Search Documents

By P. V. Martin

Shortly after the middle of the nineteenth century, the invention of the regenerative open-hearth furnace and the development of the Bessemer process stimulated a rate of steel production whose magnitude created an unprecedented demand for pig iron. Revolutionary improvements in furnace design, auxiliary equipment, and operating technique enabled the blast furnace to keep abreast of the constantly increasing requirements of the steel mill. The development of improved blowing equipment, more adequate facilities for material handling, and particularly the general use of anthracitc and coke to replace the physically weaker charcoal, led to a rapid expansion in both the height and volume of furnaces. Beyond a doubt, however, the greatest single factor in blast-furnace improvement at this time was the use of the higher blast temperatures made available by the replacement of the recuperative iron pipe stoves by the regenerative Cowper brick stove. The increased blast temperature not only resulted in greater output but also reduced fuel consumption . far more than could be explained by the additional heat content of the blast. The progress of iron manufacturing was thus largely mechanical and thermal. Little attention was given the chemistry of the process until the publication of the investigations of Sir Lowthian Bell.1 Bell's painstaking experiments and investigations gave to the blast-furnace man his first real scientific conception of blast-furnace chemistry. Bell's recognition of the dual function of the carbon, the technical importance of reversible reactions and chemical equilibria, and his conception of the degree of oxidation of the carbon as shown by the analysis of the outgoing gases as a criterion of furnace efficiency, laid the foundation upon which has since been erected the structure of blast-furnace theory. Prominent among those availing themselves of Bell's data as .a basis of further study was M. L. Gruner,2 professor of the French School of Mines. His "Blast Furnace Phenomena," published in 1870, presented

Jan 1, 1940

By Charles Macdonald

It may seem to be almost unnecessary to occupy the time of the Institute in further consideration of a question which has been so comprehensively treated in papers already on file in our own Transactions and in those of the American Society of Civil Engineers. Unfortunately, however, the results of these concerted efforts have not been materially to increase our stock of Knowledge in the direction sought for; and as the necessity for this information is becoming.more and more apparent as the demand for structural materials increases, it is believed that by continuing the agitation by means of discussions in this and kindred societies, whose members are vitally interested in obtaining reliable data as to the properties of the materials they are called upon to work with, public opinion may be educated up to the importance of exerting such an influence upon the law-makers of the country as will result in the formation of a competent board, with adequate means at its disposal, to carry out this great work in a manner alike acceptable to the makers and users of the materials in question. It may be proper in the first place to glance briefly at what has been attempted thus hr, then to indicate some of the more important lines of needed investigation, and finally to consider reasons why government aid may with propriety be sought for in carrying on the work. At a convention of the Society of Civil Engineers held at Chicago June 5th, 1872, it was, on motion of General William Sooy Smith, resolved, that, " Whereas, American engineers are now mainly dependent upon formula for the calculation of strength of the different form of iron and steel, not based on experiments upon American materials and manufacture; and " Whereas, There differ greatly in many of their ch~racteristics front thoae of foreign production, both in their nature and forma: therefore,

Jan 1, 1882

Through a unique Department of Commerce program a group of US mining equipment manufacturers spent 18 fruitful days in the, Far East, meeting with government and industry leaders in Thailand, Indonesia, and the Philip¬pines. The US Mining and Exploration Equipment Semi¬nar Mission, held April 3-20, 1979, was sponsored by the Special Activities Group of the Commerce Department's Office of International Marketing. The program included a series of technical overview papers presented by the manufacturers, aimed at promoting the sale of US products and services throughout the world.

Jan 7, 1979

By Keith Leonard Sutherland, Ian William Wark

Mercaptobenzthiazole and its sodium salt are marketed under the trade names Flotagen and Flotagen S respectively, for use as collectors for cerussite and other minerals. The structural formulas for sodium rnercaptobenzthiazole and for sodium ethyl xanthate are: Chemically there is a resemblance between the two compounds, though the free acid (mercaptobenzthiazole itself) is much more stable than xanthic acid. Both are readily oxidized, e.g., by iodine to disulphides, and can be estimated by iodometric titration. Qualitatively they are similar as collectors in flotation, although there are quantitative differences between them that may be important in practice. It is deduced that the influence of the nitrogen atom is subordinated to that of the sulphur atoms, and that the dominant group of these compounds is the mercapto group —SH or —5Na. The general method of investigation has been based on contact tests. Two temperatures, 10" and 35" C., have been chosen, and with a standard concentration of 20 mg. per liter of mercaptobenzthiazole (i.e., of the free acid) the influence of alkali, cyanide and copper sulphate on contact at sulphide mineral surfaces has been studied. This standard concentration corresponds to about 19 mg. per liter potassium ethyl xanthate; it brings out the differences between the minerals better than a higher concentra-

Jan 1, 1939

By Ian Wark

MERCAPTOBENZTHIAZOLE and its sodium salt are marketed under the trade names Flotagen and Flotagen S respectively, for use as collectors for cerussite and other minerals. The structural formulas for sodium mercaptobenzthiazole and for sodium ethyl xanthate are: Chemically there is a resemblance between the two compounds, though the free acid (mercaptobenzthiazole itself) is much more stable than xanthic acid. Both are readily oxidized, e.g., by iodine to disulphides, and can be estimated by iodometric titration. Qualitatively they are similar as collectors in flotation, although there are quantitative differences between them that may be important in practice. It is deduced that the influence of the nitrogen atom is subordinated to that of the sulphur atoms, and that the dominant group of these compounds is the mercapto group -SH or -SNa. The general method of investigation has been based on contact tests. Two temperatures, 10° and 35° C., have been chosen, and with a standard concentration of 20 mg. per liter of mercaptobenzthiazole (i.e., of the free acid) the influence of alkali, cyanide and copper sulphate on contact at sulphide mineral surfaces has been studied. This standard concentration corresponds to about 19 mg. per liter potassium ethyl xanthate; it brings out the differences between the minerals better than a higher concentra-

Jan 1, 1939

By Ian William Wark, Keith Leonard Sutherland

MERCAPTOBENZTHIAZOLE and its sodium salt are marketed under the trade names Flotagen and Flotagen S respectively, for use as collectors for cerussite and other minerals. The structural formulas for sodium mercaptobenzthiazole and for sodium ethyl xanthate are: [ ] Chemically there is a resemblance between the two compounds, though the free acid (mercaptobenzthiazole itself) is much more stable than xanthic acid. Both are readily oxidized, e.g., by iodine to disulphides, and can be estimated by iodometric titration. Qualitatively they are similar as collectors in flotation, although there are quantitative differences between them that may be important in practice. It is deduced that the influence of the nitrogen atom is subordinated to that of the sulphur atoms, and that the dominant group of these compounds is the mercapto group -SH or -SNa. The general method of investigation has been based on contact tests. Two temperatures, 10º and 35º C., have been chosen, and with a standard concentration of 20 mg. per liter of mercaptobenzthiazole (i.e., of the free acid) the influence of alkali, cyanide and copper sulphate on contact at sulphide mineral surfaces has been studied. This standard concentration corresponds to about 19 mg. per liter potassium ethyl xanthate; it brings out the differences between the minerals better than a higher concentra-

Jan 1, 1939

By Ian William Wark, Keith Leonard Sutherland

Mercaptobenzthiazole and its sodium salt are marketed under the trade names Flotagen and Flotagen S respectively, for use as collectors for cerussite and other minerals. The structural formulas for sodium rnercaptobenzthiazole and for sodium ethyl xanthate are: Chemically there is a resemblance between the two compounds, though the free acid (mercaptobenzthiazole itself) is much more stable than xanthic acid. Both are readily oxidized, e.g., by iodine to disulphides, and can be estimated by iodometric titration. Qualitatively they are similar as collectors in flotation, although there are quantitative differences between them that may be important in practice. It is deduced that the influence of the nitrogen atom is subordinated to that of the sulphur atoms, and that the dominant group of these compounds is the mercapto group —SH or —5Na. The general method of investigation has been based on contact tests. Two temperatures, 10" and 35" C., have been chosen, and with a standard concentration of 20 mg. per liter of mercaptobenzthiazole (i.e., of the free acid) the influence of alkali, cyanide and copper sulphate on contact at sulphide mineral surfaces has been studied. This standard concentration corresponds to about 19 mg. per liter potassium ethyl xanthate; it brings out the differences between the minerals better than a higher concentra-

Jan 1, 1939

The Murray Plant of the American Smelting & Refining Company is situated seven miles south of Salt Lake City, and has a fine view of the Salt Lake Valley with its fertile farms and orchards. It is located on the Los Angeles & Salt Lake and Denver & Rio Grande Western Railroads, and has a fine electric car service, cars running every 15 minutes. The beautiful and majestic Wasatch range lies about five miles to the east and the Oquirrh Range to the west, and from these mountains a large proportion of the ores treated are obtained.

Jan 1, 1925

By A. J. Heckler, J. A. Peterson

A capsule technique was successfully employed to investigate the effect of nickel on the activity of nitrogen in Fe-Ni-N austenite in the temperature range 600" to 1200°C. This technique consisted of equilibrating nitrogen among various Fe-Ni alloys within a sealed silica capsule. Nitrogen transfer among the specimens occurred by N, gas at 900°, lOOO? and 1200?C. Nitrogen gas pressures within the capsules were estimated to be as high as 22 atm. The activity coefficient of nitrogen, fN , in Fe-Ni-N austenite is adequately described by the linear interaction equation: log . wt pct Ni where the standard state is chosen such that fN = I as wt pct Napproaches zero in binary Fe-N. This relationship was determined over the temperature range 873" to 1473°K and for nickel contents of 0 to 35 wt pct. ALTHOUGH chemical thermodynamics of liquid iron alloys have been extensively studied, experimental data for the solid state are needed. These thermody-namic data will provide a basis for understanding phase transformations, precipitation reactions, metal-gas equilibria, and so forth. The interaction of sub-stitutional alloying elements with the interstitial elements is of particular interest. In this investigation the thermodynamic behavior of Fe-Ni-N austenite has been studied. The solubility of nitrogen gas in iron austenite is known to obey Sieverts&apos; law up to about 65 atm.1-6 In addition, the solubility of nitrogen in Fe-Ni austenite has been investigated5"8 using the classical method of equilibrating Fe-Ni alloys with nitrogen gas at 1 atm. A capsule technique similar to that used to study the activity of carbon in alloyed austeniteg&apos;&apos;&apos; was employed in the present work to determine the effect of nickel on the activity of nitrogen in Fe-Ni austenite over the temperature range 600" to 1200°C. EXPERIMENTAL PROCEDURE A series of Fe-Ni alloys up to 35 wt pct Ni was vacuum melted and cast into 1 by 3 by 6 in. ingots. Chemical analyses at the top and bottom of each ingot demonstrated that the ingots were homogeneous with respect to nickel content. The nickel contents are given in Table I. Additional chemical analyses showed that wt pct Si < 0.05, s < 0.01, C < 0.01, Al < 0.006, 0 < 0.004, Mn < 0.002, and P < 0.002. A 2 in. section of each ingot was cold rolled to 0.015 in. The material was then decarburized to a carbon content of less than 0.004 wt pct. A portion of the material of each nickel content was nitrided to various levels in a H2-NH3 gas atmosphere to provide a source of nitrogen during subsequent equilibration. The experimental technique consisted of equilibrating the series of Fe-Ni-N alloys in a partially evacuated sealed silica capsule at the temperature of interest. Both Vycor and quartz capsules were used. In general, the final equilibrium nitrogen content for each Fe-Ni alloy was approached from both higher and lower nitrogen levels. The criterion for establishing that equilibrium was attained was that the final nitrogen content for each Fe-Ni alloy was the same irrespective of the initial level. A schematic drawing of the sample configuration in a capsule is shown in Fig. 1. The samples were arranged so that there was a minimum of physical contact. The samples were also dusted with a fine, high purity alumina powder to help prevent sticking. Several different types of furnaces were used in this study. In each case, a thermocouple was placed immediately adjacent to the capsule during equilibration and the temperature was controlled to within *4?C of that reported. At each equilibration temperature, the following times were found to be more than sufficient to attain equilibrium: 600°C-250 hr, 900°C-150 hr, 1000°C-150 hr, and 1200°C-50 hr. After equilibration the capsules were quenched in water and the nitrogen contents of the specimens determined by a Strohlein analyzer. Analyses of samples after equilibration at 1000" and 1200°C showed no silicon pickup from the silica capsules. RESULTS AND DISCUSSION Transfer Mechanism. The mechanism by which nitrogen was transferred among specimens in an initially hydrogen flushed and partially evacuated capsule equilibrated at 1000°C was investigated. After equilibration the gas in the capsule was collected over water and an estimate of the pressure at temperature

Jan 1, 1970

By Carl Zapffe

A Rise in less than ten years from obscurity into great prominence economically, tersely summarizes the history and status of the Cuyuna manganiferous iron ores. The Cuyuna district produces and ships mostly high-phosphorus iron ore, but the annual production of manganiferous iron ore is increasing rapidly and productions from individual mines are becoming more regular and more dependable as to grades and tonnages. This ore bids fair to become, shortly, the principal product of the district and is responsible for its present economic prominence. The iron ores of the district have been described, by the author and others, in many publications and will not be discussed here. Lately the manganiferous iron ores have been given some attention, but the range and variations of chemical composition of the ores, the principal physical characteristics of the ores and their deposits, the relative importance of the different ores and their possibilities in future developments, and the life of the respective reserves have not been discussed. It is impossible to give all of this information with the positiveness necessary for it to constitute a reliable guide for investment or even for future mine development. Each property and each party presents a special case and deserves critical consideration. We are dealing with special ores and always with a set of new conditions. Sufficient information of a general nature can be given, however, to indicate the reason for and the trend of the presently augmented developments in the district. In a great thickness of a big variety of sedimentary rocks, probably of Upper Huronion age, prevailingly of green, schistose phases of slaty and volcanic material intricately intermixed, lies a thin bed containing lenses of iron-bear ing formation. These lenses occur singly or in groups, thus causing the variation in the thickness of the formation; or they are separated at their ends and give rise to discontinuity or they overlap and display continuity with lateral offsets. Intense folding has added to the complications.

Jan 1, 1925

By Rex B. McLellan, W. A. Oates, William W. Dunn

Vapor transport experiments have been carried out in order to determine the saturation solubility of carbon in cobalt and nickel with respect to graphite over a large temperature range. Some of the uncertainty existing in the thermodynamics of these systems has been removed and accurate estimates of the heat and entropy of solution of carbon in nickel and cobalt have been deduced. The relatitle partial entropies of carbon are considered to be predominantly vibrational in origin. ALTHOUGH the thermodynamic properties of solid solutions of carbon in cobalt and in nickel have been investigated previously, the results of these investigations show a marked lack of agreement amongst themselves. In this investigation simple vapor transport experiments have been undertaken in order to measure the temperature variation of the saturation solubility of carbon in nickel and cobalt with the object of removing to some degree the uncertainties in the thermodynamics of these systems. In the case of the C-Co system, early measurements of the saturation solubility of graphite in Co show results at the same temperature differing by almost an order of magnitude.1-5 Recently Schenck, Frohberg, and Jaspert6 measured the equilibrium between CH4-H2 mixtures and C-Co solid solutions at five temperatures ranging from 850° to 1050°C. Their values of the activity of carbon in the solid solution, deduced from a knowledge of the chemical potential of carbon atoms in the gas, varies linearly with composition at each temperature and the authors concluded that the solutions were Henryan. The saturation solubilities deduced from Schenck, Frohberg, and Jaspert&apos;s measurements are in good agreement with the solubility determined at 1000°C by Rao and Nicholson7 and the value at 1000°C deduced from the measurements of smith8 on the equilibrium between CO/CO2 mixtures and C-Co solutions. The object of this investigation was to check the results of Schenck, Frohberg, and Jaspert and also to extend the range of solubility data to higher temperatures. In the case of the C-Ni system, there is fairly good agreement between the values given by schaefer9 for the saturation solubility of carbon C, in nickel, the value given at 1000°C by Rao and Nicholson,7 and that deduced from Smith&apos;s8 measurements of the equilibrium between C-Ni solutions and CO/CO2 mixtures at 1000°C. The values of C, deduced from Schenck, Frohberg, and Jaspert&apos;s6 measurements of the carbon activity in nickel are also in fairly good agreement. However, there is a large discrepancy between the above set of measurements and those of Lander, Kern, and Beach," who measured the carbon solubility of nickel in equilibrium with graphite by depositing an excess of graphite on the surface of Ni-foils from a gaseous mixture and subsequently diffusing in the carbon. These results are considerably higher than those mentioned above. The determinations6 of carbon activity a, in nickel from the CH4-H2 equilibrium showed that at all the temperatures investigated, the ac-values varied linearly with concentration up to about a, = 0.6 and then began to increase with concentration much more rapidly. On the basis of auxiliary experiments in which C-Ni solutions were equilibrated with graphite, Schenck, Frohberg, and Jaspert concluded that their CH4-H2 solid equilibrations at high values of a, were spurious and a, behaved linearly with composition up to the saturation limit (a, = 1). The short linear extrapolations of Schenck, Frohberg, and Jaspert&apos;s a, data yield values of C, in good agreement with those of Lander, Kern, and Beach." The solubility data for nickel discussed here is presented in Fig. 1 in the form of plots of ln[Cc/(l - 2cc)] vs 1/T. The discrepancies mentioned are clearly seen. In this investigation a vapor transport method is used to measure C, over as wide a temperature range

Jan 1, 1969

By R. L. Rickett, W. C. Leslie

The influence of deoxidation practice, prior thermal history, and aging time and temperature on the strain-aging behavior of low-carbon open-hearth steels was investigated. The criterion of aging employed was the increase in yield strength in the tensile test, after straining and aging. Composition, prior heat treatment, and aging conditions were all found to be important in governing the strain-aging characteristics of these steels. THAT deoxidation changes the strain-aging propensities of low-carbon steels has been known for a long time, but there has been little agreement, and even contradiction, between results obtained by different investigators and between results obtained in the laboratory and in the mill. This investigation was begun in the hope that some of the uncertainties connected with the strain aging of commercial steels could be eliminated. In considering this problem, it was necessary to define strain aging and to examine the methods used to measure this property. Strain aging can be defined as the changes in properties of a metal or alloy with time, after cold working. The rate at which these changes occur increases as the temperature is raised above atmospheric. The requisite plastic strain is the principal distinction between strain aging and quench aging, the latter being due to precipitation from supersaturated solid solution. Strain aging is also characterized by rapid attainment of maximum hardness at high aging temperatures and lack of softening (overaging) at low aging temperatures. Several possible criteria of strain aging have been listed by Sachsl and by Davenport and Bain.&apos; Because changes in mechanical properties are the most easily measured and the most commonly used, consideration of methods to be used in this investigation was confined to three tests: tensile, notch-impact, and hardness. Hardness tests are the most economical and easiest to perform, but produce only one measure of strain aging. Also, as pointed out by Felmly, Hartbower, and Pellini,³ hardness changes due to aging are not pronounced for steels containing more than 0.15 pct C. Notch-impact tests require careful preparation of large numbers of specimens. Above and below the transition temperature the test lacks sensitivity; furthermore, it is extremely difficult to impart a uniform strain to the specimens, followed quickly by aging and final testing; machining must generally take place after straining. For these reasons, the tensile test was selected for use. Although this test requires a considerable expenditure of time, labor, and money in preparation of the specimens and performance of the test, more information can be gained than from any other single mechanical test, information which includes upper and lower yield points, yield-point elongation, tensile strength, strain-hardening exponent, reduction of area, and elongation. Low and Gensamer&apos; and Schwartzbart and Low5 lso used the tensile test, taking the increase in flow stress after straining in tension and aging as a measure of strain aging. In our work, as in theirs, each specimen was strained an arbitrary amount, sufficient to pass through the

Jan 1, 1954

By J. P. Van Kleunen

9.3-1. Introduction. The demands of industry for handling materials at higher rates and at reduced costs have had a very significant effect on belt conveyor technology. Although the general appearance of the belt conveyor today is essentially the same as it has been for the past several decades, the similarity ends there. Each component comprising the conveyor system has been continuously improved through design and materials technology to enable present conveyor systems to operate at ever-increasing rates and reliability. For example, twenty years ago the strongest commercially available, fabric-reinforced conveyor belting had a tension rating of 50 lb per ply-in. Currently, fabric-reinforced belts are available with ratings of 350 lb per ply-in. and steel cable reinforced belting is available with tension ratings of 3000 lb per in. of belt width (3). These technological advances have therefore enabled the belt conveyor to not only attain acceptance as a preferred method for in-plant movement of bulk materials, but also to be used for long distance transportation of bulk materials, particularly in areas of adverse terrain. The information contained in this chapter is intended to assist the reader to make basic decisions regarding the use and application of a conveyor system. The design of an overland conveyor transportation system or an in-plant process conveyor is accordingly beyond the scope of this article. Many comprehensive technical works covering the design of a belt conveyor are currently available from the manufacturers of materials handling equipment (6, 7, 9, 11). The design handbook published by the Conveyor Equipment Manufacturers Association is particularly recommended (2). 9.3-2. Conveyor Capacities. One of the most important factors in determining the proper size of a conveyor system is the rate at which material must be handled. Although tables and charts are available to the conveyor designer to assist him in his selection of conveyor components, only the

Jan 1, 1968

By R. C. Ferguson, Harlowe Hardinge

Laboratory and plant data covering 12 different operations show that lower than "standard" ball mill speeds increase grinding efficiency. In the case of high pulp-level mills, the gain is so great that the increase in capital cost of the larger lower speed mill will pay for itself in less than a year&apos;s time. THE object of this paper is to show the economic advantage of operating ball mills at relatively slow speeds. Although many operators know that grinding costs are reduced by operating mills at low speeds, they seldom do so for a variety of reasons. When capital is limited, first cost is of primary importance, and installation of the less costly, highspeed mill is favored. When materials are in short supply, as during a war period, capacity rather than economy is the primary consideration. Existing mills are then speeded up to provide the desired increase in capacity, and new mills are purchased without consideration of maximum grinding efficiency. When the mill speed is increased to secure more production, the increase in grinding costs is often obscured by the total benefit derived from the additional output. This increase in grinding cost is seldom recognized as being sufficient to be worth correcting. For these reasons one may be lead to the erroneous conclusion that slow-speed operation is only occasionally applicable. The effect of mill speed on grinding efficiency has been studied in laboratory tests."! The results of some of these tests are given in tables I and I1 and fig. 1. In these tabulations, batch tests using ore charges of 125 to 200 lb were considered comparable to high pulp-level operation and charges of 50 to 100 lb comparable to low pulp-level operation. For the high pulp-level operation, these tests indicate the existence of a maximum in efficiency for operation at a speed of 50 pct of critical, both for the soft (dolomite) and hard (chert) ore. In low pulp-level operation, a decrease in speed increases the efficiency of grinding dolomite; no maximum of efficiency appears in the range of speeds tested. The results with chert were inconclusive. If the performance of large mills is indicated

Jan 1, 1951

By Harlowe Hardinge, R. C. Ferguson

Laboratory and plant data covering 12 different operations show that lower than "standard" ball mill speeds increase grinding efficiency. In the case of high pulp-level mills, the gain is so great that the increase in capital cost of the larger lower speed mill will pay for itself in less than a year&apos;s time. THE object of this paper is to show the economic advantage of operating ball mills at relatively slow speeds. Although many operators know that grinding costs are reduced by operating mills at low speeds, they seldom do so for a variety of reasons. When capital is limited, first cost is of primary importance, and installation of the less costly, highspeed mill is favored. When materials are in short supply, as during a war period, capacity rather than economy is the primary consideration. Existing mills are then speeded up to provide the desired increase in capacity, and new mills are purchased without consideration of maximum grinding efficiency. When the mill speed is increased to secure more production, the increase in grinding costs is often obscured by the total benefit derived from the additional output. This increase in grinding cost is seldom recognized as being sufficient to be worth correcting. For these reasons one may be lead to the erroneous conclusion that slow-speed operation is only occasionally applicable. The effect of mill speed on grinding efficiency has been studied in laboratory tests."! The results of some of these tests are given in tables I and I1 and fig. 1. In these tabulations, batch tests using ore charges of 125 to 200 lb were considered comparable to high pulp-level operation and charges of 50 to 100 lb comparable to low pulp-level operation. For the high pulp-level operation, these tests indicate the existence of a maximum in efficiency for operation at a speed of 50 pct of critical, both for the soft (dolomite) and hard (chert) ore. In low pulp-level operation, a decrease in speed increases the efficiency of grinding dolomite; no maximum of efficiency appears in the range of speeds tested. The results with chert were inconclusive. If the performance of large mills is indicated

Jan 1, 1951

By P. Chiotti, G. R. Kilp

Thermal, metallographic, vapor pressure, and X-ray data were obtained to establish the phase diagram for the zinc-zzrconiz~m system. Five compounds corresponding to the stoi-chiometric formulas ZrZn, ZrZn,, ZrZn,, ZrZn,, and ZrZn14 were observed. All these compounds, with the exception of ZrZn2, which melts congruently at 1180°C under constrained zinc-vapor conditions, undergo pexitectic reactians. The temperature at which the zinc vapor pressure is I atm for a series of alloys was determined from vapor-pressure measurements. The data obtained are summarized in the construction of a I-atm-pressure phase diagram and a phase diagram corresponding to a pressure of less than 10 atm. THE purpose of this investigation was to establish the phase diagram for the zinc-zirconium system. Thermal, metallographic, vapor pressure, and X-ray data were employed in determining the phase regions. Partial investigations of this system have been conducted by Gebhardt1 and Carlson and Borders.&apos; Carlson and Borders studied the high-zirconium region and established the existence of a eutectic at 69 wt pct Zr with a melting point of 1015°C. The terminal phases of the eutectic horizontal were shown to be an intermetallic compound ZrZn and a solid solution of ß zirconium containing 21 wt pct Zn. The ß solid solution decomposes into ZrZn and a zirconium at 750°C. The eutectoid composition is given as 15 wt pct Zn, and the solubility of zinc in a zirconium at temperatures below 750°C is indicated to be negligible. Gebhardt studied the zinc-rich region and observed a lowering of the melting point of zinc from 419.5" to 416°C and temperature horizontals at 545" and970°C. Some preliminary observations by Chiotti, Ratliff, and Kilp were reported by Hayes.2 pietrokowsky3 has reported the compound ZrZn2 to have a cubic MgCu2 structure with ao = 7.396A. MATERIALS AND EXPERIMENTAL PROCEDURES The metals employed in the preparation of alloys were Bunker Hill slab zinc or Baker analyzed reagent granulated zinc, both 99.99 pct pure and hafnium-free iodide-process crystal bar zirconium obtained from the Westinghouse Electric Corp. The zirconium contained 200 ppm Fe, 200 ppm Si, 100 ppm C, and minor amounts of other impurities. The zirconium was milled or machined into thin chips or shavings. These were cleaned with a nitric-hydrofluoric acid solution, rinsed with water, and acetone, and dried just prior to their use in alloy preparation. The granulated zinc was similarly cleaned using dilute nitric or hydrochloric acid. Weighed quantities of these materials, 20 to 30 g total, were mixed and pressed at 20,000 to 70,000 psi to give relatively dense compacts. During the early part of this investigation the pressed compacts were placed in MgO-15 wt pct MgF, crucibles which were then sealed inside of quartz ampules. The compacts were given various prolonged heat treatments prior to their use for thermal analyses, or vapor-pressure measurements. Because of expansion of the compacts and the relatively high zinc vapor pressure it was difficult to heat to the melting temperatures of the alloys without failure of the quartz ampules. Homogenization at temperatures below the melting temperature gave brittle, porous alloys unsuitable for metallographic examination. It was also difficult to prevent condensation and segregation of zinc on the colder parts of the quartz ampules during heating and cooling operations. These problems were eliminated to a great extent by the use of tantalum crucibles. Tantalum proved to be a satisfactory container with little or no reaction between the alloys and the tantalum. Small tantalum thermocouple wells were successfully welded in the bottom of these crucibles. Pressed compacts were sealed inside the tantalum crucibles by welding on preformed caps under an argon atmosphere. Heat treating and differential thermal analysis were combined into a single operation. The experimental sample assembly is shown in Fig. 1. This assembly was enclosed inside a stainless-steel tube heating chamber which could be evacuated and filled with an inert gas. The thermocouple leads were brought out of the heating chamber between two rubber gaskets used to provide a vacuum seal for the water-cooled head. Most of the compounds in this system undergo peritectic decomposition. After heating above the temperature of a particular peritectic horizontal the sample was cooled to just below the peritectic temperature and held at temperature for several hours. The sample was then reheated through the peritectic temperature and the size of the thermal arrest, if still present, compared with the one previously obtained. If the thermal arrest was not characteristic for the alloy composition being investigated its magnitude diminished and repeated cycling and annealing eventually eliminated it. The peritectic thermal arrests characteristic of a particular composition were established in this manner.

Jan 1, 1960

By Edward H. Robie

EIGHT years ago in this department we had a column on the daiquiri cocktail, which, as we pointed out at that time, was invented by mining engineers. Since then we have said little or nothing about alcoholic drinks, but having set the precedent perhaps we may now pass along a little information about martinis. We have observed that as an aperitif the martini has become increasingly popular with men, so much so that we always feel a bit peculiar if we order something else. And the call is not for just a martini either; it must be a dry martini, and some of our friends are extremely particular on this point. The matter has achieved such importance that The New York Times devoted half a page to it a few Sundays back. Several recipes are given which may be useful to some of our members when entertaining visitors from this part of the country: The standard martini is said to be half gin, half Italian vermouth, two dashes orange bitters, and a pickled onion and twist of lemon peel. This progresses to the very dry martini, which calls for five parts gin and one part vermouth with an onion, olive, or lemon peel. Several alternatives are offered for the manufacture of the very, very dry martini. One is to pour a little vermouth into the mixing glass and pour it out again before mixing gin and ice. A second way is to put the ice in a sieve, hold it over the sink, and pour a little vermouth over it; then put the ice in the mixing glass. A third is to let the draft from an electric fan blow across an open vermouth bottle toward the mixing glass. Then the ultimate is the awfully dry martini, obtained by setting the vermouth bottle next to the mixing glass and turning the bottle slowly so that the label is exposed to the gin for perhaps a second. The Times notes that Mr. Martini himself personally prefers vermouth and soda.

Jan 1, 1952

By Fulton Flick

THE micrography and macrography of aluminum and its alloys present certain difficulties. Many of the difficulties attendant on the micrography have been removed by methods developed during the past few years, notably those of E. H. Dix, Jr.1 The development of grain size in aluminum and its alloys may be equally troublesome, yet comparatively little detailed attention appears to have been given to it. Satisfactory reagents. are available for the development of such structures in ferrous and most non-ferrous metals, but those applied to aluminum and its alloys, i. e., alcoholic or aqueous solutions of sodium hydroxide or hydrofluoric acid are not entirely satisfactory. Hanson and Archbutt,2 in speaking of these two reagents, state that "These two reagents give fairly satisfactory results, but they sometimes produce badly tarnished surfaces from which the surface deposit is difficult to remove." It has been our experience that neither of these reagents is to be entirely relied on for developing structures suitable for study or photography. This means that when the etch fails to produce satisfactory results the, specimen must be repolished, through the 000-paper at least, and then etched with another reagent. This procedure entails a con¬siderable loss of time, and the final results may not be all that might be desired. However, the reagent to be described, although not a panacea for all etching troubles, has improved results so markedly that it is felt that it is worth offering as a grain-size etch generally applicable to aluminum and aluminum alloys. Czochralski3 in 1915 mentioned the application of a solution of 10 to 20 c. c. concentrated hydrofluoric acid in 100 c.c. absolute alcohol, etching in this reagent being followed by dipping in concentrated hydrochloric-acid solution.

Jan 2, 1925

By Frederick Laist

0. C. RALSTON, Salt Lake City, Utah.-I have merely glanced over this paper, consequently, I am hardly in a position to discuss it intelligently. There is one thing, however, that is of interest, that is, the claim that the oil mixture which they have chosen is the best adapted to the work at hand. I would like to ask Mr. Mathewson if they still feel that that is the case-if that really does give the best grade of concentration and the best extraction for the same money, compared to any particular oil mixture which they could get. E. P. MATHEWSON, Anaconda, Mont.-We are still using that mixture, and we consider it the most economical mixture used. DAVID COLE, El Paso, Texas.-I would like to ask Mr. Ralston if there are some other mixtures that would be better? E. P. MATHEWSON.-We are open to suggestions. 0. C. RALSTON.-My own paper on oils* calls attention to the fact that certain hardwood oils, especially the tars, are now being burned or wasted. A great deal of hardwood tar is available as low as 4 or 5 c. per gallon, that being its value as fuel under the boilers. As a matter of fact, a great deal of testing has been done with only the commercial products that are as a usual ride sold on the market. Very little hardwood tar is sold on the market. In asking a great many people who have tested flotation oils, I have not heard hardwood tar mentioned very often. I think I would add to that that the hardwood tars can probably be bought in quantity comparable with the sludge acid at Anaconda, and. should contain a greater proportion of the frothing constituent, and at a price fairly commensurate with what they pay for the sludge acid. E. P. MATHEWSON.-I would like to make a correction in one statement I made that there has been no change made in the mixture. This change has been made: We found that the amount of wood creosote in treating the sand from tables was extremely small, and we tried some experiments on a large scale, dropping it out and using simply the sludge acid and sulphuric acid. We found that this gave practically as good results as wood creosote. We use wood creosote in treating the slimes. We find it necessary in that operation. DAVID COLE.-I would like to ask, what is sludge acid?

Jan 10, 1916

The income of the Institute is derived from dues, subscriptions to MINING AND METALLURGY sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing. committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization and at a minimum of expense. J. V. W. Reynders is chairman of the Endowment Committee.

Jan 1, 1929