Search Documents

By K. U. Snowden, J. N. Greenwood

CRACKS which form in lead exposed to fluctuating stress frequently follow a rectangular pattern. It is well known that under ordinary atmospheric conditions these cracks are intercrystalline. On the other hand after fabrication the crystal grains in lead are in general irregular polygons. The observed facts appear to be mutually contradictory. Re-examination of some lead failures has confirmed that the rectangular cracks are intercrystal- line. It follows therefore that under fluctuating stress some of the grains lose their irregular outlines and become approximately regular polygons of cubic type. G. R. Gohn and W. C. Ellis* suggest that this is due to recrystallization during the life of the part, in such a way that the new grain boundaries are aligned at 45 deg to the longitudinal strain prior to the formation of the fatigue crack. Experiments at Baillieu Laboratory—Some recent experiments carried out in the Baillieu Laboratory in conjunction with the Broken Hill Associated Smelters have thrown some light on this transition. A test piece of pure lead was polished chemically

Jan 1, 1959

The first production on the Island of Trinidad was discovered 29 years ago; 13,275 acres were proved for oil and gas to the end of 1937, and 145,076,700 bbl. was produced from 2661 wells, or 10,928 bbl per acre. The production of oil in 1936 was 13,237,030 bbl. and in 1937 a new peak of 15,498,350 bbl. was reached. During November 1937, the daily average production was 43,350 bbl., or 35 bbl. per well, while the maximum gas production was 45 million cubic feet daily. Two hundred fifty wells were completed during 1937 and 15 abandoned. At the end of last year, 800 wells had been temporarily shut down, 1235 were producing oil and gas, and 2 were producing gas only. Six hundred seventy-nine dry wells had been drilled to the end of 1937. At the end of November 1937, the following oil-producing methods were in use: 395 wells flowing, 491 pumping, 97 on air-gas lift and 252 wells miscellaneous. There were no flooding operations. The oil is produced from the Miocene and Eocene and is of both asphalt and paraffin base. The gas produced averaged approximately 1050 B.t.u. per cu. ft. with 0.8 gal. of gasoline per 1000 cubic feet.

Jan 1, 1938

By E. N. Silverman

Mixtures of' MnS, ZFeO-SiO,, ZMnO.SiO, FeO, and MnO were prepared synthetically and used to study the planes ZFeO. Si0,-ZMnO.SiO,-MnS, FeO-MnO-MnS, and Fe0-MnO.Si0,-MnS in the quaternary system. Because the oxides and silicates studied flux MnS, inclusions in this system are partly liquid during rolling. Also, oxygen can modify subsurface inclusions through the reaction MnS + FeO—FeS + MnO during the soaking of ingots and the reheating of blooms and billets. NONMETALLIC inclusions in steel have long been a subject of study and conjecture because the properties of many steels are known to be affected by the the kind and amount of inclusions present. In free-machining steels, the type of inclusion present has a direct bearing on their machinability; in other steels, cleanliness is important and metallurgists direct their efforts at reducing the amount of non-metallic inclusions. Thus, the accumulation of knowledge about the formation and behavior of inclusions during all stages of steelmaking and processing should aid in improving the quality of steels and decreasing the production costs resulting from rejections. Previous studies of inclusions have contributed greatly to our understanding. The investigators have generally examined inclusions in finished steel. Boulger, Moorehead, and Garvey1 found that in Bessemer steels, low silicon contents results in globular sulfide inclusions with attendant high machin- ability ratings. Van vlack2 also found that low silicon contents favor inclusion morphology that contributes to high machinability ratings. Boquist and Stoll* found that silicon content affected sulfide inclusions and machinability of blooms, billets and bars more than did the finishing temperature in the range between 1775° and 2075°F. Carney and Rudolphy3 studied the distribution of sulfur, manganese, silicon, and carbon in a commercial ingot of resulfur-ized steel and found that silicon was concentrated near the bottom. This helped to explain why bottom cuts had poorer machinability. Klinger and Koch4 developed techniques for extracting inclusions from steel, and the technique devised by Gurry, Chris-takos, and stricker5 for extracting carbides can also be adapted to the study of inclusions. A different approach to the study of inclusions in steel consists of synthesizing the constituents that form inclusions and determining the phase eauilibria in the system that contains the constituents. The resulting phase diagrams can then be used to determine the effect of the various constituents upon each other. In this way, it becomes possible to under-

Jan 1, 1962

By J. D. Alexander, W. L. Martin, J. N. Dew

This paper presents data obtained using a flood-pot technique to determine the fuel available and the corresponding theoretical air requirements for in situ combustion of crude oils. Since the technique is relatively quick and easy, it is a practical and convenient tool for evaluating reservoirs as fireflood prospects. It is also a research tool which facilitates systematic study of the variables affecting fuel availability and corresponding air requirements. The understanding of these variables is of prime importance to those concerned with the technical and economic development of in situ combustion as an oil-recovery process. The experimental results show conclusively that the fuel available for in situ combustion is not a constant but, rather, varies with crude-oil characteristics, porous-medium type, oil saturation, air flux and time-temperature relationships. Thus, the fuel availability for specified field applications should be determined using actual reservoir crude and core material and the process conditions expected during in situ combustion in the reservoir. INTRODUCTION In situ combustion is a thermal process for recovering crude oil from reservoirs. The thermal energy released during the combustion of a small amount of the oil in place aids in the displacement of the remaining oil. Numerous articles have been published describing the in situ combustion process giving detailed results of laboratory and field experiments.10 In order to engineer an in situ combustion project, a number of important factors must be considered and determined. These factors include: (1) the amount of fuel consumed per unit of reservoir volume swept by the combustion zone, (2) the composition of the fuel consumed, (3) the amount of air required to consume this fuel, (4) the portion of the reservoir swept by the combustion zone, (5) the appropriate air-injection rates and pressures, (6) the amount of oil that will be recovered, (7) the rate of oil production and (8) the operating costs. Nelson and McNiell1 recently have described a procedure which utilizes laboratory combustion-tube data as a basis for the calculation of some of these design factors. Various authors have attempted to describe the in situ combustion process mathematically, and considerable progress has been made. Analytical solutions to the problem of heat transfer from a moving combustion front have been obtained for linear and radial systems."-' All of the published results involve the assumptions that: (1) fuel concentration is constant throughout the reservoir, or that fuel concentration is inversely proportional to the velocity of the front for a given rate of oxygen consumption; and (2) the fuel reacts instantaneously with injected oxygen, while liberating a constant amount of heat per unit weight of fuel at all temperatures. It seems both desirable and reasonable to test the validity of these assumptions experimentally. This paper presents laboratory data which were obtained by means of a "fire flood-pot" method for determining fuel availability and composition, and the corresponding theoretical air requirements for in situ combustion of crude oils under variable conditions. The mechanics of the method are similar to a conventional tube-run experiment.' The important differences involve the size of the reservoir model used and the method for providing the experimental environment. The new method subjects conventionally-sized core samples or unconsolidated sands to a programmed environmental sequence similar to that experienced by a similar volume of rock during the approach and passage of a combustion front in a long tube or in an oil reservoir undergoing in situ combustion. Restored-state samples can also be used. The small samples and relatively simple techniques involved allow an experiment to be set up, run and calculated in about three 8-hour days. This is a considerable improvement over long-combustion-tube techniques which can require several days to run and several more work days to set up and calculate. All the runs presented were run at 40-psig injection pressure. Pressure was not considered as a variable for these experiments, since we previously had found that it had only a small effect on fuel availability up to 600 psig.APPARATUS AND MATERIALS APPARATUS The fire flood-pot apparatus consists of a consolidated

By G. M. Swinkels, A. Vizsolyi, E. Peters

A process is described utilizing ferric chloride leaching followed by reduction of the cupric content to cuprous by cement copper, with CuCl obtained thereafter by crystallization. The residual liquor is cemented with sponge iron to produce cement copper and a copper free ferrous chloride solution. The latter is oxidized in an autoclave with oxygen to regenerate ferric chloride and to precipitate excess iron as a granular, filterable hematite. Cuprous chloride crystals are reduced to high purity metal with hydrogen, while sulphur reports almost quantitatively in residues in the elemental form. Pyrite and molybdenite are not leached. This paper describes the important variables in the process, as well as the deportment of minor elements as silver, gold, selenium, tellurium, bismuth, nickel, lead, zinc, magnesium, etc. An elegant method of isolating silver from CuCl crystals is described, as well as recovery of gold from residues by a chloride reagent The process is described as non-polluting and capable of producing refined copper, ore grade iron oxide, elemental sulphur, and yields of minor metals as good or better than obtainable by conventional smelting, without the use of solvent extraction or electrochemistry.

Jan 1, 1981

By D. C. Hilty, W. Crafts

J. Chipman—It has been my privilege to discuss this work with the authors on several occasions and to observe at first hand the experimental methods employed. I wish, therefore, to emphasize certain points which they have mentioned only briefly with regard to the experimental techniques. The rotating induction furnace as here employed interposes liquid metal between slag and refractory thus preventing the two nonmetallic parts of the system from reaching equilibrium with one another. It is therefore impossible for the metallic phase to be completely in equilibrium with both the slag and the crucible. The metal also acts as a partially permeable membrane allowing certain components, including oxygen, to diffuse from slag to crucible. This transfer results in building up on the face of the crucible a layer of material whose composition is in part dependent on that of the bath. Reactions between the layer and the solid refractory are slow, as evidenced by the rather good life of the crucible. Hence it seems probable that the layer is more nearly in equilibrium with the metal than with the underlying crucible material and that, once it is established under a bath of a given composition, its further reactions with that bath are slow. Additions to slag or bath may be followed by changes in the layer; and time must be allowed for virtual completion of such changes, before it can be assumed that slag and metal are in equilibrium. We may judge from the results reported that, in general, this was the case and that the data represent at least quite close approximations to slag-metal equilibrium. Data on deoxidation and on oxygen solubility are no better than the analytical methods employed. The vacuum fusion method as used by the authors seems entirely adequate for the samples analyzed. I have had frequent occasion to compare results with their laboratory, always with very satisfactory agreement. The determination of aluminum at very low concentrations is perhaps an even more difficult procedure. Here also the colorimetric method used has been worked out with great care and is undoubtedly the most dependable method available. The discrepancy between observed and calculated deoxidation or solubility lines is not to be explained as the result of experimental errors, either in the sampling or analysis of the metal. Nor is it to be blamed upon inaccuracies in the several kinds of indirect data upon which the calculated results were based. It is true that both the observed and the calculated lines admit of some uncertainty as to their exact locations, but the uncertainties are small compared to the wide gap which separates the two lines. The authors have pointed out the real cause of the discrepancy. In all of their experiments the solid phase was not Al2O3 but a mixed oxide containing iron and aluminum. This suggests an extension of the calculated values to include equilibrium with the spinel FeO . A12O3. The free energies of FeO and A12O3 are known, that of the spinel is not. However, it cannot differ greatly from that of its component oxides for even in the more stable spinel, chromite, the free energy of formation from the oxides is less than 10,000 cal. For purposes of calculation we shall call this free energy X and solve for values of X lying between zero and 10,000 cal. The other data required are taken from the forthcoming revision of "Basic Open Hearth Steelmaking" and are given in the following equations in which underlined symbols indicate elements dissolved in liquid steel and the standard concentrations are 1 pct. ?F° at 1600°C, cal ?LA = 2 Al + 3 O; + 107,200 FeO = Fe + 0; + 5,460 FeO + A12O3 = Fe + 2A1 + 4 0; + 112,660 — X The corresponding equilibrium concentrations are shown in fig. 21. The line marked A12O3 corresponds to the first equation, those marked FeO . AL2O3 correspond to the last, with X = 0, 5000 and 10,000 cal, respectively. The two upper lines represent the data of Hilty and Crafts and of Wentrup and Hieber. The points are the observations of Hilty and Crafts in the presence of 0.50 pct Mn.

Jan 1, 1951

By Eugene McAuliffe

The mining press, as well as certain federal and state bulletins, refer from time to time to the relative hazards that attach to loading bituminous coal by hand when compared with the so-called "mechanical loading" process. Much of the coal coming under the head of hand-loaded coal is won in part by the use of machinery; the coal-cutting machine is in general use, the electric power drill employed to a lesser extent. Therefore it may be said that the principal difference in the process employed, mechanical loading versus hand loading, lies in the fact that some type of loading machine is employed in the mechanical loading process to lift the coal from the face of the room, place or entry, after it is mined, placing it in the pit cars for transport to the tipple. It is a common practice to compute accident records on the basis of tons mined per fatal and per nonfatal accident, disregarding the fact that it is possible to produce by the aid of coal-loading machines the same daily, monthly and annual tonnage with a much smaller force than is required where the coal is all shoveled by hand. Inasmuch as the men who are released by the substitution of machinery for hand labor must find employment elsewhere, suffering some measure of hazard in their new occupation, we are of the opinion that the true relative hazard that attaches to the processes of mechanical loading and hand loading can be determined only by using as the basis of comparison "man shifts worked" or "hours of exposure" experienced per accident. The Union Pacific Coal-Co., beginning with the year 1929, undertook to maintain a true record of man shifts worked per compensable accident, giving equal weight to fatal and nonfatal accidents. Accidents lacking sufficient severity to come under the compensable terms of the Workmen's Compensation Act were not included in the compilation, the Act providing that "no compensation, except the expense of medical attention, shall be allowed for the first seven (7) days of disability, unless the incapacity runs beyond the period of twenty-one (21) days, in which case the compensation shall run from the time of the injury." With the further thought that all accidents suffered by employees engaged in any service, in or about the place where the loading process

Jan 1, 1931

By Dewitt T. Ring

Reliable and detailed data covering the enormous number of wells drilled and the long historical production of the state, many of which were never recorded until recent years, render it impossible to gather statistical material suitable for the Institute's standardized form. The total production of crude oil in Ohio for the year was 3,654,503 bbl., which is less than the total production in the United States for the peak day of August 1937. For a period of eight years, from 1895 to 1902 inclusive, Ohio produced more oil than any other state. During the year, 1271 tests were drilled in the state, or 114 more than in 1936. Of these, 317 were oil wells, with an initial production of 7088 bbl., an average of 22.3 bbl. per well; 503 were gas wells, with an initial open flow of approximately 222,441 M cu. ft., or 443 M cu. ft. per gas well drilled; 451 were dry holes, that is, 35 per cent of the total completions. A number of factors account for the steady decline of oil production in Ohio. In the state, at the close of thc year, there were fewer than 28,122 producing oil wells. In 1936, there were 30,150 operated oil wells with an average yearly production per well of 126 bbl. The production for 1937 averaged 130 bbl. per well. During the year, 2028 oil wells were abandoned. In other words, old wells are being abandoned more than six times faster than new ones are being drilled. Since the inception of the oil and gas industry in Ohio, between 150,000 and 160,000 wells have been drilled in the state; new potential territory, offering desirable locations for either oil or gas, is becoming increasingly more difficult to find; the dry-hole percentage will continue to increase. Prices Another factor directly affecting the crude situation during the year was the matter of price and proration of Pennsylvania grade oil. The posted price for Pennsylvania grade in Ohio on June 7 was $2.37 per barrel; at the close of the year, it was $1.70 per barrel, or a reduction of 28 per cent in price. In addition to this price cut, a 50 per cent pro-

Jan 1, 1938

By Edna A. Dancy, Gerhard J. Derge

The specific conductance of FeOx,-CaO melts in contact with iron was found to decrease from 200 ohm-1 cm-1 for FeO, to 40 ohm-1 cm-1 for a melt containing 26.3 pct CaO at 1400°C. The temperature coefficient was positive at all compositions, but became smaller at high CaO contents. Current efficiencies for electrolysis increased from 2.5 pct in FeOx to 17.3 pct at the high CaO composition, indicating a change from predominantly electronic conduction to conduction with a substantial ionic contribution. It was shown that Ca++ ions as well as Fe++ ions carry the ionic current. A subsidiary investigation on the apparent effect of atmospheres of argon, helium, and nitrogen on the electrical conductivity showed that this could be correlated with surface temperature losses, which varied with the thermal conductivities of the gases and resulted in precipitation of metal by the reaction 3 Fe++ = 2 Fe+++ + Fe. The work described in this paper is offered as a contribution to the general fund of knowledge concerning metallurgical slags. Measurement of electrical conductivity and electrolysis are comparatively trouble -free methods for investigating molten materials, but, although these methods had been used for complex slags, it was not until the work of Bockris et al.1 that the approach of examining simple binary slag systems was employed, and CaO-SiO2, MnO-SiO2, and Al2O3-Si9 were studied. Two groups have performed work of particular relevance to the present investigation. Inouye, Tomlinson, and chipman2 studied the conductivity of wustite as a function of temperature and of the addition of 5 mol pct of a number of oxides, including CaO. They concluded that molten FeOx in equilibrium with iron is a semiconductor. Simnad, Derge, and ceorge3 demonstrated the ionic nature of liquid iron silicate slags and also concluded that, although the conductivity of FeOx in equilibrium with iron is predominantly electronic in nature, there is a small ionic contribution. The work reported here on FeOx,-CaO slags consists of three main parts, namely, the determination of the specific conductance over a wide composition range, an investigation into the nature of the conductivity through current-efficiency measurements over the same composition range, and an attempt to identify the current-carrying ions, as well as a subsidiary investigation on the apparent effect of the nature of the inert atmosphere on the conductivity. EXPERIMENTAL Materials. The slags, varying in composition from FeOx to 27 pct CaO, were prepared by heating reagent- grade Fe2O3 in an ingot iron crucible with a suitable amount of CaCO3 and, in some cases, powdered iron, in air. This prefused material was then used for the runs. At the end of each run the cell was removed from the furnace and quenched by immersing the bottom half in water. After crushing, the slags were analyzed for calcium and total iron by the usual wet methods. The oxygen content was obtained by difference. Specific Conductance: Apparatus and Method. Fig. shows the experimental setup, with the conductivity cell and leads of ingot iron. The standard four-probe method for measuring high conductivities was used. In this, the potential drop across the unknown resistance is compared with the potential drop across a known resistance connected in series, i .e., same current through both resistances. Thus there are both current and potential leads to the center electrode and to the crucible, which acts as th other electrode. Both ac and dc circuits were available for the measurements; they have been described in earlier work performed in this laboratory.4,5 The geometry of the cell was such that the center electrode was equidistant from the bottom and sides of the crucible. This ensured that the current path was the same irrespective of the magnitude of the conductivity of the material in the cell. Cell constant were measured with KC1 or NaCl solutions, which have considerably lower conductivities (0.0013 to 0.25 ohm-' cm) than the slags, and this precaution in design made sure that the determined cell constants applied to the cells with contents of any conductivity. The cell-constant determinations were made with the ac measuring circuit to prevent polarization. The four-probe method eliminates lead resistance but not the resistance of those parts of the center

Jan 1, 1967

By O. U. Bradley

THE methods of handling the oil output of the mid-continent fields are not unlike those practised in other oil fields of the United States, and it is not expected that this paper will present any entirely novel ideas. Some features of the practice of handling this oil may be of interest, however. WOODEN CAGING TANKS Practically all of the oil sold to pipe lines and other purchasing agencies throughout the Mid-continent field is gaged from wooden tanks. Steel gaging tanks are slowly coming into use, and are preferable in many ways-leakage and evaporation are reduced, and the strapping and recalculation of capacities are unnecessary. The wooden tanks are slightly coned to facilitate tightening the hoops. The-sizes in, common use are 250, 500, 800 and 1600 bbl. The number and the capacity of the gaging tanks upon any producing oil property depend upon its production, and the facilities for disposing of the output. The 1600-bbl. size was the most common in the Cushing field, particularly during the period of flush production. The tanks are distributed over the leased premises in groups of two, three, and four tanks each, and these are filled from flow tanks, or through direct pipe connections with the heads of the wells. Flow tanks are merely temporary reservoirs to facilitate the transfer of oil from the wells to the gaging tanks. They diminish fire risk,, and are considered indispensable on small producing properties where .water is pumped with the oil, as they permit the refuse and water to settle out before the production is run to the gaging tanks.

Jan 3, 1918

By J. N. Hobstetter, J. J. Becker

Deformed copper single crystals exhibited, upon annealing, a recrystallized twinned grain with a twin plane parallel to an active deformation plane, rotated approximately 22" about its pole, or else did not recrystallize at all. If extraneous deformation was not carefully removed, no simple orientation relationship was found. RECRYSTALLIZATION textures have been a subject of practical interest for many years, but any real understanding of their formation will have to start with a study of the recrystallization of carefully deformed single crystals. Some efforts have been made in this direction,'-' but much more experimental information is needed before a satisfactory picture of the crystallography of recrystallization can be formed. This paper reports a few results in copper single crystals. The crystals studied in this investigation were grown by the Bridgman method," and their orientations determined by the back-reflection Laue technique." Some specimens were simply deformed in compression, others were sheared, and still others tested in a rotating-grip device, in attempts to remove end constraints. The details of their deformation behavior are described elsewhere.' The deformed specimens were annealed and the orientations of the recrystallized grains were determined optically, as described by Barrett and Levenson.8 Compressed Specimens Specimen 17-A, whose orientation is given in Fig. 1, was compressed to a total of 19 pct. As observed before,' increasing deformation took place by increasing density of slip lines in initially formed clusters, with little if any formation of new slip clusters in unslipped areas. The specimen was then etched in nitric acid until its length had been reduced from 0.766 to 0.735 in. It was annealed at 1000°C, in increments of a few minutes. After 63 min, two small grains had appeared in the center, Fig. 2. They were found to be twinned with respect to each other (AB, Fig. 4). After 30 min more, the specimen was completely recrystallized. A typical view of it is given in Fig. 3. A summary of all orientations found is given in Fig. 4, in which the prominent grain G is in (001) standard projection, and the poles of the active slip planes after deformation are indicated by SP (primary slip plane), CrSP (cross-slip plane), and CnSP (conjugate slip plane). All the orientations found were related through seven orders of twinning. A "family tree" of these twins is given in Fig. 5. Furthermore, the BG twin composition plane lies close to the cross-slip plane

Jan 1, 1954

By C. W. Sherman, J. Chipman, H. I. Elvander

THE pronounced and usually deleterious effects of sulphur on all ferrous metals and the resultant necessity for its control in metallurgical processes have stimulated many investigations of the system iron-sulphur. The data required for thermodynamic study of the behavior of sulphur in molten iron and steel include the activity and free energy of the dissolved sulphur and its heat of solution. Such data are also of theoretical interest since there is all too little information available concerning solutions of nonmetallic solutes in metallic solvents. It was the purpose of this investigation to attack the problem very directly by a study of equilibrium at several temperatures in the reaction H2 (gas) + S = H2S (gas) [1] K1 = PH2S /PH2 as where the sulphur is present in the liquid iron in amounts up to several percent by weight. Such a method of attack is not new since several careful studies have already been reported. It is planned, however, to extend the study to other metallic solvents and particularly to determine the effects of the various alloying elements on the activity of sulphur in liquid iron. This paper presents the results on molten iron-sulphur alloys containing up to 4 pct sulphur in the temperature range 1530°-1730°C. Literature Review The significant researches on dilute molten solutions of sulphur in iron include those of Chipman

Jan 1, 1951

By Clark A. Sumner, D. Arthur Burnham

A process for recovery of greater than 99% of the copper contained in acid leach solutions by sulfide precipitation using hydrogen sulfide as a hydrometallurgical reagent has been developed. The process incorporates the concept of hydrogen sulfide addition to recycled copper sulfide solids in a turbulent flow area where further precipitation or agglomeration occurs to increase the effective particle size of the copper sulfide precipitate. Because the recycled solids provide a larger number of particles upon which momentary excesses of hydrogen sulfide are absorbed, oversulfidization of the product is prevented. Copper sulfide precipitates produced in this manner in a laboratory test reactor showed greatly improved physical characteristics compared to copper sulfide precipitates obtained by conventional direct precipitation in which H2S is bubbled directly into acid leach liquor. Copper sulfide precipitates were evaluated and compared by use of filtration tests and settling rate studies. Electron microscopic examination of the solids confirmed the presence of larger particles in reactor-precipitated copper sulfide. Flotation was examined as an alternative to filtration for recovery of CuS precipitates and was found to achieve complete CuS removal without addition of collector or frothing reagents in a period of 2 min. In the same test reactor, a rapidly floatable CuS precipitate was also formed by mixing H2S with acid liquors used to leach crushed copper oxide-copper sulfide ore (LPF process). In the presence of gangue from the crushed ore, flotation of both natural and reactor-produced copper sulfides resulted in recovery of better than 90% of the copper contained in the crushed ore.

Jan 1, 1974

By K. E. Brown, G. H. Fancher

An 8,000-ft experimental field well was utilized to conduct flowing pressure gradient tests under conditions of continuous, multiphase flow through 2 3/8-in. OD tubing. The well was equipped with 10 gas-lift valves and 10 Maihak electronic pressure recorders, as well as instruments to accurately measure the surface pressure, temperature, volume of injected gas and fluid production. These tests were conducted for flow rates ranging from 75 to 936 B/D at various gas-liquid ratios from 105 to 9,433 scf/bbl. An expanding-orifice gas-lift valve allowed each flow rate to be produced with a range of controlled gas-liquid ratios. From these data an accurate pressure traverse has been constructed for various flow rates and for various gas-liquid ratios. A comparison of these tests to Poettmann and Carpenter's correlation indicates that deviations occur for certain ranges of flow rates and gas-liquid ratios. Numerous curves are presented illustrating the comparison of this correlation with the field data. Poettmann and Carpenter's correlation deviates some for low flow rates and, in particular, for gas-liquid ratios in excess of 3,000 scf/bbl. These deviations me believed to be mainly due to the friction-factor correlation. However, Poettmann and Carpenter's correlation gives excellent agreement in those ranges of higher density. This was as expected and predicted by Poettmann. He pointed out that their method was not intended to be extended to those ranges of low densities whereby an extreme reversal in curvature occurs.l As a result of these experimental tests, correlations using Poettmann and Carpenter's method were established between the friction factors and mass flow rates which are applicable for all gas-liquid ratios and flow rates. Definite changing flow patterns do not allow any one correlation to be accurate for all ranges of flow. INTRODUCTION The ability to analytically predict the pressure at any point in a flow string is essential in determining optimum production string dimensions and in the design of gas-lift installations. This information is also invaluable in predicting bottom-hole pressures in flowing wells. Although this problem is not new to industry, it has by no means been solved completely for all types of flow conditions. Versluys,2 Uren, et al, 3 Gosline,4 May,5 and Moore, et al,6,7 were all early investigators of multiphase flow through vertical conduits. However, all of these investigations and proposed methods were very limited as to their range of application. Likewise, many are extremely complicated and therefore not very useful in the field. Only in the last decade have any significant methods been proposed which are generally applicable. The most widely accepted procedure in industry at the present time is a semi-empirical method developed from an energy balance, proposed by Poettmann and Carpenter8 in 1952. Their correlation is based on actual pressure measurements from field wells. Accurate predictions from this correlation are limited to high flow rates and low gas-liquid ratios. Although this method will be discussed in detail later, it should be pointed out that two important parameters, namely the gas-liquid ratio and the viscosity, were omitted in their correlation. The viscosity was justifiably omitted since their data was in the highly turbulent flow region for both phases, and most wells fall in this category. The gas-liquid ratio was incorporated to some extent in the gas-density term. In 1954, Gilbert9 presented numerous pressure gradient curves obtained from field data for various flow rates and gas-liquid ratios for the determination of optimum flow strings. However, no method is presented for predicting pressure gradients except by comparison to these curves. Baxendell, et al,10 proposed a method based on Poettmann and Carpenter's procedure

By J. M. Lommel, B. Chalmers

The transfer of material from the solid to the liquid states can be accomplished in several ways. It occurs by the application of heat in the more familiar metallurgical operations of melting but it can also be accomplished by solution in a liquid, as can occur in systems using liquid metals for heat-transfer media. The kinetics of this reaction were studied to learn more of the separate steps in the process. In the case of a pure material at its melting temperature, Te,A,, thermal energy must be supplied to the solid in an amount equal to the latent heat of fusion in order for the solid-to-liquid transfer to occur. The rate at which heat is supplied, and hence the rate of melting, is a function of the temperature gradients in the system. This phase transfer can also occur in the absence of temperature gradients in the system illustrated in Fig. 1, which is a partial phase diagram between the components A and B. A solid of composition CI will

Jan 1, 1960

By Robert W. Thompson, Darry A. Ferguson

In August, 1977 the United States Congress passed Public Law 95-87 which has been commonly referred to as the Surface Mining Control and Reclamation Act (or SMCRA). This title is somewhat misleading in that the act creates as many regulatory requirements for underground coal mines as for surface coal mines. How- ever, this paper will concentrate on the effects of SMCRA on designs and stability for various activities of surface coal mines, specifically those concerning "Disposal of Excess Spoil". In the past, the objective of most laws and regulations applicable to the mining industry has been to achieve goals of safety or environmental concerns for all types of mining. However, SMCRA is unique in that it sought to regulate-all-activities of coal mining from initial data gathering, exploration, mine design and facilities design to reclamation activities and design. More specific to the stability of the activities of surface coal mining, special criteria for design and construction performance standards have been promulgated for the construction and maintenance of roads, dams and embankments, coal processing waste, ex- cess spoil piles, backfilled reclamation and pit slides. The criteria for design for the previously mentioned facilities has been enumerated by regulations and in many ways restrict the use of site specific design parameters. The restrictions imposed by regulations significantly inhibit the engineer's ability to develop the best practical and economical design and in some cases may re-

Jan 1, 1983

By E. Miller, K. L. Komarek, M. Ettenberg

The activity of aluminum in solid Co-A1 alloys has been measured by an isopiestic technique between 850° and 1200°C from 45 to 80 at. pct Al. The activity shows a Precipitous decrease around the stoichzornetric composition of CoAl. Free energies of mixing have been calculated over a limited composition range. Considering an antistructure-vacancy defect mechanism, the degree of intrinsic disorder, a , in CoAl was related to the alunminum activity. Excellent agreement between the calculated and experimental activity curves was obtained for a = 1.25 x 10-4. ThERMODYNAMIC properties of solid aluminum-transition metal alloy are being studied in an investigation of disordering in ordered compounds. In a continuing series of investigations, activities of solid Fe-1,' Ni-A1, kd r-A13 alloys have been measured. From the results for Fe-A1 and Ni-A1, the degree of intrinsic disorder for the equiatomic compounds was calculated2 using equations derived by Wagner and chottk. From the results for Cr-A1 the degree of intrinsic disorder was calculated from equations derived by Orr.' In this paper, the results of the study of Co-A1 alloys are described. Published activity data in the Co-A1 system has been limited to liquid alloys at 1600°C.° A heat capacity study7 of stoichiometric CoAl indicated that a second-order phase transformation occurs at 790° C, attributed to an order-disorder reaction. Oelsen and Middel,' employing the calorimetric mixing of pure liquid metals, obtained heats of formation for compositions from 6 to 90 at. pct Co. Heats of formation for 50 and 78 at. pct Co alloys have also been measured by acid solution calrimetr. The Co-A1 phase diagram, as compiled by Hansen and Anderko,lo is in good agreement with more recent X-ray evidence. The method for measuring activities of aluminum in this study is essentially that employed in the studies of the Fe-1,' i-Al, and r-A13 systems. This isopiestic method entails placing cobalt specimens, in a temperature gradient, in a sealed alumina system containing a pure liquid aluminum source of fixed vapor pressure. The specimens are equilibrated, cooled to room temperature, and their final compositions determined. From the measured temperature of the specimens and the known vapor pressure of pure aluminum the activities of aluminum in the alloy can be calculated. EXPERIMENTAL PROCEDURE The cobalt was 3-mil-thick sheet of 99.9 pct purity (herritt Gordon Mines Ltd., anada). The major impurities were 0.1 pct Ni, 0.014 pct C, 0.018 pct Fe, 0.004 pct S, and 0.005 pct Cu. The aluminum metal had a purity of 99.99 pct (Aluminum Corp. of America) and all alumina parts were 99.7 pct A1,O3 (Triangle RR Grade, Morganite Refractories, Inc.) with major impurities 0.05 pct SiOz, 0.1 pct Fe203, 0.2 pct NazO, and 0.05 pCt K20. Runs 1 to 3 were made with annular cobalt specimens (12 mm ID by 21 mm OD) punched from the sheet. The specimens were deburred and degreased in carbon tetrachloride and in acetone. The samples, each weighing about 150 mg, were then positioned along an alumina rod, a in. OD by 14 in. long, separated by alumina spacers, i in. ID by | in. OD by & in. long. The lower end of the rod was placed in a hole drilled in the center of an 80-g aluminum cylinder. This assembly was put into an alumina crucible, 1+ in. ID by 13 in. OD by 3+ in. high, and the position of each sample was measured to within 50.5 mm relative to the bottom of the crucible. An alumina tube, 28.5 mm ID by 35.5 mm OD by 14 in. long, closed at the top, was slipped over the whole assembly, so that it fitted snugly into the bottom crucible. The entire reaction assembly was tied with molybdenum wire and lowered into a mullite tube, closed at the bottom. A quartz thermocouple tube, closed at one end, containing a t/Pt-10 pct Rh thermocouple, calibrated according to the specifications of the National Bureau of standards,'' was placed along the reaction assembly inside the mullite tube. The temperature of each specimen could be determined by gradually raising the thermocouple and measuring the temperature gradient along the reaction assembly. The combined error in temperature measurement and sample position resulted in a total error of Q°C in the recorded temperature of each sample. The mullite tube was sealed at the top by a water-cooled brass head, connected to a conventional glass vacuum system. The aluminum reservoir is heated to its melting point sealing the alumina system containing the samples. During this process the pressure is maintained below 0.01 li Hg. During subsequent heating to establish the proper temperature gradient and throughout the entire run the pressure is maintained below 2 1 Hg by means of a two-stage mechanical pump. Equilibration runs lasted from 4 to 6 weeks and were terminated by air cooling. The temperature of the liquid aluminum reservoir was brought below its melting point in less than 20 min. For runs 4 and 5, alloy buttons with 49 and 69 at. pct A1 were prepared from the initial high-purity metals by arc melting under purified argon. The alloy buttons were comminuted to powder with an alumina mortar and pestle until the powder passed through a 400-mesh screen, particle size 0.0014 in. Portions of this powder weighing between 50 and 200 mg were placed in small alumina trays, 25 by 15 by 5 mm, which were then

Jan 1, 1969

Edwin H. MessiteR, New Pork City (communication to the Secretary*):—Under the heading " Flues," Mr. Edwards refers to the Bee-hive construction, a cross-section of which is shown in Fig. 4 of his paper. A flue similar to this was designed by me about six years ago,' in which the walls though much thinner than those described by Mr. Edwards gave entire satisfaction. These walls, from 2.25 in. thick throughout in the smaller flues, to 3.25 in. in the larger, were built by plastering the cement mortar on expanded-metal lath without the use of any forms, or cribs, whatever, at a cost of labor generally less then $1 per sq. yd. of wall. Of course, where plasterers cannot be obtained on reasonable terms, the cement can be molded between wooden forms, though it is difficult to see how it can be done with an interior core only as stated by Mr. Edwards. In regard to the effect of sulphur dioxide and furnace-gases on the cement, I have found that, in certain cases, this is a matter which must be given very careful attention. Where there is sufficient heat to prevent the existence of condensed moisture inside of the flue, there is apparently no action whatever on the cement, but if the concrete is wet, it is rapidly affected by these gases. At points near the furnaces there is generally sufficient heat not only to prevent internal condensation of the aqueous vapor always present in the gases, but also to evaporate water from rain or snow falling on the outside of the flue. Further along, a point is reached where rain-water will percolate through minute cracks caused by expansion and contraction, and reach the interior, even though internal condensation does not occur there in dry weather. From this point to the end of the flue the roof must be coated on the outside with asphalt paint or other impervious material. In very long flues a point may be reached where moisture will condense on the inside of the malls in cold weather. From this point to

Jan 1, 1905

By R. G. Mallon, R. L. Braun

Primary copper-sulfide ore deposits that are well below the water table can be chemically mined by in-situ high-pressure leaching. The leaching is accomplished by pumping oxygen gas into the bottom of a large underground flooded column of rubblized ore. Part of the injected oxygen dissolves under the high hydrostatic pressure in the column. With a high enough injection rate, the excess oxygen gas induces a convective circulation of oxygenated solution within the rubble column, which transports dissolved oxygen throughout the system. At elevated temperatures, this results in a relatively rapid dissolution of the copper minerals. A method of calculating the leaching rates is presented. The calculation is done by means of a finite-difference computer code that couples all of the processes relating to copper leaching, convective circulation, and the injection, dissolution, and consumption of oxygen. Results of the calculation for a typical case show that over 70% of the copper can be extracted in less than six years with good efficiency in oxygen utilization.

Jan 1, 1976

By W. A. Bates, R. J. Miller

Although cresylic acids have been standard frothers in flotation for many years, there has been little discussion of their nature in the metallurgical literature. Aside from references in the patent literature, the paper by Landolt, Hill, and Lowyl in 1930, which resented a study of the frothing and collecting properties of some of the constituents of crude cresylic acids, represents the only contribution of this type. The close froth control required in the delicate selective separations of present-day flotation operations have required the flotation metallurgist to choose his frothers with care, and have caused him to require of the manufacturer a closely controlled, uniform product. A background of knowledge of the chemical composition and physical and chemical properties of the frothers, by which their action may be correlated, should aid in selecting frothers for particular flotation requirements. Further, the recent almost complete replacement in flotation of coal-tar cresylic acids by those derived from petroleum makes it especially desirable to review the flotation behavior of the acids from the old and the new sources. In view of these facts the Milling Methods Committee of the A.I.M.E. suggested to the Oronite Chemical Co. of San Francisco the preparation of a paper on the subject, and this paper has accordingly been prepared as a contribution by the California Research Corporation, the research affiliate of the Oronite Chemical Co. The discussion is from the following aspects: (I) constitution and properties; (2) sources; (3) comparison of coal-tar and petroleum cresylic acids; (4) characteristics as frothers, with particular reference to the effect of the substitution of petroleum acids for coal-tar acids. Constitution and Properties Cresylic acids are commonly regarded as mixtures of orthocresol, metacresol and paracresol. This was, indeed, the former meaning of the term, but in recent years it has been loosely applied to any mixture of alkyl phenols boiling above 190°C.; that is, excluding only phenol itself. This means that cresylic acids, as they are known today, may consist of mixtures, not only of the three isomeric cresols, but of six xylenols and of a variety of higher boiling homologues. Generically the constituents of cresylic acids are alkyl phenols, and they are often so designated in the literature to avoid the more indefinite term, "cresylic acids." They form an homologous series starting with phenol, which has the familiar benzene ring, with an hydroxyl group in place of one of the hydrogen atoms. The series of alkyl phenols is formed by the substitution of alkyl side chains, such as methyl, ethyl, propyl, butyl, etc., for hydrogen atoms of the benzene ring of phenol. Some

Jan 1, 1947