Search Documents

By C. G. Dunn, J. L. Walter

The c/laracterzstics of cube-oriented nuclei ard other matrix grains that are associated with secondary, recrystallization to the cube texture in high-purity silicon iron were investigated by me-tallographic and X-ray methods. The results show that the structure consists of relatively perfect grains of average diameter between one and two times the sheet thickness ad that the texture has a moderately strong (110) [001] component and a weak (100) [001] component. The results also indicate that matrix stability results from the two-dimensional nuture of the graitzs and that cube-orzented nuclei are neither more Perfect nor larger grains than other matrix grains but have a preferred [001] direction in the rolling direction and have a more effective driving force for growth than other grains because of a low (100) surface energy. THE structures and textures of fine-grained rnatrices determine to a large extent the kinds of secondary recrystallization textures that form on annealing. The understanding of secondary recrystallization processes therefore depends on adequate information about the initial matrices. Matrices usually have three characteristics: 1) they consist of fine-grained primary recrystallization structures, 2) the fine-grained structures are stable toward normal grain growth, and 3) they contain secondary recrystallization nuclei. Stability toward normal grain growth may be due to either a strong single orientation texture (texture inhibition)' or a dispersed second phase (dispersed phase inhibition).2"4 If normal grain growth is not inhibited by either of these two factors, it nevertheless stops when the average grain size is between one and two times the sheet thick- ness.5 This thickness effect satisfies one of the characteristics of a matrix for secondary recrystallization. Its importance in the development of the cube texture in high-purity silicon iron by secondary recrystallization was pointed out by the authors in a recent paper on tertiary recrystallization7 and will be discussed further in the present paper. Assmus, Detert, and he8 have provided some information on a matrix for secondary recrystallization to the cube texture in silicon iron. They found a (110)[001] or Goss texture with enough spread about the rolling direction to include a small amount of the (100)[00l] orientation. The distribution of the [00l] directions was strongest parallel to the rolling direction for both (100) primaries and cube secondaries. These authors found no correlation between size of a matrix grain and orientation and concluded that some property other than size must be the distinguishing characteristic of the cube-oriented nucleus. No consideration was given, it

Jan 1, 1961

By F. H. Buttner, H. Udin, J. Wulff

Using a modified Udin, Shaler, and Wulff technique, the surface tension of gold Udin, purified helium was found to be 1400 ± 65 dynes per cm for the temperature range 1017° to 1042°C. IN the original Udin, Shaler, and Wulff technique for measuring the surface tension of copper: variously weighted wires were allowed to extend or contract in a copper cell held at elevated temperatures in vacuum. By plotting stress vs. strain for a wire array in one test, the stress at zero strain is obtained. This is the point where the contractile forces resulting from surface tension are balanced by the applied load, according to the expression: y = e=o r [1] where y is the surface tension in dynes per cm; a,,,, the stress at zero strain in dynes per cm; and T, the radius of the wire in cm. The assumption that the wires deform viscously permits the drawing of a straight line through the points on the stress-strain plot. Justification of the assumption has received further experimental support recently.'-' The presence of grain boundaries in the wires requires a correction to the original expression used." Thus: y = d4=T [l- (dl) (ar)Y1 [2] where, n/l is the number of grain boundaries per unit length, and a, the ratio of grain boundary tension to free surface tension. Alexander, Kuczynski, and Dawson in studying the creep of gold wire in vacuum were unable to obtain reproducible values of the surface tension of gold. In plotting stress vs. strain for progressively longer times, they found that the stress at zero strain drifted with time from positive stress values to negative values. Similarly, for the surface tension of silver, reproducible values were obtained only when a purified helium atmosphere was substituted.' Evidently the evaporation rate of silver in vacuum is too high at the temperatures employed to obtain solid-gas equilibrium even in a similar metal enclosure. Thus reproducibility of results is lost. Experimental Procedure The experimental procedure was much the same as that originally developed by Udin, Shaler, and Wulff with a few modifications and improvements. For greater accuracy in strain measurements, knots gave way to cut gage marks as shown in Fig. 1. These were made with a hand-driven lathe in which razor blades serv'ed as cutting tools. Also a more precise cathetometer with a screw accurate to 0.00015 cm was used. The tests were conducted in an atmosphere of purified .helium rather than in vacuum in order to avoid possible evaporation difficulties. Five mil wire of high purity gold (99.98 pct) was used. After cutting in the gage marks, each wire of a series of about 12 was differently loaded by welding a gold ball to one end. This was done by dipping the end of the wire in a cooling gold droplet, previously melted on a charcoal block with a No. 2 acetylene torch. The other end of the wire was strung through a hole in a gold lid and twisted over the edge to hold the wires fixed and in suspension from the lid. The lid and mounted wires were then dipped in pure ethyl alcohol to dissolve any skin oils and dirt on the surface of the wires due to handling. Finally the lid was put in place on an alundum crucible lined with gold so that the wires hung freely within the gold-lined chamber. This whole assembly was next heated in a quartz nichrome wound tube furnace and heated for a few minutes at 600°C to soften the wires. After this anneal the wires were easily straightened with tweezers. The wire assembly was finally annealed 10" to 25°C above the subsequent test temperature for 2 hr. This treatment allowed the grains to grow to equilibrium size and shape. After the anneal, the lid was mounted in front of the cathetometer. The gage length was measured by sighting the 40 power microscope on the upper lip of the lower gage mark for the first reading, then traveling up to the lower lip of the upper gage mark for the final reading. This procedure was repeated four times to give an average gage length value. In this manner the annealed gage length and the final gage length could be measured to determine the strains. During all measurements, grain counts were made.

Jan 1, 1952

By Willis R. Battles, William F. Cerini, P. H. Jones

A test for determining the plugging characteristics of an oil-well injection water has been developed. It consists in measuring changes of the filter rate of a water at constant pressure with cumulative throughput when passing the water through a medium grade sintered glass disk. Application of the test method was made to the water used in the Union Oil Company's experimental water flood of the Chapman zone in the Richfield field, Orange County, Callfornia. This water developed increasing plugging tendencies upon aging, even though the finished water from the plant filter exhibited few such characteristics. The plugging material was found to consist of calcium carbonate, ferric hydroxide, and organic substances that were presumed to be bacterial. Various method of stabilizing this water to prevent the formation of plugging material were attempted. Lowering the pH to approximately 6.4 by injecting carbon dioxide provided a moderately satisfactory means for stabilization but a better method of stabilizing this water was found to be first aging and then filtering. Introduction An experimental water-flood project was started on the Chapman zone of the Richfield field in March 1944 and has been described in a previous paper.' It consists of a single injection well drilled between old producing wells. A water-treating plant using primary alum flocculation, sedimentation and chlorination followed by secondary flocculation, sedimentation and fltration is employed to process the water before in@ion. In all of the water-treating operations, the system is open to the air, and no attempt is made to prevent the loss of carbon dioxide or absorption of oxygen by the water. The clear water is stored in a covered concrete basin and pumped through a Transite line to the suction of a high-pressure pump at the injection well' The high-pressure tubing in the well to the injection zone is cement lined. The untreated injection water is a mixture produced with the oil from the Chapman and Kraemer zones and is supplied from the disposal system. Because the injection well was relatively deep (injection zone about 3400 ft.) and would be expensive to replace, it was believed imperative to supply a nonplug-ging injection water and to develop laboratory procedures for evaluating the treated injection water with respect to its formation plugging properties. This report describes the development and application of the test procedure based on the assumption that the plugging properties could be determined by measuring the progressive decrease in flow rate of the water through a porous medium. If the quality of the injection water was good enough so that the plugging action on the porous medium was of small magnitude, it was reasoned that the tendency to impair flow in the formation would not be serious.

Jan 1, 1946

By William F. Cerini, Willis R. Battles, P. H. Jones

A test for determining the plugging characteristics of an oil-well injection water has been developed. It consists in measuring changes of the filter rate of a water at constant pressure with cumulative throughput when passing the water through a medium grade sintered glass disk. Application of the test method was made to the water used in the Union Oil Company's experimental water flood of the Chapman zone in the Richfield field, Orange County, Callfornia. This water developed increasing plugging tendencies upon aging, even though the finished water from the plant filter exhibited few such characteristics. The plugging material was found to consist of calcium carbonate, ferric hydroxide, and organic substances that were presumed to be bacterial. Various method of stabilizing this water to prevent the formation of plugging material were attempted. Lowering the pH to approximately 6.4 by injecting carbon dioxide provided a moderately satisfactory means for stabilization but a better method of stabilizing this water was found to be first aging and then filtering. Introduction An experimental water-flood project was started on the Chapman zone of the Richfield field in March 1944 and has been described in a previous paper.' It consists of a single injection well drilled between old producing wells. A water-treating plant using primary alum flocculation, sedimentation and chlorination followed by secondary flocculation, sedimentation and fltration is employed to process the water before in@ion. In all of the water-treating operations, the system is open to the air, and no attempt is made to prevent the loss of carbon dioxide or absorption of oxygen by the water. The clear water is stored in a covered concrete basin and pumped through a Transite line to the suction of a high-pressure pump at the injection well' The high-pressure tubing in the well to the injection zone is cement lined. The untreated injection water is a mixture produced with the oil from the Chapman and Kraemer zones and is supplied from the disposal system. Because the injection well was relatively deep (injection zone about 3400 ft.) and would be expensive to replace, it was believed imperative to supply a nonplug-ging injection water and to develop laboratory procedures for evaluating the treated injection water with respect to its formation plugging properties. This report describes the development and application of the test procedure based on the assumption that the plugging properties could be determined by measuring the progressive decrease in flow rate of the water through a porous medium. If the quality of the injection water was good enough so that the plugging action on the porous medium was of small magnitude, it was reasoned that the tendency to impair flow in the formation would not be serious.

Jan 1, 1946

By P. van Meurs

This paper describes a technique which permits visual observation of oil displacement processes througlrout the interior of a porous structure as thick as 2 in. A model having glass walls is filled with finely powdered glass. Such a model becomes completely transparent if the powdered glass pack is saturated with an oil having the same refractive index as the glass. When water or gar, with a refractive index different from that of the oil (glass) is injected, the model becomes opaque in the space occupied by the water (gar). visual observation and photography of these displacement processes are thus rendered possible. The following processes have been studied: (I) displacement of oil by water (linear drive) in a homo-geneous formation and in a stratified formation, (2) water flooding (five-spot well pattern), (3) solution gas-drive process, and (4) oil-bank formation. INTRODUCTION Most of the scaled model experiments heretofore carried out in the Koninklijke/Shell Laboratorium, Amsterdam, have been done in steel containers, in which oil-saturated sand packs represented the oil-bearing formation. In such experiments, for instance those on the displacement of oil by water, the cumulative oil production was measured as a function of the cumulative water injection. In order to interpret the measured production data, a need has for some time been felt for a means of observing visually what happens in the course of such experiments. Some information of this kind was obtained earlier by observing the water-oil distribution in various cross sections of the sand after the conclusion of the experiment.' However, the technique used did not guarantee that the fluid distribution remained undisturbed. Moreover, the procedure was somewhat elaborate and the information obtained limited. Therefore a new technique has been developed, which is described below. DESCRIPTION OF EXPERIMENTAL TECHNIQUE AND APPARATUS Glass models simulating part of an oil reservoir are filled with ground Pyrex glass of a specific grain size, representing the porous structure of the prototype. Before an experiment is started, the porous formation has to be saturated completely with an oil having exactly the same refractive index as the Pyrex glass powder. All light-scattering surfaces of the glass grains become invisible and the formation is then transparent. If the oil is displaced by another fluid (e.g. by water in a water-drive experiment, or by gas liberated from the oil in a solution gas-drive experiment) the formation becomes opaque in the region where the oil is expelled from the rock.* The back of the apparatus is painted black and illumination is from the front; therefore, in the photographs of the experiments, the oil-bearing formation appears black, whereas the water- or gas-invaded areas are white.

Jan 1, 1958

By G. W. Cullen

Niobium-tin has been prepared on insulating suhstrates hby simultaneous hydrogen reduction of gaseous niobium and tin halides. Stoichiometric material is greater than 98.8pct theoretical density, appears to he single-phase, and has a total impirity level less than 0.3 at. pct. Transition temperatures and lattice constants may he related to composition. Typical current densities in various fields and orientations are given. IT is known that Nb3Sn carries large current densities in high fields, 1 and exhibits an unusually high transition temperature2 and critical field.3 For these reasons high-field solenoids have been constructed of this material.4 Because of the emphasis on solenoid fabrication, much of the materials research has been directed toward development of wire geometries wherein the brittle Nb3Sn is supported by a more malleable metal or alloy. There are, however, basic studies and applications that can be carried out only on Nb3Sn supported by an insulator. Insulating substrates are desirable for a number of reasons: the substrate does not interact with applied or induced currents and fields; diffusion of metallic species into the de- posit is avoided, both during the preparation and during subsequent heat treatment; irradiated samples are not more active than the deposit itself. Unsupported Nb3Sn geometries may also be prepared by preferential chemical dissolution of the insulating substrate. This report describes the preparation and properties of Nb3Sn deposits on ceramic substrates. Experiments currently utilizing material prepared in the manner described in this report include the following: dependence of current-carrying properties on field strength and orientation 5,6 radiation damage,7,8 tunneling,9 thermal conductivity (substrate removed),1° microwave surface impedance," tube magnetization,6,12 resistivity as a function of temperature,13 and current density and transition temperature as a function of annealing.14 Possible practical applications include magnetic shielding, superconductor generators, and frictionless bearings. PREPARATION Methods for the deposition of elemental niobium and tin by hydrogen reduction of the gaseous metal halides have been known for some time,15,18 but only recently a procedure was developed in this laboratory17 for the codeposition of these two metals on a hotwire as the intermetallic compound, Nb3Sn. This method of simultaneous hydrogen reduction of the gaseous niobium and tin chlorides is used for the preparation of Nb3Sn On ceramic substrates. The procedure differs from that employed on a hot wire in that insulating substrates cannot conveniently be heated to temperatures greater than their surround-

Jan 1, 1964

By L. A. Roe

The flotation of fine particles less than five microns in diameter and the flotation of liquids from liquids generally requires bubble generation methods different than methods used in dispersed air type machines used in mineral flotation. Conditions in the separatory zone in mineral cells are generally more dynamic as compared to the quiescent conditions often absolutely necessary for the flotation of fine particles and liquids. An example of quiescent flotation with very fine bubbles is the lithium flotation plant which operated at Trona, California for 34 years, until it ceased operations in 1978. A review of the process development and the commercial flotation operations at Trona is given in this paper. The clarification of oil field brines by flotation of the oil from the brine has been used for over twenty-five years. Recent installations related to the Prudhoe Bay oil field and the Alaska pipeline are described.

Jan 1, 1980

By D. W. Levinson, L. E. Tanner

DURING the course of an investigation of the zirconium-iron-tin system the zirconium-iron system was reexamined up to 55 pct* Fe. The alloys pre- visible melting3 and X-ray diffraction studies were made of samples of the alloys. The ferromagnetic properties of ZrFe2were determined by Professor P. W. Selwood* using a modified Faraday balance.4 The zirconium-rich portion of the phase diagram is presented in Fig. 1 and compared with the work of Hayes et al.1 The maximum solubility of iron in ß is somewhat decreased while the eutectic temperature is raised. There seemed to be no change in the eutectic composition of 16 pct Fe. Since the base material was so low in iron content, it was possible to establish the maximum solubility in a between 0.017 and 0.025 pct Fe at the eutectoid temperature. The observation of fine ZrFe, particles in the micro structure of a specimen of 0.012 pct Fe alloy quenched from 700°C indicated that the solubility drops below this composition at 700° C and lower. Further study was made of the intermediate phase ZrFe2. wallbaum5 identified the compound initially as ZrFe2 with a C 15 (MgCu2) structure, placing it at 55 pct Fe stoichiometrically. Hayes et al.1 believed they found the phase at about 47.2 pct Fe and called it Zr2Fe3 but reverted to ZrFe, in the discussion of their paper.6 Jordan and Duwez7 confirmed Wallbaum's work as well as finding the same single-phase structure to about 62.3 pct Fe or Zr0-61 Fe2-18. In order to establish the ternary phase relations in the zirconium-iron-tin systema the exact position of this phase had to be known. This was accomplished by X-ray diffraction, visible melting, and metallographic techniques. Elliott8 obtained a single-phase ZrFe2 X-ray diffraction pattern from an alloy of about 55 pct Fe. This was confirmed in the present study with an alloy of 54.81 pct Fe. However, extra lines (attributable to a or ß zirconium) were found in diffraction patterns of the 47.42 and 49.83 pct Fe alloys. The melting characteristics of these same alloys were studied by suspending 47.42, 49.83, and 54.81 pct

Jan 1, 1960

By Che-Yu Li, J. L. Gregg, W. F. Brehm

Oriented, oxygen-doped niobium bicrystals were tested in liquid lithium. The grain boundaries were attacked preferentially. The depth of the penetrated zone varies as (time)2. The penetration was aniso-tropic, had a high activation energy, and increased with the increased oxygen doping level. A possible model was proposed to account for the experimental observations. 1 HE grain boundary penetration of a metallic system by liquid metal has been studied by several investigators. Their results are summarized by Bishop.' Most of these works show that the penetration by liquid metal corresponds to the phenomenon of liquid metal wetting. In the case of a grain boundary, wetting will occur when twice the solid-liquid interfacial tension is smaller than the grain boundary tension resulting in the replacement of the grain boundary by two new solid-liquid interfaces. Other possibilities exist; for example, the atoms of the liquid metal may diffuse into the grain boundary region due to chemical potential gradient. The gradient can be produced by impurity segregation or simply be due to the increase in solubility in the grain boundary region. The penetrated grain boundary in these cases may remain solid at the test temperature. The Nb-Li system has been of considerable interest because of its possible technological applications. For fundamental interest it provides a possibility of studying the grain boundary penetration process which is not controlled by the wetting mechanism. The pure niobium is not attacked by the liquid lithium, but if niobium containing more than 300 to 500 ppm oxygen by weight is exposed to liquid lithium, corrosion occurs at the solid-liquid interface and preferentially at grain boundaries. Previous investigators2-' have proposed that this preferential corrosion at grain boundaries is caused by oxygen segregation there, with subsequent inward diffusion of lithium to form a Li-Nb-0 compound. These investigators also found that the corrosion could be retarded by adding 1 pct Zr to the niobium to precipitate the oxygen as ZrO2 upon proper heat treatment. However, there are no quantitative data on the kinetics of the grain boundary penetration process to test the validity of the proposed corrosion mechanism. In this work an investigation of this penetration process in oriented bicrystals was made as a function of the oxygen doping level in the bulk niobium and the grain boundary orientation. A possible model for the penetration process based on the experimental results was proposed. EXPERIMENTS Oriented niobium bicrystals were grown by arc-zone melting oriented single-crystal seeds.7 These bicrystals contained simple tilt boundary. The [001] directions in the two grains were tilted about a common [110]. The bicrystals were 31/2 in. long and 5 by 4 in. in cross section with the straight, symmetric, planar grain boundary longitudinally bisecting the crystal rod. The bicrystals were doped with oxygen by anodically depositing a layer of Nb2O on the surface in a 70 pct HNO solution at 100 v, using a stainless-steel cathode. The specimens were homogenized by annealing in evacuated quartz tubes at 127 5°C. Oxygen content of the niobium was measured from microhardness values, after DiStefano and Litmman.' Supplementary checks were made with vacuum-fusion analysis.7 Individual test specimens cut from the doped bi-crystal rods, about by by % in. in size, were tested inside double jacket sealed capsules. The inner jacket was niobium, the outer was stainless steel. The niobium inner jacket eliminated the problem of dissimilar-metal mass transfer.' The lithium (99.8 pct pure, obtained from Lithium Corp. of America) was handled only in a purified argon atmosphere in a Blickman stainless-steel glove box. After introduction of lithium, the capsules were sealed by welding. Further detailed experimental procedures are given in Ref. 7. The capsules were heat-treated in vertical Marshall resistance furnaces. Temperatures were controlled to When heating above 1100°C, it was necessary to seal the furnace work tube and flow argon through to prevent failure of the stainless-steel outer jacket of the capsule. Tests were made on 6" 2", 16" 2, and 33" i2" bicrystals at oxygen levels up to 2600 ppm by weight in the 6' and 16" crystals and with 1300 ppm oxygen in the 33' crystals. The oxygen levels were controlled to 100 ppm. Most of the quantitative data were obtained from 16" bicrystals between 800" and 1050°C. The capsules were quenched into water after the test and cut open with a water-cooled abrasive wheel. The capsules were then submerged in water, which dissolved the lithium and freed the specimen. Measurement of the depth of the penetrated zone in the grain boundary was done either on metallographically prepared surfaces or directly on the grain boundary plane after the specimen was fractured in tension in the grain boundary plane. The depth of penetration measured by both methods agreed well. Further details describing these techniques have been reported elsewhere.'p7

Jan 1, 1969

By H. M. Howe

The chief purpose of this note is to call attention to the triaxial diagram as a convenient means of illustrating the properties of slags, and by this example of its use to commend it to those inclined to graphical studies having other possible applications. Explanation.—In the common or di-axial diagram, the properties corresponding to any point are determined by its perpendicular distance from each of two axes. For example, in an ordinary stress-strain diagram the properties of a given point in the curve are, first, a stress cd so many pounds per square inch, because its perpendicular distance from the horizontal axis of the diagram corresponds by the vertical scale to that stress; and second, a strain or elongation of so many per cent., because its perpendicular distance from the vertical axis corresponds by the horizontal scale to that elongation. It happens that, as a matter of convenience, we habitually place these two axes at right angles to each other; so that our measurenieilts happen to be made not only at right-angles to

Jan 1, 1899

IRON AND STEEL COMMITTEE ALBERT SAUVEUR, Chairman .A. A. STEVENSON, Vice-Chairman HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. Guilliaem Aertsen, Robert W. Hunt, .-E: Gybbon Spilsbury, John Birkinbine, J. E. Johnson, Jr., J. S. Unger, William H. Blauvelt, William Kelly, Felix A. Vogel, Charles A. Buck, Charles Kirchhoff, Leonard Waldo, James Gayley, Richard Moldenke, William R. Walker, Henry D. Hibbard, Joseph W. Richards, William R. Webster, Henry M. Howe, C. F. W. Rys, Frederick W. Wood. Manuscripts of the following papers on iron and steel for the February -meeting have been received and accepted: Albert Sauveur, Notes on Heating and Cooling Curves of Professor Carpenter's Electrolytic Iron. H. M. Howe and A. G. Levy, Notes; on the Plastic Deformation of Steel during Overstrain.

Jan 2, 1914

By D. B. Smith, John Chipman

THIS investigation was undertaken as a prerequisite to the study of sulphur activities in the liquid system Fe-Cu-Ni, a continuation of the work of Sherman, Elvander, and Chipman,¹ using the same equipment and the same experimental technique. Temperature measurements are made with a disappearing filament optical pyrometer, sighting through a prism onto the surface of the melt which is heated by induction. To obtain true temperatures by this means, a calibration is necessary, since, in the absence of true black-body conditions, the observed temperature is always lower than the true temperature. This calibration is actually an emissivity correction, since the emissivity is a function of both temperature and melt composition. The original furnace was used with a deeper metal bath to provide sufficient depth of immersion for the thermocouple which was inserted through the sampling hole. The atmosphere was a 50-50 mixture or argon and hydrogen passing through the furnace at a rate of 1000 ml per min, and preheated by means of a molybdenum resistance coil. It was assumed that the rapid gas flow effectively eliminated any error which might have resulted from the presence of metallic vapor. The charge in each case consisted of about 300 g of metal, contained in a high purity, dense alumina crucible. At each melt composition, readings of the optical pyrometer and of a thermocouple immersed in the molten metal were taken simultaneously. Calibration curves of optical vs. true temperature were then made for each melt composition investigated. Thermocouples were made of 0.010 in. platinum and platinum-10 pct rhodium. They were checked against the melting point of chemically pure copper. Silica protection tubes with an outer diameter of approximately 1/8 in. were used. The depth of immersion of the tip in the molten metal was approximately 1 14 in. The life of these small thermocouples was relatively short, varying from approximately 1 min at 1550°C to 10 min or longer at 1300°C. Melts containing iron corroded the protection tubes more than those without iron present. Measurements taken while heating checked those taken while cooling, indicating the absence of a temperature gradient between the molten metal and the thermocouple. Results The temperature range of the. measurements on copper-free metals extended from the melting point to 1600°C. For copper the upper limit was 1380°C, and the data were extrapolated linearly for comparison with observations on the other metals and alloys at 1535°C. Examples of typical calibration curves for various melt compositions are shown in Fig. 1. These curves, besides providing a calibration system for the given experimental conditions, also give a basis for the calculation of true emissivities at the effective wavelength of the pyrometer, 0.65 micron. The starting point of the calculations is the value of the emissivity of iron at its melting point. Taking the melting point of electrolytic iron under hydrogen as 1535°C, and using the corresponding emissivity value of 0.43, as determined by Dastur and Gokcen,² the emissivities can be determined as functions of composition (and temperature, if desired). The relationship used is the Wien equation: ln(Ea)=C2/?(1/T1-1/Ta where E is the emissivity; a, the transmissivity of the optical system; C,, the fundamental constant, 14,380 micron-degrees; A, the wave length of light used (0.65 micron); Tt, the true temperature, OK; and T., the apparent temperature, OK. At the melting point of iron the observed temperature was 1358"; this gives 0.62 for the transmissivity, which compares with 0.65 in the similar system used by Dastur and Gokcen. The emissivities of all the compositions investigated were determined at 1535°C, after obtaining from each calibration curve the corresponding temperature. These results

Jan 1, 1953

By Alexander Squire

ONE of the principal factors that have contributed to the hesitancy of design engineers to use metal-powder parts is the difficulty experienced in the determination of the mechanical properties of compacted components. Because standard test: methods cannot usually be applied in the inspection of such parts, and because adequate special test methods have not been developed, it has been considered desirable to investigate the methods that are applicable. These may then be included in specifications for metal-powder materials' and components in order that the design engineer may be assured that the subject parts possess the desired mechanical properties for satisfactory performance. It is known that direct relationships exist between usually nonmeasurable properties as tensile strength and elongation and shear strength and the angle through which compacts may be plastically deformed before fracturing. These correlations are valuable in the inspection of specific parts, but it is necessary to set up standards before they may be satisfactorily employed. Apart from the use of correlations, the number and character of the inspection methods that are applicable to almost all powder parts is limited to three-chemical analysis, density, and hardness. The last of these may or may' not be a pertinent characteristic, since the indentation hardness of many powdered-metal materials is so low as to have little significance. It is, however, occasionally desirable to use hardness measurements as an indication of the uniformity of the structure of pieces of a given type. Chemical analysis reveals very little about the physical properties of metal-powder compacts, since the unpressed powder is usually of a composition almost identical with that of the finished pieces. Density determinations are simple, to perform and have the advantage of being nondestructive in character. If the dimensions of a machine part are known (and usually they are), the average density may be determined by weighing a given number of pieces and dividing by the calculated volume of the parts. More accurate measurements may be made by the water-displacement method. , It. is recognized that mechanical properties of metal-powder materials are related to their density, but usually these relations are determined for only one type of powder, processed under a given set of conditions. Comparisons of the properties of compacts formed from different types of powders are made on the basis of compacting... pressures instead of density, and for. this reason the results obtained by using powders of different types appear widely variant.

Jan 1, 1947

By Alexander Squire

One of the principal factors that have contributed to the hesitancy of design engineers to use metal-powder parts is the difficulty experienced in the determination of the mechanical properties of compacted components. Because standard test methods cannot usually be applied in the inspection of such parts, and because adequate special test methods have not been developed, it has been considered desirable to investigate the methods that are applicable. These may then be included in specifications for metal-powder materials and components in order that the design engineer may be assured that the subject parts possess the desired mechanical properties for satisfactory performance. It is known that direct relationships exist between usually nonmeasurable properties as tensile strength and elongation and shear strength and the angle through which compacts may be plastically deformed before fracturing. These correlations are valuable in the inspection of specific parts, but it is necessary to set up standards before they may be satisfactorily employed. Apart from the use of correlations, the number and character of the inspection methods that are applicable to almost all powder parts is limited to three—chemical analysis, density, and hardness. The last of these may or may not be a pertinent characteristic, since the indentation hardness of many powdeied-metal materials is so low as to have little significance. It is, however, occasionally desirable to use hardness measurements as an indication of the uniformity of the structure of pieces of a given type. Chemical analysis reveals very little about the physical properties of metal-powder compacts, since the unpressed powder is usually of a composition almost identical with that of the finished pieces. Density determinations are simple to perform and have the advantage of being nondestructive in character. If the dimensions of a machine part are known (and usually they are), the average density may be determined by weighing a given number of pieces and dividing by the calculated volume of the parts. More accurate measurements may be made by the water-displacement method. It is recognized that mechanical properties of metal-powder materials are related to their density, but usually these relations are determined for only one type of powder, processed under a given set of conditions. Comparisons of the pioperties of compacts formed from different types of powders are made on the basis of compacting pressures instead of density, and for this reason the results obtained by using powders of different types appear widely variant.

Jan 1, 1947

By Alexander Squire

One of the principal factors that have contributed to the hesitancy of design engineers to use metal-powder parts is the difficulty experienced in the determination of the mechanical properties of compacted components. Because standard test methods cannot usually be applied in the inspection of such parts, and because adequate special test methods have not been developed, it has been considered desirable to investigate the methods that are applicable. These may then be included in specifications for metal-powder materials and components in order that the design engineer may be assured that the subject parts possess the desired mechanical properties for satisfactory performance. It is known that direct relationships exist between usually nonmeasurable properties as tensile strength and elongation and shear strength and the angle through which compacts may be plastically deformed before fracturing. These correlations are valuable in the inspection of specific parts, but it is necessary to set up standards before they may be satisfactorily employed. Apart from the use of correlations, the number and character of the inspection methods that are applicable to almost all powder parts is limited to three—chemical analysis, density, and hardness. The last of these may or may not be a pertinent characteristic, since the indentation hardness of many powdeied-metal materials is so low as to have little significance. It is, however, occasionally desirable to use hardness measurements as an indication of the uniformity of the structure of pieces of a given type. Chemical analysis reveals very little about the physical properties of metal-powder compacts, since the unpressed powder is usually of a composition almost identical with that of the finished pieces. Density determinations are simple to perform and have the advantage of being nondestructive in character. If the dimensions of a machine part are known (and usually they are), the average density may be determined by weighing a given number of pieces and dividing by the calculated volume of the parts. More accurate measurements may be made by the water-displacement method. It is recognized that mechanical properties of metal-powder materials are related to their density, but usually these relations are determined for only one type of powder, processed under a given set of conditions. Comparisons of the pioperties of compacts formed from different types of powders are made on the basis of compacting pressures instead of density, and for this reason the results obtained by using powders of different types appear widely variant.

Jan 1, 1947

By S. S. Arentz

PLANNED health and safety programs have become an essential part of American industry because such programs lead to increased operating efficiency, improved labor relations, better public relations, and to substantial savings in compensation insurance. Those of you who have had the unpleasant duty of informing the wife or widow of one of your men of his serious injury or death while on the job, know that all the benefits of a successful safety program do not show on the balance S. S. ARENTZ, Member AIME, is General Superintendent, Nevada Operations, Combined Metals Reduction Co., Pioche, Nevada. AIME San Francisco Meeting, February 1949. TP 2741 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Jan. 6, 1949. sheet. These programs are of particular importance to the mining ,industry because mining's reputation as an unusually hazardous industry and the commonly isolated location of mining operations tend to focus attention on these problems. Description of Operations: Before proceeding with a discussion of our health and safety programs at Pioche, it may be proper to give a brief description of Pioche and of our operations there. Pioche is one of the early Nevada mining camps. It was founded shortly after the discovery of high grade silver ore in 1863 and mining has continued with more or less regularity to the present day. In an era of lawlessness, Pioche was notorious. The story persists that 75 men died with their boots on before one died a natural death, and old payroll records show that nearly as many gunmen were employed to stand off claim jumpers as there were miners working the mine. That was probably as close to a safety program as the times permitted. Pioche is situated in southeastern Nevada on the main highway between Ely and Las Vegas. The camp is on the flank of "Treasure Hill," near the original silver discovery, at an elevation of about 6000 ft. The present day population of about 2000 is primarily dependent upon the mines of the area, although Pioche also serves as the county seat of Lincoln Couqty and as the center of the surrounding livestock industry. The camp is served by a branch of the Union Pacific Railroad and receives power from the generators at Hoover Dam. The Pioche operations of the Combined Metals Reduction Co. were started in 1923 when the first complex lead-zinc ore was shipped to the company's mill at Bauer, Utah. The modern mill at Pioche was completed in 1941. The operations are medium sized in the nonferrous field, employing an average of 350 men in the mine, mill, and related works. The complex lead-zinc ore is mined from replacement deposits in a comparatively flat, extensively faulted, limestone horizon. Mining methods vary from stull-supported open stopes to filled square-set stopes. The thin bedded limestone and shale overlying the ore is allowed to cave as areas are mined out and caving frequently follows closely upon ore extraction. The relatively heavy ground and the numerous faults add to the problems of safe mining. The mine is well mechanized and the mill and surface plant are modern and well equipped. Labor is organized in a C.I.O. union and labor-management relations have been unusually harmonious. During most of the period since 1923 a competent supervisory staff worked to reduce safety hazards but the primary responsibility for safety rested on the individual workman. Accidents happened and all too frequently they were regarded by all concerned as unavoidable. In October 1939, the late Robert L. Dean became superintendent at Pioche. Most of his previous experience had been in the fields of iron and coal mining and from that experience he brought the concept that no accident is unavoidable. Many of the features of our present health and safety programs were initiated by Mr. Dean during his term as superintendent. Health Program: Our health program centers in Dr. Q. E. Fortier and his new, well-equipped, and well-staffed, modern hospital in Pioche. The program starts with a thorough pre-employment physical examination and is followed by yearly re-examinations at the expense of the company. The Pioche Mutual Benefit Association, to which all Pioche mine operators and employees belong, pays benefits covering hospitalization and surgery expense incurred by employee members and their families. The Association is governed by a board of directors elected by its members. The mine operators of the district donated the original capital and pay the monthly dues of the employee members. The employees pay the dues covering members of their families. Though not strictly a part of the

Jan 1, 1951

By S. S. Arentz

PLANNED health and safety programs have become an essential part of American industry because such programs lead to increased operating efficiency, improved labor relations, better public relations, and to substantial savings in compensation insurance. Those of you who have had the unpleasant duty of informing the wife or widow of one of your men of his serious injury or death while on the job, know that all the benefits of a successful safety program do not show on the balance S. S. ARENTZ, Member AIME, is General Superintendent, Nevada Operations, Combined Metals Reduction Co., Pioche, Nevada. AIME San Francisco Meeting, February 1949. TP 2741 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Jan. 6, 1949. sheet. These programs are of particular importance to the mining ,industry because mining's reputation as an unusually hazardous industry and the commonly isolated location of mining operations tend to focus attention on these problems. Description of Operations: Before proceeding with a discussion of our health and safety programs at Pioche, it may be proper to give a brief description of Pioche and of our operations there. Pioche is one of the early Nevada mining camps. It was founded shortly after the discovery of high grade silver ore in 1863 and mining has continued with more or less regularity to the present day. In an era of lawlessness, Pioche was notorious. The story persists that 75 men died with their boots on before one died a natural death, and old payroll records show that nearly as many gunmen were employed to stand off claim jumpers as there were miners working the mine. That was probably as close to a safety program as the times permitted. Pioche is situated in southeastern Nevada on the main highway between Ely and Las Vegas. The camp is on the flank of "Treasure Hill," near the original silver discovery, at an elevation of about 6000 ft. The present day population of about 2000 is primarily dependent upon the mines of the area, although Pioche also serves as the county seat of Lincoln Couqty and as the center of the surrounding livestock industry. The camp is served by a branch of the Union Pacific Railroad and receives power from the generators at Hoover Dam. The Pioche operations of the Combined Metals Reduction Co. were started in 1923 when the first complex lead-zinc ore was shipped to the company's mill at Bauer, Utah. The modern mill at Pioche was completed in 1941. The operations are medium sized in the nonferrous field, employing an average of 350 men in the mine, mill, and related works. The complex lead-zinc ore is mined from replacement deposits in a comparatively flat, extensively faulted, limestone horizon. Mining methods vary from stull-supported open stopes to filled square-set stopes. The thin bedded limestone and shale overlying the ore is allowed to cave as areas are mined out and caving frequently follows closely upon ore extraction. The relatively heavy ground and the numerous faults add to the problems of safe mining. The mine is well mechanized and the mill and surface plant are modern and well equipped. Labor is organized in a C.I.O. union and labor-management relations have been unusually harmonious. During most of the period since 1923 a competent supervisory staff worked to reduce safety hazards but the primary responsibility for safety rested on the individual workman. Accidents happened and all too frequently they were regarded by all concerned as unavoidable. In October 1939, the late Robert L. Dean became superintendent at Pioche. Most of his previous experience had been in the fields of iron and coal mining and from that experience he brought the concept that no accident is unavoidable. Many of the features of our present health and safety programs were initiated by Mr. Dean during his term as superintendent. Health Program: Our health program centers in Dr. Q. E. Fortier and his new, well-equipped, and well-staffed, modern hospital in Pioche. The program starts with a thorough pre-employment physical examination and is followed by yearly re-examinations at the expense of the company. The Pioche Mutual Benefit Association, to which all Pioche mine operators and employees belong, pays benefits covering hospitalization and surgery expense incurred by employee members and their families. The Association is governed by a board of directors elected by its members. The mine operators of the district donated the original capital and pay the monthly dues of the employee members. The employees pay the dues covering members of their families. Though not strictly a part of the

Jan 1, 1951

By G. S. Cole, G. F. Bolling

ThE exact type of fluid flow which occurs in a solidifying ingot is important in determining subsequent grain structure. This has been shown in studies of natural Convection" and of forced stirring or other disturbances of the melt."16 We shall explicitly argue that a complement to the existing natural flow in an ingot should be more effective than other types of flow in promoting the columnar-to-equiaxed transition. The ultimate effects of fluid flow upon structure is one of the topics of solidification that we have investigated in the alloy system Pb-Sb, under conditions simulating casting. In Fig. 1, the essential features of a bidirectional growth apparatus are shown; horizontal freezing from water-cooled faces within a low-thermal-conductivity lavite boat is a reasonable simulation of an ingot section. Details such as the furnace and thermocouples are omitted in order to show the location of four permanent. magnets, each with a pole separation of 21 in. providing a central field of about 1000 Gauss. When coupled with a dc current imposed through appropriate connections made at the cooled faces, a flow of fluid is produced as shown schematically. This technique described by Pfann and ~orsi" is ideal for our purpose since the flow indicated is the same as that we observe to occur naturally in this system. Components of 99.999 pct purity were used for study and all due precautions were taken in alloy preparation to avoid contaminants. Sections of the specimens were taken to ensure results representative of the interior as well as the surface of specimens. All proportions of equiaxed and columnar regions were measured by tracing the etched grain structures onto graph paper and simply counting squares. Four alloys were examined at superheats of 40" * 5°C and 100" * 9°C. Preliminary tests had shown that no appreciable enhancement of structure was obtained with magnetic field alone, so that this condition is not reported; it should nevertheless be noted that other configurations of magnetic field will reduce convection and thus enhance columnar growth.'8 For the tests reported the magnetic field was applied to a specimen by bringing the four preassembled magnets to a position 2 mm from an outer tube immediately after the ingot was poured. The dc current of 30 amps passed through the sample throughout the entire solidification cycle, resulting in a power dissipation of 9 w per sq cm of interface. This may be compared to the evolution of latent heat of approximately 18 w per sq cm. Table I contains the results of this experiment in terms of the total area ratio, equiaxed/columnar grains, as a function of the field interactions, solute concentrations, and superheats employed. The total structure of the ingot is seen to be most influenced when both the field and current are applied simultaneously; when current acts separately, little effect may be noted in spite of the heat supplied. In addition, the change in structure from the no field-no current case to the field-current condition is more pronounced at the higher superheat, and the higher the concentration of antimony. An example of the grain refinement, as well as the increased equiaxed zone, is shown in Fig. 2. It is now important to prove that there is indeed an increase in fluid flow due to the presence of the field-current interaction; this is done by temperature measurements in the liquid metal. Let us consider a bidirectional casting in which heat is applied to and removed from the system, in such a way that rate of solidification is zero.* When a sensitive thermocouple

Jan 1, 1967

By Frederick Prime

At the last meeting of the Institute, Mr. A. L. Holley read a paper on "Steel," in which he proposes for it a definition so opposed to the one generally received, as to call for some remarks. Until within the last five or six years there has been no dispute on the subject, and it seems worth while to investigate the matter. For not only does a proper tax on all importations depend on a proper appreciation of the term steel, but it is necessary to know whether steel, or wroughtiron, or homogeneous iron are requisite in all processes of manufacture in which malleable iron is employed, on accouut of cost, strength, etc. Karsten* says: "Iron may be obtained, either as an unforgeable, unweldable metal, which melts at a high heat, termed cast-iron ; or as a ductile, weldable, soft, metal, which can only be melted at the

By J. J. Friel, E. S. Erickson

Dolomite-fluxed pellets of various compositions were made from magnetite concentrate, hematite concentrate and a concentrate containing a natural mixture of both. Physical properties and reduction test results were used to ascertain proper compositions and firing temperatures. These pellets were subjected to physical tests and to reduction tests. Petrographic and electron microprobe examinations were made to evaluate the effect of composition and fining on the phase assemblage. We interpreted our test results in terms of chemistry and microstructure and related these to properties. This approach enabled w to determine the composition best suited to each of the three concentrates. Compared with acid pellets, dolomite- fluxed pellets of the optimum compositions had similar physical properties but swelled less, softened at a higher temperature, and reduced faster and more completely.

Jan 1, 1983