Search Documents

By Charles Catlett

An examination of the census reports' for 1880, which contain a large number of complete analyses of typical American iron-ores, indicates that the existence of barium sulphate in intimate association with iron-ore is rather unusual. Of 94 analyses reported there, but four show any barium sulphate, and the maximum content amounts to 3.04 per cent. The note of the occurrence of considerable quantities of barite in connection with certain iron-ores found in the Pinar del Rio Province of Cuba may be of interest. These deposits are found near the little village of Francisco, about 25 miles west of the city of Pinar del Rio on the Western Railroad of Havana. The principal ridges are anticlines, and consist of very thick deposits of sandy shales and slates containing a large number of little veins of white quartz, which, by the gradual disintegration of the mass of the material, is left covering the surface. This quartz occasionally shows sulphide, but is generally barren of any such indication. At times lenticular masses of a more or less pure limestone mere observed in these slates. The shales, which are of light color, are occasionally talcose. The formation would tentatively be classed as the Lower Cambrian, arid the heavy ridges of comparatively horizontal limestone found in the anticlinal valleys as the Upper Cambrian. Along the crest of these slaty ridges deposits of iron-ore are found which are apparently in place, and were probably formed by replacement of masses of limestone similar to those noted elsewhere. The ready disintegration of the slates, arid the

Jan 1, 1908

By H. W. R. Wardlaw

This paper shows how the cost of the drilling operation per 100-ft drilled can be related directly to bit weight, rotary speed and hydraulic horsepower variations. This enables optimum drilling conditions to be determined in a rapid and concise manner. The paper also shows how data for such calculations cun be obtained quickly and accurately by the "drill-off" method suggested by Lubinski. Examples are given to illustrate the principles and methods used. INTRODUCTION The problem of drilling oil wells at lowest cost and hazard needs little introduction, since it has been with us virtually from the earliest days of our industry. With better understanding of the effect of the various factors of bit weight, rotary speed and hydraulic jet action, however, the problem has recently taken on a more scientific aspect, and engineers or groups of engineers have been assigned to study many of the facets of this problem not immediately apparent to the general observer. Moreover, the availability of better equipment and materials has enabled certain practices to be adopted which were hitherto impractical or uneconomic. This has paved the way for further efforts to reduce footage costs, and so on. The improvements to be made in drilling technology and cost reduction are by no means exhausted, and we still frequently hear of new records being set and new materials and equipment becoming available. Some of the analytical methods used by the author to assist in promoting faster and more economic methods of drilling, particularly in Venezuela, form the basis for this descriptive study. STATEMENT OF THEORY AND DEFINITIONS In a highly competitive industry, it is no longer permissible to regard penetration rate as the sole criterion for drilling efficiency. Every new technique, however spectacular, must nowadays be viewed in the cold light of whether it will eventually lead to lower cost per foot drilled. In the exposition which follows, therefore, actual drilling rates will play only a secondary role, and attention will be focused on the more important aspect of cost per foot drilled. Changes in drilling factors such as weight and rotary speed will be studied in the light of how they directly affect the cost of operations. The advantage of this method is twofold—(1) cost increments are indicated directly; and (2) the relationships are, surprisingly enough, simpler than those relating to drilling rates. To achieve these advantages, it is necessary to introduce a new unit of measurement which, although unfamiliar, is readily understood. The unit in question will be referred to as the "actual drilling cost factor" and will be designated by the symbol h. The unit is defined as the number of rotating hours taken to penetrate 100 ft of formation. The unit can be obtained immediately from the actual drilling rate (r) in feet per hour; thus, This latter transformation is so easily effected that it may be convenient to use h as an international symbol for drilling cost, and to delay conversion to dollars, bolivars, pounds, etc, per foot until actually required (e.g., for fiscal reasons, etc.). In actual operations, h was found to vary in a relatively simple manner with increases in bit weight. The variation in h with rotary speed was found to be somewhat more complex. However, this also could be enormously simplified by introducing a further factor known as L or relative bit life. The factor L is also defined very simply by dividing 1,000 by the rotary speed (N) in revolutions per minute.

By Carl E. Swartz

For many years kettles used in the melting and refining of lead and other nonferrous metals and alloys have been made of cast iron. The logic of this probably lies in the fact that cast iron has been known as a material of construction for vessels of this type much longer than steel, and satisfactory fabrication from it has been more easily accomplished and better understood. As the capacity of lead refineries has increased, it has been only natural to increase the size of kettles. Today kettles of 150 to 250 tons are not uncommon. As the size of the kettles increased and better shapes were designed, the uniformity of material of construction became more important. Records kept over comparatively long periods of time have shown that the length of service of kettles has not been uniform. Many causes contribute to this and the importance of each has not yet been evaluated. Kettle design, kettle setting, method of firing and material of construction have been changed from time to time to obtain better service, but the variation in length of service is still great. A kettle may fail during the first few heats or may last through more than one thousand heats. The purpose of this article is not to present the conclusions of a finished piece of research on kettle manufacture and use, but to present a series of observations made over considerable time in the hope that others will publish data and that all may be correlated into a logical scheme which will result in better service and longer kettle life.

Jan 1, 1931

By R. K. Buhr, H. Thresh, M. Bergeron, F. Weinberg

The microsegregation of nickel and chromium in directionally solidified AISI 4340 steel castings has been measured using electron probe microanalysis. Minimum concentrations were observed to occur at the center of the dendrite stalks, as reported previously. However, the position of the maximum concentrations could not be determined from the dendrite configuration. An etching technique has been developed which shows the position of maximum concentration. Measurements were made of the distribution of nickel and chromium in the dendritic structure. The ratio of maximum to minimum concentration was determined as a function of primary dendrite arm spacing for both as-cast and partially homogenized materials. The results are compared with observations reported in the literatuve. A S part of an investigation of solute segregation in directionally solidified AISI 4340 steel casting, electron probe microanalysis was used to measure the distribution of nickel and chromium in the dendritically segregated material. This complemented the observations on the segregation of radioactive phosphorus obtained by autoradiographic techniques in the same castings.' Kattamis and I?lemings2 have reported similar measurements, using electron probe microanalysis, on dendritically segregated AISI 4340 steels. They found minimum solute concentrations occurred at the center of dendrites, maximum concentrations occurred in the center of interdendritic regions, for symmetrically oriented dendrites, and a regular variation of concentration within dendrite arms. The ratio of maximum to minimum concentration was found to be essentially independent of position in the castings, except near the chill surface where it was somewhat higher. Assuming complete diffusion in the liquid and no diffusion in the solid during freezing, they considered that isoconcentration curves in the steel were homothetic. As a result, isoconcentration curves of the various elements, contour surfaces of dendrites produced by isothermal-transformation studies, and the contour of the solid-liquid interface would all be similar, and could be superimposed by a uniform expansion or contraction of the contours. Preliminary results of the present investigation suggested that isoconcentration curves were not homothetic. It was also evident that points of maximum concentration could not be predicted from the dendrite configuration. Since the ratio of maximum to minimum concentration appeared to be an important parameter in defining the overall segregation in a casting, other techniques for determining the point of maximum concentration were investigated. In addition the overall solute distribution associated with the dendritic structure was examined for both nickel and chromium, and the consistency of the distribution for neighboring dendrites was determined. METHOD Fifty-pound heats of AISI 4340 steel were cast in a manner similar to that used by Flemings et al3 with a water-cooled copper base plate and exothermic sides and top. The nominal composition of the material was C, 0.41 pct; Mn, 0.66; Si, 0.35; S, 0.012; P, 0.010; Ni, 1.88; Cr, 0.95; Mo, 0.28. The steel solidified directionally from the chill surface, with a dendritic structure which increased in dendrite arm spacing with increased distance from the chill. Results of the general investigation of the cast structure and segregation of radioactive phosphorus in these castings have been reported elsewhere.' For the present measurements, sections were cut from the casting at several distances from the chill surface. The sections were subsequently heat-treated, mounted, and then polished on a plane perpendicular to the general freezing direction of the casting. Electron probe microanalysis was carried out with the JEOL-JXA3 microprobe using a voltage of 25 kev and beam current of 0.15 µa. The take-off angle is 22 deg. Quartz crystals were used in the spectrometers and measurements made for Ka radiation from both nickel and chromium simultaneously. A thin layer of carbon was deposited on all specimen surfaces prior to examination in the microprobe. Early measurements were made on polished surfaces, with indentation marks produced by a hardness tester to indicate the area of interest. It was found desirable to use etched surfaces, as opposed to polished surfaces, to reduce sample preparation time and more readily relate the microprobe scan to the structure. To determine if this could be done, without introducing significant errors, a series of measurements were made on polished and etched surfaces of the same specimen. Both polished and etched surfaces produced similar results within normal scatter as shown in the observations. Subsequent measurements were then made on etched surfaces. Measurements with the microprobe analyzer were made by point counting, for periods of 100 sec, at 10-µ intervals. Ten-second counts were made on pure nickel and chromium standards, incorporated in the specimen mount before and after each set of measurements. The results were adjusted for background, then corrected for dead time using the expression:

Jan 1, 1969

By E. J. Pasierb, H. W. Paxton

Mavkers ill a diffusion couple in the iron-chromium system move towards the high chromium side indicating Dcr > DFe at the marker composition. By a combituztion of measurements of D& and D a: a function of composition, this is also shown independently. DFe is calculated as a function of composition. and shown to be in reasonable agreement with measured values by other workers. MEASUREMENTS of marker movements in diffusion couples have been used from time to time to demonstrate that a vacancy or interstitial mechanism may be operative. Since there is a possibility that ring diffusion1 may be operative in chromium, the present experiments are of interest in showing some non-ring mechanism in iron-chromium alloys around the equiatomic composition. EXPERIMENTAL PROCEDURE The movement of markers originally at the interface between 1-in. sq sections of pure Cr (6 mm thick) and outer slabs of 30 Cr-70 Fe alloy was followed as a function of time at temperatures from 1150" to 1425"C, in a Kanthal-wound furnace. Temperature control was +5°C over extended periods. The analyses of these alloys are given in Table I. Selection of suitable markers presented a considerable experimental problem; the eventual solution was to draw quartz rod down to 0.01 cm and seat this in V-grooves 0.01 cm deep on each side of the chromium prior to welding. A preliminary experiment in which the groove was machined in the alloy gave identical results. Welding was accomplished by passing a heavy current through specimens under moderate pressure in a helium atmosphere. This method produced good welds with a planar interface as shown by subsequent metallo-graphic investigation. Any markers which did not adequately fill their groove and showed subsequent contamination from the atmosphere during heat treatment were not considered reliable. The composite sample was ground and metal-lographically polished on the four sides perpendicular to the interface. Fiducial marks (deep milled slots) were made outside the diffusion zone to check on total volume change. All necessary measurements were made on a metallograph reading to +0.0005 cm. The samples were wrapped in tantalum foil and given diffusion anneals for times to 200 hr in carefully purified dry hydrogen in a sealed McDanel porcelain tube. Chromium-zirconium chips were introduced near the specimen as an additional getter. The specimens were cooled relatively slowly after the diffusion anneal to preserve the McDanel tube but no significant error in effective time at temperature was thereby introduced. At least 1 mm was ground off the surface before measurements were taken. It was observed that the grain size following short diffusion anneals was several mm and was appreciably larger in the 30 Cr alloy than in the pure Cr. No significant grain boundary penetration was present as indicated by the etch limit. The results are presented in the next section. Measurements of D were made by standard sectioning techniques with chemical analysis. Machining difficulties limited the

Jan 1, 1961

By C. H. Herty

AN earlier paper on absorption of sulfur by the slag in the basic open-hearth furnace included a brief discussion of the absorption of sulfur during the melting period. The data available at that time showed that the amount of sulfur absorbed by the melting scrap was proportional to the sulfur content of the furnace gases, and the following statement was made: "The conclusion may be drawn from these results that if a gas entirely free from sulfur were used during the melting, any iron in direct contact with the gases would be completely, or nearly completely, desulfurized before it reached the bath proper." The experimental work discussed herein deals with absorption of sulfur by the melting scrap when fuels with both high and low-sulfur content were used. Before taking up the experimental work let us consider the process as a whole as to the "flow" of sulfur. The input of sulfur occurs in: 1, the hot metal charged; 2, the scrap; 3, the stone or lime charged; 4, the ores charged; and 5, the gas. Sulfur goes out of the furnace in the steel, the slag and the gas. The distribution of sulfur in the furnace depends on the sulfur concentration in each of these materials and on the equilibrium conditions between them.

Jan 1, 1926

By J. W. Downey, A. E. Dwight, M. H. Mueller, H. Knott, R. A. Conner

Sixty new ternary equiatomic compounds are reported with a hexagonal crystal structure that is isostructural with or very similar to Fe2P, D3h-P62m. HoNiAl is a typical example, with a, = 6.9893 ± 0.0003Å, C, = 3.8204 ± 0.003Å, and c/a = 0.54 7. Three holmium atoms occupy (g): x,0,1/2 three aluminum atoms occupy (f): x,0,0; one nickel atom occupies (b): 0,0,1/2; and two nickel atoms occupy (c): 4, + , 0. The nonequivalent 1(b) and 2(c) sites give rise to two sets of unequal interatornic distances (i.e., Ho-Ni and Al-NL in the case above), which account for the prevalence of Fe2P-type tertmry compounds and the scarcity of binary examples. Unit-cell constants are presented for the sixty compounds and density measurements on the compounds HoNiAl and UFeGa confirm that three formula weights are present per unit cell. Neutron and X-ray powder diffraction intensity measurements were made on CeNiAl and HoNiAl, respectively. The atomic posiLiotml parameters in CeNiAl were determined from neutron data to be x = 0.580 5 0.001 for cerium and 0.219 5 0.001 for aluminum. An investigation of the quasibinary section between the binary compounds CeNi2 and CeA12 revealed a new ternary compound CeNiAl. The compound has a hexagonal structure and is isostructural with the prototype compound Fe2P. Additional examples discovered or confirmed in this investigation provide a total of sixty ternary compounds that are isostructural with or closely related to Fe2P. Previous investigators1'2 reported the unit-cell constants for the hexagonal compounds UFeA1, UCoAl, UIrA1, ZrNiAl, ZrNiGa, HfNiAl, and HfNiGa and the present investigation has confirmed that the compounds are isostructural with Fe2P. Independently, Steeb and petzow3 reported the same structure type for UCoAl, UIrA1, and UNiA1. However, the present results suggest a different atomic site occupancy for the component atoms in the three compounds. A detailed investigation of the relative positions of the three kinds of atoms in the compounds CeNiAl and HoNiAl will be discussed. EXPERIMENTAL PROCEDURE The equiatomic alloys were prepared from elements of 99.9+ pct purity by arc melting under a helium-argon atmosphere. After homogenization at temperatures from 700" to 900' C, a metallographic examination was performed by conventional methods, and density measurements were carried out by the immersion method in CCl4. A powder sample was prepared for diffraction studies by crushing a portion of the annealed button. X-ray diffraction patterns were obtained with a Debye-Scherrer camera, in which the annealed powder was glued to a quartz filament, and indexed with the aid of a Bunn chart. Unit-cell constants were calculated from the computer program of Mueller, Heaton, and Miller4 and d spacings were obtained by the program of Mueller, Meyer, and Simonsen.5 The intensity values were calculated from the relation I, ~ (m)(L.P.)F2 by a computer program written by Busing, Martin, and Levy.6 The absorption and temperature correction factors were neglected. An X-ray study of HoNiAl was carried out to take advantage of: large differences in atomic scattering factors for holmium and aluminum, X-ray patters free of background darkening, negligible oxidation at room temperature, and negligible weight loss in the preparation of this alloy. The neutron diffraction studies were made on a powder sample of CeNiAl contained in a -in. diam V tube and a pattern was obtained with neutrons of wavelength The neutron scattering factors employed (x 10-12 cm). In contrast to the scattering amplitude for X-rays, cesium does not have the largest cross section, however, there is a sufficient difference in the neutron scattering amplitudes to distinguish between the atomic species. The neutron transmission was high, 86 pct; therefore, absorption corrections were not necessary for the cylindrical sample. Most reflections could not be observed individually, because of the relatively large unit cell (a = 6.9756 and c = 4.0206Å) and relatively short neutron wavelength; therefore, the intensity of grouped reflections was considered. The Kennicott modification7 of the Busing-Martin-Levy program6 was employed to determine the identity of the atoms at the various lattice sites and the positional parameters. RESULTS A structure for the prototype compound Fe2P was first reported by Hendricks and Kosting;8 however, the structure was in error. The correct structure, as reported by Rundqvist and Jellinek,9 is as follows. The unit-cell constants and volumes per formula weight (V/M) are given in Table I for the sixty compounds examined in this investigation and classified as Fe2P-type compounds. The structure type was determined initially from a comparison of the unit-cell constants of HoNiAl with other known examples of this structure type1' and from the density of HoNiAl, given in Table 11. The density indicated that three formula weights comprised a unit cell, as in the prototype compound Fe2P. The assignment of the three species to lattice sites was made initially on the basis of atomic size. The large holmium atoms were assigned to the 3(g) sites that have a relatively large interatomic distance to nearest neighbor positions, the small nickel

Jan 1, 1969

By Augustus Locke

THERE are three matters related to ore-hunting which I wish especially to discuss here: first, the paucity of the special writings applying to it; second, the failure of scientists to concern them-selves importantly with it; and, third, resting on these conditions, certain possible activities for economic geologists. First, as to the writings. Geological papers. are being produced in the United States alone at the rate of 10 to 12 shelf-feet per year.1 But papers specifically for the ore-hunter would go in a slim, annual pamphlet; all that have ever been written would go in a briefcase. The art of technical ore-hunting-geology conceived as a guide to ore-has only a scant literature.

Jan 4, 1922

By J. F. Martin, J. E. Friedline, L. M. Melnick, G. E. Pellissier

A method has been developed for determining gases in steel in which the gases are extracted by vacuum fusion and analyzed by mass spectrometry. This method is especially applicable for determining small amounts of oxygen and nitrogen. The lower limit of detection for both oxygen and nitrogen is 0.0001 pct with an average deviation of about 0.0001 pct for oxygen and 0.00008 pct for nitrogen. Hydrogen analyses by this method are in good agreement with analyses by vacuum tin-fusion. A complete analysis of all gases extracted from a steel sample can be accomplished in 40 min. It has long been known that certain of the gaseous elements exert particular effects on the physical and mechanical properties of steel. With the recent advent of new experimental steelmaking practices it is now possible to obtain steels with extremely low contents of such elements as oxygen and nitrogen. Present methods for determining these two gases are of insufficient sensitivity as applied to steels made by these newer practices, and therefore a new technique was considered necessary. A review of the literature showed that the conventional vacuum-fusion method1 was the procedure most suitable for modification to obtain a sensitive method for determining the gaseous elements present in steel simultaneously. However, for trace amounts of gases it is impractical to increase the sample size because of the physical limitations of the apparatus and the increased degassing time which would be necessary. Also, when only one of the desired gases is present in trace amounts, quantitative separation by conventional vacuum fusion is almost impossible. Since small analytical mass spectrometers are now commercially available, it was decided to use this instrument in conjunction with conventional vacuum fusion for both qualitative examination and quantitative determinations of the gaseous elements in steel. This technique has already been used with success for the analysis of copper and lanthanum.2"4 APPARATUS A vacuum-fusion unit was first designed and built, Fig. 1. This unit was designed especially for the determination of small amounts of nitrogen and/or oxygen in steel since an acceptable method (vacuum tin-fusion)5 was already in use for the determination of hydrogen in steel. The vacuum system was con- structed of Pyrex glass throughout. Mercury check valves were used in place of stopcocks in the high-vacuum section of the system. Ferromagnetic samples are normally introduced into the vacuum system through a mercury lift. In case of a break in the lift, the mercury is prevented from entering the furnace by a self-locking, mercury safety check valve, Fig. 2. This check valve, developed at our laboratory, is a modified T/S ball-and-socket joint placed in the sample inlet system between the mercury and the furnace. A sudden entry of mercury or air pushes this valve into the closed position, completely blocking the top of the mercury lift. The check valve is held in the closed position by the vacuum of the apparatus. A separate entrance tube also was placed in the system, so that samples which would amalgamate with mercury, or which are nonmagnetic, could be introduced into the furnace. A slightly modified Guldner-Beach furnace is used in this system.8 The optical flat was connected to the system by a ground-glass joint to facilitate cleaning, a quartz delivery tube was substituted for Pyrex, and the crucible was used uncovered. Fusion takes place in a high-purity graphite crucible insulated by — 200-mesh high-purity graphite powder. The crucible set (crucible and funnel) is suspended in a quartz crucible. The furnace envelope and the sample inlet system are exhausted by 2 single-stage, mercury-diffusion pumps in series. The first of these is a high-speed pump, which will work only with a very low backing pressure. This pump is used to exhaust the gases from the furnace as rapidly as possible. The second mercury-diffusion pump is used as a backing pump for the first; the capacity of this pump is much lower. However, it will work efficiently against a back pressure of 3 mm of mercury. To assure positive pumping, a modified Naughton and Uhlig condenser7 is used. With the use of proper valving the second pump is also used as a circulation pump in the catalyst system.

Jan 1, 1959

By Lloyd B. Underwood

Dr. Gardener, in Chapter 2, has presented a comprehensive state-of-the- art review of site investigations For tunneling. Nearly all of the techniques he discussed will also be required for future site investigations. Therefore, this chapter will be devoted to a few rather new exploration techniques plus ideas for improving some of the present-day methods. In March 1962, the first symposium on "Remote Sensing of Environment" was held at the University of Michigan.l Since that time, four additional symposiums have been held at the same University. Also, the technical Literature has recently included a number of articles on remote sensing techniques. A recent one appeared in the February 1968 issue of Materials Research and Standards.Vt was entitled "Developments in Remote Sensing Applicable to Airborne Engineering Surveys of Soils and Rocks," and was written by Dana C. Parker. Mr. Parker predicts that aerial reconnaissance will someday supplant soil augers, rock drills, surface reconnaissance, and geophysical surveys as the engineer's primary means of obtaining information about soils and rocks. He states, "The engineer wishing to survey a route or a site or to locate rock and soils suitable for construction projects will be able to push some buttons in an airplane and record all the data required for determining the relevant conditions. In a short time after he returns to earth with his rolls of film and charts, he will be able to reduce and analyze the data by partially computerized techniques and to compile a concise and comprehensive engineering report that gives all the relevant information about rocks, soil, water, and vegetation in the area he surveyed. Most important he will feel as confident with his recommendations, derived primarily from image characteristics and spectral power distributions, as his predecessors did with recommendations based on more tangible evidence obtained from drill cores and surface reconnaissance." The airborne sensors for engineering surveys of soils and rocks are those that sample some electromagnetic property of the materials that com- prise the terrain and cover its surface. In addition to cameras, these include

Jan 1, 1970

By W. F. Boericke

NOT the least interesting sights that New York has to offer the visiting mining engineers are the extensive tunnel operations that are being pushed in connection with the subway construction. While a "hard rock" man might feel at home on these jobs, the engineers driving the subway tunnels have necessarily had to encounter some new problems pe-culiar to the largest permanent mining camp in the country. To drive a heading 36 by 18 ft. in hard rock, with a station section to follow 52 by 27 ft. across-and to do it in the midst of a city's traffic-demands engineering skill of a high order. Not the least of the problems overcome by the engineers in charge was to provide adequate ventilation for the men at the face at all times, so that there would be no delay in the work. With a crew of 40 men (32 drill runners and helpers on the machines alone, working two shifts) a hold-up due to inability to get back promptly to the face after shooting would affect costs quickly. AIR VITIATED BY EXHAUST FUMES FROM MOTOR TRUCKS A complication not encountered by metal miners, but which the subway engineers had to meet, was pollution of the air in the tunnels by fumes from the exhaust of the motor trucks used to haul away the broken rock. As shown in the cut, motor trucks were constantly em-ployed to remove the heavy tonnage broken as the tun-nels went ahead, amounting, according to R. J. Van Wagner, chief engineer of the Del Balso Construction Co., to 48 cu. yd. per ft. of tunnel advance. As the length of the tunnel under his management was 900 ft., it was essential for the safety of the men that suffi-cient air be introduced to dilute the poisonous fumes so that no ill effects would be felt for the entire distance that the trucks had to travel. The presence of the ex-haust fumes was especially noticeable on foggy days.

Jan 2, 1928

By J. D. Miller, P. J. McDonough, H. Q. Portillo

Previous investigations have demonstrated the catalytic effect of silver additions in the ferric sulfate leaching of chalcopyrite [ ] The enhanced rate of leaching was found to be due to the formation of an intermediate Ag S film which forms on the Cures2 surface by an exchange reaction Under these conditions, unlike the uncatalysed ferric sulfate leach, the elemental sulfur forms a nonprotective reaction product on the Ag S crystallites As a result, the rate appears to become limited by an intermediate electrochemical reaction in {he Ag2S film rather than by transport through the elemental sulfur reaction product [ ] The reaction rate was found to have a complex dependence on the Ag+, Fe++ and Fe+3 concentrations, but independent of the Cu concentration Electrochemical measurements with a Ag,S-coated chalcopyrite electrode provide further information regarding the nature of the reaction mechanism The kinetics of the rate limiting, intermediate electrochemical reaction are analyzed in terms of the Butler-Volmer equation

Jan 1, 1981

By J. P. Dovel

HAVING been requested to prepare a paper referring especially to my patents as applied to blast furnaces, I shall confine my discussion to those improvements and inventions pertaining directly to the blast furnace itself, omitting a number of patents pertaining to blast furnace operations. I spent the early part of my life in the construction of blast furnaces, from rivet-heating to drafting and designing, much of the work relating to repairs and rebuilding. Later, as I became more interested in maintenance and operation of a group of blast furnaces, one fact especially made a lasting impression on me, namely that a very expensive piece of equipment was very short lived, and the expense of replacement, relining, etc., in many instances consumed most of the profits made while in actual operation. As far back as 1910, I began to lay plans to build with a view to permanency and not merely for a blast, the common expression at that time, which really meant only one or two years in southern practice. Since we did not then blow so hard most failures occurred in the bosh and hearth. The failure of either generally meant a complete new lining, as the inwall did not look good enough to last another blast. At that time we were using two types of hearth, one of heavy steel plate protected by well and sprays on the outside, and .one of heavy. cast iron, made in sections and bound together with wrought-iron bands. The former type proved dangerous, for if the iron should come through, as it frequently did, it would cut away the steel plate, quickly turning large quantities of molten iron into the water, causing a severe explosion and costly repairs. The cast-iron type gave trouble also by the iron finding its way through the joints between the sections, which was' not so serious; since the iron would not cut away the heavy cast-iron sections very quickly, and generally caused only small damage, and repairs-were easily made. Both types have been improved; the former by the introduction of cast-iron -water-cooled plates, placed on the, inside of the steel, jacket. This has proved to be very good construction, but has no real claim to permanency: As the cast-iron plates cannot be replaced from the outside, therefore the operator must assume that some time, at no late date, he must replace them from the inside, which will mean a blowing out of the furnace. The heavy cast-iron hearth has been improved by making the

Jan 1, 1928

By C. G. Dunn

With respect to theories of recrystalliza-tion in metals plastically deformed. it has been said that the present status of this subject is far from satisfactory.1 It may also be said that before any mechanism of recrystallization for metals and alloys can be set forth in a satisfactory manner, there must be made available considerable data on orientation changes that occur during the deformation and recrystallization processes. Although extensive data have been published on recrystallization in single crystals and in poly-crystalline specimens, more results of a type that can be classified according to simple orientation changes would be desirable in this complex field. It might even be said that before classifications are made according to types of orientation changes, it may be possible to classify a considerable amount of data into certain kinds of orientation states if groups of common or nearly common orientation occur. Methods for computing the probability of occurrence for various types of groups have been published2 and it has been pointed out in particular that it should be possible to analyze orientation data for high-order twin relationships between old and new grains even when agreement is not at all exact. In this connection, work on recrystallization in silicon ferrite reported in a paper concerned with complex groups of annealing twins3 indicated that some data were consistent with primary nucleation OCcurring according to a second-order or a third-order twin transformation. However, further work in this latter direction was definitely needed. It is, therefore, the purpose of the present paper to report data and analyses for primary nucleation in silicon ferrite following small deformations that have been carried Out at the Pittsfield Works' Laboratory of the General Electric Co. Analyses have been made with the aid of standard groups of twins that are reported elsewhere.4 PReparation oF Specimens and Experimental Procedure The material used in the present investigation was taken from the same heat of steel as that .used in a prior report.3 The finished strip in both cases was made by the Allegheny-Ludlum Steel Corporation according to methods that produce a high degree of preferred crystal orientation. Samples with large grains had the following composition: 3.45 per cent Si, 0.003 C, 0.008 P, 0.020 S, 0,075 Mn, 0.03I A1 and 0.072 Cu. Thickness of specimens was 0.012 inches. Plastic deformation was produced by cold-rolling the samples on a mill with 8-in. diameter rolls, the plane of the sample in each case coinciding with an XY plane (the plane of projection for the stereo-graphic plots) and the elongation occurring in the X direction. In general, elongations were held to about 3 or 4 per cent.

Jan 1, 1945

By G. R. Speich

A cellular precipitation reaction in which cells consisting of an Ni3Ti (DO24) phase and austenite are formed has been studied in an austenitic Fe-30 Ni-6 Ti alloy. The variation of the growth rate and interlamellar spacing of the Ni3Ti cells with temperature has been determined m the range 400" to 975°C; the interlamellar spacing is proportional to the degree of undercooling; the growth rate can be expressed by an equation of the form G = K?T)2 exp(-Q/RT). The habit of the Ni3Ti lamellae is (001)Ni3Ti (111)y;[010]Ni3T2 [010]y. An almost perfectly coherent interface is formed between Ni3Ti lamellae with this orientation rela -tionship and the intervening austenite. This first Ni3Ti cellular product is subsequently consumed by a second cellular reaction of much coarser spacing. CELLULAR precipitation reactions have been studied in copper-base,1,2 Au-Ni,3 pb-sn,4 and iron-base ferritic5,6 solid solutions, and this mode of precipitation has been treated theoretically by smith," Turnbull,8,9 cahn,10 and more recently by bohm.11 In the case of substitutional austenitic iron-base alloys little or no data are available, Cellular precipitation reactions are well known in austenitic nickel-base alloys12,13 but usually these reactions do not proceed to completion because of general precipitation occurring in the matrix, and they have not been studied in detail. Precipitation from an austenitic Fe-30 Ni-6 Ti alloy was studied as part of a larger investigation of the mechanisms of precipitation from substitutional iron-base alloys. This alloy, austenitic at high temperatures, decomposes at lower temperatures by a double cellular precipitation reaction. The first decomposition product consists of alternate lamellae of an Ni3Ti(DO24) phase and austenite. The reaction proceeds to completion, consuming all of the original austenite. This first cellular product is subsequently consumed by a second cellular reaction of much coarser spacing. The first cellular reaction was studied in detail by light and electron microscopy, hardness measurements, and by X-ray and electron diffraction. Interlamellar spacings and growth rates were measured during isothermal aging in the range 400" to 975°C. The orientation relationship between the Ni3Ti and austenite lamellae was determined and indicates that an almost perfectly coherent interface exists between the two phases. This first Ni3Ti cellular reaction is of particular interest because it occurs over such a wide temperature interval. This allows cellular growth rates and interlamellar spacing data to be obtained for much larger degrees of undercooling than reported hitherto. MATERIALS AND EXPERIMENTAL PROCEDURE The Fe-30 Ni-6 Ti alloy was prepared from electrolytic iron, Mond nickel shot, and sponge-purity titanium* by vacuum melting in a zirconia crucible

Jan 1, 1963

By C. M. Wayman, R. Bullough

The selection rules fir twinning in fcc, bcc, and hcp lattices as established in Part I are used to predict the positions, relative to the matrix (untwinned) reciprocal lattice, of reflections due to double diffraction from the twins. These doubly diffracted reciprocal lattice points, which often coincide with ordinary matrix reciprocal lattice points, are deduced from kinematical considerations. 1. INTRODUCTION. A Bragg diffracted beam under certain conditions may be rediffracted to produce a third beam i .e., the incident beam, the first diffracted beam, and the rediffracted beam). In such a case an initial incident beam is diffracted by a set of planes; the diffracted beam may then be rediffracted by a second set of crystallographically different planes. The initially diffracted beam acts as an incident beam for the second set of planes, thus resulting in a twice-diffracted beam. This twice-diffracted beam may be regarded as a singly diffracted beam from a set of lattice planes whose structure factor is zero. In order to find the reciprocal lattice point corresponding to the doubly diffracted beam, it is customary1,2 to combine vectorially the component reciprocal lattice vectors which head to the extra reflections. For example, hcp metals may exhibit the forbidden (0001) reflections.* As Fig. 1 shows, the (0001) reciprocal lattice point results from: (1010) + (1011) = (0001) Similarly, combination of the beams (1011) and (1010) gives rise to: (1011)- (1010) = (0001) As Pashley and stowell2 have pointed out, even if in fact the double diffraction points lie on the Ewald sphere, they may not actually represent observed doubly diffracted beams because the initially diffracted primary beam, i.e., the source, must also correspond to a reciprocal lattice point which lies on the sphere of reflection; however, the reciprocal lattice point corresponding to the planes causing the rediffraction need not lie on the sphere. A little consideration of the Ewald construction in Fig. 2 makes this argument clear. In Fig. 2 the incident beam is represented by the wave vector ko. This beam is initially diffracted by the lattice planes (hkl) which are represented by the reciprocal lattice vector r(hk1) The reciprocal lattice point (hkl) of course lies on the Ewald sphere in order that the Bragg condition be satisfied. The initially diffracted beam is represented by the wave vector kl. If now kl is rediffracted by a second set of planes (h'k'l') resulting in k2 the lattice point (h"k"l") must lie on the Ewald sphere if the double diffracted beam k2 is to be observed. It is clear that (h"k"l") is the vector sum of (hkl) and (h'k'l'), and that (h'k'l') need not in fact lie on the Ewald sphere. In the usual1,2 analysis the origin (000) of the reciprocal lattice is shifted to the point (hkl). However the translation (000)— (hkl) automatically shifts the point (h'k'l') to the Ewald sphere, i.e., (h'k'l')— (h"k"1"). It is to be seen that (hkl), the source reflection, must lie on the Ewald sphere; if it does not the translation (000) — (hkl) places the "new" origin off the sphere, not satisfying the Ewald construction and hence the Bragg condition. The point (h"k"1") of course must lie on the sphere if it corresponds to an observed doubly diffracted beam. It is to be noted that crystals having the hcp structure, as just discussed, are intrinsically capable (i.e., without lattice defects such as twins) of double diffraction, as contrasted to fcc and bcc crystals which are extrinsically capable (requiring lattice defects or reoriented lattice regions). The "allowed" bcc reciprocal lattice points (which comprise an fcc lattice) are (110), (2001, (211), (220), (310), (2221, (321), (4001, and so forth. The combination

Jan 1, 1967

By W. H. Emmons

ALTHOUGH gold is one of the rarer metals, it is widely distributed; it is found on all of the continents and in each of the grand metallogenic provinces of the earth. It is prominent particularly in the shield areas of the earth; these areas have produced a large part of the world's lode gold and in most of them gold lodes are more important than the lodes of other metals. The Scandinavian shield is the only one that has not produced much gold. Nearly all of the world's gold has been derived from lodes and from sands and gravels where gold placers formed by the destruction of lodes. The gold derived from magmatic segregations, from pegmatites and from contact metamorphic deposits is quite subordinate to that derived from auriferous lodes. The lodes include all veins and related deposits that are formed by hot waters that move along fissures or other openings and that deposit vein matter in the fissures and by replacement of the country rocks along the fissures. All of the shield areas of the earth are characterized by large areas of granitic rocks including granitic gneisses, granodiorites and other acid intrusives which here are included in the general term "granite." The granites are intruded into schists, ancient lavas and other rocks which here are designated as the "invaded" rocks. The granites are parts of what once were great batholiths: that is, they are the remaining portions of great deep-seated bodies that slope outward, have very irregular roofs and so far as known have no floors but extend downward to great though unknown depths. Some of them are scores or hundreds of miles across and contain islands or "roof pendants" of the invaded rocks at places where the roofs of the batholiths were low-that is, where erosion has not yet completely unroofed the batholiths.

Jan 1, 1932

By R. B. G. Yeo

Pronounced isothermal martensite formation at room temperature was measured dilatometrically in a steel containing 0.01 pct C, 24.9 pct Ni, 0.26 pctAl, 2.58 pct Ti and 0.25 pct Cb. It is shown that martensite will form isothermally if stabilization of the austenite-martensite transformation is eliminated by removal of carbon. The decarburization of two iron-nickel alloys allows isothermal transformation to martensite to occur at temperatures above their athermal Ms temperatures. In an Fe-22.4 pct Ni alloy, at the 0.008 pct C level, the Ms temperature during air cooling is 85°F higher than that during- water quenching-. At the 0.15 pct C level this difference is reduced to only 5°F. The introduction of carbon causes stabilization during air cooling which lowers the Ms temperature virtually to the same level as determined during mate?. quenching. Thus in the 0.15 pct C alloy, the Ms temperature is almost independent of cooling rate. It is suggested that rival theories of martensite formation should be reexamined in alloys of sufficiently low carbon and nitrogen content to eliminate the complication of stabilization. The Ms temperature of a steel containing 0.01 pct C, 24.9 pct Ni, 0.26 pct Al, 1.58 pct Ti and 0.15 pct Cb, solution treated at 1500°F and air cooled as 1/8-in. diam specimens, was found to be 57 °F. 1 However, when held for several hours at room temperature the steel hardened slightly and became appreciably ferromagnetic. Isothermal transformation to martensite was first revealed by Kurdjumov and Maksimova2 in an iron-base alloy containing 0.6 pct C, 6.0 pct Mn and 2 pct Cu. Most of the other studies of isothermal martensite have also been confined to highly alloyed steels which transform at subzero temperatures; for instance, DasGupta and Lement, 3 Cech and Hollomon, 4 Machlin and Cohen,5 Shih, Averbach, and Cohen.6 Averbach and cohen7 noted a rapidly decaying volume increase at room temperature in a steel containing 1 pct C, 1.5 pct Cr and 0.2 pct V. cina8 and Marshall, Perry, and Harpster9 have described the isothermal transformation to martensite at room and subzero temperature in stainless steels. Kurdjumov10 has recently reviewed the subject, noting that the isothermal formation of martensite can be observed only in the temperature range somewhat below Ms or below -50°C. The isothermal formation of martensite may be characterized as follows: 1) It occurs in steels of widely different compositions, the main prerequisite being a low transformation temperature. 2) The transformation occurs by the formation of new plates and not by the growth of old ones. 3) The isothermal transformation is suppresed by stabilization during slow cooling or holding at temperatures near room temperature. However, the factors governing this mode of transformation are still not fully understood. The formation of martensite isothermally suggests an activated process. The early theories of martensite formation did, in fact, utilize classical nucleation concepts. Kurdjumov 11 first proposed the presence of thermally activated nuclei of different sizes and compositions which would grow if they reached critical size during cooling. This treatment was enlarged and developed quantitatively by Fisher, Holloman, and Turnbull12,13 and was later reviewed by the latter two authors.14 Fisher15 associates Ms with a nucleation rate of one per cc per sec. At slightly higher temperatures the nucleation rate is so low that isothermal formation of martensite is not observed in reasonable times. At slightly lower temperatures the nucleation rate is so high that it could not be suppressed by rapid cooling. By judicious use of parameters Fisher 16 was able to obtain good agreement between classical nucleation theory and the incubation times of martensite formation.4 However the application of these principles to martensite formation in iron-nickel alloys15 predicts that an alloy containing about 30 pct (31 at. pet) Ni would not transform. The presence of an Ms temperature at -223° C in an alloy containing 34.1 pct (33 at. pct) Ni led Kaufman and cohen17 to reject the hypothesis of homogeneous nucleation in favor of the reaction path theory originally proposed by Cohen, Machlin and Paranjpe.18 This theory conveniently explains the formation of martensite athermally but becomes labored when dealing with isothermal formation. Kaufman and cohen19 did explain the isothermal activation of embryos by assuming it to be a result of the expansion of their boundary dislocation loops but this treatment predicts an upper temperature limit of isothermal martensite formation.

Jan 1, 1962

By Persifor Frazer

The mines which I am about to describe are all situated in the northern part of the States of Nuevo Leon and Coahuila, Mexico, between the twenty-sixth and twenty-seventh degrees of latitude. They might be grouped, orographically, into four classes: 1. Those in the Sierra de la Ygnana chain; 2. Those in the Sierra de Gomez chain; 3. Those in the Cerro Mercado; 4. Those in the Sierra de San Marcos chain. (See large map.) The first two of these may be further arranged in one geographical district, to which the name, "the Villaldatna. district," may be applied, and the last may be ascribed to the geographical district of " Monclova." Geologically described, the country rock, in which four of the six mines occnr, is a limestone, concerning which a few words will be said further on, to wit.: The Arroyo (gulch), the Montanos and the Pinitos (pines), in the Villaldama district, and La Paloma (the dove), or Iron Mine, in the Monclova district. The San Rafael appears to lie in granite, or a heavy-bedded gneiss, presenting most of the characteristics of the latter, though the contact plane of the limestone is not far off. It is certainly worthy of attention that the ore occurs in that portion of the crystalline rock, which is nearest to the limestone, and it has been thought by some observers to be a true contact vein. It is well known that veins of this character are very often distinguished for constancy and richness. Although the undersigned cannot entirely free himself from the impression that this proximity of different formations has had an important influence in the origin of the part of the vein on which this mine is situated; still he was unable to establish it actually at the contact of the limestone and granite, but rather a short distance within the latter. Two openings of the Riojas vein were respectively in limestone and in rotten whitish granite, but this fact, if established (as by the correspondence of the strike line of the vein in direction with that of a line joining the

Jan 1, 1884

By L. W. Eastwood

THE recrystallization and grain-growth phenomena of cold-worked metals have considerable industrial importance because of their role in the fabrication of metals. For this reason, and because of the general academic interest in the subject, these processes have received consider-able attention since the time of J. E. Stead's paper1 on The Crystalline Structure of Iron and Steel. There are considerable differences of opinion regarding the theory of recrystallization and grain growth and also differences in the observation of the modus operandi of the processes themselves. The value of many of the existing quantitative data on grain growth is decreased by the failure to distinguish between the grain sizes just after complete recrystallization and those resulting from coales-cence. For this reason also, the value of the diagrams of stable grain sizes, like those produced by Bass and Glocker2 and Czochralski3, is lessened in so far as an interpretation of the facts of recrystallization is concerned. It is hoped that the data presented in this paper will help to clarify and to simplify the facts relating to recrystallization, and at the same time will show that some of the present-day conceptions are unten-able. A paper on the theory of recrystallization, with additional data, will be completed in the near future by the writers.

Jan 1, 1935