Search Documents

By Joseph S. Malesky

The discovery and development of explosives mark one of the most important findings in the history of civilization. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. For these reasons explosives are rightfully referred to as the forerunner of progress. An explosive may be defined as a substance (usually a mixture) that, when flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents. HISTORY OF BLASTING WITH EXPLOSIVES At one time workmen obtained stone blocks for building by grooving the rock with crude picks, driving wooden wedges into niches in the rock, and pouring water on the wedges; the swelling of the wood forced out the blocks. As late as the 17th century, fires were placed against the face of rock to crack it, and water was sometimes dashed on the heated rock to shatter it by sudden cooling. The progress of our country is synonymous with advancement of the improved manufacture and extended use of explosives. Coal had been

Jan 1, 1981

By R. H. McLean

Jet impingement produces two mechanisms to clean the bottom of a borehole during jet-bit drilling operations. One is an impact-pressure wave in the immediate area of jet impingement. The other is crossflow, which spreads across the bottom away from the pressure wave. Measurements of the vertical distribution of the cross-flow at several positions beneath a 4 3/4-in. tricone jet bit in a laboratory model show that the maximum velocity in the crossflow is directly proportional to the square root of the product of the rate of flow and the velocity of the jets through the nozzles (QV). Other measurements in the laboratory model show that gradients in the impact-pressure wave are directly proportional to the jet QV if the diameters of the nozzles are held constant. Consistency of the basic relationships through changes in the Reynolds numbers of the jets from 31,000 to 93,000 suggests that the laboratory results should be representative of typical flow in field operations having higher Reynolds numbers. Estimates of the impact-pressure waves under conditions other than those in the jet-bit model may be made by comparison with a less complex model—impingement of a jet against an unrestricted flat surface normal to the jet. Equations derived from current jet technology describe the wave in this simple system for a wide range of conditions. INTRODUCTION The efficiency of rotary drilling operations is strongly linked to the efficiency with which cuttings are removed. Cuttings remaining on the bottom of the borehole will impede further penetration by the bit until they are removed. Wasteful regrinding is prevented if the fluid circulated past the bit removes cuttings as rapidly as they are made. Most investigations of bottom-hole cleaning under bits have been concerned with the rate-of-penetration effects of bit type, nozzle configuration, fluid properties, pressure gradients and utilization of hydraulic horsepower. These investigations have shown that drilling muds, weighted to keep the pressure in the borehole greater than in adjacent formations and carrying material which forms a filter cake, apparently plaster cuttings against the bottom, making them difficult to remove. In addition to a demonstration of the factors causing poor cleaning, the most significant result of these previous investigations has been the increased use of jet bits accompanied by better hydraulic programs and better selection of drilling fluids. Undoubtedly, these practices have improved bottom-hole cleaning, but rates of penetration when drilling with muds are still often lower than would be expected with perfect cleaning." Although there is general agreement with the concept that increasing hydraulic energy at a jet bit often increases the rate of penetration by improving cleaning, research workers have differed as to the best criterion for evalyating hydraulics. Some lean toward maximizing the product of the rate of flow and the velocity through the nozzles (QV) others prefer to maximize the hydraulic horsepower at the bit;'"-' "till another says that neither criterion is universally suitable."' This controversy shows that conclusive field evidence has not established the superiority of either of these criteria. Analysis of the fluid flow which cleans the bottom should contribute to resolving the controversy. Impinging jets clean the bottom by creating two mechanisms capable of dislodging cuttings. One is the impact from the momentum of the jet and the other is the flaw parallel to the bottom away from the area of impingement. The impact force appears in the form of a pressure wave on the bottom and, in this paper, is called the impact-pressure wave. The flow parallel to the bottom is called crossflow. Fig. 1 illustrates these two mechanisms. This paper describes crossflow and the impact-pressure wave beneath jet bits and relates them to controllable parameters. Through these relations, criteria for use in designing hydraulics to achieve maximum use of the mechanisms of cleaning are derived. PROPERTIES OF CROSSFLOW CONCEPTS DEVELOPED IN PREVIOUS INVESTIGATIONS Concepts of scavenging the bottom by crossflow have been well discussed by Bobo, et al." They examine the means by which crossflow may create forces on cuttings and conclude that the cleaning action of crossflow can be increased by increasing the velocity of the flow stream close to the bottom. Using boundary layer theory, they indicate that a reduction in the viscosity of the drilling

Jan 1, 1965

By Charles Means

A THOROUGHLY modern coal-handling system has been installed at the Pittsburgh Terminal R. R. & Coal Co.'s new No. 8 shaft, or Coverdale mine, about 11 mi. (17.7 km.) from Pittsburgh on a spur f the Montour R. R. The Pittsburgh seam, which is the one worked, is reached at a depth of 342 ft. (104 m.). Power is delivered to the mine at 22,000 volts over a transmission line of the bow-arrow type of construction. A private telephone line connecting the various mines and the main office in Pittsburgh is carried on the same poles. The high-tension line is brought to an outdoor, step-down, transformer substation, where three 833-kv.-a., single-phase, 60-cycle, oil-insulated, self-cooled transformers reduce the potential to 2300 volts. The transformers are protected by electrolytic, aluminum-cell lightning arresters, horn gaps, and choke coils. High and low-tension busses, together with fuses, choke coils and air-break horn-gap switches with their remote-control operating mechanism are mounted on a substantial structural-steel tower 25 ft. (7.6 m.) in height. MINE SUBSTATION The transformer substation is adjacent to a pressed-brick building that houses direct-current substation equipment together with switchboards, etc., for the control and distribution of power. This building also contains the hoist for the men and supplies.

Jan 9, 1921

By M. C. LAKE

THE industrial development of the United States has been stimulated by the presence of high-grade iron ore in the Lake Superior district. These great deposits have been susceptible to economical extraction and are conveniently located for cheap lake vessel transportation to the great consuming centers. The district furnishes from 80 to 85 per cent of the iron ore annually consumed in the United States, and a full understanding of the available supply of this great commodity is so important that it is well to consider whether or not the industrial supremacy and national independence attained as a result of the abundance of cheap ore are permanent. The enormous deposits of high-grade ore available in the Lake Superior district have been the foundation upon which the vast industrial structure of the steel and allied industries has been built. It is extremely important to the country as a whole, and especially to those States and communities now dependent on Lake Superior ore for their prosperity, that their industries shall retain the particular advantages with which they are now endowed, and that a generous supply of high-grade raw material be available for their consumption at a satisfactory cost. The steel industry is so basic and fundamental that any fluctuation in the cost of its finished products as determined by the supply and cost of the raw materials involved in its manufacture will necessarily affect the business of a wide variety of industries which are dependent on it.

Jan 1, 1926

By Nelson Severinghaus

Mineral fillers have been defined as inert materials that are included in a composition for some useful purpose. Because this definition and the scope of this review are not specific-indeed, exceptions abound-accurate total statistics are unavailable. One source estimates the total production in the United States in 1979 at 11.3 Mt (12.5 million st) valued at $534 million, averaging $49.19 per ton. Included are a broad group of minerals-asbestos, barite, bentonite, ground limestone and dolomite, clays, diatomite, feldspar, micas, silica, talc. Additional references will be made to synthetic mineral-derived fillers such as aluminum hydrate, precipitated calcium carbonate, and pyrogenic and precipitated silicas and silicates. A section on related uses at the end of this chapter covers absorbents and filters. Mineral fillers can be included in compounds to accomplish a variety of final results. Hardness, brittleness, impact strength, compressive strength, softening point, fire resistance, surface texture, electrical conductivity, and a host of other physical characteristics may be modified by the inclusion of fillers. These effects are the result of properties of the fillers, including chemical activity, hardness, particle size, shape and distribution, surface structure, color, density, and refractive index. To facilitate an overview of the mineral filler industry, this chapter will review the general usage of fillers, the inherent characteristics that intensify their utilization, and similarly their manufactured characteristics. Major using industries will then be examined in detail. Specific information on deposits and processing for industrial minerals will be found in the appropriate commodity chapter. All of these same minerals have additional significant uses based on their chemical composition or other characteristics. References will be found in other use chapters and summarized in commodity chapters. The chart in Table 1, updated from the 4th edition of Industrial Minerals and Rocks, illustrates the major mineral fillers (both natural and manufactured) and their more important end uses. Use of Mineral Fillers Archaeologists have found that more than 5000 years ago, bitumen used for mortar and waterproofing contained mineral contaminants that acted as fillers. Since that time man has added mineral products to compounds to improve certain characteristics. Perhaps the most common objective of filler usage is reduction of cost of the end product. Certainly the inclusion of a filler that costs 2¢ per 0.45 kg (lb) will reduce the cost of a plastic product whose resin costs 50¢ per 0.45 kg (lb). But the decision to use a specific filler is not that simple. It may "soak up" binder, making a compound more viscous and perhaps preventing its flow into a mold as an injection molding compound, but similarly will give good anti-sag characteristics to putty, caulking compound, or undercoating. Fillers may be incorporated to modify: 1) Cost 2) Physical characteristics 3) Flow characteristics 4) Fire resistance 5) Density 6) Heat conductivity 7) Color or brightness and opacity 8) Hardness, brittleness, impact strength 9) Deformity, viscosity, softening point 10) Processing problems 11) Electrical conductivity 12) Surface texture 13) Thermal expansion characteristics 14) Abrasion resistance

Jan 1, 1983

By Howard L. Hartman, Eugene P. Pfleider

The paper relates to the laboratory and pilot plant studies that have been carried out by Sherritt Gordon Mines Ltd., Metallurgical Research Div., in developing the ammonia pressure leach process for extracting Cu, Ni, Co, and S from high grade Ni concentrate produced from Lynn Lake ores and describes in some detail the chemistry of the process. In the leaching stage air, ammonia, and sulphide minerals react in a sequence of inter-related steps to produce soluble amines of Ni, Cu, and Co in a solution containing sulphate, thiosulphate, polythionate, and sulphamate ions and a controlled amount of free ammonia, the iron and other components of the concentrate remaining as an insoluble residue which is separated from the leach solution by filtration. The pregnant solution produced in leaching is further treated by boiling to precipitate and remove Cu as cuprous sulphide, leaving a copper-free solution with a composition suitable fir subsequent precipitation of Ni and Cu by H,. The progress of individual reactions in leaching and copper removal is discussed. The effect of variables such as temperature, pressure, ammonia concentration, particle size, and agitation is outlined and the technique of thionate control in leach solutions is described. Data is given for the physical and chemical reactions involved in precipitating copper from leach solutions as Cu sulphide by boiling.

Jan 1, 1956

By P. E. Schauer

During the initial nine-year deple-tion of the McKamie-Patton pool gas-condensate reservoir, the pressure behavior and fluid analyses indicated pressure maintenance by gas injection would be attractive relative to continued pressure depletion. As a result, a gas cycling program was inaugurated in Aug., 1949, which has since maintained reservoir pressure. In order to evaluate the benefits of this program, the recoveries for natural depletion and for cycling followed by blowdown were determined by calculating the fractional balance of the molar quantities of vapor and liquid remaining in the reservoir and produced at the surface for various stages of depletion. The results of the investigation show theoretical ultimate recovery due to the cycling program will be 42 per cent greater than would be realized under pressure depletion type operation. INTRODUCTION The benefits of gas injection pressure maintenance programs in condensate reservoirs have been recognized and qualitatively described in several papers1-8 during the past 15 years. Some of these papers also describe methods for calculating the increased recovery realized from cycling; however, as a rule, hypothetical reservoirs were used as examples".'.. This paper presents an evaluation of the pressure maintenance program for the McKamie-Patton condensate reservoir and includes a description of the fractional balance method employed to determine the benefits. Reservoir Development and Characteristics The McKamie-Patton pool, Lafayette County, Ark., was opened in June, 1940, with production obtained from the oolitic Smackover lime at a depth of approximately 9,300 ft. The structure is an anticline 8 miles long by 1 to 2 miles wide, and is one of many productive Smackover structures in Southern Arkansas. Of predominant importance is the condensate-bearing gas cap portion of the reservoir, which covers approximately 4,000 acres, attains a maximum thickness of some 200 ft, and has an average thickness of 90 ft. Development of the cap was accomplished with 21 wells drilled on 160 acre spacing. An isopach map of the cap is shown in Fig. 1. In addition, an oil rim is present along most of the periphery of the pool. Production practice includes field separation of black oil, and a high pressure gathering system which carries total well stream from gas cap wells to a plant where condensate is separated and the gas is processed for recovery of natural gasoline, butane, and propane. Since the gas contains appreciable hydrogen sulfide, it is removed by amine contact, after which free sulfur is produced by the Claus process. Core analyses from 1,767 gas cap formation samples averaged 14.2 per cent porosity and 379 md dry air permeability. Connate water was restored on seven samples of gas cap rock by air-brine capillary techniques, from which the interpreted water saturation averaged 28.17 per cent. During the early life of the field, it was believed the recovery mechanism, based on several of the other regional Smackover reservoirs, might be a natural water drive. However, subsequent production and pressure history revealed that the gas cap would not be produced by water drive, but would behave as a closed reservoir. In this respect, during the nine-year period of natural depletion from initial production to Aug., 1949, the cap production of 84.3 billion

Jan 1, 1958

By K. F. G. Hosking

I read Professor Gaudin's paper with great interest and pleasure because for some time I have held that the chemical aspect of comminution is a subject of considerable importance to the mineral dresser and deserves to be thoroughly investigated. It does seem appropriate, however, to emphasize the fact that "fresh" edges and corners produced by the grinding of solids display enhanced reactivity has been recognized and utilized in the development of certain mineral identification techniques. Some of these techniques are worth noting, not only because they might facilitate research in the aspect of mineral dressing under discussion, but also because they emphasize the fact that many mineral species commonly regarded as being very inert can display a surprising reactivity when in the freshly ground state. In 1951 Isakov published a number of tests for the components of certain mineral species which depend essentially on grinding in a mortar a mixture of the material under investigation with a solid reagent. Thus when stibnite, 4(Sb2S,), is ground with sodium or potassium hydroxide, the antimony is revealed by a momentary development of a yellow color which changes in air to orange-red. Other antimony minerals need a preliminary treatment before the test can be carried out. This consists of grinding with aluminium sulfate, ferric sulfate or potassium bisulfate, and breathing upon the resultant mixture.

Aug 1, 1956

By J. R. Linney

THE Eastern magnetite industry has not failed in its contribution to the war program during the past year. Man-power shortage was the critical problem in maintaining production and for the last half of the year, owing to lack of man power, it was necessary for some mines to change from seven to six days per week schedule. At Cornwall, Pa., the mine operated by the Bethlehem Steel Co. produced approximately 2,000,000 tons of crude ore and 1,200,000 tons of iron ore concentrates, a decrease of about 10 per-cent compared with the previous year. Railroad haulage in the open-pit at this mine was discontinued, being replaced by Mack trucks of approximately 30 tons' capacity. At the Mt. Hope mine in New Jersey, the Warren Foundry and Pipe Corp. produced about 195,000 long tons of crude ore obtaining 70.000 long tons of lump ore and 35,800 long tons of concentrates. An additional 24,500 long tons of concentrates was produced from a stock pile of 47.000 long tons of crude ore accumulated during the latter half of 1943, following the fire in their old dry mill. All of this material was handled through their Brown

Jan 1, 1945

By T. K. Prentice

ABSTRACTED AND REVIEWED BY E. W. DAVIS,* MEMBER A.I.M.E. THE January-February number of the Journal of the Chemical Metallurgical and Mining Society of South Africa is made up entirely of a discussion of Ball Wear in Cylindrical Mills. Following the principal paper by T. K. Prentice are several remarkably pertinent and carefully prepared discussions. Few persons in this country would be likely to see this publication, and since the information presented is new and of current interest, it seems desirable to abstract and review this publication for the benefit of the members of the A.I.M.E. The purpose of the investigation is stated in the first two paragraphs of Prentice's paper, as follows: Early in 1941, The Chamber of Mines Steel Products, Limited, initiated a series of tests under semi-working scale conditions to determine, if possible, those physical and chemical properties of a ball which make it resistant to wear when used in a cylindrical mill as a grinding medium, with the primary object of incorporating those beneficial qualities in the balls being produced at their works. This paper describes the tests carried out and discusses the results obtained. From these results it was possible to formulate a new theory relating to ball wear in cylindrical mills. This theory is presented in the second portion of this paper. PRACTICAL BALL-MILL TESTS IN A CYLINDRICAL MILL Part I of the paper begins with a discussion of the methods used for the manufacture of grinding balls in South Africa. The following paragraph is of particular interest. The cast steel ingots, 4 ¼ - in. square by 3 ft. 6 in. long, are re-heated in a gas-fired sloping stationary-hearth furnace and then rolled in a six-pass continuous mill into 2 5/8 in. round billets. Some of these billets are then removed and cut into suitable lengths for forging into 4 in., 3 ½ in., 3 in. or 2 ½ in. balls by means of three Drop and two Beché hammers, but the greater number, whilst still at about 1,000 ºC., pass directly into a set of scroll rolls which produce, in an ingenious manner, finished 3 in. balls direct from the 2 5/8 in. billets. Except in special cases, all balls are allowed to cool in the atmosphere and are not water quenched. Details of the Tests In order to enable the reader to evaluate properly the results and conclusions in the rest of the paper and in the discussions following the paper, most of the information presented by the author under this heading is quoted: ….. The testing unit was a nominal 30 in. diameter and 18 in. long centre discharge Denver Ball Mill. The ore pulp to the ball mill comprised a small portion of the normal feed to one of the fourteen City Deep 5 ft. 6 in. X 22 ft. tube mills, and the grinding media consisted of the balls under test plus other balls to give the desired load. The running time of the test-mill was divided into approximately equal periods of five days 13 ½ hours each. The usual procedure was to examine and make up the load

Jan 1, 1944

By B. D. Cullity, O. P. Puri

The magnetostrictia of nickel after increasing amounts of plastic elongation was measured at field strengths up to 1500 oe. In addition, the residual stress was measured by means of X-ray line shifts. The observed decrease in magnetostriction following plastic strain is shown to be associated with residual compressive stress. If a metal bar, whose longitudinal axis is taken as the x direction, is plastically elongated in the x direction and then unloaded, X-ray diffraction measurements will indicate the presence of a residual compressive macrostress 0%. However, stress measurement by means of mechanical relaxation does not reveal any macrostress. In a previous paper1 the fictitious macrostress indicated by X-rays was ascribed to a particular distribution of micro-stress, namely, one in which the bulk of the material was stressed more or less uniformly in compression and a very small portion in tension. It was shown that this distribution would account for Neurath's measurements2 of magnetic losses in silicon steel, because of the effect of residual stress on magnetostriction. The present paper is concerned directly with magnetostriction, in nickel, and with the effect on magnetostriction of the residual stress created by plastic elongation. The residual stress was determined by measurements of X-ray line shifts. MATERIAL AND METHODS Commercially pure "A" nickel was investigated. Its nominal composition, in weight percent, is 99.4 Ni + Co, 0.2 Mn, 0.15 Fe, 0.1 Cu, 0.1 C, 0.05 Si, and 0.005 S. Magnetostriction was measured by means of SR-4 electrical-resistance strain gages mounted on specimens 1/4 in. sq and 8 in. long. Magnetic fields up to about 1500 ce were provided by a multilayer, non-cooled solenoid. A considerable amount of heat was developed at the higher field strengths, and, to avoid errors due to changes in the specimen temperature, the following procedure was adopted. Each measurement of the magnetostriction X at a particular field strength H was preceded by demagnetization and an adjustment of the strain indicator to zero; the field H was then quickly switched on and the strain read immediately. Curves of ? vs H were flat for field strengths above about 750 oe for all specimens, and this constant value of X was accordingly taken as the saturation magnetostriction ?s The X-ray measurements of residual stress were made with a Norelco diffractometer on specimens cut from flat bars 1 1/4 in. wide, 1/8 in. thick, and 12 in. long. These measurements were confined to lattice planes parallel to the surface of the specimen. Two reflections were studied: the 311 CrKß line at 28 = 157 deg, and the 420 CuKal line at 28 = 155 deg. The line centers were determined by fitting a parabola to the peak of the line, as suggested by Ogilvie3 and as modified by Koistinen and Marburger.4 The CuKa doublet from the plastically elongated specimens was first resolved by the Rachinger method5. All X-ray measurements were made by counting at fixed angular positions. RESULTS The results of the magnetostriction measurements are shown in Fig. 1 and Table 1. The magnitude of

Jan 1, 1963

By W. C. Ellis, E. S. Greiner

METALLIC titanium has been prepared in small quantities since the beginning of the century. Hunter1 reported in 1910 that he obtained a malleable product of 99.9 pct purity by the reduction of the tetrachloride by sodium in a closed container. Later Van Arkel2 and Fast3 prepared small quantities of malleable titanium by thermal decomposition of titanium iodide. Another method for producing malleable titanium from tetrachloride was reported by Kroll4 who used magnesium as the reducing agent. More recently Dean, Long, Wartman, and Anderson5 working at the U.S. Bureau of Mines have reported the preparation of the metal on a pilot plant scale by the reduction of titanium tetrachloride by magnesium in an atmosphere of helium. Their product, which is malleable, was used in the present investigation. Early in 1948 after the work of this paper: was completed Campbell, Jaffee, Blocher, Gurland, and Gonser6 described the strength and working characteristics of pure titanium which was prepared by the iodide method on a scale producing 300 to 600 g per run, in the form of 0.3- to 0.4-in. diam rods. Their product is characterized by low hardness and large capacity for cold work which they attribute to a high degree of purity with respect to oxygen, nitrogen, and carbon. Titanium has a melting point of about 1725°C5 it may be classed as a light metal since the specific gravity is 4.5 g per cc-1. The crystal structure is close-packed hexagonal from room temperature t0 885°C. Above this temperature the structure is reported7 as body-centered cubic. The change in crystal structure has been associated with discontinuities in specific heat8 electric resistance9 and thermoelectric force10 at temperatures near 890°C. It is reported11 that annealed titanium has a tensile strength 0f 78,700 psi which can be increased by cold-work to 123,000 psi. In the present investigation, the lattice constants at room temperature, the thermal expansivity between 30 and 800°C, as well as the electrical resistivity and thermoelectric force against platinum between - 200 and 1000°C have been determined. MATERIALS For the measurements, two series of specimens were prepared from titanium furnished by the U. S. Bureau of Mines. The first was lade from an annealed sintered compact, 0.38 in. thick. Sections of the compact were cold-swaged with intermediate anneals in vacuum to the sizes used. Sizes over 0.25-in. diam were annealed at 1000°C and smaller sizes at 800°C. Specimens originating from the sintered compact are designated in this paper as A. The second series of specimens was lade from a rod of titanium, 0.19 in. in dial, which was cold-swaged with the necessary intermediate anneals to the required sizes. This series of specimens is designated B. The impurities in the specimens of titanium, determined by chemical analysis, are given in Table I. Oxygen and nitrogen which were not determined by analysis, are probably present although in small quantities in view of the ductility of the material.

Jan 1, 1948

By S. L. Hoyt

Some of the more important properties of finished materials are strength, ductility, toughness, resistance to alternating and repeated stresses, etc. Of these, the property that appears to have received the least consideration, at least in this country, is toughness, which is due, possibly, to our regarding toughness as a qualitative property or, at any rate, as one that parallels ductility. This arises out of our greater experience with the simple carbon steels in the rolled or forged (non-heat-treated) condition which, qualitatively, are tough if ductile and are not tough if brittle. In this way we have erroneously become accustomed to judging the toughness of a material from its behavior in the tensile or similar test. The point of view presented in the present paper is that toughness, like hardness or tensile strength, should be regarded as an independent property and of sufficient importance to require, in so far as that may be possible, quantitative determinations. If such be true, it becomes at once necessary to devise experimental means for measuring or valuating toughness, and the notched-bar impact test (the Charpy test) is advanced as the most logical test that has so far been developed for this purpose. It is further advanced, with particular emphasis, that we have two kinds of toughness to deal with and, accordingly, they will be dealt with independently. Classification of Materials According to Toughness Toughness has been defined somewhat as follows: Tough materials are those that offer considerable resistance to permanent deformation but which, once such resistance has been overcome, may be deformed plastically, but only by the expenditure of considerable energy. In other words, tough materials may be deformed plastically but they absorb a considerable amount of work in the process. This kind of toughness may be called "static" toughness when the rate of loading is reasonably slow or "dynamic" toughness when the rate of loading is comparatively rapid, as in impact testing, but in all cases the stress distribution is essentially uniform. However, static toughness does not

Jan 1, 1920

By J. J. Frawley, W. J. Childs

Experiments were carried out to induce grain refinement during solidification by applying vibrational energy (freq 20 kc) to small specimens of bismuth, tin, and bismuth-tin alloys. The results show that if the intensity of the applied sound -field is not great enough to fragment the growing dendrites of a pure metal, no grain refinement is observed and the pain size of the dynamically nucleated specimens is the same as the grain size of a specimen statically supercooled the same amount. Bismuth specimens did not show any grain refinement; whereas, the tin specimens did show grain refinement. This phenomenon is the result of the difference in growth habit between the bismuth and tin dendrites. The bismuth-tin alloys showed grain refinement and, in addition, the segregation pattern was changed. THE solidification process is a change in phase requiring the nucleation of the solid phase from the liquid and the growth of this solid phase at the expense of the liquid phase. Since many physical properties and also the integrity of a casting are dependent on the solidification process, understanding and controlling this process are very important.' A good example in the controlling of a cast structure using heterogeneous nucleation theory is the reduction of grain size in aluminum castings by nucleation catalysis.2 This mechanism of nucleation catalysis has been explained by Turnbull.3 Another technique for grain refinement, which has received much attention but the mechanism has not been fully understood, is to vibrate the solidifying melt. Vibrations can be applied to the melt either by vibrating the mold directly or by introducing a vibrating rod into the melt.4-13 Three mechanisms have been proposed to explain this phenomenon: 1) The mechanical fragmentation of the original dendrites that grew into the melt. These crystals or fragmented dendrites act as new growth sites. 2) The nucleation of new grains in the liquid by the generation of very high pressure pulses caused by cavitation in the liquid. 3) The remelting of the dendrite arms during the solidification process. This mechanism is operative only in alloy systems and would be enhanced by stirring or mechanical vibration. The purpose of this investigation was to determine the mechanism that will increase the number of grains when mechanical energy is introduced into a solidifying melt. APPARATUS The unit used to generate the ultrasonic vibrations was manufactured by the Redford Co., and is similar to the one used in ultrasonic soldering. Fig. 1 is a sketch of the major components used for generating ultrasonic vibrations. The crystal transducer assembly consisted of four lead zirconate ti-tanate piezoelectric crystals in an aluminum holder. An acoustical horn, which was fabricated from stainless steel, was attached to the holder by a set screw. The resonant frequency of this unit was 20,000 cycles per sec. A Pyrex crucible, 4 in. in diam and 4 in. high, was contained in a hole in the top of the horn. The piezoelectric crystals changed volume when excited by an electric signal, thereby generating a sound signal which passed through the horn. The crucible was coupled to the horn by a liquid silicone oil. The purpose of the couplant was to transmit the soundwaves from the horn to the crucible. Without the couplant, much of the sound energy would be lost. The energy transmitted was sufficient at the resonant frequency used, so that acoustical cavitation always occurred in the molten metal. The presence of acoustical cavitation was detected by the characteristic hissing sound emitted from the liquid. EXPERIMENTAL PROCEDURE The influence of ultrasonic vibration on the grain refinement of bismuth, tin, and bismuth-tin alloys was studied. These metals were chosen because of their low melting temperature and the relative ease with which they can be thermally supercooled. The following procedure was used for obtaining large amounts of supercooling. Pure bismuth (99.999+), which was received in bar form, was mechanically broken into pieces small enough to be accommodated in a 50 ml beaker. About 200 to 300 g of bismuth and a few grams of SnCl2 as a flux were placed in the 50 ml beaker and melted by induction heating. The melt was held for 20 min at

Jan 1, 1970

By AIME AIME

RECENT experiments in reflected sunlight photography in mine shaft's' and. slopes in the McAlester, Oklahoma, coal-mining district have been so satisfactory as to indicate that such a method has definite scientific value. The entrances to abandoned deep shafts and slopes on Choctaw and Chickasaw Indian coal lands in Oklahoma are being filled or bulk-headed by the U. S. Geological Survey under Public Works Project F. P. 63-C&C. Inasmuch as these mines may be reopened at some future time when there is a demand for coal, H. I. Smith, Chief of the Mining Division, suggested that photographs of deep shafts would be of value. Such photographs would show timber details and the general condition of the walls. Photographic records of the exact status of shafts when filled will facilitate operations in reopening.

Jan 1, 1936

By T. K. Prentice

The January-February number of the Journal of the Chemical Metallurgical and Mining Society of South Africa, 1943, is made up entirely of a discussion of Ball Wear in Cylindrical Mills. Following the principal paper by T. K. Prentice are several remarkably pertinent and carefully prepared discussions. Few persons in this country would be likely to see this publication, and since the information presented is new and of current interest, it seems desirable to abstract and review this publication for the benefit of the members of the A.I.M.E. The purpose of the investigation is stated in the first two paragraphs of Prentice's paper, as follows: Early in 1941, The Chamber of Mines Steel Products, Limited, initiated a series of tests under semi-working scale conditions to determine, if possible, those physical and chemical properties of a ball which make it resistant to wear when used in a cylindrical mill as a grinding medium, with the primary object of incorporating those beneficial qualities in the balls being produced at their works. This paper describes the tests carried out and discusses the results obtained. From these results it was possible to formulate a new theory relating to ball wear in cylindrical mills. This theory is presented in the second portion of this paper. Practical Ball-mill Tests in a Cylindrical Mill Part I of the paper begins with a discussion of the methods used for the manu- facture of grinding balls in South Africa. The following paragraph is of particular interest. The cast steel ingots, 4¼ in. square by 3 ft. 6 in. long, are re-heated in a gas-fired sloping stationary-hearth furnace and then rolled in a six-pass continuous mill into 25/8 in. round billets. Some of these billets are then removed and cut into suitable lengths for forging into 4 in., 3¼ in. , 3 in. or 2½ in. balls by means of three Drop and two Beche hammers, but the greater number, whilst still at about 1,000, pass directly into a set of scroll rolls which produce, in an ingenious manner, finished 3 in. balls direct from the 25/8 in. billets. Except in special cases, all balls are allowed to cool in the atmosphere and are not water quenched. Details of the Tests In order to enable the reader to evaluate properly the results and conclusions in the rest of the paper and in the discussions following the paper, most of the information presented by the author under this heading is quoted: The testing unit was a nominal 30 in. diameter and 18 in. long centre discharge Denver Ball Mill. The ore pulp to the ball mill comprised a small portion of the normal feed to one of the fourteen City Deep 5 ft. 6 in. X 22 ft. tube mills, and the grinding media consisted of the balls under test plus other balls to give the desired load. The running time of the test-mill was divided into approximately equal periods of five days 13½ hours each. The usual procedure was to examine and make up the load

Jan 1, 1947

By T. K. Prentice

The January-February number of the Journal of the Chemical Metallurgical and Mining Society of South Africa, 1943, is made up entirely of a discussion of Ball Wear in Cylindrical Mills. Following the principal paper by T. K. Prentice are several remarkably pertinent and carefully prepared discussions. Few persons in this country would be likely to see this publication, and since the information presented is new and of current interest, it seems desirable to abstract and review this publication for the benefit of the members of the A.I.M.E. The purpose of the investigation is stated in the first two paragraphs of Prentice's paper, as follows: Early in 1941, The Chamber of Mines Steel Products, Limited, initiated a series of tests under semi-working scale conditions to determine, if possible, those physical and chemical properties of a ball which make it resistant to wear when used in a cylindrical mill as a grinding medium, with the primary object of incorporating those beneficial qualities in the balls being produced at their works. This paper describes the tests carried out and discusses the results obtained. From these results it was possible to formulate a new theory relating to ball wear in cylindrical mills. This theory is presented in the second portion of this paper. Practical Ball-mill Tests in a Cylindrical Mill Part I of the paper begins with a discussion of the methods used for the manu- facture of grinding balls in South Africa. The following paragraph is of particular interest. The cast steel ingots, 4¼ in. square by 3 ft. 6 in. long, are re-heated in a gas-fired sloping stationary-hearth furnace and then rolled in a six-pass continuous mill into 25/8 in. round billets. Some of these billets are then removed and cut into suitable lengths for forging into 4 in., 3¼ in. , 3 in. or 2½ in. balls by means of three Drop and two Beche hammers, but the greater number, whilst still at about 1,000, pass directly into a set of scroll rolls which produce, in an ingenious manner, finished 3 in. balls direct from the 25/8 in. billets. Except in special cases, all balls are allowed to cool in the atmosphere and are not water quenched. Details of the Tests In order to enable the reader to evaluate properly the results and conclusions in the rest of the paper and in the discussions following the paper, most of the information presented by the author under this heading is quoted: The testing unit was a nominal 30 in. diameter and 18 in. long centre discharge Denver Ball Mill. The ore pulp to the ball mill comprised a small portion of the normal feed to one of the fourteen City Deep 5 ft. 6 in. X 22 ft. tube mills, and the grinding media consisted of the balls under test plus other balls to give the desired load. The running time of the test-mill was divided into approximately equal periods of five days 13½ hours each. The usual procedure was to examine and make up the load

Jan 1, 1947

By N. Mungan

Laboratory water floods were performed in oil-wet and waterwet alundum and Torpedo cores, displacing a refined oil with n-hexylamine or Triton X-100 solution. Also, some floods were performed in which a sucrose solution was displaced with n-butyl alcohol. The Purpose ot the tests was to see if the oil recotlery could be increased and to examine what role the inter-facial tension reduction and wettability change play in the recovery mechanism. it was found that the chromatographic transport of amine was influenced by core wettability. In oil-wet cores, the rate of advance of the amine band could be predicted from equilibrium chromato-graphy, while in water-wet cores the amine band moved faster than predicted, indicating a non-equilibrium process. By reducing the interfacial tension to 1.1 dyne/ cm, oil recovery was increased. More oil was recovered from Dri-filmed cores than from water-wet cores. Reversing the wettability of the porous media from oil-wet condition also resulted in some additional oil recovery. Neutral wettability floods did not increase oil recovery. INTRODUCTION Interfacial forces in petroleum reservoirs are responsible for retention of large quantities of residual oil. Increasing exploration costs have created an incentive to attempt recovery of this residual oil by new and novel processes. One novel process involves changing the interfacial forces by introducing a chemical into the reservoir during water flooding. Recently, several investigators have carried out laboratory displacement tests using amines. lt3.4 The amines adsorbed onto initially water-wet core surfaces, changing them to oil wet. Additional oil was recovered when the cores were flooded in a manner reversing the. wettability from oil-wet conditions. In all these studies, the wettability reversal was considered responsible for increased oil recoveries although it was noted that amines also reduced oil-water interfacial tension. In the present study, displacement experiments were performed in water-wet and Dri-filmed cores. The purpose was to separate the effects of lowering the interfacial tension from changing the wettability. LABORATORY STUDY All experimental data given in this paper have been obtained at a temperature of 70F + 1 and prevailing atmospheric pressure. FLUIDS AND MATERIALS The oil used in these experiments* was washed with H2S04 and passed through two 100-200 mesh silica-gel beds to remove unsaturates and surface active impurities. Normal hexylamine** of practical purity was used, and the alundum cores*** were composed of nearly pure A1203. Fused quartz (SiOi) and Lucalox (A12 )t plates were used in the contact angle measurements. DISPLACEMENT TESTS Displacement tests were performed in alundum and Torpedo cores. Before displacement runs, cores were acidized with 0.1 normal HCI, flushed with distilled water and fired at 1,200F to make them water wet. This procedure also reduced water sensitivity of the Torpedo cores. Oil-wet cores were prepared from water-wet cores by flowing several pore volumes of 1 per cent by weight Dri-film SC-87 solution in heptane through the cores, flushing the cores with nitrogen, evacuating, and finally heating the cores at 300F for 4 or 5 hours. Between floods, cores were cleaned by conventional procedures and treated again as above.

Jan 1, 1965

THE Institute met on Wednesday evening, May 22d, in the parlor of the Stanton House, Dr. T. Sterry Hunt, President, in the chair. The President delivered an introductory address on the Brown Hematite Deposits of the Great Valley, after which the following papers were read and discussed : Note on the Result of an Experiment with the Wheeler Process of Combining Iron and Steel in the Head of a Rail, by W. E. C. Coxe, of Reading, Pa. On the Jenks Corundum Mine, Macon County, N. C., by Dr. R. W. Raymond, of New York City. On Wednesday afternoon, previous to the opening session, the members who had already arrived in Chattanooga, were taken by the Local Committee to the works of the Roane Iron Company, and Chattanooga Iron Company, and then to the top of Lookout Mountain, where, at the request of the members present, Dr. Hunt described the geological and geographical features of the Chattanooga region, with the magnificent panorama spread out before them as a map. On Thursday morning an excursion was made by steamboat down the Tennessee River as far as Shellmound. Here cars were taken to the coal mines of the Dade Coal Company, where the members were courteously received by Mr. E. B. Wells, the Superintendent. After a trip through the mines the party partook of a collation provided by the company. South Pittsburgh, on the Tennessee River, was next visited, where the Southern States Coal, Iron and Land Company have a large blast-furnace plant in the course of erection. After conducting the party through the works, shops, etc., Mr. James Bowron, the manager, entertained the members with graceful hospitality at dinner. The second session was held on Thursday evening for the transaction of business. The President, Dr. T. Sterry Hunt, appointed Messrs. W. E. C. Coxe, R. H. Richards, and F. J. Slade, scrutineers, to examine the ballots for officers for the ensuing year.

Jan 1, 1879

By A. T. Churchman

The deformation modes of rhenium have been identified as those typical of the hexagonal metals, titanium, zirconium, and beryllium whose c/a ratios, in common with rhenium, are less than ideal for close packing. Slip is observed on (1010), (1011), and (0001) planes and twinning on (1121), (1122), and (1012) planes. The very high rate of work hardening is believed to be associated with intersecting partial dislocations on two (1010) systems which can combine to form sessile barriers. If the stacking fault energy is low, as postulated by Seeger, these barriers should be strong and not easily bypassed by cross slipping. Such an explanation could also account for the very small temperature dependence of the yield stress which was observed. RHENIUM is interesting scientifically as a member of the group of high melting point hexagonal metals: titanium, beryllium, and zirconium with a c/a ratio less than that for ideal close packing. Unlike them, however, it work hardens at a very high rate. This rate is greater and continues to a much higher degree of deformation than for nickel, normally considered to have a high rate of work hardening. This paper presents experimental observations on the modes of deformation of rhenium and, by comparison with other hexagonal metals, some speculation on the cause of the high work hardening. MATERIALS Johnson, Matthey rhenium powder of both 99.9 pct and 99.5 pct purity, see Table I, was compacted at 10 tons per sq in., part sintered at 1350°C in vacuo, and finally arc melted in a "gettered" argon atmosphere arc furnace to produce small buttons. Little difference was observed in the as-cast hardness or working down behavior of the two purities suggesting that either silicon and potassium do not have a significant effect on the working properties of rhenium or they were lost during arc melting. SPECIMEN PREPARATION The cast structure was broken up by cold-rolling with inter-stage annealing at 1600o or 1800°C in a vacuum high-frequency furnace using a tungsten susceptor. Strip for tensile testing was taken from two thicknesses of material 0.011 and 0.064 in. The former with intermediate anneals at 1800°C had a grain size of 900 grains per sq mm, while the latter with inter-stage annealing at 1600°C had a grain size of 3600 grains per sq mm. A coarse grain size was obtained by secondary recrystallization in a half button cold-worked by 30 pct reduction. Annealing times of from half an hour to several hours at 2200° to 2600°C in a "gettered" argon atmosphere arc furnace1 resulted in grains of up to 2 mm diam.

Jan 1, 1961