Search Documents

By E. W. Wagy

The year 1927 witnessed numerous developments of significance in California. The State's shut-in production increased from an average of 58,000 bbl. daily in January to a maximum of 93,000 bbl. daily in August, and a total of about 25,000,000 bbl. was withheld from the market during the year. This not only lessened the effect of large production at Hunt-ington Beach, Seal Beach and Alamitos Heights, but also was a most effective conservation move. Since 1922, it is estimated that approximately 100,000,000 bbl. of oil that would otherwise have been produced have been held in the ground. I. Outstanding Field Developments of 19271 1. Long Beach Deep Sand. 2. Rincon (Seac1iff)Discovery. 3. Alamitos Heights Discovery. 4. Ventura Avenue Extension. 5. Round Mountain Discovery. 6. Mt. Poso Extension. 7. Potrero (Cypress) Discovery. 8. Buttonwillow Gas Development. 9. Goleta Discovery. 10. Union Avenue, Edison and Fruitvale Areas. (See Fig. 1.) II. Crude Production The most important factor in new crude production in 1927 was the Seal Reach field with its adjacent Alamitos Heights townlot area. Production increased from about 10,000 bbl. daily in January, to a peak of 66,000 bbl. in June. Huntington Beach finished the year 1926 with a production of 102,000 bbl. daily, which declined to 60,000 bbl. by the end of 1927. Due to production in these three areas and the tempering effect of shutting in numerous wells, the California production curve for 1927 was held at a fairly even level. Fig. 2, shows the State's production in 1927 and 1926 as compared with 1923, which was the year of excessive

Jan 1, 1928

By R. Taggart, R. H. Ericksen, D. H. Polonis

MarTENSITIC a has been observed to form spontaneously from the retained ß phase during the preparation of thin foil specimens of metastable Ti-Cr alloys containing from 6.9 to 20 wt pet Cr. Similar spontaneous martensite reactions have been reported in thin foils of 0 brass' and other alloys.2 4 The absence of retained austenite in iron-based alloys has also been attributed to spontaneous decomposition during thinning.5 The present work indicates that a unique situation occurs during which the spontaneous transformation takes place when the transitional ? phase is present in the as-quenched or partially aged ß phase. Alloys containing 6.9, 7.0, 8.0, 12.0, and 20.0 wt pet Cr were prepared by the levitation melting of "io-chrome" chromium and iodide titanium. The 0.5-in.-diam ingots were vacuum-annealed at 1000oC, and wafers 0.020 in. thick were then cut from the ingots. These wafers were wrapped in molybdenum foil, encapsulated in Vycor under a reduced pressure of purified helium, and then held for 30 min at 1000°C. The specimens were quenched in water to retain the metastable high-temperature ß phase. The quenched alloys were thinned by mechanical grinding to about 0.005 in. thick, then electropolished in a solution of 300 ml methyl alcohol, 175 ml n-butyl alcohol, and 30 ml perchloric acid at a temperature of -40°C. Needle specimens 0.005 to 0.010 in. diam were taken from each ingot and heat-treated with the foil specimens. X-ray diffraction patterns indicated the structure of the 6.9, 7.0, and 8 wt pet alloys to be a

Jan 1, 1968

By H. R. Peiffer, R. Geckle

The silver phase of silver and finely divided alumina composites is shown to grow as single crystabs upon solidification from the melt. These crystals grow without the aid of an externally applied thermal gradient or a mold. The single-crystal growth is more readily disrupted as the alumina content varies from the optimum concentration of 20 wt pct. Pretreatment such as variation of fabrication pressure, and presintering of the specimens appear to play a lesser role in this phenomenon. In actual practice the growth of single crystals of metals from the melt is a tedious, painstaking process.' Care must be taken to insure the proper thermal gradients and rate of growth in a vibration-free environment. Excellent single crystals can be grown when these variables are controlled. When a second insoluble and finely divided phase is present in the melt the growth of single crystals is difficult, if not impossible, even under the most favorable conditions outlined above. During the past few years, a composite of silver and alumina has demonstrated an ability to resist flow even though the major phase, silver, is mo1ten. 2 A more surprising feature of this material is the ease with which single crystals of silver grow upon cooling the composite from temperatures above the melting point of silver to temperatures near room temperature. Observations have been made that demonstrate that single crystals of silver will grow even when conditions most unfavorable for growth of pure silver crystals exist. The crystals grown in this manner are imperfect in that a great deal of subgrain structure exists. It is the purpose of this manuscript to qualitatively describe this process and to attempt to isolate the influencing factors of this behavior. MATERIAL PREPARATION The composite material is prepared by powder-metallurgical techniques. Two items of great importance are the introduction of oxygen into the system and the obvious need for a thorough mixing of the metallic and refractory oxide phases. The oxygen is necessary in order that the silver wets the alumina. Without oxygen the phases separate and the material shows no unusual properties. In order to supply the needed oxygen the silver is added in the form of silver oxide which is readily decomposed to oxygen and silver upon heating. The silver oxide is readily obtained in a finely divided form that allows a uniform mixture of the alumina and silver oxide to be prepared. The correct ratio of alumina to silver oxide is mixed in the presence of alcohol in an ordinary food blender. The mixture has the consistency of a thin slurry and after mixing for approximately 20 min is dried and pressed into billets at various pressures. As is shown in Fig. 1, there is no limit to the shape of the specimens obtainable as single crystals. These billets are heated in air in a predeter-

Jan 1, 1964

By Ursula E. Wolff

The precipitation of carbides from an alloy containing 33 pct Ni, 21 pct Cr, balance iron, was investigated electron microscopically by means of extraction replicas and thinned metal foils. Annealing temperatures ranged from 565°to 870°C and up to several thousand hours. M23C6 precipitated in pain boundaries, incoherent and coherent twin boundaries in that sequence. The orientation relationship between carbides and austenite matrix was determined and correlated with the morphology of the carbides and with the type of boundary in which precipitation occurred. In large-angle grain boundaries, as well as in coherent twin boundaries, the carbides had the same orientation as one of the adjacent pains. These carbides formed sheets of individual flakes with shapes related to the orientation of the boundary. In incoherent twin boundaries carbides precipitated in ribbons composed of pavallel rods. An unidentified subcarbide was found to precede precipitation of M23C6 in these boundaries. The M 23 C6 rods had a kind of fiber texture with (110) parallel to the long dimension of the rods and ribbon, and with orientations of both of the adjacent twin-related austenite crystals Predominant in the texture of the carbide. A hard sphere crystal model has been used to discuss orientation and morphology of the carbides in terms of free volume and vacancies available in the boundaries. A number of papers have dealt with the morphology of chromium carbide (M23 C6) precipitated in austenitic stainless steels.1"7 In all these investigations, the carbides were examined in the electron microscope by means of extraction replicas. With this technique, the carbides retain the spatial distribution they had in the bulk sample. However, since the matrix is dissolved in the process, the particles can turn in an unpredictable way; and the orientation relationship between matrix and carbides cannot be established. In this paper the results of studies on extraction replicas and on thinned metal foils are reported. These studies were undertaken to determine the matrix-to-car bide orientation relationship, and to correlate the orientation of the carbides with their morphology. PROCEDURE The material used was an austenitic alloy with 33 pct Ni, 21 pct Cr, balance iron, containing approximately 0.05 pct C. Coupons of 1.25-mm sheet were first solution-annealed at 1050°C for 15 min and air-cooled. Then, to precipitate the carbides, samples were isothermally annealed in the range from 565" to 870°C for times up to several thousand hours. All further specimen-preparation procedures were carried out after the final anneal. Carbon extraction replicas from polished and etched surfaces were made with 10 pct bromine in methyl alcohol.' Thin foils were prepared from punched-out 3-mm-diam disksg which fit into the electron-microscope holder. The disks were prethinned by grinding to approximately 0.5 mm thickness, and then electro-polished in a polytetrafluoroethylene holder1' with a solution containing 5 pct perchloric acid in acetic acid to which 10 g per 1 Cro3 and 5 g per 1 nickel chloride were added (etchant modified from that of Briers et al."). This solution dissolves neither the carbides nor the austenite around the carbides preferentially. By using extraction replicas, electron micrographs and selected-area electron-diffraction patterns were taken from the same carbide arrays. By using thin foils, electron micrographs were made from a grain boundary area containing carbides. Electron-diffraction patterns were then taken from the same area and from each of the adjacent grains separately. In this manner, the orientation of each grain could be determined without interference by the carbide pattern. A peculiarity of extraction replicas should be pointed out. After the matrix is etched away, the carbide arrays float freely in the etching and washing solutions, and are held in place only at the anchoring points in the carbon replica. When the replica is picked up with a screen the carbide arrays tend to flip to one side. Thus, while the surface features are preserved, the original arrangement of the carbides may severely and unpredictably be disturbed whenever the specimen contains large amounts of interconnected carbides. Nevertheless, it is possible to correlate the different morphologies of the carbides with the type of boundary in which they have precipitated. RESULTS 1) Extraction Replicas. Fig. 1 shows that the grain boundaries usually are curved, multicornered surfaces of random orientation. The coherent twin boundaries (which are (111) planes) cut a grain into parallel slices. Incoherent twin boundaries occur at the ends and on the steps of twins and are often narrow, parallel-sided strips which are much longer than they are wide. Different morphologies can clearly be distinguished for the M23Ce carbides precipitated in each of these types of boundaries, and agree well with those observed by kinzel.2 The kinetics of this precipitation has been investigated." The first carbides precipitate in junctions of three grain boundaries and fan out from there into the adjoining boundary surfaces, Fig. 2(a). These carbides are oriented randomly, Fig. 2(b), and become coarser and thicker as annealing time increases. The large-angle grain boundaries are next to fill

Jan 1, 1967

By D. J. Schmatz

DISCUSSION OF RESULTS The qualitative correlation between low-temperature ductility and prior high-temperature creep strain in nickel obtained in this investigation confirms the result obtained on high-purity brass by Chen and Machlin. However, the quantitative effect is much smaller in nickel. Comparison can be made on the basis of a prior high-temperature strain that is a certain percentage of the total high-temperature elongation to rupture. In the research of Chen and machlin, the prior high-temperature strain of 1/2 pct equaled 8.5 pct of the total high-temperature elongation at rupture. For nickel, in our experiments, 8.5 pct of 21.2 pct equals 1.8 pct. For eh = 1.8 pct, the loss in ductility in percent equals x 100 = b.5 pct. That is, for equivalent bo Formation of Beta Manganese-Type Structure in Iron-Aluminum-Manganese Alloys D. J. Schmatz IRON-aluminum alloys have gained much interest in the past few years for use as a base material for elevated-temperature alloys because of their excel- high-temperature strain the loss in low-temperature ductility is 8.5 pct for nickel as compared to 60 pct for pure a, brass. It is also interesting to note the observation that in nickel the low-temperature fractures, even at the most extreme high-temperature pre-strain, were partly trans crystalline and partly intercrystalline. In the case of a brass, these fractures were completely intercrystalline. According to the data on the percent of the grain boundary area that is cracked, at 22 pct high-temperature elongation, about 12.5 pct of the grain boundary area does not carry load. Thus, the inter-crack areas are carrying a stress that is about 11 pct higher than the nominal stress. A simple model predicts that the overall elongation, which is primarily the elongation in the bulk of the specimen, will correspond to the nominal stress when the stress in the intercrack area equals the tensile strength. Quantitatively this model predicts the equation The form of this equation will agree with that found if the strain-hardening exponent, n, equals unity. Actually this model is too gross an approximation to yield good quantitative results. The question naturally arises as to whether in ordinary hot-working, such as hot-rolling, intercrys-talline cracks are introduced that affect the low-temperature properties. It appears that the answer is that such a possibility cannot be overlooked, if the hot-working induces tensile stresses at temperatures above the equicohesive temperature and if the material tends to be notch sensitive at low temperature. ACKNOWLEDGMENT This research was supported by the Aeronautical Research Laboratory, Directorate of Research, Wright Air Development Center, United States Air Force. REFERENCES lC. Zener: Fracturing of Metals, 1948, Cleveland, ASM. 'H. C. Chang and N. J. Grant: Mechanism of Intercrystalline Fracture. AIME Trans., 1956, voL 8, p. 544; lownal of Metals, May, 1956. 'E. S. Machlin. CreepRupt ure by Vacancy Condensation, AIME Trans., 1956, vol. 8, p. 106; lownd of Metals, February, 1956 'C. Chen and E. S. Machlin: On a Mechanism of High-Temper at ure Inter-crystalline Cracking, lownd of Metals, July. 1957. p. 829. Alloys lent oxidation resistance. Binary alloys of aluminum in iron are ferritic and consequently have poor hot strength. Alloys of iron-aluminum-manganese were made in an attempt to produce an austenitic alloy containing sufficient aluminum to retain the oxidation resistance of binary alloys of iron-alumi-

Jan 1, 1960

By H. Wilton Clark

VARYING in thickness and in number from place to place, coal seams in the Canadian Rockies also range in pitch from nearly horizontal to vertical, sometimes with overturns. Over the entire coal-bearing area there are considerable differences of rank in coals of the same geological age, and there are marked differences in ash content and wash-ability characteristics. Correlation of seams at mining operations within a few miles of each other has often proved impossible. These factors influence mining methods, and, of course, production results. The oldest coal formations of western Canada are of Lower Cretaceous age, as the carboniferous sediments are marine and contain no coal. Coal is also present in formations of Upper Cretaceous and Tertiary ages. The rank of coal varies from semi-anthracite in some operations in the Kootenay and Luscar formations of the Lower Cretaceous in the Rockies to lignite in the Tertiary fields of the Saskatchewan prairies. Fig. 1 shows the general extent of the formations. The pitching seams, chiefly Lower Cretaceous, occur in the western belt of the Rocky Mountain foothills and the eastern slopes of the Rockies themselves. (The road to Tent Mt. strip pit, elevation 7000 ft, is shown on p. 832.) Formations extend from the U. S.-Canadian boundary for several bundred miles in Alberta and continue for a similar distance in British Columbia. Present geological estimates show a probable reserve of the order of 25,000 million tons of coal ranging from high volatile bituminous to semi-anthracite, with a large percentage of coking coal, constituting one of the major world reserves of that type. It should be noted that although the quoted estimate probably errs on the conservative side, the question of access to the seams in a mountainous terrain will always be a problem; a wide divergence may exist between actual reserves and the quantities of coal economically recoverable. An excerpt from the Canadian government Report of the Royal Commission on Coal 1946 states that conditions favorable to coal formation were intermittent and these intervals relatively brief in comparison with periods in which no coal was formed. Conditions were favorable to the growth or accumulation of vegetation in one area, while fresh water sediments and marine shales were being deposited in other areas. During periods of emergence the coal deposits were subjected to erosion or were covered by coarse sands and gravels from the mountains, whereas during submergence they were covered by fine clays deposited in embayments of the sea. During some of the periods of coal formation, volcanic activity deposited beds of fine volcanic ash and dust with the coal-forming vegetation. Coal deposits reach their greatest development in the mountains and thin rapidly to the east into the plains area, where they are deeply buried beneath younger sediments. For example, in the Fernie area of southeastern British Columbia there are in places 22 seams having an aggregate thickness of 150 ft in a stratigraphic interval of 3500 ft, whereas at Cole-man in the Alberta Crowsnest area the measures are only 800 ft in thickness and contain a maximum of five seams aggregating about 47 ft of coal. At Belle-vue, 10 miles further east, the measures are reduced to 430 ft with only three seams aggregating about 37 ft of coal. Subsequently the tremendous forces involved in the upthrust of the Rocky Mountains produced great displacement of the coal-bearing formations and at the same time a change in geologically young coals from low to high rank. The floor or footwall of most seams consists of carbonaceous shales, which are almost as adaptable to bending as the coal seams themselves. The seams show very few cleats or cleavage planes and have been so weakened structurally that as mined 50 pct or more will pass through a ¼-in. screen, seldom

Jan 1, 1955

By E. A. Metzbower

STEREOGRAPHIC projections of hcp metals depend upon the c/a ratio. Hu1 has recently published standard projections for titanium (c/a = 1.5873) of the (000l), the basal plane, the (1010), the most prominent slip plane, and the (1012), the most prominent twinning plane. Caplan et a1.2 and Hul have also published tables of angles between poles of planes, between directions, and between directions and poles of planes. From these tables standard projections and double stereograms can be constructed. However, by using the on-line CALCOMP plotter with a CDC 3800 computer, direct plots of standard stereographic projections of titanium (c/a = 1.587) have been made.

Jan 1, 1970

By R. F. W. Pease, R. A. Ploc

A scanning electron microscope with a resolving power better then 100Å has been developed for the direct examination of surfaces. This instrument was used to study iron undergoing oxidation at 500°C. It was found that the electron current in the scanning electron microscope was low enough (about 10-atrzp) to have no observable effect on the growth of the oxide. "Armco " iron, when oxidized, exhibited an oxide film whose thickness and whiskey population varied with pain orientation; but purer iron, when oxidized, exhibited no such pain dependence and whisker occurrence appeared to be caused by impurities. UNTIL recently most surfaces of opaque specimens could either be studied with a light microscope or, if higher resolution was required, by viewing a replica of the surface in a transmission electron microscope. Direct electron microscopy of a surface has, in general, proved difficult owing to excessive foreshortening and the poor image quality obtained. The scanning electron microscope, however, offers an alternative method of directly viewing a surface without these disadvantages. At low magnification it offers a much larger depth of focus than the light microscope, and at high magnifications it offers much higher resolution (about 100Å). PRINCIPLE OF THE SCANNING ELECTRON MICROSCOPE A schematic diagram is shown in Fig. 1. The electron optical system consists of a gun followed by a series of lenses which focus the electron beam onto the surface of the specimen. The beam is scanned in a rectangular raster across the specimen surface and, by amplifying the secondary electron current from the 'pecimen, a picture of the specimen surface is built UP sequentially on the face of the display cathode-ray tube. The magnification of such a system is given by the ratio of the scan amplitude on the display cathode-ray tube to

Jan 1, 1965

By R. D. Pehlke, P. D. Goodell, R. W. Dunlap

The rate of dissolution of steel bars in molten pig iron has been measured experimentally in the temperature range 2300° to 2650° F. The rate of solution is shown to be a .function of bath composition, temperature, and stirring. A kinetic model based on carbon diffusion in the liquid phase has been derived to fit the experimental results. THE rate of scrap melting has long been an important variable in steelmaking operations. With the advent of the oxygen steelmaking process and the accompanying shorter heat times, the rate of scrap melting has now become one of the rate-limiting factors in steel production. As observed in commercial practice, the solution rate is influenced by the compositions of liquid and solid, the temperature, agitation, and time. However, no definitive work has been done on the Fe-C system, and there is very little information in the literature regarding the relative effects of these variables in steelmaking systems. A number of questions have been raised in regard to scrap utilization in basic oxygen steelmaking operations. Consideration has been given to the optimum size and shape of scrap, and to the use of preheated scrap as a means for decreasing the pig-iron requirement in oxygen blowing. The determination of an optimum scrap practice for a specific installation depends to a large extent upon the economics of the scrap market and also upon the behavior of scrap in the vessel. The present research was undertaken as a preliminary study in evaluating the behavior of steel in a pig-iron bath under various conditions of temperature, composition, and agitation, as might be encountered in oxygen converter operations or in any steelmaking operation where scrap behavior is an important process variable. Related studies have been carried out on non-ferrous systems. The solution rate of solid aluminum in a molten A1-Si alloy has been studied.' Furthermore, the increasing use of liquid metals has created considerable interest in studies related to dissolution of a solid in a liquid, or mass transfer taking place between a solid interface and a liquid metallic phase.2-10 In an effort to clarify the relative importance of factors influencing the dissolution of scrap in Fe-C alloys, this paper presents the results of a study of the rate of dissolution of a low-carbon steel cylinder in a molten Fe-C bath at various bath compositions, temperatures, and conditions of agitation. An attempt has been made to determine the mechanism of solution, and a model has been derived to fit the experimental results. The rate of heat transfer between the molten pig-iron bath and the solid-steel cylinder has also been studied. EXPERIMENTAL PROCEDURE A molten bath of pig iron (nominal composition 4.2 pct C, 0.5 pct Mn, 0.8 pct Si)* was held in a 200- *In view of the fact that the composition of the pig-iron bath was slowly changing with time because of steel dissolution and reaction with the surrounding atmosphere, intermittent samples of the liquid bath were taken throughout each experiment, Table 1. lb induction melting unit. The internal diameter of the furnace was 8-1/2 in. and the bath depth approximately 14 in. Cold-finished 1020 steel cylinders of 1/2-, 3/4-, 1-, 1-1/2-, and 2-in. diameters were cut into 1 -ft lengths for use as test specimens. One end of each bar was machined to fit a hand-driven, mechanical stirring device which rested on top of the furnace. This fixture permitted 7 to 8 in. of the bar to be immersed in the melt. The steel cylinders were cleaned to free the surface of grease and oxide. The rods, at ambient temperature, were immersed into the molten pig-iron bath. The melt temperatures studied in this investigation were 2300°, 2500°, and 2650°F. Different agitation conditions were achieved by operating with a) the power to the furnace, giving induction stirring; b) induction stirring plus mechanical stirring, using hand rotation with a chain and sprocket assembly at approximately 200 rpm; c) mechanical stirring alone with the power off; and d) the power off and no mechanical stirring resulting in minimum agitation, i.e., only that caused by natural convection currents in the bath. The samples were immersed in the melt for prescribed times ranging from 30 sec up to 6 min. Immersion times were measured with a stopwatch and temperature control of the melt was achieved by power adjustment following temperature measurement with an optical pyrometer. The measurements with the calibrated pyrometer were checked out to within less than 10°F with simultaneous thermocouple measurements. Following immersion, the bars were water-quenched and the diameters were measured with a micrometer at several positions on the reduced area, and by volumetric displacement. The dissolution rates calculated from the

Jan 1, 1965

By A. G. Journel

Accurate prediction of recoverable reserves are key to the development and planning of a mining operation. Recovery functions for tonnage, quantity of metal, and ore grade are defined and two approaches for their estimation are proposed. The indicator kriging (IK) approach draws on the data rank orders, whereas the multigaussian (MG) approach relies on a grade multivariate distribution hypothesis. Although based on different premises, both approaches yield remarkably similar, and reasonably accurate, estimates for recoverable reserves.

Jan 1, 1986

By B. N. Bose, M. F. Hawk

SINCE Davenport and Bain' introduced the isothermal transformation technique for the study of austenite decomposition in steels, a new field of investigation has opened up. Extensive research has been carried out on many different steels, but relatively little work has been done on eutectoid transformations in analogous alloy systems. The researches of Smith and Lindlief,² Mack,³ and Klier and Grymko²0 on the beta-phase transformation in copper-aluminum alloys, of Hibbard, Eichelrnan, and Saunders4 and Smith5 on the kappa-phase transformation in copper-silicon alloys, of Chaudron and Forester6 on the decomposition of "FeO," and of Wasserman7 on similarities between the iron-carbon, copper-aluminum, copper-tin, and copper-beryllium systems essentially comprise the field. The iron-nitrogen system, in view of its remarkable similarity to the iron-carbon system, is particularly attractive for the study of eutectoid decomposition. The present investigation is concerned with the study of isothermal transformation, proceeding by the familiar nucleation and growth processes, and of martensitic transformation characteristics of pure iron-nitrogen alloys. The kinetics of transformation and the morphology of the transformation products have been investigated, for these must be the factors determining the properties and behavior of the final product. The Iron-Nitrogen System he binary iron-nitrogen phase diagram has been a matter of considerable disagreement among vari01.1s investigators. However, the phase diagram according to Eisenhut and Kaupp8 and Lehrer10 is now considered essentially correct as reproduced in fig. 1. The important values, 2.35 pct nitrogen and 591°C, for the co-ordinates of the eutectoid point (obtained from this diagram and used in the re- search to be described) were confirmed in a concurrent study of Paranjpe, Cohen, Bever and Floe." The eutectoid decomposition involves the transformation of the ? face-centered cubic interstitial solid solution of nitrogen in iron to the a body-centered cubic interstitial solid solution of nitrogen in iron and the ?' nitride of iron. This nitride is essentially the compound Fe,N; it also possesses a face-centered cubic lattice but a considerably larger one than the ?; the nitrogen atoms in ?' are arranged in an ordered way in the centers of the unit cubes.8,10,11 A martensitic structure has also been reported8,12 in iron-nitrogen alloys and was studied in the research to be described here. Materials and Methods The specimens used in this investigation were prepared by nitriding "pure" iron. This iron was supplied by the Westinghouse Research Laboratories and is the product bearing their trade name "Puron"; it contains about 0.04 wt pct total impurities, the major portion of which is oxygen. Specimens were ribbons several inches long, a tenth of an inch wide, and 0.125 mm thick; this was the

Jan 1, 1951

By R. A. Matuszak

Throughout the history of power excavating machines, engineers have continuously tried to shape the main drive speed- torque characteristics to provide an optimum from each main motion. Selection of prime mover for the various motions has been the subject of many engineering studies and most forms of energy conversion have been tried. A new form of electrical power conversion looms on the horizon as the most optimum yet. Controlled frequency operation of a squirrel cage induction motor increases the reliability of the most reliable form of energy conversion (electrical) found thus far, and improves the performance characteristics.

Jan 1, 1979

By R. A. Matuszak

Abstract-Throughout the history of power excavating machines, engineers have continuously tried to shape the main drive speed-torque characteristics to provide an optimum performance from each main motion. Selection of prime mover for the various motions has been the subject of many engineering studies and most forms of energy conversion have been tried. A new form of electrical power conversion looms on the horizon as the most optimum yet. Controlled frequency operation of a squirrel cage induction motor increases the reliability of the most reliable form of energy conversion (electrical) found thus far, and improves the performance characteristics.

Jan 2, 1978

By Robert A. Bauer

This study showed that diametral point-load testing performed parallel to the bedding planes of highly anisotropic sedimentary rocks produced inconsistent results that cannot be used to accurately estimate uniaxial compressive strength. Axial point-load values from tests performed normal to bedding planes and evaluated by the T500 index produce good correlations with the uniaxial compressive strength values obtained for five different rock types. A strong correlation also existed between the moisture content and the uniaxial compressive strength of the tested lithologies. A combination of axial point-load and moisture content indices produces the best correlation with the uniaxial compressive strength test results.

Jan 1, 1984

By C. G. Dunn, F. W. Daniels

IN recent publications1-5 the existence and behavior of subgrain boundaries in high-purity metals has been clearly brought to light. Lacombe and Beaujardl by means of special etching methods disclosed in polycrystalline sheets of aluminum the existence of substructures differing in orientation by small amounts (about 1/4"). Boundaries of these structures at relatively high temperatures had the remarkable property' of moving about while the ordinary boundaries remained stationary. Cahn2 also observed substructures in bent and annealed single crystals of aluminum, zinc, magnesium, and rock salt. The position of subboundaries could be explained in terms of a dislocation mechanism of polygonization in which dislocations move into lines at right angles to the bent glide planes thereby relieving elastic stresses in these planes. Guinier and Tennevin8,6 disclosed the further interesting feature that polygonized structures coarsened significantly upon prolonged annealing. Somewhat similar subgrain phenomena have been observed in silicon iron of commercial purity. Although some evidence for the development of macro-mosaic structures in silicon iron already has been reported by one of the authors6,7 under the phenom-enological term "crystal recovery," much better evidence recently has been obtained due to improved etching techniques. In addition, phenomena regarding structural changes have been uncovered. The present investigation is divided into three parts: (1) The phenomenon of Laue spot sharpening on annealing cold-rolled crystals, (2) the phenomena of polygonization and subgrain coarsening The material used in the present investigation was high-grade commercial silicon iron sheet of nominal composition, 3.3 pct Si, 0.004 C, 0.011 P, 0.010 S, 0.04 Mn, 0.01 Al, 0.04 Cu, 0.01 Sn. Large single crystals of this material Were prepared for cold-rolling or bending as scheduled. Cold-rolling of 12 pct was carried out on a laboratory 8-in, diam rolling mill. The bending deformations were performed by pressing the crystals between a solid Fig. 2—lllustrative foue patterns to show Laue spot sharpening. a (Left)—Specimen as cold rolled, b (right)—After 48 hr at 1400°C. round bar and a mating half cylinder, both heavily greased. Individual specimens were cut from the deformed crystals, and the cut edges were deeply etched prior to annealing. Laue photographs were made using 40-kv tungsten radiation. The technique used to disclose the various subboundaries was an electropolish and electroetch in a bath of chrome-acetic acid.' The anodic polishing done at 22 v was immediately followed by etching at a reduced voltage, which was dependent upon the nature of the subboundaries. Phenomenon of Laue Spot Sharpening on Annealing Cold-Rolled Crystals Fig. 1 gives the initial and final orientations of the specimens cold-rolled 12 pct. Each specimen was annealed at a temperature and for a time which caused significant structural changes as evidenced by alterations in Laue patterns. Representative Laue patterns and micrographs showing the essential changes are given in Figs. 2, 3, and 4. The essential points to be derived from these illustrations follow: 1. Annealing at 950°C clearly develops a substructure with the orientation of the cold-rolled specimen. 2. The subboundaries formed obviously separate regions of nearly the same orientation. Some of the subboundaries appear as a sequence of dots similar to those observed in aluminum by Lacombe and Beaujard,' but whether this is due to extremely small differences in orientation is not known at present. 3. The substructure coarsens upon prolonged annealing. 4. Prolonged annealing also causes a decrease in orientation spread according to Laue spot sharpening'

Jan 1, 1952

By R. M. Jorda

The mechanism of parafin deposition and prevention has been studied in the laboratory using an apparatus which provides a quantitative means of studying parafin deposition on metal and plastic surfaces. The amount, hardness, adhesion, per cent wax and mean molecular weight of parafin deposits appear to be governed by surface roughness alone, all other conditions being constant. Tests of various plastic coatings indicate that most smooth, nonparafinic plastics are capable of reducing parafin deposits in oil wells, but flexible, highly polar, nonparafinic plastics are more suitable for providing long term resistance to parafin deposition in oil wells if the flow stream contains abrasive materials. INTRODUCTION The problem of paraffin deposition is one of long standing in the oil industry.' Crude oils often contain paraffins which precipitate and adhere to the liner, tubing, sucker rods and surface equipment as the temperature of the producing stream decreases in the normal course of flowing, gas lifting or pumping. Heavy paraffin deposits are undesirable because they reduce the effective size of the flow conduits and restrict the production rate from the well. Where severe paraffin deposition occurs, removal of the deposits by mechanical, thermal or other means is required, resulting in costly down time and increased operating costs. The troublesome paraffins are normal hydrocarbons ranging from approximately C15H38 to C38H78 mixed with small amounts of branched paraffins, monocyclic paraffins, polycyclic paraffins and aromatics.' The amount of paraffins found in crude oils varies from less than 1 to more than 30 per cent. Many publications are available which deal with this problem, and perhaps the most significant findings in recent literature are contained in a publication by Hunt3 ho developed the "cold spot tester", a really useful means of investigating paraffin deposition. Hunt's observations led to many generalized conclusions concerning the effect of surface roughness on paraffin deposits. He ascertained that there was an observable qualitative correlation between the severity of paraffin deposition and the roughness of the surfaces which he tested (cold rolled steel, stainless steel and several plastics). Because of the number of meaningful observations made by Hunt, his cold spot tester was modified somewhat and extensive tests were per- formed to study the quantitative relationship between surface roughness and the physical and chemical nature of paraffin deposits. LABORATORY TEST PROCEDURES The cold spot test apparatus consists of a flat circular plate mounted on a curved tube and positioned in a vessel containing a wax-oil solution (Fig. 1). The apparatus is arranged so that the temperature of the central portion of the circular plate can be varied by means of a circulating liquid stream; the test equipment includes provisions for maintaining a constant wax-oil solution temperature and stirring speed. In the paraffin deposition studies, the modified cold spot tester was used as follows. The cold spot probe consisted of a flat circular plat 2 in. in diameter and 1/8-in. thick positioned in the wax-oil solution kept at constant temperature. As in Hunt's earlier experiments," a cold liquid was circulated through a tube connected to the circular plate so that the liquid impinged on one side of the plate cooling the plate from the center outward, causing paraffin to deposit on the side of the plate exposed to the wax-oil solution.

Jan 1, 1967

By L. D. Fetterolf, G. T. Mahler, W. M. Peirce, R. K. Waring

UNTIL recently, the only commercial method of producing magnesium has been fused salt electrolysis, despite a considerable amount of experimental work on the direct reduction of magnesium oxide. In this early work, a number of investigators demonstrated that magnesium oxide would react with any one of several reducing agents to produce magnesium vapor, but that the mixture of magnesium oxide and reducing agent must be heated to a high temperature even in a vacuum. In particular, it was demonstrated that silicon and aluminum are effective reducing agents and that when either of these is used the magnesium vapor can be condensed to massive metal. In spite of this knowledge, no successful commercial reduction process was developed, at least in this country, because of the operational difficulties imposed by the requirement of high temperature and vacuum and because of the high cost of the reducing agent. The outstanding experimental work done by Pidgeon, who carefully reviewed all of the known methods of making magnesium and then selected ferrosilicon reduction, overcame some of the operational difficulties. The process developed by Pidgeon comprises briquetting a mixture of calcined dolomite and reducing agent, pre-heating the briquets to about 600°C. in an externally heated alloy retort, reducing the MgO with silicon in an evacuated horizontal alloy retort heated externally to about 1150°C., and condensing the magnesium vapor to a solid in a cold extension of the retort projecting beyond the fr6nt of the furnace. A major advantage of Pidgeon's process is that the retort is not cooled down between charges. Earlier investigators had used apparatus that necessitated cooling and reheating of the retort between charges. Early in January 1942, when the War Production Board was considering the Pidgeon process for quickly increasing the production of magnesium, The New Jersey Zinc Co. offered to have a research investigation of the process carried on, with the hope of assisting in its further development. This offer was accepted, and a two-retort pilot plant was built at Palmerton and put in operation on Jan. 29, 1942. An intensive investigation of certain phases of the process was carried out in the ensuing four months. This investigation was completed in the last part of May 1942, and the pilot plant was then shut down. Subsequently, The New Jersey Zinc Co. was requested to have further development work done on the process, and a more extensive investigation was undertaken in August I942 under contract with the War production Board and under the super- vision of the War Metallurgy Committee. This paper describes the phases of the investigation that are thought to .be

Jan 1, 1944

By D. K. Crampton

Internal stress and season cracking in brass have been studied for many years and the technical literature contains many data on various phases of the subject. A resume of the literature shows certain fairly well established points upon which various authors are mostly agreed: 1. Season cracking is primarily caused by the presence of relatively high internal stresses, or possibly in some cases by external stresses, or both. 2. A specific corrosion is also essential to season cracking. Certain agents, particularly mercurous salts, mercuric salts and ammonia salts, have such a specific corrosive effect. 3. The tendency to season crack under given conditions increases with increasing zinc content, brass containing less than 20 per cent. zinc being relatively immune. 4. In alpha brass the season cracks are intercrystalline; in alpha-beta brass they lie between the two constituents; and in beta brass they are transcrystalline. 5. The ordinary impurities or added elements in special brasses have little or no effect on the tendency to season crack. 6. Internal stresses can be eliminated, or at least reduced to a safe limit by annealing treatments at temperatures that do not produce visible microstructural changes or appreciable softening of the worked brasses. There are, however, some points in connection with the phenomenon of season cracking which have not been thoroughly investigated, or wherein different authors and investigators are not entirely in agreement. The investigations described in this paper were undertaken to determine: 1. The correlation between mercurous nitrate tests and actual season cracking on long-time atmospheric exposure. 2. The quantitative effect of type and degree of drawing operations on the intensity of internal stress and on the tendency to season crack in brass tubes. 3. The possibility of drawing high-brass tubes in such a manner as to prevent the occurrence of harmful stresses rather than to find a remedy for such stresses once having obtained them.

Jan 1, 1930

By A. J. Zinkl

A two-year test led to adoption of carbide insert bits at the Iron King mine. Results: greater production, lower costs, and happier miners.

Jan 4, 1951

By A. W. Cochardt

MOST of the current high temperature materials are precipitation-hardened alloys. These alloys are usually soft when quenched from a solution heat-treatment temperature, but become harder

Jan 1, 1958