Search Documents

By M. Murakami, Y. Murakami, O. Kawano

The formation and growth of Guinier-Preston zones in Al-Zn alloys containing 4.4, 6.8, 9.7, and 12.4 at. pct zn have been studied by the X-ray small-angle scattering method. Particular attention was paid to the effects of small amounts of third elements silver, silicon, and magnesium on the formation and growth of G.P. zones. It was noticed that an appreciable number of G.P. zones were formed during the course of rapid cooling and that the size, volume fraction, and number of these G.P. zones were influenced by the existence of the third elements. During subsequent aging it was also found that the addition of both silver and silicon lowered the temperature for the growth of G.P. zones, whereas the addition of magnesium raised it. These results were explained in terms of the mutual interactions among zinc atoms, vacancies, and the third elements. A number of studies on the formation and growth of Guinier-Preston zones in Al-Zn alloys have been reported.1-4 Panseri and Federighii have found that the initial stages of zone growth take place at temperatures as low as around -100°C. For investigation of the mechanism of the initial stages of zone growth, growth studies must be carried out at low temperatures. In order to investigate the possibility of the formation of G.P. zones by the nucleation mechanism or the spinodal decomposition during quenching which was reported by Rundman and Hilliard,5 the examination of the as-quenched structure must be performed. In this paper the investigation of the early stages of the formation and growth were determined by means of the X-ray small-angle scattering method. With this technique, change of X-ray scattering intensities was measured while quenched specimens were heated slowly from liquid-nitrogen temperature to room temperature. At as-quenched state and after heated to room temperature, investigation of zone size, volume fraction, and zone number per unit volume was carried out. Measurements on these specimens yielded information on the early stages of zone formation and growth. Measurements were made also on specimens quenched to and aged at room temperature. From these measurements the previously reported model6 for the later stages of growth is confirmed; namely, the larger zones grow at the expense of smaller ones. Three elements, silver, silicon, and magnesium, were chosen as the third elements for the following reasons: Silver. In the binary A1-Ag alloy the spherical disordered 77' zones were observed immediately after quenching.7 Therefore, in the Al-Zn-Ag alloys, it is suggested that silver atoms might induce cluster formation during quenching. Also, since the migration energy of the zinc atoms was found to be raised by the addition of silver atoms,' silver atoms may have a great effect of the zinc diffusion, especially during low-temperature agings. Silicon. The effects of the addition of silicon atoms were found to be marked, especially at low-tempera-ture aging. In the binary Zn-Si system, no mutual solid solubilities between silicon and zinc9 and no in-termetallic compounds10 are reported to exist. Shashkov and Buynov11 investigated the behavior of silicon atoms in Al-Zn alloys and showed that silicon was not in the G.P. zones. The interaction between silicon atoms and vacancies is strong enough to increase the quenched-in vacancy concentration.* Magnesium. Magnesium atoms are reported to trap quenched-in vacancies and after much longer aging times these trapped vacancies will become free and act as diffusion carriers.13 Therefore at intermediate aging times, the diffusion of zinc atoms in Al-Zn-Mg alloys will be slower than in the binary Al-Zn alloys, whereas at longer times zinc diffusion will become faster. EXPERIMENTAL PROCEDURE The alloys used in this investigation had compositions of 4.4, 6.8, 9.7, and 12.4 at. pct Zn with or without 0.1 and 0.5 at. pct Ag, Si, or Mg. The alloys were prepared from high-purity aluminum, zinc, silver, silicon, and magnesium, with each metal having a purity better than 99.99 pct. The analyzed composition of the specimens is given in Table I. The measurements of the X-ray small-angle scattering were carried out with foils of 0.20 mm thick. The change of the scattering intensity was always measured at the fixed scattering angle of 20 = 2/3 deg. This angle exists nearly on the position of the intensity maximum. The value of the interparticle interference function14 which has large effect in this range of angles may not change abruptly in the case of the spherical shape of small zones. Therefore, from the above considerations, it is concluded that an increase of the intensity measured at this constant angle corresponds to an increase of the average radius and volume fraction of G.P. zones. The specimens were homogenized at 500°, 450°, and 300°C for 1 hr in an air furnace. For the study of the formation and growth at low temperatures, the foil

Jan 1, 1970

By N. Brown, J. Washburn, E. R. Parker

MOST previous quantitative work on creep of single crystals has been concerned primarily with developing empirical equations for the creep curve. Although the equations used by Cottrell and Aytekin¹ and Tyndall² represented the data quite well, it was often necessary to use different values of the constants for different specimens even though they were apparently tested under identical conditions. In the course of previous work on the effect of surface coatings on creep of zinc single crystals," it was found that equal resolved shear stress frequently did not produce equal creep rates in different specimens. The work of Chalmers' in the very

Jan 1, 1954

By J. H. Swartz

During 1938 and 1939, an extensive series of geophysical surveys, employing both resistivity and magnetic methods, have been carried on in the Hawaiian Islands by the Section of Geophysics of the United States Geological Survey in cooperation with the Division of Ground-Water of the Survey and the Division of Hydrography of the Territorial Government (see Fig. 1). During this time, surveys have been conducted on the islands of Oahu, Molokai, and Maui. Two distinct types of ground-water occurrence are being investigated: (1) The basal fresh-water lens floating on underlying salt water in obedience to the Ghyben-Herzberg principle (Fig. 2); and (2) perched ground-water (Fig. 3).

Jan 1, 1940

By H. C. Brassfield, R. E. Fryxell, E. C. Duderstadt, E. A. Aitken, P. K. Conn

Permeation rates of hydrogen through are-cast tungsten were measured at temperatures from 1300" to 2600°C with hydrogen pressure differentials of 1 and 0.1 atm across isothermal membranes. Rates were nearly Proportional to square root of pressure, were inversely ProPortional to membrane thickness, and were temperature-dependent according to the equation: p = permeation coefficient in cu cm (stp)-mm per sq cm-min-atmlr2, R = gas constant in cal per mole-OK, T = absolute temperature in OK. Permeation rates of oxygen through tungsten were deternlined in the range 1965" to 2300°C and at calculated oxygen (02) pressures of 3.3 x 10-4 to 2.2 x at?n using sealed capsules containing Kmown quantities of tungsten oxide. Permeation coefficients obtained in this manner had a temperature dependency in the range of 40 to 45 kcal per mole of permeating species. Permeation coefficients for oxygen were higher than those for hydrogen in the temperature range studied. This is probably the result of oxygen solubility being much greater than hydrogen solubility at these temperatures at a gzven pressure. The purpose of this investigation was to determine experimentally the permeabilities of hydrogen and oxygen through polycrystalline tungsten at temperatures ranging from 1300° to 2600°C. Permeation rates of hydrogen through tungsten have been measured at temperatures up to 925°C,but no previous measurements have been reported for the temperature range covered in this investigation. Some diffusion measurements3&apos;&apos; and solubility measurements3 have been made for hydrogen at temperatures below 2200°C. No previous permeability studies of oxygen through tungsten are known to the authors; however, efforts have been made to determine diffusion rates5-&apos; and solubilities PERMEATION THEQRY Permeation has been defined by ortton" as the overall steady-state flow process from the gas phase on one side of a membrane or wall to the gas phase on the other side and includes the steps of adsorption, solution, diffusion, exsolution, and desorption; in a given temperature range, any of these processes may be rate-controlling. For diatomic gases, which dissociate prior to diffusion, the quantity of gas which permeates through a membrane or wall at a given temperature is directly proportional to the surface area of the membrane, the length of time of permeation, and the difference between the square roots of the pressures on each side of the membrane, and it is inversely proportional to the thickness of the membrane when diffusion-controlled, thus: q = total amount of gas permeating a membrane, p = temperature-de pendent permeation coefficient, A = area of membrane exposed, / = time, p i = gas pressure of high-pressure side, p2 = gas pressure of low-pressure side, d = thickness of membrane. When the surface reactions are not rate-controlling steps and the solution of the gas in the metal follows Henry&apos;s law, the permeation coefficient, P, is equal to the product of diffusivity and solubility. The permeation coefficient is also temperature-dependent according to the equation: Po = permeation constant, Q = activation energy, R = gas constant, T = absolute temperature. MATERIALS The tungsten materials used in this investigation were greater than 99.9 pct pure. The interstitial impurities ranged from < 1 to 50 pprn C, 7 to 35 ppm O, less than 15 pprn N, and undetectable quantities of hydrogen. Previous high-temperature studies of are-cast tungsten have shown that thermal treatment similar to that which the hydrogen permeation cells experienced reduces the carbon content from starting levels of 50 to 60 ppm to about 30 ppm. Metallic impurities were in the low (1 to 50) ppm range. The argon gas used in this investigation contained about 8 ppm N. None of the following gases were

Jan 1, 1968

By L. P. Teas

The main facts brought out by the study of the blende-bearing ores examined are as follows: 1. Chalcopyrite as minute triangular or rectangular dots, or as

Jan 1, 1918

By E. V. Manlapig, David J. Spottiswood

In recent years great advances in the automatic control of flotation plants have been made, mainly due to the development of reliable sensing instruments to monitor process performance and the development of an adequate understanding of system responses to process disturbances. Some of the control strategies used in flotation plants which apply computer control are presented here. These schemes, which involve the control of collector; depressant, frother, and air and pulp level, are analyzed with respect to their control objectives, control variables, and the instrumentation involved. The knowledge gained in understanding these strategies may be applied in the dew and implementation of control system in other concentrators.

Jan 1, 1981

By John B. Goddard, David R. Brosnahan

Leaching of uranium in situ from sandstone deposits with ammonium carbonate solution containing dissolved oxygen occurs rapidly compared with the leaching of the bulk of the sulfur present as FeS2. However, because of their high reducing capacity and their relative abundance, the FeS2 minerals consume the bulk of the oxidant. A pressure leach apparatus was constructed that permitted measuring oxygen consumption by FeS2, best described by a first-order reaction. The experimental rate constants for various cores are roughly proportional to their FeS2 contents.

Jan 1, 1983

By Nick A. Hasenack, Heinz Kister, Rolf B. Vogel, Kees H. van Toor

A full survey of the laboratory and blast furnace tests carried out on two types of acid pellets is given. From the lab tests it appears that type B has a better low temperature disintegration index and a lower reducibility index than type A. The chemical composition and swelling indexes do not differ for both types. From the blast furnace test periods, carried out with a charge of 45% of pellets and 45% of sinter, it follows that both types of pellets lead to the same pig-iron production, blast furnace permeability, and blast furnace dust production. It also can be concluded that type B pellets cause a significantly higher coke consumption.

Jan 1, 1977

By R. Stefanko, R. H. King, L. A. Morley

Coal mine fires, injuries and electrocutions, and many production delays have resulted from trailing cable splice failures. Research was carried out at The Pennsylvania State University to determine the failure causes and recommended solutions. The study revealed that current splice kit materials are generally adequate with the exceptions of connector flexibility, adhesives bonding, and abrasion characteristics of taped jackets. Research indicated that the most prevalent breakdowns result from workmanship defects. Therefore, guidelines for improved splice construction are reported in detail.

Jan 1, 1976

By Richard Klimpel

This paper describes the effects of slurry viscosity on the selection-for-breakage and breakage distribution parameters in the wet grinding of ores. A series of experimental tests were run on laboratory scale ball mills. Slurry viscosities were modified by varying the solids/water ratio with and without the presence of selected chemicals. Very consistent and predictable correlations are shown to exist. The grinding parameters were calculated using a computerized back-calculation technique developed by Klimpel and Austin. Industrial scale circuit calculations and preliminary plant trial data suggest that considerable increases in throughput and/or fineness of grind can be achieved through the judicious use of chemical additives.

Jan 1, 1977

By R. W. Smith, R. W. Lai

Very recently there has been a quickening of research effort in the field of silicate mineral flotation, particularly as regards the flotation of beryl.&apos; These studies have already contributed much to the understanding of both anionic and cat-ionic flotation of silicates. Of particular interest concerning anionic flotation has been the work done on heavy metal activation of silicates by M. C. Fuerstenau and co-workers.4,7 In addition. in the paper by Fuerstenau, Rice, Somasundaran and Fuerstenau7 attention was paid to low pH anionic flotation of beryl in the absence of activators. This subject was also covered in the papers by Avotins,3

Jan 1, 1967

Jan 1, 1936

Jan 1, 1936

By Charles W. Henderson

THE influence of mineral production on the development of the western United States has been profound. From 1848 to 1860, there was only gold production, the effect of silver began in 1860, and from then on both had a powerful influence. Lead production started in 1863, copper in 1863, and zinc in 1885, but was small until 1898. Gold alone was therefore the stimulus of the early settlement and exploration of the Western States.. But mineral deposits caused neither acquisition of territory nor determination of boundary lines. Arizona, California, Nevada, New Mexico, and parts of Utah, Wyoming, and Colorado were formally acquired from Mexico fourteen days after the actual date of the discovery (January 19, 1848)1.2 of gold at Sutters Mill, near the present town of Coloma, California (a discovery which, with the immediate new discoveries, aroused the world several months later) ; but the acquisition was by treaty (under negotiation for some time but signed February 2, 1848)3 in settlement of a war involving the boundaries of the grassy plains of Texas, an area at that time not known to contain any metals, and to date found to have but few metal deposits.4 The international boundary at 49º latitude for the far northwest states was determined by causes other than mineral deposits.

Jan 1, 1933

By P. D. Frost, H. A. Robinson, J. R. Doig, M. W. Mote

The mechanism of hardening in heat-treatable zirconium alloys was foUNd to be analogous to that for titanium alloys. Zirconium containing a relatively large addition of a ß -stabilizing element such as molybdenum or columbium can be hardened by the following transformation: Lean alloys, having insufficient alloy content to retain ß at room temperature are hardened by the following transformation: Application of these findings in Zr-Mo-Sn and Zr-Nb-Sn alloys produced strengths as high as 190,000 psi with reasonable ductility. PRIOR research on zirconium alloys has been concerned with development of greater strengths and creep resistance by solid-solution hardening or by dispersion hardening. Although solution and aging heat treatments had been applied earlier to zirconium alloys, quenching frequently produced low ductility. The possibility that the ß-to-w transformation, discovered earlier in titanium alloys,&apos; might also occur in zirconium alloys and cause low ductility was considered, and, indeed, was found as predicted2 to be the case. In the earliest experiments, the heat-treatment response of titanium, too, was disappointing. However, by avoiding the formation of the embrittling w phase, it became practical to obtain room-temperature strengths higher than 180,000 psi, with elongation values of 10 pct.3 Based on the present concept of titanium heat treatment, the principal requirement for a heat-treatable zirconium alloy is that it contains a certain minimum amount of one or more ß -stabilizing elements. Only molybdenum, columbium, and tantalum, when present in sufficient amounts, are known to stabilize ß zirconium to room temperature during rapid cooling from the ß field. Tantalum was undesirable because of its high thermal-neutron cross section. Aluminum and tin are effective a stabilizers, but aluminum has been shown to seriously decrease the corrosion resistance of simple zirconium alloys in hot water. Therefore, for the present study, tin was used as the stabilizer addition. The alloys selected for this evaluation are presented in Table 1 along with their analyses and ß-transus temperatures. The analyses indicated that intended compositions were usually realized. EXPERIMENTAL PROCEDURES All of the alloys were melted from sponge zirconium and fabricated to sheet for heat treatment

Jan 1, 1960

By J. H. Jackson, P. D. Frost, C. H. Lorig, L. W. Eastwood, A. C. Loonam

It is well known that for equal weights of material, thin sections of the lighter structural alloys are more resistant to buckling under a compressive stress than thin sections of more dense material. Therefore, structural parts having the same resistance to buckling stresses are generally lightest when they are made of magnesium alloys. Consequently, there is considerable interest in the development of strong alloys having densities equal to or lower than that of magnesium and strength-weight ratios equivalent to those of the strongest aluminum alloys. The development of commercial magnesium-base alloys has been very successful, and their importance among materials in the structural field has been amply demonstrated. However, an even wider structural application of magnesium alloys might be effected if improvements could be made in the cold rollability and cold-forming characteristics. Such improvements, along with production of less directionality in properties. could be effected if the hexagonal close-packed lattice of present alloys could be replaced with a cubic lattice. In 1942, a project, having as its objective the improvement of some of the characteristics of commercial magnesium-base alloys, was initiated at Battelle Memorial Institute under the sponsorship of the Mathieson Chemical Corporation. At that time, one of the authors,* then Chief Metallurgist for the Mathieson Chemical Corporation, postulated that the addition of lithium to magnesium in sufficient quantities to change the crystal structure of the resultant alloy from a hexagonal to a body-centered cubic lattice should produce a magnesium-rich alloy which would have the desired improvements in cold-working characteristics with less directionality in properties. To test this view, a series of alloys was made and was found to have many of the attributes that were predicted. The view that magnesium-lithium alloys were of structural interest was also held by others. In 1943 and 1945, Dean and Andersonl,² obtained patents on magnesium-base alloys containing from about 1 to 10 pct lithium, from about 2 to about 10 pct manganese, and the balance substantially all magnesium; and on magnesium-base alloys containing from about 1 pct to about 10 pct lithium, from about 2 to about 10 pct manganese, from about 0.5 to 2 pct silver, and the balance substantially all magnesium. They noted that an alloy containing 83 pct magnesium, 10 pct manganese, 5 pct lithium, and 2 pct silver could be cold rolled by any of the usual methods and that this alloy was considerably harder and stronger than most other magnesium-base alloys heretofore available. In 1945, Hume-Rothery, et al.,3 predicted that magnesium-lithium base alloys should be soft and ductile and that such compositions, to which was added a third element for the purpose of producing a precipitation-hardening type of alloy, should be ductile, strong, and lighter than magnesium itself. Hume-Rothery investigated the binary magnesium-lithium and ternary magnesium-lithium-silver equilibrium relations and criticized the existing equilibrium diagrams. The binary magnesium-lithium equilibrium diagram has also been investigated by Grube, Von Zeppelin, and Bumm, Henry and Cordiano, Sal&apos;dau and Shamrai, Hof-mann,&apos; and Shamrai.8 The work of most investigators agreed with that of Grube, whose constitution diagram is shown in Fig 1. From the standpoint of development of structural alloys, the room-temperature equilibrium relations are of great interest. An examination of Fig 1 reveals that, from 0 to 5.7 pct lithium, the existing phase is alpha, which is a solution of lithium in hexagonal magnesium. The boundary between the alpha, and alpha plus beta regions, occurs at a Mg/Li of 16.5, corresponding to 5.7 pct lithium by weight. Between 5.7 pct and 10.3 pct lithium, there exists a mixture of the alpha phase (lithium dissolved in hexagonal magnesium) and the beta phase (magnesium dissolved in body-centered-cubic lithium). The boundary of the alpha plus beta and beta regions occurs at a Mg/Li of 8.7, corresponding to a lithium composition of 10.3 pct. Much of the work described here was directed toward obtaining an alloy made up of a large proportion, or entirely, of the body-centered-cubic beta structure. In his early work, Loonam found that specimens of lithium-bearing alloys were very malleable. Ingots of alloys prepared at that time were extruded to 3/8-in. diam bars, and the mechanical properties and the effects of heat treatment were then determined. These data are given in Table 1. The outstanding ductility of the alloys, combined with their moderately high strength, evoked considerable interest.

Jan 1, 1950

By Arnulf Muan, Klaus Schwerdtfeger

Equilibrium ratios C02/C0 of a gas phase coexisting with selected phase assemblages of the system Fe-Mn-0 have been determined in the temperature range 1000" to 1300°C. The oxygen pressure for the "hfnO" +hfn30, equilibrium and for the "(Fe,hTn)O" + (Fe,Mnh 0* equilibrium at high manganese contents has been determined by electromotive force measurements using stabilized zirconia as a solid electrolyte. The notstoichometry 01&apos; "hTnO" and of "(Fe, iM1z)O" solid solutions has been determined by ther-mog-/avi?netry and by wet-chemical analysis. The data obtained are used to derive activity-composition relations in "(Fe,hfn)O" and (Fe,Mn),O4 solid solutions. WUSTITE "FeO" and manganosite "MnO" form a continuous series of solid solution at high temperatures,&apos; and so do magnetite Fe304 and the high-temperature, cubic modification of Mn304 (Ref. 2) (high hausmannite, -1170). The oxides "FeO" and "MnO" are cation-deficient phases.495 The nonstoi-chiometry of "(Fe,Mn)O" solid solutions has been studied by Engell and ~ohl&apos; at two selected C02/C0 ratios at 1250°C. The two oxide end members of the spinel solid solution, FesO4 and Mn,04, however, are known to be close to stoichiometric under the experimental conditions used in the present investigation.&apos;&apos;&apos; The oxygen pressures of "(Fe,Mn)07&apos; solid solutions in equilibrium with iron have been determined by Schenck and coworkers,8 by Foster and welch," and by ~n~e1l.l&apos; The two former groups equilibrated the condensed phases in C02-CO atmospheres of lmown compositions, whereas Engell" used a galvanic cell with stabilized zirconia as a solid electrolyte. The results of these investigators are not in good agreement. Activities of FeO in manganowiistite as calculated from the results of Foster and Welch show ideal behavior, those of Engell yield a pronounced positive deviation, and those of Schenck et 01. show a moderate positive deviation from ideality. In the present work oxygen pressures for the iron + manganowiistite and manganowustite + spinel equilibria and the nonstoichiometry of manganowiistites have been measured. The data were used to calculate activities in the manganowiistite and spinel solid solutions. EXPERIMENTAL METHODS The COz/CO ratios at which manganowustite and iron are in equilibrium were determined by thermo-gravimetric and quenching methods. Experimental details are described in a previous publication.&apos;2 In the thermogravimetric technique, incipient reduction of manganowiistite pellets to metallic iron was observed as a break in the weight vs log COZ/CO curve. In the quenching technique, manganowiistite samples were partially reduced to metallic iron, or the metallic iron of manganowustite + metallic iron mixtures was partially oxidized to manganowustite, in atmospheres of constant C02/CO ratios. After quenching the composition of the oxide phase was determined by X-ray lattice parameter measurements and comparison with a standard curve obtained from oxide solid solutions of known compositions. The nonstoichiometry of "MnO" and "(Fe,Mn)07&apos; solid solutions was determined by chemical analysis of samples equilibrated in C02-CO atmospheres and quenched to room temperature, as well as thermo-gravimetrically by reducing (Fe,Mn),04 or Mn304 to manganowiistite or manganosite. The equilibrium between manganowiistite and (Fe,Mn),04 was measured thermogravimetrically by reducing (Fe,Mn),04 solid solutions having composition in the range of %„ l(NFe +NM) from 0 to 0.63. No experiments could be performed with this technique at higher manganese contents, because the equilibrium C02/C0 ratios are too large for accurate control. An additional difficulty arises at the higher manganese contents due to the strong increase in oxygen content of the manganowustite phase with increasing log Py near the manganowiistite-spinel boundary. Consequently a sharp break in the weight loss vs log C02/CO curve cannot be observed at the phase boundary. At high manganese contents of the manganowiistite, e.g., (NMn/(NF~ + NMn) > 0.9, electromotive force measurements with stabilized zirconia as a solid electrolyte were made to determine the equilibrium oxygen partial pressure. Experimental details are described in a previous paper.* Mixtures of "(Fe,Mn)O" and (Fe,Mn),04 were pressed to pellets, and the oxygen pressure of the equilibrated samples was compared to that of Ni + NiO mixtures in the cell The composition of the manganowiistite in the equilibrated two-phase mixture was determined by lattice parameter measurements and comparison with known standards. The oxygen pressure for the Ni + NiO equilibrium was taken from available data.l3~l4 No reliable results were obtained with the electromotive force technique on iron-rich oxides. The electromotive force drifted strongly with time in this composition range. An additional difficulty arises from the partial de-

Jan 1, 1968

By H. C. Doepken

Wrought Hadfield steel was tested in axial tension at from 100° to —196°C, to determine flow and fracture stresses as well as conventional properties. Ductility and related properties, such as fracture stress, decreased continuously with temperature. Peculiarities during straining indicated possible martensite formation or mechanical twinning. THE mechanical properties of austenitic manganese steel have been summarized by Avery and Day,&apos; including the low temperature tensile properties reported by Hadfield and coworkers2,3 " These data show the material to be brittle at both liquid oxygen and liquid &apos;hydrogen temperatures. Avery and Day report considerable ductility measured by Charpy V-notch tests at —100°F (-73°C). Since the review of low temperature properties by Seigle and Brick&apos; show face-centered cubic structures, other than Hadfield steel, to be ductile at low temperatures, it was felt that a study of tensile properties, between the reported intervals, should show whether the decrease in ductility was a gradual decline or an abrupt drop beginning at some intermediate point. X-ray examinations were made in an attempt to shed further light on the mechanism of work hardening of austenitic manganese steel. The presence of a magnetic constituent has been found by Hall" and by Avery, Homerberg, and Cook." Krivobok7 demonstrated the growth of magnetic constituents on reheating cold-worked specimens. Hadfield2,3 &apos; and Goss found no a iron. The steel from which the specimens were taken was commercial hot rolled % in. diam rod of electric furnace steel. The ladle analysis was as follows: C, 1.40 pct: Mn, 12.11; P, 0.060; S, 0.012; Si, 0.120; Ni, 0.080; and Cr, 0.090. Fifteen specimens, 6 in. long, were cut from a

Jan 1, 1953

By J. A. Berge, R. S. Mateer, R. G. Aspden

IN a study of the cold-rolling characteristics of iron-base alloys with 3 to 12 pct Al, the influence of aluminum content on the cold-rolling textures was evaluated. This work was undertaken to determine if binary iron-aluminum alloys possessed cold-rolling textures similar to other body-centered-cubic alloys and to contribute additional information on the effect of solute concentration on the cold- rolling textures. Gradual changes in cold-rolling textures with an increase in solute content have been observed in copper1 and in titanium.2 Iron-base alloys containing 3.0, &apos;6.0, and 12.0 pct aluminum were vacuum-induction-melted in a magnesia crucible and permanent-mold cast. The materials used were high-purity electrolytic iron and 99.99 pct grade aluminum. Each ingot was 1 in. square in cross section by 12 in. in height. The bottom half of each ingot was soaked for 1 hr at 1000°C and rolled at 1000°C to a thickness of 0.055 in. with the long axis of the ingot parallel to the rolling direction. The strip was reheated between passes to maintain a rolling temperature of 1000°C.

Jan 1, 1960

By A. C. Spencer, H. F. Bain, E. C. Harder, Sidney Paige, C. M. Weld, W. Lindgren

At a meeting of the New York Section, on May 23, 1918, the sole subject of discussion was the nature and occurrence of iron ores in certain parts of the world." Owing to the importance of this subject, it has been deemed advisable to publish the remarks made at that meeting in the form of a paper, for presentation at the Milwaukee Meeting. The remarks related to the following districts: Page Brazil. By E. C. Harder................................. 116 Scandinavia. By Waldemar Lindgren..................... 120 Cuba. By C. M. Weld.................................. 124 Southern Europe. By A. C. Spencer...................... 130 China. By H. Foster Bain............................... 132 Alsace-Lorraine. By Sidney Paige......................... 135 Brazil BY E. C. HARDER† During the years immediately preceding the war, the iron ores of Brazil were attracting the attention of iron operators both in Europe and in the United States. This was due to the large quantities of practically undeveloped ore available, and to its great purity. It is reasonably safe to state that had capital not been diverted from the exploitation of these deposits to war purposes, Brazilian iron ores would probably now be offered in European and American markets. It is certain that after the war these ores will play a prominent part in the economic reconstruction of Europe and perhaps in the development of America. The Brazilian iron-ore field ranks among the six great iron-ore districts of the world, the others being: (1) The Lake Superior district of the United States; (2) the Lorraine ore field of northern France and southern Germany; (3) the magnetic deposits of northern Sweden; (4) the ore fields of Oriente, Cuba; and (5) the Wabana ores of Newfoundland. It is doubtless the greatest known undeveloped iron-ore district in the world. The Brazilian iron ores are situated in the State of Minas Geraes, the center of the district being located about 250 miles in a direct line west of

Jan 1, 1920