Search Documents

By J. A. Solomon, H. E. Shafer

As a result of the great demand for metallic aluminum and the scarcity of domestic bauxite, numerous processes have been proposed and developed to extract the oxide of this metal (Al2o3) from clays, shales, and other low-grade raw materials.1-4 An exploratory study was made to extract alumina with sulfuric acid from relatively impure coal-associated draw-slate and to establish an optimum calcination temperature for maximum recovery. Draw-slate is the term used to describe the hard, slaty material directly overlying many coal seams and may range from a few inches to a few feet in thickness. Alumina content of these draw-slates may range from as low as 15% to over 35%. Although the following results are limited in scope, some of the data should prove beneficial for further work. Coal-associated clay, shale, and gob heretofore have been considered nuisance products; any successful alumina extraction process would greatly enhance the worth of these almost limitless resources. This research demonstrated that an optimum calcination temperature for alumina extraction could be established for a coal-associated draw-slate and that this temperature was lower than those suggested in previous work with unspecified clay types. It should be noted that slightly higher acid concentrations and somewhat finer particle sizes were used in this series of tests as compared to previous work. EXPERIMENTAL WORK Essentially, alumina extraction proceeded in four steps: 1) grinding, 2) calcining, 3) acid leaching, and 4) precipitating of aluminum sulfate. An initial series of reference tests to determine the optimum temperature of solubility for alumina was run using relatively pure kaolin. Kaolin forming clays are hydrous aluminum silicates of the approximate composition 2H2O A12O3 2SiO and kaolinite is the mineral that predominates in most kaolins. 5 The kaolin was ground to -30 mesh and subsequently calcined at temperatures ranging from 100°C to 700°C. Each sample was calcined for 1 hr in a muffle furnace and in turn subjected to sulfuric-acid leaching (H2SO4, 9 molar) for a 2-hr period. The filtrates were analyzed for the amount of dissolved alumina recovered.637 Also, each sample of leached or barren residue was

Jan 1, 1968

By W. N. Tanner

THE wire-rope hoisting conditions at the mines of the Anaconda Copper Mining Co. in Butte, Mont., are very severe because of the conditions under which it is necessary to operate. A study was made, in the fall of 1919, for the purpose of changing these conditions in order to obtain longer rope and sheave life. There are at present in Butte, hoisting engines equipped with wire rope as follows: 9 main hoists using flat ropes. 7 main hoists using 1 ½ in. rope. 5 main hoists using 1 ¼ in. rope. 6 shafts using 1 1/8 in. rope. 2 chippy hoists using 1 ¼ in. rope. 9 chippy hoists using 1 1/8 in. rope. 15 shafts using 1 in. rope. 7 shafts using 7/8 in. rope. 1 shaft using ¾ in. rope. In addition, there are a number of sinking engines using 5/8 in., ¾ in., 7/8 in., and 1 in. (15.9, 19, 22, and 25 mm. rope.) The flat ropes run from ½ by 7 ½ in. (12.7 by 190.5 mm.) to ½ by 4 ½ in. (9.5 by 114 mm.) and are used on the older hoisting-engines, which are set comparatively close to the shaft. Because of swelling and moving ground at some of the shafts, these ropes present certain difficulties in operation that are more pronounced than with round ropes; they are, therefore, being superseded by round ropes as newer engines are being installed. They are, however, much more easily inspected and repaired than round ropes.

Jan 2, 1922

By J. W. Pugh, Sam Leber

Single crystals of tungsten were made and deformed in tension at 3000°C. The slip traces so formed on these crystals were analysed to determine the apparent slip system. Results indicate that deformation occurs in the<III> direction on planes of maximum shear stress. This determination agrees with the early work of Taylor and Elam on other body-centered cubic crystals at lout temperatures. SLIP in face-centered cubic and hexagonal close-packed metals has consistently manifested itself in straight traces which indicate that glide takes place on planes of highest atomic density and in directions of closest packing. The slip traces observed on body-centered cubic metals are, on the other hand, frequently branched and wavy, and indicate that while glide takes place in the direction of closest packing, it does not necessarily choose the plane of highest density. The early work of Taylor and Elam1 4 indicated that glide took place in the close-packed direction on planes close to those defined by the maximum shear stress. Subsequent investigations have tried to rationalize these observations in terms of an elementary process on the close-packed planes (110). For example, Elam5 and Grenin~er&apos; have suggested alternate glide on nonparallel (110) planes with the observed result that the summation of these glides results in a trace which defines some plane other than{110). Madden and chen7 have recently reviewed the phenomenological and theoretical aspects of noncrystallographic slip. More recently Koehler&apos; has presented a model of dislocation propagation which permits another rationalization. He indicated that dislocation loops are transferred from one glide plane to another by double cross-slip of screw segments. It is reasonable to assume that, on the average, such transfers may result in a trace which approaches the plane of maximum shear stress. The work described in this paper will show that

Jan 1, 1961

By C. Laird, C. E. Feltner

May different kinds of dislocation structures have been observed in strain-cycled metals and alloys. In order to understand their pattern and causes, an experimental program has been carried out to determine the influence on the dislocation structures of the three variables: 1) slip character of the material, 2) test temperature, and 3) strain amplitude. The results show that at high strain amplitudes cell structures me formed when the slip character is wavy, and that these are progressively replaced by uniform distributions of dislocations as the stacking fault energy is decreased. At lower strains, dislocation debris is formed which consists primarily of dipoles in wavy slip mode materials and multipoles in planar slip mode materials. Temperature merely acts to change the scale of the structure, smaller cells, and clumps of dislocation debris being associated with lower temperatures. It is shown that the results for many metals fit this pattern, which Parallels that occurring in unidirectional deformation. DISLOCATION structures produced by cyclic strain (fatigue) have been examined in a number of metals by transmission electron microscopy. These studies have produced a variety of interesting and often seemingly conflicting results. For example, different investigators have reported such structural features as cells.le4 bands of tangled dislocations,4&apos;5 dense patches or clusters of prismatic dislocation loops, planar arrays,4&apos;10 and various combinations or mixtures of these different structures. Most of these observations have been made on materials which were initially annealed and cyclically strained at low amplitudes resulting in long lives. Recently we have reported observations of the dislocation structures produced in copper and Cu-7.5 pct Al cycled at large amplitudes, resulting in lives of less than 104 cycles.4 These results, examined in combination with those in the literature, have suggested that a common or consistent structural pattern exists. Variations in this pattern appear to be determined chiefly by the three variables, namely, the slip character of the material,4,11 test temperature. and the strain amplitude. To verify this interpretation, we have studied [he influence of the above three variables (in different combinations) on the resultant structures in cyclically strained metals. Copper, fatigued at room temperature, was chosen as a reference state to which all other observations can be compared. The effect of slip character has been investigated by employing fcc metals of different stacking fault energy. Thus aluminum which has a more wavy slip character than copper, and Cu-2.5 pct A1 having a more planar slip char- acter, have been examined. The aluminum samples were fatigued at 210°K thus making their homologous temperature equal to that of copper at room temperature. The influence of temperature has been evaluated by examining the structures in copper at room temperature and 78°K. Finally the effect of strain amplitude was studied by looking at the structures at amplitudes giving lives ranging from 104 to 107 cycles. All of the specimens were examined at the 50 pct life level at which stage the structures have reached a stable configuration.12 I) EXPERIMENTAL PROCEDURE Strip specimens, 0.006 in. in thickness, were prepared from base elements of 99.99 pct purity or greater. Specimens were fatigued by cementing the strips to a lucite substrate which was subjected to reverse plane bending. This method of testing has been described e1sewhere.7 After fatiguing, specimens were thinned and examined in a Philips EM 200 which was equipped with a goniometer stage capable of ±30-deg tilt and 330-deg rotation of the specimen. On the basis of separate calibrations,13 allowances were made for the relative rotation and inversions between the bright-field images and the diffraction patterns. II) RESULTS AND DISCUSSION The life behavior of the materials under different test conditions is shown in Fig. 1 in the form of plots of total strain range vs cycles to failure. Comparisons of structures produced in the different materials were made at amplitudes which produced equal numbers of cycles to failure. The influence of strain amplitude on the structures produced in the reference state material (copper tested at room temperature) is shown in Fig. 2. At the 104 life level the structure produced comprises cells similar to those previously observed.3,4 They are approximately 0.5 p in diam and the cell walls are generally more regular or sharper than those produced by unidirectional deformation.14 At the 10&apos; life level the

Jan 1, 1969

By Warren E. Holland, Leon H. Robinson

The pore pressure must be included in any discussion of the state of stress within a rock. Rock cylinders at elevated stress levels, loaded uniaxially to a stress less than the yield strength, can be fractured by holding the constraints constant and increasing the pore fluid pressure. This can be described in terms of the Mohr envelopes using effective stresses. The effective stress concept can simplify data with various confining and pore pressures. When the pore and confining pressures are equal, the pore pressure appears to be totally effective in reducing the confining pressure effects. The area over which the pore pressure acts has been the subject of some prior discussions. Terzaghi 1 defined boundary porosity as ". . . the ratio of that part of the area of the potential surface which is in contact with the interstitial liquid and the total area of this surface." His method of calculation included a discussion of splitting failure which was objected to by Mr. Kessler, National Bureau of Standards. The values calculated by Terzaghi were close to unity. Leliavsky,2 using unjacketed cement cores, reported that the interstitial fluid pressure appeared to act upon about 92% of the surface of failure. He concluded: "The fraction of the area of cross-section over which the internal pressure acts can therefore have nothing to do with ordinary porosity, and the results of the experiments tend to support Professor Terzaghi&apos;s views." In 1947 Balmer3 determined the boundary porosity of concrete when the confining and pore pressures were equal. He also found values close to unity. In 1948 McHenry4 published some of the results from the same equipment and included the first data in which the pore pressure

Jan 1, 1970

By H. B. Fuqua, B. E. Thompson

The area discussed herein, commonly known as the North Texas district, embraces the following 10 counties: Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita and Wilbarger. It is underlain by two major structural features. The northernmost portion of the district, including Cooke, Montague, northern Clay, Wichita, Wilbarger, Foard and Hardeman counties, is underlain by the system of buried mountains known as the Red River uplift, which is parallel to and closely related to the Wichita-Amarillo uplift of Oklahoma and the Texas Panhandle. While the presence of a great majority of the numerous oil fields of the area is traceable to this feature, the production in Archer, southwestern Clay and southeastern Baylor counties is due to the influence of what is known as the Cisco Arch (so called because of its influence on Cisco deposition), the axis of which extends in a north\lest-southeast direction across Archer County. Discussion of Tables Preliminary to discussing developments during the year 1933, it appears advisable to offer a few words of explanation on Tables 1 and 2, included as part of this paper, in which an effort has been made to sumlllarize oil and gas development in North Texas to Jan. 1, 1934. One of the chief objectives of this publication is understood to be to show production by individual pools, and, if possible, by distinct pays in a pool. This the authors haw been unable to do for North Texas. It is a generally recognized fact that there are well over 100 individual pools, which should perhaps be mow properly called "productive spots," in Archer county alone, with perhaps an even greater number in Wichita County. It can be found upon investigation that an apparently continuous productive area covering Many acres consists of a half dozen lenticular sands, all stratigraphically different,, which produce only under portions of the apparently continuous area. It is also a fact that practically all gross production records are carried by the various intcrcsted parties by major districts or by counties. It is obvious therefore

Jan 1, 1934

By J. W. Downey, A. E. Dwight, R. A. Conner

THE MgCu2 type Laves phase has been observed in the thorium-osmium and thorium-iridium systems. Two alloys corresponding to ThOs2 and ThIr, were prepared by arc melting a 5-g charge in a water-cooled copper. crucible. Both alloys were very brittle. X-ray diffraction patterns were obtained using filtered Cu and Co radiation with a Straumanis-type DeBye-Scherrer camera. The a,, values as shown in Table I were obtained by a Nelson-Riley extrapolation. The structure belongs to space group Oh7-Fd3m. Relative intensities for each of these compounds were calculated on the assumption that 8 thorium atoms occupy (a) positions and 16 osmium or irid-ium atoms occupy (d) positions. The calculated intensities are the product of the Lorentz-polarization factor, the multiplicity factor and F&apos;, the structure factor, neglecting the absorption and temperature

Jan 1, 1959

By C. E. Shoenfelt

The year 1939 witnessed the rapid development of several of the more important Rocky Mountain oil and gas areas and the discovery of new oil and gas fields. As a further result of an active year, many oil fields had their productive limits greatly extended or responded to deeper drilling with oil production in lower horizons. In Colorado there was a substantial increase in refinery capacity, with three new units constructed. Its contribution to the crude-oil supply was an important extension of the producing area of a Western Slope field and a deeper oil-producing horizon in an old field east of the Front Range. Occurrences of gas were reported in two wells in northwestern Colorado, but severe winter weather prevented tests and the value of these discoveries cannot be determined at this time. Montana&apos;s northern fields were extended and a number of record wells were completed. The North Cut Bank area gives promise of wide expansion in 1940. The gas-producing area of Wyoming&apos;s Elk Basin field was extended into Montana on the north plunge of the anticline. The most important developments in Wyoming oil fields in 1939 were extensions to the producing area of Lance Creek and the discovery of a deeper pay in the Tensleep formation at Wertz dome. A new gas field at Horn Valley in the south central part of the state was the only new field discovered, but wildcatting was at low ebb in Wyoming in 1939. Colorado In Colorado, the year 1939 saw the completion of several interesting tests, but largely with negative results. Oil was discovered, however, in a deeper sand in the old Fort Collins field and the productive area of the Wilson Creek field was extended. Gas had been noted in two Western Slope wells, at Yellowjacket-Buford and at Trull, but their volumes had not been determined at the end of the year. Of principal interest, however, were the failures, descriptions of which will be given presently. One of these established a new depth record for Colorado.

Jan 1, 1940

By C. E. Shoenfelt

The year 1939 witnessed the rapid development of several of the more important Rocky Mountain oil and gas areas and the discovery of new oil and gas fields. As a further result of an active year, many oil fields had their productive limits greatly extended or responded to deeper drilling with oil production in lower horizons. In Colorado there was a substantial increase in refinery capacity, with three new units constructed. Its contribution to the crude-oil supply was an important extension of the producing area of a Western Slope field and a deeper oil-producing horizon in an old field east of the Front Range. Occurrences of gas were reported in two wells in northwestern Colorado, but severe winter weather prevented tests and the value of these discoveries cannot be determined at this time. Montana&apos;s northern fields were extended and a number of record wells were completed. The North Cut Bank area gives promise of wide expansion in 1940. The gas-producing area of Wyoming&apos;s Elk Basin field was extended into Montana on the north plunge of the anticline. The most important developments in Wyoming oil fields in 1939 were extensions to the producing area of Lance Creek and the discovery of a deeper pay in the Tensleep formation at Wertz dome. A new gas field at Horn Valley in the south central part of the state was the only new field discovered, but wildcatting was at low ebb in Wyoming in 1939. Colorado In Colorado, the year 1939 saw the completion of several interesting tests, but largely with negative results. Oil was discovered, however, in a deeper sand in the old Fort Collins field and the productive area of the Wilson Creek field was extended. Gas had been noted in two Western Slope wells, at Yellowjacket-Buford and at Trull, but their volumes had not been determined at the end of the year. Of principal interest, however, were the failures, descriptions of which will be given presently. One of these established a new depth record for Colorado.

Jan 1, 1940

By W. L. Finlay

Size effects in quenching steel are particularly prominent and well recognized because of the existence of a critical cooling rate separating nuclea-tion and growth transformations, as exemplified by the formation of pearl-ite, from the shear type of transformation characterizing the martensite reaction. The absence of a similar, sharply demarcating cooling rate is characteristic of precipitation hardening systems and size effects in these are correspondingly less prominent. This paper is concerned with a size effect in high-purity, precipitation-hardenable alloys which appears not to have been recognized previously. This effect is believed to result from the thermal fluctuations which inevitably occur in quenching a specimen of finite size into a cooling liquid rather than from the existence of a critical cooling rate. QUENCHING "ANOMALIES" The precipitation hardening literature contains many references to so-called anomalous quenching and aging results. By "anomalous", investigators usually meant that their alloys did not consistently harden on aging after quenching according to some anticipated pnttern: not infrequently virtually no age hardening occurred with compositions known to be precipitation-hardenable. Perhaps the most prominent series of anomalies was reported over a 15-year period by Gayler and coworkers on aluminum-copper.l,2,3,4 Working with silver-rich copper alloy, Cohen5 secured some very interesting Rockwell F hardness changes of from 1-5 Rockwell points between the first peak and valley. Fink and Smith borrowed one of Cohen&apos;s specimens and, following his heat treatment and quenching practice to the letter, secured6 very different results in which only one peak was obtained and in which the hardness level at the aging lime of Cohen&apos;s first peak was 20 Rockwell F points higher. Fink and Van Horn7 encountered serious deviations in age-hardening high purity aluminum-zinc alloys. They stated that "the discrepancies were larger than might be expected from possible experimental errors in the Brinell readings." Geisler, Barrett and Mehl8 likewise encountered anomalous hardening results in aluminum-silver alloys, securing quite different age-hardening curves from two identical specimens. They stated that "the treatments of these samples had been the same, so that the different behaviors could be attributed only to accidental variations in the quenching practice."

Jan 1, 1950

By J. D. Sullivan, Chester R. Austin, J. L. Nunes

IT is characteristic of most shales and surface clays that a bloated or vesicular structure is produced by burning to a sufficiently high temperature, usually about 150° to 200°F. above the normal maturing temperature used when making common brick of the same material. Early investigators recognized this phenomenon and attributed it to the release or expansion of gases in the vitrified piece. A number of theories have been advanced on the source of the gas and the manner in which it is evolved, but none has been proved conclusively. T. E. Jackson&apos;s1 early theory that bloating was due to oxygen evolved by ferric oxide in forming ferrous oxide or ferrous silicate was never substantiated by experimental work. Orton2 thought this explanation unlikely, as all clays should bloat at the same temperature, if this were true. He found that clays bloated in the range from 1100° to I700°C. Also, many clays containing iron did not bloat at all, but fused. Orton also stated that oxidation of different types of carbon was a source of gas during burning of clay and should be expelled before vitrification was reached. Seger3 said that he had dissolved ferric oxide in glass with no apparent evolution of gas. Matson4 came to the conclusion that ferruginous clays burned to vitrification in an oxidizing atmosphere did not have the iron in a ferrous form. According to Wilson,5 the gases responsible for bloating might be entrapped air, water, sulphur dioxide, carbon monoxide, oxygen, and hydrocarbons. He spoke of two causes of bloating: (I) incomplete oxidation below the vitrification temperature, and (2) decomposition of compounds and evolution of gases above the vitrification temperature. Decomposition of calcium sulphate was given as the principal example of the latter. Bleininger and Montgomery6 stated that if any time after vitrification began the evolution of gaseous matter was rapid enough so that pressure was produced within the clay, bloating was certain to take place, and a vesicular structure would be formed. They recognized that initial structure, rate of heating, kiln atmosphere, and many other variables affected bloating. Work done by the Emergency Fleet Corporation7 indicated that clays suitable for bloating should be high in compounds of metallic oxides, carbon, sulphur, sodium, potassium, or other equivalent compounds, which either act as a flux or give off gas. Orton2 studied the chemical status of the carbon, iron, and sulphur in clays during various stages of burning, using a Huron shale that bloated under oxidizing or reducing conditions. He found that only a small amount of sulphur remained in the clay and that it could be detected only by dissolving the clay in hydrofluoric acid,i.e., the sulphur was in combination with the silica. Orton said that this sulphur was probably in the form of iron sulphide dissolved in the glass phase. The iron sulphide was not broken down by heating, but was dissolved in the basic slag or glass,

Jan 1, 1942

By M. J. Marcinkowski, E. N. Hopkins

An investigation has been made of the ß(fcc) — a(hexagonal) transformation which occurs in lanthanum using both electrical resistivity and transmission electron microscopy techniques. It has been shown that the ß phase can be retained below the transformation temperature by rapid quenching but that the sample immediately begins to transform to the a phase. The transformation is observed to nucleate in the vicinity of inclusions. Based on the above observations, a detailed model of the transformation has been advanced which involves the nucleation of an extrinsic stacking fault bounded by a pair of Shockley partial dislocations in the vicinity of some heterogeneity, i.e., an inclusion. The stress field of the resultant dislocation pair acts to nucleate extrinsic faults in adjacent planes and leads quite naturally to the B-a conversion with a minimum of strain energy induced in the crystal. LANTHANUM possesses an fcc structure ß) (8) upon cooling transforms to a hexagonal modification (a) in much the same way as cobalt. The one exception, however, is that the stacking sequence of the closest packed planes in a La is ABAC ABAC, and so forth,1 whereas in cobalt it is ABAB, and so forth, i.e., hep. Mainly on the basis of transmission electron microscopy techniques, there seems to be little doubt that the 0 — a transformation in cobalt involves a dislocation mechanism2 although its exact nature still remains obscure. Although the ß - a transformation in lanthanum is somewhat more complex than that occurring in cobalt, it was thought that its very uniqueness would be helpful in understanding fcc — hexagonal transformations in general. Such a general understanding of these transformations is important since they represent what are perhaps the simplest of the martensitic class of transformations. The experimental techniques used were those of electrical resistivity and transmission electron microscopy. EXPERIMENTAL PROCEDURE The lanthanum used in this investigation was prepared by the calcium reduction of lanthanum fluoride in a tantalum crucible under an argon atmosphere as described by Spedding et al. The residual calcium was removed by vacuum remelting in a tantalum container. Portions of the metal were then analyzed by emission spectroscopy as well as vacuum fusion. The amounts of the various impurities that were found are listed in Table I. A portion of the lanthanum ingot was swaged at room temperature into 0.030-in.-diam rod for the resistivity samples while the remainder was rolled into 0.010-in.-thick sheet for the transmission electron microscopy phase of this investigation. In order to eliminate the plastic deformation induced in the samples during fabrication, they were sealed in evacuated tantalum lined quartz capsules and annealed for 1 hr at 700° C. Specimen resistances were measured using the conventional "four-wire" technique described by MacDonald, 4 employing a type K-3 Universal Potentiometer and a standard 0.001-ohm resistor, both manufactured by Leeds and Northrup Co. By taking into account all of the possible errors in the apparatus, it was felt that the absolute resistivities of the approximately 0.87-in.-long specimens measured are reliable to 3 pct. Resistances from room temperature to 700°C were measured using a vacuum furnace. In order to avoid sample contamination by the thermocouple, chromel-alumel leads were spot-welded into a tantalum shield which in turn was welded to the lanthanum specimen. Resistances below room temperature were obtained by transferring the sample to a helium gas-filled quench tube and slowly dripping liquid nitrogen into a surrounding dewar flask. A steady reduction of temperature to about —190°C was completed in about 23 hr, and the resistances were measured at various temperature intervals. As will be shown shortly, rapid quenching from above about 350°C was sufficient to suppress the B -a transformation initially but subsequent annealing at lower temperatures leads to a partial ß --a conversion. To investigate this aspect of the transformation, the samples were suspended in the hot zone of a helium-filled furnace from which they could be rapidly dropped into the quench tube mentioned previously which was now

Jan 1, 1969

By C. Norman Bowers, Blaine B. Wescott

Marked improvement in the serviceability of sucker rods has been effected in the last two years, partly because of the insistent necessity for greater economy in the operating costs of crude oil production growing out of the general industrial depression and partly because many of the recently developed fields have imposed more severe operating conditions upon both surface and underground equipment. The latter is particularly true of Kansas, where practically all of the oil produced is associated with damaging amounts of hydrogen sulfide brine and where the method of establishing potential production demands equipment capable of being operated at maximum capacity without interruptions. The decline of flush production in the Oklahoma City field created new problems in deep-well pumping on a scale heretofore unequaled and the increased proportion of water it has been necessary to produce in the fields of the Greater Seminole area presented conditions that were acutely in need of betterment. The problem in the latter fields was complicated by the shift towards sulfide characteristics, which accompanied water encroachment, and it is probably true that nowhere, at the present time, are pumping conditions generally as severe as in this territory. The Mid-Continent district, therefore, has become the proving ground for the numerous materials that have been proposed for sucker-rod fabrication. The information that ultimately will be obtained from an unprecedented amount of field experimentation will pay ample dividends when the decline of East Texas increases the demand for the vast reserves of sour crude in West Texas. It is a rare occurrence in industry that the use of such a simple piece of equipment as a sucker rod presents so complicated a problem for solution. As proof of this, it is only necessary to consider the numerous types of sucker rods on the market at the present time and contrast this condition with that of less than four years ago, when it was the common aim of manufacturers to develop a single sucker rod for all conditions of

Jan 1, 1935

By E. T. Dumble

For many years there have been occasional reports of the discovery of gold from a belt of the coast country of Texas which is underlain by deposits belonging to the lower Eocene. For the most part they have been treated as newspaper reports and no examination or record of them has been made. Among such, it may be mentioned that in 1896 there was a flurry over reported gold-discoveries west of Luling and elsewhere in this belt, and in 1903 some prospect-shafts were sunk on the Gon-zales branch of the Galveston, Houston & San Antonio railway, 3 miles below Harwood. During 1912, further discoveries have again brought the matter to our attention, and it may be of interest to record the facts as we have found them. Some years ago specimens were sent me, which were said to have been taken from certain beds on Gazley creek, and concentrated by washing in a rocker. In them were several particles of gold sufficiently large to be visible to the eye. Under the microscope they showed to be, with few exceptions, sharp cornered, and not rounded as is usual with placer-gold. They were not filings, however, but their sharpness seemed rather to be due to a recent freeing from their matrix. One or two grains were rusty, and one copper-hued, but the most of them were tolerably bright. On examining the material of the samples small grains or fragments were found, of a yellowish brown color, which seemed to be of a finely-granular structure—possibly a sandstone. In these fragments I found particles of gold, one of them being large enough to be visible without a lens. Gazley creek empties into the Colorado river just north of Smithville, and for a few miles north of that place its banks show, beneath the deposits of more recent materials, the sands and clays of the Lignitie division of the Eocene, with lignite, shells of iron, etc.

Jan 1, 1913

By Theron Wasson

The year 1942 in Michigan was devoted largely to the development of fields discovered in 1941 but was also characterized by a great increase in prospecting for new productive horizons below the Dundee limestone. Some new fields were discovered but as yet these have shown few signs of being of major importance. Michigan&apos;s total production for 1942, of 21,754,000 bbl. of oil, as reported by the U. S. Bureau of Mines, was second only to the record year of 1939 when 22,799,000 bbl. of oil were produced. All important fields were prorated throughout the year, and it is obvious that without proration a new all-time high would have been established for the state this year. From 1925 to the end of 1942, Michigan has produced annually the following amounts of oil: Year Barrels Source 1925 4,000 1926 94,000 1927 435,000 1928 592,000 1929 4,641,000 1929 Michigan Geological Survey 1930 3,928,000 3,785,000 1932 6,925,000 1933 7,942,000 1934 0,603,000 1935 15,776,000 U.S. Bur. Mines, 1937 1936 11,928,000 U.S. Bur. Mines, 1938 1937 16,628,000 U.S. Bur. Mines, 1939 1938 19,211,000 U.S. Bur. Mines, 1938 1939 22,799,000 1940 19,764,000 1941 16,361,000 1942 21,754,000 Total 183,170,000 This tabulation shows the steady growth of the industry in Michigan since the first discovery of oil in 1925. Maes A map of the oil and gas fields of Michigan in 1941, published in the report for 1942, shows the main producing areas and should be referred to if information in regard to their location is desired.* The main producing zones were shown in the columnar section in the same publication. Development in Fields Reed City Field.—During 1942 the Reed City field, which ended 1941 with 112 producing oil wells, added 70 new producers to bring the total at the end of the year to 182 wells and 4700 proven acres. A south extension of the field developed during the year was in large part responsible for the increase. Approximately 9,000,000 bbl. of oil was produced from the field during the year, bringing the total accumulated production to the end of the year to roughly 11,750,000 barrels. Headquarters Field.—The Headquarters field, which started the year with ro producing oil wells, ended the year with 41 wells aid 1240 proven acres. Approximately 2,300,000 bbl. of oil was produced in 1942. Kawkawlin Field.—Although not a 1941 discovery, the Kawkawlin field has been actively developed on the 40-acre spacing plan during the last year, 42 producers having been completed, bringing the total number of wells at the end of the year to 77. Nearly 500,000 bbl. of oil was produced during the year.

Jan 1, 1943

By Theron Wasson

The year 1942 in Michigan was devoted largely to the development of fields discovered in 1941 but was also characterized by a great increase in prospecting for new productive horizons below the Dundee limestone. Some new fields were discovered but as yet these have shown few signs of being of major importance. Michigan&apos;s total production for 1942, of 21,754,000 bbl. of oil, as reported by the U. S. Bureau of Mines, was second only to the record year of 1939 when 22,799,000 bbl. of oil were produced. All important fields were prorated throughout the year, and it is obvious that without proration a new all-time high would have been established for the state this year. From 1925 to the end of 1942, Michigan has produced annually the following amounts of oil: Year Barrels Source 1925 4,000 1926 94,000 1927 435,000 1928 592,000 1929 4,641,000 1929 Michigan Geological Survey 1930 3,928,000 3,785,000 1932 6,925,000 1933 7,942,000 1934 0,603,000 1935 15,776,000 U.S. Bur. Mines, 1937 1936 11,928,000 U.S. Bur. Mines, 1938 1937 16,628,000 U.S. Bur. Mines, 1939 1938 19,211,000 U.S. Bur. Mines, 1938 1939 22,799,000 1940 19,764,000 1941 16,361,000 1942 21,754,000 Total 183,170,000 This tabulation shows the steady growth of the industry in Michigan since the first discovery of oil in 1925. Maes A map of the oil and gas fields of Michigan in 1941, published in the report for 1942, shows the main producing areas and should be referred to if information in regard to their location is desired.* The main producing zones were shown in the columnar section in the same publication. Development in Fields Reed City Field.—During 1942 the Reed City field, which ended 1941 with 112 producing oil wells, added 70 new producers to bring the total at the end of the year to 182 wells and 4700 proven acres. A south extension of the field developed during the year was in large part responsible for the increase. Approximately 9,000,000 bbl. of oil was produced from the field during the year, bringing the total accumulated production to the end of the year to roughly 11,750,000 barrels. Headquarters Field.—The Headquarters field, which started the year with ro producing oil wells, ended the year with 41 wells aid 1240 proven acres. Approximately 2,300,000 bbl. of oil was produced in 1942. Kawkawlin Field.—Although not a 1941 discovery, the Kawkawlin field has been actively developed on the 40-acre spacing plan during the last year, 42 producers having been completed, bringing the total number of wells at the end of the year to 77. Nearly 500,000 bbl. of oil was produced during the year.

Jan 1, 1943

By H. W. Camp

The past year has had no revolutionary change in the process of petroleum refining, although there have been improvements and developments in practically every phase of operation, due largely, perhaps, to economic pressure. A few years ago, a Mid-Continent skimming plant using 35 gravity crude obtained 28 per cent. gasoline and naphtha; 9 per cent. kerosene, and the remaining yield gave gas oil and fuel oil. Figuring manufacturing cost, but not including sales, transportation, overhead and depreciation, the realization was $1.45 per bbl. of crude. Today, a thoroughly modern and up-to-date skimming plant, having all latest equipment, shows a realization of $1.74 per bbl. on the same basis. Thus it is evident that progressive developments have taken place in the last 2 or 3 years when potential earnings have been increased about 20 per cent. The average refiner is compelled to exert his utmost ingenuity in order to operate with a profitable margin. He has two factors to consider—recovery of maximum yields of profitable oils and the reduction of operating expenses. For the past 8 years, the margin between price of gasoline and cost of crude has grown narrower, constantly. Both these prices are determined by external conditions and not by the refiner himself, but the refiner might have been able to increase that margin had he more carefully controlled his output, limiting his production of light oils to current consumption. Be that as it may, this same economic pressure has given impetus to progress in improvements of primary distillation equipment, including stills, towers and heat-saving devices. A pipe still and bubble cap fractionating equipment can now replace a battery of shell stills, giving better yields, better control, elimination of rerunning and lowering of operating costs. The most recent pipe stills are being equipped either with radiant-heat furnaces or air-preheating systems and improved heat exchange equipment. These can be operated on a fuel consumption as low as 1 per cent. of the charge as compared to a fuel consumption of

Jan 1, 1929

By C. E Shoenfelt, Gail F. Moulton

Proven and developed oil reserves, and productive capacity increased during 1943 in the fieids of the Rocky Mountain region. Oil production during the year was nearly 45 million barrels, or slightly less than in 1942. The rate of production at the start of 1944 was slightly less than at the start of 1943. Pipe-line projects scheduled for completion during 1944 should permit a substantial increase in the rate of production. Wildcat exploration was more extensive in Montana during 1943 than in other states in the region. The results of wildcat drilling were unsatisfactory, although new oil fields were discovered on the Gebo, Little Buffalo Basin and Steamboat Butte structures of Wyoming, the Gage anticline of Montana, and the Clark Lake structure of Colorado. The area of the structures on which the discovery wells were drilled is known to be considerable, but further drilling is required to determine the importance of these fields. The most important increase in proven reserves resulted from the drilling to newly discovered deeper producing formations in the Elk Basin and other fields of the Big Horn Basin area of northern Wyoming. Lack of a market and unfavorable prices for heavy black oils had prevented complete exploration of favorable areas in the Rocky Mountain region for many years. In particular, the effect on further exploitation of the Big Horn Basin area had been quite serious. The increased demands for all oils created by the war and an increase in price in February 1943, combined later with Government approval of construction of pipe lines from the Big Horn Basin area to the Billings and the Casper districts, provided a basis for undertaking a drilling program. The important additions to reserves were made by drilling in previously discovered fields. The newly discovered fields resulted from drilling on favorable structures which had been known for several years. A continuation of the favorable results obtained during 1943 seems possible only if further testing of the newly discovered fields is satisfactory and if drilling on less favorable known structures or geophysical prospects results in the discovery of new fields. The amount of drilling in the Rocky Mountain states of Colorado, Montana and Wyoming, was about the same during 1943 as .in 1942. However, owing to the fact that a number of wells of large potential production were completed in the Elk Basin field, the total initial production of the prodicing wells was- nearly twice as great for 1943 as for 1942. Explorational activity at the end of 1943 seemed to be directed to geophysical methods, which are required to discover structures hidden beneath the rocks of Tertiary age in the Powder River and other large sedimentary basins. It is in

Jan 1, 1944

By Gail F. Moulton, C. E. Shoenfelt

Proven and developed oil reserves, and productive capacity increased during 1943 in the fieids of the Rocky Mountain region. Oil production during the year was nearly 45 million barrels, or slightly less than in 1942. The rate of production at the start of 1944 was slightly less than at the start of 1943. Pipe-line projects scheduled for completion during 1944 should permit a substantial increase in the rate of production. Wildcat exploration was more extensive in Montana during 1943 than in other states in the region. The results of wildcat drilling were unsatisfactory, although new oil fields were discovered on the Gebo, Little Buffalo Basin and Steamboat Butte structures of Wyoming, the Gage anticline of Montana, and the Clark Lake structure of Colorado. The area of the structures on which the discovery wells were drilled is known to be considerable, but further drilling is required to determine the importance of these fields. The most important increase in proven reserves resulted from the drilling to newly discovered deeper producing formations in the Elk Basin and other fields of the Big Horn Basin area of northern Wyoming. Lack of a market and unfavorable prices for heavy black oils had prevented complete exploration of favorable areas in the Rocky Mountain region for many years. In particular, the effect on further exploitation of the Big Horn Basin area had been quite serious. The increased demands for all oils created by the war and an increase in price in February 1943, combined later with Government approval of construction of pipe lines from the Big Horn Basin area to the Billings and the Casper districts, provided a basis for undertaking a drilling program. The important additions to reserves were made by drilling in previously discovered fields. The newly discovered fields resulted from drilling on favorable structures which had been known for several years. A continuation of the favorable results obtained during 1943 seems possible only if further testing of the newly discovered fields is satisfactory and if drilling on less favorable known structures or geophysical prospects results in the discovery of new fields. The amount of drilling in the Rocky Mountain states of Colorado, Montana and Wyoming, was about the same during 1943 as .in 1942. However, owing to the fact that a number of wells of large potential production were completed in the Elk Basin field, the total initial production of the prodicing wells was- nearly twice as great for 1943 as for 1942. Explorational activity at the end of 1943 seemed to be directed to geophysical methods, which are required to discover structures hidden beneath the rocks of Tertiary age in the Powder River and other large sedimentary basins. It is in

Jan 1, 1944

By W. A. Wall, R. L. Kidd

IN present-day flotation practice, grinding of the flotation feed is carried to extremely fine sizes, 70 to 80 per cent minus 200 mesh being customary. The greatest flotation losses occur in the coarsest and finest sizes, but the losses in the very fine sizes are, of course, much the more important because of the large proportion of fines in the feed. These losses are particularly high in zinc ores so a study of the effect of size on the flotation of sphalerite has been made. The mineral used in these experi¬ments was a pure sphalerite, especially free from copper, from the Joplin district in Missouri. The sizes coarser than 200 mesh were separated by screening, the sized mineral then being deslimed on a Wilfley table. The sizes finer than 200 mesh were obtained by water elutriation as described by H. R. Bradford (M. S. Thesis, University of Utah, 1932) ; particles finer than 6.5 microns could not be obtained with the apparatus used.

Jan 1, 1933