Search Documents

By J. J. Kramer, W. A. Tiller, G. F. Bolling

THE axial orientations of columnar crystals in unidirectionally solidified ingots of zone-refined zinc and tin have been examined using the techniques recently described by us.' Both metals had an initial purity of 99.999+ pct before zone refining and satisfied all qualitative guides for very high purity after zone refining. Fig. 1 presents the orientations of the columnar crystals for tin and zinc, respectively. For tin, there is a preference for grains growing in the [I101 direction, i.e., the dendrite direction.' For zinc, a weak preference for the [0001] direction is seen (a random population in the unit triangle would give equal density on either side of the 60-deg circle centered on [0001]).' There was no apparent evidence for dendritic growth in either metal. These results, and those previously reported,' confirm the recent investigation by Hellawell and Herbert of casting textures observed for zone-refined lead, zinc, and tin.4 The preferred casting orientations for these metals in both the impure and zone-refined states are given in Table I. In the experiments on zone-refined lead,' it was shown that two separate textures existed: a preferred (111) nucleation texture existed at the chill surface and a preferred (111) texture developed during solidification. Either effect is sufficient to produce the result recorded in Table I. Similarly the results recorded for tin and zinc may be attributable to either a preferred nucleation or a preferred growth phenomenon and additional experiments are required to separate these two possible explanations. Hellawell and Herbert' attribute their results to a preferred growth process and account for it on the basis of a "layer-growth" model proposed much earlier by one of the present authors.5 An equally satisfactory growth model would be that based upon anisotropic surface energies. However, both of these growth models would indicate that the preferred growth direction for very pure metals should be normal to the plane of closest packing in the metal. This is consistent for zinc but, contrary to the conclusion of Hellawell and Herbert, it is not consistent for tin since here the (100) is expected to exhibit a greater density of packing than the (110). Although tin is expected to exhibit an anisotropy of thermal conductivity, we would expect the thermal conductivity to be the same in the [1101 as the [l00]

Jan 1, 1963

By F. Weinberg

It has been suggested, for some time, that the behavior of metals under high-temperature creep conditions is strongly influenced by the behavior of the grain boundaries present in the material. This has led to a number of investigations1-6 in which attempts were made to measure the properties of the grain boundaries themselves, both to determine their contribution to the creep process and to obtain further knowledge of their intrinsic structure and properties. The present investigation was undertaken to extend the observed data under more closely controlled experimental conditions and to attempt to clarify sonie of the discrepancies in the literature. A brief report of the preliminary results has been published.7 EXPERIMENTAL PROCEDURE For the present investigation, controlled orientation specimens were used having plane boundaries which terminated at the specimen surface. Trierys-tal specimens were used instead of the bicrystal type of Puttick and King,' in order to simplify the gripping technique required to apply a shear stress along the boundary. The aluminum used was obtained from the Aluminum Francaise and was of 99.994 pct purity, containing 0.002 pct each of Cu, Fe, and Si. The aluminum tricrystals were grown horizontally from the melt, in graphite boats, and in an argon atmosphere, following the technique developed by Chalmers.' The orientation of the tricrystals was controlled by using seed crystals separated by mica inserts. Thermal conditions were adjusted to produce tricrystals having boundaries which were macroscopically straight, parallel to the growth direction, and perpendicular to the top surface. Following growth, the tricrystals were carefully cut with a jeweller's saw to the test specimen shapes shown in Fig. l(a) and l(b). In Fig. 1(a), the boundaries subjected to shear stresses are indicated AB and CD: Points A and C are the ends of the mica inserts separating the seed crystals; points B and D are at lateral cuts made in the specimen. It was found that the slots left by the mica inserts at A and C had to be enlarged slightly, by cutting, to ensure that the boundary terminated freely at these points. A shear stress was applied to the boundarks by gripping the upper two legs in file-faced Inconel grips and suspending a weight from the lower part of the specimen held in similar grips, as shown schematically in the diagram. The test specimens shown in Fig. 1(b) were cut from long

Jan 1, 1959

By John S. Marshall

The purpose of this paper is to present to the profession data and experience obtained over a period of 5 years in the operation of 87 shaker-conveyor units, and the production of 2,169,638 tons of run-of-mine anthracite coal. The data are not generally available and should be of interest to those concerned with the operation of anthracite and bituminous mines. To simplify comparison, a ton of 2000 lb. of raw run-of-mine coal has been used as the production unit throughout this paper. Mining Methods and Equipment The mine is in the vicinity of Wilkes-Barre, Pa., in the Buried Valley area of the Susquehanna River. Seven veins were mined, varying in thickness from 18 in. to 8 ft. The cover overlying the veins varied from 200 to 800 ft. Three-fourths of the 1200 acres of property was covered with from 100 to 200 ft. of water-bearing gravels and clays, which prevented first mining under rock cover less than 50 ft. and pillar removal under rock cover less than 100 ft. The property was opened by two shafts sunk on the mountainside to avoid the sand and gravel present in the river valley. The veins dipped an average of 5" from the shafts. In certain areas the veins were practically flat and in some places a reverse pitch as high as 5" was encountered for short distances. A daily output of 3800 tons was hoisted on a two-shifi; hoisting operation. The mining consisted of 75 per cent pillar removal, and of the total production in the later years of operation 80 per cent was loaded by shaker conveyors, chain conveyors and scraper loaders. Shaker conveyors accounted for 70 per cent of the total output; chain conveyors and scraper loaders for 10 per cent. All conveyor work was double-shifted and 25 per cent was triple-shifted. A total of 87 shaker-conveyor units were on the property, of which 75 were kept in operation at all times.

Jan 1, 1940

By John S. Marshall

The purpose of this paper is to present to the profession data and experience obtained over a period of 5 years in the operation of 87 shaker-conveyor units, and the production of 2,169,638 tons of run-of-mine anthracite coal. The data are not generally available and should be of interest to those concerned with the operation of anthracite and bituminous mines. To simplify comparison, a ton of 2000 lb. of raw run-of-mine coal has been used as the production unit throughout this paper. Mining Methods and Equipment The mine is in the vicinity of Wilkes-Barre, Pa., in the Buried Valley area of the Susquehanna River. Seven veins were mined, varying in thickness from 18 in. to 8 ft. The cover overlying the veins varied from 200 to 800 ft. Three-fourths of the 1200 acres of property was covered with from 100 to 200 ft. of water-bearing gravels and clays, which prevented first mining under rock cover less than 50 ft. and pillar removal under rock cover less than 100 ft. The property was opened by two shafts sunk on the mountainside to avoid the sand and gravel present in the river valley. The veins dipped an average of 5" from the shafts. In certain areas the veins were practically flat and in some places a reverse pitch as high as 5" was encountered for short distances. A daily output of 3800 tons was hoisted on a two-shifi; hoisting operation. The mining consisted of 75 per cent pillar removal, and of the total production in the later years of operation 80 per cent was loaded by shaker conveyors, chain conveyors and scraper loaders. Shaker conveyors accounted for 70 per cent of the total output; chain conveyors and scraper loaders for 10 per cent. All conveyor work was double-shifted and 25 per cent was triple-shifted. A total of 87 shaker-conveyor units were on the property, of which 75 were kept in operation at all times.

Jan 1, 1940

By L. Albert, A. M. Cameron, J. W. Gullick

International Nickel has 15 operating mines in Canada, and. 3 mines which are being maintained on a standby basis. Annual production is about 20 million dry short tons of ore, most of which is from underground mines, the remainder from open pit mines. Although some of the underground mines are served by ramps for trackless vehicles, most men, materials and ore are hoisted in vertical shafts. In addition to shafts and raises for ventilation and service purposes which are not equipped with hoisting plants, there are now 28 vertical shafts at Inco mines served by 47 hoists. Of these, 22 shafts and 36 hoists are located in the Sudbury District of Ontario, one shaft and two hoists are at the Shebandowan mine in Western Ontario, and 5 shafts with 9 hoists are located near Thompson, Manitoba. This paper describes the components of Inco hoisting plants-which have been applied at different times and under different conditions, and indicates the rationale for the various designs. Some engineering and maintenance practices, considered advantageous, are also described. MINE SHAFTS Many of the shafts sunk in the early days of the Sudbury District, on what are now Inco properties, were inclined shafts. Of the identifiable shafts sunk between 1885 and 1920, thirteen were inclined and at least four were vertical. Since 1920, thirty vertical and two inclined shafts have been sunk. All of the inclined shafts have been abandoned for hoisting purposes but the majority are still in use as service or ventilation ways. Shafts at Thompson- and Shebandowan are all vertical. The vertical shafts range from 2 or 3 compartment exploration and development shafts to 6 compartment shafts for ore, man and material hoisting. They vary in depth from 1,050 to 7,137 feet and in addition to hoisting compartments all contain manway and service compartments. Prior to 1948, unlined rectangular shafts with timber sets and guides were used. The rectangular cross-section was favoured since the rock is competent, the shape compatible with timber set framing, and since available shaft space could be used efficiently. Resistance to air flow was not of prime importance. Concrete linings were introduced for the first time at the Creighton No. 7 Shaft which was collared in 1948. All major shafts since that date have been concrete lined. Vertical set intervals were increased in steps, with the introduction of structural steel sets secured to the concrete linings. Whereas 7 foot set intervals were used with timber framing, this increased to 10 feet 6 inches with steel sets and more recently to 15 feet with steel and steel backed wood guides. With the advent of deeper shafts, or shafts which are expected to be deepened, the trend is to circular concrete lined shafts. The majority of shaft guides in service are of select Douglas Fir. This practice commenced as a component of timbered shaft design but continued as a

Jan 1, 1975

By J. W. Spretnak, H. R. Ogden, A. G. Imgram

The effect of working reduction, stress-relief annealing, and recrystallized grain size on the tensile and notch-tensile properties of molybdenum and Mo-0.5 Ti was studied. It was found that increasing the amount of working reduction increased the strength and reduced the tendencies toward brittle behavior. Stress -relief annealing did not alter the strength but lowered the transition temperature. Increasing the recrystallized grain size lowered the strength and raised the transition temperature. The notch -unnotch strength ratio began to decrease with decreasing temperature at temperatures below those at which the notched ductility fell to zero for all of the micro structural conditions investigated. BEING bcc metals, the refractory metals in Groups Va and VIa (V, Cb, Ta, and Cr, Mo, W) undergo a ductile-to-brittle transition and exhibit brittle fractures at low temperatures. Previous research has shown that molybdenum and tungsten not only have higher transition temperatures than columbium and tantalum but show a marked sensitivity of transition temperature to structure as well.' Recrystallized materials become brittle at considerably higher temperatures than is the case with material having a worked or fibered micro-structure. Evidence of structure sensitivity has also been detected in columbium- and tantalum-base alloys containing appreciable amounts of molybdenum or tungsten such as F-48 (Cb-15W-5Mo-1Zr) and Ta-10w.2 This paper describes the results of research conducted to further evaluate the effects of metal. lurgical structure on the low-temperature tensile and notch-tensile properties of molybdenum and Mo-0.5Ti. The effects of rolling reduction, stress-relief annealing temperature, and recrystallized grain size were studied. Considerable progress has been made in explaining the fundamental mechanisms of the flow and fracture characteristics of bcc metals. Several of these concepts are helpful in interpreting the data obtained in this study. Brittle fractures occur when the highly temperature-sensitive yield strength equals, or exceeds, the temperature-insensitive brittle cleavage fracture stress.3 The rapid increase in yield strength with decreasing temperature, characteristic of all bcc metals, is therefore of primary concern. petch4 has described the yield strength, ay, (stress required to initiate plastic flow) of bcc metals by the expression where ai is the frictional resistance to slip, Ky is a constant numerically equal to the slope of a a vs curve, and 2d is the average grain diamefer. The oi term itself is thought to be composed of a temperature-insensitive component dependent on impurity content and second-phase particles and a temperature-sensitive component dependent on the Pierls-Nabarro force.5 This equation has also been demonstrated to hold for the flow stress (stress required to maintain continued plastic flow).' Brittle-crack nucleation is thought to occur by the coalescence of dislocations piled up in slip planes at sessile dislocations or twin and grain boundaries.7,8 These proposed mechanisms require that a large number of dislocations be released into the active slip planes so that sufficiently large stress concentrations are produced at the dislocation pile-ups to enable coalescence into a micro-crack. Therefore, at least a microscopic amount of slip must occur in some grains to facilitate initial crack formation. Cottrell 7 has predicted that brittle fracture, nucleated by slip, should occur when where ty is the shear yield strength, ß = 1 in un- notched xension, u is the shear modulus, and y is the effective surface energy. This equation incorporates the Griffith concept of fracture that a crack will propagate if the decrease in strain energy equals or exceeds the increase in surface energy.

Jan 1, 1964

By D. O. Ehrenburg, R. J. Watson

During the earlier period of electrical prospecting, the search for orebodies was by far the most important application of this method of geophysical prospecting. In the past few years, however, increasing attention has been paid to the possibilities of this method in the investigation of subsurface structures. Not only have fault zones been located, but attempts have been made to determine the depth to certain strata and thus contouring on some bed which proves to be a good "electrical marker." Many workers have published the results of field tests showing how their particular interpretations have agreed with the actual field conditions, but very few have stated their method of interpretation. Weaver, Hummel and Stefanesco and Schlumbergerl have given a more theoretical discussion of the resistivity methods. Hummel and Stefan-esco and Schlumberger have published mathematical solutions for the flow of electricity in a medium involving four layers. In this paper the authors present a solution for the flow of electricity in a medium of any number of horizontal strata. By means of this solution, curves showing the relationship between the apparent resistivity and the electrode spacing can be computed for ideal cases. Point-source in an Infinite Homogeneous Medium In resistivity measurements the current is conveyed to the earth by means of two electrodes, which can be mathematically treated as point-sources of equal and opposite strength. A point-source of strength I is defined as a point at which electricity is being generated at the constant rate of I coulombs per second, or I

Jan 1, 1932

By Max Barber

PRESENT equipment and practices in open-pit mines of the Lake Superior iron ranges have been described recently in some detail by A. H. Hubbell.1 It is anticipated that any further improvements will be the result of gradual evolution of present methods and equipment, just as those now used have been gradually evolved from earlier methods. An exception to the process of gradual evolution during the last decade has been the adoption of electric power for operating shovels and trains in open-pit mines, but it is not expected that any such revolutionary changes will be made in the future. The use of Diesel, engine equipment will gain considerable headway, no doubt, and will find favor in certain lines of operation as improvements and adaptations are evolved to meet particular requirements. The question of installing belt conveyors for handling material from deep mines of restricted area, where haulage grades become a serious consideration, or even for transferring earth, rock, or ore material for distances of several miles, is now being studied and some very interesting data are being obtained.

Jan 1, 1932

By Carl H. Beal

DURING the latter part of 1915 and the first half of 1916, the writer held the position of geologist in connection with the conservation work instituted by the U. S. Bureau of Mines, on oil and gas land belonging to the Indians of the Five Civilized Tribes in Oklahoma. The duty of the geologist was to correlate formations containing oil, gas, and water, and to determine the relations of these substances in the different formations so that the conservation agents might carry on their work most intelligently. On account of the rapid development of the Cushing field, which lies in the western part of the Creek Nation, much work was done there by the inspection force. In the course of the geologic studies a large amount of information was collected, which, on analysis, has disclosed some interesting facts worthy of publication. The report, of which the following remarks are an abstract, has been prepared and submitted to the U. S. Geological Survey for publication. This report is now (June, 1917) in the press and will doubtless be issued in a few weeks. Methods Used In addition to the structure maps showing the folding of the Pawhuska limestone, which crops out in several places in the Cushing field, separate structure maps of the three most important productive sands—the Lay-ton (Fig. 2)) Wheeler, and Bartlesville—have been prepared. These structure maps were prepared by obtaining the logs of nearly all the wells

Jan 1, 1918

By P. Payson

Intergranular corrosion in corrosion-resistant chromium-nickel steels has been widely discussed in the last few years. So far as the author knows, nothing has been published which definitely shows that this tendency can be eliminated, although suggestions have been made that a remedy is possible if certain specifications are satisfied. Strauss, Schottky and Hinnüberl suggested an increase in chromium content to an extent that would prevent the impoverishment of chromium on carbide precipitation sufficient to cause impaired corrosion resistance in the matrix. Pilling2 suggested an increase in nickel, so that the stability of the austenite matrix would be increased. Aborn and Bain3 say that "intergranular attack—may be eliminated by preventing carbide precipitation (e. g., by lowering the carbon content or somehow raising its solubility) or by precipitating it permanently under conditions which will not remove chromium from solid solution so drastically at any points." In a later paper Aborn and Bain4 state that many different metallic elements, tungsten, vanadium, copper, aluminum, molybdenum, titanium and zirconium, have been added in small percentages to increase the stability of these alloys, but that it has been reported that according to the copper sulfate test these added elements act only to retard the intergranular corrosion. and that increased nickel and chromium contents have similar effects. Newell5 showed that the lower the quenching temperature before reheating, the less severe was the intergranular attack.

Jan 1, 1932

By Joseph T. Singwald

INTRODUCTION THE purpose of this chapter is to present the diagnostic features (geologic, mineralogic, chemical, and physical) of the principal types of hypogene ore deposits recognized in current genetic classifications, and to classify the ore deposits of the western United States into those types. The genetic divisions used and the criteria determining them are essentially those followed by Lindgren in his Mineral Deposits. Deviations from Lindgren represent either changed conceptions since 1928 (the date of the third edition of Mineral Deposits) due to advance in knowledge or the inevitable differences of opinion between experts in active fields of investigation. Though nineteen economic geologists have been given free hand in presenting their particular topics, there are no fundamental departures in the chapter from the principles set forth by Lindgren. It would be entirely beyond the capacity of a single chapter to give a comprehensive geologic description of all the ore deposits of the western United States. Descriptions of individual deposits have been restricted to those features that are of most diagnostic genetic value. All of the more important deposits receive that much attention. Deposits of lesser economic importance and those inadequately known geologically are treated more briefly or merely cited under what seems to be their proper genetic assignment. The geographic limits of the descriptive matter are the Black Hills and the United States between the Rocky Mountains and the pacific Coast. Capacity of the chapter has made it necessary to impose these geographic limits.

Jan 1, 1933

By J. B. Rather

THE use of sulfuric acid in refining illuminating oils antedates the beginning of the petroleum industry in America by many years. It was used as early as 1792 by Tower in refining "coal oil" in the British Isles, and by 1860 there were 53 refineries in the United States manufacturing "coal oil," most of them using sulfuric acid as a refining agent. Following the completion of the Drake well in 1859, many of the "coal oil" refiners began to use petroleum for manufacturing illuminating oil, and their methods and equipment were adapted so far as possible to this new raw material. The value of sulfuric acid in refining "coal oil" having been established, this reagent was immediately tried and found to be satisfactory in refining petroleum. Notwithstanding the tremendous advances in petroleum technology since that time, sulfuric acid remains today the most valuable and most widely used means for refining petroleum products. EARLY METHODS OF DISPOSAL OF ACID SLUDGE With the almost immediate expansion of the petroleum industry came the problem of disposing of the acid sludge produced in the refining operations. While in 1859, the year of the discovery of the Drake well, a patent was granted for sludge separation and separated acid concentration, most of the earlier refiners, and many of their successors, felt that separation and recovery of spent acid was uneconomical. Accordingly, many of them disposed of the sludge in any way that seemed expedient at the time. It was buried in the refinery grounds, barged and dumped at sea, run into neighboring streams, or dumped into sewers. Some optimists carted it to open pits in the hope that it would either sink into the ground or evaporate. Not so many years ago, the superintendent of an eastern refinery, who was using the open-pit method of disposal, lost a sludge cart, with horse attached, in such a pit. The horse was recovered almost immediately, but its availability for further use was reduced to zero by the loss of its hair.

Jan 1, 1928

By Ganesh P. Mohanty, James J. Wert

THE brittleness of the intermetallics usually render their deformation studies at ordinary temperatures using conventional techniques inadequate. On the other hand, although X-ray line broadening measurements is not a complementary technique, it provides a means for gaining limited but useful information on the cold worked state of these materials. In the present instance, a study of the effects of cold work in the lead telluride intermetallic compound was carried out by analyzing the diffraction profiles of the deformed and the corresponding annealed samples. An ingot of PbTe was prepared by induction melting high-purity lead and tellurium in a quartz crucible under an atmosphere of argon. After homo-genization, the ingot was ground to -325 mesh at room temperature, and using a polished die the cold- worked powder was pressed into the form of flat faced briquets for diffraction measurements. A spectrometer with 0.125 deg per min scanning velocity, CuKa radiation, pulse height analyzer, and a proportional counter were employed in the X-ray measurements, and the powder peaks were collected from the sample in fully cold-worked state and after it had been annealed to relieve the effects of cold work completely. For reliable estimates of the peak extremities, small angular ranges where the tails merged into the background were point counted. Fourier inversions of the experimental peaks were carried out in an IBM 705 computer using the procedures introduced by stokes.' Both the cosine and sine components of the Fourier series were used to take into account any peak assymetry arising

Jan 1, 1963

By C. H. Samans, G. F. Tisinai, J. K. Stanley

The addition of nitrogen (0.10 to 0.20 pct) to Fe-Cr-Ni alloys of simulated commercial purity results in a real displacement of the u phase boundaries to higher chromium contents. The effect is small for the (Y + s)? boundary, but is pronounced for the (y + a +s)/(y + a) boundary. Although there is an indication of an exceptionally large shift of the n boundaries to higher chromium contents, especially in steels with nitrogen over 0.2 pct, the major portion of this apparent shift results from the fact that carbide and nitride precipitation cause "chromium impoverishment" of the matrices. The effect of combined additions of nitrogen and silicon to the Fe-Cr-Ni phase diagram is demonstrated also. Nitrogen can nullify the effect of about 1 pct Si in shifting the (y + o)/? phase boundary to lower values of chromium at all nickel levels from 8 to 20 pct. NItrogen can nullify this U-forming effect of about 2 pct Si at the 8 pct Ni level, but not at the 20 pct Ni level. The alloys studied were in both the cast and the wrought conditions. There are indications that the u phase forms more slowly in the cast alloys than in the wrought alloys if both are in the completely austenitic state. The presence of 6 ferrite in the cast alloys accelerates the formation of U. Cold working increases the rate of o formation in both cast and wrought alloys. THE major improvement in Fe-Cr-Ni austenitic alloys in recent years has been in the addition or removal of minor alloying elements to facilitate better control of corrosion resistance, sensitization, and heat resistance. One shortcoming of the austenitic Fe-Cr-Ni alloys, which never has been completely circumvented, is their propensity toward u formation. In the AISI-type 310 (25 pct Cr-20 pct Ni) and type 309 (25 pct Cr-12 pct Ni) steels, sufficient amounts of u phase can form, if service or treatment is in a suitable temperature range, to cause severe embrittlement. Also, there is a growing conviction that this phase may be contributory to some unexpected decreases in the corrosion resistance of certain of the 18 pct Cr-8 pct Ni-type steels. The present paper discusses the effect of nitrogen additions on the location of the (r+u)/d and the (y+a+u)/(y+a) phase boundaries in the ternary Fe-Cr-Ni system, for cast and wrought alloys of simulated commercial purity, and in similar alloys containing up to about 2.5 pct Si. The objective is to define compositional limits for alloys which will not be susceptible to u formation when used near 1200°F (650°C). An excellent review of the early studies of the u phase in the Fe-Cr-Ni system has been compiled by Foley.1 Rees, Burns, and Cook2 have determined a high purity phase diagram for the ternary system, whereas Nicholson, Samans, and Shortsleeve3 are- stricted themselves to a portion of the simulated commercial-purity phase diagram. Both groups of investigators show almost an identical position for the commercially significant (y+u)/y phase boundary. Further comparison of the work of the two groups indicates that, below the 8 pct Ni level, the commercial alloys have a decidedly greater propensity toward u formation than the high purity alloys. The two groups of workers agreed that both the AISI-type 310 (25 pct Cr-20 pct Ni) and the type 309 (25 pct Cr-12 pct Ni) steels are well within the (y+~) region and that the 18 pct Cr-8 pct Ni-type alloys straddle the U-forming phase boundaries. Nicholson et al.3 showed, in addition, that these boundaries shift toward lower chromium contents if greater than nominal amounts of silicon or molybdenum are added. The effect of nitrogen on the location of the s phase boundaries in the Fe-Cr-Ni system has not been known with any certainty. In 1942, an approach to this problem was made by Krainer and Leoville-Nowak,' but at that time they apparently were unaware of the slow rate of s formation in strain-free samples and aged their samples for insufficient times, e.g., 100 hr at 650°C (1200°F) and 800°C (1470°F). For this reason, it would be expected that their (y+ u) /y boundary would be shifted toward lower chromium contents (restricted ?-field) when equilibrium conditions were approximated more closely. Procedure for Studying the Alloys The alloys used were prepared in the following way: Heats of 200 lb each were melted in an induction furnace. A 5 lb portion of each heat was poured into a ladle containing an aluminum slug for de-

Jan 1, 1955

By M. J. Blackburn

The ordering reaction and its effect on dislocation awangements in alloys based on Mg3Cd has been studied by transmission electron microscopy. Ordering occurs by the growth of ordered domains until they impinge, thus producing an antiphase domain boundary (APB) network. In the disordered alloy, slip is confined to the basal plane while in the ordered condition slip occurs on the basal, prism, and pyramidal planes. Superdislocations have been identuied on these planes and their origin and expected spacings are discussed and compared with the observations. The APBs between the dislocation pairs have been resolved and have proved useful in the identification of superdislocations. Observed slip structures are related to the changes in mechanical properties produced by ordering. At high temperatures magnesium and cadmium form a continuous series of disordered hexagonal solid solutions. At lower temperatures three ordering reactions occur; two based on the compositions Mg3Cd and MgCd3 are transformations to DO19-type superlattices while alloys based on the composition MgCd transform to a B19 lattice. The ordering process in alloys near the composition Mg3Cd has been studied by several workers'-4 and it has been shown to be a first-order type transformation. The variation of mechanical properties with the degree of order and temperature have been reported in some detail by Stoloff and Davies.5 It was shown that the disordered alloy was stronger and less ductile than the ordered alloy, the differences being attributed to changes in the number of active slip planes and to the presence of short-range order in the disordered alloy. In this investigation the ordering reaction has been qualitatively followed by transmission electron microscopy. The effect of this ordering transformation on the dislocation arrangements in deformed specimens has been studied in some detail. EXPERIMENTAL Alloys were melted in a stainless-steel crucible under a flux and chill cast; both melting and casting were performed in an argon atmosphere. The ingots were hot-rolled and tensile specimens cut from the resultant strips. Some large-grained specimens were grown by the strain-anneal method. Heat treatment was carried out in inert atmosphere furnaces and in oil baths at the lower temperatures. Thin foils for transmission electron microscopy were produced by electropolishing in a cooled solution (temp = -40°C) containing 50 cu cm of nitric acid and 180 cu cm of methanol at a potential of 10 v. The ordering reaction was followed by transmission electron microscopy, X-ray, and electrical resistivity measurements but this paper will be concerned chiefly with the electron-microscopy results. Much of the work described in this paper was performed on an alloy containing 26.10 at. pct Cd although two of the micrographs are taken from work on a 25.55 at. pct Cd alloy. RESULTS i) The Quenched Solid Solution. Specimens which were quenched from above the critical temperature showed diffuse superlattice reflections. sark-field analysis on these reflections failed to reveal the presence of ordered domains and thus the superlattice reflections were assumed to arise from regions of short-range order. Quenching from temperatures of 400" to 450°C results in the formation of dislocation loops and helical dislocations. Such defects have been observed and analyzed in detail in several hexagonal metals6-' and as the crystallography and interactions of such loops appear similar in this alloy they will not be reported in detail. Fig. 1 shows a high density of loops

Jan 1, 1968

By T. O. King, Y. P. Gupta

The self-diffusion of sodium in two sodium silicate liquids was measured in the temperature range 850" to 1500°C by the capillary-reservoir technique. Radioactive Na 22 was used as the tracer. The total count and autoradiographic methods were used for determination of the total Na 22 depletion and diffusion profiles of the dqy-used specimens. The diffusion coefficients obtained by the autoradiographic technique are slightly smaller than those obtained by a total count method. Error analysis of the two methods suggests that more confidence be placed in the results of the total count method. The experimental results were analyzed in terms of the existing activated rate process theory. The activation energy for diffusion was shown to decrease markedly as the temperature increased. This was attributed to a variation in the heat of activation with temperature, probably related to a change in the distribution of anions associated wilh the cation. In terms of a model, suggested for diffusion in liquid silicates, differences in the aclivation energies for diffusion and electrical conduction may arise from the effect of the electric field applied in conduction measurements. It is generally accepted that liquid silicates consist of cations and an equilibrium distribution of complex anions determined by temperature and composition. Transport properties in molten silicates are of interest, not merely because of their relevance to the kinetics of pyrometallurgical reactions and glassmak-ing processes, but also because they are useful to development of the theory of such ionic liquids. Self-diffusion is one such transport process that may, if studied for liquid silicates of widely varying compositions, indicate structural changes through changes in the activation energy for diffusion. The self-diffusion of calcium, silicon,' sulfur: aluminum, 4 and oxygenS in lime-alumina-silica melts and of iron6 in molten iron silicates have been measured. Unfortunately, the errors in some of the reported activation energies for diffusion are too large to allow firm conclusions concerning structure and the mechanism of the diffusion process to be drawn. The research reported here was a study of the self-diffusion of sodium in liquid sodium silicates. The soda-silica system was chosen since: i) a reasonable composition range can be covered in the binary system at moderate temperatures; ii) suitable isotopes of sodium (radioactive Na 22 and NaZ4) can be obtained; iii) data on the electrical conductivity and viscosity of sodium silicate liquids are available. However, the range of composition actually used in diffusion experiments was limited, to 20 to 35 wt pct soda, by the relatively high viscosity of silica-rich compositions and by evaporation of soda from basic melts. EXPERIMENTAL PROCEDURE The capillary-reservoir technique was used, wherein a radioactive tracer, Na 22, incorporated in the capillary melt, was allowed to diffuse out of the platinum capillary tube into a large reservoir of silicate liquid containing a chemically identical melt, but without radioactive tracer. After a specific diffusion time, both the total depletion in the tracer concentration and concentration-distance profiles of the diffused samples were measured by procedures to be described later. The diffusion cell assembly was similar to that used by Koros and King.' The temperature of the diffusion cell was measured with a calibrated Pt, Pt-10 pct Rh thermocouple located at the center of the liquid reservoir. The same thermocouple was used to obtain the temperature profile in the reservoir. The temperature at the top of the reservoir was slightly higher (2°C) than that at the bottom, to minimize convection in the capillary tubes, which were placed, open end up, in the reservoir. Convection was not expected to be a problem since the length-to-diameter ratio of the tubes was about 12:1 and the maximum capillary diameter was 1 mm. The diffusion cell was heated in a molybdenum-wire resistance furnace, previously used by Koros and King, but somewhat modified. A Pt, Pt-10 pct Rh thermocouple enclosed in an alumina tube and located near the furnace winding was used in conjunction with a preamplifier and Micromax proportional controller for temperature control, within 4°C, at temperatures near 1500°C. Before starting a diffusion run, the furnace was heated to the desired temperature and an alumina guide assembly for the capillaries was slowly lowered to within 2 cm of the liquid reservoir. The capillaries were thus heated to about the temperature of the bath. The run was started by lowering the assembly till the open ends of the capillaries were about 1 cm below the surface of the liquid. The run was ended by raising the assembly to about 15 cm above the liquid bath. Later, the sample assembly was slowly withdrawn from the furnace. Six diffusion samples were usually run at the same time. Three runs made with the open ends of the capillaries down were discarded because in the majority of these samples air bubbles trapped at the open end were observed. Some glass adhered to the outside of the capillary on withdrawal. This was carefully removed and used to check that the Na 22 activity in the sink remained at a low level. Materials. Nonradioactive sodium silicates were prepared by melting, in a platinum crucible, weighed quantities of sodium carbonate and powdered silica. To prepare radioactive sodium silicates, Na2 obtained in HC1 solution, was first checked for radioactive impurities by obtaining a y-ray energy spectrum, then the chloride ions were removed by anion-ex-

Jan 1, 1968

By Clarence E. Sims, Donald W. Williams, George A. Moore

INTRODUCTION DURING the past several years, the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture, and the ductility values can often be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging. The cure of such an abnormal condition represents a real improvement in the quality of the steel, Several types of abnormal loss of ductility can be distinguished, of which those caused by excessive amounts of inclusions of undesirable type and those caused by unsuitable grain size and ingot structure are well known. The particular type of abnormal lowered ductility currently under consideration may be distinguished by the fact that the low-temperature aging treatment necessary for its relief is insufficient to cause any visible change in the microstructure as ordinarily observed. As this aging will in fact eventually occur at room temperature, the phenomenon of present interest may be given the symptomatic definition, "Temporary Abnormal Low Ductility." Some hundreds of previous investigations, largely qualitative in nature, have established, beyond reasonable doubt, that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary abnormal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen-, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, The Steel Founders' Society of America has, since Nov. 1, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. The interest of this investigation thus extends to permanent abnormal losses of ductility, such as are caused by the inclusions which sometimes result from special deoxidizing practices and possibly from metallic nitrides, but as these can be distinguished from the temporary effect of hydrogen, they have been excluded from the work reported here except when they

Jan 1, 1948

IT is necessary that all men who wish to bring things to a certain end should think of the agents needed to attain this. Now whichever one of the above processes you wish to use you must consider the nature of the material and see whether it is disposed to render what you wish to extract. Then you must see whether you have the other agents sufficiently powerful and proportioned to attain this result, for if the things were not in harmony your work would be vain and very laborious. Therefore, if you should wish to make waters or oils by way of distilla-

Jan 1, 1942

By Axel Hultgren, B. Herrlander

THE original aim of the present investigation was to study the mechanism of cracking on hot-deforming red-short steels. During the microscopical examination of hot-deformed soft steels attention was directed to various patterns of so-called veining in the ferrite, as related to variations in the deformation procedure and the heat-treatment of the steels. Later, a hot-short steel of higher carbon content was also studied. Historical Storey1 suggested in 1914 that veining developed during the gamma-alpha transformation from the growing together of several alpha nuclei within the same gamma grain. Rawdon and Berglund2 found that in soft steel, forged somewhat below A3, the ferrite showed profuse veining, while usually there was very little veining after forging at very high temperatures. They emphasized the similarity between the pattern of veining formed by deformation about 600°C and that of slip lines formed by deformation at room temperature. They also suggested a relation between the gamma-alpha transformation and veining. They became convinced from etching and from the slip-line pattern in cold-deformed material, that the orientation within any ferrite grain showing veining was uniform. In recrystallized alpha grains veining was absent. Veining did not appear materially to affect the properties of ferrite. Independent of veining, continuous networks, attributed to preexisting delta and gamma grain boundaries were sometimes found, the former only in cast steel. Those networks were usually connected with small inclusions. Ammermann and Kornfeld3 confirmed that recrystallized ferrite grains showed no veining. In soft steel annealed between At and A3 there was veining only in the ferrite grains formed during cooling. Electrolytic iron deformed at 880° was free from veining. Bannister and Jones4 considered veining in ferrite to be a manifestation of microscopical and submicroscopical inclusions. Northcott,5,6 in studies on veining in steel and other metals and alloys, attributed veining to oxide inclusions. It could generally be removed by annealing in hydrogen, a suggestion earlier made by Rawdon and Berglund. Tritton (discussion in ref. 5) emphasized the importance of perfect polishing for bringing out veining by etching, and thought the veins or subboundaries were produced during the gamma-alpha transformation, when it was rapid, as a result of the volume change and contraction during cooling.

Jan 1, 1946

By John Birkinbine

IN the spring of 1878 the Pine Grove Furnace, located in Cumberland County, Pa., was blown in after lying idle for several years. The furnace was constructed in 1770, and for over a century it has been in almost continual operation. The plant consisted in 1877, when the writer was first called there, of a stone stack 32 feet in height, inclosing a shaft and boshes, the latter being 8 feet in diameter. The blast was supplied by two wooden blowing-tubs discharging into a third, having a floating piston sustaining a box weighted to give the desired pressure, the power being furnished by a waterwheel. A small 18-pipe hot-blast stove heated the blast. The furnace was remodelled during the winter of '77-78, and a Weimer blowing-engine with a blowing-tub 5 feet in diameter and 2 feet stroke, and the necessary boilers, were substituted for the wooden tubs and water-wheel. The stack was raised and enlarged, and provided with a bell and hopper having a central drop. Water dam and tymp were added, and general repairs were made. The hot oven, however, was riot increased. The furnace had always been operated with charcoal as fuel, and its reconstruction was made with a view to continue the use of charcoal, but provision was made for ample blowing capacity should other fuels at any time be employed. Although liberal arrangements had been made in cutting wood, the stock of charcoal supplied in 1878 was insufficient for the increased requirements of the remodelled plant, and notwithstanding the purchase of some 80,000 bushels from an adjacent idle furnace, there was riot enough to keep the furnace in constant blast until a new supply could be obtained, particularly as the season was unusually backward. Instead of following the established precedent of many charcoal furnace managers, i. e., blow out every February, it was determined to continue in blast, using coke as fuel. Accordingly, when the charcoal stock was exhausted, on March 22d, 1879, Connellsville coke was substituted, the change of fuel being made at once; that is, the coke charges followed immediately upon the last charcoal charges. After working a few days,-the strike in the Connellsville coke region cut off the supply, and anthracite coal was obtained, a mixture of the two fuels being employed. The strike continuing,

Jan 1, 1880