Search Documents

By Enrique Touceda

As in the case of steel and the non-ferrous alloys in general, the use of the microscope in connection with the manufacture of malleable cast iron has proved of inestimable value to the industry. Had its use not been invoked, many facts either would not be known at all or, if suspected, would be confined to the realms of conjecture. No fairer statement could be made than that the start of real progress in the industry was coincident with the application of metallography to the product, though the full significance of this statement can hardly be appreciated except by those who not only are conversant with conditions as they existed at the time referred to, but are familiar with the character of works' practice at the present time.. A few years ago, about the only test made to ascertain the physical properties of the product, except in the case of certain plants, was the bending of a casting to destruction, not only with the object of discovering whether or not the metal was ductile, but for the purpose of inspecting the fracture. The characteristics of the fracture, if correctly interpreted, were known to be of value in locating the trouble in castings that were inferior. In general, it was found that if a casting of medium or heavy section would bend through a wide angle before failure took place, the fracture in the majority of cases would have a black velvety appearance; while if it was held at different angles to the direction of the rays of light, it would show a change of color and an iridescent sheen. But an inferior air-furnace heat or anneal might yield castings which, if thin and consequently largely decarburized, could be bent double on themselves and still not possess the fracture described. If, on the other hand, a casting broke short, its fracture might have one of a great many different color and structural peculiarities. Depending on the cause of the trouble, such castings might have any of the fracture characteristics, of which the following is but a partial list.

Jan 1, 1922

By V. L. Minear

This paper presents some of the problems encountered and solved by the construction industry during recent years while pressure grouting the foundation rock of dams. Pressure grouting has become "Standard Operational Procedure" and consequently many hundreds of thousands of bags of cement have been used for that purpose. There is nothing weird, mystical, or even particularly difficult about the basic idea. Holes are drilled in the rock and grout is pumped into them. This procedure is used to shut off the flow of water under the dam and to reduce the uplift on the dam. Like most other engineering and construction problems, the fundamental principle is simplicity itself, but some of the "minor details" are rather complex. When faced with the problem of actually forcing the grout into the rock, or keeping it there once it has been injected, an engineer frequently has need for all of the ingenuity and initiative that he has at his disposal. It is proposed to discuss these minor details at length, even at the risk of boring the reader. The difference between success and failure in a grouting program can well hinge upon some such detail that may not be fully understood. Pressure grouting is a method used to make good foundations from bad ones by plugging actual or potential passages within the rock through which water might escape and thereby diminish or even destroy the usefulness of the dam. In some special cases, pressure grouting has been used for the purpose of consolidating broken rock to increase its bearing power. Lacking this useful method, many of the dams constructed during recent years could not have been built. Most of the really excellent dam sites in this country have been utilized long ago. Consequently it becomes necessary to find methods of utilizing the less desirable sites. Pressure grouting plays a vital role in the methods developed. Engineers have learned the hard way, that the term "solid rock" is a misnomer. Solid rock does not exist to any considerable extent in nature. Practically all rock contains imperfections such as shrinkage cracks, bedding planes, joints, solution channels, folds, shear zones, crush zones, and the like. All these imperfections are weaknesses through which ground water is likely to flow. The function of rock grouting is to rectify these imperfections and make the rock as nearly "solid" as practicable. The location, direction, depth and number of grout holes to be drilled are important. Clearly, a hole must pierce fractures in order to serve a useful purpose, for grout cannot be forced into the rock itself. Were it possible to determine the pattern and extent of the cracks within the rock, it might be feasible to drill two or three strategically placed holes so as to make practicable the grouting of the whole integrated network of cracks from them. Such is not the case. While a study of the geology, surface indications, and drill cores is helpful in gaining an idea of subsurface conditions, in the final analysis, the seams must be located by trial and error methods. There can be no doubt that the closer the

Jan 1, 1949

By S. K. Nowak

The lithium solubility limit in solid aluminum was determined by the use of micro-graphic techniques. The solubility limit thus established was shown to be a true equilibrium by checking the reversibility of AlLi phase precipitation and dissolution around the equilibrium temperature. The experimental results fit a straight line by plotting log N(LI) against 1/T. The metallurgical reasons explaining the lack of agreement among previous investigations are discussed. THE solubility limit of lithium in solid aluminum was determined by Shamray and Saldau1 by micrography and by Grube et al.' and also Voss-Kiihler- by measurement of electrical resistivity. Since the addition of lithium induces extremely small changes in the aluminum lattice, X-ray techniques could not be employed for this purpose; in fact, the addition of lithium does not cause an expansion of the lattice as might be expected from a consideration of atomic radii, but causes a small contraction from 4.040 to 4.037A3, 4 when the solvent aluminum is saturated with this element. An analysis of the results from previous investiga-tions'" shows that with improvement of investigation techniques the solubility limit tends toward a lower lithium content. Again, some of the author's own experimental results on the action of atomic hydrogen on A1-Li alloys seemed to indicate that the solubility of lithium should be much lower, i.e., about 0.3 pet at 300°C: instead of 1.15 pet, the lowest published value.4 For the foregoing reasons it was decided to investigate this problem. The aluminum and the lithium used for this purpose were of the highest purity. The lithium solubility limit was determined by metallographic techniques, in particular by the use of a reagent especially developed for the purpose of revealing the AlLi phase. The solubility limit thus determined was shown to be a true equilibrium by checking the reversibility of AlLi phase dissolution and precipitation around the equilibrium temperature. All of the experimental work was carried out in 1951 at the Centre d'Etudes de Chimie Metallur-gique at Vitry, France, under the direction of Georges Chaudron.

Jan 1, 1957

By H. Van F. Furman

As the cyanide-method for the extraction of gold from ores is extensively used in the United States and elsewhere, and appears destined to prove a factor of increasing importance in the metallurgy of gold, a description of the latest laboratorymethods may prove of interest. The history of the development of the process in the United States has been analogous to that of all new processes. Many failures are to be recorded and a few successes. It is the opinion of the writer that, had the following simple tests been better understood, many of the failures would not have occurred, and we should probably have a larger number of successful plants in operation. While the process is not simple, but requires a high degree of chemical and engineering skill, the determination of the adaptability of an ore to the method is generally not difficult. While the laboratory-results will not always coincide with the actual results obtained in the mill, they will serve as a guide and control on the working of the mill, and mill generally suffice to determine if the ore can be

Jan 1, 1897

By John M. Dealy, Robert D. Pehlke

This note presents a summary of the available literature on activity coefficients at infinite dilution in binary metallic solutions, Table I. These data should prove useful in not only examining the therm-odynamic properties of binary metallic solutions, but also in predicting the activity of a component in a complex alloy. The relationship proposed by wagner1 for expressing the activity coefficient in dilute solution is of the form:

Jan 1, 1963

By D. V. Carter, F. M. Hackbusch

Beginning the year 1938, the East and East Central Texas district comprised 48 counties, which is equivalent to the Texas Railroad Commission districts 5 and 6. At the close of the year there were 46 oil and gas fields in this district. Eight other fields, seven oil and one gas, have been abandoned. Exploratory Drilling During the year, 113 exploratory wells were drilled. Nine discoveries were made, five of which proved to be oil fields, three distillate, and one gas. Completions for the district were 2043 oil wells (distillate wells included), 36 gas wells and 163 dry holes. Exclusive of the East Texas field, the Marion County extension of the Rodessa field led the district in the number of completions during the year. Production and Proration All fields in the district produced a total of 182,369,484 bbl. of oil, a decrease of 12.57 per cent compared with the 208,594,453 bbl. produced during 1937. The East Texas field produced 148,189,913 bbl., which was 81.6 per cent of the district's production for 1938. November daily average oil production for the East and East Central district was 469,102 bbl. The estimated cumulative production to Jan. 1, 1939, for this district was 1,753,894,802 bbl. It is estimated that the East and East Central district produced 38.9 per cent of the state's total production for the year, which was 468,781,632 barrels. The decrease in 1938 production, as compared to that of 1937, in this district was partly due to the Saturday and Sunday shutdowns, 71 days for the year, which is equivalent to 19.45 per cent of the year. All fields in this district were affected by shutdowns except the Texas portion of the Rodessa field, which was shut in only during January and February. Certain wells were exempt from these shutdowns because of special pro-

Jan 1, 1939

By D. V. Carter, F. M. Hackbusch

Beginning the year 1938, the East and East Central Texas district comprised 48 counties, which is equivalent to the Texas Railroad Commission districts 5 and 6. At the close of the year there were 46 oil and gas fields in this district. Eight other fields, seven oil and one gas, have been abandoned. Exploratory Drilling During the year, 113 exploratory wells were drilled. Nine discoveries were made, five of which proved to be oil fields, three distillate, and one gas. Completions for the district were 2043 oil wells (distillate wells included), 36 gas wells and 163 dry holes. Exclusive of the East Texas field, the Marion County extension of the Rodessa field led the district in the number of completions during the year. Production and Proration All fields in the district produced a total of 182,369,484 bbl. of oil, a decrease of 12.57 per cent compared with the 208,594,453 bbl. produced during 1937. The East Texas field produced 148,189,913 bbl., which was 81.6 per cent of the district's production for 1938. November daily average oil production for the East and East Central district was 469,102 bbl. The estimated cumulative production to Jan. 1, 1939, for this district was 1,753,894,802 bbl. It is estimated that the East and East Central district produced 38.9 per cent of the state's total production for the year, which was 468,781,632 barrels. The decrease in 1938 production, as compared to that of 1937, in this district was partly due to the Saturday and Sunday shutdowns, 71 days for the year, which is equivalent to 19.45 per cent of the year. All fields in this district were affected by shutdowns except the Texas portion of the Rodessa field, which was shut in only during January and February. Certain wells were exempt from these shutdowns because of special pro-

Jan 1, 1939

By E. A. Gulbransen, J. W. Hickman

ONE of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film A comprehensive program has been undertaken to study these phenomena This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C Before the introduction of the electron diffraction technique, it «as necessary to use either direct chemical analyses or X-ray diffraction analyses to determine the nature of the oxide film formed on the metal or alloy Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry In special cases the information obtained may be identical, but in general both view-points are necessary Much of, the early work was carried out on the oxidation of bulk samples where thick films were obtained The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses Although much useful information has been obtained in this manner, little could be learned about the character of the protective oxides during the period when the films were actually protective Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective LITERATURE The oxidation of iron has been extensively investigated by X-ray and electron diffraction Jackson and Quarrell1 found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe304, between 515° and 900°C the stable film was FeO Above the upper change point of iron the oxide was found to be Fe304 prom 400° to 515°C , FeO, Fe304 or a mixture of the two oxides was found Recrystallization of the air-formed film below 400° and above 900°C led to the formation of Fe304 In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described

Jan 1, 1946

By B. S. Hickman

Using primarily quantitative single crystal X-ray techniques studies have been made of the precipitation of the metastable w phase in alloys of titanium with Mo, Mn, Fe, Cr, and Nb. It is shown that, in agreement with earlier work on the Ti-V system, the composition of the w phase during aging approaches a constant; the value varies from one system to another in a systematic manner with the electron concentmtion. Results relevant to the mechanism of w precipitation during quenching and during aging are presented and discussed. Results are presented to confirm that the w phase is coherent and the nzorphology of the Necipitates is described and discussed. PRECIPITATION of the metastable w phase in alloys of titanium is of interest because of its severe embrittling effect and also because of the enhancement of the superconducting properties which accompanies precipitation.1 The general features of w phase precipitation have been discussed by cuillan and by Bagaratskii et d3 The work described in this paper forms part of a general study of w phase precipitation which was undertaken to elucidate various unknown or controversial features of the process, namely: i) What is the mechanism of formation of the phase ii) How does its composition, morphology, volume fraction, and particle size vary with the type and content of the alloying element and with the heat treatment conditions? iii) What is the relation between the w phase and the equilibrium a phase? In a previous paper4 the results of a detailed study of w phase in Ti-V alloys were presented. It was shown that: U During aging the composition of the w phase approached a saturation value of 13.5 to 14.0 at. pct V. ii) w precipitated as cube shaped particles and once precipitation was complete, particle coarsening did not occur. iii) a phase formed initially by direct conversion of w-phase precipitates. In this paper similar measurements are reported on Ti-Mo alloys and some more limited data given on the Ti-Cr, Ti-Fe, Ti-Mn, and Ti-Nb systems. The results i.1 the six systems are then compared. It has been shown previously by electron microscopy that the w precipitates as ellipsoids in both the Ti-Nb system,&apos; and in i-o.&apos; Blackburn and williamsz3 have reported the precipitates in Ti-Fe, Ti-Cr, and Ti-Mn are cubic, i.e., similar to the Ti-V system.476 EXPERIMENTAL METHODS 1) Specimen Preparation. Samples of the compositions shown in Table I were prepared by arc melting. High purity electron beam zone refined titanium (Materials Research Corporation Grade I—total impurity content =250 ppm) was used; the other source materials are given in the table. A commercial Ti-8 wt pct Mn alloy was used for studies of this system. After homogenization the materials were rolled or cut into strip approximately 1/4 in. by 2 in.; the strip was then heated at temperatures of 1200" to 1300°C for several hours by passage of a direct current through the strip in an ultra high vacuum system (<10-torr) and then quenched by admitting high purity helium and switching off the current. This treatment resulted in crystals up to 2 in. by 2 in. by A in., almost all of which had a [100] direction nearly perpendicular to the plane of the strip. The crystals were cut from the strip by spark machining and their composition checked by lattice parameter measurements supported by chemical analysis. 2) X-Ray Diffraction Methods. Lattice parameter measurements were made using a modification of the single crystal spectrometer described by ond. In this technique the crystal angles for reflection on either side of a highly collimated primary beam are measured. Generally the 400 CuK, or the 400 CuKp reflections of the bcc lattice were used. In the as-quenched crystals a precision of 1 in 105 was obtained, but due to line broadening the parameters in aged materials could only be measured to 1 in lo4. This accuracy was, however, quite adequate for the purposes of these experiments and enabled the composition of the p phase to be obtained to 10.1 pct in all systems except Ti-Nb where the lattice parameter change with composition is very small. The precipitation and growth of the w phase was examined using a single crystal goniometer attached to a Phillips diffractometer. The relative intensities and line shapes of b-phase and w-phase reflections

Jan 1, 1970

By C. E. Birchenall, J. R. Stubbles

ThE equilibrium between lead, lead sulfide (PbS), and atmospheres of H2 and H2S has been determined previously by Jellinek and Deubel,&apos; and SudO.&apos; Blbem and Kroger3,4 used Jellinek&apos;s data to calculate the sulfur dissociation pressures of PbS crystals (of

Jan 1, 1960

By C. H. Gerould

I would like to take a moment to consider our polystyrene-silica replica technique, which was developed at the Dow Chemical Co. and which was mentioned in the paper just given by Mr. Thielsch. He stated that he feared that our replica technique would cause difficulty due to deformation of the metal as a result of the application of pressure during the molding process. We at the Dow have never had any reason to suspect that any deformation of the metal was occurring during the molding process. Our procedure has been to heat the polystyrene to a temperature of 160°C. before applying any pressure, at which temperature the polystyrene is a viscous liquid. By so doing the pressure of the polystyrene against the metal is essentially hydraulic and is therefore applied equally in all directions, which we feel should not cause deformation. Our work using this replica technique has brought forth several indications that deformation of the specimen is negligible. These indications are: I. Direct comparisons have been made between the light and electron microscopes when studying a specific spot on a metal surface. These "same spot" studies were obtained by first taking micrographs at high magnification, with a light microscope, of a specific structure that could be readily recog-

Jan 1, 1947

By E. W. Davis

Iron-ORE beneficiation methods are determined largely by blastfurnace requirements. There are still many millions of tons of direct furnace ore in the Lake Superior district and blast furnaces are designed and operated for the most efficient use of this material. Beneficiated ore must be so prepared that existing furnaces may use it without alteration in design or radical changes in practice. Many attempts have been made to develop new furnaces or processes for smelting iron-ore concentrate not suitable for blast-furnace use, but these processes have gained little importance. It is, therefore, the endeavor in beneficiating iron ore to make a product that will give at least as good results as direct furnace ore in existing blast furnaces. The term "beneficiation," as applied to iron ore, does not necessarily mean concentration, but more accurately means "dressing up" the ore so that it is more acceptable to the blastfurnace operators. In modern blast-furnace practice the structure of the ore is quite as important as the chemical analysis. Certainly, the higher the iron content and the lower the silica, phosphorus and sulfur, the more desirable the ore bccomcs; but if the structure is bad, that is, if the blast-furnace gases can penetrate the charge only with difficulty, the ore is undesirable regardless of its analysis. This means that the ore should be as uniform in size as possible and free from fines, and also that the individual particles of ore should be pervious to the reducing gases of the furnace. Structure and purity are the primary requirements for a furnace ore and structure is just as important as purity. Iron-ore beneficiation processes can be divided, therefore, roughly into two main classifications: (1) processes that primarily improve the structure, and (2) processes that primarily improve the chemical analysis. During the past 10 years approximately 25 per cent of the ore shipped from the Lake Superior district has been beneficiated. Of this about half has been crushed and screened, a simple operation that primarily improves the structure but in some cases also improves the analysis slightly. The other half of the shipment of beneficiated ore, amounting to an average

Jan 1, 1935

By W. J. Rooney, James Fisher, W. O. Hotchkiss

During the summer of 1927, the Department of Terrestrial Magnetism of the Carnegie Institution of Washington joined with the Michigan College of Mining and Technology in conducting a series of earth-resistivity measurements in the Michigan copper country. The geological structure in this section is quite varied and fairly well known. The purpose of the investigation was to discover the correlation between the variations in electrical resistivity of large masses of soil and rock in place and the geological structure below the surface. The work done may be roughly divided into two parts: (1) Measurement and study of the variations in resistivity with depth, or with volume, to establish such general relations as exist between the two; and (2) the determination of the specific resistivity of various formations in order to make available more fundamental data which may aid in the interpretation of the results of the former type of measurement. A report by Mr. Rooney, which gives in detail the measurements made and the results obtained, forms the basis for this article. Measurement and Study of Variations in Resistivity The possibility of applying data from measurements of the physical properties of earth material to the study of the geological structure has long been recognized, and a number of methods for determining the position and character of concealed rock strata by means of seismic, gravitation, magnetic and electrical measurements made on the surface are being used with varying degrees of success. One physical property which varies widely for different materials, and hence affords an opportunity for distinguishing between them, is their electrical resistance. Locations • were selected where the geological structures were well known and where the depths to the water level and bed rock had been determined by drilling. The problem was to determine the value of measurements of resistivity and its variations as indications of the geological structure below the surface.

Jan 1, 1929

By A. L. Field, P. H. Royster

The first report on the slag viscosity work of the Bureau of Mines was made by one of the authors1 in 1916. It was concerned chiefly with the method of measurement. A paper2 on this phase of the work was presented to the Institute in February, 1917, and a similar paper3 was communicated to the Faraday Society. PuRpose and Scope of the Slag Viscosity Tables Following the development of a suitable method, the next step in the investigation was the measurement of slag viscosity over a wide range of temperature and composition, and the arrangement of this experimental data in the form of tables for the use of the blast-furnace operator. It is believed that this information, if used intelligently, should help the operator to reduce losses in production caused by off-grade pig iron, to improve fuel economy, to promote operating efficiency, and to extend present-day practice to meet the increasing need of smelting lean and complex ores. In the experimental part of the work it was carly, observed that the temperature-viscosity relations of a slag were determined, for practical purposes, by the relative proportions of the three major constituents, lime (CaO), alumina (Al2O3), and silica (SiO2), provided the percentage

Jan 1, 1918

By C. E. Feltner

In a recent note, Meleka and Hiarris1 have reported that the application of a constant strain rate Ad a superimposed cyclic stress to 99.99 pct polycrystal-line zinc at room temperature produced some marked effects in the resultant behavior. In their work, one end of the specimen was pulled in tension at a constant strain rate while the other end was subjected to a sinusoidally varying load (20 cps) of constant amplitude. For the slower strain rates and the larger superimposed cyclic loads, it was observed that the specimen could withstand strains prior to failure more than 100 pct greater than the fracture strains obtainable in simple unidirectional straining. This ductility effect was interpreted as being due to a cyclic stress enhanced thermal recovery process. It is the purpose of the present note to describe some related effects in 99.99 pct polycrystalline cadmium. Specimens were loaded in repeated tension at room temperature with a stress of sufficient magnitude to cause failure in about 1000 cycles and the accumulated strain was measured as a function of cycles and time. In addition, some specimens were subjected to a steady creep stress equal in magnitude to the peak value of the cyclic tensile stress. The resultant strain-cycle and strain-time curves for both types of test are shown in Fig. 1. It should be noted that the static creep specimen failed in about one third the time required to produce a cyclic failure but in the cyclic test the specimen was able to withstand a uniform strain before necking more than 50 pct greater than that possible

Jan 1, 1963

By S. Andrew Kulin, L. Kaufman

A general treatment of the broadening of X-ray double-crystal spectrometer rocking curves due to distributions of tilts and strains has been carried out. The results of this treatment have been applied to the case where dislocations in a crystal give rise to both tilts and strains. On this basis it is found that the rocking-curve halfwidth due to imperfections in the crystal, ßC , increases with increasing Bragg angle, 8. These considerations predict linear relationships between & and tan2 , and ßCand tan 8, for Gaussian and Cauchy distributions of dislocations, respectively. The zero intercept of the ßC us 8 curve, which is a measure of the degree of imperfection of the crystal, is found to depend directly on the distribution rather than the number of dislocations. In addition, the slope-intercept ratio for the ßc - ? curve has been calculated for both the Gaussian and Cauchy distributions. Experimental determination of the - 8 curves for a series of copper single crystals prepared by the Bridgeman and Czochralski methods yields results in agreement with the calculated slope-intercept ratio for a Cauchy distribution of dislocations. CERTAIN X-ray techniques have been used to study the perfection of single crystals. Gay, Hirsch, and Kelly have considered the spreading of spots into arcs on Debye-Sherrer rings due to imperfections. The Double-Crystal Spectrometer has also been applied to this problem.2 The characteristics of Double-Crystal Spectrometer Rocking Curves have been described in the literature by various workers.2-4 By assuming a random spacing of dislocations which give rise to a Gaussian distribution of misorientations relative to some mean orientation in a crystal Gay, et al.,1 arrive at the conclu- sion that the most probable misorientation is given by where h is the spacing between dislocations, and 8 and are the relative misorientations of neighboring regions. If ßC is the halfwidth of the rocking curve (the width at one-half the peak intensity) due to dislocations in the crystal then5

Jan 1, 1960

By J. D. Sullivan, Chester R. Austin, J. L. Nunes

It is characteristic of most shales and surface clays that a bloated or vesicular structure is produced by burning to a sufficiently high temperature, usually about 150° to 200°F. above the normal maturing temperature used when making common brick of the same material. Early investi-: gators recognized this phenomenon and attributed it to the release or expansion of gases in the vitrified piece. A number of theories have been advanced on the source of the gas and the manner in which it is evolved, but none has been proved conclusively. T. E. Jackson&apos;s1 early theory that bloating was due to oxygen evolved by ferric oxide in forming ferrous oxide or ferrous silicate was never substantiated by - experimental work. Orton2 thought this explanation unlikely, as all clays should bloat at the same temperature, if this were true. He found that clays bloated in the range from IIoo° to 17oo°C. Also, many clays containing iron did not bloat at all, but fused. Orton also stated that oxida- tion of different types of carbon was a source of gas during burning of clay and should be expelled before vitrification was reached. Seger3 said that he had dissolved ferric oxide in glass with no apparent evolution of gas. Matson4 came to the conclusion that ferruginous clays burned &apos; to vitrification in an oxidizing atmosphere did not have the iron in a ferrous form. According to Wilson,= the gases responsible for bloating might be entrapped air, water, sulphur dioxide, carbon monoxide, oxygen, and hydrocarbons. He spoke of two causes of bloating: (I) incomplete oxidation below the vitrification temperature, and (2) decomposition of compounds and evolution of gases above the vitrification temperature. Decomposition of calcium sulphate was given as the principal example of the latter. Bleininger and Montgomery0 stated that if any time after vitrification began the evolution of gaseous matter was rapid enough so that pressure was produced within the clay, bloating was certain to take place, and a vesicular structure would be formed. They recognized that initial structure, rate of heating, kiln atmosphere, and many other variables affected bloating. Work done by the Emergency Fleet Corporation7 indicated that clays suitable for bloating should be high in compounds of metallic oxides, carbon, sulphur, sodium, potassium, or other equivalent compounds, which either act as a flux or give off gas. Orton2 studied the chemical status of the carbon, iron, and sulphur in clays during various stages of burning, using a Huron shale that bloated under oxidizing or reducing conditions. He found that only a small amount of sulphur remained in the clay and that it could be detected only by dissolving the clay in hydrofluoric acid; i.e., the sulphur was in combination with the silica. orton said that this sulphur was probably in the form of iron sulphide dissolved in the glass phase. The iron sulphide was not broken down by heating, but was dissolved in the basic slag or glass,

Jan 1, 1942

By J. D. Sullivan, Chester R. Austin, J. L. Nunes

It is characteristic of most shales and surface clays that a bloated or vesicular structure is produced by burning to a sufficiently high temperature, usually about 150° to 200°F. above the normal maturing temperature used when making common brick of the same material. Early investi-: gators recognized this phenomenon and attributed it to the release or expansion of gases in the vitrified piece. A number of theories have been advanced on the source of the gas and the manner in which it is evolved, but none has been proved conclusively. T. E. Jackson&apos;s1 early theory that bloating was due to oxygen evolved by ferric oxide in forming ferrous oxide or ferrous silicate was never substantiated by - experimental work. Orton2 thought this explanation unlikely, as all clays should bloat at the same temperature, if this were true. He found that clays bloated in the range from IIoo° to 17oo°C. Also, many clays containing iron did not bloat at all, but fused. Orton also stated that oxida- tion of different types of carbon was a source of gas during burning of clay and should be expelled before vitrification was reached. Seger3 said that he had dissolved ferric oxide in glass with no apparent evolution of gas. Matson4 came to the conclusion that ferruginous clays burned &apos; to vitrification in an oxidizing atmosphere did not have the iron in a ferrous form. According to Wilson,= the gases responsible for bloating might be entrapped air, water, sulphur dioxide, carbon monoxide, oxygen, and hydrocarbons. He spoke of two causes of bloating: (I) incomplete oxidation below the vitrification temperature, and (2) decomposition of compounds and evolution of gases above the vitrification temperature. Decomposition of calcium sulphate was given as the principal example of the latter. Bleininger and Montgomery0 stated that if any time after vitrification began the evolution of gaseous matter was rapid enough so that pressure was produced within the clay, bloating was certain to take place, and a vesicular structure would be formed. They recognized that initial structure, rate of heating, kiln atmosphere, and many other variables affected bloating. Work done by the Emergency Fleet Corporation7 indicated that clays suitable for bloating should be high in compounds of metallic oxides, carbon, sulphur, sodium, potassium, or other equivalent compounds, which either act as a flux or give off gas. Orton2 studied the chemical status of the carbon, iron, and sulphur in clays during various stages of burning, using a Huron shale that bloated under oxidizing or reducing conditions. He found that only a small amount of sulphur remained in the clay and that it could be detected only by dissolving the clay in hydrofluoric acid; i.e., the sulphur was in combination with the silica. orton said that this sulphur was probably in the form of iron sulphide dissolved in the glass phase. The iron sulphide was not broken down by heating, but was dissolved in the basic slag or glass,

Jan 1, 1942

By William L. Fink, Kent R. Van Horn

Zinc is one of the effective elements introduced to enhance the strength of aluminum. This strengthening is principally attributable to the high solid solubility of zinc in aluminum and the pronounced variation of solubility with temperature. Consequently an accurate determination of the solid solubility curve is desirable. The solid solubility relations have been studied by numerous investigators. Shepherd1 first established the existence of a solid solution region at the aluminum end of the diagram (-v phase) by specific volume and microscopic determinations. Bauer and Voge12 published a constitutional diagram which showed the limits of solid solubility as determined by thermal and microscopic methods. Hanson and Gayler3 presented the aluminum-zinc diagram which is now most generally accepted (Fig. 1). Chill-cast samples were given thermal treatments designed to obtain equilibrium conditions, quenched, and microscopically examined. The solubility was placed between 15 to 20 per cent at 60" C., 20 to 22 per cent at 140" C. and 36 to 38 per cent at 270" C. Sander and Meissner decidedly modified the limits of the -y phase field of Hanson and Gayler&apos;s diagram by using similar methods on chill-cast specimens annealed for a shorter period of time. Tanabe,s utilizing dynamic hard-ness, electrical conductivity and dilatometric measurements of specimens at temperature, obtained values comparable to Hanson and Gayler&apos;s at room temperature, but appreciably lower at higher temperatures. Nishimura6 concluded from age-hardening results of aluminum-zinc alloy chill castings, which had been quenched from 400" to 500" C., that the solubility of zinc in aluminum at room temperature is less than 5 * Metallurgical Division, Aluminum Research Laboratories. 1 E. S. Shepherd: Aluminum-Zinc Alloys, Jnl, phys. Chem. (1905) 9, 504. 2 0. Bauer and 0. Vogel: Aluminum-Zinc Alloys, Int. Jn1. Melallog. (1916) 8, 101. 3 D. Hanson and M. V. L. Gayler: A Further Study of the Alloys of Aluminum and Zinc. Jnl. Inst. Met. (1922) 27, 267. 4 W. Sander and K. L. Meissner: ZII~ Kenntnis der Konstitution der Aluminium-Zinklegierungen. Ztsch. f. Metallkunde (1922) 14, 385. 4 T. Tanabe: Studies in the Aluminum-Zinc System, Jnl. Inst. Met. (1924) 32, 415 6 H. Nishimura: On the Age-Hardening of Aluminum-Rich Al-Zn Alloys. Mem. Kyoto Imp. Univ. (1924) 3, 133.

Jan 1, 1932

By K. A. Jackson, J. D. Hunt

A new classification of eutectics is proposed, based on tlze entvopies of wzelting of the tuio eutectic phases. The clnssification was used to predict suitable tvansparent analogs of the metallic systems. Experimental confir?nation loas obtained for the theovetical shape of the lamellar solid-liquid interface, fov the fault mechanisms of lanzellar spacing changes, and for the development of low-energy solid-solid boundaries between the lamellae. An explanation is presented to account jov the irvegular and coinplex regular structures zrhich are found in some eritectic systems. FrOM experimental observations, single-phase materials can be divided into two groups according to their solidification characteristics, those that grow as faceted crystals and those that do not. acksonl&apos; showed from thermodynamic reasoning that the type of growth depended on a factor a which was almost thg entropy of melting. Most nonmetals have high entropies of melting (a greater than 2) and grow with crystalline facets. Most metals have low entropies of melting (CY less than 2) and grow almost isotropically with no facets. The authors propose that eutectics may be classified in a similar manner. There are three groups of eutectics, those in which both phases have low entropies of melting, those in which one phase has a high and the other phase has a low entropy of melting, and those in which both phases have high entropies of melting. Lamellar or rodlike structures are formed in systems in which both phases have low entropies of melting. In these alloys dendrites of either phase may be formed, when the alloy is rich in the relevant component. Examples are Pb-Sn, Sn-Cd, Pb-Cd, Sn-Zn, Al-Zn. Irregular, Fig. 14((), or complex regular, Fig. 14(b), structures are formed in alloys in which one phase has a high entropy of melting and the other has a low entropy of melting. Examples are A1-Si, Zn-MgzZnll, Pb-Bi, Sn-Bi. When the alloys are rich in the low entropy of melting phase, dendrites are formed; when the alloys are rich in the high entropy of melting phase, faceted primary crystals are produced. These crystals are sometimes called hoppers or pseudodendrites. In this work the term dendrite will only be used to describe nonfaceted primary crystals. Dendrites are not formed during solidification in high entropy of melting single-phase materials. The third group of eutectics includes alloys in which both phases have high entropies of melting. Each phase grows with a faceted solid-liquid interface. Since most metals do not have high entropies of melting, metallic examples in this eutectic group are rare. However they may occur between some intermetallics and semiconductors or semimetals such as silicon, germanium, and bismuth. Attempts have been made to study eutectic solidification visually by watching the growth process.374 Since metals are not transparent, the observations had to be made on external surfaces. This difficulty can be overcome by using transparent analogs of the metallic systems. As was mentioned earlier, most single-phase compounds have entropies of melting greater than 2 and so grow as faceted crystals. Recently organic materials with entropies of melting less than 2 were investigated.&apos; These materials grow in exactly the same way as the low entropy of melting metals. When the materials are pure, they grow with a solid-liquid interface parallel to an isotherm; when they are impure, cells or dendrites are formed. Since these materials are transparent, have low melting points, and even have cubic structures, they should be ideal for making up transparent analogs of the metallic eutectics. The purpose of the present work was to investigate these organic eutectics and to see whether this quite different series of eutectics could be classified in the same way as the metallic systems. The observations made on the organic alloys are also discussed with reference to the current theories of lamellar growth. Explanations are proposed to account for the structures formed in the other eutectic groups. EXPERIMENTAL Thin cells containing the organic alloys were uni-direction ally solidified on a specially constructed microscope stage.&apos; Uniform growth rates were obtained by moving the cells, with a motor drive, through a fixed temperature gradient, so that the solid-liquid interface remained stationary with respect to the microscope objective lens. The cells were made by fusing two microscope cover slides 7/8 by 7/8 by 1/100 in. together on three sides, leaving a gap of 1 to 3 mils between the slides, and these were filled by surface tension. A preliminary investigation of the phase diagram between two components could be made very rapidly. One side of the cell was filled with component A and the other side with component B. Since only a small amount of mixing could occur every composition from pure A to pure B was present in the cell. When the cell was placed in the temperature gradient a pictorial representation of the phase diagram was obtained. Eutectics, peritectics, "interorganics", and solid -solid transformations could be readily detected. Fig. 1 shows part of a eutectic phase diagram. The Sample was first grown slowly then stopped. The two

Jan 1, 1967