Search Documents

By William E. Brewster

Dating back some five years ago, various foundries made inquiries as to the probable total carbon content in a given specification and grade of pig iron. Up to that time we had no data, and except for a few occasional determinations of total carbon, no attempt had ever been made to set up routine determinations of total carbon. In fact, at that time, a cast analysis was considered sufficient, without examining at further length into possible variations of analysis between ladles of the same cast. In view of the various inquiries as to total carbon, we sampled all piles of all grades of pig iron, making complete analyses. Finding some variation in carbon content, we secured more samples and plotted the carbon content with respect to silicon in each grade of iron except for the higher phosphorus foundry iron, where it was necessary to divide the group into twenty-point phosphorus ranges. This is easily understood, owing to the falling off of carbon content with the increase in phosphorus content, silicon in each case being the same. In addition, these curves clearly demonstrate the lowering of the carbon content as the silicon is increased. In order to insure accuracy and reliable determinations the following method of sampling and analysis was employed: Two pigs selected from each end of the car, each car containing iron from one 50-ton ladle, are drilled with a 5/6-in. drill all the way through from top to bottom in the center of one section of the pig. The drillings are collected and transferred to an 80-mesh sieve; the portion passing through and the portion retained are placed in separate envelopes and labeled accordingly. The amount of sample in each envelope is weighed to obtain the proportionate amount of coarse and fine drillings, then a 1/2 factor weight of sample (1.3636 grams) made up of proportionate

Jan 1, 1936

THE Institute assembled in the Court-House, on Tuesday evening, May 22d, and was called to order by Vice-President E. B. Coxe. After announcement by the Local Committee of the programme for excursions, the Secretary read the following annual report of the Council The Council, in presenting to the Institute its annual report, has to record a most eventful year in the history of the Institute. Three meetings, as usual, have been held, two in Philadelphia and one in New York. At the Philadelphia meetings in June and October, there were present many distinguished foreign engineers, some of whom contributed communications to the Institute, and took part in its discussions. Sixty-seven papers have, in all, been presented to the Institute, which will be published in the fifth volume of Transactions. There has been an accession to the membership of 1 honorary member, 11 foreign members, and 162 members and associates; -8 have resigned, 6 have died, and 30 have been dropped from the roll, after due notification, for non-payment of dues. The membership now comprises 5 honorary members, 60 foreign members, and 644 members and associates, in all 699. As worthy of especial mention in the work of the year are the Discussions on Technical Education in connection with the American Society of Civil Engineers, and the report of the-International Committee appointed by the Institute to consider the nomenclature of iron and steel. The Discussions on Technical Education have been published in a separate volume, and comprise a valuable and suggestive collection of the views of practical engineers and educators. The report of the International Committee, composed of Messrs. Akerman, of Sweden; Bell, of England; Tunner, of Austria; Gruner, of France; Wedding, of Prussia; and Holley and Egleston, of the United States, has received the careful attention of engineers and metallurgists of all countries, and has met . with very general acceptance. Of the work of the Centennial Committee in Philadelphia the members are generally familiar, from personal experience, and from the detailed report of the committee at the last meeting of the Institute. But the record of the service rendered by this committee would he incomplete without mention of the numerous letters of thanks and formal expressions of obligations received by the Institute from individuals, societies, and governments abroad. The wise and generous spirit in which the work of the committee was planned, and the laborious and self-sacrificing manner in which it was carried out, call for emphatic expressions of thanks from the Institute. The gifts of Centennial exhibits to the Institute, largely as testimonials for services rendered, has necessitated the appointment of a Museum Committee for

Jan 1, 1878

By Ralph A. Sherman, E. R. Kaiser

The remarkable increase in the distribution of the small underfeed stoker for use in furnaces and boilers in small industrial plants, apartment houses and homes has brought producers and distributors of bituminous coal to consider the problem of which coals and which sizes are best suited to this market. Many papers have also appeared, mostly in the trade journals, discussing the problem of the combustion of various coals and various sizes of coal in small stokers. Much difference of opinion has been apparent in these articles; due often, it would appear, to a misunderstanding of the fundamentals of the process of combustion in the stoker fuel bed. During the past year and a half, a program of research has been conducted at Battelle Memorial Institute: (1) On the process of combustion in the fuel bed of the small stoker, sponsored by Battelle Memorial Institute, and (2) on the relation of the characteristics of bituminous coals to their performance on small underfeed stokers, sponsored by Bituminous Coal Research, Inc. As a result of this program of research, two publications have been made, one1 dealing with the problem of clinker formation, and the other2 with the relation of the size of the coal fed to the stoker hopper to that of the coal that reaches the retort to be burned. The experimental research on the relation of size to the performance of the coal is being actively continued. A publication of Bituminous Coal Research, Inc. presenting the data obtained on the performance of several sizes of four typical bituminous coals will appear shortly. Because of the early appearance of that publication, the present paper includes few numerical data. The purpose of this paper is to follow the coal from the hopper through the furnace with a discussion of the various actions that occur, in the hope that it will lead to a clearer understanding of the relation of the type of coal, the size of coal, and other characteristics, to the performance. The authors do not pretend to have obtained the answers to all the complex questions involved; many unanswered questions will be proposed on which future research work is planned.

Jan 1, 1938

By E. R. Kaiser, Ralph A. Sherman

The remarkable increase in the distribution of the small underfeed stoker for use in furnaces and boilers in small industrial plants, apartment houses and homes has brought producers and distributors of bituminous coal to consider the problem of which coals and which sizes are best suited to this market. Many papers have also appeared, mostly in the trade journals, discussing the problem of the combustion of various coals and various sizes of coal in small stokers. Much difference of opinion has been apparent in these articles; due often, it would appear, to a misunderstanding of the fundamentals of the process of combustion in the stoker fuel bed. During the past year and a half, a program of research has been conducted at Battelle Memorial Institute: (1) On the process of combustion in the fuel bed of the small stoker, sponsored by Battelle Memorial Institute, and (2) on the relation of the characteristics of bituminous coals to their performance on small underfeed stokers, sponsored by Bituminous Coal Research, Inc. As a result of this program of research, two publications have been made, one1 dealing with the problem of clinker formation, and the other2 with the relation of the size of the coal fed to the stoker hopper to that of the coal that reaches the retort to be burned. The experimental research on the relation of size to the performance of the coal is being actively continued. A publication of Bituminous Coal Research, Inc. presenting the data obtained on the performance of several sizes of four typical bituminous coals will appear shortly. Because of the early appearance of that publication, the present paper includes few numerical data. The purpose of this paper is to follow the coal from the hopper through the furnace with a discussion of the various actions that occur, in the hope that it will lead to a clearer understanding of the relation of the type of coal, the size of coal, and other characteristics, to the performance. The authors do not pretend to have obtained the answers to all the complex questions involved; many unanswered questions will be proposed on which future research work is planned.

Jan 1, 1938

By R. W. Kewish

The preparation of massive uranium metal containing very low concentrations of a number of light elements by bomb reduction of UF4, with calcium is described. Details of procedures are given for preparing high-purity ingredients for the bomb reduction. The as-reduced uranium metal contained, on the average, less than the following amounts of light element impurities, in ppm: Li, 0.1; Be, 0.1; B, 0.1; C, 25; 0, 70; Na, 1; Mg, 3; Al, 2; and Si, 7. Other impurities for which the metal was examined averaged, in ppm: Ca, < 10; V, < 10; Cr, 2; Mn, 6; Fe, 50; Co, < 5; Ni, 8; and Cu, 1. THE preparation of very high-purity uranium metal in massive form for research purposes is of great importance. Recently the kilogram-scale preparation of uranium metal containing less than 70 ppm of detected impurities was accomplished by Blumen-thal and coworkers by vacuum remelting of high-purity crystals of uranium obtained by fused salt electrolysis.1"3 Albert and coworkers4 have reported successful experiments in lowering the concentrations of certain impurity elements in uranium, notably iron, to a few ppm by the zone-melting method. The present paper describes the preparation of high-purity massive uranium metal by the bomb reduction of UF4, with calcium. Early in 1951 a program was undertaken at the Los Alamos Scientific Laboratory to prepare uranium metal of very high purity with respect to a number of the light elements. The methods considered for this purpose were 1) bomb reduction of a uranium halide with calcium, 2) electrolysis of fused salts, and 3) hot wire decomposition of UI4, The first of these processes had been used extensively at Los Alamos since 1943 (and still is used) for the production of uranium metal.5 In considering the three processes it was evident that either of the last two would require an extensive development program with no certainty of success. On the other hand, a study of available data showed that uranium metal of very high purity with respect to some light elements had occasionally been made in routine processing by the first method. It was therefore decided that an intensive study of the bomb-reduction process would be made to see if it could be improved to yield uranium metal with very low concentrations of light elements. DEVELOPMENT OF PROCEDURES The bomb-reduction process used at Los Alamos consists of reducing UF4 with calcium, using iodine as a booster. The reaction is carried out in a magnesium-oxide crucible enclosed in a steel bomb. Argon is used in the bomb to avoid objectionable side reactions which would occur in the presence of air. All ingredients for this bomb-reduction process were examined as possible sources of light elements. It was known that high-purity UF4 was required. The calcium used in the reductions was a source of carbon and magnesium. The magnesium-oxide crucibles were sources of boron, silicon, and magnesium. The iodine did not appear to be a source of any impurities. Pure UF4- The UF4 for bomb reduction is prepared from U3O3 , by successive reduction to UO2, with hydrogen and hydrofluorination of the UO2, with anhydrous HF. Since it was known that no impurities were normally introduced during the gas-solid reactions, effort was directed toward the preparation of high-purity U3O3. Of the many possible procedures for the purification of uranium solutions the following were investigated: 1) Precipitation of uranium peroxide. (Two procedures were tried. The first consisted of simultaneously adding hydrogen-peroxide and ammonium-hydroxide solutions to a uranyl-nitrate solution, containing citric and malonic acids, at such relative rates that precipitation was carried out at a constant pH of 1.5 The second consisted of simultaneously adding uranyl-nitrate, ammonium-hydroxide, and hydrogen-peroxide solutions to an aqueous solution

Jan 1, 1960

By Peter Greenfield, Paul A. Beck

Thirty binary systems of vanadium and chromium group transition elements with second and third long period transition elements were explored in regard to the intermediate phases formed. It was found that the phases predominating in these systems are s, AB type with ordered a-tungsten or C8 structure, close-packed-hexagonal with small unit cell dimensions and, finally, phases isomorphous with 1-manganese. IN recent years, considerable information has become available concerning the intermediate phases in binary systems of the transition elements. Thus, the s phase has been found to occur in most of the binary systems of vanadium, chromium, and molybdenum with the group of elements manganese, iron, cobalt, and nickel.&apos; It was observed that, while the rr phases formed by chromium with manganese, iron, or cobalt possess a considerable temperature range of stability, particularly in the Cr-Co system, the corresponding s phases with molybdenum are limited to a temperature range of less than 400" above about 1200°C. Goldschmidt&apos; reported v phases of tungsten with iron and cobalt, and these are apparently stable only at (and above?) 1400°C." Exploratory work in this laboratory with Fe-W and Co-W alloys of approximately 60 atomic pct W annealed at 1300°C did not produce X-ray patterns suggesting the presence of a phase. It appears then that the phases of iron and cobalt with the chromium group elements decrease in stability as the two components are chosen from long periods further removed from each other. From the available information, it might be concluded that the controlling factor is the increasing difference in atomic radii between the components. In contrast to the a phase, the phases formed by iron and cobalt with chromium group elements&apos; are stable only when the latter have large atomic radii (molybdenum and tungsten); the corresponding phases with chromium do not occur. When the difference in atomic size becomes still larger (r,/r,, approaching the ideal value of 1.225), the u and p phases are replaced by Laves phases (AB,), as in the alloys of iron and cobalt with columbium," tantalum." and titanium."-" However, atomic size certainly cannot be the sole determining factor, since, for instance, in contrast to the very stable (Mo, Co)p phase, no such phase occurs in the Mo-Ni system even though the atomic diameters of cobalt and nickel are nearly the same. Similarly, chromium and cobalt form a a phase in a wide temperature range," but the corresponding s phase in the Cr-Ni system is missing. It has been shown that the composition of the u phase in various binary and ternary systems of transition elements in the first long period may be correlated in a fairly quantitative manner with the number of electron vacancies. The influence of electronic structure is probably present also in binary and ternary phases&apos; and to some extent, apparently, even in Laves phases." " Although the absence of phases in the Cr-Ni and Mo-Ni systems has not as yet been explained on the basis of electronic structure, it appears reasonable to suspect a connection. One of the great difficulties in arriving at well founded rules in regard to the alloying behavior of transition elements lies in the lack of reliable information concerning the details of their electronic structure in the metallic and alloy form. The theoretical penetration of this field appears to be beset by very considerable difficulties, even when the complications due to alloy formation are disregarded. Another great source of uncertainty is the scarcity of phase diagram information even for binary systems of the transition elements so that only a very limited basis is provided for generalizations as to the occurrence of intermediate phases. For instance, very few binary phase diagrams of second and third long period transition element systems have so far been published. The present work was undertaken in order to survey the various types of intermediate phases occurring in 30 binary systems of elements of the group vanadium, columbium, tantalum, chromium, molybdenum, and tungsten with the elements rhenium, ruthenium, rhodium, palladium, and platinum. For most of these binary systems phase diagrams are very incompletely or not at all known, as will be further reviewed.*

Jan 1, 1957

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry&apos;s data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,&apos; is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3&apos; tests, however, this is not justified, and the D values

Jan 1, 1941

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry&apos;s data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,&apos; is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3&apos; tests, however, this is not justified, and the D values

Jan 1, 1941

By W. A. Backofen, F. de Kazinczy

FRACTURING under conditions of particular interest is identified with the junction of curves relating tensile yield and fracture stresses to test temperature; the intersection point gives the lowest stress, for brittle fracture (at the ductility transition temperature). An expression for is found in Cottrell&apos;s brittle-fracture analysis, Eq. [15],1 while measurements of this stress and temperature have been reported for a low-carbon steel heat treated to differ-

Jan 1, 1962

By Robert W. Hunt

The first pump of this character, made by H. R. Worthington, and, so far as the writer is informed, the first and only one of this kind ever constructed, is now in daily use in the above-named works. The water-pressure necessary for the working of the hydraulic machinery of this plant had been supplied, up to the time of the building of this pump, by two Worthington Duplex High Pressure Pumps, having steam-cylinders of 20 inches diameter and 12-inch stroke, with water-plungers of 71/2 inches diameter; eight inlet and eight outlet valves of 24 inches diameter, and pumping into a 6-inch pipe. These pumps required a large amount of steam, and, in consequence of the various additions to their duty, their capacity became far short of the work required. In preference to putting in another engine of the same class, it was decided to accept Mr. Worthington&apos;s proposition to build the compound one under description, he guaranteeing that it should be equal to the demands of the works, and at the same time cause a saving of from 5 to 6 tons of coal per day from the amount required to run the two old pumps. The new engine has been in operation about one month, and so far has exceeded the most sanguine expectations. It consists of two high-pressure cylinders of 21 inches and two low-pressure ones of 363/8 inches diameter, by 36-inch stroke, with water-plungers of 961/2 inches diameter. There are two air-pumps of 20 inches diameter by 18-inch stroke; the condenser being 24 inches diameter by 60 inches high. Both cylinders are jacketed with wood and felt, and the low-pressure cylinder also with live steam. The high and low pressure steamcylinders are in line and immediately adjoining each other, while the inconveniences attending an internal stuffing-box are avoided by having two piston-rods for each of the low-pressure cylinders, running through stuffing-boxes on the outside of the smaller high-pressure ones. The steam-valves are very ingeniously designed balanced

By James Paul

BEGINNING in December, 1933, and continuing to the close of April, 1934, large sums of money were expended in the states of Pennsylvania, Ohio and West Virginia through the conduct of Federal and State Civil Works Administration, financed by the Government as a part of the President&apos;s recovery program to furnish employment to mine employees idle as a result of the economic depression. PURPOSE OF THE PROJECT The protection of the public health against the pollution of public water supply by acid mine drainage was the incentive that prompted the request that the sealing of abandoned bituminous coal mines be made a Federal project. A paper before the Central Section of the American Water Works Association, Wheeling, W. Va., on Aug. 24, by E. S. Tisdale, Chief Engineer of the West Virginia Department of Health, tersely says: In October, 1933, the combined experience of the U. S. Bureau of Mines and the U. S. Public Health Service and the States of Pennsylvania, Ohio, West Virginia and Kentucky resulted in a report being filed in Washington, first with the Public Works Administration and later with the Civil Works Administration, where it was favorably acted upon, calling for these governmental agencies under the direction of the U. S. Public Health Service to expend $1,500,000 in a unified effort to seal abandoned coal mines in Pennsylvania, Ohio, West Virginia, Kentucky and six other states farther down along the Ohio river. The report referred to was embodied in a petition that was signed by the chief engineers of the State Departments of Health of the several states contiguous to the drainage area of the Ohio River. The project as established under Federal supervision became interstate with respect to the several states involved, and upon the termination of the Federal project on Feb. 15, it was authorized as a State C.W.A. project, effective Feb. 20, under the supervision of the State Departments of Health and the State C.W.A. Administration, which continued to March 29, and was succeeded by the S.E.R.B. of the R.W.D. from April 2 to April

Jan 1, 1935

By M. R. Tek, L. K. Thomas, D. L. Katz

Threshold displacement pressures are needed to determine how much overpressure can be used in storing natural gas. An experimental technique for determining threshold pressures by displacing water with gas from samples saturated with water is presented. Threshold pressures for eight low permeability samples were measured. Threshold pressure data obtained in this work, plus data on higher permeability samples reported in the literature, are correlated with porosity, permeability, surface tension and formation resistivity factor. Mercury injection pressures also were measured and correlated with air-water threshold pressures. Threshold pressures were found to be independent of time. An aerial photograph of gas emerging from the top of a core shortly alter its threshold pressure has been exceeded shows that the gas bubbles are uniformly distributed across the face of the core. Channeling will occur, however, when an increased gas phase permeability is reached, A porous medium can be re resealed alter its threshold pressure has been reached, provided it has not been desaturated below a fixed saturation. Its new threshold pressure will be lower than when the sample is 100 percent saturated with water. INTRODUCTION The degree of overpressure in excess of the discovery pressure that a gas storage reservoir can withstand is determined by the ability of its caprock to contain gas, providing the pressure does not exceed the structural limit of the reservoir. The retention of gas in a reservoir by a caprock saturated with water is a result of the capillary forces acting at the gas water interface. Without the presence of water in a caprock, gas would leak out of the reservoir at a rate determined by the permeability of the caprock to gas. The ability of a caprock to contain gas is expressed in terms of its threshold displacement pressure, which is defined as the minimum pressure needed to initiate the displacement of a wetting phase by a nonwetting phase from a porous medium 100 percent saturated with the wetting phase. The gas industry must be able to predict how much "overpressure" a gas reservoir can withstand before leakage occurs by gas displacing water from caprock overlying the reservoir. This is of economic importance since the storage capacity of a gas reservoir is proportional to its pressure. The discovery pressure for most reservoirs is found between the upper and lower limits1 shown in Fig. 1. Discovery pressures in excess of their hydraulic pressure gradient are attributed to the compaction of an isolated shale formation by the overburden.2.3 The lower limit of 0.433 psi/ft corresponds to the weight of the overburden, the gradient of the rock itself. Somewhere between

Jan 1, 1969

By John M. Sharp

John M. Sharp, Jr. (Assistant Professor of Geology, University of Missouri, Columbia, Mo.)-Geothermal gradient and surface temperature data anomalies are potentially useful tools in mineral exploration, These data, however, may reflect a number of geologic and hydrologic processes as well as the thermophysical properties of the geologic materials. The author presents a relatively simple model which may be of value in mineral exploration. The lack of consideration of other processes, however, limits its usefulness. For instance, because of erosion or sediment deposition over geologic time the land surface must be considered a moving boundary in such a model. Evaluation of this effect coupled with annual surface temperature and thermal conductivity variations can result in temperature profiles such as shown in [Figs. 4 to 7]. These effects and others, such as ground-water movement," must be considered and filtered from the data before proper interpretation is possible. Another assumption which should have been discussed is, why were the observed mean surface temperatures not used for extrapolation of the gradients in [Figs. 4, 6, and 7?] Conductive heat transport responds to the actual boundary (land surface) temperature, not to theoretical temperatures in the absence of perturbations. Benfield presents a theoretical model for calculating perturbations in the geothermal gradient for erosion and sedimentation. The temperature (T) at any time (t) and any depth below the surface (x) is given by [ ] where T is the mean surface temperature, G, the geothermal gradient, v, the rate of erosion (or sedimentation),[ ], the long-term rate of change of T0, and k is the thermal diffusivity of the rock. Using the author&apos;s values and a rate of erosion of 1.54 cm per yr for a period of 10,000 yr, a thermal profile as shown in [Fig. 10] will be generated. A thermal diffusivity of 0.0164 sq cm per sec was used, corresponding to a thermal conductivity of 0.0082 cal per cm per sec per C. In [Fig. 11], a sediment deposition rate of 3.0 cm per yr for a period of 1000 yr was used to generate the subsurface temperature profile. A surface temperature of 24.3°C was used, as specified in [Fig. 9, 7], was set equal to zero for both cases. Superposition on the generated profiles in [Figs. 10 and 11] of the annual surface temperature variation perturbation (which may be calculated in a number of ways) will yield profiles similar to those in [Figs. 4 and 7]. Similar profiles can also be produced by regional ground-water flow. Models like the author&apos;s can be of value in mineral exploration. Other processes, however, which affect surface temperatures and gradients must first be considered, calculated, and filtered from the data if anything but the crudest qualitative interpretation is to be made. Robert C. Edmiston (Author&apos;s reply)-Professor Sharp has raised three objections to my interpretation of the subsurface temperature data I collected at Silver Bell. These are: 1) No correction was made for erosion or sedimentation,

Jan 1, 1977

By Seymour G. Epstein

Using a modified capillary-reservoir technique, electromigration of dilute solutions of silver in liquid bismuth has been measured with relatively good precision. The effects of experiment duration, temperature. current density, and silver concentration have been investigated. Chemical diffusion coefficients of silver in liquid bismuth were also measured at temperatures ranging from 300°to 600°C. The effective valence of silver in bismuth was calculated as a function of temperature from a comparison of electric mobilities and diffusion coefficients. In an alloy containing 1 wt pct Ag, the electric mobility of silver increased from 1.65 x X sq cm per v-sec at 300°C to 2.38 x 10-4at 600°C; the diffusion coefficient in-creased from 3.0 to 17.5 x 10-5 sq cm per sec over the same temperature range. Calculated values of effective valence decreased from 0.28 at 300°C to 0.10 at 600°c. ALTHOUGH there has been considerable progress in the theoretical treatment of electron-transport properties in liquid metals, the mechanisms of mass-transport phenomena in liquid metals are still not clearly understood. This is especially true for the case of electro migration, alternatively termed elec-trotransport or electrodiffusion, which is mass transport induced by an applied electric field. A thorough knowledge of the mechanisms governing electromigration will considerably aid in understanding the electronic state of an impurity atom in a liquid metal. Electromigration has been long observed and studied in liquid metals and alloys. However, no satisfactory theory to explain the observed effects has been developed. The disparity in the present theoretical treatments, summarized by Verhoeven,1 has been attributed to the difficulty in describing the momentum transfer between electrons and ions and to the lack of precise measurements in liquid metals, especially at elevated temperatures. Prior to the last decade most of the electromigration studies were qualitative, in that only the direction of migration of alloy constituents was determined with any degree of reliability. These results have been summarized by schwarz,2 who was able to measure the electric mobility of several elements in mercury. More recently electromigration in liquid metals has been measured by a variety of techniques, with a varying degree of success. Mangelsdorf3,4 made precise measurements on dilute amalgams at room temperature, using a technique relating changes in composition to changes in alloy resistivity, but was unable to make measurements at elevated temperatures. Using a modification of this technique, Verhoeven and Hucke5 measured electromigration and resistivities in liquid Bi-Sn alloys. However, the resistivity technique is not sensitive to small composition changes and is impractical for very dilute alloys. Verhoeven and Hucke6 also measured electromigration of several solutes in liquid bismuth by adapting the capillary-reservoir method for determining diffusion coefficients in liquids. The reported precision of these measurements was poor, however, primarily due to the large uncertainties in the chemical analyses to determine concentration changes. Belashchenko7 has summarized the recent Russian investigations of electromigration, many of which, however, are of questionable accuracy. The present study was initiated to develop an experimental technique which would be both versatile and sufficiently sensitive to yield precise measurements of electromigration of solutes in dilute metal alloys at elevated temperatures. Using this technique, a comprehensive study of silver in liquid bismuth was made to determine the effects of experimental variables on the apparent electric mobilities. Chemical diffusion coefficients of silver in liquid bismuth were also measured over the same temperature range for comparison with the electromigration data. EXPERIMENTAL TECHNIQUE Electromigration Measurements. Electromigration of silver in liquid bismuth was measured by the capillary-reservoir technique, similar to that used by Verhoeven and Hucke,6 but modified to yield more

Jan 1, 1967

By Cyril Wells, Robert F. Mehl

THE practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out 1,13 This importance ties chiefly, though by no means only, in the study of carburizing and in the study of reactions involved in the eutectoid inversion in steel The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in y-Fe and their mutual effects are measured with precision The present paper reports the results of meas¬urements of diffusion coefficients D of manganese in -y-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients [$] Data on the rate of diffusion of manganese in y-Fe have been reported by Fry2 and by Paschke and Hauttmann 3 Claussen4 calculated the diffusion coefficient D from Fry&apos;s data as 3 X 10-10 sq cm per sec at 960°, which will be shown to be incorrect by many orders of magnitude Paschke and Hauttmann gave a rough value of 9 6 X 10-8 sq cm per sec at 1400° Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon METHOD AND MATERIALS Method -The method employed is identical with that used earlier 5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded The diffusion anneals were performed in argon, except one (test 18) in which hydrogen was employed for purposes noted below The temperatures reported are accurate to about 3° and constant within I°C , the diffusion times are reported to the nearest half hour The specimens were furnace-cooled after the diffusion anneal at about 2° per min Layers, usually 0 004 in thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0 01 per cent Mn, the distances of these layers from the interface was measured to ±0 0002 in The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions e The D values calculated by these two methods do not differ appreciably 5 The Grube solution was used except in tests in which the effect of concentration upon D was greater than 50 per cent, in such cases the Matano method, which explicitly provides for the variation of D with concentration,1 is the more reliable In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer In 3 of the 30 tests, however, this is not justified, and the D values

Jan 1, 1941

ASHBEL WELCH, LAMBERTVILLE, N. J.: Dr. Dudley has given the wear of steel rails under four different conditions. He arrives at the conclusion that the softer rails, or those that from their composition ought to be softer, wear better than the harder. But there is another condition which has an important bearing on the subject, and, should not be overlooked,-the weight on a wheel. With the lighter weights of the past, the softer rails may have worn best; with the heavier weights of the future, the harder may wear best. Weights will probably be increased up to the capacity of steel to bear; then doubtless the harder steel will wear best. A leaden rail with ten pounds on a wheel might carry millions of tons, but with one hundred pounds on a wheel, it would be destroyed by a few thousand tons. So in the days of iron rails, my experience was that the softer rails under light machinery stood better than some of the harder; but under heavy machinery the softer were much the most rapidly destroyed. His doubtless the same with steel. The pounding motion of the wheels loosens or spreads the particles of a thin film of steel; the pull lengthwise on the rail de- * Metallurgical Review, vol. i, page 1. † The remarks as here given, as in the previous discussion on steel rails, have all been written out or revised by the participants in the discussion, and represent, therefore, their mature views. It has been thought that this plan, when it can be carried out without doing any of the speakers injustice in debate, is much to be preferred to a strictly verbatim report. The remarks of Mr. Chanute were sent to the secretary after the. meeting, and although they did not form a part of the actual discussion, there can be no doubt of the desirability of including them in this report. The papers under discussion were “Rail Specifications and Rail Inspection in Europe,” by C. P. Sandberg ; " The Wearing Capacity of Steel Rails in Relation to the Chemical Composition and Physical Properties," by C. B. Dudley, and a Rail Patterns," by A. L. Holley. T. M. D., Secretary.

Jan 1, 1881

By F. C. Sturges

For some time mining engineers have been interested in the possibility of using small diameter shafts, sunk by core drilling, as aids to ventilation and as emergency escapeways. The possibilities are interesting to contemplate, but new methods involve unknowns, and interest tends to remain passive until these unknowns are, solved. Recently we have completed two 36-in. diam core drilled shafts, and wish to make the data on these available to the industry. Both shafts were drilled for the McLain Fire Brick Co., one at its Buckeye mine and the other at its Colonial mine. Both mines are in the fireclay underlying the Lower Kittanning coal. Both mines have been in operation for a number of years and have required expensive maintenance work on return airways. It was decided that considerable savings could be effected by short-circuiting the air to the surface through small shafts. It was also realized that these holes, located near the present workings, would be of added value as emergency escapeways. Originally, 48-in. diam shafts were considered, but actual computations showed 36-in. diam shafts were more than ample at both mines. The shaft at the Buckeye mine is 240 ft deep, and that at the Colonial mine 258 ft deep. Both holes were started in the lower part of the Conemaugh formation and penetrated Conemaugh and Allegheny strata. The holes were started through the unconsolidated materials overlying bedrock by constructing a concrete collar with a wall thickness of 8 in. Then the shafts were drilled by the shot-core drill method. An annular groove was cut in the rock by the abrading action of chilled steel shot run under the shoe of the core barrel. The drilling was done in stages, the core barrel drilling the groove for a certain distance depending on conditions encountered, and then the cores broken off and taken out in sections. The core barrel had a 36-in. o.d. and the finished diameter of the shaft measured almost 37 in. The major questions that could not be answered until the completion of the first shaft were, (I) how much ground water would be encountered, how would it hinder the drilling, and how difficult would it be to seal off, and, (2) how would the walls of the hole stand up. The holes of course could .be cased or lined, but that is considerable added expense in any shaft.

Jan 1, 1949

By Ben B. Sweet

The ongoing controversy over mining and agricultural use of ground water in Arizona underscores the importance of this commodity to both industries. Although the principles presented in this article are fundamental, a method of systematic data collection and interpretation is provided for evaluating a water well by a set of uniform standards common to all areas where ground water is a primary source of supply.

Jan 8, 1978

By C. H. Jr. Herty

The results of a study of the open-hearth process from the physicochemical view-point are given. This study includes experimentation in small laboratory furnaces and in standard 100-ton furnaces. The behavior of manganese, carbon, and phosphorus are quantitatively explained. The action of "residual" manganese is discussed with reference to its relation to iron oxide dissolved in the metal. The solubility of CO in steel and its relation to dissolved FeO and carbon is given. The equation for phosphorus elimination has been tested out on a 200-ton furnace and the results are given in the text. THE effect of temperature and slag composition on the elimination of metalloids in the basic open-hearth process has been qualitatively understood since the early days of steel making. The quantitative effect has, however, only recently been brought to attention. The effect of slag composition has received more attention than that of temperature, primarily because the range of finishing temperatures in the basic open-hearth process is small compared to the large variations found in the composition of the slag at different periods during the process, and to the variations occurring with the use of raw materials of different degrees of impurity. The effect of slag composition on the elimination of metalloids has been studied by Styri1 from the thermochemical standpoint. This method is open to serious errors, in that thermochemical data at 2900° F. are very inaccurate and in many cases completely lacking. Feild2 has calculated equilibrium constants from the rate at which the metalloids are eliminated. The effect of slag viscosity on rate of elimination will affect the constants calculated by this method. Whitely,3 Colcough4 and others have used slag compositions as the basis for calculation of constants by which the extent of elimination may be calculated.

Jan 2, 1926

By H. R. Coles, S. P. Chong

Test work conducted in the 6.4 and 10.5 m (21 and 34 ft) Aerofall mills at the Iron Ore Co. of Canada Carol project showed that conventionally used "deflector" type liners, which form the basic principle of Aerofall Mill grinding, did not necessarily provide the best grinding performance. A new design, using low profile liners incorporating radial ribs of proper height, actually improved the mill throughput 9-20% without sacrificing grinding efficiency. In addition, the new design reduced liner weight and scrap losses, resulting in a 25% reduction in liner consumption. It provided better protection to the mill shell and reduced the overall maintenance cost for the mills.

Jan 1, 1984