Search Documents

By R. S. Hooper

In attempting to describe recent mining developments at the Bunker Hill mine, it may be well to recall first the old days of hand mining when holes were laboriously drilled by hand to a maximum depth of three feet, and were shot one or two at a time, in order that the miner could take advantage of every slip, crack or bedding plane, and so save as much drilling as possible. Broken muck, of course, was loaded by hand shoveling into wheelbarrows or small cars, and heading advances or stope tonnages were governed by the number of men that could find room to work in any given place. The first big improvement over these old methods was the introduction of the reciprocating type of air-powered rock drill. This innovation, crude as it was, enabled the miners to set up a machine and drill a complete round of holes in one shift; but broken muck was still loaded by hand, and the size and rate of advance in headings were limited by time required to remove the broken rock. The next improvement of consequence was the appearance of the hammer-type rock drill, which greatly increased drilling speed over the reciprocating type, and made possible the completion of a full cycle in one shift, by the use of crossbars in headings, and permitted drilling and mucking to be carried on at the same time. Rock drills continued to improve as time passed, and finally the smaller and more efficient mucking machines appeared on the scene, and it became possible to muck out a round of broken rock and have a clean setup for one or more drill columns and machines. A complete cycle of mucking, drilling, and blasting was completed in one shift with an average advance of five feet. These conditions prevailed for several years, but as the mine grew deeper, the distances to transport the workers grew longer, and this fact together with the shortening of the working day, soon presented the problem of attempting to complete a cycle of operations in a shift of only six hours at the working faces. Anticipating this condition, the operating heads at the Bunker Hill had started an intensive study of more and better mechanization, and over a period of comparatively few years have adopted and placed in service methods and machines that make it possible for a three-man crew to consistently advance headings seven by nine feet in cross section, at the rate of eight feet, and more, per shift, doing all the mucking, switching, drilling and loading. These improvements consist of the following major items: I. The development of a light, flexible, easily transported jumbo equipped with pneumatic columns (Fig I), that has decreased the "setting up" and "tearing down" time an average of 11/2 hr per shift, Or 25 PCt of the available working time. These jumbos were developed at the Bunker Hill mine by members of the staff and consist of two pneumatic columns attached to a suitable carriage. They fold

Jan 1, 1949

John Birkinbine, Philadelphia, Pa.: We have in the Institute two Dudleys—Dr. Charles B. Dudley, who has so thoroughly studied the chemical composition and physical behavior of rail-steel, and Dr. P. H. Dudley, whose investigations and

Jan 1, 1900

By H. P. Moore, R. W. Fenn, Harold Margolin, W. R. Hibbard

DEFORMATION lines, also called etch markings or strain markings, are noneffaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries.1 Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrette to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation required for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted deformation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson' observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brick9 noted that deformation lines in 70-30 brass apparently associated with {111} planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards11 reported that in copper cold rolled less than about 50 pct few strain markings were apparent but for higher. reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass

Jan 1, 1948

By Hsun Hu, R. S. Cline

In an earlier publication1 it was shown that a single crystal of Cu-4 wt pct Al cold-rolled in the (110)[112] orientation was stable up to 95 pct reduction, although the orientation spread was considerable larger than in a similarly oriented and cold-rolled copper single crystal. When rolled to 99 pct reduction, the copper crystal retained its initial orientation and a high degree of sharpness of texture, whereas the Cu-4 pct

Jan 1, 1969

By W. W. Mason

The US began exporting coal in the late 1800s, at first in very small quantities to Canada and, beginning in 1897 and 1898, to the east coast of South America. Shipments to European countries began on a very limited basis in 1902 and these shipments increased gradually until World War I when shipments overseas increased from 7.3 Mt/a to 20 Mt/a. After the war exports dropped as fast as they had increased and, with the exception of exports to Canada, remained at very low levels until just after World War II when the US again emerged as a major coal exporter. World War II left the coal industries of Europe in ruin. As the US was the only country able to supply large quantities of coal at reasonable prices needed for reconstruction of the European economy, the US coal exports overseas expanded rapidly to 38.6 Mt in 1947. Additionally, we shipped 23.8 Mt of coal to Canada in that year for a total export of 62.3 Mt. Unfortunately, that level was not reached again until 1957 when exports reached an all-time high of 69.3 Mt - a high that has not been reached since. Over the years the level of US coal exports has fluctuated fairly widely. Approximately 80-90% of all US coal exports are high quality metallurgical grade coal so our exports level depends directly on world-wide economic conditions and world steel production levels.

Jan 1, 1982

By D. A. Martin, Laird Crocker, W. I. Nissen

The Federal Bureau of Mines has developed a process for removing SO2 from stack gases. The process comprises absorption of SO2 in an. aqueous solution of sodium citrate, citric acid, and sodium thiosulfate, followed by reaction of the absorbed SO2 with H2S to precipitate sulfur and regenerate the citrate solution for recycle. A pilot plant was operated at The Bunker Hill Co. lead smelter in Kellogg, Idaho, to assess the feasibility of using the process for flue gas desulfurization. Nominal capacity of the pilot plant, which treated .tail gas from the lead smelter sintering furnace, was 1699 standard meters cubed per hour (15 degrees celsius) of 0.3- to 0.7-percent-SO2 gas yielding about 272 net kilograms of sulfur per day. The pilot plant was operated for about 4500 hours and produced more than 45 net tonnes of sulfur. The operation demonstrated that (1) more than 95 percent of the SO2 could be removed from the lead smelter sintering furnace tail gases, (2) regeneration of the citrate solution with H2S and precipitation of sulfur in conventional stirred vessels was readily controlled and highly efficient, (3) the precipitated sulfur could be continuously recovered as a 99.5-percent-pure product by kerosine flotation and melting, and (4) the 77- to 79-percent-H2S gas used for sulfur precipitation could be readily produced from pilot plant product sulfur, natural gas, and steam. Projected operating costs, including capital charges, for a citrate plant, installed at a 118 000-tonne-per-year lead smelter and treating 49 271 standard meters cubed per hour of lead smelter sintering furnace tail gas, are estimated to be $384 per tonne of sulfur.

Jan 1, 1976

By C. S. Giggins, F. S. Pettit

The oxidation properties of Ni-Cr alloys with fine grains, coarse grains, and deformed surface layers have been studied at temperatures of 900" and 1100°C in 0.1 atm of oxygen. The oxidation rates of alloys containing between 10 and 30 wt pct Cr have been found to be dependent upon the grain size of the alloy. Finegrained alloys had smaller oxidation rates than coarsegvained alloys because of the selective oxidation of chromium at alloy grain boundaries. In this compositional range alloys with deformed surface layers behaved similar to fine-grained alloys due to recrys-tallization of the deformed surface layer. In the preceding paper1 it was found that during the oxidation of Ni-Cr alloys, the volume fraction of precipitated Cr2O3 could be greater at alloy grain boundaries than at other areas of the alloy surface. In the case of alloys with chromium concentrations equal to or greater than 30 pct,* the volume fraction of Cr2O3 *AIL compositions are given as weight percent unless specified otherwise. precipitated at grain boundaries and within grains on the alloy surface both exceeded the critical amount required for lateral growth of the Cr2O3 particles and the surfaces of these alloys were completely covered with a continuous, external layer of Cr203 during oxidation. However, in the case of alloys with chromium concentrations between approximately 5 to 30 pct, the volume fraction of precipitated Cr2O3 exceeded the critical value required for external scale formation only at grain boundaries.but not within the interior of the grains. Consequently, the surfaces of these alloys had external scales of Cr3O3 over the grain boundaries but internal Cr2O3 subscales with external scales of NiO away from the grain boundaries. Under these latter conditions, it was found that chromium could diffuse laterally in the alloy from those areas covered with an external layer of Cr2O3, i.e., grain boundaries, to areas where the Cr2O3 was present as a subscale. This diffusion of chromium resulted in an increase in the volume fraction of Cr2O3 precipitated in the sub-scale zone and continuous layers of Cr2O3 could be formed at the subscale front in these regions. For the alloys used in the previous studies,' continuous layers of Cr2O3 were formed on Ni-20Cr alloys in the subscale regions after approximately 30 hr of oxidation at 900°C. For shorter periods of oxidation, the Cr2O3 layer was semicontinuous with the continuous portion at the subscale front emanating from points where the Cr2O3 had been formed as an external scale over alloy grain boundaries. Some lateral growth of a Cr2O3 layer in the subscale region was observed on Ni-15Cr and even Ni-10Cr alloys but this layer was never continuous after 30 hr of oxidation. These results indicate that the selective oxidation of chromium in Ni-Cr alloys with chromium contents between 5 to 30 pct may be dependent upon the grain size of the alloy. Fine-grained specimens in this compositional range should have a larger fraction of the surface covered with external Cr2O3 than coarsegrained specimens and the subscale areas required to be sealed via lateral diffusion of chromium should be smaller. It is therefore to be expected that a continuous layer of Cr2O3 can be formed on alloys in this compositional range after short periods of oxidation providing the alloy grain-size is sufficiently small. bo studieS2,3 have established that the oxidation behavior of alloys can be significantly influenced by pretreatments which produce mechanically deformed surfaces. It has been found that deformed surfaces usually promote the selective oxidation of elements in alloys and it is believed that these effects are due to rapid diffusion of elements in the deformed layer. In view of the previous results,' which showed that alloy grain boundaries may play an important role in the selective oxidation of chromium in Ni-Cr alloys, deformed surfaces may promote the selective oxidation of elements in alloys as a result of the numerous grain boundaries formed on the alloy surfaces via recrys-tallization during heating to the oxidation temperature. The purpose of the present studies was to determine the effect of alloy grain size and surface deformation on the selective oxidation of chromium in Ni-Cr alloys at temperatures of 900" and 1100°C in 0.1 atm of oxygen. EXPERIMENTAL The average grain diameter of the alloys used in the previous studies1 was not less than 0.04 mm and alloys with compositions between 5 and 30 pct chromium had average grain diameters between 0.04 and 0.14 mm. Since the oxidation kinetics were already available for these relatively coarse-grained alloys, it was desirable to use these same alloys in the present studies. The surfaces of the alloys listed in Table I of the previous paper were deformed by using a Model F S.S. White Industrial Airbrasive Unit, which delivered a controlled mixture of 25 µ Al2O3 particles in a stream of dry air at high velocity against the surface of a specimen. The amount of surface deformation produced by this treatment was not determined but a re-crystallized layer about 15 µ thick was formed upon annealing deformed specimens. The grain size at the surface of the specimens was reduced to an average grain diameter of 0.01 mm by annealing the deformed specimens, i.e., grit-blasted,

Jan 1, 1970

[ ]

Jan 1, 1942

Jan 1, 1938

[ ]

Jan 1, 1942

[ ]

Jan 1, 1942

By R. C. Hirschfeld, H. H. Einstein, R. W. Bruhn, R. A. Nelson

The objective of the model studies described in this paper is to determine the effect of planar discontinuities on the strength and deformability of a rock mass. A model material was used because it satisfied concurrently three requirements that available natural-rock samples did not: (1) low strength, which was desirable for minimizing the loads that had to be applied in the laboratory; (2) ease of producing test specimens with geometrically regular joint patterns; and (3) uniformity of the test specimens. The model tests were performed on specimens made from a single modeling material and tested under triaxial stress conditions with [u,=u,]. Results are presented in this paper for tests on specimens that had (1) a single joint set inclined at several angles to the major principal direction, including 0º and 90°, and (2) two joint sets that were mutually perpendicular, one set perpendicular to and one set parallel to the major principal direction. Several different joint spacings were used in each series. Future tests will include a series with two sets of joints that make oblique angles with each other and with the major principal direction. The results of model tests and tests on cores of jointed rock by several investigators (e.g., Müller and Pacher,l Moore,2 Krsmanovic and Milic,3 Hayashi,4 Rosenblad,5 Jaeger,6 and Lane and Heck 7, have contributed significantly to the design of these experiments, which are believed to be the first in which a comprehensive study has been made of the combined effects under triaxial loading of joint spacing and joint orientation (Fig. 1).

Jan 1, 1970

By J. T. Eash, E. M. Wise

In a previous communication1 the improvement in slrength, harden-ability and color, occasioned by replacing gold in a typical gold-silver-copper alloy by various amounts of platinum, or palladium, was discussed. In the present paper the results of further studies upon the constitution and the nature of the hardening transformation in these alloys are presented. This research may be summarized as follows: 1. The liquidus and solidus have been determined for the alloys of the palladium and platinum series. Cooling curves were utilized for determining the liquidus of the palladium alloys but this method proved unsuitable for the platinum alloys so that a novel quenching method was utilized for the latter. Both the liquidus and solidus of the palladium alloys increase steadily with the palladium content. The liquidus of the platinum alloys increases rapidly with the platinum content, while the solidus temperature increases with the platinum content up to about 14 atomic per cent platinum, but suffers no further increase with additional increments of platinum up to 20 atomic per cent at least, owing to a peritectic reaction. 2. Palladium, and even more effectively platinum, reduces the rate of grain growth. Owing to this fact and to the increase in the solidus temperature, "overheating" does little or no damage to alloys containing reasonable quantities of these elements. This is confirmed both by tensile tests and metallographic examination. 3. The excess phase present in one of the high-platinum-content alloys has been isolated and chemically analyzed and was found to consist almost wholly of platinum, gold, and copper, evidently derived from the compound AuCu, by the partial replacement of gold by platinum. 4. The variation in the solubility of this platinum-content phase in the alpha solid solution with the temperature has been determined. This

Jan 1, 1933

By Milton Ohring, Stephen M. Edelglass

THE recently determined coefficients for diffusion of very dilute impurities in aluminum are shown in Table I. Of these data the activation energies for Ag110, cu54, Mn54 and zn85 are clustered about the value of self-diffusion in aluminum; for the remaining

Jan 1, 1970

In the last decade the railroads have been making tremendous strides in the development of services for the handling of bulk materials, the equipment for handling them, and the efficiency of handling, which resulted in lower costs to shippers. Pressure differential cars, giant tank cars and covered hopper cars, high capacity transloaders, and unit trains have led to substantial advances in expeditious, efficient, and economic handling of bulk materials.

Jan 1, 1973

By J. F. Kemp

PAGE Introduction,............170 I. The Competence oF the Igneous Rocks to Supply the Materi als oF Veins,...........171 The Demonstrated Presence of the Metals in the Igneous Rocks,. . 171 The Presence of the Metals in the Sedimentary and Metamorphic Rocks, 173 Conclusions,...........175 The Abundance in Igneous Racks of Vapors or Dissociated Gases which will Yield Water on Emission and Cooling,. 175 The Sequence of Eruptions,. .. . 1 . • .. 78 The Sequence of Vein-Formations,.......1 79 Contact-Metamorphism,.........180 Pegmatites,............181 Frequency of Pneumatolitic Minerals in Veins,.. 183 Surface-Flows of Igneous Rock Unfavorable to Vein-Formation,. . 183

Jan 1, 1902

By W. P. Sykes

In an earlier paper1 the composition-temperature limits of the gamma iron phase in the iron-tungsten system were reported as approximated by thermal analyses. At that time no attempt was made to develop metallographic evidence of the coexistence of two phases in the iron-rich solid solution at temperatures between 900" C. and 1400" C.

Jan 1, 1931

By J. Van Oirbeek

The ash-fusion gas producer, blown with air preheated to a high temperature, was perfected by the Société des Houilléres de Saint-Etienne during the years 1920 to 1925, for the treatment of a mixture of ashy fuel and limestone. The temperature, about 1800° C., obtained by using hot air in running the producer, ensures the fusion of all the slag and the transformation into carbon monoxide of every particle of carbon contained in the materials treated.

Jan 1, 1937

By Jean Howard

THERE are two mechanisms by which secondary crystals can develop in bcc alloys, namely 1) impurity inhibition and 2) strip-thickness inhibition. This paper reports some studies of each mechanism; the alloys were Si-Fe, A1-Fe, Cr-Fe, Mo-Fe, and Ge-Fe, as well as iron itself. All the alloys, which were of interest as part of a program of work on soft magnetic materials, were made by a powder-metallurgy process, using carbonyl iron (Grade MCP) as the starting material. Earlier phases of the work have already been published. Work described previously1 shows how the oxygen content of the sintering. atmosphere can be used to produce silica in the material which acts as a grain-growth inhibitor. Since then it has been found more convenient to make use of the oxide in the iron powder to control the silica content of the material. The compacts are sintered in vacuum which allows a direct reaction to take place between the iron oxide and the silicon. Details are given elsewhere.4 By this method, and by suitable adjustment of the rolling schedule, material with cube-on-edge secondary crystals has been produced in thicknesses from 0.1 to 0.001 in. in iron containing from 2-1/2 to 4-1/2 pct Si. It was also found possible to process 6-1/2 pct Si-Fe to 0.001 in. This was achieved by refinement of the sintered-compact grain size by using fine-particle silicon (i.e., <200 mesh). The brittleness of the material necessitated hot rolling to 0.020 in., from which thickness cold rolling was possible. If the conditions of sintering and the cold-rolling schedule were correct (i.e., as given elsewhere4 for 3-1/4 pct Si-Fe) secondary crystals of (110) [001.] orientation could be developed. The size of the secondary" crvstals" could not be

Jan 1, 1965

By H. D. Dahl, Roger C. Parsons

In order to improve roof stability, Continental Oil Co.&apos;s research program, initiated in 1969, was directed toward defining the geological parameters that affect the severity of roof conditions in any particular area of the mine. In addition, the program was seeking to define why roof falls in the Humphrey No. 7 mine (and in northern West Virginia-southwestern Pennsylvania coal mining areas) are oriented so that they occur primarily in north-south rooms or entries. Conclusions and recommendations from this study of roof fall orientation are given.

Jan 1, 1973