. The improved form of plummet lamp, now shown to you, can be used either with or without the safety apparatus. Upon the top of the plumb-bob portion of the old lamp a screw is cut, upon which a ring A is screwed. (See Plate II.) On the external cylindrical part of this ring two small conical holes are drilled, 180° apart. The compensating ring, by which the plumb-bob part of the lamp is suspended, passes over the ring A, and is fastened to it by two small screws having conical points, which fit into the conical holes in the ring A. The safety apparatus resembles, to a certain extent, that of the Mueseler lamp. It consists of a ring B and plate C, which are united by four rods. The plate C has a cylindrical hole in the middle, and four apertures distributed radially around it. In the central cylindrical hole is fitted a conical brass chimney, which projects below the plate C, and is fastened to the latter, being kept ver-

Jan 1, 1875

Discussion of the paper Of NOEL CUNNINGHAM, presented at the New York meeting, February, 1915, and printed in Bulletin No. 99, March, 1915, pp. 601 to 608. C. H. POIRIER, New York, N. Y. (communication to the Secretary*). -Mr. Cunningham&apos;s paper, written from the standpoint of a stamp advocate, while commenting more or less favorably upon the installation of ball mills in the Vipond plant, does not, in my opinion, give as much emphasis to the comparatively new departure as the installation of ball mills in the place of stamps justifies. This discussion is based upon my personal and intimate practical work for several years with stamp mills, and for the past three years with Hardinge ball and pebble mills. The fact that the Vipond mine contains about equal quantities of the A and B classes of ore mentioned by Air. Cunningham, and the further fact that I have had a most intimate knowledge of the working of both classes of ore in the Porcupine district in stamp mills and ball mills, justifies upholding my final decision to use ball mills in the place of stamps, and defends my present further action in now increasing the present Vipond capacity by the addition of another 6-ft. Hardinge ball mill, in which action the directors of my company concur. This is one of the strongest evidences I can possibly offer in substantiation of my opinion that the ball mill exceeds the efficiency of the stamp, both in metallurgical and mechanical economy. It is hardly fair to compare a 100-ton per clay plant with a mill handling several times this amount, yet it is my belief that the cost per ton. of grinding in the ball mill is far less than that of any stamp mill in the district, where capacities run up to 400 tons per clay.

Jan 5, 1915

By A. S. Bower

Any process which has for its object the preservation of iron and steel from rust, and which will make these metals more applicable than they now are to the requirements of mankind, will be sure to meet with attention from members of this association, and from all those who are either engaged in the extraction of the ore, its reduction to metal, or the subsequent application of the metal itself. It is, perhaps, not too much to say that when iron and steel are rendered secure against corrosion and decay, they will be used to an indefinitely greater extent than they now are. The whole realm of science has, therefore, been explored in the attempt to discover some method by which the formed article may be preserved, leaving its strength undiminished by the destructive action of rust. Paints, oils, varnishes, glazes, enamels, galvanizing, electro-depositing and what is called "inoxidizing" are among the many systems now in vogue to effect the preservation of iron and steel from the corrosive action of air and water. The object of this paper is to show what may he done in protecting iron and steel from rust by forming upon their surfaces a film of magnetic oxide by an inexpensive process. It is no new thing to be told that magnetic oxide of iron is unaffected by exposure to the atmosphere or to salt water for any length of time. The black sand of Taranaki, in New Zealand, is a sufficiently good example of this. Dr. Percy has pointed out that the reason why Russian sheet iron is less affected by exposure than ordinary sheet iron is because of a coating of magnetic oxide; but this was not known

Jan 1, 1883

By J. G. Benford, E. B. Stanley

THERE have been numerous papers in the literature1 on the subjects of secondary and tertiary recrystalli-zation in silicon steels. Secondary re crystallization is believed to occur in silicon steel by either a surface-energy phenomenon such as in the usual development of cube texture or by a second-phase phenomenon such as in the usual production of cube-on-edge texture, (110)[001]. Tertiary recrystallization in silicon steel is thought to be a surface-energy phenomenon in which, for example, grains having a (110) plane parallel to the sheet grow at the expense of other grains in the matrix including those having a (100) plane parallel to the plane of the sheet. In all these instances, the orientations involve either a preferred (100) or (110) plane in the plane of the sheet. Until very recently, there had been no experimental evidence reported of the occurrence of a texture by secondary or tertiary recrystallization that involves a (111) plane in the plane of the sheet, although Kohler reported that grains having the (111) plane parallel to the sheet surface can also grow by a surface energy mechanism. Stickels observed a secondary texture in iron described as "near {554}(225)" about 5 deg from {lll}(211).3 Mee reported that in a vacuum-remelted commercial 3 pct Si steel {lll}(hkl) secondary recrystallization took place in a high vacuum and in pure hydrogen.4 Recently in our Laboratory, large-grained structures such as shown in Fig. 1 having an orientation near (111)[211] or (111)[2ii] have been observed. The arrows point to areas of relatively small matrix grains of the kind that the much larger (111) grains consumed while growing. It is of interest that the matrix grains of samples annealed at 2000°F were essentially the same size as those in samples annealed at 2200°F, a matrix-grain-size stability that is characteristic of secondary recrystallization processes. A torque disc taken from Grain 4 of the sample shown in Fig. 1 revealed a very flat magnetic-torque curve, as expected, with a maximum torque of 7000 dyne-cm per cu cm compared to the typical 180,000 dyne-cm per cu cm observed for conventional (110)[001] textured material. A back-reflection Laue pattern for Grain 4 is shown in Fig. 2 and indicates a near-perfect (111)[211] orientation. The other six numbered grains in the sample of Fig. 1 had a similar orientation. The small circles next to each number were the target areas for the X-ray beam. The starting material was an 0.011-in.-thick oriented silicon steel, (110)[001] texture, containing 3 pct Si. It was lightly pickled, cold-rolled to 0.005 in., and annealed 4 hr at 2200°F within a nickel box (not gas-tight) inside a tube furnace through which dry hydrogen was flowing. The samples were heated to 1500°F in 1 hr and then at 60°F per hr to 2200°F. There were other

Jan 1, 1969

By William P. Kimball, Morris Cohen

This paper deals with the calculation of the composition of the infinitesimal trace of alloy that transfers from the liquid to the solid state at each temperature during the equilibrium solidification of a binary solid solution, and which thereby enables the compositions of the coexisting liquid and solid phases to follow along the liquidus and solidus lines respectively during the cooling. A general expressioll for the composition (6) of the liquid-to-solid transfer at each temperature has been derived: , = Zlxl{xl - P) + ZsXsiP - xs) [I] Zl(xl -P)+ Zs{P - xs) where ZL and Zs are the slopes of the liquidus and solidus lines at the given temperature, xl and xs are the compositions of the stable liquid and solid phases at the same temperature, and P is the composition of the alloy under consideration. The d equation is valid for the process of equilibrium heating as well as cooling, and may be applied to vapor-to-liquid, vapor-to-solid, liquid-to-liquid, and solid-to-solid transfers if the corresponding equilibrium diagrams are known. The d-versus-temperature curves for two alloys P1 and P2 are shown in Fig. I. In each case, the liquid-to-solid transfer has the same composition as the stable solid phase only at the temperature of the beginning of solidification, and has the same composition as the stable liquid phase only at the temperature of the completion of solidification. At each intermediate temperature, the composition of the liquid-to-solid transfer differs by a finite amount from those of the two coexisting phases. Therefore, during equilibrium cooling. the transfers must merge into the solid phase from the liquid without forming a transition phase; otherwise the condition of equilibrium would be violated. At any given temperature during solidification, the composition of the liquid-to-solid

Jan 1, 1941

By B. M. Larsen, T. E. Brower

IN an earlier paper1 we discussed a simple, rapid method of taking samples of liquid steel and analyzing them for oxygen, which, though possibly not absolutely accurate (as is likewise true of all other methods), certainly yields results that are satisfactorily consistent. Accordingly, samples from hundreds of heats in different shops were analyzed for oxygen, with results sufficient in number to be handled statistically and permit estimation of some general trends. Measurements were made in acid as well as in basic open hearths, throughout the refining period, to learn how stirring, blocking, adding ore or lime or sand, affects the oxygen content of the bath; we also followed the changes brought about by tapping, teeming, and deoxidizing. Some of these results, discussed in an earlier paper.2 bring out the dominant role of the carbon-oxygen reaction in regulating degree of oxidation both of metal and of slag, also the marked variability of concentration of dissolved oxygen [0] in excess of that which would be in equilibrium with carbon and with carbon monoxide at a partial pressure of one atmosphere. As a logical beginning on this complex problem, we take up in the present paper the variability of this excess oxygen, ?[O], when other factors are as constant as they ever are in open-hearth operation; namely, toward the end of the refining period, when the bath may be regarded as in the comparatively steady state it approaches in absence of disturbing factors. This condition was chosen because by that time the significant reactions, except carbon oxidation, between slag and metal have come to substantial equilibrium; this facilitates interpretation of the complex situation and thus permits more definite conclusions to be drawn. This excess concentration of oxygen, ?[0], in the metal is needed, of course, to make the steelmaking process go at a reasonable rate; alternatively it may be regarded as a measure of the virtual pressure increment above one atmosphere, or of the degree of supersaturation, of carbon monoxide in the metal. According to our measurements, the excess concentration ?[O] in liquid steel varies from about 0.009 to 0.035 per cent oxygen by weight. It is quite sensitive to change of conditions, being altered temporarily by operations such as stirring with green poles, additions of ore, lime, or sand; but as the disturbance works itself out, it resumes a level within the intermediate range characteristic of the steady state. The conditions most common in average furnace practice are covered by the following : [ ] as in a reasonably steady state-that is, when it is boiling normally, is at proper temperature with a well-shaped slag, and has been free from disturbing effects during the preceding half hour-?[O] returns from

Jan 1, 1946

By P. Dayal, L. S. Darken

THE migration of carbon in austenite under the influence of an electric current has been observed qualitatively several times.14 Lebedev and Guterman5 recently have reported quantitative measurements; their method consisted of welding a low-carbon to a high-carbon wire, passing current, and later estimating the carbon distribution metal-lographically. We believe the method reported in this paper is superior in principle since electrolytic migration and ordinary diffusion are not necessarily coupled as in the weld method; also for the first time the extent of migration is determined by combustion analysis for carbon. A uniform tubular specimen (S.A.E. 1045 or 1095) was mounted as illustrated in the figures. the whole assembly being in an atmosphere of purified nitrogen. Direct current (129 to 226 amp at 0.65 to 1.0 v) served as source both of heat and of potential gradient for carbon migration. The duration of experiment was 7.5 to 12 hr, during which time the temperature was controlled (±10°C) manually. The experimental conditions are indicated in the first five columns of table I. With this experimental arrangement, the temperature initially has a maximum value at the central plane. Also, in this vicinity (by virtue of the symmetry), the carbon entering any volume element is equal in quantity to that leaving; the loss or accumulation of carbon occurs near the electrodes since the carbon moves uniformly near the center and is "frozen" at the cold ends. Hence, providing the time of experiment is not sufficiently long to seriously influence the conditions at the central plane, carbon crosses this plane only under the influence of the electrical potential gradient and not under the influence of temperature or concentration gradient. The amount of carbon which has crossed this plane was determined by combustion analysis of the two halves of the specimen. The results of these analyses are shown in the sixth and seventh columns of table I. It will be noted that substantial amounts of carbon migrated from the anode portion to the cathode portion (except at 920°C, which temperature was too low to exhibit the effect in the allotted time). In spite of precau-tions taken, considerable decarburization occurred as may be seen by comparing cols. 8 and 5. In three cases (indicated by asterisks in table I) the specimen was ground on one side, polished, and examined metallographically before analysis. One specimen was normalized and re-examined. Micrographs of selected areas in specimens 4 and 6 are shown in figs. 1 and 2, respectively. Evidence of carbon migration from the anode toward the cathode is quite apparent. Fig. 2 shows abundant graphite as well as cementite in a region near the cathode. The temperature of this zone is estimated at about 800°C. In fig. 1, particularly in the micrograph on the extreme right (the right side of which is of unaltered carbon content), there is evidence of slight depletion of carbon in the immediate vicinity of the cathode as contrasted to the general increase in carbon of the cathode half of the specimen. Although this may be attributed in part to decarbur-ization, it is believed that it is occasioned also by thermal diffusion—migration (of carbon) from a cool to a hot zone4—a phenomenon superimposed upon the electrical migration. Evidence of carbon migration was visible particu-larly during the course of the high-temperature,

Jan 1, 1951

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons. ) The governing body of the Imperial College of Technology, London, S. W. (Royal School of Mines), will shortly proceed to the appointment of a Professor of Metallurgy. This important Chair has been filled in the past by such eminent metallurgists as John Percy, Sir William C. Roberts-Austen, and others. A large manufacturing company having two iron foundries, blast furnace, etc., requires the services of a chemist, metallographist, and metallurgical engineer qualified to give advice on cast iron practice, and to prescribe remedies for difficulties often met with in the usual iron foundry. The position of converter blower at a side-blow Bessemer steel casting plant is vacant.

Jan 5, 1913

Alfred Noble Joint Prize Committee F B Foley, &apos;56 American Documentation Institute F B Foley, &apos;56 American Geological Institute J L Gillson, Nov &apos;56, H A Meyerhoff, Nov &apos;57 Committee on Government Relations J L Gillson, &apos;56 American Power Conference Paul R Nichols, &apos;56 American Standards Association Mining Standards Board E R Borcherdt, Jan &apos;58, Otto Herres, Jan &apos;58 Alternates E W Bullard, Dec &apos;56, and J K Richardson, Dec &apos;56

Jan 1, 1956