Search Documents

By W. P. Lass

Discussion of the paper of W. P. LASS, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 103, July, 1915, pp. 1443 to 1447. ROBERT M. KEENEY, Somersville, Conn. (communication to the Secretary *).-There is not only a possibility of improvement in present methods of treatment of the byproducts of refining in the cyanide plant by the use of the electric furnace, but also in melting and refining of gold precipitate. This interesting paper by Mr. Lass shows an electric furnace in successful operation in a large plant for the treatment of by-products. Electric melting of cyanide precipitate is a cheaper form of treatment in many cases than any of the combustion methods now used because of the high cost of oil, coke or coal in many camps, while on the other hand electric power may be had cheaply, especially in a place where there is possibility of development of high-head hydro-electric plants for power purposes. Also, if the oil-fired tilting furnace is used for direct melting of the precipitate, as is the case at many small mills, a great saving in cost is made by the use of the electric furnace because of the high crucible cost in melting with the tilting furnace. A study of this paper indicates the cost of the operation approximately. Consider all the fluxes to be turned in as byproducts and coke at $18 per ton.

Jan 12, 1915

By W. G. Pfann

A simple method of obtaining multistage batch separations by crystallization was described recently. Known as zone-refining, it comprises passing short molten zones through a long solid charge. This technique can now be used on a continuous basis by means of the zone-void method described in this paper. Feed enters, at an intermediate point, a column down which molten zones travel, and waste and product leave at the ends. Materials move in the column through the agency of voids, which are introduced at the ends and travel toward the feed inlet. The voids and molten zones are moved by external heaters in a simple manner, and the principle of reflux is utilized. ANEW method of obtaining multistage separations by crystallization was described recently.' Named zone-refinina.,-, the method comwrises slowly passing a series of molten zones through a long solid charge. Solute becomes concentrated at one or the other end of the charge, depending on whether it raises or lowers the freezing point of the solvent. The separation increases with the number, P, of zone-passes, approaching a limit as P approaches infinity. Zone-refining has been highly effective in purifying germanium and other substances.2,3 and new applications are steadily increasing. Zone-refining is a batch method and as such it has certain limitations inherent in batch operation. If it could be made continuous, its scope and utility would be greatly broadened. This end has been achieved by the zone-void method described in this paper. In the zone-void method feed is introduced continuously at an intermediate point in a column down which molten zones travel, while impure waste and purified product leave at the ends. Both the flows of feed, waste and product, and also the travels of the zones, are actuated by external moving heaters in a simple manner; and the system utilizes the principle of reflux. The method provides, in the field of crystallization, the counterpart of the continuous fractiona-tion column in the field of distillation. The following will be discussed: apparatus and mode of operation, fundamental nature of the separation, design theory, and practical considerations. The method will be described in terms of a binary solute-solvent system in which the solute is an impurity to be removed and the solvent is the desired product. The distribution coefficient, k, defined as the ratio of solute concentration in the solid freezing out of a molten zone to that in the liquid in the zone, is assumed to be constant and less than one. The process is equally effective for k's greater than one and for ternary or higher order systems. Method and Apparatus The essential features of a continuous zone-refining process are represented in highly generalized form in Fig. 1. A series of molten zones, produced by moving heaters, travels slowly down the column or charge (to the left in Fig. 1). If there were no flows of feed, waste, or product, the process would simply be batch zone-refining, the action of the molten zones being to sweep solute down the column, solvent up the column. For the process to be con- tinuous, with stripping and enriching sections in the column, feed must enter, and waste and product must leave, as indicated. The zone-void process accomplishes both objectives, namely, the indicated movements of zones and the indicated flows of material. Zones are moved by moving heaters, just as in batch zone-refining. Materials are made to flow by creating voids at the waste and product exits and causing these voids to move to the feed inlet. Since there must be a net flow of material from the feed inlet to each of the outlets, the indicated movements of voids are in the desired directions, because movement of a void in a given direction corresponds to flow of material in an opposite direction. In order to produce the desired movements of voids, the column is folded into two vertical sections having the feed inlet in common at their upper ends. Voids are displaced upward by the liquids in the molten zones and their travel is actuated by the motions of the zones. Voids travel with the zones in the enriching section and move continuously. Voids travel opposite to the zones in the stripping section and move intermittently. Creation and travel of voids will now be examined in detail. The enriching section of a column in operation, with its void generator, is shown in Fig. 2. The column section is a vertical tube around which a series of closely fitting, regularly spaced heaters travel slowly upward. Each heater produces a molten region, the temperatures of the heaters and the cooling between heaters being controlled so as to maintain the molten zones approximately constant in size. A void is normally present atop the molten zone in each heater. As the heater rises, it continuously melts solid above it, which drips through the void into the molten zone and continuously freezes out solid below it, of concentration k times that of the liquid in the zone. When a molten zone and void reach the feed inlet, which is kept molten, the void is displaced by an equal volume of feed liquid. Generation of voids of controlled size in the enriching section is shown in Fig. 3. The void generator is a tube of small cross-section, provided with lateral heat-conducting fins which sense the position of the heater. Liquid can escape only when the entire outlet tube is within the heater. If any part of the outlet tube is outside the heater, liquid cannot escape,

Jan 1, 1956

By W. S. Row

This mine is operated at 4000 to 4500 tons daily through a single shaft, with one rock hoist and one senice hoist. Latest shaft construction is concrete with wooden dividers. Economics of drifters and air-leg drills are compared, as well as costs of shrinkage and sub-level stoping. Economy of large haulage equipment and underground crushing is shown. THE property of Kerr-Addison Gold Mines is located in the Larder Lake district of Ontario about 3 miles from the Quebec boundary on the highway between Kirkland Lake and Noranda. It is roughly 320 miles due north of Toronto and 365 miles north of Buffalo, N. Y. The property was staked in 1906 and after several development efforts finally came into continuous production at 500 tons per day in 1937. In 1939 the daily tonnage -was increased to 1200 and in 1941 to 2100 tons. At the end of the war, because of the shortage of labor, tonnage was down to 1100 tons per day, rising to 2200 in February 1947. A further plant expansion inaugurated in 1946 was completed by December 1948, bringing the capacity of the mine and mill to a production rate of 4000 tons per day. Current production, with 880 men employed, is 4400 tons per day. Changes in mining methods and equipment, required by the recently completed expansion program, have yielded interesting comparative results, some of which are described in this paper. Hoisting of ore and waste from the mine, as well as all service facilities for handling men and supplies underground, are provided for in a single vertical five-compartment shaft. Ore and waste are hoisted in 12½-ton skips in balance by a 14-ft diam hoist with drums 115 in. wide, grooved for 2?-in. wire ropes. This hoist, with a total rope pull of 85,000 lb, was designed to operate at a speed of 2600 ft per min to a depth of 4000 ft, hoisting 15 tons of ore in each skip. It is amplidyne-controlled and powered with dual drive dc motors of 2250-hp each, through flexible couplings to two pinion shafts, one on each side of the main gear. Each motor has a peak load rating of 4500-hp at point of greatest duty. Direct current power to the hoist motors is supplied from a motor generator set consisting of a 5000-hp synchronous motor driving two 1750-kw dc generators. The loading pockets used so far are at depths of 1500 and 2725 ft respectively. Consequently the present hoisting speed is 2000 ft per min and the skips capacity only 12½ tons. Now that the shaft has been deepened the new pockets at 3934 ft will be increasingly used so that the speed and the skip size will be increased up to original specifications as required. Some difficulty in meeting the required hoisting cycle is expected because of the shape of the skips. As now in use the cross-sectional dimensions of the inside of the skip are 4 ft 6 in. x 3 ft 8 in. To hold 121/2 tons, therefore, they are 14 ft 10 in. deep. Since the skips are the conventional overturning or Kim-berley type, considerable hoisting time is lost in retardation in entering the headframe dump and in acceleration when leaving. It is expected that to obtain the specified tonnage from this hoist when the skip size is increased to 15 tons it may be necessary to resort to bottom dump skips. This type of skip could reduce considerably the present excessive acceleration and retardation times. Analyses of the skip-hoisting operation are made monthly, and every effort is made to reduce controllable delays. For a nine-month period in 1951 such an analysis shows that the hoist was in operation 92.5 pct of the available time, which was allotted as shown in Table I. Overall hoisting costs, cage and skip, for the year 1951, averaged $0.168 per ton of ore milled. The mine is serviced entirely by means of a single cage, capacity 35 men or 15,700 lb, operating in con-

Jan 1, 1954

THERE are two general types of scientific approach to a problem. One approach, which is the more widely known, involves an analysis of the situation at the beginning of the experiment; this is followed by an analysis of the situation at each instant of time during the experiment and leads to a-detailed description of the prevailing conditions at the end of the experiment. Suppose, for example, we wish to predict the final rest position on a billiard table of a ball moving initially in a certain known direction with a known speed. The obvious approach is to estimate or measure off its course by consideration of angles of rebound, taking account of the "English" or spin if necessary and finally estimating from experience (or calculating from coefficients of friction) the slowing down occasioned by friction, thus establishing the point of the course at which the ball may be expected to stop. Any interference with the calculated course occasioned by collision with an unanticipated object would obviously cause us to revise drastically our estimate of the rest position. This general method of approach characterized by detailed description of how one situation developed from another seems intuitively appealing and is the most widely known method. There is no doubt that it gives very satisfying results when it can be used. There is a second general method of approach. In this method, the final state of a system is predicted from knowledge of general broad principles and their application, considering only the restrictions imposed upon the system. It is unnecessary to follow the course in detail; intermediate steps are not even considered. For example, if the billiard table mentioned in the first paragraph were tilted to one corner, one could predict that the final resting place of the ball would be in that corner; this prediction can be made independent of any particular course the ball may follow. This second general method of attacking problems is the one used in thermodynamics. There its use is so outstand-

Jan 1, 1951

By R. T. Webber, B. B. Owen

THE vapor phase deposition of molybdenum and tungsten from the hexacarbonyls has been thoroughly investigated by Lander and Germer1 and shown to yield well-bonded coatings on a variety of hot metallic surfaces. They also demonstrated that chromium coatings2.3 could be similarly deposited, but did not investigate this metal extensively. Recently,4 conditions have been described by which this compound can be prepared in quantities sufficient for laboratory scale plating experiments, and it is the purpose of the present communication to outline the results of preliminary experiments upon the plating of chromium from its carbonyl. APPARATUS AND TECHNIQUE The apparatus used in these experiments is shown in Fig I. At one end, connected by a short length of rubber tubing, is a Cenco Hypervac 20 pumping continuously. At the opposite end is a needle valve which allows a small stream of purified hydrogen to flow through the apparatus. Connected in series are a trap T1, maintained at the temperature of dry ice and acetone, the plating chamber, and two traps T2 and T3 containing crystals of the carbonyl. T2 is kept in a constant temperature bath (not shown), while T3 is at room temperature. Stopcock S6 allows the hydrogen flow to by-pass the carbonyl traps. A McLeod gauge is connected so that it can measure the pressure at the pump through Ss, or the pressure at the plating chamber through S9 and S6. The standard (12 liter) volume connected by S5 is used to determine the volume included by S4, S6, Se, S10, the needle valve and the McLeod gauge. Knowledge of this volume allows calibration of the flow of hydrogen. The apparatus* is built entirely of pyrex, except for the needle valve, the rubber connection to the Hypervac, and the cover of the plating chamber. The plating chamber is water-jacketed, with a large brass top allowing insertion of the specimen to be plated. Set into the brass top is a ground glass stopper through which thermocouple leads are sealed. The thermocouple wires (pure Pt, and 87 pct Pt-13 pct Rh) serve the double purpose of measuring the specimen temperature and suspending it in the chamber. Surrounding the chamber is the coil of an induction heater, H. The apparatus is designed to allow variation of the following conditions: I, the specimen temperature, from room temperature to about 1000°C, 2, the carbonyl vapor pressure, from 40 to 220 microns, and 3, the hydrogen flow. In several runs, 0.8 to 1.8 pct of hydrogen sulfide was introduced through a needle valve that replaced S4. The vapor pressure of the carbonyl is

Jan 1, 1948

By R. T. Webber, R. B. Owen

The vapor phase deposition of molybdenum and tungsten from the hexacar-bonyls has been thoroughly investigated by Lander and Germerl, and shown to yield well-bonded coatings on a variety of hot metallic surfaces. They also demonstrated that chromium coatings2'3 could be similarly deposited, but did not investigate this metal extensively. Recently, conditions have been described by which this compound can be prepared in quantities sufficient for laboratory scale plating experiments, and it is the purpose of the present communication to outline the results of preliminary experiments upon the plating of chromium from its carbonyl. Apparatus and Technique The apparatus used in these experiments is shown in Fig I. At one end, connected by a short length of rubber tubing, is a Cenco Hypervac 20 pumping continuously. At the opposite end is a needle valve which allows a small stream of purified hydrogen to flow through the apparatus. Connected in series are a trap T1, maintained at the temperature of dry ice and acetone, the plating chamber, and two traps T² and T3 containing crystals of the carbonyl. T² is kept in a constant temperature bath (not shown), while T³ is at room temperature. Stopcock S6 allows the hydrogen flow to by-pass the carbonyl traps. A McLeod gauge is connected so that it can measure the pressure at the pump through Se, or the pressure at the plating chamber through S9 and S6. The standard (12 liter) volume connected by Sb is used to determine the volume included by S4, S6, SB, Slot the needle valve and the McLeod gauge. Knowledge of this volume allows calibration of the flow of hydrogen. The apparatus* is built entirely of pyrex, except for the needle valve, the rubber connection to the Hypervac, and the cover of the plating chamber. The plating chamber is water-jacketed, with a large brass top allowing insertion of the specimen to be plated. Set into the brass top is a ground glass stopper through which thermocouple leads are sealed. The thermocouple wires (pure Pt, and 87 pct Pt-13 pct Rh) serve the double purpose of measuring the specimen temperature and suspending it in the chamber. Surrounding the chamber is the coil of an induction heater, H. The apparatus is designed to allow variation of the following conditions: (I) the specimen temperature, from room temperature to about 1000°C, (2) the carbonyl vapor pressure, from 40 to 220 microns, and (3) the hydrogen flow. In several runs, 0.8 to 1.8 PCt of hydrogen sulfide was introuced through a needle valve that replaced S4. The vapor pressure of the carbonyl is

Jan 1, 1949

By Dr. O’Neil Thomas J., Donald W. Gentry

"Who is the man who views the mines and promptly turns them down? Who is the one that thinks this is the short cut to renown? Who is it gives the bum advice to the innocent financier? The knowledge-feigning, theory- straining mining engineer." -Anonymous INTRODUCTION Taxes levied against mining properties and operations are a critical cost in the economic evaluation of mining investments. Indeed, taxes represent a substantial cost of doing business in the minerals industry and often have a significant impact on corporate investment decisions. A good example was the postponement of mineral development in the state of Wisconsin, primarily because of what was perceived to be excessive taxes imposed by that state. In many respects mining investments are no different from other industrial investments. Astute taxing authorities should recognize that geologic endowment is a necessary but clearly not a sufficient condition for mineral investments. The fact that a mineral deposit exists does not necessarily mean that it will ultimately be developed-a point that many taxing authorities fail to recognize. While it is true that ore deposits are not mobile in the sense that they cannot be physically moved to a district having more favorable taxes, corporate investment capital certainly is mobile and flows to ventures which maximize wealth to the firm. In short, higher taxes reduce project yields and tend to drive investment capital elsewhere. The appropriate type and level of taxation imposed upon the mining industry continues to be a very controversial and emotion-charged topic. Mining activities have been taxed at various levels over the years due to widely differing taxation philosophies. Location has also influenced taxation policies, as evidenced by the diversity of tax laws and assessment procedures applied to mineral deposits by the various states. Indeed, mineral taxation varies from state to state, from county to county, and from one mineral commodity to another. Whether or not a given tax is appropriate for a specific mineral deposit, or even an industry, is a difficult problem to assess. First, the type or kind of tax which should be imposed must be considered. Second, it is most important to define a fair and unambiguous base against which to levy the tax. Finally, one must consider the tax rate to be applied to this base. It is the combination of these two components

Jan 1, 1984

By J. H. Scaff, W. G. Pfann

The effects of impurities on the electrical properties of silicon are discussed in a companion paper by Messrs. Scaff, Theuerer, and Schumacher.' It was shown that an ingot of silicon which contained boron and phosphorus in certain concentrations consisted partly of p-silicon and partly of n-silicon2 and that the common boundary between these regions was the source of a photo-voltage. These features were ascribed to the segregation of boron and phosphorus during solidification of the ingot. Because of different rates of segregation the first portion of the ingot to freeze contained a molar excess of boron over phosphorus and hence was p-silicon. The last-solidified region contained a molar excess of phosphorus and was n-silicon. This paper is concerned with the microscopic examination of such ingots. The microstructures are rather unusual in certain respects and their study has helped to show how the segregation of minor elements modifies the electrical properties of silicon. The microstructures of ingots prepared from two lots of silicon, designated 1 and 2, will be described. These lots were obtained from the Electro Metallurgical Co. Both contain 99.8+ pct silicon, but they differ in impurity analysis. For each lot will be shown the microstruc-ture of a slowly cooled ingot, for which the time of solidification is 6 min., and that of a rapidly cooled ingot, for which the time of solidification is 2 min. The ingots were prepared from 45 g charges of silicon. When an alloy freezes a cored structure is generally produced because of insufficient diffusion to remove concentration differences established during freezing. As a result of coring the first portion of a crystal to freeze is usually poorer in solute than equilibrium requires, while the last material to solidify is richer. In a columnar grain, growth is principally unidirectional and coring can produce a concentration gradient along the entire grain. By carrying the picture of the coring process from a single grain to an entire ingot in which columnar grains are aligned more or less radially, one can easily see that a composition gradient could be established between the outside and center of the ingot. This, to a considerable extent, occurs during the solidification of a slowly cooled ingot of silicon. Slowly Cooled Ingot In slowly cooled ingots of both lots of silicon, columnar grains which are approximately radial in direction and longest at the top of the ingot enclose a region in which the shapes and align- ment of the grains are considerably less regular. The central region is last to solidify and contains cavities and inclusions. The sketch of Fig 1 illustrates some of these features, as well as others which will be described below. If a polished section of an ingot is etched in a mixture of 2 parts of 20 pct HF and 98 parts of HNO3 the p-n barrier becomes visible. The overall shape of the barrier in a slowly-cooled ingot is roughly oval, as may be seen in Fig 1. The proportion of n-silicon, that is, the region enclosed by the barrier, is considerably greater in ingots of lot 1 than in those of lot 2. A sample about 34 x 1/8 X 1/8 in. was cut from a slowly cooled ingot of lot 1 with its long direction extending from the top of the ingot to the porous region. Thus its upper half was psilicon, its lower half n-silicon. A longitudinal face was polished and etched in the acid mixture. The areas of interest are identified in Fig 2. A band of parallel markings extends across the sample in the columnar region. These striae are roughly parallel to the upper surface of the ingot and cross grain boundaries with only slight deviations. They are quite distinct in the n-silicon,

Jan 1, 1950

By H. C. Johnson, J. K. Elliott

One of the primary requirements for successful operation of an enriched gas-drive project is to control the composition of injection gas. This can become a serious and difficult problem, particularly in cases where the enrichment material is being furnished from a number of field -produced gas streams. It is possible to effect control of the injection gas composition through frequent or continuous sampling; however, this can be extremely costly and, in many cases, impractical due to laboratory requirements of time. Another alternative would be to provide a calculation technique which would be flexible and sufficiently accurate to predict composition of the liquid and gas streams of interest at any point in the system. The purpose of this paper is to discuss a technique that was used successfully on an operating enriched gas-drive project for developing information which could be used for controlling composition of the injected gas. FIELD OPERATIONS The particular field (hereafter called Example field) in the example operation being discussed is composed of four oil reservoirs (A. B, C and E) and one gas condensate reservoir (D). Casinghead gas from the oil reservoirs and gas from the gas condensate reservoir are gathered through a field gathering system as shown in Fig. I for injection into Reservoir C. The gas mixture which is recovered from the five reservoirs for injection purposes is composed of gases liberated in 19 individual separators, each operating at a separate temperature and pressure. PROPOSED CALCULATION TECHNIQUE It is well known that vapor-liquid equilibrium calculations in general use throughout the petroleum industry can be used to predict reliably the phase behavior of hydrocarbon mixtures, particularly at pressures less than 1,000 psig. It is then a simple matter to account for the material on a ComPonent basis by m''ing flash and material balance calculations at each separation point in a hydrocarbon system. Accordingly, it was proposed to use vapor-liquid equilibrium and material balance cal- culations with a medium-sized electronic digital computer as a basis for developing a control procedure for use in controlling injection gas composition in the enriched gas-drive project. Although the approach is a simple one, the numerous vapor-liquid equilibrium calculations involved make the problem laborious; in this particular case, it would have been impractical to make sutficiently complete analysis without the aid of digital computing equipment. SAMPLING AND VERIFICATION OF CALCULATION PROCEDURE To obtain representative gas and liquid stream samples and to provide a quantitative measure of overall system Performance for comDarative purpLses, a thorough test of the field and plant system was conducted in the summer of 1957. Oil production at each battery was sta-

By L. Bombardieri, H. F. Mills

Iron King mine, producing gold-silver-lead-zinc-ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pat tern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length, with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth, the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 5 ½ -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material.

Jul 1, 1956

By C. Wagner

When an alloy solidifies and the composition of the solid differs from the composition of the liquid, atoms of the alloying elements rejected at the solid-liquid interface have to diffuse toward the bulk liquid. Diffusion may be supported by convection. Theoretical calculations have been made for a liquid without convection, for a liquid involving natural convection, and for solidification of a liquid alloy at the surface of a rotating disk as an example of forced convection. WHEN an alloy solidifies, the equilibrium composition of the originating solid phase differs in general from the composition of the liquid phase. Thus, segregation may take place, i.e., the composition of the solid phase formed at different times differs from the bulk composition. The degree of segregation depends on several factors such as the partition ratio of the alloying elements between the liquid and the solid phase, the rate of solidification, and convection. To clarify, a theoretical analysis has been worked out. The following presuppositions are made: 1—Calculations are confined to the solidification of binary alloys in which the concentration of component A (solvent) is much greater than that of component B (solute). 2—The equilibrium concentration of the alloying element B is assumed to be lower in the solid phase than in the coexisting liquid phase. 3—At the solid-liquid interface, partition equilibrium is assumed. 4—The dependence of the partition ratio of the solute between the liquid and the solid phase on concentration and temperature is disregarded since only small concentrations of the solute are considered. 5—The concentration of the alloying element B in the solid phase is supposed to be lower than the saturation concentration for the formation of a second solid phase. 6—diffusion in the solid phase is disregarded, since diffusion rates in the solid state are comparatively low. When the partition ratio of the solute between the liquid and the solid phase is greater than unity, a part of the solute is rejected at the solid-liquid inter- face and has to diffuse toward the bulk liquid. Thus there is necessarily a concentration difference in the liquid between the solid-liquid interface and the bulk liquid as has been pointed out by Hayes and Chipman,' Rutter and Chalmers,' Tiller, Jackson, Rutter, and Chalmers, and others (see Fig. 1). In view of the concentration gradient in the liquid phase, the ratio of the concentration of the solute in the solid phase to that in the bulk liquid differs from the equilibrium ratio, although at the solid-liquid interface, partition equilibrium is assumed. Under certain limiting conditions, the solid may even have virtually the composition of the bulk liquid as is shown below. General Equations Let u be the linear crystallization velocity in cm per sec, D the diffusion coefficient of component B in the liquid phase in cm2 sec-', c',, and c", the concentrations of component B in the liquid and the solid phase, respectively, in mol per cm", and s the distance from the solid-liquid interface toward the bulk liquid at a given time t. The partition ratio is assumed to be equal to a partition constant K. Thus. The difference in the specific volume between the liquid and the solid phase may be disregarded. In view of the discontinuity of the concentration of the solute at the interface according to Eq. 1, u(c', — c",), , , = tic', (S = 0)(1 — K) gram-atoms B per unit area per unit time are rejected at the interface and have to diffuse toward the bulk liquid. From Fick's first law it follows that uc',,(s = 0) (1 ~K) == - D(dc',,/?>s). _-„. [2] The concentration profile in the liquid near the interface depends on the interplay of diffusion and convection as is discussed in the following sections. A schematic concentration profile is shown in Fig. 1. The "effective thickness of the diffusion boundary

Jan 1, 1955

By R. S. Wagner, R. G. Treuting, W. C. Ellis

Use of the Weisseizbevg goniometer for the study of the morphology of whisker crystals and transfer of the results to a stereograplzic projection are described. While in almost all instances a complete and rapid solution is obtained with a purely gaphical treatment, an absolute analytical treatment applicable to difficult cases is given. Examples are given for determination of growth direction and external features of a crystal, for detection of 'twintzittg, and for establislting the orientation relntionships in a kinked whisker crystal. We give here a method for the use of the Weissen-berg goniometerl" in the study of orientation relationships in "whisker" (micro) crystals3-8 and direct transference of the data to the stereographic projection. The operations are straightforward and require no involved calculations: in almost all cases solely graphical treatment is adequate. In a few complex instances, a more exact analytic method may be required. In the method, not only are equatorial reflections of an oscillation photograph used, but also those on higher layer lines, or those not occurring on a recognized layer line. Such reflections off the zero level are often essentialy to detect the presence of twinning. The method is particularly suitable for examination of whisker crystals since the axial or growth direction is almost always one of high symmetry, permitting a more restricted oscillation range to obtain the necessary reflections and an accordingly shorter exposure time. The method is also applicable when there is no lattice-related external symmetry, and is as well able to identify external crystal surfaces, when such exist, with the aid of an optical beam. Thus growth direction, identification of lateral faces, twinning, and orientation relationships in a kinked crystal can be established. A test for the Eshelby twist6-8 can readily be made. The method can be used for orientation, for structure analysis, and as an aid in the identification of an unknown crystal. Moving-film techniques have previously been employed variously for crystal-orientation studies.1,2,9-13 In particular, use of the Weissenberg method for orientation determination has been reported by Wooster and wooster.14 While their method derives the same data as here described, it differs in depending on the tracing of constant p streaks, a less than dependable phenomenon with small specimens, a few microns or less in cross section. The Laue method can and has been used for orientation studies of microcrystals,15 e.g., 2 p in cross section, but requires the extreme intensity and concentration from a microfocus tube to obtain reasonable exposure time. PRINCIPLES OF THE PRESENT METHOD Consider a crystal of random orientation with respect to the oscillation axis in a Weissenberg goniometer. Its diffraction pattern need not necessarily result in recognizable layer lines. In Fig. 1, a stereo-graphic projection of the reference sphere is given with the equatorial plane XZ normal to the oscillation axis Y, and the X-ray beam directed from X towards 2. The great circle ZZ is then normal to the beam, and the axes are right-handed. Thus the reflected X-ray beam lies at the intersection R of small circle ARB of radius 28 from 2, and of small circle RE of radius a from the rotation axis Y. a is the conventional semiapex angle of a cone of diffracted rays from the atoms aligned in the direction

Jan 1, 1967

By Gilbert Francklyn

The requirements of coals for the manufacture of coal gas, water gas and producer gas will be considered sparately and a short description of each gasmaking process will be given. In this report the term "gas coal" is confined to coals suitable for the manufacture of city gas in horizontal, inclined or vertical retorts. The report does not refer to coke-oven practice.' Briefly, the process of manufacture consists of distilling the coal at high temperature in an externally heated retort out of contact with the air. The products of distillation, consisting of gas, tar, ammonia, etc. are collected and purified. The residue consists of coke, which is removed from the retort at the end of the carbonizing period. To supply the heat required in the process, a portion of the coke produced is converted into producer gas, which is burned under the retort settings. Qualities of Gas Coals The chief qualities that coal must possess in order to be classified as a gas coal are as follows: 1. Gas Yield.—The coal must be capable of yielding gas in sufficient volume and of a satisfactory quality. The yield depends considerably upon the temperature of distillation; a higher temperature will give a larger yield of gas, but the qualit,y of gas (now measured by the British thermal units per cubic foot) will be lower, while a lower carbonizing temperature will give less gas of higher heating value. The true measure of the yield is the number of British thermal units produced in the gas from a given quantity of coal. This number is obtained by multiplying the cubic feet of gas from 1 lb. of coal by the British thermal units per cubic foot of gas; it is called B.t.u. feet per pound. It is found that the

Jan 1, 1930

FREQUENTLY the careful engineer puts the word porphyry in quotation marks or precedes it with "so-called," when he writes of the Porphyry Copper mines. This is done by way of serving notice that he is aware that the term is not a precise one, though no one who is informed on the subject would in any event misinterpret it. The name originated from the fact that the rock containing the copper at Utah Copper, Morenci, Nevada Consolidated, and Braden-the first four to be developed-was in each instance known as porphyry. The term was convenient; and when Ray, Miami, and inspiration came along they fell into the Porphyry category even though the ore consisted essentially of a rock called schist instead of porphyry. The word is not inclusive enough; nor as a matter of fact is it sufficiently exclusive. Numerous copper deposits occur in porphyry rocks that are not Porphyry Coppers, paradoxical as it may seem. Desiring to be more accurate and at the same time to use a word that is in some degree descriptive, various engineers have adopted the expression "disseminated copper deposits." This alludes to the characteristic scattering of grains or specks of copper minerals more or less uniformly throughout the mass of the rock. Yet here again the implication is not entirely accurate, for the following reason: in some of the ores, the proportion of copper minerals "peppered" in the rock is small, compared with that which coats the walls of cracks and minute fissures; and that which is found as veinlets along planes of fracture. Many geologists have extended their interpretation of the term disseminated to include both types of mineral occurrence. One of the most striking features of the Porphyry ores is the intense shattering and fracturing that the rock underwent at some period or periods prior to the deposition of the copper

Jan 1, 1933

By Oliver C. Ralston, Foster Fraas

VIRTUALLY all commercial use of electrostatic separation has employed separators depending on differences of conductance of the broken, solid mixtures treated by them. The two main types of conductance separators have been: (1) Those in which the separating field is as near a static field between two charged electrodes as it is possible to maintain in the face of the usual leakage that takes place between electrodes with some 5 to 50 kv tension between them and spacing of l/z to 3 in.; (2) those in which a convective discharge of corona or spray type, but not a spark discharge, takes place between the carrier electrode and a charged electrode facing it, which is of very restricted area, such as a row of needle points or a small diameter wire parallel to the face of the carrier electrode. The present paper deals with this latter type. The principle is usable in separators where the carrier electrode, usually grounded, has the shape of a roller, a conveyor belt, a vibrating table, a sloping chute, or a nearly vertical plate. The innovation studied by us has been the use of the convective field for charging material on the carrier electrode and succeeded by a field between the carrier electrode and an electrode made of a true dielectric which cannot take on a charge by conduction but is charged by being in the radius of the corona discharge. The acquired charge is of the same sign as that of the corona but is not dischargable by contact with a good conductor. However, high-tension charge tends to leak off because of the ionization of the ambient air. The field between this electrode and the carrier electrode is as near static as it is possible to obtain. There are some differences in behavior of this electrode and that of the gas tube electrode used by Sutton, as will be discussed below. Both electrodes cause increased adhesion of nonconductive particles to the carrier roll. The particles are pinned there because they are convectively charged on their outer surfaces facing the corona electrode. The electrodes also cause increased rate of release of conductive particles tending to be pinned by corona charging but conveying the charge to the grounded carrier roll almost as rapidly as it is received by the particles.

Jan 10, 1950

Discussion of the paper of E. J. Hall and C. W. Drury, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 78, June, 1913, pp. 1059 to 1066. A. M. SMOOT,* New York, N. Y. (communication to the Secretary +) :-The nails method is given in many text books on assaying as a standard method for gold or for gold and silver in ores. It appears to be taught in the laboratories of technical and scientific schools as a standard method, and to some extent it is used by assayers in actual practice, although the class of ores to which it may be applied is limited to those free from reducible metallic compounds, the metals of which would enter the lead button. The experiments of Messrs. Hall and Drury show the inaccuracy of this rnethod for silver, in heavy sulphides, but not so clearly the short-comings with regard to gold. It seems certain that low silver is caused by the solubility of silver in iron-alkali sulphide as compared with its solubility in molten lead; that is, silver is distributed between iron-alkali sulphide and metal in the charge in proportion to solubility at the particular temperature of the fusion. Lead is a fixed quantity in these assay charges, but iron-alkali sulphide increases with increased sulphur, so the more sulphur in the charge, the lower the silver results.

Jan 11, 1913

By C. Pin, J. Bruce Wagner

In order to demonstrate the role of defect chemistry in the solid state to a process-metallurgy reaction, laboratory experiments were carried aut to remove copper from liquid lead using lead sulfide which had been doped to provide definite concentrations of cation vacancies. The removal of copper decreases in the order: bismuth- or antimony-doped PbS, undoped PbS or tin-doped PbS, and silver-doped PbS. The data are explained using the simple mass -action law and in terms of the exceedingly rapid interstitial diffusion of coppw in PbS to vacant cation sites. Results are in agree-ment with thermodynamic predictions and certain industrial practices that copper may be removed from lead below the limit of its coexistence with pure Cu,S and pure PbS. The role of defects in solids has been exploited in semiconductors and many device applications, in explaining tarnish formation, dissolution rates, and mechanical properties. The application of these principles to many process-metallurgical problems has not received as much attention. It was the purpose of this study to illustrate the role of defect structures of solids in a process-metallurgical application. When lead is refined, the ore, galena (PbS), is reduced by a series of operations to liquid lead (lead bullion) containing impurities such as copper, bismuth, antimony, arsenic, and silver depending on the original composition, the fluxes added, and the particular type of operation, see Fig. 1. In order to produce a pure lead, a series of refining operations are carried out. A typical lead-bullion analysis before drossing is shown in Table I. Copper is removed first as its presence increases the zinc consumption during the desilverizing process. For preliminary copper removal the lead bullion is brought to a temperature of 440°C in a kettle of 60 metric tons capacity. Some tar (or sawdust or resins) is usually added and the kettle is cooled slowly to 400°C while the liquid is stirred. A solid phase, called a dross, floats on top of the liquid and the particles of the solid phase adhere to the tar. This "hot dross" is collected. It contains mostly lead and copper which are partly oxidized and/or sulfurized if the lead bullion contains some sulfur.*

Jan 1, 1963

By Campbell Hunter

PETROLEUM is found in almost every province in Persia. On the northern frontier, along the southern shore of the Caspian Sea, it is found near Anzelli and Shakhtesar and gas at Khoremabad. Oil is also found at Gumush Tepe, northwest of Astrabad, on the southeastern shore of the Caspian Sea. Further inland, to the south of Astrabad, oil is found at Schahkuh-i-balae, also on the margin of the Khorasan desert at Semnan, 115 mi. (35 m.) east of Teheran. Along the western frontier, from northwest to southeast, oil is encountered at Ouschachi, north of Lake Urumieh; in the province of Azerbaijan, at Zohab, Khanikin, and other places in the district of Kormanshah in the province, of Ardelan. Further south, in the province of Luristan, oil is found east of Mendeli and in the Pusht-i-kuh districts. Considerable quantities of oil are also obtained from Schuster, Maidan-i-Naphtun, Ram-Hormuz, Beheban, which are almost on a straight line, running northwest and southeast along the foothills of the Bakhtiari Mountains. At Ahwaz, in the province of Arabistan, oil has been found along another range of hills whose axis also lies in a northwest-southeast direction. In the Fars province, boring for oil has taken place at Daliki, and indications of oil are found at Kheri, Fasa, Darab, and other places. A gas show is also recorded at Kuhi-Sung-Atush in this province, 30 mi. (48 km.) east of Darab. In the south of Persia, oil is encountered on. Qishm Island, also at Ahmedi and other places north of Bunder Abbas. On the southeastern frontier, oil is found on the Sarhad range of hills. Thus, oil indications have been noted over a distance of approximately 1100 mi. along the western and 700 mi. along the northern frontiers of Persia.

Jan 2, 1920

By David Browne

THE literature dealing with the physical constants of nickel is so fragmentary and unrelated, that a synopsis presents unusual difficulties. It is only within the last few years that investigators have understood the importance of placing on record not only the determinations they have made but also the composition, physical treatment, and past history of the material investigated. For this reason much of the earlier literature is valueless. Determinations have been made of the same physical constants on samples differing widely in origin, composition, and treatment, and the results differ widely among themselves. In the first place nickel is almost as flexible a term as steel. Its physical properties are widely influenced by its composition and treatment. It absorbs large quantities of gases and is exceedingly difficult to prepare in a state of chemical purity comparable to gold, silver, or copper. It is vitally affected by thermal and mechanical treatment. Hence in the following pages the recorded literature, where quoted, must be accepted with a certain reserve and used, as far as possible, as a check on later observations, in which these important factors are noted. In every case where new determinations are given, an attempt has been made to record all available information concerning the composition and treatment of the material used so that the data may serve as steppingstones toward a wider knowledge of the properties of the metal. As this synopsis is an attempt by men of metallurgical training to do what should long before have been clone by physicists, it is to be expected

Jan 9, 1919

By R. O. Williams

The concept of biaxial pole figures which completely represent sheel textures is defined and an iterative least-squares solution given. The method has been applied to rolled copper, aluminum, and brass. The results show that the prior ideal textures are reasonably correct but incomplete. The major components in all three cases consist of a continuous range of orienta-tions roughly described as starting from (211) [111] continuing to (110) [112] to (110) [001], the details dif- THIS paper considers the problem of representing rolling textures in the most useful and comprehensible manner possible. A representation called a biaxial pole figure which completely represents such textures fering in all cases. For brass, in particular, the last part of the range is the most important. A minor cube component is established for the copper and aluminurn. The results were also analyzed by means of sets of three axial (inverse) pole figures to give similar, less-detailed results. The method of analysis is outlined. Such a representation is significantly less powerful than the biaxial method, but it has considerable utility in the calculation of anisotropic properties. is defined and an iterative least-squares solution is given. Such textures may be approximated by treating the principal directions as fiber axes to give three axial (inverse) pole figures. This representation is very useful for calculating anisotropic properties. New data for rolled copper, brass, and aluminum are given by both methods. In an axial pole figure the relative frequency or probability of a given physical direction (normally the

Jan 1, 1969