Search Documents

By G. G. Gunther, C. L. Boeke

DISCUSSION I. M. Symonds, (Cia. Minera de Penoles, Monterrey, N. L., Mexico)—Messrs. Boeke and Gunther have written most interesting papers describing their zinc de-leading operations. Mr. Gunther was kind enough to show me his operation last fall. Aside from the excellent results, I was most impressed by the ease of control. I had expected a difficult operation requiring careful control and supervision, but found one requiring little attention. The only disappointing fact of the separation is the poor copper recovery in the concentrate of the delead-ing float. The final zinc concentrate still has about 3 pct chalcopyrite, assuming the copper is chalcopyrite, and adversely affects the zinc grade. If the copper mineral is free, the poor recovery is probably due to the high cyanide concentration. Fortunately, about 75 pct of the copper is recovered before the pulp goes to the zinc circuit. Mr. Gunther's remarks about proper cyanide to zinc sulphate ratios cannot be overemphasized. Although our experience has been confined mostly to the conventional lead-zinc separation, we have found these ratios most important, and more important in the mill than in the laboratory. The laboratory appears to give optimum results over a wider range of reagent control than the mill, especially in regard to the effect of cyanide. In handling relatively high grade ores in the mill we usually find that ratios of cyanide to zinc sulphate of 1 to 10 or 20 or higher work best. Where there is a substantial amount of chalcopyrite present it has been noted that cyanide in the range of 0.02 to 0.10 lb per ton of ore is often beneficial in zinc rejection and possibly in copper recovery in the lead concentrate, while larger amounts, say 0.20 to 0.25 lb per ton, will float more zinc and cause a serious rejection of chalcopyrite. On an ore with 15 to 20 pct zinc content we have had to use 0.8 to 1.2 pounds of zinc sulphate per ton of ore with the above cyanide to obtain optimum results. Some time ago we made a laboratory study following Parral and Santa Barbara practice on an ore which had never a very satisfactory rejection of zinc in the lead concentrate. The results were not encouraging and a mill test was not run. Since then the study has been reopened using in the laboratory fresh zinc concentrate from the mill instead of one made in the laboratory. A reasonably clean lead float from the zinc concentrate was obtained. It has been checked several times and each time the zinc concentrate made in the mill responds and the one made in the labora-

Jan 1, 1953

By G. G. Gunther, C. L. Boeke

DISCUSSION I. M. Symonds, (Cia. Minera de Penoles, Monterrey, N. L., Mexico)—Messrs. Boeke and Gunther have written most interesting papers describing their zinc de-leading operations. Mr. Gunther was kind enough to show me his operation last fall. Aside from the excellent results, I was most impressed by the ease of control. I had expected a difficult operation requiring careful control and supervision, but found one requiring little attention. The only disappointing fact of the separation is the poor copper recovery in the concentrate of the delead-ing float. The final zinc concentrate still has about 3 pct chalcopyrite, assuming the copper is chalcopyrite, and adversely affects the zinc grade. If the copper mineral is free, the poor recovery is probably due to the high cyanide concentration. Fortunately, about 75 pct of the copper is recovered before the pulp goes to the zinc circuit. Mr. Gunther's remarks about proper cyanide to zinc sulphate ratios cannot be overemphasized. Although our experience has been confined mostly to the conventional lead-zinc separation, we have found these ratios most important, and more important in the mill than in the laboratory. The laboratory appears to give optimum results over a wider range of reagent control than the mill, especially in regard to the effect of cyanide. In handling relatively high grade ores in the mill we usually find that ratios of cyanide to zinc sulphate of 1 to 10 or 20 or higher work best. Where there is a substantial amount of chalcopyrite present it has been noted that cyanide in the range of 0.02 to 0.10 lb per ton of ore is often beneficial in zinc rejection and possibly in copper recovery in the lead concentrate, while larger amounts, say 0.20 to 0.25 lb per ton, will float more zinc and cause a serious rejection of chalcopyrite. On an ore with 15 to 20 pct zinc content we have had to use 0.8 to 1.2 pounds of zinc sulphate per ton of ore with the above cyanide to obtain optimum results. Some time ago we made a laboratory study following Parral and Santa Barbara practice on an ore which had never a very satisfactory rejection of zinc in the lead concentrate. The results were not encouraging and a mill test was not run. Since then the study has been reopened using in the laboratory fresh zinc concentrate from the mill instead of one made in the laboratory. A reasonably clean lead float from the zinc concentrate was obtained. It has been checked several times and each time the zinc concentrate made in the mill responds and the one made in the labora-

Jan 1, 1953

By Charles M. Romanowitz

The motivation for the art of dredging for placer mining can be compared in a slight degree to the spread of civilization which started in the Near East and spread both east and west. Dredging started with the "bag and spoon" dredge in the lowlands of Europe reportedly about 1565, went southeast to New Zealand where designs were developed for a bucket-line mining dredge known as the New Zealand type, and westward to the eastern United States where a dredge was developed and used exclusively for excavating. Then it moved to Montana, where it was first used for mining in 1895. The New Zealand-type dredge was imported into California in 1898 (Fig. 1) and was followed shortly by the Montana design. As today, these early dredges were equipped with continuous bucket- line chains, a treatment plant, and a means of waste disposal mounted on a wooden hull. Both types of dredges are complete mining units: they dig the formation, transport the dug materials, and concentrate the valuable ore. After sizing, the fines containing the ore are passed by gravity to the treatment unit, while the barren materials are discharged overboard. By digging the materials to be treated at the bow and depositing all the waste, at the stern, the dredges automatically advance to new reserves without presenting any transportation problems. The main differences between the two types are in the method of holding the dredge in the digging position and in the disposal of the tailings to the rear. The New Zealand type (Fig. 2) uses the headline system with a bow anchor for holding the dredge in the digging position and long tailing flumes or short stackers off the stern for disposal of the barren materials. The California type (Fig. 3) uses box girder spuds projecting into the ground in a vertical position at the stern of the

Jan 1, 1969

By P. Barnes

THE complete and accurate filtration of water (if the word ,accurate may be thus used) for the feeding of boilers, and for many similar industrial purposes, although somewhat practiced both at home and abroad, has been by no means common. Even if the exact line cannot be defined at which filtration begins to be called for, and will be found profitable, it is certain that in a large number of cases it may be employed with real advantage in the economy of fuel, and also in. the greater durability of the boiler or other form of apparatus in

Jan 1, 1882

By C. A. Heiland

THE Eötvös torsion balance permits the measurement of certain second derivatives of the gravity-potential, which are known as the gradients of gravity and the curvature values for an, equipotential plane of gravity. These quantities are influenced on level ground by the configuration of the masses underneath. Hence, the torsion balance has gained great importance for the location of geological structures and thus indirectly for the discovery of oil and other mineral deposits. If the ground is not level, however, the measurements become more difficult, because the superficial mass-irregularities also produce more or less considerable disturbances. It is necessary, therefore, to determine the shape of the surrounding topography by leveling as well as by consulting topographic maps and to compute its influence upon the torsion balance. The correction thus determined is called, in general, the topographic correction; it is composed of two constituents, the terrain correction and the cartographic correction. The terrain correction would be that part of the topographic correction as derived from the direct leveling of the area surrounding the station, whereas the data for the computation of the cartographic correction are obtained from a topographic map, usually beginning with a radius of 100 meters, as under most circumstances it is difficult to level along a larger concentric circle about the station.

Jan 1, 1928

By C. A. Heiland

THE Eötvös torsion balance permits the measurement of certain second derivatives of the gravity-potential, which are known as the gradients of gravity and the curvature values for an equipotential plane of gravity. These quantities are influenced on level ground by the configuration of the masses underneath. Hence, the torsion balance has gained great importance for the location of geological structures and thus indirectly for the discovery of oil and other mineral deposits. If the ground is not level, however, the measurements become more difficult, because the superficial mass-irregularities also produce more or less considerable disturbances. It is necessary, therefore, to determine the shape of the surrounding topography by leveling as well as by consulting topographic maps and to compute its influence upon the torsion balance. The correction thus determined is called, in general, the topographic correction; it is composed of two constituents, the terrain correction and the cartographic correction. The terrain correction would be that part of the topographic correction as derived from the direct leveling of the area surrounding the station; whereas the data for the computation of the cartographic correction are obtained from a topographic map, usually beginning with a radius of 100 meters, as under most circumstances it is difficult to level along a larger concentric circle about the station.

Jan 1, 1928

By Maurice Ewing

THE purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data sum-marized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the oppor-tunity for checking results so thoroughly is given. In the second place, the fact that recent commentators1,2,3 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1922, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By A. F. Lucas

EACH day, the fact becomes more evident that the ever-growing demand for oil is farther outstripping production, regardless of the increase in output throughout the past twenty years. The development of known oil fields and the prospecting for new ones along present lines are not resulting, in, and cannot bring forth, supplies large enough adequately to meet the oil needs of the country. The usual methods of prospecting-for new supplies are insufficient to meet the exigencies of the situation which threatens, in the not distant future, to reach a critical stage. Were it not that within the last two years new and prolific oil fields have been discovered in northern Louisiana, central Texas, and California, this crisis would undoubtedly be now at our door. Stocks are being exhausted in spite of the rapid growth of imports. The time is therefore fast approaching when some radical departures must be made in the method of prospecting and developing old and new fields in order to increase our oil supplies. Methods and chances, that have seemed unwarranted will not only be given serious consideration, but, according to the results promised, will be put to the test. Meanwhile, however, nearly all the oil fields are responding to the stimulus of higher prices, whereby enormously growing capital is attracted to this important industry, both here and abroad; the increase in our petroleum production at the present time is due to this circumstance. Yet, although a most active search is being made for possible sources of additional supply, one section of our country is not yielding the results that, in my opinion, it is capable of producing: I allude to the coastal dome belt of Texas, Louisiana, and Mexico. The United States Geological Survey has estimated that three-fourths of a billion barrels are available in the ground in the Coastal Plain of the two states just mentioned. Numerous papers have been written on the subject of the salt domes of the Coastal Plain and more or less attractive theories have been advocated by leading geologists to account for their origin and the presence of the oil, sulfur, and salt associated in them. However, owing in part to the generally monotonously level country in which the coastal

Jan 9, 1920

By G. Derge, W. Peifer, J. H. Richards

INTRODUCTION A WIDE variety of metallurgical defects in steel have commonly been attributed to the presence of excessive amounts of hydrogen. These defects include flakes in rails and forgings, cracks in welds, and blisters in enameled ware. They have been related to hydrogen largely by circumstantial evidence because the proper sampling and analysis of steel for hydrogen has been known to be difficult and because no general agreement has existed with regard to the relative suitability and accuracy of available methods. The need for a direct approach to these problems has been widely recognized. This general situation has been well described in the publications of the British Committee on the Heterogeneity of Steel Ingots,1 and current approaches to the problem were reviewed in a recent symposium of the AIME.12 The plans described by the present authors at that meeting have now matured satisfactorily and will form the basis of this paper. The principle object of this paper will be to describe the methods of sampling and analysis which have been developed and to illustrate the usefulness and limitations of these methods by citing their application to a specific problem. The first problem selected for investigation was the behavior of hydrogen in rail steel. This was chosen because the occurrence of shatter cracks in rails has received a great deal of study over a long period of time. The defect can be controlled by the expensive procedure of slow cooling. However, it may be hoped that a better understanding of the factors influencing the hydrogen content of rails will lead to a more efficient control of this problem. Rails provide a good starting point for a more general study of hydrogen in steel because they provide a cross section large enough to develop cracks, yet small enough for convenient handling and sampling. Rails were also selected because they are made from plain carbon steel and it was felt that the initial work should not be complicated by the effects introduced by alloying elements. The considerations which determined the original planning of this study should be reviewed. The inherently complex nature of most hydrogen problems requires that a large amount of data must be collected for any particular case. This in turn means that any analytical procedure should be as rapid and simple as possible. The same objective of speed is indicated by the fact that it may finally become desirable to use hydrogen analysis in process control. It is also known that hydrogen is highly fugitive and that any procedure which facilitates early analysis of the sample without prolonged or irregular storage has distinct advantages. The most important previously reported methods of analysis may be classified into three general groups: (I) Vacuum fusion. (2) Vacuum extraction (without melting). (3) Total combustion.

Jan 1, 1948

By Charles Will Wright

The present struggle for economic and industrial supremacy by the Communist world is against the United States, its main target, and the other Free World nations. The basis of industrial power is minerals, so the Communist nations are building up mineral production within their borders, often regardless of costs, and are acquiring quantities of mineral products from Free World countries for future use. They are contracting for additional supplies and advancing funds for the development of these quantities. A number of the less developed mineral producing countries of the Free World are being infiltrated by Communists and Communistic influence. This situation is well known, but as yet little has been done to oppose these activities or to awaken the public to their seriousness. The Communist countries are still far behind the Free World Nations in production of many essential minerals. But, shortages are being made up from Free World nations in exchange for petroleum, manganese ore, chromite and other products. Restrictions on shipments of strategic materials to Communist countries have not been maintained.

Jan 1, 1964

By George H. K. Schenck

The investment analysis methods that are most generally accepted in the mineral industries in the mid-80's are presented along with their advantages and disadvantages. Also covered are current widely-used practices for introducing the uncertain nature of most of the important variables in an investment analysis, which is contrasted to the former dominance of deterministic analysis. Finally, the discussion turns to current practice for handling the two critical areas: cost of capital and inflation. The advice contained is reinforced with data from a survey of current practices in the petroleum industry.

Jan 1, 1985

By James J. Olson, Richard A. Dick

Blasting practices have shown a recent trend toward larger blastholes and larger burdens and spacings, although some operators, after reconsidering the situation have gone back to smaller blasthole sizes. The greater pull-down capabilities of larger drill rigs and the greater bearing strength of large diameter drill bits give penetration rates for large diameter blastholes approaching, and sometimes exceeding, penetration rates for smaller holes. In practically all cases, large diameter holes can be drilled more quickly and cheaply, based on volume of hole, than small diameter holes. The industry's shift to dry blasting agents and slurries, products which perform more dependably and efficiently in larger diameters, gives an additional advantage to larger boreholes.

Jan 3, 1972

By George Smith

TWELVE years ago, the Director of the United States Geological Survey addressed to the Secretary of the Interior a letter calling attention to the government's need for liquid fuel for naval use and pointing out that the rate of increase in demand was more rapid than the increase in production.1 This letter, in a way, inaugurated the policy of public oil-land withdrawals, which was well founded in its primary purpose of protecting the oil industry and highly desirable in its immediate effect of checking the over-development of that day in California. Unfortunately, however, through delays in legislation, this policy may be regarded now as having outlived both its intent and its usefulness. In 1908, the country's production of oil was 178,500,000 bbl., and there was a surplus above consumption of more than 20,000,000 bbl. available to go into storage.: In 1918, 10 years later, the oil wells of the United States yielded 356,000,000 bbl.-nearly twice the yield of 1908-but to meet the demands of the increased consumption more than 24,000,000 bbl. had to be drawn from storage. Nor is this all of the brief comparison. In 1918, our excess of imports over exports of crude petroleum was nearly 33,000,000 bbl. whereas in 1908 we exported 3,500,000 bbl., which was net, as we had not begun to import Mexican oil. In this period, the annual fuel-oil consumption of the railroads alone has increased from 16,871,000 to 36,714,000. bbl.; the annual gasoline production from 540,000,000 gal. to 3,500,000,000 gal. This record may be taken not only as justifying the earlier appeal for Federal action, but as warranting deliberate attention to the oil problem of today.

Jan 1, 1920

By W. H. Geis

THE following pages summarize the causes that led to the suggestion of unit operation of the Paloma field, the organization of committees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan.

Jan 1, 1942

By Derek C. Shelton

This chapter covers the preparation of specifications for a dry crushing and wet grinding comminution circuit.

Jan 1, 1982

By R. Kossowsky

USING etch-pit techniques, Johnston and Gilman' have shown that the stress dependence of dislocation velocity can be represented by the expression where r, is the dislocation velocity, a is the applied stress, and oa, is the stress to produce a unit velocity. Noble and Hul12 showed that the exponent m is strain-dependent and increases rapidly in the work-hardening region. This was explained by arguing that in the work-hardened material the applied stress required for any given velocity will be greater than in the annealed material by an amount equal to a back stress due to work hardening. schadler3 has stressed the importance of substructure as a possible source of error in dislocation velocity measurements, and took care to make velocity measurements in which dislocations moved such short distances that interactions with boundaries were avoided. schadler3 also pointed out that, if standard testing equipment is used, measurements of m from flow stress data could be seriously in error in materials with a high initial work-hardening rate. Noble and Hu112 have further argued that, due to the strain dependence of m , the extrapolation to zero strain4 to obtain the true value of m can be justified only in the preyield region. Microstrain experiments in high-purity iron5,6 have led to the conclusion that aiA (Ref. 5) (defined as the stress to first produce a permanent set of 10-6 in. per in.) and oflow are not controlled by the same deformation mechanism. It has been proposed5,6 that aA is governed by the lattice resistance to the motion of screw dislocations in a given slip plane and that oflow is controlled by the lattice resistance to a full-scale cross slip. The purpose of this note is to extend Noble and Hull's argument further and to show that measurements of m from flow stress data can be in error due to the rapid increase in stress in the microstrain region6 when stress is increased beyond aA. Double z-one-refined single crystals of molybdenum (with the (101)[ 111] slip system operating and a Schmidt factor of 0.475) were used in an experimen-

Jan 1, 1968

By Lester Uren

WITH the depletion of our older, and relatively shallow, oilfields and the necessity for securing new production from deeper horizons, much attention is being given to the improvement of oil-well pumps in order that they may function satisfactorily under the more difficult conditions imposed by increased depth. Until recently, practically all of the world's petroleum was secured from wells less than 3000 ft. deep, whereas horizons are now being explored to depths of from 5000 to 7000 ft. in some of the more prolific fields, and it seems probable that the greater part of the future supply must come from depths in excess of 3000 ft. While much of the early production in a new field is obtained by natural-flow methods, when the stimulus of high gas pressure fails, recourse must be had to some method of pumping. The perfection of a pump capable of economically and efficiently lifting oil from depths ranging from 3000 to 7000 ft. is therefore a matter of prime importance to the oil-producing industry. This paper is offered as an estimate of the present state of development of the oil-well plunger pump and as a review of the general principles involved in its operation in deep-well pumping. A design for a new type of oil-well pump embodying several novel features, is also described.

Jan 9, 1925

By John C. F. Randolph

(Read at the Amenia Meeting, October, 1877.) Tits establishment being now in full working order, it has seemed of considerable professional interest to collect together, in a concise form, the various points as to its plan, method of dressing, and equipment. The data contained in this paper have been largely drawn from the able paper of E. Kutscher, constructing engineer. of the works, contained in the Zeitschrift fur Berg-Hütten-und Salinenuesen im Preussischen Staate, 1873, supplemented by some personal memoranda made while the works were under construction and by memoranda on the works appearing in various German technical papers from their completion up to date. This is probably the largest dressing works in the world devoted to the beneficiation of argentiferous lead ores, and it is doubtful if any establishment for the concentration of mineral of any description can compare with it in size. As showing the final practice adopted in an old and very conservative mining region, in which the concentration of ores has been a matter of constant practice and experiment for a very long period, these works are of peculiar interest. The fact that the Clausthal ores strongly resemble a very large and abundant class of ores found in the United States has always attracted the attention of American mining engineers and mine owners to the methods employed in dressing and smelting them. The study of their methods of concentration of ores has, however, always been full of difficulty,

Jan 1, 1878

By AIME AIME

PLANS for the Semi-centennial Meeting have almost reached completion, although in any undertaking of such magnitude a few changes are always to be expected at the last moment. As worked out up to the time of going to press, the program of the meeting is shown below. The headquarters will be the Irem Temple, in Wilkes-Barre.

Jan 1, 1921

A piece of arid, strip-mined land in southeastern Washington recently yielded over 22 bushels of winter wheat per acre-without irrigation. The surprising crop yield is the product of an innovative reclamation technique-one of several methods now being developed as alternatives to traditional reclamation. Conventional reclamation methods are not always successful on strip-mined acreage in the arid West. Replanting native vegetation usually requires fertilizer and irrigation-both energy-intensive commodities in arid regions. Now, promising alternatives which rely solely on rainfall for irrigation are being offered by two research teams.

Jan 12, 1978