Search Documents

By Carl Samans

THE attention of physicists and metallurgists has been directed toward the study and explanation of the deformation textures in metals for the past 15 years. In 1920 N. Uspenski and S. Konobejewski1 were first able to show that the symmetrical X-ray diffraction effects that had been previously reported by E. Hupka2 and others in metal foils were caused by a directed arrangement of the crystallites. Since then, the systematic study of textures resulting from the application of the pure forces of tension or compression to polycrystalline materials hag been supple-mented by many investigations on deformed single crystals, which have greatly added to our knowledge of deformation. However, despite the valuable information secured from these comparative studies only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature. This lack of quantita-tive data is especially unfortunate because of the much greater practical significance of rolling textures and their effects in both cold-rolled and annealed materials. This investigation was undertaken for the purpose of specifying the deformation of rolled single crystals in the hope that such information might later facilitate the explanation of polycrystal-line textures.

Jan 1, 1934

By G. R. Speich, L. Zwell, H. A. Wriedt

HORNBOGEN1 has recently shown that it is possible to measure the degree of segregation accompanying cellular precipitation in ferritic Fe-Zn alloys by measuring the lattice parameter of the ferrite phase within the cell. In extending this work to study a wider range of composition and to evaluate the free-energy change accompanying the growth of the cells, the lattice parameter and the boundary of the a! phase in Fe-Zn alloys were redetermined to check the earlier work of Schramm.2 This appeared to be necessary since the Fe-Zn diagram has been drastically revised since the work of Schramm. Stadelmaier and Bridgers3 have recently shown that, contrary to prior belief: the y iron field is closed and the a phase boundary extends to an a + T + L peritectic at 782°C where peritectic a contains 42 at, pet Zn. The phase T in equilibrium with the a solid solution has a composition near Fe3Zn10 and a cubic 081 type structure.' The alloys were prepared by two different methods. In the first method carbonyl iron powder (400 mesh, 99.8 pet pure) and high-purity zinc powder (200 mesh, 99.99 pet pure) were mixed in a ball mill and then pressed in a die at 40,000 psi pressure to make compacts with a diameter of 5/8 in. and a thickness of l/4 in. These were sealed in evacuated quartz capsules, gradually heated to 1100°C over a period of 1 week (3 days at 600°C) 3 days at 800°C, 1 day at (1100°C), and then quenched in iced brine. For the alloys containing 23.4 and 30.1 at. pet Zn, the final homogenization anneals were performed at 1000" and 850°C) respectively, to prevent melting. In the second method, alloys were prepared by saturating high-purity iron millings (0.001 in. thick, 99.9 pet pure) in zinc vapor. For each alloy the impregnation was conducted at a fixed vapor pressure of zinc and a fixed temperature between 750' and 800°C. When saturated, the millings were quenched in water. The compositions of the alloys prepared by both methods are shown in Table I. The lattice parameters of the ferritic solid solutions were determined by comparing the 26 values of their 310, peaks (using Co Ka) or of their 211 , peaks (using Cr Ka) with those of corresponding peaks for high-purity a iron. The 20 values were measured at room temperature with an X-ray dif-fractometer (G.E.-XRD5). By using a fiducial value of 2.8664Å for the lattice parameter of pure a iron at 25oC,5 the lattice parameters of the zinc-bearing

Jan 1, 1964

By P. T. Carter, A. B. Murad, H. B. Bell

The distribution of manganese and oxygen between molten iron and FeO-MnO-SiO2 slags not saturated with SiO2 has been determined and used to calculate activities of MnO and SiO2 in MnO-SiO2 slags. These were found to be intermediate between the corresponding activities in FeO-SiO2 and CaO-SiO2 slags. THE equilibrium constant for the reaction between molten iron containing manganese and slags containing FeO and MnO, namely: FeO(slag) + Mn = MnO (slag) + Fe(1iquid) is most conveniently represented by: (MnO) Kmn== (FeOHMn] [Fe] is omitted, since for dilute solutions of manganese in iron, afe is approximately constant. When activities are used for (MnO), (FeO) and [Mn], Kmn is a true equilibrium constant and will apply to all types of slags, but when weight percentages are used, the values obtained for Kmn for different slags vary considerably. The equilibrium between iron containing manganese and relatively pure FeO-MnO slags has been investigated by several workers;1-4 the most recent investigation reported is that of Chipman, Gero, and Winkler.4 Their results, corresponding to slags containing up to 4 pct SiO2, were represented by the equation: 6440 log KMn = +2.95 In this case both slag and metal may be assumed to be ideal solutions, therefore the values of Kmn so derived represent the true constant for the manganese reaction. As the molecular weights of MnO and FeO are almost equal, weight concentration of these oxides may also be used in the above expression. Acidic oxides such as SiO2 and P2O5 affect the activities of FeO and MnO differently, so that when total concentrations by weight of FeO and MnO are used in the above expression for Kmn the values obtained are no longer constant. These will be denoted by K'mn. Körber and Oelsen5 investigated the manganese reaction using silica-saturated iron-manganese-silicate slags and found: 7940 logK'mn =3.172 This corresponds to Kmn values much higher than those obtained for pure oxide slags. The results of Körber and Oelsen, and Chipman, Gero, and Winkler are summarized in Table I. In the present investigation it was decided to study the manganese reaction using iron-manganese-silicate slags not saturated with silica, and which fell mainly between the orthosilicate join 2FeO . SiO2 - 2MnO.SiO2 and the FeO-MnO side of the ternary system FeO-MnO-SiO2. It has been shown" that the phases present in solidified slags of this part of the diagram are (FeO, MnO) and (2Fe0.Si02, 2Mn0-SiO,) solid solutions. Such an investigation would be of interest in deoxidation and also gives information on activities in liquid slags. This equilibrium has not as yet been investigated successfully. Hilty and Crafts7 attempted to examine this reaction in a rotating crucible furnace, but were unable to obtain suitable slag samples. In the present investigation one series of experiments was carried out in a rotating crucible furnace, because the success of Taylor and Chipman8 with such a furnace in their study of oxygen distribution between molten iron and (CaO, MgO) — FeO-Si0, slags suggested that it would minimize contamination of the slag by the crucible material. A second series was carried out using a wire-wound resistance furnace. Rotating Crucible Furnace Experiments In all cases the metallic charge consisted of 800 to 1000 g Armco iron containing 0.02 pct C, 0.03 pct Mn, and traces of Si. Manganese and silicon additions consisted of electrolytic manganese (99.9 pct)

Jan 1, 1953

By R. F. Lynch, J. D. Wood

The Al-1.0 pct Mg alloy 565 7 was studied using optical microscopy and electron microprobe X-ray analysis. Constituent particles were found to exist inter-dendritically in the as-cast material in a region of precipitate free a -aluminum. Five phases besides a fine precipitate and a-Al were identified in the cast structure: Fel3, Fe2Al7, Mg2Al3, CUMgAl2, and Cu2FeAl7. Thermal treatments conducted for 100 hr at 1180°, 1130°, 1080°, 1030°, 980°, and 880° F revealed a general dissolution and spheroidization of the in-terdendritic constituent network observed in the cast structure. The principal constituents present in the thermally treated structures were FeAl3 and Fe2Al7 with the relative amount of Fe2A17 to FeAl3 increasing with a decrease in the treatment temperature. The phases Present in the wrought structure were identical to those observed after the thermal treatments, with the constituent particles strung out in the direction of rolling. ALLOY 5657 is a nonheat-treatable commercial purity Al-1.0 pct Mg alloy utilized extensively because of its bright finishing characteristics. This investigation was conducted to determine the constituents present in 5657 alloy, and to study the effect of extended thermal treatments on morphology. Numerous studies have been carried out to establish the equilibrium diagrams for various aluminum systems,1-3 with phase identification based on X-ray analysis, morphology, and the etching response of relatively large particles. Phragmen4 conducted a study of the phases in aluminum eutectic systems and compiled a "corrected" table of etching responses, drawing on his work plus that of Schrader,5 Keller and Wilcox,6 and Mondolfo.7 A review of the original work of Keller and Wilcox, and Mondolfo, which was concerned with the constituents found in commercial alloys, reveals that in numerous cases their etching responses differ from those reported by Phragmen and from each other. These inconsistencies may occur because a specific constituent will react to a given etch in a varying manner depending upon its size, the elements dissolved in the phase, the other constituents surrounding a phase, and the solute content of the matrix. Work with a commercial orientation was conducted on alloys 2024 and 3003 by Sperry8,9 and on alloy 3003 by Barker,10 where the relationship between the phase diagram and the nonequilibrium structure of an alloy was examined. Backerud11 investigated the A1-Fe binary system and found that at high cooling rates the equilibrium eutectic reaction forming a-A1 and FeA13 is replaced by another lower temperature eutectic reaction forming a-A1 and metastable FeAl6, a constituent first identified by Hollingsworth et al.12 Most of the above mentioned studies were conducted on materials having a significantly greater alloy content than 5657 alloy, where the relatively small size and sparse distribution of second phase particles hinders the process of identifying constituents. EXPERIMENTAL PROCEDURE Material with a composition as given in Table I was examined in the as-direct chill cast, hot rolled and cold rolled conditions, and after thermal treatment of the cast structure. Thermal treatments were terminated by a water quench. Microscopic examination was conducted under various lighting conditions following the application of standard etchants as specified in Table 11. A semi-quantitative electron microprobe X-ray analysis was conducted for Al, Mg, Fe, Cu, Si, Zn, and Ti. RESULTS AND DISCUSSION Microstructure of the As-Cast Material. Particles of second phase material were found to exist inter-dendritically, principally in regions of precipitate free a-Al, as illustrated in Fig. 1. Adjacent to the ingot edge was a region of inverse segregation, resulting in an increased amount of second phase material containing large sized particles which aided in phase identification. Phase Identification. Cast Structure. Five phases besides a-Al and a fine precipitate were identified using optical microscopy and electron microprobe X-ray analysis, as presented in Tables II and III, respectively. FeA13 and Fe2A17 are often found with Fe2A17 forming a sheath around the core of FeAl3, resulting from an incomplete peritectoid reaction. These phases have a nearly identical appearance under white light, although they are easily differentiated under crossed polarizers, as characteristically illustrated in Figs. 2(a) and 2(b), respectively. Microprobe analysis con-

Jan 1, 1970

By Ashok K. Sinha

The quasi-binary systems "VFe3"—VCo,—VNi,— "VCu3"and "TiFe3"—TiCo3,—TiNi3-"TiCu3"have been studied by a combination of microscopic and X-ray methods. Of the Phases encountered, eleven had close-packed ordered layer structures. Within each system, there is an approximately linear variation of the degree of hexagonality of the stacking arrangement with electron concentration, e/a. A study of eighty -four known examples of AB3 structures in transition metal alloys indicates that at e/a = 8.65 the ordered structure of the close -packed layers changes from "triangular" (AuCu3 type) to "rectangular" (SbCu3 type). At e/a < 8.65, the slope of hexagonality us e/a line increases with the group number of the A component. An interesting series of close-packed ordered structures is known to exist at the composition AB3; however, their alloy chemistry has not yet been fully understood. Dwight and Beck1 observed a correlation between position of the components in the periodic table and the type of crystal structure of the binary AB2 structures formed by transition metals. No consistent effect due to atomic size was noted and they proposed that electron concentration* predominates in In the present paper, the AB3 structures are characterized by a symbol describing the stacking and a symbol specifying the ordered layer. The stacking symbol used was introduced by Zhdanov,7 and later used in the International Tables,8 and by Beck9 in his survey of possible layer stacking structures. Alternating positive and negative integers are used to represent the number of positive (e.g., in abcabc...) and negative (e.g., in cbacba...) stacking sequences. T denotes the triangular ordering found in close-packed planes of the AuCu3 structure and R the rectangular ordering found in close-packed planes of the SbCu3 structure, Figs. 3(a) and (b). The present structure symbols are listed in Table I alongside the prototypes, where known, and other structural characteristics of AB3 phases found in the present investigation. EXPERIMENTAL The starting materials were metals of 99.9+ purity. The alloys were prepared by arc melting under argon atmosphere using a nonconsumable tungsten electrode and water-cooled copper hearth. The total weight loss upon melting and subsequent annealing was always less than 0.5 pct and hence the alloys will be referred to by their intended (unanalyzed) compositions. The alloys were homogenized and annealed at suitable temperatures in the range 750" to 1200°C, the annealing periods varying from 3 days at 1200°C to 10 days at 750°C. The heat treatments were carried out in sealed silica capsules under argon atmosphere and with a molybdenum foil cover between the alloy and the walls of the capsule. The quenched alloys were microscopically examined and reduced to powder by crushing or filing. The powders were, whenever necessary, given a stress-relieving anneal at the original annealing temperature. X-ray powder patterns were obtained with an asymmetrical focusing camera, a Guinier-deWolff focusing camera, or a Debye-Scherrer camera. Cr, Co, or Cu radiations were used. In some cases, to ensure the minimum degree of contamination, the deeply etched specimens were mounted in the asymmetrical focusing camera to obtain an X-ray pattern. Internal silicon standards were employed for lattice parameter determinations. The intensity calculations were made by using a Fortran IV program

Jan 1, 1970

By J. L. Keats

IN THE literature on the elimination of metalloids in basic open-hearth practice, there are a great many heats recorded in which excellent data on changes in slag and metal composition during refining are given, but in almost all of these heats either temperature data or weights and analysis of charge are unrecorded and observations on the physical characteristics of the slag are almost always lacking. With these points in mind, a test heat was made in which as complete as data possible on all the factors that affect the elimination of metalloids were obtained. THE TEST HEAT The test heat was made in a standard 100 ton stationary furnace at the Lackawanna Steel Co., Lackawanna, N. Y. on January 17, 1922. The Charge-Scrap.-The scrap consisted entirely of rail-heat butts, selected from a number of heats made, the week before the test. The average analysis of the scrap was calculated from the analysis of these heats-and from the weight of scrap from each heat. Pig Iron.-Two ladles of pig iron were used in the charge and two samples were taken from each ladle as it was poured into the furnace. These four samples were composited for the average pig-iron sample.

Jan 2, 1926

By J. P. Morris

PREVIOUS investigations1,2 have shown that alloying elements in liquid iron influence the thermodynamic activity of sulphur and thereby affect the partition of sulphur between metal and slag in the desulphurization process. For example, the greater efficiency of desulphurization in the blast furnace as compared to the open hearth can be attributed in part to a higher level of sulphur activity in blast-furnace metal due to the higher concentration of carbon and silicon. In the present investigation, a short study was made of the influence of manganese on the activity of sulphur in liquid iron and iron-carbon alloys. In contrast to carbon and silicon, manganese was found to decrease the activity coefficient of sulphur; and in iron-carbon alloys it counteracts to some extent the influence of carbon. However, at manganese concentrations normally present in the blast furnace or open hearth, the effect of manganese is small. Since manganese sulphide has a limited solubility in iron, manganese can act, under certain conditions as a desulphurizing agent. Considerable data on the manganese-sulphur product in carbon-saturated melts were obtained in the investigation and have been included in this report. The experimental procedure was the same as that used in the earlier investigations on the effect of silicon&apos; and carbon&apos; on sulphur activity. Briefly, the method was as follows: The molten alloy, contained in a graphite or sintered alumina crucible, was brought to equilibrium at a constant temperature with a mixture of hydrogen and hydrogen sulphide of constant composition by bubbling the gas through the metal. Samples of&apos; the melt were taken for analysis at regular intervals by suction through a 2 to 3 mm bore silica tube dipped into the metal. The experiments were run in a graphite spiral resistance furnace with melts weighing 50 to 60 g. The gas bubbling tubes were made of sintered alumina and were 5/16 in. OD, 1/16 in. ID, and 24 in. long. Equilibrium was assumed to have been attained when the sulphur content of the liquid metal reached a constant value. During an experiment there was a rapid loss of manganese from the melt by volatilization. To offset this loss, small additions of manganese were made periodically. The rate of manganese addition needed to maintain a constant manganese concentration was determined in preliminary tests. In all of the experiments, deposits of manganese sulphide formed above the melts in a cooler region of the furnace. Apparently, these deposits resulted from a reaction between manganese vapor and hydrogen sulphide in the gas. To prove that manganese sulphide did not volatilize from the melts to a measurable extent, an experiment was run in which helium was bubbled through liquid iron containing both manganese and sulphur. Although manganese volatilized rapidly in this test, there was no appreciable loss of sulphur. Volatilization of manganese sulphide from a melt would have led to an apparent equilibrium condition in which the sulphur content of the metal was lower than the true equilibrium value. The experimental results are shown in the first seven columns of Table I. The data in the last two columns were obtained from the previous work on the effect of carbon&apos; and show what the results would have been in the absence of manganese but with temperature, gas composition, and carbon content of the metal remaining the same. Comparison of the last four columns show that, in the presence of manganese, the sulphur content of the metal increased at equilibrium and the activity coefficient of sulphur decreased. However, the results show that, for manganese concentrations below 3 pct, the effect of manganese is small. The values for activity coefficient of sulphur given in Table I were calculated from the following relations: S (in liquid metal) + H2 (gas) = H2S (gas) [l] K ph2s/?s X %S X phg = 0.00251 [2] where K is the equilibrium constant for the reaction, PH2S and ph2 are the partial pressures of hydrogen sulphide and hydrogen, respectively, and ?s is the activity coefficient of sulphur. The standard state for sulphur was taken to be a 1 pct solution of sulphur in pure iron. The numerical value for K at 1600°C was determined in the earlier work. For the purpose of showing graphically the results of the tests run at 1600°C, the activity coefficients of sulphur were recalculated so as to correspond to a manganese concentration in the metal of 2 pct in each case. In the calculation it was assumed that the increase in sulphur content of the metal at equilibrium caused by the presence of manganese

Jan 1, 1953

Undoubtedly other members have given their lives in the Service of the United States and the Allies during the past four years, but the following biographical notices are all that have reached us as yet. Lewis Newton Bailey Lewis Newton Bailey died of pneumonia at Camp Merritt, N. J., Apr. 30, 1918, at the age of 34 years. He was Master Engineer, Senior Grade, in the Fourth Regiment, U. S. Engineers, and although he was offered a commission as First Lieutenant shortly after enlisting, he preferred not to accept it until he had reached France. By those who knew him well, this lack of eagerness for promotion will be recognized as consistent with his whole character. Mr. Bailey was born at San Diego, Cal., May 28,1884, and graduated from the University of California, College of Mines, in 1906. He joined the American Institute of Mining Engineers in 1916. During 1904 he was employed at the cyanide plant of the Buckeye mines, Forest Hills, Cal. In the autumn of 1909 he went to the Coeur d&apos;Alene District, Idaho, and was first employed on construction work of the Bunker Hill & Sullivan Mining & Concentrating Co&apos;., with a short intermission at the Hercules mill, after which. he was sampler and assayer for the Bunker Hill & Sullivan Co. until May, 1910, when he was obliged to return to California to attend to family interests. Returning to the Coeur d&apos;Alene district in November, 1911, he was given charge of remodelling and operating the mill of the Coeur d&apos;Alene Development Co., treating the output of the Ontario mine; this work he performed with credit and complete success. In December, 1914, he returned to the Bunker Hill & Sullivan Co., as assistant metallurgist and mill superintendent, his work consisting mainly in the testing and improvement of concentrator practice, which he continued with great credit until August, 1915, when family considerations required that he again return to the home of his parents at San Diego. Mr. Bailey was characterized by energy, both physical and mental, by devotion to his friends, associates and employer. He was particularly successful in his relations with the men under him and, in fact, was thoroughly well likcd by everybody with whom he came in contact.

Jan 1, 1920

By Roshan B. Bhappu, Milton F. Lewis, Jean A. McAllister

Several alternatives are available for treating lower grade gold ores averaging 0.04 to 0.10 oz per ton. These include heap, vat, and agitation leaching and may involve conventional zinc precipitation or carbon adsorption-electrowinning systems. Each of these processes have their inherent economic and operating advantages and disadvantages and the selection of the optimum method for a given gold ore is solely based on economic evaluation of the applicable processes. In this paper an effort is made to provide engineering feasibility estimates for the above processes under varying operational conditions such as ore grade and price of gold.

Jan 1, 1974

By K. Tanaka, J. D. Mote, J. E. Dorn

It) an attempt to ulLcoce.lP the operative strain-rate-contl-olliy: dislocation nieclzanistns, specially oviented sizgle clystals of the intel-nzediate 1zexagonal phase containing Ag plus 33 at. pct A1 were tested in tension over a wide range of temperatures. Slip was observed to take place by the {0001} <1120> {l100} mechani fracture took place across the(i100) plane and winning occurred by the (i01Z) ?lechanisn. Basal slip exhibited a strong yield point over the -alzge from 77 to 450°K, the upper ,esolved shear st]-ess having the exceptionally high value of 10,500 psi over this entire ?-a?zge of tenzpei,atuves. The critical 9-esolved shear stress for prismatic slip decreased f7-om 48,000 psi at 4.3"K to 23,000 psi at 170°K (Region 1) follozcirg zt:lzich it decl>eased sloz&ly to 21,500 psi at 475°K (Res&apos;on II); from 475" to 575°K (Regioz III), the c7-itical esolced shear stress dec&apos;-eased precipitously to 2000 psi; and from 575" to 750°K (Region IV) it decreased less afi&apos;dly to a low value of about 500 psi. Pvistintic slip in Region I was pobably controlled by the tliel-nally activated riecharzisui of nucleation and g,-ozcth of kinks in dislocations lying in Peierls potential troughs. In Region II for prismatic slip the critical 1-esolved shear stress was slzocn to be deteemined by sh0l.t-range 01-dering, Overall the forgiorz fo basal slip, 7.c.lre1-e a Strong yield-point phenorlienu ia7as observed, the critical vesolved slzea?-stress was shoztn to be determined by n conibirzation 0-f Szizuki locking and short-range-order Izavderzizg, The precipitous decrease in the critical resolved shear stress with increase in ter,/pe7-atrir-e over Region HI was tentatively ascribed to a decrease in the degree of slort-)ange 07-del;iqq (0)- clusteing) and also the effect of fluctuations the degree of o?der, It is at pgreser2t zrtzce)taitz as to 1t1hethe1- these or other possi1)le effects are also ,esponsible. fo- the data obsel-ved 172 Region IV. 1NTEREST in inter metallic compounds stems not only from their role in dispersion hardening of polyphase alloy ystems but equally from their potentialities for high strength, hardness, and stability not only at atmospheric temperatures but especially at elevated temperatures. As summarized in a re- cent symposium of the Electrochemical Society on "Mechanical Properties of Inter metallic Compound", most of the experimental evidence regarding the mechanical behavior of intermetallic compounds centers about the effect of temperature on the hardness and ductility of polycrystalline specimens. The available data reveal that the plastic behavior of intermetallic compounds might be rationalized in terms of the usual dislocation mechanisms appropriate to a solid solutions providing the additional complexities arising from crystal structure, long-range ordering, short-range ordering, and defect lattices are taken into consideration. It is apparent, however, in terms of the history on a solid solutions, that a complete detailed mechanistic rationalization of dislocation processes may not be possible until the deformation processes are studied in single crystals of intermetallic compounds. The present paper contains a preliminary report on the plastic behavior of single crystals of the hexagonal Ag-A1 intermetallic phase over a wide range of temperatures. The results confirm the thesis that single crystal data provide a most effective method of identifying operative dislocation mechanisms in intermetallic compounds. EXPERIMENTAL TECHNIQUES Several factors prompted the selection of the hexagonal Ag-A1 intermetallic phase for this preliminar investigation on the plastic properties of single crystals of intermetallic compounds: 1) This phase has a wide solubility range5 which would permit future investigations on the effect of composition and axial ratios on slip mechanisms. 2) Although it undoubtedly exhibits short-range ordering (or clustering) this intermetallic phase is free from complexities arising from long-range ordering.6 3) Since the atomic radii of aluminum and silver are practically identical, the possible complications due to Cottrell locking are minimized. 4)Whereas the dislocations on the basal planes are expected to dissociate into Shockley partials and are thus susceptible to Suzuki locking, those on the prismatic planes probably remain complete. 5) The axial ratio, being 1.61, is almost ideal, suggesting that short-range ordering may be almost spherically symmetrical. The present investigation was conducted exclusively with the hexagonal Ag-A1 alloy containing 33 at. pct Al. Preliminary investigations revealed that this alloy undergoes basal slip by the (0001)

Jan 1, 1962

By Ernest Lilley

THE tin deposits of Cornwall appear to have been worked for at least 3000 years. Prior to the sixteenth century, the tin came exclusively from alluvial deposits. At that time, shallow pits or mines were started in the hill sections. Mining of copper seems to have begun at the same time, but does not appear to have been especially important until about 1700. From that time until the close of the nineteenth century, copper was of major importance. Lead, and to a lesser extent, other metals, such as antimony, iron and manganese, were produced in commercial quantities during the same period. With the opening of the eighteenth century carne increasing difficulties with water because of the increasing depth of the mines. Among the efforts made to overcome this difficulty was the construction of the "Great County Adit," begun in 1748, taking 20 years to complete, and with its branches having a length of 20 miles. Adits proved capable of handling-only a few of the water problems, and led to rapid adoption of the steam pumping engine in the latter part of the eighteenth century and the early part of the nineteenth. It was in this period that the Cornish pumping engine, still considered by Cornishmen to be the most satis-factory unit for handling large quantities of water, carne into existence. The development of a means of controlling the water made possible the opening up of a number of rich deposits where profitable work-ing was further assisted by numerous improvements in mining and milling machinery. During the middle of the past century, Cornwall, with an average yearly production of 10,000 tons of tin metal and an even slightly larger tonnage of copper, enjoyed a period of unprecedented prosperity. How-ever, the relatively high prices of both copper and tin served not only to encourage prospecting (and much speculation) in Cornwall, but also in other countries. The rapid development of copper mines in the United States, together with sudden impoverishment of the lodes with increasing depth in the greatest of the Cornish copper mines, brought the copper boom to an abrupt end, the production of copper at the close of the cen-tury being negligible in importance and being secured in large measure

Jan 1, 1932

By J. Szekely, V. Stanek

Steady state heat transfer and fluid flow rates are predicted for the counter-current contacting of gas and solid streams. For a .fixed pressure drop across the bed the convective heat transfer rate is affected by the gas flow rate, which in turn is affected by the temperature distribution in the system. Variations in bed voidage and in particle size were found to change the predicted temperature profiles quite markedly, in particular when the thermal capacities of the gas and solid streams were equal. IN Part I we examined the effect of step and pulse changes in the inlet gas temperature on transients in the flow of gases through fixed packed beds. Here we shall discuss heat flow and fluid flow interactions in the counter-current heat exchange between packed solids and a gas stream. Counter-current heat exchange in packed beds has been extensively studied. In his now classical paper, Furnas&apos; assumed constant property values and developed a simple analytical. expression for the temperature profiles in the gas and in the solid stream. A highly sophisticated analysis of counterflow systems, allowing for transients and interparticle conduction was developed by Amundsen. In preparing a very readable review of this topic Elliott&apos; also presented a number of elegant solutions, including the case involving heat generation. A great deal of work has been done on the application of these concepts to the modelling of the blast furnace. However, in all this previous work the mass flow of the gas was regarded as a quantity independent of the gas-solid heat exchange process. In the following we shall consider counter-current heat exchange between a gas stream and a packed bed of solids, under conditions where the pressure drop across the bed is specified, rather than the mass flow of the gas. FORMULATION Consider a packed bed, extending from y&apos; = 0 to y&apos; = L, in which moving solids and a moving gas are contacted in a counterflow arrangement. Let cold solids, with an initial temperature Tsi and mass flow GA, enter at y&apos; = L, and hot gas with an initial temperature of Tgi and mass flow Gg enter at y&apos; = 0. In contrast to the problems considered in Part I this system has a nontrivial steady state and we shall restrict our attention to the study of the pressure drop flow relationships and the resultant temperature distributions for steady state conditions. Under these conditions the formulation of the problem requires the statement of the following: 1) heat balance on the gas 2) heat balance on the solids 3) the mechanical energy balance equation and in addition the knowledge of the equation of state, and a functional relationship between viscosity and temperature and an expression for the heat transfer coefficient in terms of the other parameters. On neglecting temperature gradients within the solids and for a constant mass flow of the gas, the solution to this problem is well known.&apos;" The expressions for the temperature profiles of the gas and solid streams may be put in the following form: where Tg and T, denote the dimensionless gas and solid temperatures respectively, y is a dimensionless distance, and R is the ratio of the thermal masses. These quantities are defined as follows: For the particular case of equal thermal mass capacities by the gas and the solid, that is R = 1, the Eqs. [1]and[2] simplify to Eqs. (71 and[8], respectively: i.e., the resultant profiles are linear. As for most practical cases , solutions given by Eqs. [7] and [8] will contain only the inlet temperatures as parameters. For a fixed, predetermined value of C;b the above

Jan 1, 1970

By George S. Rice

The A.I.M.E. Ground Movement and Subsidence Committee, proposed in 1920, held its first technical meeting in February 1923, under the able chairmanship of Mr. H. G. Moulton. The following list of papers and discussions, indicating the scope of the problems and relation to various conditions and method of mining, were given at that meeting by the distinguished mining engineers: J. Parke Channing, on Subsidence at Miami, Arizona; Howard N. Eavenson, on Mining an Upper Bituminous Seam after a Lower Seam Has Been Extracted; J. J. Rutledge, on Subsidence in Two Oklahoma Coal Mines; Benjamin F. Tillson, on Caving Cracks at the Franklin Mine, New Jersey; Dr. F. W. McNair, on the Dome Theory; William Kelly, on disadvantageous effects in Mining and Back-filling Working Upward a Steep-Pitching Iron-ore Bed; Eli T. Conner, on the good results of Back-Filling by Hydraulic Means in Preventing Destructive Subsidence in the Anthracite District; Thomas H. Claggett, on the merit of Systematic Pillar Drawing in Preventing Cracks in an Upper Seam; Henry H. Otto, successful results in the anthracite district in Mining Lower Seams before Upper Seams; Douglas Bunting, on Leading Factors Incident to Successful Mining of an Overlying Seam; Edwin Ludlow, on there being "less damage to buildings when there was complete removal of coal with complete packing than when room and pillar is used without extracting the pillars"; Edward O&apos;Toole on "bumps" in eastern Kentucky mines, which he thought were the result of geologic stresses: H. A. Buehler, on Upheaval of Surface in an Illinois Case in Advance of the Face; and R. Dawson Hall, on The Mechanics of Subsidence from Mining. The author of this paper discussed various kinds of problems of ground movement and subsidence in both metal mining and coal mining; the production of great landslides by workings near an outcrop, as at Turtle Mountain, Alberta, Canada; and general

Jan 1, 1940

By George S. Rice

The A.I.M.E. Ground Movement and Subsidence Committee, proposed in 1920, held its first technical meeting in February 1923, under the able chairmanship of Mr. H. G. Moulton. The following list of papers and discussions, indicating the scope of the problems and relation to various conditions and method of mining, were given at that meeting by the distinguished mining engineers: J. Parke Channing, on Subsidence at Miami, Arizona; Howard N. Eavenson, on Mining an Upper Bituminous Seam after a Lower Seam Has Been Extracted; J. J. Rutledge, on Subsidence in Two Oklahoma Coal Mines; Benjamin F. Tillson, on Caving Cracks at the Franklin Mine, New Jersey; Dr. F. W. McNair, on the Dome Theory; William Kelly, on disadvantageous effects in Mining and Back-filling Working Upward a Steep-Pitching Iron-ore Bed; Eli T. Conner, on the good results of Back-Filling by Hydraulic Means in Preventing Destructive Subsidence in the Anthracite District; Thomas H. Claggett, on the merit of Systematic Pillar Drawing in Preventing Cracks in an Upper Seam; Henry H. Otto, successful results in the anthracite district in Mining Lower Seams before Upper Seams; Douglas Bunting, on Leading Factors Incident to Successful Mining of an Overlying Seam; Edwin Ludlow, on there being "less damage to buildings when there was complete removal of coal with complete packing than when room and pillar is used without extracting the pillars"; Edward O&apos;Toole on "bumps" in eastern Kentucky mines, which he thought were the result of geologic stresses: H. A. Buehler, on Upheaval of Surface in an Illinois Case in Advance of the Face; and R. Dawson Hall, on The Mechanics of Subsidence from Mining. The author of this paper discussed various kinds of problems of ground movement and subsidence in both metal mining and coal mining; the production of great landslides by workings near an outcrop, as at Turtle Mountain, Alberta, Canada; and general

Jan 1, 1940

By Paul F. Gnirk

INTRODUCTION The notion of permanent disposal of high-level radioactive waste in natural salt formations was formally proposed in 1957 by the Committee on Waste Disposal of the National Academy of Sciences- National Research Council. This proposal was the result of the Committee&apos;s deliberations in response to a request from the U.S. Atomic Energy Commission (AEC) in 1955 to assess the viability of geologic formations for such disposal. The research investigations for waste disposal in salt were initiated at the Oak Ridge National Laboratory (ORNL) in the late 1950&apos;s and continued through the 1960&apos;s and early 1970&apos;s at a relatively modest level of funding. During the period of transfer of Federal Administrative authority from the AEC to the Energy Research and Development Administration (ERDA) to the Department of Energy (DOE) during the latter part of the 197O’s, financial support for the research program was enhanced substantially. The program at OWL was regrouped under the Office of Waste Isolation (OWI) and later transferred to the Office of Nuclear Waste Isolation (ONWI) at Battelle Memorial Institute. With this enhancement in the research program, consideration of basalt, granite, shale, and tuff as repository host media was initiated. In February, 1980 the President of the United States established officially a comprehensive waste management program which called for the selection of the first repository site in 1985 from a suite of four or five potentially suitable sites, and initiation of a repository operation at that site in the mid-1990&apos;s. The current disposal system concept involves the emplacement of radioactive waste packages in mined disposal rooms at depth in suitable geologic formations, with closure of the facility effected

Jan 1, 1983

By P. Greenfield, C. C. Smith, A. M. Taylor

The Mg-Zr alloy ZA and Mg-Mn alloy AM503(S) are shown to have a markedly improved resistance to creep deformation after suitable heat treatments. This improvement makes them suitable for certain stress-bearing fuel element components in nuclear reactors. The extent of strengthening is described and an explanation of the behavior of both materials is given, based on a combination of strain-aging and grain growth. The increase in operating temperatures of fuel element components in Calder Hall type nuclear reactors has necessitated the development of magnesium base alloys with a very high resistance to creep at temperatures up to 500°C. Such alloys are not required for fuel element cans, which require high-creep ductility rather than strength, but for can supporting and stabilizing components, which are needed to support the imposed loads without deforming more than about 1 pct in times of up to 40,000 hr. The amount and type of alloying addition made to magnesium for these parts is limited by the necessity of keeping the cross-section to thermal neutrons as low as possible. The alloys must also possess a high resistance to oxidation in CO2. Alloys which have been developed for this application include ZA, an alloy of magnesium with 0.5 to 0.7 pct Zr and AM503(S), an alloy of magnesium with 0.5 to 0.75 pct Mn. In the as-extruded condition these alloys are very weak and ductile in creep but it has been found that they can be strengthened to a significant extent by heat treatment. This paper describes the method of developing a high-creep resistance in ZA and AM503(S), the extent of the strengthening produced and discusses the probable mechanisms of strengthening. TEST MATERIALS Specimens were taken from typical casts of ZA and AM503(S) alloys extruded into 2 1/4-in.-diam bars, supplied by Magnesium Elektron Ltd. Typical analyses of the bars were as follows: The as-extruded mean grain diameter was 0.001 to 0.002 in. for the ZA alloy and 0.003 in. for the AM503(S) alloy. EXPERIMENTAL METHODS Extruded bars of ZA alloy, 2 1/4 in. in diameter and 9 in. long, were heat treated in electrical resistance furnaces in an atmosphere of flowing CO2 containing 50 to 300 ppm water, thereby reducing the extent of oxidation compared with that which would have occurred in air. Heat treatments were carried out at 600oc for times of 8, 24, 48, 72, and 96 hr and material was subsequently both furnace cooled and water quenched. In order to measure the effect of time of heat treatment, specimens were creep tested at 400°C and 336 psi for about 1000 hr. Subsequently, the behavior of material heat treated for 96 hr at 600°C and furnace cooled was tested at a variety of stresses from 200° to 500°C. Tests were also conducted at 200o and 400°C on material in the as-extruded condition for comparative purposes. With the AM503(S) alloy, only the effect of heat treatment at 565°C for 4 hr was examined. It has been shown1 that such a heat treatment produces marked strengthening in this alloy. Tests on this material were conducted at a variety of stresses at 200°, 300°, and 400oc with comparative tests on as-extruded material at 200o and 400°C. The creep tests were carried out on machines using dead-weight loading and direct micrometer strain measurements on specimens 5 in. long and 0.357 in. diameter. At temperatures of 400° C and below, the creep tests were conducted in air, but at higher temperatures an atmosphere of CO2 was used. Grain size measurements were made on ZA in the extruded and heat treated states and on each specimen after creep testing. This was done by a line count of a minimum of 20 grains in two or three random fields in the longitudinal and transverse directions. The same method was used for measuring the grain size of as-extruded AM503(S), but the grain size of the heat treated material was so large that this method could not be employed. For heat-treated AM503(S) the large grained characteristics (between 0.1 and 1 in.) were confirmed by the measurement of individual grains. In the case of the ZA alloy, specimens taken from various stages in the program were analysed for hydrogen by a combustion method. Material in various states was also analysed for the soluble and insoluble zirconium content by dissolving in dilute hydrochloric acid. This technique has been useda for the determination of amounts of zirconium present

Jan 1, 1962

By Elbert Rowland

THE widespread interest in the alloys of beryllium with copper is due principally to the fact that certain compositions show very favorable precipitation-hardening characteristics and are, in fact, the strongest nonferrous alloys known at the present time. Investigations have been conducted by Masing and Dahl and others on the physical characteristics of ternary beryllium alloys, in an attempt to produce precipitation-hardening effects with a smaller amount of beryllium than that required in the binary copper-beryllium alloys (2.0 to 2.5 per cent Be). The results of these investigations show that ternary alloys of beryllium with Cu-Sn, Cu-Al and Cu-Zn, among others, exhibit promising improvements in physical properties after precipitation-hardening treatment and, while the increases in properties obtained are not as high as those realized from the binary copper-beryllium alloys, excellent properties are obtained with beryllium contents averaging about one-half the amount required in the binary alloys. This paper presents the results of an investigation of the equilibrium relations of certain alloys containing copper, tin and beryllium. The alpha-phase boundary of the ternary system is given for alloys containing from 0 to 1 per cent beryllium. The equilibrium conditions beyond the alpha-phase boundary are presented for alloys containing up to 32 per cent tin and 1 per cent beryllium. The data were collected by means of

Jan 1, 1935

THE increased demand for titanium alloys with improved high-temperature creep strengths has stimulated interest in silicon as an alloying addition to titanium. Silicon is a potent solid-solution strength-ener and, if added in sufficient concentration and properly heat-treated, can also dispersion-strengthen titanium by eutectoid decomposition.&apos; However, better understanding of the nature and distribution of the resulting silicide dispersion in more highly alloyed titanium matrices is necessary for the development of useful titanium alloys which utilize the latter strengthening mechanism. This note describes the chemical and crystallographic characteristics of the silicide phase as it occurs in a typical high-temperature near-a titanium alloy matrix. Several Ti-6A1-3Sn-3Zr a11oys containing various amounts of silicon ranging from 0.1 to 1.0 pct were melted as 10- to 20-lb ingots and processed into 1/2-in.-diam bar stock. The microstructures of specimens annealed at various temperatures were conveniently summarized by the (Ti-6Al-3Sn-3Zr)-Si pseudobinary phase diagram illustrated in Fig. 1. Comparison with the Ti-Si equilibrium diagram indicates the substitutional solutes (Al-Sn-Zr) increase the eutectoid temperature and decrease the a terminal solubility. Annealing at temperatures sufficiently high to dissolve the silicon in a ß solid solution and cooling rapidly enough to preclude coarsening generally produced a uniform dispersion of fine silicide particles, whereas annealing at temperatures near but below the ß transus produced relatively coarse silicide particles. Annealing in the limited a, plus 3 region produced a duplex coarse and fine silicide array. Several a-annealed specimens were examined by X-ray diffraction to determine the crystallographic identity of the precipitate phase. Copper Ka X-ray diffraction patterns of bulk specimens which contained 0.5 and 0.8 pct Si were virtually identical to that of the silicon-free Ti-6Al-3Sn-3Zr base alloy except for a slight shift in some of the high-angle diffraction lines. Apparently the silicide volume fraction was too low to be detected in bulk specimens. X-

Jan 1, 1969

By J. M. Uys, T. B. King

The solubility of water in silicate melts of various compositions was measured. The basicity of the silicate did not appreciably affect the water solu-bulity at low-base content (acid compositions). Near the orthosilicate composition the solubility increased with basicity for silicates in which the cation displayed a weak ion-oxygen attraction and apparently decreased for those in which the cation showed a strong ion-oxygen attraction; metasilicates of the former class dissolved more water than those of the latter. Temperature had little effect on water solubility. The experimental results are interpreted on the basis of two modes of solution, the contribution of one decreasing, and that of the other increas -ing, with increased melt basicity. In the former, solution occurs through interaction with doubly-bonded oxygen atoms and in the latter, through interaction with singly-bonded oxygen atoms, or, in very basic melts, through reaction with free oxygen ions. THE hydrogen content of a steel melt is in a large measure determined by water dissolved in the slag. In some glasses water may be a major cause of "seeds". Water vapor in the furnace atmosphere is the primary source in both instances. A knowledge of the mechanism of water solution in silicate melts should help in assessment of practical methods for its control in steelmaking and glass refining. Walsh et a1.l measured the water content, expressed as hydrogen, of 40 pct lime-20 pct alumina-40 pct silica and 62 pct manganese oxide-38 pct silica melts as a function of the steam partial pressure, in equilibrium with the melt. Tomlinson 2 and, also, Russell3 investigated this relationship for a molten 30 pct soda-70 pct silica glass. In all three investigations, the solubility of water was found to be proportional to the square root of the partial pressure of steam. Moulson and Roberts 4 confirmed this relationship for a silica glass. On the basis of the square root relationship, Tomlinson2 and Russell3 interpreted the solution reaction as "network-breaking", similar to that expected on the addition of metal oxides to silica. Walsh et al.&apos; postulated two possible modes of solution, one the mechanism suggested by Tomlinson and Russell and the other the reaction of the water molecule with an oxygen ion to form hydroxyl ions. These two modes of solution suggest opposite effects of melt basicity on water solubility. However, little appears to be known about the effect of melt basicity on water solubility. Walsh et a1.l found, in the lime-silica system, that the water content increased slightly with increased basicity. As these authors pointed out, this does not appear to be in accord with their further observation that slags containing little or no silica dissolve very little water. Kurkjian and Russell5 measured the effect of basicity on water solubility in alkali silicates in the composition range 15 to 45 mole pct alkali oxide. They found a minimum in the water content at about 25 mole pct alkali. This was interpreted on the basis of two concurrent solution reacZions; one in which solubility was proportional to the activity of doubly-bonded oxygen and, in the other, proportional to the activity of singly-bonded oxygen. The present work was aimed at establishing the effect of basicity on water solubility in silicate melts over as wide a range of compositions as practical. APPARATUS AND EXPERIMENTAL PROCEDURE The silicate melt was equilibrated with a "carrier-gas" of accurately known water content, quenched, and analyzed for water by a vacuum fusion technique. Some pertinent details of the equilibration procedure, analysis technique, preparation, and handling of the silicates are given below. Gas-Silicate Equilibration. The apparatus used to equilibrate the melt with the gas mixture was similar to that used by Walsh et al.&apos; but with some important modifications.6 Purification trains were provided for nitrogen and hydrogen; whenever air or oxygen was used as carrier gas the nitrogen purifiCation train was used with the copper furnace at room temperature. Gas flow rates were measured with capillary flow meters; bleeders filled with a mixture of dibromo and tribromo ethyl benzene (density about 2 g per cc) were used for convenience in controlling flow rates.

Jan 1, 1963

By L. J. Howell, H. H. Kellogg

AN a previous paper&apos; the phase diagram and vapor pressure of melts in the systems NaC1-ZrCl,, KC1-ZrCl,, and NaC1-KC1 (1:1 molar)-ZrC1, were reported. This note supplements the earlier paper with the results of electrical conductivity measurements on NaC1-ZrC1,and NaC1-KC1 (1:l molar)-ZrC1, melts. The design of the conductivity cell is shown in Fig. 1. Tungsten electrodes, A, were sealed into the Pyrex cell, C. That portion of the electrodes in contact with the melt was covered with a tight-fitting platinum cap. The electrodes were sur-

Jan 1, 1960