Search Documents

By E. V. Potter, H. C. Lukens

INTRODUCTION IN general, during all electrowinning processes, large volumes of gas are liberated at the cathodes of the electrolytic cells. Most of this gas escapes from the electrolyte, but much of it may be absorbed or entrapped in the metal being plated. In many cases, this is not objectionable, but since it is liberated when the metal is heated, it is a potential source of trouble where the metal has to be heated or melted. Since this gas is principally hydrogen, in escaping from a melt it may cause minor explosions and scattering of the molten metal, while in other cases it has been reported to make the metal rise in the molds when cast. Therefore such metals would be more generally useful if all or most of the gas were removed before they were used. In an earlier investigation' the gas content of electrolytic manganese was determined and methods found for removing most of it without detrimentally affecting the properties of the metal. In this paper results of a similar investigation on electrolytic chromium are presented. APPARATUS The apparatus used in these investigations is essentially the same as that used in the manganese work' and is shown in Fig I. It consists of sample chamber A, vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The pressure in the system is measured by the mercury manometer B. Changes in ' gas volume are measured by volume gauge C which is essentially another mercury manometer in which . the volume of the mercury column is large and can be varied by raising or lowering the well H. In this apparatus the tube had a volume of 100 cc for a 61 cm length. Larger changes in gas volume can be accommodated by auxiliary containers attached to the system at F. The sample is heated by furnace G, the temperature of which is regulated within ± 5°C by an automatic controller. The only change in the apparatus was the sample container which was made smaller because of the chromium metal's containing more gas than the manganese metal and a smaller sample was used. METHOD The measurements were made as follows: The complete system when cold was evacuated and refilled with H2 until all the air was removed. It was then refilled with H2 to the desired pressure, as indicated on manometer B. The temperature was then raised to the desired value and as gas was either liberated from or absorbed by the sample, the height of well H was changed to alter the volume of the system so as to keep the pressure constant. In determining rates of liberation of gas, volume readings were taken at convenient time intervals depending on the rapidity with which the gas was liberated. In determining total volumes, the specimen was held at constant temperature and pressure until

Jan 1, 1948

By Glenn C. Waterman

THE diamond drill is a very important tool in exploration and development testing and its use is increasing. In almost all cases results of diamond drilling are analyzed on the basis of grade and tons. A proper evaluation of core and sludge assays is important if drilling results are to be acceptable as a basis for geologic and engineering appraisal. The relatively wide variation in assay averages as calculated by various well-known combining methods indicates that the engineering choice of a method may affect the outcome of the drilling in terms of ore and waste. The problem of combining assay results from core and sludge samples has been discussed many times in conference and in the literature.'-' Most writers agree that the field of disagreement in methods is large and that the engineer on the job must consider features unique to his drilling, pick one of several combining methods, and depart from the rules when abnormal results come in. All the discussion to date can be summed up by the admission that as yet there is no fairly simple, generally acceptable combining method that is practicable over a wide range of drilling conditions, ground conditions, and ore occurrence. The combining problem is important in evaluating drilling results at Chuquicamata. Recently a reappraisal has been made of recovery variables and their effect on assays, with the result that a new combining method is offered which fits average drilling conditions and is mathematically reasonable. It is simple in application, fundamentally correct, and an improvement over most combining methods. At Chuquicamata diamond drillholes are used to outline the grade and position of blocks of normal and marginal grade oxide, mixed, and sulphide ore. Most holes penetrate all classes of material (and waste), and it is important for mining programs as well as ore reserves to know almost precisely the soluble and insoluble copper content of mineralized ground. At present three classes of ore are mined and treated differently. For an orderly sequence of mining operations which can provide regular daily tonnages of all three ore types and keep grade at certain levels with minimum variation, ore type and its grade must be predicted. Diamond drilling plus geologic mapping and bench sampling are tools for prediction. And drilling data are largely used to calculate grade of material more than a few meters away from bench faces. The orebody at Chuquicamata" is criss-crossed by millions of barren or mineralized weak to fairly strong slips and fault fissures. Mineralization is diverse and encompasses many quartz and oxide or sulphide-bearing copper veins, as well as seams and disseminated grains. Copper occurs in oxide or sulphide minerals or mixtures of these two mineral types. Rock conditions vary from intensely seri-citized (soft and porous) through clay-altered ground to almost fresh granodiorite. The result is an orebody which offers many obstacles to good and consistent core recovery in diamond drilling. Recovery varies considerably in the several alteration zones, the various types of oxide and sulphide ores, and the position and inclination of the drillhole within the complex fracture pattern. As core recovery drops sludge samples must be used with core samples to calculate grade. Many years of drilling at Chuquicamata indicate that in good grade oxide zones and in the sulphide areas core recovery is good and the ground uniformly mineralized. Moderate loss of core, therefore, does not markedly affect grade calculations based on core assays. An early core-sludge combining method used core assays at face value as indicating grade down to 50 pct core recovery, but below this recovery percentage sludge samples were used and weighted according to the standard Longyear chart. This method apparently did not introduce serious errors, but it abruptly used sludge assays with high weighting factors representing 100 pct return irrespective of actual percentage of sludge recovered. Recent drilling activities have been directed toward outlining the marginal ore areas. The non-uniform mineralization and generally poorer core recovery in such ground indicated that a more exact core-sludge combining method was required to equate wide differences between core and sludge assays and recovery. In fringe ore areas at Chuquicamata core recovery averages about 50 pct, from a minimum of 10 to 15 pct to a maximum of 100 pct. Sludge recovery is likewise variable and averages perhaps 80 pct even though holes are cemented as water return falls off. In a homogeneously mineralized area cut by many slips and faults, with hard and soft ribs, loss of core is loss of ground which has a grade similar to that of core recovered, and core assays approximate true grade. In this case sludge samples need not be used. However, it would be unusual to know beforehand that an area is uniformly mineralized, and in fact this condition is probably uncommon. Generally the distribution of valuable minerals in the ground does not exactly compare with their recoverability in core. Thus, in the usual case, loss of core decreases the

Jan 1, 1956

Flaubert, as we know, laid stress on the selection of the right word, le mot juste, the precise epithet, the word that belongs to the thing. A sentence, or even a paragraph, may be spoiled. by the use of a word that is not proper, that does not fit or is foreign to the meaning intended. An Australian mining expert is reported to have said: You have a property of considerable value, and what I saw warrants s good development of very rich cubicular galena, with gossan intermixed. 'Cubicular' means 'belonging to a small bedroom', a 'cubicle' being a sleeping compartment. He meant 'cubic', of course. This is a malapropism, and reminds me of the lady from Chicago that, on her return from Europe, said how much she had enjoyed the rural parts of France, because, among other things, it was "so delightful to hear the French pheasants singing the mayonnaise to the tune of the Los Angelus". It is impossible to amalgamate coal-tar thoroughly with the pulp in the agitating-tank. In metallurgy, 'amalgamate' refers to the combination of mercury with one or both of the precious metals, forming an amalgam, which is an alloy of mercury with another metal. It differs from other alloys, such as brass or bronze, in being made without the aid of heat, inasmuch as mercury is molten at the ordinary temperature. The word comes to us from the Greek through Old French and means 'something soft'. It is a mistake to use technical terms, having a specific meaning, for purposes that are foreign to that meaning. The writer of the quotation is not discussing any combination of metals; he is dealing with the physical process of mixing and is using 'amal-

Jan 1, 1931

By J. D. McClung

INTRODUCTION The ever increasing demand for coal sues that meet exacting specifications has made necessary the installation of thousands of dollars worth of crushing equipment by the coal industry. At one time the operator at- tempted to recover as much lump as possible but today he is confronted with the necessity of crushing to facilitate the mechanical cleaning process and to meet the demand for a variety of uniform sizes. As a matter of fact, about 65 percent of the coal mined in the United States today goes through preparation plants where it is crushed and cleaned. One becomes more aware of the importance of the art of comminution when it is realized that practically all of the operations in mining are involved in comminution in one way or another. Whether the coal is mined conventionally or by continuous miners it is separated from the solid by a breaking, ripping or milling action which essentially amounts to a comminution operation. Even degradation resulting from material handling from the mine working face to the preparation plant might in a broad sense be so classified, Then of course crushing is usually necessary in the plant before the coal is ready to be marketed. THEORY Despite the various comminution operations there is a lack of satisfac- tory information concerning the fundamentals of crushing and their relation to the variable factors associated with the operation. There are certain laws and theories on mechanical reduction, such as those of Rittinger, Kick and Bond that are helpful and useful. The difficulty in developing exact mathematical relationships for specific crusher applications is due to the many variable physical characteristics found in coal. Hardness, as measured by the Hardgrove grindability index, is one parameter that has been used for years to determine the resistance of coal to comminution. While the coal properties as measured by grindability are complex, recent work has shown that a high correlation exists between the grindability of some coals and their petrographic analysis. Early research on the hardness of petrographic entities from an Illinois coal2 demonstrated that durain was the hardest constituent followed by clarain, vitrain and very soft fusain. Other research demonstrated that, for different size fractions of the same coal, a wide variation in hardness commonly exists. For example, the fines in about half of 39 coals studied were softer than their corresponding coarse sues while most of the remaining coals were uniformly hard in all sizes. A few coals contained fines which were harder than their coarser constituents. These variations in hardness give insight into the heterogeneous nature of coal.

Jan 1, 1968

By John W. Stevenson

In gassy coal mines, abandoned worked-out areas are natural reservoirs that may contain air- methane mixtures. The quantity of such mixtures is continuously increasing or decreasing as atmospheric pressure falls or rises. This is in accordance with Boyle's Gas Law, which states that the volume of a perfect gas varies inversely with the absolute pressure. In large, open gob areas without a bleeder ventilation system, atmospheric pressure is a static force acting in all directions. Changes in atmospheric pressure may occur rapidly or slowly, but any change will result in a change in the quantity of gob air-methane mixtures.

Jan 6, 1968

By L. H. Hart

Because of a widely recognized association between breccia pipes of one form or another and many important copper deposits, conditions under which breccia pipes develop have been of great scientific interest for many years. Since these phenomena first attracted attention, many theories have been advanced to explain their origin. This is not unexpected, since it is likely that they have been formed by and under a wide range of conditions. Moreover, the entire subject is confused by the fact that the term breccia pipe is applied to a wide variety of occurrences. To discuss any part of the subject intelligently, therefore, it is necessary to start with definitions of the terms used. In their discussion of the Toquepala deposit, Richard and Courtright have carefully defined the terms they have used in their presentation of a very logical geo- logical history of Toquepala breccias. This is a real contribution, as there is no reference in the literature known to the writer where the history of a series of breccia pipe epochs, confined essentially within one channelway, may be read with the degree of certainty that appears to be possible at Toquepala.

Jan 6, 1958

By C. S. Smith

QUANTITATIVE methods were used to good effect in the earliest days of metallography1-3 but they mysteriously passed into virtual disuse until the important paper4 by Howard and Cohen in 1947. Various devices for the measurements of integrated linear intercepts have been constructed, primarily by petrographers. The hydraulically operated stage designed by the writer5 was satisfactory, but prolonged use caused air bubbles to become entrapped, which introduced back-lash. A new stage has been constructed which avoids this defect and provides better integration when measuring directional structures. This utilizes a circular traverse, and integration is achieved by counting electrical pulses produced by a photocell and a light chopper.* The stage is shown diagramatically in Fig. 1 and in photograph, Fig. 2. It is of simple construction. Mounted on a plate with clamps to fit the stage of a standard metallurgical microscope is a worm and 100-tooth worm gear, the latter supporting the specimen to be measured. The worm is manually actuated by a knob which contains inside it three

Jan 1, 1961

By Zay, Jeffries

THE effect of thoria (ThO2) on grain growth in tungsten was discussed in some detail in a paper presented before this Institute by one, of the authors in 1918.1 In that paper it " was assumed that the, thoria was present in the tungsten entirely as a mechanical mixture. There was no indication in the experiments described that even a trace of the thoria was in solid solution in the tungsten. Langmuir,2 however, observed that thoriated-tungsten filaments under certain conditions showed electron emissions many thousand times greater than unthoriated tungsten at the same temperature. He concluded from his studies that a slight amount of the thoria had dissociated on heating the filament to a temperature near 220°. C. At this temperature and higher, part of the thorium diffuses to the surface of the filament where it evaporates at. a much faster rate relatively, than the tungsten, and also at a rate, nearly as fast as it is brought to the surface by diffusion: If the temperature is lowered to say 1800°,. C., diffusion of the thorium atoms to the surface is more rapid than evaporation, sown adsorbed film of thorium atoms is produced on the surface of the tungsten filament. The electron emission is governed by the outside layer of atoms so the emission from such a filament might be expected to approxi¬mate that of a thorium filament at the same temperature. PRESENCE OF METALLIC THORIUM IN THORIATED TUNGSTEN If the filament containing the adsorbed film of thorium. is heated to a sufficiently high temperature, the thorium atoms evaporate: rapidly and the electron emission becomes more nearly that of tungsten. On cooling again to 1800° C., or thereabouts, the emission 'builds up gradually to a maximum. The filament containing the adsorbed layer of thorium atoms is said to be "activated." By studying the rates of activation under different conditions of prior thermal treatment and at different temperatures, Langmuir was able to arrive at an estimate of the

Jan 1, 1927

By George D. Graffin

The first use of graphite is lost in the mists of time. It was used by primitive man to make drawings on the walls of caves and by the Egyptians to decorate pottery. As early as 1400 A.D. graphite crucibles were being made in the Haffnerzell district of Bavaria. Through the Middle Ages graphite was confused with other minerals, especially galena and molybdenite. Two common names that are still used for the mineral are "Plumbago," meaning leadlike, and "Black Lead." The latter name implied that graphite is either composed of lead or at least contains a large percentage of it. Gessner is credited with having recognized it as a separate mineral in 1565, but its composition was not determined until 1779, when Scheele demonstrated that graphite oxidized to carbon dioxide, thus proving its carbon constitution. In 1789, Werner named it "graphite" from the Greek word "graphein," meaning to write. The United States has long relied on foreign countries for its graphite supplies. This reliance has been due more to the lack of suitable domestic graphites than to any particular preference for buying minerals overseas. Ceylon (now Sri Lanka) graphites were imported as early as 1820, and Madagascar graphites have been imported since the properties on that island were opened up about a hundred years later. Mexico has long supplied the United States with most of its requirements for amorphous graphite. Physical Properties and Classification Graphite is found in laminated, flaky aggregates disseminated in schistose rocks. It also occurs in veins and exhibits a foliated or fibrous structure. Graphite is a black lustrous mineral that crystallizes in the hexagonal system, with rhombohedral symmetry. The crystals have tabular form and are six-sided; the faces are commonly striated. The flakes have perfect basal cleavage and are opaque. When well crystallized, the flakes have a black metallic luster while the amorphous material is black and earthy, with a microcrystalline compactness. The flakes feel greasy. Graphite is an excellent conductor of heat and electricity. It melts at approximately 3500°C and sublimes at about 4500°C. It is combustible in the presence of oxygen between 620° and 670°C, but is stable and chemically inert at ordinary temperatures.

Jan 1, 1975

By L. L. Swift

.It the present time there are four base metals being used for automo-tive bearing alloys. Of course there are numerous variations in the amounts of alloying elements added to each base metal and nearly all of these alloys have the conventional, if not classical, duplex structure; that is, they are composed of a hard constituent embedded in a soft matrix. The well-known theory is that the former will wear well, while the latter will be plastic enough to allow the bearing to be broken in and conform to the contours of the shaft. The requirements of the modern bearing have been most aptly described by W. M. Corse: In order to meet the engineering demands of today a good bearing metal must be able to carry the weight of the shaft and stand up under steady or suddenly applied loads, or even blows ill sorne types of service. A certain amount of plasticity is desired to compensate for minute irregularities in the shaft or bearing surface, and to permit yielding, thereby avoiding dangerous stresses in bearing and shaft and pre-venting overheating and rapid wear of parts. Less plasticity is required in a bearing tuetal if the surfaces of bearings and journals are machined accurately, aligned, and kept in alignment. It is desirable, of course, that a bearing metal have a low coeffi-cicnt of friction. Under most operating conditions the friction depends on the unit, pressure of the bcaring, the speed, the temperature, and the properties of the lubricant. A good bearing metal must have a low rate of wear to reduce the necessity for frequent replacements, and adjustment of the bearings. It must wear more rapidly, however, than the journal or shaft running on it, because replacement of the journal or shaft is more difficult and costly than replacement of the bearing.' The hardness of the bearing alloy is a property closely related to several of the foregoing. With a duplex microstructure, the measurement of hardness with any of the usual commercial devices means little. The Bierbaum method of measuring the hardness of the individual canstituents was developed to fill this need. MICROCHARACTER The Bierbaum MicroCharacter~,~ measures the scratch-hardness of a solid by pulling a weighted diamond point over the surface. The diamond point is ground so that it is the corner of a cube, and Mounted

Jan 1, 1939

By L. L. Swift

.It the present time there are four base metals being used for automo-tive bearing alloys. Of course there are numerous variations in the amounts of alloying elements added to each base metal and nearly all of these alloys have the conventional, if not classical, duplex structure; that is, they are composed of a hard constituent embedded in a soft matrix. The well-known theory is that the former will wear well, while the latter will be plastic enough to allow the bearing to be broken in and conform to the contours of the shaft. The requirements of the modern bearing have been most aptly described by W. M. Corse: In order to meet the engineering demands of today a good bearing metal must be able to carry the weight of the shaft and stand up under steady or suddenly applied loads, or even blows ill sorne types of service. A certain amount of plasticity is desired to compensate for minute irregularities in the shaft or bearing surface, and to permit yielding, thereby avoiding dangerous stresses in bearing and shaft and pre-venting overheating and rapid wear of parts. Less plasticity is required in a bearing tuetal if the surfaces of bearings and journals are machined accurately, aligned, and kept in alignment. It is desirable, of course, that a bearing metal have a low coeffi-cicnt of friction. Under most operating conditions the friction depends on the unit, pressure of the bcaring, the speed, the temperature, and the properties of the lubricant. A good bearing metal must have a low rate of wear to reduce the necessity for frequent replacements, and adjustment of the bearings. It must wear more rapidly, however, than the journal or shaft running on it, because replacement of the journal or shaft is more difficult and costly than replacement of the bearing.' The hardness of the bearing alloy is a property closely related to several of the foregoing. With a duplex microstructure, the measurement of hardness with any of the usual commercial devices means little. The Bierbaum method of measuring the hardness of the individual canstituents was developed to fill this need. MICROCHARACTER The Bierbaum MicroCharacter~,~ measures the scratch-hardness of a solid by pulling a weighted diamond point over the surface. The diamond point is ground so that it is the corner of a cube, and Mounted

Jan 1, 1939

By R. C. Buehl, J. P. Riott, E. P. Shoub

PILOT-PLANT tests have demonstrated that it is possible to produce low-sulphur sponge iron (0.03 to 0.05 per cent sulphur) as a continuous process in an internally fired rotary kiln from iron ore or mill scale; a solid carbonaceous reducing agent; and dolomite to control the sulphur content. The proportion of dolomite employed is small, so that it does not add materially to the cost of the sponge iron. The entire operation is carried out at temperatures well below the melting point of iron, so that the product is discharged in granular form. Compared with other methods for the production of sponge iron, the rotary-kiln method has the advantage of simplicity and low cost of equipment and; in addition, requires little labor for the operation of the process. The pilot-plant equipment used for this work was sufficiently large to demonstrate that the production of low-sulphur sponge iron in rotary kilns is feasible and that the costs are not excessive for applications in which sponge iron has distinct advantages over competing materials. This report constitutes a part of a program by the Bureau of Mines under a special Congressional appropriation for studying gaseous and solid fuel reduction of iron ores. Numerous articles on various phases of these investigations have appeared in Bureau of Mines publications or technical journals. Other articles are being prepared and will be published in the near future. The present program, which is under the supervision of Dr. R. S. Dean, Assistant Director of the Bureau of Mines, was initiated in .1942. However, a considerable portion of the work was a continuation of previous research performed by the Bureau. Previous investigators1-4 utilizing the rotary kiln for the production of sponge iron did not develop a suitable method for controlling the sulphur content. A review of the literature shows that the sulphur content in the product usually exceeded 0.2 -per cent unless reducing agents with very low sulphur contents were employed. This high sulphur value made the product generally undesirable for use as melting stock in electric or open-hearth furnaces. The production of sponge iron in an internally fired rotary kiln has been described in detail in Bureau of Mines Bulletin 2702; consequently, this article will be confined mostly to new features of the process-that is, means for controlling the sulphur content of the sponge iron. Suitable raw materials include iron ores or mill scale; coal or coke for reducing them, and sized dolomite (-20+100-mesh) as the sulphur-controlling agent. A mixture of the raw materials in granular form is fed into the elevated end of the kiln, which is fired axially from the lower or discharge end. In the reducing zone, which is approximately one third the length of the kiln measured from the dis-

Jan 1, 1946

By E. P. Shoub, J. P. Riott, R. C. Buehl

Pilot-plant tests have demonstrated that it is possible to produce low-sulphur sponge iron (0.03 to 0.0; per cent sulphur) as a continuous process in an internally fired rotary kiln from iron ore or mill scale; a solid carbonaceous reducing agent; and dolomite to control the sulphur content. The proportion of dolomite employed is small, so that it does not add materially to the cost of the sponge iron. The entire operation is carried out at temperatures well below the melting point of iron, so that the product is discharged in granular form. Compared with other methods for the production of sponge iron, the rotary-kiln method has the advantage of simplicity and low cost of equipment and, in addition, requires little labor for the operation of the process. The pilot-plant equipment used for this work was sufficiently large to demonstrate that the production of low-sulphur sponge iron in rotary kilns is feasible and that the costs are not excessive for applications in which sponge iron has distinct advantages over competing materials. This report constitutes a part of a program by the Bureau of Mines under a special Congressional appropriation for studying gaseous and solid fuel reduction of iron ores. Numerous articles on various phases of these investigations have appeared in Bureau of Mines publications or technical journals. Other articles are being prepared and will be published in the near future. The present program, which is under the supervision of Dr. R. S. Dean, Assistant Director of the Bureau of Mines, was initiated in 1942. However, a considerable portion of the work was a continuation of previous research performed by the Bureau. Previous investigators1-4 utilizing the rotary kiln for the production of sponge iron did not develop a suitable method for controlling the sulphur content. A review of the literature shows that the sulphur content in the product usually exceeded 0.1 per cent unless reducing agents with very low sulphur contents were employed. This high sulphur value made the product generally undesirable for use as melting stock in electric or open-hearth furnaces. The production of sponge iron in an internally fired rotary kiln has been described in detail in Bureau of Mines Bullelin 2702; consequently, this article will be confined mostly to new features of the process—that is, means for controlling the sulphur content of the sponge iron. Suitable raw materials include iron ores or mill scale; coal or coke for reducing them, and sized dolomite ( — poi-100-mesh) as the sulphur-controlling agent. A mixture of the raw materials in granular form is fed into the elevated end of the kiln, which is fired axially from the lower or discharge end. In the reducing zone, which is approximately one third the length of the kiln measured from the dis-

Jan 1, 1948

By R. C. Buehl, J. P. Riott, E. P. Shoub

Pilot-plant tests have demonstrated that it is possible to produce low-sulphur sponge iron (0.03 to 0.0; per cent sulphur) as a continuous process in an internally fired rotary kiln from iron ore or mill scale; a solid carbonaceous reducing agent; and dolomite to control the sulphur content. The proportion of dolomite employed is small, so that it does not add materially to the cost of the sponge iron. The entire operation is carried out at temperatures well below the melting point of iron, so that the product is discharged in granular form. Compared with other methods for the production of sponge iron, the rotary-kiln method has the advantage of simplicity and low cost of equipment and, in addition, requires little labor for the operation of the process. The pilot-plant equipment used for this work was sufficiently large to demonstrate that the production of low-sulphur sponge iron in rotary kilns is feasible and that the costs are not excessive for applications in which sponge iron has distinct advantages over competing materials. This report constitutes a part of a program by the Bureau of Mines under a special Congressional appropriation for studying gaseous and solid fuel reduction of iron ores. Numerous articles on various phases of these investigations have appeared in Bureau of Mines publications or technical journals. Other articles are being prepared and will be published in the near future. The present program, which is under the supervision of Dr. R. S. Dean, Assistant Director of the Bureau of Mines, was initiated in 1942. However, a considerable portion of the work was a continuation of previous research performed by the Bureau. Previous investigators1-4 utilizing the rotary kiln for the production of sponge iron did not develop a suitable method for controlling the sulphur content. A review of the literature shows that the sulphur content in the product usually exceeded 0.1 per cent unless reducing agents with very low sulphur contents were employed. This high sulphur value made the product generally undesirable for use as melting stock in electric or open-hearth furnaces. The production of sponge iron in an internally fired rotary kiln has been described in detail in Bureau of Mines Bullelin 2702; consequently, this article will be confined mostly to new features of the process—that is, means for controlling the sulphur content of the sponge iron. Suitable raw materials include iron ores or mill scale; coal or coke for reducing them, and sized dolomite ( — poi-100-mesh) as the sulphur-controlling agent. A mixture of the raw materials in granular form is fed into the elevated end of the kiln, which is fired axially from the lower or discharge end. In the reducing zone, which is approximately one third the length of the kiln measured from the dis-

Jan 1, 1948

By V. Lessels, D. J. Buckwalter, D. H. Rose

A cyanide leaching process developed at Michigan Technological University was tested in a 12 to 24 tpd pilot plant. Flowsheet layout and equipment are described. Cyclic operation of leaching, copper precipitation by acidification, and regeneration of the cyanide leaching solution are discussed. Copper extraction and reagent consumption were as predicted by laboratory tests, and the process was proven to be technically feasible. The White Pine Copper Co., a wholly-owned subsidiary of the Copper Range Co., produces copper in the Upper Peninsula of Michigan. Production in 1965 amounted to 138 million pounds of metal. An expansion program now under way will increase this by approximately one half. The highly mechanized room and pillar mine produces 18,000 tons of ore per day, which is treated in a flotation plant. The concentrate is smelted in a reverberatory furnace, the matte is blown in converters to blister copper, and the blister copper is further refined to a uniformly high-quality Lake copper, which is 100% conductive and has a silver content of 25 to 40 oz per ton. The run of the mine ore averages 22.5 lbs of copper per ton with the ore mineral occurring in the form of chalcocite. The nature of the mineralization is such that the sand tailings average a little over 4 lbs of copper per ton. Intensive research has improved copper recovery in the flotation operation to some extent, but at the scale of present operation about 12,000 tons of sands containing over 48,000 lbs of copper go to the tailings pond daily. When the plant expansion is completed, the loss of copper will be somewhat greater. In 1959, the White Pine Copper CO, initiated a study of the recovery of copper in the sand tailings. Inasmuch as the flotation operation was considered to be optimized, a logical approach seemed to be leaching. For various reasons ammonia, ferric chloride, acid, and biological leaching were ruled out as impracticable. This led to a consideration of cyanide leach-

Jan 1, 1968

By W. R. Toeplitz

Probably a more descriptive title would be "Much Ado About Nothing." By "nothing," of course, I refer to the porosity which is the main feature of this type of bearing. Porosity has a decided effect on the manufacturing techniques, the structure and physical properties, the oil content, and on the installation and service of oil-retaining porous bronze bearings. A simple curve can be drawn by plotting specific gravity along the abscissa and percentage of porosity by volume on the ordinate. A bronze composition, analyzing 89 Per cent copper, 9.75 Per cent tin, and 1.25 per cent graphite, has an absolute solid specific gravity of 8.5. At this specific gravity, of course, occurs the point of zero porosity. Conversely, at loo per cent porosity, the specific gravity is zero. A similar curve can be drawn for bearings impregnated with oil; the only change being that the specific gravity at loo per cent oil will be 0.89 if we assume that that is the specific gravity of the lubricant. The curve is useful in determining the oil content by volume for any specific gravity. The normal range of oil content for porous bronze bearings of this composition is from 35 to 16 per cent, which is in the specific gravity range of from 5.8 to 7.3. In addition to the amount of porosity, the type of porosity is important. The first consideration here is that the porosity must be intercommunicating. This can be determined by a number of simple tests. The first method, which is very accurate, is to extract the oil in the bearing by cycling

Jan 1, 1945

By R. D. Nelson, F. E. Bowman

Assumptions are made of ideal mixing and that the density of silver can be obtained by extrapolating reported liquid density-temperature data through the freezing point back to the temperature range of interest. The results of this procedure using liquid silver density data of Kirshenbaum et al.5 are presented in Table I1 where it is observed that agreement is everywhere within <0.1 pct and generally is within 0.05 pct. Because the Sn-Ag alloys are dilute, the assumption of ideal behavior is, therefore, probably justified. In conclusion, the densities of dilute liquid solutions of silver in tin have been determined. Even for concentrations as low as 0.1 pct, the effect of silver on the density of liquid tin is clearly measurable. This work also suggests that for dilute alloys at temperatures far below the freezing point of the solute metal, densities may be accurately calculated by extrapolation of the pure metal data without having recourse to physical measurement on the alloy itself. plutonium having a grain size of about 100 µ. This paper presents data showing that large elongations of fine-grained a Pu can be obtained by using slow deformation rates. Large plasticity, however, of a Pu in compression has been observed.4 Reductions in thickness of 90 pct have been observed with no edge cracking. These large reductions are accompanied by concurrent re-crystallization. The deformation modes, which are quite complex, have been studied extensively by observing the deformation microstructures of polished surfaces that had been deformed in compression.5-7 Although slip apparently is a predominant mode of deformation at room temperature, grain boundary sliding and concurrent recrystallization become more predominant at high a temperatures.4&apos;7 Although recovery occurs,8,9 no grain growth has been reported in a Pu even at temperatures near the a =ß equilibrium temperature (-115oC), which is 0.7 of the calculated melting temperature of a Pu.10 From studies on other materials, it appears that high elongations can be obtained in alloys when the THE purpose of this technical note is to present briefly some data revealing high ductility of a Pu, which is normally considered brittle. The very low ductility of a Pu in tension has been reported by many investigators.&apos;-3 Gardner,1 for example, reported that the total elongation of a Pu at a testing speed of 0.015 ipm is less than 0.1 pct at room temperature and only about 1 pct at 100°C. The only tensile creep studies that have been reported&apos; indicate no large ductility, but they were performed on relatively low purity

Jan 1, 1970

By H. F. Yancey

THE jig may be termed the standard coal-washing machine. Although exact figures on the relative tonnages of coal treated by the various coal-cleaning processes are not available, it is known that a large part of all the coal given special cleaning treatment is handled by jigs. This wide use of the jig warrants a special study of its performance. In this paper are presented the results of an analysis of work done by a three-compartment jig in treating bituminous coal from the Thick Freeport bed in Allegheny County, Pa. Certain systems of washing coal require sizing before washing, while others treat unsized coal. The prevailing practice, however, for the preparation of coking coal from the more easily washed coal is to treat an unsized or natural feed at about -1 in. size and smaller. Under such conditions, the minimum size of particle that is beneficiated has long been and is still a matter of discussion and conjecture. In a careful laboratory investigation Jüngst1 concluded that the practical limit of settling of fine coal is reached at from 0.02 to 0.008 in. On the other hand, Hancock2 has found that single-compartment jigs, used in preparing coal for the domestic market, usually allow most of the heavy (refuse) particles smaller than 1/4 in. to go into the washed coal. He also states that it is impossible with the ordinary coal jig to make any noticeable improvement in the quality of the coal finer than 20 mesh (about 1/30 in.). Because of its importance in coal cleaning, the work described in this paper was undertaken for the purpose of obtaining information on this subject, as a part of the general coal beneficiation program being carried out by the Bureau of Mines.

Jan 4, 1925

The use of the verb in this mood is not as common as formerly: at the time, for example, when the Bible was translated and the plays of Shakespeare were written. Nevertheless it is an essential part of literary English. In editing the &apos;Mining and Scientific Press&apos; I do not insist upon the use of the subjunctive in articles that are contributed from the outside, but it is deemed proper in all our editorial writing. To speak plainly, the subjunctive is a mark of scholarship; it is ignored by those that are not particular in such matters, and unfortunately it is a source of perplexity to many that are entirely unfamiliar with the use of it. Therefore, as an editor, I think it well to allow the indicative mood to be used by contributors in sentences in which, to be strictly correct, the verbs should be in the subjunctive mood. The fact that most subjunctives are indistinguishable in form from indicatives is another cause of trouble to the uninitiated.* For example, the verbs in such phrases as "Suffice it to say", &apos;(So help me God ", and "God save the King" are in the subjunctive. One reason why the subjunctive is becoming uncommon is the growing habit of expressing the subjunctive meaning by aid of auxiliary verbs that are coupled with the infinitive; thus: "It will sate to say" and "May God save the King". The subjunctive is common in subordinate clauses, and that is how it obtained its name, &apos;subjunctive&apos;, meaning

Jan 1, 1931

By T. D. Murphy, G. V. Henderson

The element silicon, with its usual partner, oxygen, plays the same role relative to inorganic materials as carbon and hydrogen play with respect to living organisms. The crystallographic structure of silicon dioxide (SiO2) consists of one atom of silicon well-nigh inseparably bonded to four contiguous atoms of oxygen, a gas of but slightly more than half its atomic weight, forming a three-dimensional network of SiO4 tetrahedra (Dietz, 1968). This wispy arrangement is the fabric of the mineral quartz which is one of the harder, more abrasive, and chemically stable raw materials to be found in Mother Nature&apos;s cupboard. Most of us are vaguely familiar with the observation that nearly 60% of the lithosphere to an approximate depth of 10 miles is composed of these two elements, which proportion actually rises to about 75% if the atmosphere, hydrosphere, and biosphere are included (Parker, 1967). Elemental silicon is a brittle steel-gray metalloid with a density of 2.42 and does not occur in nature. In its limited commercial form, which is still brittle and metallic in appearance, its density drops to 2.33. It combines with oxygen to form the gaseous oxide SiO, or the solid dioxide Si02 (analogous to its congener carbon in CO and CO2); a tetrachloride SiCI4 (analogous to CC14); or, combining with oxygen and one or more metal ions, forms the largest rock-making family of all, the silicates. Further, next to the feldspars, quartz is the most abundant known mineral and, in some form or another, accounts for roughly 12% of surficial terrestrial rock. It is this so-called "free silica" to which your attention is chiefly directed in this chapter. In any such consideration of silica, its several crystalline phases with their attendant differing physical properties appear worthy of delineation. Alpha quartz is the only one of this interesting polymorphic family that is thermodynamically stable at normal pressures and temperatures up to about 573°C. The low phases of tridymite and cristobalite can exist in the so-called metastable state below 117° to 200ºC but seldom occur in nature in these two different crystal forms (Sosman, 1965). Opaline silica, now considered by most researchers to be a variety of cristobalite, occurs in abundance and is the only exception. The three remaining polymorphs, keatite, coesite, and stishovite, also are metastable under ambient conditions. Keatite, however, is not known to occur naturally and has only been synthesized in the laboratory. The other two have been identified in submicron sizes and in microscopic amounts, occurring naturally as a result of high order shock-wave pressures generating quite elevated temperatures --such as might accompany the impact of a large meteorite on a hard sandstone terrain (Chao et al., 1962). An intriguing characteristic of these silica minerals, and one which has very practical applications, is their extremely variable densities. The classic 2.65 specific gravity of alpha quartz drops to 2.20 in tridymite, cristobalite, and lechatelierite (natural silica glass), as well as in many man-made glasses of commerce which are merely noncrystalline or amorphous solids in the form of super-cooled liquids which can no longer change their shapes (Pauling, 1950). It rises again to 2.50 and 2.93 for keatite and coesite, respectively, and finally becomes a reported 4.35 for stishovite-nearly a 50% range in density for the known physical combinations that silica naturally assumes (Frondel, 1962; Konnert et al., 1973; Pecora, 1960). Pursuing its esthetic aspects, briefly, silica is well-represented among gem stones which, to qualify as such, must have the attributes of beauty, durability, and rarity (Jahns, 1983). As quartzose gems usually have but one or, at

Jan 1, 1983