Search Documents

By C. W. Drury, E. J. Hall

The iron-nail method of assaying has been used for a number of years, but has not met with the approval of all assayers. The method possesses advantages which may be given as follows: (1) no preliminary treatment is required; (2) a lead button of proper size can be obtained; (3) it is economical. On the other hand, it has its disadvantages, which may be summed up as follows: (1) it is not applicable to ores containing large amounts of impurities other than sulphur, as practically all the base metals will contaminate the lead button ; (2) the slag is unsatisfactory in the larger number of fusions; (3) the method was known to give low silver results under certain conditions and the gold results were questionable. It was with the idea of determining the extent of this latter disadvantage that the following investigation was undertaken. It is well known that the fusion obtained in the lead assay is far more satisfactory than that in the " nails method" for gold and silver. The principal difference in the charges as a class is the presence of considerable reducing agent in the lead charge, and a limited oxidizing action in the nails charge, dud to PbO. The possibility of improving the nails fusion by simulating the lead charge was the reason for using argol in some tests, even though there were reasons for expecting this would have an objectionable effect on the results. Preparation of the Gold-Bearing Material. The materials containing gold and silver used in the following experiments were prepared rather than selected, in order to have a definite working product excluding undesirable elements. A high-

Jan 1, 1914

By Augustus Locke, Edward H. Perry

In the exploration of a copper deposit by drilling, obvious advantages are to be gained from a distinction between primary and secondary ore.' Perhaps the chief of these is the aid which such a distinction renders in determining where a given hole should stop. The copper assay, often a sufficient guide, cannot always be exclusively relied upon. Primary ores may extend downward indefinitely and may fluctuate in value independently of depth: if primary ores are consistently lean for a considerable vertical distance, there is little reason to expect that, still deeper, they will increase to the commercial grade; on the other hand, rich primary ores may persist uninterruptedly downward or may come in again below a lean interval. Secondary ores, however, have a comparatively limited vertical extent; in a large way enrichment decreases with depth and finally gives out. It follows then, that when a hole descends from profitable ore into ore of less than the commercial minimum, the practical significance of the situation depends upon whether this decrease results from a decrease in secondary enrichment or is a variation in primary content: if the copper of the ore passed through has been chiefly secondary, little is gained in the average case by extending the hole much below the point at which the commercial limit is reached; but, when copper is chiefly primary, due weight must be given to the possibility that, still deeper, the ore may again improve. The distinction between primary and secondary ore may of course be effected through an examination of the drillings. It has been found, however, to be facilitated by curves made by plotting assays against

Jan 1, 1916

By B. S. Butler, H. D. McCaskey

The New London copper mine, about 8 1/2 miles east of Frederick, Md., was visited by the writers for a few hours in the spring of 1909 and the following brief notes on ore specimens collected are presented as a contribution to studies in chalcocite ores. For certain data on the structural and areal geology of this portion of Maryland the writers are under obligation to the unpublished notes and maps of Arthur Keith. The detailed study of the ores is the work of B. S. Butler. The deposit here discussed has many similarities to those of the Virginia district of Virginia and North Carolina, which have been described by Gratonl and Laney,2 except that in the deposits of the New London mine chalcocite is by far the most important ore mineral, while in the Virginia deposits bornite is commonly the most important sulphide. In the New London occurrence calcite is the most important gangue mineral. Field relations The -town of Frederick lies in the center of a narrow belt of limestone ranging in age from Ordovician on the east to Cambrian on the west. This belt is about + mile wide at Noland's Ferry, on the Potomac, and broadens to a width of 3 miles at Frederick. The general direction is east of north. The eastern boundary is, in places, a fault plane along which a series of metamorphic rocks of presumptive pre-Cambrian age have been thrust up. These ancient rocks, for several miles east and west of New London, are phyllites in the main, but closely inter-folded near the New London mine are long, narrow lenses of epidote

Jan 1, 1915

By Peter I. Brooker

Elementary estimation methods in which blocks are assigned values according to a geometrical area of influence concept are investigated for a tabular deposit. This quantitative assessment of the estimation technique is made using Matheron's geostatistics which allows the variance of the error between actual block values and estimated values to be found once the semi-variogram is known. For the deposit in question it is shown that the elementary technique makes poor use of the available information. There is a 20% relative error associated with it, whereas by using the optimal technique of kriging this can be reduced to 9%. An infill drilling program, which might have been suggested on area of influence results, would reduce the estimation variance only marginally over that of the current campaign; the relative error being lowered to 6%. Thus the geostatistical analysis shows this would be an unnecessary expense. The accuracy of an earlier drilling stage is also studied and it is shown that with the information available at the earlier stage block values could have been known with a relative error of 13%. Drilling could have stopped then if this were reckoned a tolerable error level. These results are all obtained for blocks whose size is dictated by the mining engineer and is set at the current grid size. In the area of influence approach smaller blocks are considered as the grid becomes finer and a study of the accuracy of area of influence estimates and kriged estimates for differing block sizes is presented. Between drilling stages more information from which the semi- variogram is calculated becomes available. The sensitivity of the estimation to changes in the semi-variogram parameters between earlier and current drilling programs is investigated.

Jan 1, 1977

By C. M. Means

Considering the hazard involved in mining operations, statistics show that a very small percentage of accidents is chargeable to electricity. These accidents do represent quite a large percentage of those that are preventable and they are the direct result of the introduction, for purely economical reasons, of a dangerous element. The introduction of electricity in mines should decrease the hazard, and in no case should electricity be applied to the mechanical operation of equipment if by so doing the dangers incidental to mining are increased. The greater number of accidents are the result of persons coming in contact with exposed conductors at potentials varying from 258 to 508 volts direct current. The use of alternating current at higher potentials than these is quite common in large mines, but it is very rare that an accident happens from this source. This is explained by the fact that where these high voltages are warranted, proper precautions are taken, and the installations are directed by those who fully appreciate the dangers incidental to the work. Direct current is in much more general use than alternating current because of its adaptability to haulage locomotives and the low cost of installation in small operations. We are, however, coming to a more extended application of alternating current for the operation of mechanical devices used in connection with mining. Our underground direct-current wiring system is an evolution from the surface trolley and feeder systems. This is probably due to the fact that our earlier successful applications were electric locomotives, which required the use of a trolley wire. The trolley current has been almost banished from industrial establishments on the surface because of the hazard involved, yet we use it indiscriminately underground, where the dangers from accidental contact or fire are infinitely greater., This does not mean that the underground trolley systems should be eliminated, but it does imply the proper safeguarding of such equipment as is necessarily a part of the trolley systems. It is a fact that the men now employed in the installation and maintenance of mining equipment may be in many cases incompetent or not thoroughly familiar with the work, but they are the men who must do the work and, in order to do it properly, it is necessary that they be educated

Jan 1, 1915

By Z. F. Danes

Combination of gravity data and density logs makes it possible to determine the structural relief. Under a wide class of geologic conditions, the solution is unique, or limited to a single parametric system of solutions. As a useful byproduct, the method yields a new way to construct derivative maps, continue the field up or down, subtract regional anomalies, and perform smoothing. In the past, the problem of interpreting gravity anomalies in terms of structural geology was solved along two main lines: 1) A body of a certain shape and density contrast was assumed and the corresponding gravity anomaly calculated, analytically for simple bodies, graphically and/or numerically for more complex ones; then the computed anomaly was compared with the observed one, and the assumed shape corrected according to the differences between the two. 2) The anomaly is assumed to come from a warped interface between two media of different density; the relief of the warping is assumed small compared to the depth of burial, so that the structure can be approximated by a flat horizontal surface of variable density distribution. The first method is a standard technique, described in every text book on applied geophysics, and is well applicable, for bodies with predominant vertical dimension. The second one, probably first used by Tsuboi and Fuchida,' is mathematically more elegant. It applies to the fashionable field of integral transforms (Bullard and Cooper, 2 Tomoda and Aki, 3 Dean 4) and is useful mainly in cases when the vertical relief of the structures is comparatively small. 30th methods, tacitly or openly, assume a density discontinuity across the boundary of the two media, while within each medium the density is constant. However, the recent invention of the gamma-gamma

Jan 1, 1962

By Willard S. Morse

The purpose of this paper is to record the results obtained in the use of the Russell process at Aspen, Colo., covering a period of fourteen months, from November, 1891, to December, 1892, during which time over 30,000 tons of ore, purchased outright, on sample and assay, were treated. No explanation of results will be attempted, nor will the chemistry of the process be discussed. The plant was designed by C. A. Stetefeldt, of San Francisco, and built by the owners by day-labor. The entire plant is run by water-power, supplied by a flume 3600 feet long, and a pipe-line 2200 feet long, with a head of 170 feet. A Pelton water-wheel, 8 feet in diameter, is used, from which power is transmitted by wire-rope to the main counter-shaft in the mill, a distance of about 250 feet. From the mill to the samplingworks, about 150 feet, power is also transmitted by a wirerope. A Pelton water-wheel, 3 feet in diameter, supplies power to the dynamo for lighting the plant. The works are located adjoining the Santa Fe railroad tracks, and all ore and supplies are unloaded directly from the cars to the works. The sampling-works are provided with crushers and rolls, the latter being used only on samples, and not on the entire ore. The Cornish hand-quartering method is used in sampling ore for purchase. After crushing and sampling, the ore goes to the bedding-floor, where it is made up into mixtures suitable for the mill. The drying-plant consists of four Stetefeldt double shelfdryers, six shelves high, and is provided with dust-chambers and a stack 65 feet high for draft. These dryers are fired with gas

Jan 1, 1896

By S. G. Gibbs

A new method for predicting the behavior of sucker-rod pumping systems is presented. The pumping system is described by a flexible mathematical model which is solved by means of partial diflerence equations with the aid of computers. Polished rod and intermediate-depth dynamometer cards can be calculated for various bottom-hole pump conditions. The technique permits simulation of a wide variety of operating conditions, both normal and abnormal. The data generated with the new technique are useful in refining the criteria for design and operation of sucker-rod systms. INTRODUCTION Sucker-rod pumping systems are used in approximately 90 per cent of artificially lifted wells. In view of this wide application, it behooves the industry to have a fundamental understanding of the sucker-rod pumping process. Oddly enough, our understanding has been rather superficial. This is evidenced by the semi-empirical formulas which have been used as the basis for design and operation of sucker-rod installations. Thoueh- we have realized the limitations of our methods for many years, it has not been computationally feasible to use more refined techniques. With the advent and widespread use of digital computers, it is now possible to handle the mathematical problems associated with sucker-rod pumping. This paper summarizes a computer-oriented method which can provide greater insight into the sucker-rod pumping process. It is hoped that this technique, and techniques which may evolve from it, will prove to be the tool needed by industry to obtain the most efficient use of rod pumping equipment. THE MATHEMATICAL MODEL Prediction of sucker-rod system behavior involves the solution of a boundary value problem. Such a problem includes a differential equation and a set of boundary conditions. For the sucker-rod problem, the wave equation is used, together with boundary conditions which describe the initial stress and velocity of the sucker rods, the motion of the polished rod and the operation of the down-hole pump. Of these items, the wave equation, the polished rod motion condition and the down-hole pump conditions are of primary importance. Discussion of the mathematical model centers about these factors. ROD STRING SIMULATION WITH THE WAVE EQUATION The one-dimensional wave equation with viscous damp- is used in the sucker-rod boundary value problem to simulate the behavior of the rod string. This equation describes the longitudinal vibrations in a long slender rod and, hence, is ideal for the sucker-rod application. Its use incorporates into the mathematical model the phenomenon of force wave reflection, which is an important characteristic of real systems. The viscous damping effect postulated in Eq. 1 yields good solutions, even though nonviscous effects such as coulcomb friction and hysteresis loss in the rod material are present. Fortunately, the nonviscous effects are relatively small, so the viscous damping approximation used in the wave equation is adequate. The coefficient v is a dimensionless damping factor which is found in field measurements to vary over fairly narrow limits. For mathematical convenience the gravity term is omitted in Eq. 1. The effect of gravity on rod load and stretch can be treated separately, as will be noted later. Since Eq. 1 is linear, the legitimacy of this procedure is easy to demonstrate. POLlSHED ROD MOTION SIMULATION The motion of the polished rod is determined by the geometry of the surface pumping unit and the torque-speed characteristics of its prime mover. By determining the motion of the polished rod, we formulate an important boundary condition. From trigonometrical considerations it can be shown that the position of the polished rod vs crank angle 0 is given by (see Fig. 1) These equations are obtained from the general solution of the "four-bar" linkage problem and can be used to describe the kinematics of any modern beam pumping unit.' If prime mover speed variations are disregarded, the angular velocity of the crank is constant, and Eq. 2 can be used to predict the position of the polished rod vs time. However, the constant-speed condition leading to constant crank angular velocity is only approached in practice: hence, it is better to make provisions for prime mover speed variations in the mathematical model. The speed at which the prime mover runs is determined by its torque-speed characteristics and the torque imposed upon it. The torque that the prime mover "feels" is the net torque arising from the polished rod load and the opposing torque from the counterbalance effect. The

J. Chipman (Massachusetts Institute of Technology, Cambridge, Mass.)—The fact that the experimental work has been applied to copper rather than iron and that the paper is presented to the Iron and Steel Division, I regard as rather significant. It shows the unity of metallurgy and the fallacy of trying to cut it up by metals. This result for the solubility of sulphur in molten copper correlates with Professor Schuhmann's finding that the published data on the other side of the copper-sulphur miscibility gap are also in error. I should like to ask the author to say a little bit more about the sulphur capacity of the slag. T. Rosenqvist (author's reply)-—I hope that Dr. Chipman will find the derivation of the expression for sulphur capacity more clearly explained in the printed version of the paper than in the oral discussion at the meeting. I feel that this quantity, which actually is the ratio of two activities, can be measured more easily than the individual activities. Even if the ratio CaO/CaS is chosen as the standard state, the expression can be used for any slag, even for slags completely free of lime, and it represents a way to put the desulphurizing power of all slag constituents into one bag. Some doubt has been expressed as to whether oxygen ions really exist in calcium oxide and in molten slags. From a thermodynamic view point that question is of minor importance. The term oxygen ion activity, or any activity for that matter, is defined rigorously by the equation: activity = exp u/RT, where u is the change in free energy connected with the transfer of one mol of ions from the standard state into the slag. Whatever happens to the ion in the slag is of no concern to the thermodynamicist. Regardless of whether the ion is "free" in the slag or not, or whether it is present in a very small amount, its activity can always be expressed, and for a thermo- dynamic calculation that is all we need. However, ionic activities will only be of some real value if they are simple functions of the slag composition, or can be measured easily. Concerning the real nature of the oxygen in the slag, my feeling is that the oxygen atom has a rather multiplex nature depending on how strongly it is tied by covalent forces or polarized by the other atoms or ions present. The oxides of iron, cobalt, and nickel differ from calcium oxide and blast furnace slags as to the amount of free electrons that can give rise to electronic conductivity. In slags we know that the conductivity is mostly ionic. The fact that reversible emf's can be obtained with oxygen electrodes in certain salt melts, indicates a significant amount of oxygen ions in these melts. But extended work, e.g. polaragraphic studies and measurements of transference number; are needed to obtain quantitative information about the real structure of the slags. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—-With reference to the ion, it might be well to remember Dr. Moses Gomberg. All of his life he had no use for the ionization theory and he contributed greatly to the field of chemistry on the assumption there was no such thing as ions. I do not think we have to worry about whether the oxygen is ionic or not. I think one thing specifically should be brought to your attention and this I think is one of the important contributions of Dr. Rosenqvist. He pointed out what we know as oxygen potentials or what is described as oxygen potentials. I have used this concept for a long period of time and I want to state that if this concept is properly applied, it vitiates much of what we have in the literature, or makes our usual ideas regarding oxidation seem primitive. That one thing is more valuable than almost all the rest of the discussion as a fundamental basis on which to build a reasonable in-

Jan 1, 1952

By Frederic Benard

The treatment of Balbach-Thum slimes at Copper Cliff by the Ontario Refining Co, is of interest because it differs considerably from methods usually employed for the recovery of fine gold from parting-plant slimes. Owing to the comparatively high percentages of palladium and platinum, wet methods are used to remover the greater proportion of these metals before electrolytic refining in the Wohlwill cells. The Plant The platinum-metals department, Wohlwill room, and gold-melting room extend along the north side of the silver refinery and are separated from the parting plant by a glass partition (Figs. 1 and 2). The platinum-metals department resembles a laboratory built on a large scale, with the various pieces of equipment laid out on terraces to facilitate handling. Because of the corrosive nature of the solutions, chemical stoneware is used throughout. Elevation of acids is accomplished by means of Mariotte bottles. On the top level are three steam-jacketed stoneware kettles of 50-gal. capacity, also a packed tower. One kettle is used for digesting the slimes while the remaining kettles are used for precipitating the gold. The dissolver is equippcd with a treated concrete hood, which is connected to the flue system. Gases are drawn off through the packed tower by means of a 6-in. stoneware exhaust fan. A 15 per cent solution of sodium carbonate is continually circulated through the tower. On the intermediate level are two suition filters, one for removing silver chloride and the other for the gold sand. The filter medium consists of an asbestos pad covered with a filter paper on which is a layer of twill. On the bottom level are two rectangular cementation tanks, 24 by 48 by 24 in. deep, and a suction filter used for removing the platinum-metal concentrates. The circulating pump for the packed tower is also here. Suction is provided by a vacuum pump having a capacity of 8 cu. ft. at 20-in. vacuum.

Jan 1, 1944

By Robert Mehl

METALLURGISTS are properly interested in papers dealing with subjects ranging from the theories of the metallic state to very practical details on the use of metals. A review of theoretical metallurgy naturally excludes papers concerned with the usefulness of metals and limits itself to those concerned purely with the science of metals. Even in this more limited field the reviewer is confronted with thousands of papers dealing with facts and theories of metallic behavior, from which he can select only a few hundred. The selection is necessarily highly arbitrary. Certain classes of papers definitely fall within the scope of this review. Thus, papers on the deformation of metals, on the structure of alloys, on recrystallization, to select only a few, are fully represented. Other subjects, which verge on what is generally accepted as the science of metals, such as the magnetic properties of metals, the less familiar electrical properties and theories, adsorption of gases by metal surfaces, and the like, are treated scantily. Particular attention is given to reviews of subjects that fall with in the groups chosen; in a summary such as this, which is largely in the nature of a progress report, capably written reviews are of importance, particularly since the monograph and text book literature is so meager in this field.

Jan 1, 1935

By Frederic Benard

THE treatment of Balbach-Thum slimes at Copper Cliff by the Ontario Refining Co, is of interest because it differs considerably from methods usually employed for the recovery of fine gold from parting-plant slimes. Owing to the comparatively high percentages of palladium and platinum, wet methods are used to remove the greater proportion of these metals before electrolytic refining in the Wohlwill cells. THE PLANT The platinum-metals department, Wohlwill room, and gold-melting room extend along the north side of the silver refinery and are separated from the parting plant by a glass partition (Figs. 1 and 2). The platinum-metals department resembles a laboratory built on a large scale, with the various pieces of equipment laid out on terraces to facilitate handling. . Because of the corrosive nature of the solutions, chemical stoneware is used throughout. Elevation of acids is accomplished by means of Mariotte bottles. On the top level are three steam-jacketed stoneware kettles of 50-gal. capacity, also a packed tower. One kettle is used for digesting the slimes while the remaining kettles are used for precipitating the gold. The dissolver is equipped with a treated concrete hood, which is connected to the flue system. Gases are drawn off through the packed tower by means of a 6-in. stoneware exhaust fan. A 15 per cent solution of sodium carbonate is continually circulated through the tower. On the intermediate level are two suction filters, one for removing silver chloride and the other for the gold sand. The filter medium consists of an asbestos pad covered with a filter paper on which is a layer of twill. On the bottom level are two rectangular cementation tanks, 24 by 48 by 24 in. deep, and a suction filter used for removing the platinum-metal concentrates. The circulating pump for the packed tower is also here. Suction is provided by a vacuum pump having a capacity of 8 cu. ft. at 20-in. vacuum.

Jan 1, 1938

By Charles W. Tandy, Wm. I. Weisman

Sodium sulfate is an important industrial chemical, being one of perhaps a dozen or so chemical commodities that are produced and consumed in the United States in quantities exceeding one million short tons per year. In recent years over half of the country's production of sodium sulfate has come from natural sources, whereas 20 years ago only 25% was derived from these sources. Production of natural sodium sulfate from various types of deposits is the main source of this chemical in Canada and Mexico, and probably in Argentina, Chile, and the USSR. [Table 1] illustrates the growth in production of natural sodium sulfate in the United States. Mineralogy and Physical Properties Sodium sulfate is widespread in occurrence and is a common constituent of many mineral waters, as well as seawater. Many of the saline or alkali lakes throughout the world contain varying amounts of sodium sulfate. In its natural form it is found as the hydrous salt, mirabilite, commonly called Glauber's salt, and as thenardite, the anhydrous variety. The largest quantities occur in the form of mirabilite. Sodium sulfate is found in varying degrees of purity, from theoretically pure efflorescent crystals of mirabilite to combinations and admixtures of other salts and impurities. It is a common constituent of some brines, and it is from this source that much is extracted commercially. Sodium sulfate is also found combined with other compounds, such as the mineral glauberite, the double salt of anhydrous sodium and calcium sulfate, and blödite, the double salt of sodium sulfate and magnesium sulfate. While these and other minerals containing sodium sulfate are not economically important, they are of interest because of their frequent occurrence. The reader is referred to other publications (Cole, 1926; Dana, 1932; Grabau, 1920) for descriptions of these minerals. Only the two economically important minerals, mirabilite and thenardite, will be described herein. Mirabilite, Na2SO4 • 10H2O, contains 55.9% water of crystallization. It is noted for its efflorescence or spontaneous loss of water. On

Jan 1, 1975

By V. F. Hollister

The Queen Charlotte gold deposit (also known as the Specogna, Babe, or Cinola) was discovered in late 1970 by Efrem Specogna and Johnny Trico. They were prospecting along the trace of the Sandspit fault, and they sampled jarositic material that included veins from the fault zone. Their assays included some good gold values. They located the Babe Claims in 1971 and optioned them to Kennco Explorations Ltd. Kennco conducted stream sediment and soil geochem studies, geological mapping and drilling of 55.2 m (181 ft) in two drill holes. Kennco withdrew from the property, and by 1977, Cominco, Placer Development, Silver Standard, and Quintana Minerals had each successively worked on the deposit. Consolidated Cinola Mines bought the claims in 1977 and completed exploration of the deposit ultimately in a joint venture arrangement with Energy Reserves. Energy Reserves entered in late 1979, and by 1983, a total of 200 surface and 12 underground drill holes had been completed, totaling 28 600 m (93,832 ft). In addition, a 461.9 m (1515 ft) adit was driven in the ore body. Reserves published by Cinola aggregate 34 Mt (37 million st) of 1.7 g (0.060 oz) Au per tonne. All industry geologists working in the area agree that the Queen Charlotte gold is an epithermal gold deposit in porous volcaniclastic and clastic rocks that is genetically related to a Miocene-Pliocene rhyolite plug. The geologic description here follows the oral presentation made by G. G. Richards, J. S. Christie, and M. R. Wolfhard at a 1976 CIM meeting. Additional comments by the late C. S. Ney of Kennco Explorations are included with the Richards, Christie, and Wolfhard data to complete the geologic set- ting. The attached reprint by Champigny and Sinclair (1 980) provides additional data on the deposit. The Queen Charlotte (Babe, Specogna, or Cinola) gold deposit is located on Graham Island in the northern Charlotte Islands, at the fault boundary of the Skidegate plateau and the Charlotte lowlands. The Sandspit fault marks the physiographic boundary, and it is intruded by rhyolite porphyry at the deposit. Because displaced geochem anomalies, drain- age patterns, and topography suggest dextral and east side down movement for the fault, exposed east block rocks are younger than rocks west of the fault. The east block, which included the ore deposit, is a lowland largely masked by unconsolidated Pleistocene and Recent clastic rocks. Rocks west of the rhyolite plug, on the Skidegate plateau, are Cretaceous carbonaceous and calcareous shale unconformably overlain by a thin veneer of rhyolite tuff. The deposit is about 100 m (328 ft) above sea level. GEOLOGIC SETTING At the ore deposit, the Sandspit fault is a complex structure. However, lithologies on either side of the fault-controlled rhyolite porphyry plug are distinct. West of the rhyolite, the upper member of the Cretaceous Haida formation shale is the most common rock type. The member is composed of dark grey to black, poorly consolidated, and thinly bedded carbonaceous and calcareous shale. The sequence is silicified to an argillite or a hornfels near the rhyolite. West of the rhyolite porphyry plug, but not importantly involved in the mineralization, is a thin masking cover of rhyolite tuff. The tuff unconformably succeeds the cretaceous shale, but it is largely eroded in the mine area. East of the fault-controlled rhyolite porphyry plug is a thick section of conglomerate and sandstone of the Miocene- Pliocene Skonun formation. The ore body occurs within the coarse clastics, the rhyolite intrusive as the western boundary. Ore is entirely contained within the clastics. Original permeability of the clastic rocks was a major control for ore deposition and alteration, and for that reason, the Skonun formation is described in greater detail. The Skonun formation clastics unconformably overlie Haida shale. The Skonun is at least 300 m (984 ft) thick in the mine area, where it trends northerly and dips easterly 15º to 25º. The sequence is about 62 percent conglomerate, 3 1 percent coarse arkosic sandstone, and 7 percent interbedded siltstone and sandstone. Contacts between adjacent beds are generally sharp. Stratigraphic correlations between drill

Jan 1, 1985

By H. R. Drullard

TO obtain the best results from hammer drills, close attention must be paid to two factors in drill maintenance, which are of equal importance; one is lubrication, the other is the shank. With the exception of stoping drills, most modern rock drills require both oil and grease. The oil ports are in the lubricator, on or behind the hammer cylinder; the grease port for the lubrication of the chuck sleeve and rotating mechanism is on the chuck end. Ordinary machine oil is not adapted to rock drills; a heavier more gelatinous oil such as castor machine oil or liquid grease should be used. The lubricators should be filled once for every 12 or 14 ft. (3.5 to 4 m.) of hole drilled. Grease guns should be used to fill the port in the chuck end once a shift; a medium (No. 3) grease is well adapted to this purpose. Hard grease must not be put into the lubricators, as it will not flow through that part. Contrary to the popular belief, oiling a machine once or twice a shift does not provide sufficient lubrication; the drills should be oiled once for every 12 or 14 ft. of hole drilled. The rotating handle of a stoping drill is an oil reservoir and is provided with a port for oiling. The rotating handle is packed with wick-ing, or similar material, which causes the oil to feed slowly from the handle to the other parts of the machine. Stoping drills require oil at least twice a shift; lighter oils than castor, such as Arctic Ammonia, may be used. Drills used in shaft sinking can be oiled satisfactorily by placing a good-sized, drop, sight lubricator on the station above the sinking operations and connecting it with the air-line supplying the sinking drills. If this lubricator is properly filled and adjusted, a uniform oiling of the sinking machines will be effected without the necessity of oiling the drills individually. The grease end should be filled at the station or surface before each drilling period. The shift boss should see that the machines are greased and also that the lubricators at the station function properly. The life of the air-drill hose is somewhat shortened by this method, as oil attacks the inner tube; but as some oil is always present in the compressed air, this is not a serious objection to the method.

Jan 1, 1922

By H. B. Charmbury, D. R. Mitchell

Recovery of fine coal from solids reporting to wash water has become increasingly important. These solids range from about 28 mesh to 0 and constitute 3 to 7 pct by weight of the feed tonnage to a coal preparation plant. In the past they were usually wasted to streams, but present clean stream legislation makes it necessary to remove them from the wash water and, if economically possible, recover the associated coal as a saleable product. Where these solids are not wasted to streams or to slime ponds they are recovered by thickeners and filters. Since filter cake is often high in ash or sulfur, or both, it is not readily marketed or used. Common practice is to mix it with other plant products, generally slack or cleaned run-of-mine. Uniform blending is difficult, not only because the impurity is usually high, but also because during certain operating periods it is possible to get a concentration of this filter cake in a railroad or barge. At some plants filter cake has been derived from the froth flotation clean-up of Dorr thickener underflow. The operating circuits required for a froth flotation plant make this a comparatively high-cost treatment, and in the last few years experiments have been carried out with bulk oil methods. These also are quite expensive and lend themselves only to special situations. Table I gives some characteristics of thickener underflows for plants in the Pittsburgh area treating Pittsburgh seam coal. It will be noted that there is a concentration of impurities in the -200 mesh sizes.

Jan 1, 1960

Discussion of the paper Of ROBERT H. BEDFORD and WILLIAM HAGUE, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 92, August, 1914, pp. 1807 to 1816. W. L. SAUNDERS, New York, N. Y. (communication to the Secretary *) . -Messrs. Bedford and Hague have given us a very interesting and practical paper. No better excuse for such a paper could be desired than the statement made that the expense of drilling. in this mine is one-third of the cost of delivering the ore at the mill. This statement. should be written in red letters, because it applies to a great many mines besides the one referred to and because it is generally true that in a mining plant, as also in papers read before the Institute, more attention by fat is given to the metallurgical side of mining than to the excavation of the ore, and no study of the excavation work is properly made that does not involve a careful inquiry into the merits of the rock drill used. Next in importance to the selection of a good rock drill, in a case where the actual drilling cost is one-third the cost of delivering the ore, is that. the drill should be maintained in order and kept up to its highest efficiency. The best rock chill may run down in efficiency through accidents, wear, or other conditions which are sometimes beyond supervision or control. The machine is usually in the hands of men who know how to get workout of it, not men who know how it works. The best drill runners are not machinists,. but miners. They could not tell you how the valve operates or the principle of the rotation, but they know how to get the work done. A testing machine, particularly the type described in this paper, may he of the greatest value in maintaining a uniform state of efficiency.

Jan 11, 1914

By D. H. Baldwin, R. E. Reed-Hill

Six compositions of polycrystalline ZY-0 alloys, containing up to 4.2 at. pct 0, were tested in tension between 77° and 600° K. The data obtained from each of the compositions corresponded closely to a rela-ion between yield stress and absolute temperature of the form In s/so = BT, where oo is the yield stress extrapolated to zero degrees and B is a constant. In agreement with others who have observed this relationship, it is shown that the activation energy may be expressed as Ho In so/s. In the present specimens Ho is approximately 18,000 cal per mole and is apparently independent of temperature and composition inside the limits of the investigation. It is also demonstrated that this form of activation energy cowesponds to a strain rate sensitivity parameter RT/Ho. Oxygen was also noted to have an effect upon the operative deformation mechanisms. With increasing oxygen concentration there was an increased tendency to observe both nonbasal slip and cross-slip phenomena. Oxygen does not seriously inhibit twinning more than it does slip. Twins were observed in all specimens tested. It is becoming increasingly evident that interstitial atoms in solid solution are able to interact strongly with mobile dislocations. Stein, Low, and seybolt,&apos; have shown that, if the carbon concentration in bcc iron is lowered below the solubility limit, its flow stress temperature dependence is markedly reduced. This suggests that carbon atoms in interstitial solid solution may be responsible for the pronounced temperature dependence of the flow stress normally observed in iron. This view has recently been challenged by Leslie and sober2 who observed a strong flow stress temperature dependence in iron to which a trace of titanium had been added in order to remove carbon atoms from solution. Since the interstitial concentration must be reduced below approximately 1 ppm in order to produce a pronounced effect on the flow stress temperature dependence,&apos; studies of the effect of interstitials on the flow stress in iron necessarily involve serious experimental difficulties in alloy preparation. There are other metals, however, in which strong effects of interstitial solutes upon both the flow stress and its temperature dependence are observed. Of particular significance is zirconium which, according to Domagala and Mcpherson, 3 is capable of dissolving 28.6 at. pct O. The O-Zr alloy system is an almost ideal system for studying the interaction of interstitial atoms with deformation modes since it is possible to form alloys capable of study over an extensive range of compositions. Mills has made such a study using single crystals oriented primarily for single prismatic slip4 and has found an effect of oxygen concentration on the flow stress temperature dependence analogous to that observed in iron due to carbon by Stein, Low, and Seybolt. The present paper is specifically concerned with the effect of oxygen on deformation in polycrystalline zirconium. Although plastic flow in this type of specimen is much more complex than that reported for the single-crystal work, and involves both slip (on several different types of planes) and mechanical twinning, the results of this investigation are in general agreement with the single-crystal observations concerning the effect of oxygen on the temperature dependence of the flow stress. In addition, they also demonstrate that oxygen affects the acting deformation systems. This is in contrast to single-crystal results4 that showed only single slip on a prism plane. EXPERIMENTAL PROCEDURE Material. High-purity hot-rolled zirconium strip, 0.2 in. thick by 4 in. wide, of 0.10-mm average grain diameter, was used for forming alloys. It was obtained from the Carborundum Metals Co., Akron, N.Y., whose analysis indicated the major impurities were, in wt ppm: Hf, 540, C, 145; Fe, 100; and 0, <80. The plate texture was similar to a wire texture, with basal planes generally parallel to the rolling direction and basal poles randomly distributed about the rolling direction. The heat treatments described below did not appreciably alter the basic texture. specimen Preparation. Small threaded-end tensile specimens were machined from the plate with axes perpendicular to the rolling direction. These transverse specimens had gage sections 1 in. long by 0.060 in. in diam. The small gage section diameter was dictated by the fact that the alloys were formed by dif-

Jan 1, 1969

By M. R. Tek, K. H. Coats, D. L. Katz

A large number of boundary value problems encountcred in unsteady-state heat transfer, fluid flow through porous media, neutron diffusion and mass transfer involve the solution of a linear, parabolic partial differential equation commonly refcrred to as the diffusivity equation, where U is the dependent potential variable. K is the diffusivity (hydraulic, thermal, neutron, etc.) and 1 is the time variablc. Solutions to Eq. I are available in the literature for a wide variety of initial and houndary conditions. The great majority of these solutions are ohtained for geometric boundaries corresponding to linear. cylindrical or spherical flow models. A typical engineering application where the solution to Eq. 1 is required is the calculation of underground water encroachment across the boundaries of oil or natural gas reservoirs, In this particular area of application, the reservoir boundary is invariably approximated by circular geometry. However. the areal shape of many reservoirs can be better approximated by elliptic rather than circular boundaries. Thus the need for a general method of solving the diffusivity equation in elliptic coordinates arises in this problem as well as in other engineering applications involving elliptic boundaries. The solution to the diffusivity equation usually in volves the Error Function for the linear flow model, Bessel functions for the radial flow model and trigonometric or Legendre functions for the spherical flow model. It is well known that the general solution to the diffusivity equation in elliptic coordinates involves Mathieu functions. The significance of Mathieu functions in the analytical treatment of the diffusivity equation in elliptic coordinates is discussed in the literature However, these references do not providc analytical solutions useful in practical engineering problems. The objectives of this papcr are the development of the equations describing the unsteady-state liquid flow through a porous medium with an elliptic inner boun- dary, the development of a numerical method of solving these equations and, finally, a comparison of the water encroachment quantities calculated from the elliptic flow equation with those calculated from the radial flow equation. While the specific problem treated in this paper relates to unsteady-state liquid flow through a porous medium, the basic equations and computational techniques devcloped will apply equally well to problems occurring in the other areas of engincering interest mentioned previously. The solution given here is limited to a single case in which thc outer boundary encloses an area 100 times that of the inner boundary. DESCRIPTION OF THE FLOW MODEL Fig. 1 shows the flow model upon which the calcu lations presented in this paper are based. The inncr and outer houndaries of the flow model are represented by two confocal ellipses with major and minor axes, respectively, equal to 2a1, 2b1, and 2a, and 26,. The height of the elliptic cylinder flow model is denoted by 17. The following assumptions are employed in the development 01 the equations governing the unsteady-state liquid flow through the described flow model. 1. Uniform porosity and permeability throughout the flow model

By F. W. Lake

The ultimate production from a natural reservoir of petroleum is inversely proportional to the gas-oil ratios existing during the producing life of the reservoir whenever gas is the major expulsive force in the recovery. In other words, in the period during which gas is the major expulsive force the ultimate production will be increased if the gas-oil ratio is decreased, and vice versa. This condition prevails in the greater number of the present producing districts. While this relation is difficult to prove from actual operation, on account of the present paucity of detailed observations, it must be admitted after a study of the forces and conditions governing the recovery of petroleum from natural reservoirs. Where gas and oil exist under pressure in sand interstices and water movement is not freely possible, the force expended in moving the oil to the well is the expansion and movement of the gas through the pressure differential existing between the interior of the reservoir and the well. If pressure and solution conditions in the untapped reservoir are such that the relation between gas and oil volumes at atmospheric conditions is as 100:1; and if during the producing period, until the gas is exhausted, the relation between the gas and oil volumes produced is 300:1, it follows that only one-third of the oil has been produced and the remaining two-thirds cannot be recovered unless some extraneous force is introduced into the reservoir. This serves to illustrate the importance of gas-oil ratio control during normal producing operations. Gas-oil Ratio Control Eliminating natural conditions in a reservoir, which govern gas-oil ratios, such as the physical properties of the oil and gas, the physical characteristics of the reservoir strata and the original pressure and solution conditions in the reservoir, which cannot be controlled by operation practice; and also eliminating operating conditions that apply to the reservoir as a whole, such as well spacing, well locations, relative completion dates, various penetrations and drilling practice; there remains but one condition in each well that influences the gas-oil ratio and that is

Jan 1, 1928