Search Documents

By R. G. Mallon, R. L. Braun

Primary copper-sulfide ore deposits that are well below the water table can be chemically mined by in-situ high-pressure leaching. The leaching is accomplished by pumping oxygen gas into the bottom of a large underground flooded column of rubblized ore. Part of the injected oxygen dissolves under the high hydrostatic pressure in the column. With a high enough injection rate, the excess oxygen gas induces a convective circulation of oxygenated solution within the rubble column, which transports dissolved oxygen throughout the system. At elevated temperatures, this results in a relatively rapid dissolution of the copper minerals. A method of calculating the leaching rates is presented. The calculation is done by means of a finite-difference computer code that couples all of the processes relating to copper leaching, convective circulation, and the injection, dissolution, and consumption of oxygen. Results of the calculation for a typical case show that over 70% of the copper can be extracted in less than six years with good efficiency in oxygen utilization.

Jan 1, 1976

By L. H. Robinson

A proposed method of drilling utilizes sequential detonation of two types of explosive charges delivered to the hole by a conventional drilling fluid through pipe. A shaped charge first produces a long thin hole. A second charge, called a gauging charge, is pumped into the thin hole, explodes, and enlarges it to full gauge. In one suggested configuration, the explosives are contained in cylindrical capsules 4- to 5-ft long. A drilling head is positioned 2- to 3-ft off bottom. When a capsule is pumped to the bottom of the hole and stops, pressure inside the drill pipe increases and differential pressure detonates the explosive. Primacord along the length of the capsule disintegrates the capsule. The debris circulates out of the hole with the drilling fluid. The gauging-charge action was examined using 2-ft cubes of Berea sandstone. The sandstone (18 per cent porosity) was vacuum-saturated with water and surrounded by concrete. To prevent reflected tensile pulses, the acoustical impedance of the concrete matched that of the sandstone. A 750-psig pressure was applied to a drilling fluid within a shaped-charge-formed hole before detonating the gauging charge. In these tests, 190 gm of rock were removed for each gram of explosive detonated. A similar series of experiments on low-porosity (0.40 per cent) metamorphic limestone provided a more rigorous test. Extensive fracturing from the gauging-charge action prevented an estimate of the volume of the expanded hole. The diameter of the hole was irregular, ranging from about 2 to 4 in, or about fivefold larger than the hole created by the shaped charge. INTRODUCTION In the past, explosives have found a varied but somewhat limited use in the oil field. An early well stimulation technique, still in use today, in vo lves shooting ni troglycerin to en large the borehole and to increase matrix permeability near the wellbore. Bullets and jets are now the conventional method of perforating casing and tubing. Detonations are frequently used to "back off" or "shoot off" stuck pipe and, of course, seismo-graphic work has long depended on explosive-generated pulses to find attractive earth structures. Efforts to use explosives in drilling operations have received limited examinations1-3 which, in one respect, is surprising because explosives offer one way to transmit large amounts of energy directly to the bottom of the hole. Recently, Ostrovskii l described a Russian method of drilling with explosives that utilizes small capsules containing explosives which are pumped into the mud stream to the bottom of a borehole. As the capsules leave the end of the drill pipe, a detonation mechanism is armed. Impact detonates the explosive. In another configuration, two liquids (an oxidizing agent and fuel) in the capsule are separated by a frangible membrane. Separately, the liquids are nonexplosive. Near the bottom of the drill pipe, the capsule passes through a narrow constriction which ruptures the membrane. The mixing of the liquids produces an explosive. Impact is again used to detonate the explosive. About the time Ostrovskii was developing his method, Humble Oil & Refining Co. was independently doing research on another explosive drilling concept based on the sequential detonation of two types -of explosive charges. The proposed technique consisted of alternately pumping a shaped charge and then a "gauging charge" down a well. The shaped charge should drill a long, tapered hole, and the gauging charge should expand it to full gauge. This paper presents the visualized drilling concept and gives results of laboratory work which showed that sequential firing of charges can form hole at an attractive charge-to-rock removal ratio. An important finding was that increased environmental pressure, which is to be expected in wells, increases rock removal efficiency of the gauging charge.

Jan 1, 1966

By J. Ostachowicz, B. Holynska, M. Lankosz

The paper presents an analyzer and the method for the continuous determination of weight percentage of ore grains with diameter smaller than 75 pm in mineral slurries. The method is based upon the measurement of characteristic x-rays of copper excited by primary radiation of two different energies 16.5 keV and 60 keV from Pu238 and Am241 sources respectively. Additionally the backscattered primary radiation is measured in order to correct the variations of the solids content in the slurry.

Jan 11, 1979

By R. D. Carnahan, J. E. White

ThE use of strain gages in the measurement of microplastic behavior of materials is well-known.'-3 Recently it has been suggested that similar techniques might be useful for determining stress relaation. It is the purpose of this report to comment on the use of strain gages in the measurement of strains in the vicinity of 10"6. We will also discuss observations of an anomalous anelastic behavior apparently associated with small temperature changes, which accompanies the unload portion of a load-unload microstrain test. The key to successful strain determinations at levels below 1 pin. per in. is a good gage-mounting technique and either precise ambient temperature control or a set of matched temperature-compensated gages. The importance of good mounting cannot be overemphasized, for example, as in the use of Eastman 910 contact cement. If the cement layer is not sufficiently thin and properly hardened, it is possible to observe anomalous negative stresses when small loads are removed, which relax back to zero in an orderly way with time. Such anomalous behavior, thought to be due to gage bonding, has been reported in microstrain experiments by Thomas and verbach' who observed a negative strain of -3 X lo-' upon unloading. This kind of behavior severely limits the over-all strain sensitivity which can be achieved in such tests. The relaxation of a small positive strain subsequent to unloading in a load-unload experiment is quite normal, however, and is to be expected. The occurrence of an apparent negative strain is also encountered in those instances where the elasticity of the bonding cement is exceeded—for example 0.5 pct or 5000 pin. for cured Eastman 910. An elastic strain of this magnitude can be encountered during load-unload type testing particularly in higher-strength materials (-150,000 yield strength). During the course of microplasticity studies on pure nickel and nickel alloys,' the authors have made the following observation. In a four-point bending test, two active gages are mounted one on each side of the beam as arms R1 and R z of a conventional strain-gage bridge circuit shown in Fig. l(a). This technique provides two advantages: the sensitivity is doubled because R1 and Rz experience opposite strains and temperature compensation is provided automatically because any ambient temperature change would cause both gages to see a strain of like sign whose signals would cancel in the circuit.

Jan 1, 1964

By Morris E. Fine, Richard A. Kloske

The stress-strain beha1,ior in tension of Au-Ag alloy single crystals containing nominally 1,3, 5, 95, 97, and 9.9 at. pct Ag was studied uS strain role and lektlperalure down lo 4.2K. A slrain aging yield hob lc,rrs observed on aging under stress in the temperature range 30° lo 75°C. The species diffusing to the dislocation is thought to be a divacancy-solute complex wilh /he. solute then pinning the dislocation by short-Range ovdering and possibly Suzuki locking. At room tempevullcve the critical reso1ved shear stress .follo~c.s an empirical equation of the form tc = A +Bc' where A and B are 90 and 420 ,g per sy mm tor gold base alloys and 60 and 510 g p~r sq )11ttz .tor si1ver base alloys. This strengthening was attributed to a long-range size ejtect. The alloy slrenglliening at i.2'K is greafer than at room temperature. The additional atrloutzf was altribuled lo a uwak skovl-range i?~levacIion between the solute and dislocallon cove. The activation energy .tor deformation a/ 4.Z0h7 decreases on alloying. 11 increases irr other fee systetns. hi the 5 at. pcl Air-Ag- alloy in pmvlicular there is very extensive easy glide and lavge overshooting- of the synmetry line at 4.Z°K. There is also u sharp decrease in the vale of. strain hardenitlg near the widdle of stage II with the new rate bezng abold the sarne as tlzal In easy glide. This uws attributed to a sudden reduction of activity on the pvitrrarg sgstertr. In Au-Ag alloys the critical resolved shear stress Tc. at room temperature is essentially a parabolic function of atomic concentration:' the 50 at. pct Ag-50 at. pct Au alloy is about 10 times stronger than the pure metals. This strengthening occurs in spite of the similarity in valence and atomic size. Solid-solution strengthening in fcc metals is characteristically greater at low temperatures than at room temperature. In Ag-10 at. pct Au and Au-10 at. pet Ag; r, (20.4K)/Tc (300°K) is 2.3 and 2.5. respectively.- compared to 1.2 in pure silver.3 Suzuki' and Flinn5 explained the alloy strengthening at room temperature as a combination of Suzuki locking and short-range order hardening. The agreement between the computed and measured strengthening was very good: however, in Ag base-A1 alloys Hendrickson and Fine6 concluded that Suzuki locking resulted mainly in a yield drop effect. Recent reviews of the solid-solution strengthening in fcc metals by Fleischer2 and Haasen8, 9attributed the strengthening at room tenl-perature to the combined effect of atom nlisfit and change in shear modulus 011 the long-range stress field surrounding a dislocation. The parameter used by Fleischer was The shear tnoduli of Ag-0 to 6 at. pct Au alloys were measured by Pur-wins. Labusch. and Haasen.In While addition of 4 at. pct Au caused an appreciable increase in the C,, elastic constant. there was a decrease on increasing the solute to 6 at. pct Au: C,, and C :: were not measured in the 6 at. pct alloy. The greater solution hardening at low temperatures implies the presence of short-range interactions between the solute atoms and dislocations These include size and electronegativity effects. Whether the extra alloy strengthening at low temperatures is due to locking or friction hardening is still a controversy."".' In the present research the stress-strain behavior of Au-Ag single crystals containing 1 to 5 at. pct Ag and 1 to 5 at. pct Au was measured vs strain rate and temperature down to 4.2' K. Particular attention was paid to yield drop effects. These have not been previously reported. PROCEDURES The alloys were supplied by the Engelhard Industries. Inc.. as strips 0.050 by 0.250 by 12 in. The compositions are given in Table I. Single crystals were grown under static vacuum using a traveling molten zone technique. Crucibles shaped to the size of the strips were made of high-purity graphite prebaked for 24 hr at 1100°C in vacuum. The crucible and its charge were placed in

Jan 1, 1970

By C. F. Frey, P. J. Ahern, J. F. Wallace

THE high affinity of molten titanium for oxygen and nitrogen has resulted in considerable difficulty in developing a satisfactory melting procedure. It has been found necessary to perform melting operations either in a vacuum or inert atmos-phere, and failure to obtain a satisfactory crucible material has necessitated the use of special melting techniques. These techniques have included cold-mold arc-melting utilizing both consumable and nonconsumable electrodes, skull-melting, drip-melting, and levitation melting.' It has been recognized generally that the melting of both titanium sponge and titanium scrap would be expedited by the use of induction-melting procedures but the lack of a crucible capable of containing molten titanium without objectionable contamination thus far has prevented the use of induction-melting procedures. An extensive investigation: which included the common refractory materials was not successful in developing a satisfactory crucible for induction-melting. Some success in induction-melting has been attained with the use of a graphite crucible material, but in all instances sufficient carbon contamination was encountered to cause an appreciable reduction in the optimum mechanical properties of the titanium or titanium alloys. These investigations"" report an increase in the carbon content from approximately 0.3 to 1.0 pct. A serious reduction in the tensile and forming properties has been observed as a result of this carbon contamination. The development of a satisfactory induction-melting procedure for titanium without undue contamination undoubtedly would have considerable economic significance. Such a process would be particularly useful in melting the large quantities of low-cost scrap now available that can only be reprocessed at considerable expense and difficulty by the more elaborate techniques referred to previously. In addition, the process could provide a satisfactory method of melting and alloying of bri-quetted sponge for forging ingots.

Jan 1, 1959

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

The Subcommittee on Manganese, of the A.I.M.E. Committee on Industrial Preparedness, prepared under date of Jan. 24, 1924, for and at the request of the War Department, a confidential report on manganese as an element in the problem of national defense. This report was later released and published, in slightly modified form, as a separate pamphlet. After the lapse of eight years, in view of the vital position of manganese in the problem of industrial preparedness agenist a war emergency, the War Department made a request to have the onclusions of 1924 reviewed and brought up to date. To comply wi' this request the manganese subcommittee was reconvened and ex' tive studies were once more made of the entire subject of mang? . A new report, with specific recommendations, was submitted + War Department in February, 1932. This second report, with 4. L specific conclusions and recomrnendations expressed to the War Department omitted, has now been released and is hereby published. Following a rather brief discussion of uses of manganese and classification of manganese ores, requirements and sources are dealt with at some length. Domestic ferro-grade reserves are estimated on the basis of price and are shown by means of a curve where tons of metallic manganese are plotted cumulatively against prices ranging from 50¢ to $1.00 per unit; thereby indicating at a glance the tonnage which the Committee believes would become commercially available at any particular price per unit. Foreign sources of ore are described and foreign prices which the domestic producer must meet are considered. The question of a war-emergency reserve is then analyzed, requirements are balanced against apparent resources, and the principal conclusion that emerges is that a war reserve or stockpile is still vital to national defense.

Jan 1, 1934

By P. A. Beck

In the course of work on grain growth in high purity aluminum a simple optical method was developed for detecting the presence or absence of preferred orientation in annealed specimens. The specimens were prepared by grinding, polishing and "deep etching." The etching reagent used for high purity aluminum has been described.* The resulting etch pits produced selective

Jan 1, 1949

By R. H. King

This paper describes the results of an underground coal mine trial installation of a shielded trailing cable. The cable was a three conductor, round, type SHC-GC and was installed on a shuttle car in a conventional room-and-pillar mining section. The purpose of the study was to evaluate proposed legislation that would require shielding on low-voltage trailing cables. Such legislation would require machine modifications to cable reels, packing glands, and couplers; increase cable splicing complexity; and necessitate additional splicing materials and training. Furthermore, fault location might be more difficult. Even though shielding will cause some problems for the mine operator, it can reduce electrical shock hazard to mine workers. This paper presents information that mine operators can use to solve most of the problems encountered if they are required to install shielded cables. The in-mine evaluation was funded by the US Bureau of Mines; however, the views and conclusions in this paper are those of the author and should not be interpreted as necessarily representing official policies of the US government.

Jan 1, 1982

By G. T. Lineberry, L. Adler

Due to safety-imposed constraints on clearances for mobile bulk handling equipment, it is necessary to optimally select a unit based on speed and size. The unit cannot be both large and fast. Since output is proportional to both size (or capacity) and speed, the combination must be carefully examined to maximize output. A simple graphical procedure and a calculus-based solution are presented to accomplish this. While the procedure applies to all mobile bulk handlers, as an example of the solution technique, attention is focused on shuttle cars. Background Major variables To fully define a bulk handling problem, the conditions, equipment, and activities must be characterized. The conditions and activities, when lumped together, are termed "encumbered space," since they "act to impede motion, as with a burden" (Lineberry, 1979). The insertion of mobile bulk handling equipment into what is already a difficult set of conditions and activities compounds the state of encumbrance, as limited space is competed for by many normal and life support systems. Long (1972) recognized the effects of design criteria, including road width, on haulage vehicle speed and, therefore, on production. Velocity-clearance curves Velocity-clearance curves are either available or can be constructed in the field. A preliminary set of curves for average conditions and activities is shown in Fig. 1, where clearances are only for the side of the vehicle (Lineberry and Adler, 1984). These curves set the safe speed limits for a vehicle operating at given clearances, under given conditions and activities. When feasible, velocity-clearance curves should be constructed through field measurement and observation. Curve construction should also consider haulway roughness, distances, and operator skill, as well as loading and dumping characteristics. It should be noted that haulage capacity determination is a total systems problem, not one just dependent on velocity and clearances. Production requirements and company capabilities also influence capacity determination.

Jan 1, 1986

By L. H. Lange

It is the author's opinion, based on many field experiences over several years, that it is usually better to design a rougher flotation circuit with long rows of rougher cells for high tonnage capacity for maximum recovery and better operating efficiency than the alternative of a greater number of shorter rows with proportionately less tonnage of feed per row. Recent plant studies and tests in the 12,000 ton per day flotation plant of the Atlas Consolidated Mining and Development Corp., Cebu, P. I., have given further substantial support to this opinion. There are two flotation sections in this concentrator: 1) Section 1, treating half the tonnage to the total mill, has eight rows of rougher cells, each row containing 360 cu ft of cell volume. Accordingly, each row of cells receives, on the average, 750 tons per 24 hours which assays about 0.65 to 0.75% copper. The main copper mineral is chalcopyrite with minor

Jan 11, 1963

By D. J. Sellmyer

In order to orient single crystals by the back-reflection method it is necessary to know the angles between the various crystallographic planes. These angles have already been published for the hexagonal close-packed metals magnesium, zinc, and cadmium.'

Jan 1, 1965

By W. D. Douglas, M. J. Hampshire, G. J. C. Young

This paper describes the replacement of a conventional filtration, clarification, and zinc precipitation plant by a carbon-in-pulp (CIP) electrowinning plant, with the objective of improving the recovery of gold from cyanide leached, acid plant calcines. The discussion covers early laboratory studies to the design and erection of the full-scale plant. Particular emphasis is placed on the problems encountered with commissioning and the strategies employed to solve them.

Jan 1, 1985

THE TRANSACTIONS of the Institute for the early years display but Little interest in physical metallurgy-indeed, it is striking how thoroughly process metallurgy absorbed attention until quite recent years. The first volume carries no article that can be strictly described as physical metallurgy, unless one on the rolling and hammering of ingots be doubtfully so described. Nor does the second volume contribute more the interest then was in mining, and in production methods, both ferrous and nonferrous, with much attention to the new methods of making steel. The third volume records papers on: the condition of carbon in gray and white iron, a paper devoted to chemical rather than microscopic analysis; the annealing of spiegeleisen; phosphorus and carbon in iron and steel, similarly chemical. Much attention was given, and continued to be given for years, to the manufacture and behavior of rails. The question of the nature of steel appeared early (Vol. 11)-What is Steel, by A. L. Holley-where arguments on nomenclature were already active; and Holley also bemoans, in modern spirit, the Inadequate Union of Engineering Science and Art; Pearse wrote on cast iron for guns (reflecting again the ironic beneficence of war in metallurgy), and said that Captain Walbach was the first to insist on chemical analysis of gun irons; he quotes Major Wade's study of comparative hardness, using penetration hardness measurements (Brinell was to come later), and quotes the important Reports on the Strength and Other Properties of Metals for Cannon, by H. C. Baird, Philadelphia, 1855, in which the advanced state of tensile testing at the time is shown. Hewitt, in Vol V, comments upon the function played by technical schools and technical societies upon the growth of metal-

Jan 1, 1948

Copper from Central Africa was well known to the Arab slave traders who depredated the country in the nineteenth century. By the 1870's slave raiding was so intense that the habits of the tribes were disrupted, and they no longer worked the copper deposits or made the crosses and bars of copper which had been their custom. In fact, the country had been greatly depopulated by the slave raiders. News of this horror was spread to the civilized world by missionaries and, in particular, by David Livingstone's writings. Whether to extend geographic knowledge, to suppress slavery or for national aggrandizement, the rush for African territory was on at the end of the nineteenth century. Cecil Rhodes at this time was established by his successes in diamonds and gold. He obtained the blessing of Lord Salisbury in 1889 to form the British South Africa Company under crown charter. His objectives were to occupy the lands north of the Zambezi for England and pay for development out of the country's mineral deposits. He planned to occupy the territory and close the gap to form an all-British route from the Cape to Cairo, one of his great dreams. With this master plan in mind he sent his agents into the field to make treaties with the tribes.

Jan 12, 1962

Teamwork: The famous first sentence of an essay en- titled Aphorisms, by Hippocrates, is as follows: "Life is short, the Art long, opportunity fleeting, experience treacherous, judgment difficult." The future of science does not depend so much on the number of scientists or the number of colleges, but rather on the individual qualities and the degree of perfection of a limited group of leading scientists and colleges. These are individual factors which require inherent talent which in turn is a condition evolved after generations of culture. Thus, very elaborate higher education for indiscriminate masses of humanity or students may not necessarily show the expected results. In other words, it is possible that higher specialized education should be given only to the few talented individuals, and their capacity and worth should be judged by as highly qualified and talented teachers. Quality is the greatest of all competitive aids. An essential qualification that must be possessed by a quality mineral industries college is a high caliber teaching staff, for the mineral sciences will advance in the coming years only if the leading minds of today are made avail- able as the mental springboards for our scientists of tomorrow. Mineral industries schools are finding it increasingly difficult to maintain a high caliber staff of instructors and administrators in competition with private business and governmental demands for similar

Jan 1, 1950

By Dwight K. Smith

A new pozzolanic composition has been developed for cementing oil wells where moderate to high temperatures prevail. This material is an entirely different concept to other oil well cementing materials, such as portland cements, cements containing additives, or liquid resins. Its characteristics are such that it is not, at present, recommended for use at temperatures less than 140º F. It can he either accelerated or retarded across a wide range of well conditions. This new cement is composed of a pozzolanic material, hydrated lime, and a chemical activator to give it early initial strength. This material can be used in wells from 6,000 to 18,000 or more feet where temperature conditions are similar to those along the Gulf Coast. This cement, when set, has no soluble portion subject to leaching or any compounds that should be attacked by sulfate waters or brines. For this reason, it should be permanent when placed adjacent to formations carrying any type of fluid. The compressive strengths in 24 hours are more than adequate for wells where temperatures are 140°F and higher. These values ore in excess of many other types of cementing composition presently in use in the field. This pozzolanic composition does not retrogress in strength at high temperatures as do some other types of cementing materials. The slurry weights of this material will vary slightly according to the specific gravity and water requirements of the pozzolnn itself. The materials covered herein will mix from 13.5 to 14.3 lb/gal, and will have a waiting-on-cement time comparable to other materials used under the same conditions. Economically speaking, this composition is less expensive than either portland cements or retarded cements presently being used under deep well conditions. INTRODUCTION Pozzolans are siliceous material which, though not cementitious in themselves, contain constituents which at ordinary temperatures will combine with lime in the presence of water to form compounds which have a low solubility and possess cementing properties. The use of pozzolanic materials dates back many hundreds of years and both the ancient Greeks and Romans were aware that certain volcanic deposits, if finely ground and mixed with lime and sand, yielded a mortar which possessed special properties. Generally, the early strengths of such materials were rather weak and were considered insufficient for modern commercial usages. Pozzolanic materials have been used extensively with portland cement in mass concrete to obtain special properties. In recent years, large quantities of certain pozzolanic materials have been used successfully admixed into portland cements for oil well cementing. Pozzolans, being reactive silicates, will combine with the free lime that is an inherent component of set portland cements and thereby. becomes cementitious themselves. POZZOLANS FOR OIL WELL CEMENTING There are many types of pozzolans, some of which are more reactive than others. The quality of the pozzoIan depends on the degree of reactivity, chemical composition, fineness, and other less well understood factors. Some of the more widely accepted pozzolans are those classified as fly ashes, while others are certain materials of volcanic origin. pozzolans which require large vol-

Jan 1, 1957