Search Documents

By J. R. Elenbaas, J. A. Vary, D. L. Katz

The development of gas fields, oil fields and aquifers for storing natural gas is treated from two main vieu.-points: (I) the volumetric storage capacity for gas in a given situation and (2) the prediction of the number of wells required for the delivery of gas. Other experiences in the design and operation of storagc fields are incluclerl INTRODUC TION Storage of natural gas in underground reservoirs near the terminus of long distance pipelines has been the prime factor in opening the space heating market to the natural gas industry. Storagc has permitted a major. increase in both the load and the load factor of pipe-lines; some are now operating at steady load throughout the year. Thus, underground storage has been responsible for the rapid increase in demand for natural gas in recent years. Three types of reservoirs have been used for gas storage: natural gas reservoirs, oil reservoirs, and waterbearing sands or aquifers. This paper presents the factors to be considered when developing gas storage reservoirs of these three categories. There are two prime considerations tor any storage reservoir: (1) the volume of gas which a given reservoir will store advantageously and (2) the number 01 wells needed to provide the required peak deliverability. These two problems will be considered for the three types of reservoirs just noted STORAGE IN PARTIALLY DEPLETED GAS FIELDS Early storage operations consisted of replenishing the natural gas in a depleted gas field situated adjacent to the market. Today, newly discovered fields near the market may be considered for storage, and this discussion applies equally to both types of reservoirs. For reservoirs originally containing gas or oil, the question of the impermeability of the cap rock nor-mally does not arise. However, such fields are likely to have many wells drilled either to or through the reservoir under consideration. Positive assurance must be obtained that such wells are or can be made mechanically tight. Corroded casings may need to be lined or permanently plugged. Abandoned wells should bc reopened and properly cemented. The volumetric capacity for gas storage depends upon space available in the porous rock as well as pressure and temperature of the gas in the reservoir. The production-pressure decline data on partially depleted gas reservoirs without water drive permit calculation of the reservoir space for gas. Isopachous maps of sand volume and porosity data for the reservoir rock provide an alternate method of calculating the pore volume for water-drive reservoirs. The pressure range selected for the storage cycle depends upon ()) the safe upper limit of pressure. 2) the flow capacity of wells and (3) compression requirements when injecting gas into the reservoir or delivering to market. Normally, gas and oil fields have pressures at discovery in the range of 0.43 to 0.52 psi/ft of depth. Pressures of around 1.0 to 1.2 psi/ft of depth appear to lift the overburden1-3 and invite uncontrolled movement of fluids in the porous rock. Some top pressure is normally selected for a storage reservoir ranging from below discovery pressure for deeper reservoirs to 0.65 psi/ft of depth for shallower reservoirs. Pressures to 0.66 psi/ft have been experienced without difficulty. The lower pressure limit is set by water intrusion accompanying low pressures, reduced flow capacity for wells at lower pressures and compression requirements. Depletion-type gas reservoirs often encounter water problems in the later stages of gas production. Such water intrusion may be due to movement from the surrounding aquifer. Accordingly, displacement of this water back into the aquifer by gas pressure and subsequent surges of water corresponding to the gas storage pressure cycle must be considered. Storage fields often produce in four months a volume of gas equal to its initial content. Rapid decreases in reservoir pressure occur, such as 20 psi/day. Accordingly, closed-in pressure observation wells which reflect the pressure in the bulk of the reservoir are required for following the operation of the reservoir. It has been found that a plot of observation wellhead pressures against gas content, Fig. 1, is very useful in observing operation of the field, checking the inventory and predicting future behavior. The plot is based on a given quantity of base or cushion gas in place. The injection and withdrawal curves may spread depending upon the homogeneity of the reservoir rock. permeability of the rock, well spacing and flow rates.

By W. E. Brigham, P. W. Reed, J. N. Dew

By C. Ernest Birchenall, Robert F. Mehl

Application of diffusion laws in the customary form to experimental studies in binary metallic solid solutions has shown the diffusion cocfficient to vary with concentration for all systems investigated. The factors determining this variation have not been ascertained. However, the question of whether the diffusion coefficient would become a constant, independent of concentration throughout a single phase if the concentration gradient in the diffusion equation were replaced by an activity gradient has been an attractive subject for speculation. Wagner¹ derived an expression for the force acting on a diffusing particle in terms of the chemical potential. This was also the approach chosen by Jost2 in his monograph. From a somewhat different point of view, Eyring3 and his co-workers have used activity gradients when dealing with diffusion in concentrated nonideal solutions. The only actual test with experimental data is that given by Darken,4 though this is more qualitative than quantitative. Many others opposed the application in any way of thermodynamic concepts to kinetic phenomena, including diffusion processes. A rigorous examination of this principle requires good data expressing the relationship between activity and concentration for solid solutions for which reliable diffusion work has been done. The literature provides such information only for the interstitial solution of carbon in gamma iron (austenite) and for the substitutional copper-zinc solutions (alpha brass). Activity data for carbon in austenite at 800°C and 1000°C are available from the recent work of Smith5 on the equilibrium of hydrogen-methane and carbon monoxide-carbon dioxide mixtures with gamma iron. Combining these with the diffusion studies of Wells and Mehl6 makes possible a quantitative test for this interstitial solid solution. The vapor-pressure determinations for zinc over brass by Hargreaves7 allowed the calculation of activities in this system over a wide range of temperatures and concentrations. Extensive investigation of diffusion in this substitutional solid solution has been carried out by Rhines and Mehl.8 Activities in Brass9 If the vapor phase of zinc is assumed to behave as an ideal gas, any solid or liquid solutions that are in equilibrium with the same partial pressure of zinc at the same temperature have the same thermodynamic activity of zinc. In order to assign a numerical value to the activity azn, it is necessary to choose some standard reference state to which an activity value of unity is arbitrarily assigned. It is customary to choose the liquid or solid state of the pure material. Then azn is defined numerically by

Jan 1, 1947

By C. Ernest Birchenall, Robert F. Mehl

Application of diffusion laws in the customary form to experimental studies in binary metallic solid solutions has shown the diffusion cocfficient to vary with concentration for all systems investigated. The factors determining this variation have not been ascertained. However, the question of whether the diffusion coefficient would become a constant, independent of concentration throughout a single phase if the concentration gradient in the diffusion equation were replaced by an activity gradient has been an attractive subject for speculation. Wagner¹ derived an expression for the force acting on a diffusing particle in terms of the chemical potential. This was also the approach chosen by Jost2 in his monograph. From a somewhat different point of view, Eyring3 and his co-workers have used activity gradients when dealing with diffusion in concentrated nonideal solutions. The only actual test with experimental data is that given by Darken,4 though this is more qualitative than quantitative. Many others opposed the application in any way of thermodynamic concepts to kinetic phenomena, including diffusion processes. A rigorous examination of this principle requires good data expressing the relationship between activity and concentration for solid solutions for which reliable diffusion work has been done. The literature provides such information only for the interstitial solution of carbon in gamma iron (austenite) and for the substitutional copper-zinc solutions (alpha brass). Activity data for carbon in austenite at 800°C and 1000°C are available from the recent work of Smith5 on the equilibrium of hydrogen-methane and carbon monoxide-carbon dioxide mixtures with gamma iron. Combining these with the diffusion studies of Wells and Mehl6 makes possible a quantitative test for this interstitial solid solution. The vapor-pressure determinations for zinc over brass by Hargreaves7 allowed the calculation of activities in this system over a wide range of temperatures and concentrations. Extensive investigation of diffusion in this substitutional solid solution has been carried out by Rhines and Mehl.8 Activities in Brass9 If the vapor phase of zinc is assumed to behave as an ideal gas, any solid or liquid solutions that are in equilibrium with the same partial pressure of zinc at the same temperature have the same thermodynamic activity of zinc. In order to assign a numerical value to the activity azn, it is necessary to choose some standard reference state to which an activity value of unity is arbitrarily assigned. It is customary to choose the liquid or solid state of the pure material. Then azn is defined numerically by

Jan 1, 1947

By J. H. Bechtold, R. Kossowsky

1 HE superplastic behavior of the eutectoid A1-78 wt pct Zn alloy has been thoroughly investigated by Back-ofen et al.' The superplastic elongations and the marked resistance to necking were rationalized in terms of high strain rate sensitivity. In a subsequent paper2 superplastic behavior was formulated to show Nabarro-Herring diffusional creep as rate controlling at low strain rates, giving way to a dislocation climb process at higher strain rates. In a paper devoted to an interpretation of superplasticity in two-phase alloys, Packer and sherby3 have included the results of an examination of the structure of an Al-Zn eutectoid specimen before and after superplastic deformation. No significant change in grain size or directionality was observed in the deformed microstructures. This one observation led the authors3 to suggest that con- tinuous recrystallization or grain boundary migration was responsible for superplasticity. The purpose of this note is to report our observations on the superplastic behavior of the Al-Zn eutectoid alloy which differ in certain respects from works previously reported. Following Hayden et al., the results are discussed in terms of dislocation climb as the important factor during superplastic deformation. A heat of nominally high (99.995) purity 22 wt pct A1-78 wt pct Zn was induction-melted and cast into a 0.5 by 6 by 12 in. slab. The slab was heated to 350°C and rolled to 1/8-in.-thick plate. The plate was then cold-rolled to 0.040-in. thickness, annealed at 35OaC, and rolled to the final thickness of 0.020 in.* Speci-

Jan 1, 1969

By C. E. Wood, E. P. Barrett, T. L. Joseph

The invention of the Bessemer converter process in 1856 added great impetus to the manufacture of steel and is one of the outstanding contributions to process metallurgy. Although the process of refining pig iron by passing air through the molten metal bears the name of Henry Bessemer, it should be mentioned in passing that William Kelley of Eddysville, Ky., worked on the process as early as 1847. Kelley was granted a patent on the process in 1857, inasmuch as he was able to prove priority in discovery.' After considerable litigation in 1865 the respective interests of Kelley and Bessemer were combined. On Sept. 10, 1856, Robert Mushet of England obtained his first patent on the application of manganese to cast steel. Mushet anticipated trouble in purifying iron by passing currents of air through it: His patent specified that steel made in this way often contained flaws and was red short or cold short. Mushet understood the refining of pig iron into steel well enough to realize the difficulties likely to be cncountered from oxidation of the iron. Mushet was not only an inventor; he was also an investigator. He understood the principle of selective oxidation which takes place in the converter process, and he realized therefore that the remedy for over-oxidation was attainable if a suitable metal could be found at a reasonable cost and in sufficient quantities. His first experiments were made in small crucibles holding a few ounces of metal. Later his work was conducted on a larger scale and with complete success. Manganese had been used in making steel a quarter of a century before the converter

Jan 1, 1927

By J. A. Knox, R. M. Lasater, J. M. Tinsley

Chemical squeeze treatments have been used to provide temporary relief from certain production problems. The chemical fracture-squeeze technique, combining the effects of a fracturing treatment and a squeeze operation, has been more successful than conventional squeeze operations. Knowledge derived from well stimulation and reservoir engineering research provides a means for predicting the theoretical effective life of such a treatment. Analysis of theoretical equations and concepts developed allows selection of improved treatment techniques based on specific formation conditioins. Theory used in this analysis was developed as an extension of previous electrical model studies made to establish the expected flow and pressure profiles adjacent to a fracture system. The chemical fracture squeeze technique can be utilized in the economic application of corrosion inhibitors, emulsion breakers and paraffin and scale inhibitors. Application of this technique is shown to be effective. The slow return rate of injected chemicals, controlled by the resultant flow profiles and treatment variables, permits extended periods of chemical effectiveness. Results of field treatments are given, showing that the concepts outlined above for chemical fracture-squeeze treatments are valid and that applying this technique can help alleviate many current production problems. INTRODUCTION Much progress has been made in the last 10 to 15 years in developing chemicals for use in stimulating wells, maintaining production and protecting well equipment from damage due to corrosion. Not too many years ago, some wells seemed to dry up or wear out. In many cases the wells were produced as long as possible without any attempt at maintaining productivity. Even with the advent of new and better stimulation techniques, a rapid decline in production was observed. Methods of removing and, in some instances, preventing damage have been developed. Among thosc factors responsible for uneconomical production are scale, paraffin, corrosion, bacteria, water blocks and emulsions. Soluble scale-prevention chemicals have been developed1,2 that can be placed in a formation along with frac- turing sand. As the water produces back across this bed, the solid material dissolves slowly and can provide long-term protection from scale. However, bottom-hole temperature and salinity of produced water vary widely and both these factors influence the rate of solubility. Scale inhibitor composition is also a controlling factor. Some of the solid material may be crushed, increasing the surface area exposed to water and increasing the rate at which it dissolves. Some of the material may never be contacted by water and can be lost. However, this type of treatment has been very successful in many instances and has helped maintain economical production for extended periods of time. Liquid scale inhibitors, which are more widely applicable and more stable, have been developed in recent years; however, because they are liquids, their use has been restricted to treatment down the annulus, using metering pumps to provide proper concentrations in the produced fluid. This has prevented use in wells containing packers, in dually completed wells and in gas-lift and flowing wells. Wells that operate with an open annulus may also experience severe corrosion problems due to introduction of oxygen. Paraffin inhibitors3 have been developed that can be fractured into a well as particulate solids to be slowly dissolved in the produced fluid. These materials are not usually effective in wells with a bottom-hole temperature in excess of 120F since solubility rate may be too fast if that temperature is exceeded or if aromatic content of the oils is unusually high. Corrosion inhibitors have been developed that can be fractured' into a well for long-term feedback, but development of a material with proper solubility or feed rate has been difficult. Corrosion inhibitors are available in many different forms. Liquids have been lubricated down the annulus or sticks or pellets dropped down tubing. Inhibitor squeeze treatments5 devcloped a few years ago led to development of inhibitors with particularly strong film-forming properties.6,7 This technique basically involves displacing a highly concentrated solution of the inhibitor into the formation through the tubing. Kerver and Hanson8 studied the adsorption properties of inhibitors on various types of formations. They showed that, even though the inhibitor was displaced radially into the true permeability, it could be produced back for a long period of time because of slow desorption from the rock. Methods developed for monitoring the return of these inhibitors generally have established 1 to 6 months as the effective limit before retreatment is necessary.9 Inhibitors displaced into the interstices of the formation sometimes cause emulsions that either hamper production or cause treating problems on the surface.

By K. Huessener

This paper attempts a survey of the principles involved in the combustion of blast-furnace gas in boilers and stoves. I do not expect to be able to give much information which is actually new, since the laws and methods of calculation pertaining to this problem are contained in a number of handbooks; but, so far as I am aware, they have nowhere been treated exclusively with reference to this one problem of gas economy. The road which I follow is less that of strictly scientific research than that of the practical engineer, faced by operation problems which require a quick solution by easily accessible means without a prolonged search in scientific handbooks. For this purpose I give a number of tables and diagrams, as well as the results of many years1 practical working experience as combustion engineer, which I trust will prove useful to my readers. HlSTORICAL Considering the tremendous efforts made during the last 15 years to increase the efficiency of all kinds of power plants, it is highly surprising that until a comparatively very recent period, progress in the economical combustion of blast-furnace gas has been so slow, The explanation generally put forth, that fuel has been so cheap that it was hardly worth while to bother about this economy, will not hold good, for the greatest trouble was taken to improve the combustion of coal and to reduce the consumption of steam, The most plausible explanation appears to be the general impression, held as an accepted fact, that gas, especially hot, uncleaned, blast-furnace gas, was not a good boiler fuel. Many managers of high repute had tried unsuccessfully to improve the conditions of its use, and the dictum went forth that efficiencies of over 60 per cent., particularly with high loads, were impossible. This was the situation not only in the United States, with very cheap fuel, but also in Europe, where fuel prices are twice and three times as high.

Jan 1, 1916

By W. O. Philbrook, C. W. McCoy

The reduction of chromous oxide from lime silica alumina slags by carbon-saturated iron behaves as a first-order process having a rate of 0.001 grams Cr min 1 cm 2 (pct Cr ) , substantially independent of slag composition and temperature over an important range for iron smelting. The equilibrium ratio (pct Cr)/[pct Crl is below 0.04 for slags having lime-silica ratios above 0.6. MANY studies have been conducted on chromium in slag-metal systems under oxidized conditions. The Purpose of these investigations has been twofold; namely, (1) to determine those conditions which lead to greater chromium recovery in electric-furnace and open-hearth practice, and (2) to determine the nature of oxide inclusions and de-

Jan 1, 1959

By A. D. Schwope, L. R. Jackson, K. F. Smith

Burghoff and Blank1 have pointed out that the creep properties of hard-drawn coppers are closely associated with their individual softening characteristics and have further shown that the creep resistance of various types of copper is improved, under certain circumstances, by cold stretching. In the design of certain types of electrical machinery, it is important to have the creep resistance as high as possible; furthermore, short-time creep strength is important since in many cases stresses are large only during warming-up and cooling-down periods. In this paper, data are presented showing the effect of cold work on the short time creep strengths of various types of commercial copper under several conditions. It is shown that trends from short-time creep tests are evident at longer times. Materials Used in the Investigation The coppers used in this investigation were commercial grade and of two basic types, oxygen free high conductivity (OFHC) and tough pitch. Additions of silver in amounts of 15 and 25 oz per ton were added to each of the two coppers. The analyses of these six coppers are given in Table 1. Originally, they started as wire bars 4 X 4 X 54 in. A. square rod was made by hot rolling the wire bars to 9/16-in. rod in 8 passes. This rod was then cold drawn to 0.445-in.-diam rod and annealed for 3 1/2 hr at 1000°F. It was then cold drawn to 0.325-in. rod and again annealed at 1000°F for 3 1/2 hr. Hard square rods were then made by cold rolling to 0.257 X 0.257-in. rod. Soft wire was made from the hard- drawn material by annealing at 650°F for 3 hr. The final rolling was performed using a set of 9-in. grooved rolls revolving at 30 rpm, which produced square wires. Reductions of approximately 5, 20, 30, and 40 pct were obtained using several passes in the same direction for the large reductions. The 5 pct reduction by drawing was accomplished using a steel die having 2 parallel bearing surfaces. The die angle was 7 1/2 degrees and the wires were lubricated with a paste of ceresin wax dissolved in carbon tetrachloride. The speed of drawing was 13 fpm. Since work was done on only two sides of the wire simultaneously, it was necessary to rotate it 90 degrees each pass to insure uniform deformation. The room-temperature tensile properties of the various tempers are given in Table 2. The grain size of the an- nealed 0.257-in. wires was uniform and averaged about 0.035-0.045 mm. Experimental Procedures for Short-time Creep Tests Standard creep-test frames (Fig 1) were used for the testing. Special fixtures were designed to apply axial compressive and tensile loads to the copper wires. The compression specimens were 1 in. long and the ends were ground flat and parallel. The creep in compression was indicated by the movement of reference marks s-ratched on intersliding platinum strips attached to the moving heads of the fixture. The movement was measured with an optical micrometer fitted with a filar eyepiece on which the smallest division was 0.00005 in. The tensile creep specirriens were 4 in. long which provided ample gripping surface for the jaw-type grips. The platinum strips were attached to a one-inch gauge length of the wire and the creep measured as previously described. The single-specimen furnaces were connected to individual power and control sources. The controlling equipment consisted of Foxboro controllers

Jan 1, 1950

By Sage B. H., Lacey W. N., G. W. Billman

The composition of the coexisting phases in the methane-ethane-n-pentane system was determined at 100°F. This was accomplished by withdrawing samples of the coexisting phases under isobaric-isothermal conditions. The relative amount of each of the components present in the liquid and gas phases was determined by conventional analytical fractionation methods. The phase behavior of this system approximates that estimated from generalized correlations which take into account the influence of the nature and amount of each of the components present upon the equilibrium. It was found that for particular pressures and temperatures the equilibrium constant of each of the components was influenced significantly by the composition of the system and this effect was more pronounced at the lower pressures for methane than for the components of greater molecular weight. However, at the higher pressures approaching the maximum two-phase pressure for the system at this temperature the composition markedly influences the equilibrium constants of all the components at a particular pressure and temperature. The results of this study are presented in graphical and tabular form. Introduction The phase behavior of many of the binary systems containing parafin hydrocarbon components from methane through n-pentane has been investigated during recent years. In addition the compositions of the coexisting phases in mixtures of crude oil and natural gas have been studied.' However, these results do not establish the influence of the nature and amount of the other substances making up a multi-component system upon the gas-liquid equilibrium constant of any one component. A preliminary correlation on the basis of values for binary systems was made2 utilizing such experimental information as was available. However, there is need for much additional information regarding behavior in systems containing more than two components. Study of the phase behavior of ternary systems offers a feasible attack upon the determination of the influence of composition as well as of pressure and temperature upon the several equilibrium constants concerned. An investigation of the phase behavior of the methane-propane-n-pentane system at 100°, 160°, and 220°F was reported.".' This work served to illustrate the marked influence of concentration of the other components upon the equilibrium constants. Variations of as much as 50 pct in the equilibrium constants for methane for fixed temperature and pressure were observed in regions remote from the critical state. Likewise there was a marked variation in the equilibrium constants of propane and n-pentane as a result of changes in the composition. These results indicated the desirability of investigating additional ternary systems. The present paper deals with a study of the methane-ethane-n- pen-tane system at 100°F, which is similar in many respects to the work upon the meth-ane-propane-n-pentane system cited above.

Jan 1, 1948

By Sage B. H., G. W. Billman, Lacey W. N.

The composition of the coexisting phases in the methane-ethane-n-pentane system was determined at 100°F. This was accomplished by withdrawing samples of the coexisting phases under isobaric-isothermal conditions. The relative amount of each of the components present in the liquid and gas phases was determined by conventional analytical fractionation methods. The phase behavior of this system approximates that estimated from generalized correlations which take into account the influence of the nature and amount of each of the components present upon the equilibrium. It was found that for particular pressures and temperatures the equilibrium constant of each of the components was influenced significantly by the composition of the system and this effect was more pronounced at the lower pressures for methane than for the components of greater molecular weight. However, at the higher pressures approaching the maximum two-phase pressure for the system at this temperature the composition markedly influences the equilibrium constants of all the components at a particular pressure and temperature. The results of this study are presented in graphical and tabular form. Introduction The phase behavior of many of the binary systems containing parafin hydrocarbon components from methane through n-pentane has been investigated during recent years. In addition the compositions of the coexisting phases in mixtures of crude oil and natural gas have been studied.' However, these results do not establish the influence of the nature and amount of the other substances making up a multi-component system upon the gas-liquid equilibrium constant of any one component. A preliminary correlation on the basis of values for binary systems was made2 utilizing such experimental information as was available. However, there is need for much additional information regarding behavior in systems containing more than two components. Study of the phase behavior of ternary systems offers a feasible attack upon the determination of the influence of composition as well as of pressure and temperature upon the several equilibrium constants concerned. An investigation of the phase behavior of the methane-propane-n-pentane system at 100°, 160°, and 220°F was reported.".' This work served to illustrate the marked influence of concentration of the other components upon the equilibrium constants. Variations of as much as 50 pct in the equilibrium constants for methane for fixed temperature and pressure were observed in regions remote from the critical state. Likewise there was a marked variation in the equilibrium constants of propane and n-pentane as a result of changes in the composition. These results indicated the desirability of investigating additional ternary systems. The present paper deals with a study of the methane-ethane-n- pen-tane system at 100°F, which is similar in many respects to the work upon the meth-ane-propane-n-pentane system cited above.

Jan 1, 1948

By B. Das, V. Hucka

Two different types of filtration methods for in-situ gasification of coal are described. The different factors, i.e., geological, technological, and others, which affect in-situ gasification are given. The layout and operation of filtration methods of in-situ gasification are described in detail. The results of a case history are described.

Jan 1, 1977

By W. N. Hiatt

The mathematical theory of the flow of two-phase, incompressible fluid through porous media is clarified, and the development of a general fluid displacement equation for two-phase, incompressible vertical flow through porous media is outlined. The relationship between the three components of the equation — the "fluid drive effect", the "gravity effect", and the "capillary effect'' — is discussed, as well as implications of the analysis in connection with the study of certain types of petroleum reservoirs. INTRODUCTION The purpose of this paper is to clarify and summarize the mathematical basis of the theory of two-phase incompressible fluid flow through porous media, particularly as it pertains to vertical flow, and to present a qualitative* exposition of the controlling factors involved in circumstances where this type of flow may exist. Although the generally accepted theory of heterogeneous fluid flow through porous media was developed a number of years ago by Muskat,1 and Buckley and Leverett2, 3 using the basic premise of Darcy, (and since then expounded upon by many others) there is a need for an over-all summary and clarification of this theory, especially regarding certain types of applications in connection with so-called "gravity-drainage-type reservoirs". The source and derivation is outlined for what is referred to here as the "General Fluid Displacement Equation for Incompressible Vertical Two-Phase Flow through Porous Media''. This equation would apply under the condition where the pressure drop along the path of flow is negligible in comparison with the pressure level on the system, or where compressibility and solubility effects are negligible. These conditions exist ordinarily in gravity-drainage-type reservoirs. Specifically, it will be shown that this general equation may be developed directly from the basic equations, which, according to present theory, govern the general case of viscous heterogeneous flow through porous media. This general equation has appeared in the literature previously, but in most cases its development from basic theory is not indicated clearly, or the equation is presented in terms of groups of constants and variables involving reduced or dimensionless quantities. This presentation is expedient in cases of experimental or computer applications; but it may make it difficult for the practicing petroleum engineer to identify all the factors involved or to understand the relationships between them. Therefore, in the following development, only ordinary mathematical parlance will be used, and no terms involving groups of other equations or reduced or dimensionless quantities will be used. DERIVATION The following equations for two-phase oil and gas flow result from analogy with Muskat's general equations,** if solubility and compressibility effects are neglected, and if all volumes are considered in terms of reservoir conditions, and the water phase, if present, is considered to be immobile (or effectively a part of the porous medium.) In this case, the sum of the oil and gas saturations may be taken as unity, and the saturation of each phase is in terms of the total hydrocarbon saturation. Note that in Eqs. 1 and 2, and in the derivation following, z is taken as positive in the vertically downward direction,

Jan 1, 1969

By L. W. Strock

Metallurgists handling lead and zinc ores have long been familiar with the spectrograph as a routine analytical tool, as its earliest regular use by American industry was in controlling impurities of zinc metal and its alloys. This application has been extended to other metal industries on an extensive scale, accompanied by refinements of procedure to such an extent that a large part of some metals produced, especially magnesium, aluminum and steel, are checked only by spectrographic methods for conformity to specifications. The spectrographic analysis of ores and other poorly conducting powdered solids presents difficulties not encountered with metallic samples, which can be arced or sparked as self-electrodes or can be readily dissolved, so that their solutions can be analyzed, as in the American Society for Testing Materials standard methods for zinc and zinc-base alloys. Spectra of powdered solid samples can be prepared by using carbon electrodes provided with a crater of suitable size, into which the sample is packed. Ore samples and many other powdered solid materials usually analyzed in the chemical and metallurgical laboratory are more complex and varied in composition than samples of metals produced in large tonnages. 'lore preliminary work therefore is usually necessary in devising a spectrographic method for analyzing a given type of powdered sample than for analyzing metal samples, in order to use that method with confidence. The howledge that the standard samples and unknowns produce equivalent line intensities at equal concentration is the fundamental basis of any quantitative spectrographic method. On the other hand, powdered samples have an advantage over metals in that any desired number of chemical compounds can be mixed dry in any desired ratio to produce a synthetic standard. Expcrience has shown, however, that spectra of elements in finely divided compounds introduced into a standard in preparing a synthetic ore sample do not always behave in the electric arc in a manner that produces spectral line intensities similar to those observed at the same concentration in a natural mineral. In ore samples minor elements frequently are contained in the crystal lattice of larger particles of an abundant ore mineral. Their dissociation and volatilization from the sample into the arc then proceeds differently in the standard and sample, with resultant differences in intensity. During the past 10 years I have devised and applied several quantitative spectrographic methods for determining various elements in rocks and minerals in connection with studies on their geochemistry,' but the incentive has gradually changed since the summer 0. 1940 to the specific practical problem of searching for domestic sources of rare and stratcgic metals. The

Jan 1, 1949

By Walter Kauenhowen

Germany's crude-oil production during 1937 totaled 3,174,157 bbl., an increase of 1.9 per cent over the 3,112,494 bbl. produced in 1936. According to official published data, and using a conversion factor of 1 metric ton = 7 bbl., the oil production of Germany in 1937 by fields was as follows:

Jan 1, 1938

By Keith Leonard Sutherland

THIS paper is a study of the differential flotation of the sulphide minerals in the presence of salts of silver, lead and zinc. In practice, accidental activation due to these salts is more important than their use as reagents to replace copper sulphate. The general method of investigation has been based upon contact tests, the temperature of 35°C. being chosen in conformity with earlier work. Potassium ethyl xanthate and potassium amyl xanthate were selected as collectors and pure sulphide minerals were used. The experimental procedure has been outlined in earlier papers and all solutions were kept carbonate -free.1,4 Contact, or spreading of an air bubble, at a mineral surface indicates the presence of an adsorbed collector film. PURITY OF REAGENTS The xanthates were purified in the usual manner.1 Neither the cyanide nor the sodium hydroxide solutions contained sufficient carbonate to give a precipitate with barium chloride solution. The silver sulphate was prepared from pure silver nitrate by evaporation with concentrated sulphuric acid until there was no evidence of brown fumes. This solution was diluted and the difficultly soluble sulphate washed with water so that unchanged nitrate was dissolved. The resultant crystalline powder was pure white. The lead and zinc salts were prepared by dissolving especially pure lead and zinc in C.P. nitric and sulphuric acid solution and the crystals drained. The standard solutions were checked by titration. It was felt desirable to use the sulphate radical wherever possible, but since lead sulphate was insufficiently soluble for the purpose of the experiments, it was necessary to use some other lead salt. A.R. copper sulphate was used without further purification. RESULTS The results are presented in the accompanying figures; the areas of noncontact (nonflotation) are shaded in Figs. 8, 9, 10 and 11; in the remainder they lie to the right of the curve. Zinc Sulphate The curves in Fig. I are to be compared with those for Fig. 2, for which zinc sulphate is absent. This comparison shows that the influence of the zinc ion is usually small. Its influence is more marked, however, for chalcopyrite in the absence of cyanide. The influence of zinc sulphate is also marked for copper-activated sphalerite, for which tests were made only in the absence of cyanide. The results are of importance in the separation of pyrite from copper-activated sphalerite when, zinc sulphate is added in the lead flotation section (p. 204 of ref. I). Sphalerite does not adsorb the collector (i.e., become floatable) under the conditions chosen.

Jan 1, 1942

By William H. Morris

At the Glen Summit meeting, the question of controlling the silicon in pig-iron WAS raised; and as this has been deemed by most furnace-men for years past a matter of special difficulty, an account of our experience in the matter may be of interest. When running on mill-iron, some years ago, we aimed to keep

Jan 1, 1893

By R. A. Morse, C. R. Stewart, F. F. Craig

This paper preFents the results of a series of model flow test on a number of large limestone cores, having different pore configurations. For limestone cores having substantially sandstone type porosity, the production characteristics for solution and external gas drives are similar. For cores whose pore spaces were microscopically heterogeneous (i.e., consisted of combinations of solution cavities, matrix. and fissures), the production characteristics lor solution and external gas drives vary widely. The degree of divergence between gas-oil relative permeability relationships calculated from solution or external gas drive tests is an indication of heterogeneity of rock pore structure. The results of water floods on cores depleted by solution gas drive for each of these two general types of limestone porosity are also shown. Generalizations are made on the water flood recovery that could be expected from each of these two types of limestone porosity. The similarity between solution drive field performance and model solution drive performance on cores from the same formation is shown for several cases. This indicate? the feasibility of predetermining limestone field performance from such large core tests. Photomicrographs of plastic-impregnated rock thin sections of the samples tested are presented as an aid in understanding the flow test performances. INTRODUCTION During the past 15 years. reservoir engineers and research workers have developed methods of testing rock and fluid samples and applying the results, through calculation, to allow reasonably satisfactory predictions of oil recoveries and performances to be expected in sandstone oil recervoirs. It has been determined that representative fluid flow data can be obtained on rock samples as small as three-fourths in. in diameter by one in. long in most sandstones. However, little has been accomplished toward the laboratory determination of fluid flow characteristics in limestones. There has been a great deal of speculation as to the influence of variations in pore size, shape, and degree of interconnection upon oil recovery processes, and a great deal of thought has been given to the interpretation of limestone field perfomance. It has been generally recognized that predictions of reservoir performance based on oil displacement tests on small limestone core samples the size of those used for sandstone tests can often be misleading because of the improbability of obtaining a representative sample in such a small core. Obviously, if there are present in the rock, pore openings of the magnitude of 1/16 in., or fractures or solution channels up to one in. or more in length, it will be impossible to cut any sample less than one in. in any dimension which would represent the flow geometry of the gross rock system. In some formations, the individual openings in the rock are of such size that it would be impossible to obtain a good sample of the flow system even in the total core available from conventional-sized well cores. However, by increasing to the maximum the size of the sample used, it should be possible to obtain representative flow data from the majority of limestone reservoir materials which can be used for prediction of future primary production performance or response to be expected from secondary recovery measures. The only alternatives to obtaining good laboratory test data to serve these purposes are extrapolation of primary performance data obtained by partial depletion of a field, or obtaining information from pilot tests. It has been shown previously, and will be demonstrated further by the work reported in this paper, that extrapolation of solution gas drive performance for an estimate of gas injection response can be very misleading in reservoirs of heterogeneous type porosity. Although it cannot be expected that laboratory information can ever eliminate the necessity of small-scale pilot operations, it is expected, as is now the situation with sandstone reservoirs, that laboratory tests should provide reliable information for screening of

Jan 1, 1953

By H. I. Aaronson, C. Laird

Cold rolling by 50 pct a A1-4 pct Cu alloy containing many 0' plates has been found to accelerate markedly the transformation of 8' to 0 upon further aging. Although the basic mechanism of this transformation remains unchanged by plastic deformation, the nuclea-tion kinetics of 8 become appreciably more rapid and also less dependent upon temperature. Particularly at lower aging temperatures, rounded idiomorphs replace several faceted rnorphologfes. The rates of growth of 9 idiomorphs in deformed specimens aged at 300°C are appreciably more rapid than simple volume diffusion control allows. This observation is shown to be explained by an excess vacancy, rather than by a dislocation Piping mechanism of growth. ThE rather complex phenomenology of the 8' —8 transformation in Al-Cu alloys has been recently elucidated in considerable detail by means of transmission electron microscopy.'-4 This technique was also employed in the present investigation in order to examine the effects of plastic deformation upon the transformation of 8' to 8. The mechanism of the transformation in undeformed Al-Cu alloys has been established as the following sequence of events.1"4 The first step is the nucleation of 9 at (Y:8' boundaries. Nucleation of a 0 crystal takes place, however, at only a very small proportion of the 8' plates present. Each 0 crystal simultaneously consumes the host 8' plate and the a! in the immediate vicinity, with growth into a being the rate-controlling process. The remaining 8' plates are then dissolved as they fall under the concentration shadow of the growing 8 crystals. The evidence on the effects of plastic deformation upon these processes is intriguing, but much less detailed. The careful X-ray studies of Graf and Guinier have shown that the aging times required to form detectable amounts of 8' and 8 are reduced by prior cold working. Thomas and Nutting confirmed these results by replication electron microscopy. Nile-shwar,* on the other hand, reported that creep deformation decreases the rate of formation of 0. While this difference may have been caused by the use of concurrent rather than successive deformation and ag- ing, the X-ray technique which he used was able to monitor only the 0 phase. It is thus possible that the times needed to form 8' were increased moreg than the kinetics of 8' — 8 transformation were accelerated. At 90 pct deformation by cold rolling, Graf and Guinier found that the usual 0' —0 8 sequence is reversed: 0 forms first. von Heimendahl 10 confirmed this result with transmission electron microscopy. Pollard and Nutting, 11 and more recently Driver and Barrand, 9 having used the same technique, report that 9 also forms first during creep deformation. In the present study, the maximum amount of deformation was limited to 50 pct reduction by cold rolling in order to insure that 8 formed principally by the decomposition of . I) EXPERIMENTAL PROCEDURES This investigation was conducted on an Al- 3.93 pct Cu alloy, prepared as previously described. 4 Morphological and crystallographic effects of plastic deformation were studied in specimens annealed 6 hr at 548°C, quenched, and then aged for either 3 or 8 hr at 250°C to form large numbers of 0' plates. After cold rolling to a 50 pct reduction in thickness, the

Jan 1, 1969