Search Documents

By Lester C. Uren

With the depletion of our older, and relatively shallow, oilfields and the necessity for securing new production from deeper horizons, much attention is being given to the improvement of oil-well pumps in order that they may function satisfactorily under the more difficult conditions imposed by increased depth. Until recently, practically all of the world's petroleum was secured from wells less than 3000 ft. deep, whereas horizons are now being explored to depths of from 5000 to 7000 ft. in some of the more prolific fields, and it seems probable that the greater part of the future supply must come from depths in excess of 3000 ft. While much of the early production in a new field is obtained by natural-flow methods, when the stimulus of high gas pressure fails, recourse must be had to some method of pumping. The perfection of a pump capable of economically and efficiently lifting oil from depths ranging from 3000 to 7000 ft. is therefore a matter of prime importance to the oil-producing industry. This paper is offered as an estimate of the present state of development of the oil-well plunger pump and as a review of the general principles involved in its operation in deep-well pumping. A design for a new type of oil-well pump embodying several novel features, is also described. Essential Parts of Oil-well Plungeb Pump The pump commonly used in lifting oil from wells in American practice is of the simple displacement type, in which a plunger equipped with a working, or traveling, valoe is given a vertical reciprocating motion in a stationary working barrel. The latter is suspended from the surface by tubing, submerged in the well fluid, and is equipped at its lower end with a stationary standing valve; Figs. 1 and 2 illustrate two common types of oil-well pumps. The simple cup-leather packed plunger of Pig. 1 has its counterpart in the long, hollow, cylindrical, polished steel plunger of Fig. 2; otherwise the two types are identical in the form and arrangement of their essential parts. Fig. 2 shows the additional feature of a "garbutt

Jan 1, 1927

By Terkel Rosenqvist

Few subjects in iron metallurgy and steelmaking have caused so much discussion and have resulted in so many divergent and partly contradictory statements as the theory of the distribution of sulphur between molten iron and slag. An interesting survey of the different points of view is given by Grant and Chipman.1 Grant and Chipman themselves conclude in their paper that, at least in the open hearth and electric steel furnaces, the governing reaction is a simple distribution like: FeS steel ? FeS alas [Ia] and MnS steel ? MnS alas [Ib] They conclude that no significant reaction takes place according to the more classical scheme: FeS steel + CaO slag ? FeOslag + CaS slag [2a] This is the reaction which is regarded by most investigators as the primary sulphur reaction in the blast furnaces, where it is accompanied by the reaction with carbon: FeO slag + C ? Fe + CO [2b] The writer suggests an alternative to the reactions mentioned above. It is the opinion of the writer that the a priori assumption of defined molecular compounds being present in molten steel as well as in molten slag, has retarded rather than promoted a solution of the sulphur problem. As for the constituents of molten steel, it is taking too much for granted to mention the presence of FeS and MnS. If this infers that the melt contains diatomic molecules, the statement must be made that at least such molecules do not exist in the solid state at room temperature. Solid FeS crystallizes in the nickel-arsenide structure, and MnS (high temperature form) in the sodium-chloride structure. In these structures the sulphur is surrounded by six metal neighbors, and no molecular groups can be isolated. When sulphur is dissolved in molten steel, it is expected to maintain the same coordination number as in the solid state. We know that sulphur in steel has a certain chemical potential and a chemical activity which can be expressed by the reaction: S steel + H2 ? H2S where the activity A. is proportional to the ratio PH2S/Ph2. We know also that this activity is influenced by the presence of other constituents. For instance, there is reason to assume that carbon and silicon increase the sulphur activity and manganese decreases it. However, the exact relationship here is scarcely known, and further investigations are needed. Concerning the molten slags, if anything should be assumed a priori it would be that they are composed of ionic rather than molecular parts. There are indications of this in that solid silicates form ionic structures, and molten slags show high electric conductivity and can be electrolyzed.2 It has been claimed by Taylor and Chipman3 that their activity investigations

Jan 1, 1949

By Terkel Rosenqvist

Few subjects in iron metallurgy and steelmaking have caused so much discussion and have resulted in so many divergent and partly contradictory statements as the theory of the distribution of sulphur between molten iron and slag. An interesting survey of the different points of view is given by Grant and Chipman.1 Grant and Chipman themselves conclude in their paper that, at least in the open hearth and electric steel furnaces, the governing reaction is a simple distribution like: FeS steel ? FeS alas [Ia] and MnS steel ? MnS alas [Ib] They conclude that no significant reaction takes place according to the more classical scheme: FeS steel + CaO slag ? FeOslag + CaS slag [2a] This is the reaction which is regarded by most investigators as the primary sulphur reaction in the blast furnaces, where it is accompanied by the reaction with carbon: FeO slag + C ? Fe + CO [2b] The writer suggests an alternative to the reactions mentioned above. It is the opinion of the writer that the a priori assumption of defined molecular compounds being present in molten steel as well as in molten slag, has retarded rather than promoted a solution of the sulphur problem. As for the constituents of molten steel, it is taking too much for granted to mention the presence of FeS and MnS. If this infers that the melt contains diatomic molecules, the statement must be made that at least such molecules do not exist in the solid state at room temperature. Solid FeS crystallizes in the nickel-arsenide structure, and MnS (high temperature form) in the sodium-chloride structure. In these structures the sulphur is surrounded by six metal neighbors, and no molecular groups can be isolated. When sulphur is dissolved in molten steel, it is expected to maintain the same coordination number as in the solid state. We know that sulphur in steel has a certain chemical potential and a chemical activity which can be expressed by the reaction: S steel + H2 ? H2S where the activity A. is proportional to the ratio PH2S/Ph2. We know also that this activity is influenced by the presence of other constituents. For instance, there is reason to assume that carbon and silicon increase the sulphur activity and manganese decreases it. However, the exact relationship here is scarcely known, and further investigations are needed. Concerning the molten slags, if anything should be assumed a priori it would be that they are composed of ionic rather than molecular parts. There are indications of this in that solid silicates form ionic structures, and molten slags show high electric conductivity and can be electrolyzed.2 It has been claimed by Taylor and Chipman3 that their activity investigations

Jan 1, 1949

By Richard Franchot

DISCUSSION of a paper is sometimes more in-teresting in what has not been said than in what is said. In the present case the paper is mainly directed to certain thermo-dynamic relation-ships in the blast furnace. Careful reading of the dis-cussion fails to show a single use of the term, heat unit, or its equivalent. If we wish to know very-much about the furnace action it is necessary to count calories or B.t.u. Nothing much is. said about the availability of heat at high temperatures, although it will be generally admitted that in seeking underlying limiting factors in the furnace economy the hearth heat relations offer-the most promising clues. Those discussing the paper, with exceptions of course, apparently have failed to recognize an outstand-ing fact. It is a fact that the heat actually generated by the air oxygen in CO formation (including the blast heat) is in excess, after charging off radiation, etc., by from 70 to .90 per cent over the heat absorbed in melting the iron and slag and calcining the stone reduction by CO absorbing no heat. The fact stands out as plainly as does the fact that the furnace functions largely as a gas producer. The surplus heat is there. It is in the picture. Why not take a look at it, face the fact? That the surplus heat is necessitated by the hearth conditions admits of very little if any doubt. The furnace is really two separate pieces of apparatus: the hearth, doing certain work, and the superimposed shaft, doing certain other work. The combustion of fuel in the hearth, primarily serving the hearth pur-poses, generates much more heat and gas than the shaft requires, or can use, in smelting work. The result is surplus heat makes still more gas in the heat-absorbing reaction between CO, and coke; what is left of the surplus going to top heat. Here we have a simple yet adequate sketch of the furnace action. Having obtained a fairly comprehensive view of the existing heat relations of both hearth and shaft, the way to improvement seems quite plain. Either do more of the work above the hearth or put more heat into the hearth. Since there is already a great surplus of heat above the hearth, probably little needs to be done by way of increasing the proportion of the work done in the shaft. The shaft can, however, probably do much more work than it is now doing provided that a way, can be found to get more work, done in the hearth. The hearth heat is nicely balanced. Losses by radiation and water cooling and other losses are already taken care of. Any increase of hearth heat development could be utilized in taking care of increased smelting work. Aside from the possibility of increased blast heat, there is one sure way of putting more heat into the hearth, and this is to blow more air. And since the shaft already has more gas than it needs, the increased gas resulting from the greater blast volume can be withdrawn from the bosh after it has done its work in the hearth. Now an increase of burden will cool the shaft, cut down solution loss and thereby supply addi-tional coke in the hearth to burn with the additional air blown. The hearth heat per pound of coke charged will be proportionately increased. The balance between hearth and shaft will be better. Gruener's ideal will be more nearly attained, if not exceeded. Most inter-esting of all perhaps, the more the burden is increased, the more coke will reach the hearth and the more burden can be added. The effect is to be cumulative.

Jan 3, 1927

P. W. BRIDGMAN.-Owing to a misunderstanding, I did not see Dr. McAdam's and Dr. MacGregor's remarks on my paper on Flow and Fracture (Metals Technology, December 1944, Pp. 32-38), until after their publication. Both Dr. McAdam and Dr. MacGregor speak of my analysis for the stress distribution at the neck of a tension specimen as containing several assumptions; in particular, that the strain is uniform across the section of the neck, that there is no hoop tension at the periphery, and that the plasticity conditions of von Mises hold. As far as the mathematics goes, the situation is no different in this problem of plastic flow than in a conventional problem of elasticity. That solution is unique which satisfies the boundary conditions on the stresses, the stress equations of equilibrium, and in addition the constitutive equations connecting stress and strain in the elastic case, or a corresponding set of equations, of which the von Mises relations are a special form, in the plastic case. In the particular case of the necked tension specimen I have found that there is a solution satisfying the boundary conditions, the stress equations of equilibrium, and the von Mises plasticity conditions in which the strain is uniform across the section, and there is no hoop tension at the periphery. This is therefore the solution, and the uniformity of strain and vanishing of hoop tension at the periphery are to be described as discoveries, over which the operator has no control, rather than as assumptions. The only part of the solution that can properly be described as an assumption is the von Mises plasticity condition. With regard to this it is to be noted that the condition is needed only in a much weakened form, for the analysis uses the condition only at the neck, where the strain is approximately constant. Thus, in the extreme case referred to in a footnote of my paper (p. 37, Met. Tech. Dec. 1944) the actually measured strain across the section varies from 2.4 to 2.6. Obviously it is a much weaker assumption to postulate that the von Mises condition holds in the strain range 2.4 to 2.6 than to assume it to hold for the entire range of strain from o up to 2.6, which would be necessary if the solution applied to the entire tension specimen rather than to the immediate region of the neck only. Furthermore, it is to be commented that under the special conditions of this problem the von Mises condition becomes identical with the maximum shearing-stress criterion of plastic flow; this amounts also to a weakening of the restrictions imposed by the von Mises condition. Dr. MacGregor refers to actual experiments of his own in which the strain was found not to be uniform across the neck. It is to be emphasized, however, that these were experiments on bars of rectangular section, and that the nonuniformity established was a nonuniformity around the perimeter, not a nonuniformity from the surface toward the axis. My method of solution applies only to a circular cross section. It can be said that the solution that satisfies the boundary conditions, etc., would definitely not be expected to demand a uniform strain for noncircular sections. In discussing my results, Dr. McAdam uses a definition of "flow stress" different from mine, so that the immediate applica-

Jan 1, 1945

By Alexandre Mitinsky

The theory of elasticity, the science of the strength of materials, and all our calculations regarding engineering structures are based on Hooke's law, that in loaded bodies the deformations are proportional to the load producing them. Without this law it would be impossible to design intelligently engineering structures such as bridges, frames, axles, etc. This being the case, the proportional limit,l that is, the point at which deformation ceases to be proportional to load, is the most important factor in engineering design. Further, the working fiber stress should be fixed in reference to the proportional limit instead of, as is usual, in reference to the ultimate strength. The incorrect use of the ultimate strength instead of the proportional limit in setting the working fiber stress is probably due to two reasons: (1) it is a more delicate operation to measure the proportional limit; (2) it is usually assumed, though incorrectly, that the proportional limit is determined by the ultimate strength. In Germany the poin't at which permanent set first appears is often taken instead of the proportional limit. The two points will coincide if Gerstner's law, that elastic deformations are proportional to the loads producing them both before and after permanent set, is true; and the limit of proportionality and the elastic limit or point of permanent set will both be represented on a stress-strain diagram, by the point at which the line ceases to be a straight line and becomes curved or changes its inclination. It is to be further noted that the difference in definition between proportional limit and elastic limit introduces a difference in methods of determination in the testing laboratory. The German method of determining the elastic limit by alternately loading and unloading the test specimen is a lengthy process and time has in itself a very considerable influence on the results of physical tests.

Jan 1, 1916

By T. H. Troller

FOR a long time propeller-type fans have been considered a very adequate means to move great quantities of air against small static pres-sures. They have been in use for this purpose in mines, as well as in other installations. For static pressures of over 2 or 3 in. of water, the centrifugal blower almost ruled the field until very recently. Some attempts were made to use a number of propellers in line. Such arrange-ments made it possible to obtain pressures higher than 2 in. of water, but they complicated the construction and increased its expense, and the efficiencies were not improved. The more recent development of propeller-type fans has been decidedly influenced by the intensive aerodynamic research in connection with aeronautical development, which has taught us, in particular, how to use airfoils properly. The characteristic that makes an airfoil so valuable is the fact that when it moves through the air a high force component, the "lift," acts on it vertical to the motion, while the "drag" in the direction of the flow is small. The ratio of lift to drag is approximately 20 to 1 at the angles at which the profile is used in practice. An element of the turning blade, the movement of which, relative to the air, is mainly in the direction of the plane of rotation, thus experiences only a small "drag" FIG. 1.-DIAGRAM OF FORCES ON WING SECTION. opposing its rotation, and for this reason a relatively small torque is required at the driving shaft. At the same time there is a strong force component at 90° to the plane of rotation. This force is parallel to the propeller axis in the direction opposite to that of the flow of air, with a correspondingly high pressure increase.

Jan 1, 1936

By Ross C. Anderson, William I. Weisman

THE manufacture of anhydrous sodium sulphate or salt cake from natural deposits in the United States has been in general somewhat of a marginal undertaking. Competition from foreign sources and from large quantities of byproduct sodium sulphate produced domestically in the manufacture of hydrochloric acid and other chemicals has existed and continues. For example, most of the sodium sulphate produced is a byproduct or co-product in the manufacture of hydrochloric acid through the reaction of sodium chloride with sulphuric acid. In recent years, many manufacturers of rayon have installed equipment to recover sodium sulphate from waste spin bath liquors; today this is an important source. Before World War II large quantities of sodium sulphate were imported from Germany. In 1949 imported material from Europe again appeared on the domestic market. Natural sodium sulphate from Canada in substantial quantities also enters the United States markets. Despite this kind of competition, numerous attempts have been made to exploit various natural deposits of sodium sulphate in this country, but only a very few of these have survived economically over a period of years. One of these few operations is the plant of the Ozark-Mahoning Co. located 13 miles south of Monahans in West Texas. Several factors contributing to the successful life of this plant may be summarized as follows: 1—Geographical location. Monahans is reasonably close, freightwise, to the Kraft paper mills in Texas, Arkansas, and Louisiana; the Kraft paper industry is the greatest consumer of sodium sulphate in the United States. 2—Availability of natural gas as low cost fuel. Proximity of the natural gas fields of West Texas has been a tremendous asset, as the availability of low-cost natural gas is to all industry throughout the Southwest. 3—The nature of the deposit. The occurrence of sodium sulphate brines in southeastern New Mexico and West Texas has been very well described by Lang,' who writes that the brines are found in the Castile formation of the Delaware basin. Here weathering has altered the anhydrite so that a relatively porous gypsiferous zone overlies a dense impervious mass of anhydrite. This porous zone provides traps where percolating ground waters that have picked up soluble salts may lodge. These traps or pockets are the natural brine reservoirs exploited at Monahans. Although several hundred wells have been drilled, currently some 25 wells serve to supply brine to the plant. All are within 1 1/2 miles of the plant and are conveniently tied together by an electric power system serving electric motors driving the pumps. Having the raw material in the form of a brine which can be pumped from shallow wells makes possible much simpler and more efficient handling than if it were in form of solids. By contrast, other deposits of sodium sulphate, such as those in Arizona, Nevada, and North Dakota, are in the form of the solid minerals, thenardite and mirabilite, which present somewhat more of a mining and mineral dressing problem.' The largest producer of sodium sulphate from natural sources in the United States is at Searles Lake, Cal., and there a brine also is utilized. 4—Water. Substantial quantities are needed for cooling towers and for operation of gas engines. An area underlain with brine is not a promising source of fresh water, but fortunately, after a long search, an adequate supply was found nearly two miles from the plant. It may be appropriate to discuss briefly the grades of sodium sulphate offered on the market. Salt cake is the name usually applied to the grade of sodium sulphate used by the Kraft paper industry. It may be a low analysis byproduct, 95 to 97 pct sodium sulphate, with as much as l 1/2 to 2 pct residual acid, or it may be a natural product. Usually salt cake is considered a low grade product, but a great deal of a higher grade of material is marketed under this name. The specifications for glassmakers' salt cake are somewhat higher than those of the paper industry, usually requiring 98 pct sodium sulphate. Technical anhydrous sodium sulphate is a high grade material and usually exceeds 99 pct sodium sulphate. It finds the biggest market in the textile industry and is used as a builder in some synthetic detergents. Glauber's salt, Na2SO4. 10H20, is usually of high purity. Preferred for some uses, it normally has been recrystallized from an anhydrous salt. A unique manufacturing process has been developed at Monahans. This process results in the production of an exceptionally high grade of salt cake, and qualifies for nearly all uses, including many which specify the technical anhydrous grade. All of the finished product, which is very white, passes a 10-mesh U. S. Standard screen, and is retained on a 200-mesh U. S. Standard screen. It is over 99 pct Na2SO4 with main impurities being sodium chloride and magnesium sulphate. Iron content is less than 0.01 pct. As mentioned, the raw material at Monahans is a brine drawn from wells. Attention was first attracted to this location because a so-called alkali

Jan 1, 1954

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By R. J. Cowan

In the art of cementation a controversy has been going on for years as to whether solid or gaseous carbon is the active agent in carburizing steel. More recently opinion has crystallized into a compromise to the effect that carburizing is a gaseous cementation of steel in the presence of solid carbon. The importance of this theory has a particular bearing upon the work to be described. In the art of carburizing, use is commonly made of such words as '' Catalytic" "atomic," "nascent" and "activated," in an attempt to describe the process. These words are used indiscriminately. For instance, the gas is said to be "catalytic" and carbon to be "nascent," or vice versa. In using these expressions, investigators are confirming the acceptance in their minds of the active conditions of both gas and carbon in the cementation process. Reactions at Metal Surfaces For many years attention has been directed to the consideration of reactions that occur on metal surfaces. When heated under the influence of certain metals a complex gas will be broken down and one of the constituents thereof usually found to be very active chemically in combining with the metal. The process of nitriding is an example of this type of reaction. In this case ammonia (NH3) breaks down at the metal surface and the nitrogen which is thus liberated reacts with the surface to form a nitride whereas molecular nitrogen not so liberated is inert and will not react chemically with the metal. Whatever term or terms may be used to describe such reactions, the fact remains that they are highly important and valuable in their commercial applications. Since the metal surface plays so important a part in these reactions, it is evident that any accumulation of reaction products thereon interferes seriously with the progress of the reactions. For this reason it is desirable to remove all such products as rapidly as they are formed in order to bring active gas into contact with the surface and thus facilitate the desired reactions. This is accomplished best by conducting the operation in a continuous manner, thereby causing the reacting gases to pass over the

Jan 1, 1931

Discussion of the paper of G. P. Hulst, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 92, August, 1914, pp. 1865 to 1871. L. S. AUSTIN, Salt Lake City, Utah.-One question that I would like to ask is in regard to the sampling kettle which stands beside the softening furnace. How is the sample taken or melted? G. P. HULST.-The sampling kettles in question are of 45 tons capacity and are fired with coal. The lead bullion comes in on a high line in car-load lots of 30 to 40 tons. The entire lot is trucked from car, weighed over scales and thrown into the sampling kettle, which has been previously cleaned. The kettle is fired and the bullion melted, then heated up until no frozen bullion' remains in the .bottom or adheres to the sides of the kettle. The kettle is scraped clean, sides and bottom, and the wet dross is skimmed Doff clean into molds. The kettle is stirred thoroughly during the period in which 24 to 30 samples of approximately ½ assay ton are taken. These samples are taken in a long-hand loci iron mold, providing for taking six to eight "gumdrops." The mold is inserted and heated to the same temperature as the molten metal, and gumdrops are clipped out and cooled in the mold by dipping 'the bottom of. the mold into Water. The samples should be free from fins. The gumdrops represent the contents of the kettle, and in assaying, they should not be clipped, but weighed up and the result computed. The dross bars are weighed and sawed according to old hammer and punch sample template. The sawdust represents a sample of the dross. In eases of high gold in the bullion there is a slight correction in the assay. This method of sampling was developed at the Omaha plant of the American Smelting & Refining Co., W. T.. Page, Manager, in 1903 or 1904, for adjusting differences in checking smelter sampling. L. S. AUSTIN.-The base bullion which you treat is very clean. It has been remelted, and skimmed before shipment. How rapidly can you get it through the softening furnace, and how does it compare with ordinary base bullion? G. P. HULST.-Twenty-four hours is the softening limit on these charges. In other words, it is charged into the furnace, heated up, and the first and second skimmings are taken off, and it goes into the kettle the next day; that is, 24 hr. elapse from the time the bullion is charged to the time it is in the kettle. L. S. AUSTIN.-It seems to be a long time to hold such a pure bullion. I suppose, though, it comes around conveniently so that you have a time for all the other operations of refining. Isn't that the case? MR. HULST.-Every refinery is based on those principles.

Jan 11, 1914

By Roswell Johnson

THE principle of sliding or graduation in royalties is accomplished either by the block, period, cumulative, or class method. The block method calls for a very low royalty rate on all oil produced up to. a certain amount. This amount would normally be that which is believed to suffice to repay the cost of the well. A higher rate would be charged after the well is making a profit. This method, common in many industries, is peculiarly inadaptable to any industry such as this where the productivity per day of the units gradually and inevitably decreases. This, for reasons given later, is because it forces an early abandonment of the well and so offends against conservation. In the period method, the royalty rate is changed by some definite amount when the well produces less than a specified quantity per day or other given unit of time. While simple to explain, it operates badly because a great deal is made to depend upon a small reduction in production, whereas the reduction as a matter of fact declines rather erratically owing to the exigency of lease management, connecting of tankage, and vagaries of the gaugers. These disadvantages are obviated by the cumulative method. In this method, all the production less than a certain amount per week has one rate of royalty, or none at all, and the oil produced in excess of that amount pays an additional rate of royalty. In the long run the calculation is probably no greater than with the period method, for simple tables will be published and printed in the oil papers that can be cut out, enabling quick readings to be made. Even without the table the calculation is easy with the few royalty rates, two or three, which would be used. In this method, the amount paid in royalty declines gradually, rather than suddenly as in the period method.

Jan 6, 1915

By Philip R. Strand

Vermiculite is the name used for those micaceous minerals with a ferromagnesian aluminum silicate composition and the unique property of exfoliating to a low density material when heated. Commercially, the exfoliated products are also called vermiculite, or more exactly, expanded vermiculite. In its exfoliated state, vermiculite serves many markets, chief among them construction, agriculture, horticulture, and general industry. Composition and Properties Vermiculite, in a natural state, has the characteristic mica habit, splits readily into thin laminae, flexible but inelastic. In a mineralogical sense, vermiculite is a hydrated silicate with no exact chemical composition. The structural formula for a macroscopic, trioctahedral vermiculite may be written: [ ] The structure of vermiculite is basically that of a talc, and it could be regarded as a trioctahedral member of the smectite group. Macroscopically, vermiculite displays the prominent monoclinic crystal faces that are commonly marked by lines at 60° and 120°. Hardness varies from 1.5 to 2.8 or more; specific gravities are between 2.1 and 2.8; color is amber, bronze, brown, dark green, or black. When heated quickly to an elevated tempera¬ture, vermiculite expands by exfoliating at right angles to the cleavage, into wormlike pieces (the name vermiculite is derived from the Latin `vermiculare,' to breed worms). This characteristic of expansion, the basis for commercial use of the mineral, is the result of the mechanical separation of the layers by the rapid conversion of contained water to steam. The increase in bulk volume of commercial grades is 8 to 12 times, but individual flakes may expand as much as 30 times. All expansion occurs at right angles to the basal cleavage. Vermiculite may also be expanded by a number of chemical processes such as soaking in hydrogen peroxide, weak acids, and other electrolytes. There is a color change during expansion that is dependent upon the composition of the vermiculite and furnace atmospheres. Heating in an oxidizing atmosphere produces dull gray colors. The iron is generally not oxidized during chemical expansion. The exfoliation of the vermiculite crystal results in large pores being formed between groups of platelets. Thus exfoliation can make available a large increase in void volume without significantly changing the surface area of the platelets. This characteristic is important in the chemical carrier applications of vermiculite. Although there has been much research on the chemical and structural composition of vermiculite, an exact formula and composition cannot be described. This is to be expected since vermiculite derives from a number of different mineral sources. As has been proposed, vermiculite is not a single mineral species, but families of related minerals. Additionally, commercial interest in the end product has resulted in the name vermiculite being applied to the very voluminous, bloated products from calcination of baueritized (bleached) phlogopite. This has also resulted in many names for the specific vermiculite found in a particular deposit. All of this difficulty arises from the nature of its crystal chemistry. Consequently, vermiculite is now thought of as several related variable mineral series rather than a group of related species. The vermiculites have a common silica tetrahedral sheet structure with separating ions. It is now generally agreed that vermiculites must also be regarded as true clay minerals. The properties of the mineral, such as cation exchange capacity, organic complexing ability, and vari-

Jan 1, 1975

By Frederick Burbridge

The Morning silver-lead-zinc mine of the Federal Mining & Smelting Co. is about 'two miles northwest of Mullan, Ida. The lode is a metasomatic fissure vein. The orebody is approximately 2000 ft. long within the bounds of the property and varies in width from knife edge stringers to 50 ft. It has been developed to a depth of 3600 ft. and stands nearly vertical in Revett quartzite, which .strikes north 65" west. The high-grade veins and lenses are generally mixed with waste (siderite, quartz, and quartzite). The average grade of ore to sorting plant in 1921 was 4 oz. silver per ton, 8.6 per cent. lead, and 4.1 per cent. zinc. Wall rock stands only a short time without timbering. The minimum angle of gravity flow is 45". The ratio of waste sorted out to ore is 6 per cent. No gases are generated underground and temperature has no influence on mining operations. Fresh air is forced down the air raise and up the main shaft. Drifting and Stoping Main drifts 12 ft. wide and 13 ft. high are driven every 200 ft. (vertically) and are connected by raises 125 ft. apart. These raises consist of three compartments (chute, tramway, and timber slide) and are for the purpose of ventilation, access, and hoisting supplies to stopes. Ground is stoped between raises. Chutes are placed every 25 ft. for drawing off ore broken in stopes. Waste for filling is obtained from waste raises off the stope in walls or waste is dumped from the level above down the chute compartment of raises, which is bulkheaded so that waste can be drawn off at any floor as required. Timbering Posts and caps for square sets (varying in diameter from 6 to 24 in.) are cut to length in a sawmill on the surface. No preseratives are used. Timber is taken on a flat car along drifts to a raise nearest the working place and hoisted as required. Practically no timber is salvaged for

Jan 1, 1925

By J. Parke Channing

WE are accustomed to think that we are efficient in the United States, particularly with respect to such things as mining and manufacturing. The conduct of the war has demanded in England and in France a complete readjustment of manufacturing methods and plans, and today England is probably as efficient a country as there is in the world, not even excepting Germany. This is all the more remarkable because it has been notorious for years that England has been inefficient in her manufacturing and the country has been flooded with things "Made in Germany." Today England is almost a socialistic community and the State is doing almost everything. England is now in such a position that practically everyone in the country is engaged in industry necessary for the conduct of the war, and this has been accomplished by increasing the efficiency both of her tools and of her man power. In the United States we certainly have been efficient so far as machines and perhaps so far as methods have been concerned, but we have not been efficient iii the utilization of our man power. Before the war, our labor was undoubtedly far more efficient than that of England, but it certainly was not so highly efficient as it should have been, and the problem that confronts us today, and will all the more confront us after the war, is to make our man power efficient. England has had a taste of what you may call State Socialism, and her laboring men are not going to be content to return to the old order of things. There is one feature of the labor problem in England which has permitted her to reach this condition of state socialism with comparative rapidity; this is that practically all of her laborers are English; she has little or no foreign population. While an Englishman may he a strong union man and ready to fight his employer tooth and nail, at heart he is still a British subject, and when his country was in danger he rose to the occasion.

Jan 5, 1918

By Roscoe C. Clark

In a previous technical note' by Walter Rose, evidence is offered in support of the contention that "the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely." It is not the purpose of this note to present further discussion of this possibility but rather to point out that the argument presented there does not appear to be generally valid. In the cited note' reference is made to the experiments of Welge2 wherein it was shown that when water was displaced by oil from a core the pressure in the water phase was less than in the oil phase but that when this oil was then produced by water drive the pressure in the water phase was greater than in the oil phase. Rose has concluded from these observations that conditions of static equilibrium did not obtain since the fluid saturations were such that phase discontinuities seemed unlikely. The argument from which this conclusion was drawn is based on the contention that "the pressure is always greatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase." This premise appears to have been reached from a consideration of capillary phenomena in cylindrical tubes, although it may a1so hold for other types of pore geometry, hut as will be shown below it does not hold for all pore shapes and hence is not generally applicable. Since the pore structure of porous media such as reservoir rocks i- in general so complex as to defy exact description. it is undoubtedly of great value to establish a model in terms of pore shapes of known geometry, provided of course that the limitations of the model are recognized. That the limitations of the capillary. or cylindrical, tube model have not always been fully recognized will be evident from the following discussion of a pore of different shape hut one which may a. logically he considered a.; the capillary tube. The pore space to be considered is that shown in Fig. 1, which may be thought of as the "hole in a doughnut."* Consider the interface, A-B-A', between two immiscible fluids, P, and P2, which interface meets the solid alone a line, A-C.A'-C'. The interface A-B-A' is the surface of a spherical segmen† while the line of mutual contact be-

Jan 1, 1950

By F. F. Craig

A series of both welter and gas puttern Hoods was made in the laboratory to study the oil recovery performances of .such operations. These tests were contlrrctt~tl on consolidated sandstone models, using oil. water, and gas. The model floods were scaled to reprotlrrce field performance under gas arid water five-spot injection. X-ray shadowgraphs permitted observation of the gross fluid movement within the models. A method was developed for applying the mobility ratio concept to water flooding and dispersed gas drives in a five-spot well pattern. The area1 sweep efficiency. tit breakthrough for dispersed gas drives is much higher than previorsly expected, Iying in the range of 50 to 100 per cent. A method is presented for predictitig the water-oil ratio performance of five-spot pattern water flood., in uniform sands. This method is verified experimentally for the cotidition of 120 free gas initially present and for va1ues of gas saturation normally encountered in fields following depletion operations. Prodrrction perfort?zut~cc for pattern gas injection is also predictable by this method. INTRODUCTION In field pattern hater flooding or dispersed gas injection operations, the displacing fluid (water or gas) is injected and oil is produced through wells which are, area-wise. small openings in a large container or rescrwir of oil. As a result, not all of the area between the injection and producing wells is necessarily contacted by the injected fluid by the time it first reaches the producing wells. The question arises in predicting oil recovery. as to what traction of the pattern area involved is contacted by either the injected water or gas due to the relative position of the injection and producing wells. This is the areal sweep efficiency. It is also desirable to know how well arrangement affects the oil production performance. A solution to this problem has been attempted by many means. Mathematical analysis¹,²,³, and electrolytic models', have been used to establish a breakthrough areal sweep efficiency of 73 per cent for a five-spot pattern in which the ability of the oil to flow ahead of the invading fluid is equal to the ability of the invading fluid to flow in the invaded zone. All of these studies simulate only one of many field conditions. Improved studies of areal sweep efficiency at breakthrough were made using the fluid mapper5, poten-tiometric models" and X-ray shadowgraph techniques. In these it was possible to study the effect of variations in mobility of the injected and displaced fluids, and so to cover a wide range of field conditions. The limitation of these studies is that, with these models, it was not possible to simulate the saturation gradient behind the flood front when oil is displaced by gas or water. In the most recent published technical paperS on the subject, a method was presented for predicting the oil recovery performance after breakthrough in a five-spot pattern water flood. The method involved correlations which were obtained experimentally using miscible fluids. One limitation of this work was that a saturation gradient, usually found in immiscible fluid displacement, was absent in these studies. Also the laboratory studies did not cover the situation of a water flood following oil recovery by depletion drive. as is the situation in most field water floods. The tests reported in this paper were made using oil. water, and gas, thus eliminating the simplifications of former studies. Also reported are laboratory studies on

Jan 1, 1956

By R. B. Schluter, M. M. Fine

Development of a process for winning copper from pelletized chalcocite concentrate is underway at the Bureau of Mines, Twin Cities Metallurgy Research Center. The new route from concentrate to metal by which the Bureau seeks to eliminate matte smelting and converting includes a two-stage fluid bed treatment. In the first stage, pelletized concentrate containing 32%Cu and 7% S is first desulfurized to less than 1.0% S in an oxidizing atmosphere. In the second stage, the calcine is metallized by reduction with hydrogen. Thereafter, the reduced product plus 10% CaO is routed to a smelting furnace which separates metallic copper from the gangue. Recovery and Cu content at this point are in the 97-98% range. This product must be refined to remove sulfur and iron so the metal is suitable for making wirebar copper. An important feature of the process is fine concentrate pelletization prior to fluid-bed treatment. This permits a shorter reaction time, a decrease in dusting and easier subsequent processing. In a broad sense, sulfide copper pyrometallurgy is a batch sequence in three separate vessels, i.e., a reverberatory furnace to yield matte copper, a converter to produce blister copper and another reverberatory furnace to produce fire-refined copper. Matte-smelting has remained relatively unchanged since it became a universal practice some 50 to 60 years ago. It is now serving a wide range of smelter feed materials, but many concentrates are not immediately amenable to the process. There are abundant copper resources which lack sufficient sulfur and other elements lo sustain the full chemistry involved in matte-smelting. This necessitates adding sulfur to make the product fit the process, and usually none of the sulfur is recovered. From the standpoint of pollution alone, the development of a smelting technique for low-sulfur concentrates not requiring the addition of sulfur would be a significant gain.

Jan 1, 1970

W. VAN DER GRACHT, Tulsa, Okla. (written discussion.*).-I fully agree with Mr. Daly's observation that there is such a coincidence between petroleum deposits and geosynclines as to suggest them to be "closely allied phenomena." However, I accept no "identity of cause." To me the explanation is a simple one. Geosynclinal deposition is the first phase in the formation of a mountain, chain, and petroliferous deposits are indeed closely allied to zones of, mountain folding. In fact, petroleum is a typical occurrence in those beds, which represent the flysch facies, to use the Swiss expression. The uplifting of a great mountain chain is a very slow process; it gradually sets ill as a slow geo-anticlinal upheaval within a zone off former geo-

Jan 1, 1918