Search Documents

By G. Nabi, W-K. Lu

Cylindrical specimens of natural dense hematite were reduced to magnetite at atmospheric pressure in H2-H2O mixtures of known composition over the temperature range 1084° to 1284°K. The rate of reduction was measured by the rate of movement of the interface between hematite and magnetite. The diffusion of gases through the gaseous boundary layer, the magnetite layer, and the interfacial chemical reaction were all considered in the interpretation of experimental data. The mass transfer coefficient through the boundary layer was calculated using accepted correlations. Values of the chemical reaction rate constant and the diffusivity of hydrogen in the magnetite phase were determined. THE present investigation is concerned with the reduction kinetics of natural hematite to magnetite by H2-H2O mixtures in the temperature range 1084" to 1284°K at atmospheric pressure. This reaction is the first step in the series of topochemical reactions in the process of reducing hematite to iron. Kinetic information of the simple steps such as hematite-magnetite transformation is necessary in order to have a better understanding of the complex processes of hematite reduction in iron-making. It also has direct industrial significance because magnetic roasting is one of the most important methods in benefication of lean ore.&apos; Although many technical papers have been published on the process of magnetic roasting and iron oxide reduction, very little information is available in the literature concerning the fundamental nature of hematite reduction to magnetite by reducing gases. Hansen et al.2 reduced the dense synthetic pellets of high-purity oxide in CO-CO2 mixtures and determined the reaction rate by weight-loss method. They were able to interpret most of their results by applying the interfacial area control theory developed by Mckewan.3 In contrast, Wilhelm and St. Pierre,4 who studied reduction of hematite to magnetite in H2-H2O mixtures by weight-loss method, stressed that the resistance of the porous magnetite layer to the diffusion of gases cannot be neglected in consideration of the overall reaction rate. In the present study the contributions of interfacial chemical reaction, diffusion of gases through the magnetite phase, and the gaseous boundary layer to the overall reaction rate will be considered. APPARATUS AND PROCEDURE Hematite Specimens Preparation. Natural hematite ore from Vermillon range of Northern Minnesota was selected for the present investigation because of its high purity and thermal stability. Chemical analysis of five samples gave the following average values: 67.52 pct total iron (96.62 pct Fe2O3, 0.28 pct FeO, 0.03 pct metallic iron), 2.53 pct SiO2, <0.07 pct MgO, 0.03 pct CaO, 0.05 pct combined mixture, 0.07 pct loss on ignition, and 0.34 pct other. Cylindrical specimens of 0.93 cm in diam and 2.7 cm in length were drilled from slabs of ore with a water-cooled diamond core drill. These specimens were heated to 1000°C and furnace-cooled. Specimens with silica pockets developed large cracks. The uncracked specimens were heated a second time, and their surfaces were carefully examined with a microscope. Those with hairline cracks or surface inhomoaenitv-- were rejected. Preparation of H2-H2O Mixtures. H2-H2O mixtures were prepared by the combustion of H2-O2, mixtures in a pyrex glass chamber in the presence of a catalyst. Alumina pellets coated with palladium, supplied by Englehard Industries, were used as the catalyst. Purified grades of hydrogen and oxygen were used which were repurified by usual techniques. Hydrogen before entering the combustion chamber was passed through an activated alumina H2O absorption bulb, with copper turning at the top. The cover of this bulb was not made pressure-tight so that any pressure development in the hydrogen line would cause the cover to blow off and also the copper turnings would act as a flame arrester in the case of a flashback from the combustion flame. Oxygen flow rates were measured with a bubble flow meter after purification with 1 pct accuracy. Hydrogen flow rates were measured by "precision wet test meter" and the amount of unburnt hydrogen was accurately measured by a bubble flow meter, after condensing water vapor in the gaseous stream. The Pyrex glass bulb contained concentric Vycor glass tubes as shown in Fig. 1. Oxygen was prevented from diffusing into the hydrogen line by threading platinum wire through pores at the combustion end of gas inlet tube. The glass bulb was heated with a Kanthal heating wire pasted in asbestos paper. The surface temperature of the bulb was measured with a thermocouple and adjusted to remain at approximately 350°C. The gaseous reaction chamber also served as a preheater for gases to avoid thermal segregation. The following sequence of operation was adopted. 1) Nitrogen was passed through the outer concentric tube to purge the catalyst bulb of oxygen. 2) Hydrogen was introduced through the inner tube until a steady flow was obtained. 3) Oxygen was then introduced into the nitrogen stream passing through the outer tube. 4) When combustion had commenced and a flame was visible over the platinum wire, the N2 was turned off.

Jan 1, 1969

By J. O. Brittain, N. R. Adsit

It has been suggested that grain boundary motion during creep is a two-stage process, i.e., sliding followed by migration. Wienbergl found alternate sliding and migration of aluminum tricrystals tested in shear. He concluded that curves of grain boundary sliding (G. B. S.) vs time were not reproducible from specimen to specimen. Couling and Roberts,&apos; who worked on polycrystalline magnesium, found that sliding and migration were interdependent. They were able to correlate the amount of sliding with the number of sliding-migration cycles, i.e., the amount of migration observed metallographically. Rhines, Bond, and Kissel found that the curves of grain boundary sliding vs time were spasmodic but they did not find any migration of the boundary. Some recent creep tests on bicrystals of high-purity zinc (99.99 pct) help to elucidate the role of grain boundary migration in the G. B. S. process. The experimental technique and apparatus are described elsewhere. The tests were conducted in vacuum or a protective atmosphere of argon. All specimens were stressed in simple shear along

Jan 1, 1961

By J. B. Clemmer, F. D. DeVaney, H. A. Doerner

Production of magnesium metal in the United States during the past decade has increased from less than 600,000 lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgCO3), usually is associated with limestone (CaC03) and dolomite (MgCO3. CaC03). It occurs in crystalline and microcrystalline (sometimes termed amorphous) forms.2 The more common crystalline mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedra1 crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories. The deposits are extensive, some veins being hundreds of feet wide. The boundaries of the veins are indefinite, and the magnesite is interfingered with dolomite. Calcite, talc, serpentine, quartz and shale are disseminated through the deposits. The quality of the ore cannot be determined by appearance or by simple tests; chemical analysis is required. These features make it difficult to determine the boundaries or total quantity of workable ore.3 Only the higher-grade ores are mined, and a considerable proportion of the magnesite content is discarded by hand-sorting and log-washing methods. After calcining, the sorted product meets the specifications for usual refractory material, as it contains approximately 81 per cent MgO, 7 per cent SiO2, 6 per cent CaO and 6 per cent Fe203 + A1203. A sample of the reject material had the following analysis after calcining: 65.4 per cent MgO, 6.3 CaO, 21.1 SiO2 and 6.5 R2O3. The percentage reported as R2O3 includes compounds whose chlorides are acid-soluble but give precipitates in ammoniacal solution that are ignited and weighed. The more common constituents are Fe2O3, A1203 and TiO2. The sorted magnesite product is not the best grade. even for refractory purposes, and leaves much to be desired for a reduction process. The rejected material contains a large proportion of magnesite. It is apparent that an effective concentration method would yield a higher recovery and a better product. In general, the refractory grade is not suitably pure for other uses. Recent developments in the production of

Jan 1, 1943

By J. B. Clemmer, F. D. DeVaney, H. A. Doerner

PRODUCTION of magnesium metal in the United States during the past decade has increased from less than 6oo,ooo lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgCO3), usually is associated with limestone (CaCO3) and dolomite (MgCO3CaCO3). It occurs in crystalline and microcrystalline (sometimes termed amorphous) forms.2 The more common crystalline mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedral crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories. The deposits are extensive, some veins being hundreds of feet wide. The boundaries of the veins are indefinite, and the magnesite is interfingered with dolomite. Calcite, talc, serpentine, quartz and shale are disseminated through the deposits. The quality of the ore cannot be determined by appearance or by simple tests; chemical analysis is required. These features make it difficult to determine the boundaries or total quantity of workable ore.3 Only the higher-grade ores are mined, and a considerable proportion of the magnesite content is discarded by hand-sorting and log-washing methods. After calcining, the sorted product meets the specifications for usual refractory material, as it contains approximately 81 per cent MgO, 7 per cent Si02, 6 per cent CaO and 6 per cent Fe203 + A1203. A sample of the reject material had the following analysis after calcining: 65.4 per cent MgO, 6.3 CaO, 21.1 Si02 and 6.5 R203. The percentage reported as R203 includes compounds whose chlorides are acid-soluble but give precipitates in ammoniacal solution that are ignited and weighed. The more common constituents are Fe203, A1203 and Ti02. The sorted magnesite product is not the best grade, even for refractory purposes, and leaves much to be desired for a reduction process. The rejected material contains a large proportion of magnesite. It is apparent that an effective concentration method would yield a higher recovery and a better product. In general, the refractory grade is not suitably pure for other uses. Recent developments in the production of

Jan 1, 1940

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O&apos;Brien,&apos; of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in Professor O&apos;Brien&apos;s paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in terms of mass per unit time by w Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m8. Mass per unit volume of liquid by mi Mass per unit volume of mixture by 11 We then have as an expression for the solids load: w = pqmm The work done per unit mass, p, on the mixture to move it along the pipe the

Jan 1, 1947

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O&apos;Brien,&apos; of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in Professor O&apos;Brien&apos;s paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in terms of mass per unit time by w Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m8. Mass per unit volume of liquid by mi Mass per unit volume of mixture by 11 We then have as an expression for the solids load: w = pqmm The work done per unit mass, p, on the mixture to move it along the pipe the

Jan 1, 1947

By D. E. Wolfson, D. A. Reynolds, F. W. Smith

IN 1948 the U. S. Bureau of Mines began a three-phase program to evaluate the extent and quality of U. S. coking coal: 1) a factual appraisal of known recoverable reserves in beds of mineable thickness, 2) a study of preparation characteristics, and 3) a study of carbonization properties. A previous paper presented the methods used in assessing reserves.&apos; Although this investigation is only partly completed, data on coking properties of the Pittsburgh district coals are now available. The results are presented in this article. When coals are selected for manufacture of metallurgical coke more factors must be considered than for any other major use, as no basic industry requires coal of such high quality and uniformity. This is particularly true in the Pittsburgh district, where blast furnace practice is based on use of cokes from high quality coals. Although it is true that inferior coals are carbonized in other industrial areas, both here and abroad, the Pittsburgh coals are the best economically obtainable in the required tonnages, even though they are not the most desirable for metallurgical use. In the general evaluation of suitability of coals for coke making, particular attention is given to: 1) reserve, 2) ash and sulfur content, 3) inherent properties of forming strong, well fused coke, 4) expanding characteristics, and 5) blending properties. Items 1 and 2 are covered in detail in the first two phases of the survey, and coking behavior is considered in items 3 through 5. Problems is Coal Evaluation: Although not all coal beds of immediate or potential use to the coking industry in the Pittsburgh area have been tested for their coking properties, enough tests have been made to permit certain generalized statements. Virtually all the coals that will be used in this district are from the Appalachian region, and except for high oxygen coals from outcrops or stripping operations, they are coking coals. Hence the evaluation problem is not so much that of distinguishing between coking and noncoking coals as attempting to measure quantitatively differences in the coking and expanding properties of the better coking coals. Quantitative differentiation between good coking coals, is complex, since differences in their coking abilities are frequently of about the same magnitude as the precision of the test. Small-scale tests are generally unsuitable for measuring these slight differences, and there has been gradual acceptance of pilot-scale tests. Test Methods Employed: All the data reported here were obtained in two units known as the Bureau of Mines-American Gas Association (BM-AGA) carbonization apparatus and the sole-heated expansion oven. The BM-AGA unit, which consists essentially of a cylindrical steel retort about 18 in. diam and 26 in. high, carbonizes enough coal (180 lb) to allow evaluation of the coke by standard methods of the American Society for Testing Materials. The BM-AGA carbonization procedure and methods of testing the gas, liquid, and solid products have been described.&apos; Expanding characteristics of the coals were determined in the sole-heated expansion oven," wherein the coal charge, heated from the bottom only, is carbonized under a constant applied force and the linear expansion or contraction is measured. Although results in this oven have never been quantitatively correlated with the expansion behavior of coals in conventional slot ovens, they are useful in assessing expansion behavior. In this report discussion will be confined to results obtained from these pilot-scale units, although the following data are available for most coals: proximate and ultimate analyses, free swelling index, agglutinating value, and plasticity. Sources of Coals Tested: In selection of coals for coke manufacture, economic considerations are as important as quality, and each coke plant balances these two factors to meet requirements of the most satisfactory coke at lowest price. Although these economic factors may in some instances outbalance small differences in coke quality, they are usually specific to each coke plant and cannot be given in any general statement. Recognizing that coal and plant operating costs are beyond the scope of the survey, the USBM evaluates the coking quality of various coals without regard to their competitive economic status. For the purpose of this article, coals of interest to the Pittsburgh district are arbitrarily defined as

Jan 1, 1958

By R. Stefanko, Y. J. Wang, H. R. Hardy, R. Y. Kim

Since 1964, the Dept. of Mining at The Pennsylvania State University has been carrying out extensive studies associated with the phenomena of microseismic activity and inelastic behavior in geologic materials. Briefly, the program to date has involved the following stages 1) Study of the microseismic noise and energy rates for selected geologic materials under incremental, uniaxial tension.1,2 2) Investigation of the frequency spectra of microseismic activity of selected geologic materials under incremental, uniaxial tension.3,4 3) Investigation of the time-dependent inelastic deformation of geologic materials and the analysis of such deformation in terms of mechanical models.5, 6 4) Simultaneous study of microseismic activity and time-dependent inelastic deformation in geologic materials under incremental, uniaxial compression.7,8 Details of the research involved in stage 4 of the program constitute the subject of this chapter. It should be noted that the majority of the experimental data quoted in this chapter forms part of a thesis to be presented by one of the authors (Kim) in partial fulfillment of the requirements for the Ph.D. degree in mining engineering at The Pennsylvania State University. During the last two or three years, a number of important papers have been published which deal primarily with the fundamental structure and mechanical behavior of geologic materials. Recent papers 9,10 have provided research workers in the rock mechanics field with a meaningful overall picture of rock as a structural material. The concept that many

Jan 1, 1970

By C. S. Barrett, C. T. Haller

Twinning in magnesium is known to occur profusely under certain conditions, and when it occurs in polycrystalline materials it brings about a partial or even a complete change in the preferred orientation. The amount of research on this subject, however, has not been in proportion to its importance as a mechanism of deformation and reorientation. Much of the research has been limited to twinning in single crystals. The present study1 concerns polycrystalline sheet, and is an investigation of the twinning produced by plastic deformation as a function of the following variables: 1. Direction and type of deformation. 2. Amount of deformation. 3. Speed of deformation. 4. Temperature of deformation 5. Composition and temper of the sheet. 6. Twins previously produced. 7. Twins previously produced, then annealed. By proper control of these variables it is shown that, on a laboratory scale, samples can be produced that are free from preferred orientations. The materials used were samples of commercial magnesium-alloy sheets with nominal compositions given in Table I. X-ray diffraction was used in most of this work to detect the twins and to estimate the amount of twinning. Since twinning on (102) planes causes a re-orientation of the crystal lattice by 86", it is very easy to study with X-ray diffraction patterns, particularly if one notices the diffraction ring from the basal plane— the 002 reflection. By properly directing the X-ray beam, it is possible to produce 002 reflections from twinned material at, say, the 6 and 12 o&apos;clock positions on the 002 ring, with the untwinned material reflecting to 3 and 9 o&apos;clock positions; and by judging the relative intensity of the arcs on the diffraction ring at these positions, it is possible to judge the amount of twinned material relative to the untwinned. This X-ray method of estimating the amount of twinning is generally superior to metallo-graphic observation, for it was found

Jan 1, 1947

By C. S. Barrett, C. T. Haller

Twinning in magnesium is known to occur profusely under certain conditions, and when it occurs in polycrystalline materials it brings about a partial or even a complete change in the preferred orientation. The amount of research on this subject, however, has not been in proportion to its importance as a mechanism of deformation and reorientation. Much of the research has been limited to twinning in single crystals. The present study1 concerns polycrystalline sheet, and is an investigation of the twinning produced by plastic deformation as a function of the following variables: 1. Direction and type of deformation. 2. Amount of deformation. 3. Speed of deformation. 4. Temperature of deformation 5. Composition and temper of the sheet. 6. Twins previously produced. 7. Twins previously produced, then annealed. By proper control of these variables it is shown that, on a laboratory scale, samples can be produced that are free from preferred orientations. The materials used were samples of commercial magnesium-alloy sheets with nominal compositions given in Table I. X-ray diffraction was used in most of this work to detect the twins and to estimate the amount of twinning. Since twinning on (102) planes causes a re-orientation of the crystal lattice by 86", it is very easy to study with X-ray diffraction patterns, particularly if one notices the diffraction ring from the basal plane— the 002 reflection. By properly directing the X-ray beam, it is possible to produce 002 reflections from twinned material at, say, the 6 and 12 o&apos;clock positions on the 002 ring, with the untwinned material reflecting to 3 and 9 o&apos;clock positions; and by judging the relative intensity of the arcs on the diffraction ring at these positions, it is possible to judge the amount of twinned material relative to the untwinned. This X-ray method of estimating the amount of twinning is generally superior to metallo-graphic observation, for it was found

Jan 1, 1947

By W. Hodge, A. F. Haskins, R. M. Evans

Refractory boron compounds are shown to resist corrosion by molten zinc. Coatings were made from ferroboron and manganese boron by several methods: welding, hard facing, and pack diffusion; and techniques of coatings are very important. Mechanical failure of the diffusion coatings can be partially eliminated by applying them to type 416 chromium steels rather than carbon steels. Welded coatings made with a tungsten arc are better than those made by other welding methods. Sintered compacts of mixtures of iron and chromium borides developed strengths of about 30,000 psi. They resisted corrosion of zinc at 600°C and oxidation at higher temperatures. MOLTEN zinc rapidly attacks common metals of construction. The rate of attack is greatly amplified at temperatures over 500°C. However, there are many applications where it is necessary, or at least advantageous, to use metal construction, such as for galvanizing pots and zinc smelter equipment. Condensers and agitator linings used in continuous zinc smelting processes are eroded and corroded by violently agitated molten zinc. Pumps, tubing, and other parts to permit transfer of molten zinc would be desirable in many zinc handling operations. The development of metallic materials which are resistant to molten zinc also might permit its use as a heat-transfer medium in modern high efficiency power plants. In reviewing previous work on zinc-resistant metals, it was evident that most of the available data refer to corrosion at temperatures just above the melting point. Tungsten and high Mo-Fe alloys containing more than 80 pct Mo resist corrosion by molten zinc.&apos;, &apos; Imhoff states that because chromium is not attacked by zinc, chromium plating improves galvanizing pot life." Nitrided cast iron has been used in die-casting machines&apos; where the molten alloy is 96 pct Zn and 4 pct Al. Other metals that have been suggested as of possible value for zinc resistance are columbium, tantalum, and titanium.V he corrosion of steel by zinc has been discussed by many authors,z, "2 None of these materials resisted corrosion by molten zinc at the temperatures used in this investigation, i.e., 600" to 700°C. I. Exploratory and Resistant-Coating Tests To make a study of zinc-resistant metals, exploratory tests were conducted to sort out roughly those materials which seemed most worthy of further development. This preliminary study included both solid metals and surface coatings. Exploratory Corrosion Tests in Molten Zinc—In initiating a study of this problem, numerous samples of metals and alloys were evaluated by dynamic corrosion tests made at 440 °C. Each metal was tested in its most readily available form, which, because of shape and size, was often unsuited for standard corrosion testing. The equipment used for dynamic corrosion testing of all materials, except in a few initial experiments, is shown in Fig. 1. Samples were tied to tungsten rods with tungsten wire, immersed in the zinc, and revolved at 12 rpm about the circumference of a 4 in. diam circle. Speed of travel was about 12.5 fpm. The molten zinc was protected from oxidation by an atmosphere of carbon monoxide, or, at a later period in the program, by a 9:1 mixture of nitrogen and hydrogen. When the effect of both molten metal and atmosphere was desired, the zinc level was lowered. Special high grade zinc was used in all of the corrosion tests. Corrosion losses for materials tested are shown in Tables I and 11. Whenever the materials were available in suitable form, the losses are reported in mils per year. It was recognized that weight losses on irregularly shaped specimens did not show the corrosion rate but the important consideration—poor resistance to corrosion—could be determined readily.

Jan 1, 1956

By Donald W. Scott, L. A. Roe, B. J. Sweo

INTRODUCTION THIS paper describes the application of ore-dressing methods to the reclamation of milled frit from over-spray, or waste, porcelain enamel. Frit is the name given by enamelers to a granulated glass produced by the smelting and subsequent water quenching of various ingredients capable of forming a glass, usually including a compound to produce opacity. It is the major component of porcelain enamel, and normally commands a price ranging from 7 to 12 cents a pound. In the preparation of a white enamel slip, usually 6 or 7 parts of clay, 2 parts of opacifier, small amounts of electrolytes, in some cases inorganic color stabilizers and organic dyes, and 35 parts of water are added to loo parts of frit; the mixture then is milled to a fineness of the order of 92 to 95 pct through a 200-mesh sieve. The frit forms the base of the enamel; the opacifier imparts opacity or reflectance; the clay suspends the frit while in slip form and serves as a binder&apos; in bisque form (dry and unfired); and the electrolytes control the workability. Spraying is used commercially, in many cases, to apply the finish coat of enamel to the ware, prior to drying and firing. In the spraying operation, only about 50 pct, by dry weight, of the enamel slip adheres to the surface of the ware, the remainder forms the over-spray. From 1/2 to 2/3 of the overspray goes up the flue where it is lost or recovered, depending on whether the plant is equipped with a dust-collecting installation; the coarser portion of the overspray is collected in the spray booth. The former product is termed flue reclaim enamel, and the latter booth reclaim enamel. Although the spraying operation is done in specially constructed booths, which are partially or completely enclosed, it is extremely difficult to keep out contaminating dirt, which joins the reclaim. Some present-day large enameling plants use 20 tons of frit a day, of which 10 tons go into reclaim with a potential value of $1400 to $2400. When two-coat finish enamels were common, the reclaim was used satisfactorily for the undercoat, but the relatively recent advent of one-coat finish enamels prevented use of the reclaim because, even when blended with first-run enamels, it gave dirty finishes with poor gloss. It was thought that the pitting and specking encountered with reclaimed enamels were caused by the contaminating dirt, and that the poor gloss was caused, primarily, by the high clay content; more clay usually was added to give proper suspension properties to the slip when the reclaim was used. A clay content in excess of about 10 pct usually imparted refractoriness to porcelain enamels. Present-day one-coat porcelain enamels must combine high gloss and opacity with freedom from surface defects. Methods of beneficiating the over-spray,

Jan 1, 1947

By Lloyal O. Bacon

In the spring of 1952 Calumet and Hecla Inc. began a geophysical program near Shullsburg, Wis., in the Wisconsin-Illinois lead-zinc district, to assist the geological and drilling exploration programs. Sphalerite, the ore mineral in this area, occurs with a considerable amount of marcasite. In general the higher the percentage of sphalerite in the ore, the higher the percentage of marcasite; however, there may be mineralized zones high in marcasite but low in sphalerite. Orebodies in general are relatively narrow and elongated.

Feb 1, 1956

By Richard Pearce

WHILST most of the silver- and copper-bearing veins of Butte have characters somewhat similar, the Gagnon vein has certain rather remarkable features which are not noticed in any of the other mines. The silver-veins proper, as illustrated in the Alice, Lexington, Moulton, and many others, have certain well-known typical characters. Manganese is always present in variable quantities as rhodocrosite or rhodonite, associated with quartz, pyrite, and sphalerite, and with little or no copper. The copper-veins also have certain mineralogical characteristics, which are very similar, or different only in minor points. Chalcocite, chalcopyrite, bornite, enargite, with variable quantities of pyrite, may be said to represent the general mineralogical features of these lodes. It is worth noticing that while the silver-bearing lodes have more or less sphalerite, this mineral is almost entirely

Jan 1, 1888

By H. J. Ramey

The wellbore acts as a storage tank during drawdown and build-up testing and causes the sand-face flow rate to approach the constant surface flow rate as a function of time. This effect is compounded if non-Darcy flow (turbulent flow) exists near a gas wellbore. Non-Darcy flow can be interpreted as a flow-rate dependent skin effect. A method for determining the non-Darcy flow constant using this concept and the usual skin effect equation is described. Field tests of this method have identified several cases where non-Darcy flow was severe enough that gas wells in a fractured region appeared to be moderately damaged. The combination of wellbore storage and non-Darcy flow can result in erroneous estimates of formation flow capacity for short-time gas well tests. Fortunately, the presence of the wellbore storage eflect permits a new analysis which can provide a reasonable estimate of formation flow capacity and the non-Darcy flow constant from a single short-time test. The basis of the Gladfelter, Tracy and Wilsey correction for wellbore storage in pressure build-up was investigated. Results led to extension of the method to drawdown testing. If non-Darcy flow is not important, the method can be used to correct short-time gas well drawdown or build-up data. A method for estimation of the duration of wellbore storage effects was developed. INTRODUCTION In 1953, van Everdingen and Hurst generalized results published in their previous paper3 concerning wellbore storage effects to include a "skin effect", or a region of altered permeability adjacent to the wellbore. Later, Gladfelter. Tracy and Wilsey4 presented a method for correcting observed oilwell pressure build-up data for wellbore storage in the presence of a skin effect. The method depended upon measuring the change in the fluid storage in the wellbore by measuring the rise in liquid level. To the author&apos;s knowledge, application of the Gladfelter, Tracy and Wilsey storage correction to gas-well build-up has not been discussed in the literature. It is, however, a rather obvious application. Gas storage in the wellbore is a conlpressibility effect and can be estimated easily from the measured wellbore pressure as a function of time. Several approaches to the wellbore storage problem have been suggested. As summarized by Matthews, it is possible to minimize annulus storage volume by using a packer, and to obtain a near sand-face shut-in by use of down-hole tubing plug devices. Matthews and Perrine have suggested criteiia for determining the time when storage effects become negligible. In 1962, Swift and Kiel&apos; presented a method for determination of the effect of non-Darcy flow (often called turbulent flow) upon gas-well behavior. This paper provided a theoretical basis for peculiar gas-well behavior described previously by Smith. Recently, Carter, Miller and Riley observed disagreement among flow capacity k,,h data determined from gas-well drawdown tests conducted at different flow rates for short periods of time (less than six hours flowing time). In the original preprint of their paper, Carter et al. proposed that the discrepancy in flow capacity was possibly a result of wellbore storage effects. Results of an analytical study of unloading of the wellbore and non-Darcy flow were recorded by carter.14 In the final text of their paper, Carter et al.!&apos; stated that they no longer believed wellbore storage was the reason for discrepancy in their kgh estimates. In view of the preceding, this study was performed to establish the importance of non-Darcy flow and well-bore storage for gas-well testing. In the course of the study. a reinspection of the previous work by van Everdingen&apos; and Hurst&apos; was made, and the basis for the Gladfelter, Tracy and Wilsey&apos; wellbore storage correction was investigated and extended to flow testing. WELLBORE STORAGE THEORY As has been shown by Aronofsky and Jenkins,11-12 Matthews," and others, flow of gas can often be approximated by an equivalent liquid flow system. The following developnlent will use liquid flow nomenclature to simplify the presentation. Application to gas-well cases will be illustrated later. First, we will use the van Everdingen-HursP treatment of wellbore storage in transient flow to establish (1) the duration of wellbore storage effects, and (2) a method to correct flow data for wellbore storage. DURATION OF WELLHORE STORAGE EFFECTS When an oil well is opened to flow. the bottom-hole pressure drops and causes a resulting drop in the liquid level in the annulus. If V. represents the annular volume in cu ft/ft of depth, and p represents the average density of the fluid in the wellbore, the volume of fluid at reservoir conditions produced from the annulus per unit bottom-hole pressure drop is approximately: res bbl-- (V, cu ft/ft) (144 sqin./sq ft) psi -(5.615 cu ft/bbl)(pIb/cuft) ........(I)

Jan 1, 1966

By C. D. Stahl, S. M. Farouq Ali

This investigation attempts to describe and simulate the alcohol displacement process by means of a cell model, as employed in chemical engineering practice. The proposed model is more simple than previously proposed models. and utilizes parameters chosen on a theoretical basis. The model successfully reproduced the formation of the stabilized bank and the breakthrough of alcohol, the latter depending on one of the model parameters, which may be correlated with the length of the porous medium. Moreover, the effects of the phase behavior of the liquid system involved, as observed in experimental studies, were reproduced. Several variations of the basic model were devised and tested on a digital computer. These included the cases in which: (1) the actual value of fractional flow was used in cell-to-cell computations; (2) the number of cells was varied within the same run; and (3) incomplete rather than complete phase equilibrium was assumed within each cell. The proposed cell model clarifies the basic mechanism of the process. Detailed concentration profiles obtained for each cell, for instance, showed the mechanism of bank formation in relation to the phase behavior characteristics. The results obtained indicated a varying degree of phase equilibrium concommitant with changes in the velocities of the phases in an actual alcohol displacement. This condition was approximated by changing the number of cells during the simulation. Interesting information was obtained on the influence of path length on the efficiency of alcohol displacement, which has been the subject of some controversy. Certain limitations preclude the use of the proposed model as a substitute for experimental studies. The results obtained were, nevertheless, of value in interpreting the experimental results. INTRODUCTION During recent years considerable effort has been directed toward an understanding of alcohol displacement, the process whereby oil and water are recovered from a porous medium by the continuous injection of a solvent. The complex nature of the physical process involved has so far defied a complete mathematical treatment. Other methods of approach, amounting to an overall material balance, have been proposed, yielding useful information on certain aspects of the process.1-3 Taber et al, in particular, defined the displacement mechanism in terms of the phase behavior of the alcohol-oil-brine system invoIved.2 Wachmann reported a mathematical treatment of alcohol displacement subject to certain simplifying assumptions? Donohue proposed the use of a "cell model" for simulating alcohol disPlacement.5 The nature of the assumptions involved limited the utility of the model. The present work attempts to examine the variables involved in the simulation of alcohol displacement and discusses several possible versions of the basic cell model. Under certain conditions the model results are similar to the experimental results. In particular, the spontaneous formation of of the stabilized bank and the effects of the system phase behavior were successfully reproduced. PREVIOUS WORK ON CELL MODELS Cell models and the theoretical plate concept are often used in solving chemical engineering problems in which an explicit mathematical solution may be difficult or impossible to obtain. Examples of such applications occur in distillation, gas-liquid chroma tography,6 reactor technology, absorption, etc. In petroleum engineering, such a model was used by Attra7 to describe non-equilibrium gas drive, and by Higgins and Leigh ton8 to calculate sweep efficiency in water flooding. Aris and Amundsen pointed out the equivalence between the diffusion model and perfectly mixed cells connected in series.9 Deans proposed a three-parameter cell model to simulate two-component

Jan 1, 1966

By R. T. Torgerson, W. A. Baginski

Alloying studies were conducted on modifications of Cb-10W-1OHf (C-129) alloy as part of a cooperative alloy development effort between The Boeing Co. and the Wah Chang Corp. The purpose of these studies was to develop a fabricable, high- strength columbium alloy with superior melding properties. The initial investigations of alloy modifications were conducted using laboratory-melted button ingots. An alloy with the composition exhibited excellent veld ductility, elevated-ternpevature strength, and fabricability. The yttrium-modified alloy was desigrzated C-129Y and was selected for further developrnetzt. Three prodziction heats of C-129Y weve processed into sheet. Welding, forming, and tensile proper-lies are presented for this material. Tungsten-are welds of. C-129Y exhibited a minimum bend radius of 1/2T in the as-welded conditioti compared to 8T for C-129 alloy. An investigation was conducted on Disil coating of C-129Y and test data are presented on oxidation resistance and effects of re-entry environments. The excellent combination of strength, fabricability, weldability, and low transition temperature of C-129Y alloy offers potential design advantages for use of this alloy in structures of aerospace vehicles. It is atiticipated that C-129Y will rapidly supplant C-129 and similar alloys clue to the versatility provided by its impvoved welditzg properties. COLUMBIUM alloys with improved properties are required to achieve better performance and efficiency of radiation-cooled structures for re-entry vehicles and recoverable launch systems. Cooperative work by The Boeing Co. and the Wah Chang Corp. resulted in the development several years ago of C-129 alloy, a high-strength Cb-W-Hf alloy.&apos; This alloy has received favorable consideration for many advanced designs of high-temperature structures due to its excellent combination of properties. However, this alloy exhibits low weld ductility unless given a high-temperature stress-relief treatment. For this reason the development effort was directed towards modification of the C-129 alloy composition (Cb-1OW-1OHf) to eliminate the need for post-weld heat treatment. This paper describes the successful development of an alloy meeting this requirement. This new alloy was designated C-129Y and has a nominal composition of EXPERIMENTAL PROCEDURES Alloying Studies. Various Cb-W-Hf compositions were investigated using are-melted button ingots. These buttons were hot-forged using a protective glass coating and rolled into sheet specimens. Metal-lographic examination: tensile testing, and welding studies were conducted to evaluate properties of the experimental alloys. Sheet Fabrication. Three pilot production heats of C-129Y were fabricated into sheet to establish processing techniques and to determine sheet properties. The three heats consisted of 6-in.-diam ingots weighing from 140 to 250 lb. The ingots were prepared by electron-be am melting followed by vacuum-arc melting. The hafnium and yttrium additions were made during the are-melting operation by tack welding alloy strip additions to the Cb-W master-alloy electrode. The final ingots were machined into billets with samples of the machine turnings collected for chemical analysis. Ingot breakdown methods for the three heats are as follows: Ingot Ingot Heat Size Weiaht___Breakdown Method A 6 in. 250 lb Hot extrusion B 6 in. 140 lb Hot forging C 6 in. 250 lb Hot extrusion Sheet bars from the extrusion and forging operations were conditioned, recrystallized, and rolled into sheet. Initial rolling was conducted at elevated temperatures and final rolling was conducted at room temperature.

Jan 1, 1967

By G. W. Powell

ACCORDING to crank,&apos; the accumulation equations for inter diffusion in a binary system whose molal volume is a function of concentration are

Jan 1, 1965

By C. H. Burgess

ON June 5, 1947, Secretary of State George C. Marshall in a speech at Harvard University outlined a plan for the economic recovery of Europe. The plan contemplated that the United States should provide assistance which would enable the European nations better to help themselves and to help each other to reconstitute from their war-torn lands conditions which would make possible decent standards of living. The Foreign Assistance Act of 1948 was passed in April of that year, and established the Eco-

Jan 10, 1950

By Harold Margolin

The Ti-Al system certainly merits the investigative attention it has been receiving and this latest contribution by Blackburn is therefore to be welcomed. The titanium-rich end of the phase diagram shown here, as well as the diagram by crossley,17 Clark et a1.,18 and Tsujimoto and Adachi,29 reveal no other intermediate phase than Ti3A1, although a previous work by Ence and Margolin20 had reported an additional intermediate phase. Since then, Buerger Precession pictures of single crystals of 10.5, 11.5, and 12.5 wt pct A1 were made at New York university21 and the extinctions were found to be typical of a D6h a Ti structure. Some superlat-tice spots and/or streaks suggesting the presence of an Mg3Cd structure, i.e., Ti3Al, were also found. Since these specimens had been quenched from the y region20 and had revealed a Ti, it was concludedz1 that y does not exist and the structures interpreted as m + y could not be so considered. The absence of normal two-phase behavior in these structures had been indicated in the paper. Accordingly, the two-phase region y + 6 becomes a + Ti3Al and there is some agreement between the results of Blackburn and of Ence and Margolin20 as to both shape and existence above 900°C of an a + Ti3Al field. Crossley 17 proposed that Ti3Al is a line compound which decomposes congruently at 900°C. It is difficult to discount entirely the fact that clear two-phase structures, varying in amount with position in the two-phase field, could be detected above 900°C by Ence and Margolin.20 Precipitation during quenching could not have been so regular and the twin-phase syndrome17 does not apply. The heat treatment and quenching technique was essentially the same as was used by Crossley, whereas Blackburn, who used a rapid quenching procedure, also showed a two-phase a + Ti3A1 field above 900°C. If the two-phase field exists above 900° C, it is easy to picture a two-phase field which could account for the data of Crossley below 900°C without invoking a line compound existence of Ti3A1. All that would be necessary would be an 0 + Ti3Al/Ti3Al boundary which curved sharply to higher aluminum contents below 900° C. It is clear that the controversy must be solved by techniques which obtain data at elevated temperatures without quenching. It is conceivable that the difference in width of the a + Ti3N fields reported by Blackburn and by Ence and Margolin is due to the longer annealing times used by the latter investigators. The criterion for establishment of equilibrium in our work20 was the

Jan 1, 1969