Search Documents

By Clarence Zener

THEORETICAL considerations by one of the authors have led1 to the prediction that the dynamic internal friction of annealed metals has a broad maximum at a certain grain size. This prediction they have veri-fied2 for alpha brass. In the present paper the theory is extended to include the precise manner in which the internal friction varies with grain size on either side of the maximum. New experimental data are pre¬sented to test this extended theory. The physical basis for the type of internal friction that is being investi-gated lies in the interplay between stress and temperature. Just as local fluctuations in temperature give rise to local fluctuations in stress, so like-wise fluctuations in stress give rise to fluctuations in temperature. But temperature gradients give rise to necessarily irreversible thermal cur-rents, and hence to internal friction. The theory for this type of internal friction has been developed quantitatively,3 and has been experimentally verified,4,5 for the particularly simple case of the transverse thermal cur-rents accompanying transverse vibrations. Of more fundamental impor-tance are the intercrystalline thermal currents accompanying all types of vibration. The variation in stress across grain boundaries arises from the elastic anisotropy and at least partial random orientation of the individual crystallites. An exact quantitative treatment of the internal friction due to these thermal currents is of course out of the question. However, much information can be obtained from general arguments.1,6 Thus when the frequency of vibration f is low, or when the grain size d is small, adja-cent grains remain nearly in thermal equilibrium, and vibration proceeds isothermally with little internal friction. Again, when the frequency is high, or the grain size large, the heat flow per cycle is small, the vibration proceeds adiabatically with little internal friction. The internal friction will become a maximum in the transition region. The degree of adiabatic-

Jan 1, 1940

By G. A. Colligan, G. L. F. Powell

A new experimental technique has been developed to study nucleation behavior in eutectic alloys. It is somewhat similar to that applied by Sundquist and Mondolfo1 but with the advantages that: 1) bulk samples are undercooled instead of small droplets thus allowing the thermal behavior to be monitored by a thermocouple immersed in the sample, and 2) nucleation behavior is investigated in the same sample on either side of the eutectic composition by adding additional component to the sample under controlled conditions which preclude the addition of nu-cleation contaminants. Sundquist and Mondolfo carried out ]nucleation ex-periments on a large number of eutectic alloy sys-tems and concluded that nonreciprocal nucleation operated. If one phase a was a good nucleant for the other phase 0, then B was a poor nucleant for a. This was determined experinlentally by comparing the nucleation temperatures of 100 to 300 u diameter droplets of hypereutectic and hypoeutectic composition cooled from above the liquidus and from a temperature between the liquidus and the eutectic temperature. Primary phase a was concluded to be an efficient nucleant for the other phase B, if the following experimental result was obtained. Referring to Fig. 1, the temperature TI at which a drop of hypereutectic alloy of composition B froze when cooled from above the B liquidus was noted. This was the nucleation temperature for B in the absence of a. A drop of hypoeutectic alloy of composition A was then frozen from temperature T2 between the a liquidus and the eutectic temperature. The temperature T3 at which the eutectic nucleated in the presence of the primary or proeutec-tic a was noted. If this temperature T3 was higher than the temperature TI at which the B nucleated in a hypereutectic alloy, it was concluded that the primary a had nucleated the 6. This temperature T3, representing a certain undercooling below the equilibrium eutectic temperature Te , was designated ?TB by a> the undercooling below T, for nucleation of 13 by a. If there was no substantial difference in nucleation temperature between the hypereutectic drop cooled from above the /3 liquidus and the hypo-eutectic drop cooled from a temperature between the a liquidus and the eutectic temperature, it was considered that the a nucleated B at an undercooling equal to or greater than that at which P nucleated from a hypereutectic alloy. Sundquist and Mondolfo1 found that faceted primary crystals were good nucle-ants for metals that grow as orthogonal dendrites when present as the primary phase. Jackson2 has questioned Sundquist and Mondolfo's technique and proposed that in Sundquist and Mon-dolfo's samples, such as composition A, primary a retained B in reentrant grooves at their surfaces when heated to a temperature above the eutectic but below the a liquidus. This objection was suggested by experiments with organic eutectics where reten-

Jan 1, 1970

By P. J. Jacquard, C. Jain

Interpreting pressure measurements is one of the fundamental problems in the operation of oil reservoirs. The principal methods and means of study zuhich are currently used are reviewed. Emphasis is placed on the necessity of improving the quality of the information to turn it to the best possible account. One of the important aspects of the problem is the development of a system of automatic interpretation of the pressure measurements. The proposed method aims at this objective: starting from the relation which exists between a local perturbation of permeability and its effect on the velocity potentials in the wells, we determine by successive approximation the modifications to be made to the permeability map by fitting the least squares between the measured pressures and the pressures indicated by the mathematical model. The method has already been successfully employed in the case of heterogeneous reservoirs of radial- circular symmetry. Its application is extended here to the two-dimensional case, and is illustrated by two examples, for which the results are presented. The conditions required for the method to become fully operational are likewise analyzed. I — INTRODUCTION One of the basic problems of production and recovery from oil fields is interpreting pressure measurements made in wells in the single-fluid-phase regime. Simplifying assumptions, for example supposing the reservoir to be homogeneous, make it possible to use more or less simple methods which permit the estimation, from these pressure measurements, of a mean value of the permeability around the wells. Considering the actual heterogeneity of the majority of reservoirs, and the phenomena of interference between wells, these methods are only indicative. Much has been published on the studies of different cases of comparatively simple heterogeneity: some have discussed the radial heterogeneity around a single wel1,l or vertical heterogeneity.2 The results of these works have shown the influence of variations of permeability on the pressure, but unfortunately they are not very useful in practice because they all are concerned with the phenomena around a single well, without interference between wells, and they correspond to relatively simple and theoretical schemes. These studies of reservoirs or parts of reservoirs on a larger scale are made by the electric analyzer or digital model. We define a permeability map and a porosity map, then reproduce the production history of the wells on the wells of the model, and note the corresponding pressures. These pressures are then compared with actuality, and the discrepancies observed are analyzed. From this analysis we deduce the modifications to be made to the maps of permeability and porosity, and repeat until the coincidence between the pressures indicated by the model and the actually observed pressures is considered adequate. We have adjusted the model. Obviously, in this method of investigation, everything depends on the formula which permits the modification of the permeability to approach the adjustment. Considering the complicated nature of the problem, some oversimplified formulas are poorly adapted to reaching a good adjustment. For example, we have shown that the elementary operation of increasing the permeability not far from a producing well to compensate for too low pressures in the well can, in certain cases, express itself by an effect exactly opposite. 3 The project described here is for a system where we begin with the pressure measurements and the several known parameters of the reservoir, and develop the most probable permeability map, taking account of the measurements available and a subdivision of the reservoir fixed a priori. Ideally, this system is conceived as one in which no manual intervention would be necessary. The model simulating the reservoir is only one part of the whole system, and it is neither the longest nor the most complex part. The need to integrate the model into an aggregate of much more extensive processes has led to the adoption of the digital solution, even though a solution combining the digital and the analog is perfectly conceivable. The simulating model is in that case no more

Jan 1, 1966

By B. Paul, C. C. Fu

Experiments indicate that the fatigue limit of various drill steels becomes vanishingly small in the presence of water and other corrosive liquids. Therefore one must generally expect fatigue failures of drill steels in a great many field operations. However, it is theoretically possible to so choose the hammer impact speed of a percussion drill in order to maximize the total length of hole drilled before failure occurs. In this paper the existence of an optimum speed is demonstrated and it is shown to be comparable to presently used piston speeds. The influence on drilling speed and hole length of a number of other pertinent design features, such as bit geometry, hammer geometry and steel properties is also established. Although machinery should be designed to obtain optimum performance, it is not always clear just what performance characteristic is to be optimized. For example in a rock drill it would be desirable to optimize all of the following characteristics: drilling speed, bit life, steel life, total length of hole drilled before failure, and efficiency of energy conversion. The word failure could signify excessive bit wear, bit fracture, steel fracture, or some other type of component failure. It is not possible in general to optimize all performance criteria simultaneously. For example, one could achieve fantastically large drilling rates at the expense of bit or steel life, energy requirements and physical size of system. It therefore becomes necessary to compromise requirements in order to achieve a well-balanced albeit non-optimum design. It is, however, extremely useful to explore the interrelationships between the different performance characteristics. Such a procedure would help to establish theoretical limits of performance within the framework of existing knowledge and also serve as a practical design procedure for special applications where a particular performance characteristic is of greatest concern to the user (e.g., steel breakage might be especially undesirable in certain locations). It is the purpose of this paper to examine the problem of how one may drill the deepest possible hole before breakage of the drill steel occurs. Of course the problem is almost trivial if a well defined fatigue limit (endurance limit) exists for the drill steel. In such cases one merely keeps the piston impact speed sufficiently low to insure that the stresses in the steel never exceed the fatigue limit, thereby achieving an infinite life. If, however, no definite fatigue limit exists, as seems to be the case in the presence of even mildly corrosive agents such as water (see later discussion), then a finite life is inescapable and one can at best hope to maximize the useful life of the system. Indeed it will be shown that the system life is related to drilling speed in the manner shown schematically in Fig. 1-a. Even if a definite fatigue

Jan 1, 1965

J. M. Wadsworth,' Okmulgee, Okla. (written discussion).—It seems to me that thc young man must first be absolutely sure that the work he has taken up is to his liking and then I would advise that he get into the practical end of it and learn as much about it as he can as fast as he can. For instance, in the refinery business the college man, graduated in chemical engineering, should ground himself by going through the various departments in a refinery and working in them until he is thoroughly familiar with the operating problems. In a short time he would be able to apply many things which appear in the abstract form in his college work and this would opcn up an opportunity for him to capitalize on them, promoting his own interest. I do not criticize the present-day college men as a class, but I have found that many of them come into your plant with the idea that mere possession of a diploma should insure rapid promotion; in a short time they are impatient and usually leave. We have found in employing men that the single attribute most difficult to find in them is a lot of energy and whole-hearted interest in the work at hand, and it seems to me that if a man combines these with a careful technical training he should be fairly well equipped to gamble on his future. They must learn that the biggest satisfaction to be gained in life is in their work. Procedure for Attaining Objective of Young Petroleum Engineer H. B. Fell,+ Ardmore, Okla. (written discussion).—Of course, the first thing to be ronsidered in any proposition is the ultimate objective that is desired to be attained. 1 presume that the desired objective of most of the young men graduating in petroleum engineering will be that of chief executive of one of the companies in the petroleum industry, or one of the allied industries, or to become an independent oil producer, or oil refiner, or possibly an oil distributor. The next phase then to be considered is the procedure which should most logically be followed to attain the objeckive of the indivitlual, since in these cases these young men will have been trained in a course in petroleum engineering and it would logically be presumed that the attainment of their objective should be through the operating end of the branch of the business with which they are connected. The operating end is, of course, the department of each branch of the business that develops the resources, or refines the products, or distributes the products, from which the profits are derived, and is a part of any business which is filled with enough interesting work to appease the desires of the most ambitious young men. In order to get the best possible training it would appear to me that the place for a young man to start after graduation would be at the bottom of that branch of the industry which he expects to follow. For example, if he is going in the producing end he can gct no better training than is secured by starting as a roustabout in the ficltl, where he romes in constant rontact with the character of work that is necessary

Jan 1, 1928

By George A. Komadina

From its modest beginning in 1957 with one mill grinding section handling 3000 tpd Pima has steadily expanded. In July 1966, work was completed that allowed the concentrator to treat in excess of 18,000 tpd. Almost immediately Pima embarked on another expansion program that will increase plant capacity to 30,000 tpd during the summer of 1967. This repeated expansion has corresponded with the development of additional low-grade ore deposits and with the improved operating economics realized by handling larger masses of material. Early in the life of Pima it was known that a mineralized area was present on the flanks of the high-grade orebody which systematic drilling had shown to be a low-grade copper orebody. Many months of engineering studies revealed that this was sufficient to allow Pima to compete with other large scale, low-grade copper operations in the Southwest.

Jan 11, 1967

By C. C. Henning

IN any line of human activity logical handling requires an amount of attention to each phase that is in keeping with the importance of that phase. In the complex and rapidly changing field of modern ferrous metallurgy it is difficult to allot the proper degree of attention to the various subjects, and it is not surprising that one or more subjects of major importance should for a time be neglected. Bessemer steel is a good example of a neglected subject. It is largely taken for granted, inferior physical quality is assumed for it, and there is a lack of interest in its technical development and commercial application. Availability of supply is limited. In spite of this technical indifference, limited source and lack of commercial exploitation, bessemer steel con-stitutes a large volume of tonnage in daily use. There is a fairly prev-alent idea even among technical people that bessemer steel survives mostly because of low cost and by reason of a dwindling residue of applica-tions sufficiently common to permit of its use. The difference in cost between bessemer and open-hearth steel is governed largely by the relative cost of manufacture of pig iron and the market price of steel scrap. During the past four years there have been long periods of time during which the price of steel scrap was low enough so that open-hearth steel was considerably lower in manufacturing cost than bessemer. As to application, it may be pointed out that thousands of tons of this material in the form of bessemer screw steel are applied for moving parts in automotive and other equipment. Some forging work and considerable heat treating, particularly carburizing, is performed on this grade.

Jan 1, 1935

By K. L. Moazed, G. M. Pound

An investigation was made of the deposition of silver from a thermal beam onto tungsten field-emitter tips at 300°K. "Island"-type nuclei were observed to form and grow. The nucleation of silver crystals occurs preferentially on non-close -packed planes of a tungsten tip at a critical volume free-energy change of about —2900 cal per cc. The adatom population which is critical for appreciable nucleation rate of silver crystals is about 0.2 of a monolayer and is essentially independent of beam flux, time, and source temperature. This result is strong evidence that a metastable equilibrium exists between adatoms and critical nuclei, as assumed in the present theory. SOME of the more significant studies of nucleation in deposition of metals from vapor beams have been conducted by measuring the thermal beam flux which is critical for appreciable rate of nucleation on a substrate surface held at a given temperature.'2 The observed critical supersaturations may be described in terms of Eq. [7] which was derived3'3a on the model of an adsorption, surface migration, and statistical fluctuation mechanism. However there usually made with a low-power optical microscope, a fairly insensitive method of detection. The object of the present study was to overcome some of these difficulties by measuring the critical supersaturation for condensation of a thermal beam of silver onto a tungsten field-emitter tip. Such a tip may be cleaned by electrically heating it to a high temperature in situ, and the high vacuum obtainable in a field-emission tube (10-10 torr) precludes adsorption of residual gases for convenient periods of time. Furthermore, the degree of cleanliness, the orientation, and the state of imperfection of the tip may be ascertained from the field-emission pattern. Detailed explanations of theoretical considerations and experimental procedures relating to the field-emission microscope may be found in a number of excellent review articles12'13 and thus only a brief description will be given here. The electronic work function of a metal is defined as the energy that an electron needs to escape from the potential field of the solid. By applying a large field between the surface of the solid and a suitable collector, it is possible to free the electrons by the tunnel effect. Fields of approximately 30 million v per cm are needed to produce this effect, and such fields are obtained in practice by using microscopic surfaces of high curvature (tips). Because the work function of a metal is a function of surface orientation, the emission from the various planes is different, and thus it is possible to obtain a representation of the surface in the emission microscope. In general, the work function is higher for the more densely packed planes. Fig. 1 shows a pattern for "clean" tungsten in which the central dark region represents the (110)

Jan 1, 1964

By G. T. Hahn

On the basis of the recommendation of Lovell, Vogel, and Wernick,&apos; Fry&apos;s reagent*2 was recently c) if decoration of the dislocations by carbon or nitrogen atoms is a factor in the etch pitting. Experiments were performed with samples of a commercial 1020 steel, a vacuum-melted iron (C - 10 to 15 ppm, 0 - 20 to 50 ppm, N < 2 ppm), both annealed 4 hr at 1100°C, and a zone-refined iron (C - 3 to 5 ppm, 0 - 10 ppm, N < 1 ppm ) in the as-cast condition. Saomple surfaces were prepared by grinding to 600A grit and electropolishing. Initially, effects of etching the steel with modifications of the basic Fry composition were examined. It was found that increasing the alcohol or HC1 concentratior~ retarded dislocation pitting; reducing the acid content promoted secondary pitting. Cooling the reagent and the sample did not improve the quality of the etch pits. Best results were obtained with freshly prepared reagent modified by increasing the CuC12 content to 15 g. This composition was used in subsequent experiments. Annealed samples were etched 10 to 15 sec; cold-worked samples —2 to 5 sec.

Jan 1, 1962

Organization Place Date 1919 National Drainage Congress St. Louis, Mo. Nov. 11-13 American Mining Congress St. Louis, Mo. Nov. 1.7-21 Canadian Mining Institute Vancouver, B. C. Nov.. 26-28 American Society of Mechanical Engineers:.... New York, N. Y. Dec. 2-5 American Institute of Chemical Engineers Savannah, Ga. Dec. 3-6 Geological Society of America...; Boston, Mass. Dec. 29-31. American Society of Heating and Ventilating 1920 Engineers New York, N. Y. Jan. Mining and Metallurgical Society of America ... New York, N. Y. Jan. 13. American Institute of Min. and Met. Engineers... New York, N. Y. Feb. 16-19 American Ceramic Society Philadelphia, Pa. Feb. 23-26

Jan 11, 1919

By S. F. Ravitz

IN his excellent book on the Principles of Flotation, Wark&apos; makes the following significant statement concerning the theory of flotation: Two questions of first-rate importance must be considered . . . First, it must be decided whether the sulfide minerals require a collector in order that they may float, or whether as has been claimed, they possess an inherent floatability and need no collector. Second, it must be decided whether the xanthate type of collector can react with or be adsorbed by the unchanged sulfide minerals themselves, or whether, as many claim, reaction with the collector is dependent upon initial oxidation of the mineral surface. In the theory of flotation there are no two questions of greater importance than these. Ravitz and Porter&apos; presented evidence that galena can be floated without a collector, and even without any reagent, provided oxidation products are thoroughly removed from its surface. They found also that thoroughly cleaned galena floated faster when xanthate was used than when a frother alone or no reagent was used, and that, without a collector, the recovery decreased gradually upon exposure of the mineral to air. Their work, however, has met with considerable criticism. I(127).3-6 This paper is presented to answer the objections that have been raised, and to present additional data that confirm their results. EXPERIMENTAL PROCEDURE The apparatus used to provide oxygen-free conditions for flotation has been described in detail by Ravitz and Porter. An atmosphere of purified nitrogen was maintained within the apparatus; all water and solutions used were freed of dissolved air, and could be transferred where desired by the use of nitrogen pressure; nitrogen was used as the gaseous medium for flotation. The flotation cell was essentially a glass cylinder 15 cm. long and 4.6 cm. in diameter. Near the bottom was sealed a fritted glass filter, which broke up the gas into small bubbles, and 6 cm. above this filter was a side arm through which the froth overflowed. The pulp was agitated by a glass impeller, which entered the cell through a mercury seal. For each test 17 grams of galena and 75 ml. of water were placed in the cell, after which the speed of the impeller and the rate of gas flow were adjusted. Water was added gradually during the test to keep the froth level at the proper height. The mineral was prepared and cleaned in the following manner. Exceptionally pure galena was crushed by hand on a clean bucking board, screened to - 150+ 200 mesh, and deslimed on a zoo-mesh sieve with a fine spray of water. It was then boiled on a hot plate for a number of hours with several changes of the desired cleaning solution, after which both the solution and the mineral were placed in the "mineral flask" of the apparatus. The cleaning solution was drained off, and the mineral was boiled with oxygen-free water

Jan 1, 1940

By S. F. Ravitz

In his excellent book on the Principles of Flotation, Warkl makes the following significant statement concerning the theory of flotation: Two questions of first-rate importance must be considered . . . First, it must be decided whether the sulfide minerals require a collector in order that they may float, or whether as has been claimed, they possess an inherent float-ability and need no collector. Second, it must be decided whether the xanthate type of collector can react with or be adsorbed by the unchanged sulfide minerals themselves, or whether, as many claim, reaction with the collector is dependent upon initial oxidation of the mineral surface. In the theory of flotation there are no two questions of greater importance than these. Ravitz and Porter2 presented evidence that galena can be floated without a collector, and even without any reagent, provided oxidation products are thoroughly removed from its surface. They found also that thoroughly cleaned galena floated faster when xanthate was used than when a frother alone or no reagent was used, and that, without a collector, the recovery decreased gradually upon exposure of the mineral to air. Their work, however, has met with considerable criticism.l(127).3-6 This paper is presented to answer the objections that have been raised, and to present additional data that confirin their results. The apparatus used to provide oxygen-free conditions for flotation has been described in detail by Ravitz and Porter. An atmosphere of purified nitrogen was maintained within the apparatus; all water and solutions used were freed of dissolved air, and could be transferred where desired by the use of nitrogen Pressure; nitrogen was used as the gaseous medium for flotation. The flotation cell was essentially a glass cylinder 15 cm. long and 4.6 cm. in diameter. Near the bottom was sealed a fritted glass filter, which broke up the gas into small bubbles, and 6 cm. above this filter was a side arm through which the froth overflowed. The pulp was agitated by a glass impeller, which entered the cell through a mercury seal. For each test 17 grams of galena and 75 ml. of water were placed in the cell, after which the speed of the impeller and the rate of gas flow were adjusted. Water was added gradually during the test to keep the froth level at the proper height. The mineral was prepared and cleaned in the following manner. Exceptionally Pure galena was crushed by hand on a clean bucking board, screened to —I50+ 200 mesh, and deslimed on a 200-mesh sieve with a fine spray of water. It was then boiled on a hot plate for a number of hours with several changes of the desired cleaning solution, after which both the solution and the mineral were placed in the "mineral flask" of the apparatus. The cleaning solution was drained off, and the mineral was boiled with oxygen-free water

Jan 1, 1943

By S. F. Ravitz

In his excellent book on the Principles of Flotation, Warkl makes the following significant statement concerning the theory of flotation: Two questions of first-rate importance must be considered . . . First, it must be decided whether the sulfide minerals require a collector in order that they may float, or whether as has been claimed, they possess an inherent float-ability and need no collector. Second, it must be decided whether the xanthate type of collector can react with or be adsorbed by the unchanged sulfide minerals themselves, or whether, as many claim, reaction with the collector is dependent upon initial oxidation of the mineral surface. In the theory of flotation there are no two questions of greater importance than these. Ravitz and Porter2 presented evidence that galena can be floated without a collector, and even without any reagent, provided oxidation products are thoroughly removed from its surface. They found also that thoroughly cleaned galena floated faster when xanthate was used than when a frother alone or no reagent was used, and that, without a collector, the recovery decreased gradually upon exposure of the mineral to air. Their work, however, has met with considerable criticism.l(127).3-6 This paper is presented to answer the objections that have been raised, and to present additional data that confirin their results. The apparatus used to provide oxygen-free conditions for flotation has been described in detail by Ravitz and Porter. An atmosphere of purified nitrogen was maintained within the apparatus; all water and solutions used were freed of dissolved air, and could be transferred where desired by the use of nitrogen Pressure; nitrogen was used as the gaseous medium for flotation. The flotation cell was essentially a glass cylinder 15 cm. long and 4.6 cm. in diameter. Near the bottom was sealed a fritted glass filter, which broke up the gas into small bubbles, and 6 cm. above this filter was a side arm through which the froth overflowed. The pulp was agitated by a glass impeller, which entered the cell through a mercury seal. For each test 17 grams of galena and 75 ml. of water were placed in the cell, after which the speed of the impeller and the rate of gas flow were adjusted. Water was added gradually during the test to keep the froth level at the proper height. The mineral was prepared and cleaned in the following manner. Exceptionally Pure galena was crushed by hand on a clean bucking board, screened to —I50+ 200 mesh, and deslimed on a 200-mesh sieve with a fine spray of water. It was then boiled on a hot plate for a number of hours with several changes of the desired cleaning solution, after which both the solution and the mineral were placed in the "mineral flask" of the apparatus. The cleaning solution was drained off, and the mineral was boiled with oxygen-free water

Jan 1, 1943

By G. Birkbeck, T. C. Wells

Pearlite morphology in three commercially produced, low-carbon steels has been studied using optical and electron microscopy. A reduction in the cooling rate from 600° to 6°C per hr increased the interlamellar spacing but had little effect on pearlite content. The form of the lamellae was also assessed in terms of a new parameter, the ratio of lamellae length to interhmellar spacing. The variation of this parameter with cooling rate depended on steel composition. For each steel, it would appear that an optimum cooling rate exists at which lamellar pearlite can be produced to the greatest extent, though not necessarily the same extent in different steels. PeARLITE morphology depends principally on steel composition, prior austenite grain size, and either cooling rate or isothermal transformation temperature. Alloying with manganese,&apos;" fine grain size,374 and slow cooling rates reduce the likelihood that a well-developed lamellar structure will be produced. Instead, imperfect structures usually consisting of partly globular carbides are formed in a ferrite matrix. Such structures have been described as granular.1,2,5 degenerate,6 or semi4-pearlite. Manganese additions also progressively lower the eutectoid temperature and the carbon concentration at the eutectoid so so that, for a given carbon content. the pearlite fraction is increased as manganese is added. While the effects of manganese are understood in a general way, quantitative studies of pearlite morphology have been carried out mainly on steels of eutectoid composition;9 little quantitative data is available for low-carbon steels. Certain anomalies exist in the behavior of steels containing -1.5 pct Mn, however. The pearlite morphology in niobium-treated steel differs from that which is generally accepted as typical of low-carbon/manganese steels in that a reasonably well developed lamellar structure is sometimes observed. In the present work, the effects of changes in cooling rate from 600° to 6°C per hr on the pearlite morphology in three commercially produced, low-carbon steels have been studied by both optical and electron microscopy. I) MATERIALS The steels were of the following types: 1) 0.1 pct C, 0.4 pct Mn steel (En 2, a composition similar to specification SAE 1010); 2) niobium-treated, 0.2 pct C, 1 1/2 pct Mn steel (BS 968:1962); 3) silicon-killed 0.2 pct C, 1 1/2 pct Mn steel (En 144, a composition similar to SAE 1320). The chemical analysis for each steel is given in Table I. To facilitate the comparison of pearlite morphology in the three steels, steels 1 and 3 (which were obtained as 1/2-in. plate and 1-in.-diam bar, respectively) were hot-rolled in the laboratory to $ in. thickness, finishing at around 850°C. The BS 968:1962 was received as 1/8-in. plate finished at 885°C and was not further worked. Specimens from each steel were heat-treated in vacuo at 950°C for 1 hr and cooled at rates of 600°, 60°, and 6°C per hr. 11) EXPERIMENTAL Pearlite contents were determined by point counting (500 points) on longitudinal sections mechanically polished and etched in 2 pct nital. Pearlite morphology is usually considered in terms of interlamellar spacing. For pearlite colonies randomly distributed in space and having a true, constant interlamellar spacing So Pellissier et al.9 determined the distribution curve for the apparent spacings of the lamellae on a random section plane. The areal fraction fs of the pearlite colonies occupied by apparent spacings up to a limiting value S is given by:

Jan 1, 1969

By E. L. Kamen, H. D. Kessler, M. Hansen, D. J. McPherson

The highly reactive Ti-Mo and Ti-Cb alloys were prepared and heat treated under protective conditions. Phase diagrams were established based on micrographic and X-ray diffraction analysis and detection of incipient melting. ß titanium forms a continuous series of solid solutions with both molybdenum and columbium, whereas these metals are only slightly soluble in the a titanium modification. PREVIOUS work on the Ti-Mo and Ti-Cb systems was very limited and is discussed in succeeding sections of this paper relating to the respective phase diagrams. The diagrams in the present work were determined principally by micrographic analysis, because other methods such as thermal analysis and dilatometry are not suitable, due to the low diffusion rates of these alloys in the transformation range. X-ray analysis was believed less useful than micrographic analysis because: 1—On quenching certain high titanium alloys from above their transformation range, the body-centered cubic ß phase decomposes into acicular a (hexagonal close-packed) which room temperature X-ray diffraction techniques cannot differentiate from isothermal a. 2— High temperature X-ray techniques might be used, but are difficult to apply and are subject to error because of the high reactivity of titanium with gases such as oxygen and nitrogen. Although metallo-graphic study was the basic method used, X-ray diffraction analysis was applied to a limited extent, to further substantiate the findings. The transformation ranges on the titanium side of the Ti-Cb and Ti-Mo systems were studied both with DuPont Process A (magnesium-reduced) titanium alloys and with iodide titanium alloys. The Process A metal was used chiefly to bracket the transformation range in order to reduce the number of alloys given a particular treatment for the more accurate final study with iodide titanium alloys. Experimental Procedure The analyses of the metals used in the preparation of alloys for this study are presented in Table I. Melting Practice: Early in the work, a consumable electrode, arc melting furnace was used in the preparation of the Process A Ti-base Mo and Cb alloys. This type of furnace has been described by other investigators.&apos;, &apos; One of the major difficulties of the consumable electrode melting process was the prep- aration of homogeneous electrodes (with the mixture of coarse titanium sponge and fine powder alloying addition) which would give homogeneous ingots. Composition gradients encountered may have been due to a tendency for powdered alloying metals to drop away from the electrode in handling. This difficulty in the preparation of homogeneous alloys was overcome by the use of a nonconsumable electrode furnace for later work. This furnace is similar to the one used by Mc-Pherson and Fontana a Ohio State University. A diagram of the nonconsumable electrode arc furnace is given elsewhere.&apos; The source of power was a 400 amp dc welding generator. Electrode tips of tungsten (% in. in diam) were used for all columbium melts and for a limited number of molybdenum melts. Molybdenum tips were used for the majority of molybdenum alloy melts. Columbium tipped electrodes were tried, but disintegrated rapidly at currents above 300 amp. In the Process A titanium melting practice the metals were charged into the water-cooled spun copper crucible in the following forms: l—titanium: sponge (—4 + 16 mesh); 2—molybdenum: sections of 0.003 in. sheet (approximately ½ in. sq); and 3— columbium: powder compacts (? in. lumps broken from large section). After alternately evacuating and purging the furnace several times with argon or helium, the arc was struck against the metal charge,

Jan 1, 1952

By G. Sachs, L. J. Ebert, W. F. Brown

INTRODUCTION ISOTHERMAL transformation, or "austempering," of a carbon-containing austenite at elevated temperatures yields so-called "intermediate products." Their structure and properties are, for a given hardness, rather different from those of "tempered martensite" obtained on conventional quenching and tempering.1 Several investigators2,3 have found that for high carbon and slightly alloyed steels the intermediate products formed at temperatures close to that of the martensite reaction possess strength properties superior to those of tempered martensite. The structure of these low temperature, intermediate products is generally acicular (bainite) but clearly different from that of martensite. However, at higher austempering temperatures, between 1000 and 1300°F (540 and 700°C) carbon steels were found to exhibit a rather low ductility.4-5 Thus notch bar tensile tests showed the ratio between notch strength and regular tensile strength to decrease with increasing austempering temperature. For ductilities below a few percent this notch strength ratio is a measure of ductility, according to investigations on low alloy steels.6-7 Furthermore the presence of intermediate products formed unintentionally on quenching was considered as responsible for the low ductility and impact energy of some heat treated steels.8 These intermediate products could result from partial transformation at the so-called "nose-temperature" where the rate of the transformation is a maximum. Tempering improved such mixtures of martensite and intermediate products, their properties approaching those of tempered martensite of equal hardness. The following investigation constitutes an attempt to determine certain strength properties of a partially austempered and subsequently quenched low alloy steel, namely, a chromium steel (SAE 5140). The structures formed by such a treatment should consist of a mixture of intermediate products formed on austempering and a martensite formed on oil quenching from the austempering temperature. It was intended, by varying the austempering time, to vary the quantity of the intermediate products between zero and 100 pct. The austempering temperature of 860°F was selected after extensive preliminary tests close to the nose-temperature. Austempering at this temperature yielded an acicular intermediate product. Additional tests under less exacting conditions were made for an austempering temperature of 950°F where the intermediate product appeared to be very fine pearlite. To determine the effects of tempering on structures containing various amounts of

Jan 1, 1948

Discussion * of the paper of H. M. Chance, presented at the butte meeting, august, 1913, and printed in bulletin No. 79, July, 1913, pp. 1315 to 1341. George H. Ashley,+ Washington, d. C.:-Mr. Chance&apos;s long practical experience in reporting on coal lands admirably fits him for a discussion of the value of such lands. On behalf of the government geologists, I wish to express my appreciation of Mr. Chance&apos;s friendly, constructive criticism of the government method of valuing coal land in the first part of his paper and, at the same time, to reply to some queries he makes. All admit that coal has no " intrinsic "-monetary value, in the sense that a pound of coal of certain chemical and physical characters is worth " intrinsically " so many cents or fractions of a cent. The term has, however, been found very useful as including those natural factors of coal value, among which are its position and location in the earth, that affect its sale price in contrast with the other cost elements involved in the labor and capital necessary in mining, preparing, transporting, and selling the coal (extrinsic factors). Mr. Chance, while recognizing the " dual origin of value," does not offer any better terms. The survey agrees with Mr. Chance in his definition of coal conservation, that it means the fuller utilization of the heat contents of the coal, and the more complete recovery of the coal from the ground. Coal land withdrawals have not been made to keep such lands off the market, but to prevent their acquisition as non-coal lands before they could be classified so as to be disposed of under the proper law. Nor has the pricing of the more valuable coal lands above the minimum been to raise money for the reclamation fund, to which the money goes, but primarily to discourage the alienation, for holding or speculation, of coal lands not intended or needed for development, and, secondarily, to secure to the people the ?unearned increment," which they are certain in any case to be charged.

Jan 11, 1913

By R. C. Rastogi, F. F. Aplan

The goal of this study is to evaluate the coal flotation process and the interaction of the chemical (reagent) and hydrodynamic (machine, operational) variables as they affect yield, flotation of various sized particles, and sulfur and ash rejection. Coal flotation is found to follow a first order process with the coal floating much faster than either pyrite or ash. This circumstance may be used to achieve gangue rejection during flotation. When floated with MZBC, cresol, or pine oil frothers, coal floats in the size sequence: 108 pm ( - 65 mesh), 589 x 808 pm (88 x 65 mesh), and 1.17 mm x: 589 pm (14 x 18 mesh). However with a substantial amount of fuel oil collector, all particles tend to float roughly in proportion to their content in the feed. An increasing aeration rate was found to be the most important variable in increasing the coal flotation rate. This increase in flotation rate, unfortunately, is also accompanied by an increase in the flotation rate of the pyrite. The rejection of pyrite during coal flotation is best accomplished at low aeration rates, low frother concentrations, and low impeller speeds.

Jan 1, 1986

By V. F. Swanson

At the AIME meeting in Tampa in Oct. 1966, an empirically developed equation was presented which allowed the calculation of free settling velocity for any sized particle: 1 [ ] This equation requires the use of two parameters a and p which are coefficients derived from boundary layer theory.2 It was possible to develop values of a and p for several minerals by back calculation of published data. The original equation had one major flaw. When the fluid density exceeds the density of the solids, the solution to the equation becomes imaginary. A flaw was indicated also by the fact that galena and sylvite both having cubic cleavage, did not have similar values for a and b. Galena gave calculated values of a = 1.082 and g = 3.11, while sylvite gave values of a = 1.870 and p = 2.56. These flaws prompted further study of the equation, resulting in the following empirical modification: [ ] It is obvious a real solution of the equation is possible for all values of ps and p. When PL > PS, V is negative, indicating that the particles will rise against the attraction of gravity. The validity of the modification is borne out by the fact that when values of a and p were back calculated for galena and sylvite using the modified equation, both minerals gave values of a = 1.038 and p = 3.01. With the modification shown in Eq. 2, Newton&apos;s friction factor becomes [ ]

Jan 1, 1976

By Alexander Field

IN THE light of the experimental data on equilibrium for the reaction C + FeO = Fe + CO in molten steel recently obtained by Kinzel and I Egan,1 it is necessary to revise current theories regarding the nature of equilibrium between carbon and FeO in the basic open-hearth furnace. According to the measurements of these investigators the equilibrium constant m for the above reaction for a pressure of dissolved CO equal to 1 atm. is equal to 0.0005 at 1550° C., when concentrations of carbon and. FeO are expressed in percentages by weight. Their work also shows that, with the pressure of CO fixed at 1 atm., not only is the product of carbon and FeO constant, but carbon and FeO are each independently constant-a circumstance which might have been predicted from theoretical considerations. At 1550° C., carbon is constant at about 0.025 per cent. and FeO at about 0.020 per cent., with the pressure of dissolved -CO equal to 1 atm., the product of these two constants being equal to the originally mentioned constant of 0.0005. Available data on the dissolved FeO content of samples taken from the metal bath at practical slag-metal equilibrium prove that this FeO content is determined solely by temperature and the effective FeO content of the slag. The distribution constant r at 1550° C., as determined by Herty, Gaines, Larsen, Simkins, Geruso and Watkins2 is equal to 0.0086. A slag would have to contain 0.020/0.0086 = 2.3 per cent. effective FeO or less in order to prevent the metal from containing more dissolved FeO than that required for equilibrium with CO at 1 atm. pressure. Such low percentages of FeO are never found in basic open-hearth slags at the completion of a heat when rate of carbon drop has become practi-

Jan 1, 1930