Search Documents

By E. T. Turkdogan

The activity of sulfur was determined as a function of composition of ferrous sulfide by equilibrating with hydrogen sulfide-hydrogen gas mixtures at 670° , 800°, and 900". The present results supplement the available data over the composition range from 36.6 to 39.5 pct S. The X-ray lattice spacing measurements made are in accord with the available data and indicate that the limiting composition FeSl.008 may be taken for the iron-iron sulfide equilibrium. The growth rate of ferrous sulfide on iron was measured by reacting iron strips or blocks in hydrogen sulfide-hydrogen gas mixtures. Owing to the slow approach to equilibrium between the gas phase and the surface of the sulfide layer, The sulfidation experiments were carried out for several days. It is shown that the growth rate ullimately proceeds in accordance wilh the parabolic rate law. From the parabolic rate constants and the thermodynamic data on iron sulfide the self-difiusivity and chemical diffusivity of iron in ferrous bisulfide are evalualed. The self-diffusivity of iron thus derived zs found to increase with increasing sulfur content. THE ferrous sulfide known as "pyrrhotite" is a non-stoichiometric phase having a wide composition range from about 50 to about 58 or 60 at. pct, depending on the sulfur activity. RosenQvistl studied the thermodynamics of this phase over wide ranges of temperature and composition. Hauffe and Rahmel' and Meussner and ~irchenall~ studied the parabolic rate of sulfidation of iron in sulfur vapor. By using markers, these investigators showed that the iron cations were the predominant diffusing species in iron sulfide. This is confirmed decisively by the self-diffusivity measurements of condit4 who showed that the self-diffusivity of sulfur in ferrous sulfide is several orders of magnitude lower than the self-diffusivity of iron. Although much has been learned from these studies about the Fe-S system, further research on this subject was considered desirable for better understanding of the physical chemistry of iron sulfide. This work was confined to the study of the kinetics of sulfidation of iron in hydrogen sulfide-hydrogen gas mixtures. The results of this study are given in two consecutive parts. Part I, the present paper, is on the parabolic rate of sulfidation of iron and the diffusivity of iron in ferrous sulfide. The second paper, Part 11, is on the kinetics of the surface reaction between hydrogen sulfide and ferrous sulfide. EXPERIMENTAL Three types of experiments were carried out: i) equilibration of ferrous sulfide with gas of known E. T. TURKDOGAN, member AIME, is Manager,Chemical Metallurgy Division, Edgar C. Bain Laboratory for Fundamental Research, U. S. Steel Corp., Research Center, Monroeville, Pa. Manuscript submitted March 6. 1968. ISD sulfur potential; ii) X-ray studies of ferrous sulfide; and iii) measurements of the parabolic rate of sulfidation of iron. Equilibrium Studies. About 1 g of iron powder or foil. contained in a small recrystallized alumina crucible ind suspended from a calibrated silica spring, was reacted with a hydrogen sulfide-hydrogen mixture of known ratio until no further change in weight was observed. %hen the gas composition was changed and the new state of equilibrium was established after several hours of reaction time. The composition of the sulfide was obtained from the initial weight of the sample and the weight after equilibration. X-Ray Studies. The lattice parameters of some of the equilibrated samples were determined using the General Electric XRD-5 diffractometer with a cobalt tube (no filter) set at 40 kv apd 10 ma; the CoK, radiation was taken as 1.79020A. Observed 220 and 311 diffraction peaks of silicon served as an internal comparison standard to correct for possible misalignment of the goniometer. The lattice parameters of the sulfide phase were calculated from the corrected Bragg angles of the 110 and 102 peaks. Rate Studies. In the initial experiments attempts were made to measure the parabolic rate of sulfidation by measuring the gain in weight of a thin iron strip, -0.05 cm thick, suspended from a silica spring in the reacting atmosphere. The preliminary experiments showed that this technique was not reliable for the measurement of the parabolic growth rate of the iron sulfide layer. In the subsequent experiments the data on growth rate were obtained by measuring, on a microscope stage, change in the thickness of the sample after reaction for a specified time in a hydrogen sulfide-hydrogen mixture of known sulfur activity. For each reaction time a new sample was used. Precision-machined iron blocks, 0.5 by 2 by 5 cu cm, were de-greased and annealed in hydrogen for several hours prior to the sulfidation rate measurements. The experiments were carried out at 670°, 800°, and 900°C in gas mixtures having the ratios, and 1.0 for periods of times from a few hours up to 8 days. Apparatus and Materials. A vertical globar tube furnace with a 3-in.-long uniform temperature zone was used. The glass tube fittings were fused on the zircon reaction tube, 1.5 in. diam. The temperature was measured with a Pt-10 pct Rh/Pt thermocouple placed in the hot zone of the furnace inside the reaction tube (an alumina thermocouple sheath was used). A separate thermocouple was used for the temperature controller which maintained the furnace temperature constant within about 2°C. Anhydrous liquid hydrogen sulfide and oxygen-free dry hydrogen from gas tanks were used in preparing the gas mixtures by the constant head capillary flow-meters. In all cases volume flow rate was 1000 cu cm per min at stp, corresponding to a linear velocity of about 6 cm per sec at 800°C; under these conditions

Jan 1, 1969

By E. Ryba, D. J. Michel

SAMPLES of REZn2 (RE = rare earth) intermetallic compounds prepared by a variety of techniques have been shown to exhibit an extensively twinned micro-structure.1-4 We have recently conducted compression tests at room temperature on specimens of HoZn2 prepared by a powder metallurgy technique.' The microstructures of specimens before and after testing are shown in Fig. 1. The "before" specimen, Fig. l(a), shows the basic twin structure of this material. Fig. l(b) shows the microstructure of the "after" specimen just below the fracture surface and reveals considerable cross-twinning as well as additional

Jan 1, 1970

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted.) BLACKNER, L. A., Capt., Engineers, U. S. A., 217th Engineers (Sapper) Regiment, Camp Beauregard, La. BURKE, JAMES M., Flying Ensign, Naval Aviation. HENNIGER, WALDEMAR F., U. S. Army. JENNINGS, E. B., 2d Lieut., A. S., S. R. C., Aerial Observer. KERNAN, THOMAS, H., U. S. Army. LINTNER, E. J., 2d Lieut., Coast, Artillery. MAZANY, M. S., Lieut., 214th Engineers, Camp Custer, Mich.

Jan 2, 1919

By Norman Brown, Victor V. Damiano

ThE present paper proposes a mechanism of dislocation multiplication at internal inclusions or cavities and presents experimental evidence of such sources in zinc. Using an etching technique recently described by Damiano, Tint, and Herman1 to study the three-dimensional aspects of dislocations in bulk zinc crystals, an investigation was made of helically shaped and closed-loop etch patterns found to be associated with inclusions. Crystals containing 0.1 pet Cd and grown from the melt were deformed slightly by bending and then aged at room temperature to precipitate cadmium at the dislocations. The crystals were cleaved along the (0001) plane and then etched with Gilman's2 etch. Crystals were continuously viewed on the (0001) plane while the etching was in progress and numerous helical and closed-loops etch patterns were continuously recorded as shown in the sequences printed directly from the cine film in Fig. l(a) and (6). These etch patterns are not to be confused with the etch patterns previously reported by Damiano and Herman3 which revealed dissolution spirals on the (0001) plane of high-purity zinc crystals. In the present case, precipitates arranged in the form of closed loops or helicies are progressively uncovered by etching after suitable aging of cadmium doped zinc crystals. Viewed with dark-field illumination as shown in Fig. 2, portions of a helical figure and subboundaries were revealed simultaneously. Continuous viewing while the etching was in progress revealed in Fig. 1(b) that the short line segments observed on single photomicrographs were in fact continuous and described a helix which had its terminus at an inclusion. The observations suggested that a dislocation once nucleated at the interface between the inclusion and matrix may act in such a way as to produce ad-

Jan 1, 1964

By Henry M. Howe

Jan 1, 1908

By A. H. Daane, J. J. Hanak, F. H. Spedding

IN the study of the rare earths at the authors' laboratory, methods have been devised for preparing pure rare earths and many of their properties'- have been determined. Very little information is found in the literature on the properties of europium metal, which is the scarcest of the naturally occurring rare earths. Since we have recently prepared europium in appreciable quantities, we are in a position to describe the method of preparation and some of the properties of this metal. Metallic europium was first prepared by Klemm and Bommera who heated a mixture of potassium and EuC1, in vacuo, and obtained a mixture of europium metal and KC1. Trombe4 electrolyzed a molten salt bath containing NaC1, KC1 and EuC1, and collected the europium in a molten cadmium electrode as a cadmium alloy. The cadmium was subsequently removed by distillation but the properties of the residue indicate that pure europium was not obtained. McCoy attempted to prepare europium by distilling mercury from europium amalgam, but the stability of the Eu-Hg intermetallic compounds prevented a complete separation of the two elements. The preparation of very pure europium was suggested by previous work in this laboratory1,4 in which ytterbium and samarium were prepared by heating the respective sesquioxides with lanthanum metal turnings to 1450°C in vacuo and distilling ytterbium and samarium from the mixtures. Subsequently, small test experiments showed that europium also could be prepared by this method. A more detailed version of this method was used in the work described in this paper. Klemm and Bommer3 found by X-ray analysis that the metal had a body-centered cubic (bcc) structure with a lattice constant a, = 4.582 ± 0.00A (converted from kX units), with a bulk density of 5.30 g per cu cm. They found europium to be weakly ferromagnetic. Spedding, et al,7 found a,, to be 4.606 ± 0.001A. Barrett' showed that the bcc structure persists throughout the temperature range 5 to 3000K with a, at 5, 78, and 300°K being 4.551 ± 0.003, 4.551 ± 0.004 and 4.577 ± 0.001A, respectively. Trombe1 described europium as being iron gray, malleable, about as hard as neodymium and not attacked by cold water. He estimated the melting point to be between 1100 and 1200°C. Previous work in this laboratory indicated that the pure metal corrodes rapidly in air and reacts with cold

Jan 1, 1959

By James E. Hoffmann, John A. Bonucci, Peter D. Parker

A hydrometallurgical process has been developed for the recovery of high-purity silver from sulfated residues. The process eliminates the high temperature operations ordinarily associated with silver recovery and refining. The crux of the process is a metathetical leach which maintains the sulfate ion concentration at a level which both allows silver nitrate to be freely soluble and simultaneously depresses the solubility of lead nitrate. The subsequent hydrolytic purification of the silver nitrate solution, the recovery of high-purity silver by electrowinning in a diaphragm cell, and the final product purity are discussed.

Jan 1, 1981

By N. H. Mannakee

[Secretary's Note.—At the Spokane meeting of the Institute, in discussion of President Brunton's address on "Modern Progress in Mining and Metallurgy in the Western United States," and at the request of members present, Mr. Ayres gave an oral account of his new separator, which is here published as an independent paper, partly because of its inherent importance and partly because it describes an improvement which did not originate in the Western United States, and therefore does not fall, strictly speaking, under the title of President Urunton's address.—R. W. R.] A brief history of the growth of the anthracite-coal preparation will give a better view-point from which to judge the present problem of separating slate from coal. At the beginning of the commercial value of anthracite, 70 years ago, only the pure portions, or " splits," of the veins were mined and shipped to market, and without any preparation or screening other than the selection, while loading, of the glassy lumps, and the rejection of the fine material and the slate that had strayed accidentally into the coal. The next step was the crushing or breaking of the coal (hence the name "breaker" as applied to the preparation-building), and the sizing of it by means of bars or revolving screens. This stage of its development marked the advent of the " breaker-boy " as a slate-picker, with his ever-increasing capriciousness. As the richer veins or a splits " became exhausted and the market demanded a still greater output, the less-pure " splits " and the thinner veins were utilized to produce the coal. Carrying as they do a far greater percentage of impurities, particularly when removing the pillars, it became necessary to build new and better equipped preparation-plants. Finally, we are now at the highest stage of complicatioii yet known to the art of coal-preparation. We are dealing with varying specific gravities, frictional difference, hardness, structure, and form in the pieces of coal and slate coming from many different veins, and

Jan 1, 1910

By H. l. Burghoff, C. H. Mathewson

THE study of the creep of metals under conditions of prolonged loading has received the attention of many investigators for several years and almost innumerable papers have been published on the various aspects of the subject. As it appeared that much could still be learned from a study of single crystals, the present work was carried out to study the effects of temperature and conditions of loading upon the properties and deformation in tension of single crystals of alpha brass containing about 70 per cent copper and 30 per cent zinc. In particular, it was hoped to obtain information from tests below and above the recrystallization temperature of the material, so that properties such as elastic limit, yield point or critical stress, and manner of deformation might be compared for tensile tests at an ordinary loading rate and for prolonged. loading. Accordingly, short-time tensile tests and creep tests were made at room temperature, 300º, 500° and 700°F. The two latter temperatures are above the lowest possible recrystallization temperature of polycrystalline 70-30 brass. PREVIOUS WORK Clarke and White1 have made creep tests of some copper-zinc alloys, including 70-30 brass, and copper-zinc-tin alloys at temperatures both below and above the recrystallization temperature of the materials considered. Hanson and Wheeler have studied the flow and fracture of single crystals of aluminum for short-time and prolonged tensile loading over a range of temperature extending from room temperature to 400°F., their experiments being made without consideration of the orientations of the test specimens. Extensive creep and fracture tests on single crystals of lead at room temperature have been made by Betty3 and by Baker, Betty & Moore.4 Results of the last-named investigation were published while the present work was in progress. Millers examined the elastic limit of zinc single crystals at and above room temperature by means of creep tests, while Miller and Milligan6 reported the results of tests designed to show the influence of temperature on elastic limit of single crystals of aluminum, silver and zinc. The behavior, of iron crystals under static tensile loading at room temperature was reported by Gensamer and Mehl7 while the present investigation was in progress. Their specimens exhibited a well-defined yield point, below which no appreciable creep could be detected. The manner of yielding proved interesting, as the shape of the creep-time curve for the iron crystals differed from the common type of creep curves. Elongation did not begin immediately, or at least was initially very slow. The rate of elongation then increased continuously and finally decreased to zero. This S-shaped type of elongation-time

Jan 1, 1941

By Charles Hart

THE art of electric smelting came with the turn of the present century and owes its existence to the introduction of alter-nating current, which found its first wide use in the establishment of the great power plants at Niagara Falls, N, Y. Prior to that time current was largely direct. The fur-naces were electrolytic in nature and found their first metallurgical use in the produc-tion of aluminum, and this process still prevails. The normal production of pig iron up to that time was carried on in blast furnaces in which charcoal, coke and anthracite were used as the fuel. This new electric process called for sufficient carbonaceous material to reduce the oxides and impregnate the pig iron with sufficient carbon, but the remainder of the energy was to be supplied by electric power. The chemical reactions are essentially the same in electric smelting as obtains in the older blast furnace. All of these data are so well known in both methods as to need no discussion at this time, for they can be found in scientific publications and books written during the first two decades of this century.

Jan 1, 1940

By G. A. Reinhardt, H. J. Cutler

ThE Youngstown Sheet & Tube Co. has produced a large tonnage of 0.35 to 0.45 carbon forging steel, the acceptance of which was based on the physical properties of test specimens obtained by forging the original 5 3/4-in. (14.5 cm.) square bloom to a 3/4-in. (1.9 cm.) round. Annealed and tempered specimens were required. The test bars were annealed by heating from 900" to 950' C. and cooling slowly in mica. The test bars were tempered by heating to 825' to 875" C., quenching in water, and drawing to 515" to 535" C. Immediately after heat treatment, the test pieces were machined to a diameter of 0.534 in. (1.38 cm.) and tested. Very good physical properties were obtained and no difficulty was experienced in meeting the specifications called for. UlTimate Strength.. Elongation, Lb. pER Sq. In. PEE Cent.. in 4 In. Not LeEs Than Annealed specimens.............. 78,230 to 92,450. 18 Tempered...................... 120,000 to 149,350 9 After experience on this material, production of slightly higher carbon forging steel was started. The method of testing this material required that test blooms be either normalized or annealed. The normalizing consisted in heating to 850" to 900" C. and cooling in still air; the annealing, in heating to 850" to 900" C. and cooling in the furnace or in mica. From the treated bloom, the test pieces were taken either by core drilling or by sawing from points midway between the edges and the intersection of the diagonals. The cores or blocks were turned to a standard 2-in. test piece with a diameter of 0.564 in. and tested without further treatment. The physical requirements of the test pieces were: yield point, pounds per square inch minimum, 44,800; ultimate strength, pounds per square inch, 89,600 to 112,000; elongation, per cent. in 2 in. not less than 17. Difficulty was encountered as soon as work on this material was started. Many precautions and refinements were instituted but it was found very difficult to secure the required elongation.

Jan 1, 1920

By J. K. Brooke, F. A. Renninger

During 1966, crushed stone production in the United States totaled just over 811 million tons valued at almost $1.2 billion. This represented in- creases of 4 % in tonnage and 5 % in value over that for 1965. Excluding the crushed stone used for agricultural and certain industrial purposes (cement, lime and flux), crushed stone mineral aggregate production totaled 616.3 million tons valued at almost $910 million, also up roughly 4% in tonnage and 5% in value over the 1965 figures. Limestone was by far the most widely used rock variety, followed by basalt, granite and sandstone in that order. Concrete aggregate and roadstone continued as the main uses for stone, accounting for 63% of all tonnage produced in 1966 and 60% of total stone value. Sand and gravel production in 1966 increased 3% over that for 1965. Total 1966 output was just in excess of 934 million tons valued at almost $985 million as compared with 908 million tons at $957 million for the previous year. Excluding the higher valued industrial sands, 903.2 million tons of sand and gravel valued at $891.6 million were used directly as mineral aggregates, representing a 2.9% increase in tonnage and a 2.4% increase in value over 1965.

Jan 2, 1968

By George F. Sawers

THE geophysical methods of exploration employed so extensively in mining and petroleum investigations are now being used in civil engineering. Requirements differ from those of mineral exploration and therefore modified techniques have been developed.

Jan 8, 1953

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By R. M. Keeney

Jan 1, 1915

By R. W. Kobler, D. A. Dahlstrom

Since the development of the pelletizing process in the fifties for relatively high purity pellets from low grade taconites, there have been several distinctive changes in filter construction for the dewatering step preceding balling. In the original large pilot plant run by Reserve Mining Co. in Babbitt, MN, the disk type filter employing agitation (Agidisc filter) was selected as the most economical. Size was limited to 2.1 m (6 ft, 9 in.) in diameter. The second generation occurred in the sixties with a jump to 2.70 m (8 ft, 10 in.) in diameter to reduce capital costs per annual ton of pellet. In the early seventies, the third generation was the steam drying disk filter which became necessary to achieve balling moistures with specific surface areas of 2200 cm2/g to as high as 3800 cm2/g caused by finer grinding to obtain higher purities. Finally, the fourth generation has recently been developed to reduce maintenance costs and further improve hydraulics to ensure minimum moisture contents.

Jan 1, 1980

By S. Tiwary, S. Samanta, B. N. Pandey, N. C. Saxena, R. Sinha, B. P. Nandy, B. Singh

Subsidence investigations over one bord and pillar and one longwall caved panel at Dhemomain colliery showed that, although the width-depth ratio (0.82 and 0.83) and working and strata conditions were almost identical, the maximum subsidence over bord and pillar panel was 46.2 per cent of extraction thickness against only 6.9 per cent over longwall panel. The angle of draw was 13O to 210 and 66 to 95 per cent of the subsidence had taken place immediately after extraction. The subsidence profiles were not symmetrical and were of funnel like shape. There was wide variation in subsidence movements over caved faces in India mainly due to difference in the composition of supercumbent strata.

Jan 1, 1983

By T. G. Madgwick, A. Beeby Thompson

FoR more than 2500 years, natural gas issues in the Surakhany district of the Apsheron peninsula were the object of pilgrimages by fire worshippere and Hindoos from Burma and India. Even as late as 1890, Hindoo priests conducted ceremonies in a temple at Surakhany, which probably replaced a more ancient one; but later, the visits of the pilgrims were prohibited in order to check the spread of Asiatic diseases in that region. For centuries, limited supplies of oil have been abstracted from shallow excavations in the Caspian oil belt and dispatched into the interior of Asia and elsewhere for medicinal and industrial purposes. Statistics show a yield of 37,400 bbl. in 1863, but only since 1869 has there been serious development; in that year the yield was 203,000 bbl. At that time, hand digging was supplanted by drilling, and the enormous wells that resulted from tapping sources hitherto beyond the reach of operators completely demoralized the industry for a time, owing to inadequate outlets for the products. The early activities in this area were greatly hindered by annoying taxation, monopolies, imperial land grants, etc., but when these were revoked or adjusted, in 1877, the industry sprang into prominence and, between 1898 and 1901, the Baku fields produced practically one-half of the world's supply of oil. Within a few miles of Baku lie the two richest oil fields in the world; viz., the Balakhany-Saboontchy-Romany and the Bibi-Eibat, the latter constituting almost a suburb of the city. For many years the gasoline obtained in the refineries of the Baku area was burned in pits, being considered an undesirable product, and until 1870 the residue also was destroyed, its value as a fuel not being recognized. Kerosene was the main product sought by the refiners. It was shipped across the Caspian Sea and up the Volga to the industrial centers of Russia. Only on the completion of the Baku-Batoum railway did the Baku oil fields secure important commercial communication with the outside world through the medium of the Black Sea. The first tank steamer was successfully launched on the Caspian in 1879, by Messrs. Nobels, for transporting oil in bulk instead of in barrels. In 1905, an 8-in. pipe line to Batoum was completed; this was capable of transporting to seaboard 8,000,000 bbl. of kerosene per annum.

Jan 1, 1921

By D. E. Norquist, J. E. Moeller

The results of wear on marked balls, 4, 31/2, 3, and 2 in. diam are given. All balls were forged steel of practically the same chemical analysis and hardness. The results indicate that balls in a given mill for a given length of time will have equal diameter losses, regardless of size.

Jan 6, 1950