Search Documents

By V. R. Garfias, R. V. Whetzel

It has been repeatedly questioned whether estimates of oil reserves are of any practical value, as the greater number of such calculations previously made have subsequently been proved to be grossly inaccurate. But even admitting partial justification for such statements, it must be evident that some idea, however approximate, of the available reserves of essential minerals—petroleum included—is of vital importance in mapping their development and the future trend of the related industries, particularly if it is kept constantly in mind that these estimates are not only never intended as a final word but must continually be subject to revision in accordance with the changes in their component factors. The value of these estimates, therefore, hinges on the clear understanding of what is meant by reserves and that the figures can only apply within the limited time when the controlling factors remain unchanged. It should be understood, further, that while estimates of possible and probable oil deposits are as a rule but idle conjectures, appraisals of proven oil reserves can undoubtedly be made with an ever-increasing degree of accuracy. And it is with this in mind that in the present study the endeavor has been to estimate only the world's proven oil reserves and to leave out of consideration the questionable volume of the probable and possible oil reserves. Such a survey presupposes further a clear distinction between the known amount of oil underground in proven fields at any one time, and the proven reserves: the portion that can be economically brought to the surface and made available for utilization. Only a fraction of the petroleum stored underground in proven fields— usually associated with natural gas—is or can be economically brought to the surface, and not all of the oik brought to the surface is economically utilized; also, although practically all the natural gas can be economically recovered and utilized, in actual practice a large part of the total volume that reaches the mouth of the well is wantonly blown into the air and wasted. It is thus estimated that in the United States only some 25 per cent of the petroleum stored underground in proven fields is actually brought to the surface; and in actual practice close to 25 per cent of the total gas produced is now absolutely wasted. And the dissipation of this

Jan 1, 1936

By V. R. Garfias, R. V. Whetzel

It has been repeatedly questioned whether estimates of oil reserves are of any practical value, as the greater number of such calculations previously made have subsequently been proved to be grossly inaccurate. But even admitting partial justification for such statements, it must be evident that some idea, however approximate, of the available reserves of essential minerals—petroleum included—is of vital importance in mapping their development and the future trend of the related industries, particularly if it is kept constantly in mind that these estimates are not only never intended as a final word but must continually be subject to revision in accordance with the changes in their component factors. The value of these estimates, therefore, hinges on the clear understanding of what is meant by reserves and that the figures can only apply within the limited time when the controlling factors remain unchanged. It should be understood, further, that while estimates of possible and probable oil deposits are as a rule but idle conjectures, appraisals of proven oil reserves can undoubtedly be made with an ever-increasing degree of accuracy. And it is with this in mind that in the present study the endeavor has been to estimate only the world's proven oil reserves and to leave out of consideration the questionable volume of the probable and possible oil reserves. Such a survey presupposes further a clear distinction between the known amount of oil underground in proven fields at any one time, and the proven reserves: the portion that can be economically brought to the surface and made available for utilization. Only a fraction of the petroleum stored underground in proven fields— usually associated with natural gas—is or can be economically brought to the surface, and not all of the oik brought to the surface is economically utilized; also, although practically all the natural gas can be economically recovered and utilized, in actual practice a large part of the total volume that reaches the mouth of the well is wantonly blown into the air and wasted. It is thus estimated that in the United States only some 25 per cent of the petroleum stored underground in proven fields is actually brought to the surface; and in actual practice close to 25 per cent of the total gas produced is now absolutely wasted. And the dissipation of this

Jan 1, 1936

By Charles R. Wraith

The property of the Roan Antelope Copper Mines, Ltd., is situated at Luanshya, north central part of Northern Rhodesia, and is connected with the main line of the Rhodesia Railways, Ltd., by a 24-mile branch line from N'dola. Most of the material and supplies that are not available in Africa are shipped into the country via Beira, on the East Coast of Africa, a distance of 1473 miles from Luanshya and the nearest ocean port. The output of copper is shipped by rail to Beira and thence by boat to the market. Passenger travel is mostly via Cape Town, a distance of 2162 miles from Luanshya. Excellent passenger trains operate on regular schedules between Cape Town and Northern Rhodesia. Luanshya is 13" south of the equator at an elevation of 4000 ft. above sea level, and has a mild healthful climate. During the rainy season, from October to March, the rainfall averages 53 in. The area is profusely covered with vegetation. An ample supply of water for industrial and domestic purposes is available throughout the year. The more important supplies for smelting purposcs, such as wood, coal, limestone, silica, quartzite, and clay for "dolly" mud, are conveniently available. Excellent grades of coal, coke and firebrick are obtained from the Wankie Colliery Co., Ltd., Southern Rhodesia. The Wankie colliery has just completed the erection of equipment for the manufacture of silica brick. An ample supply of quartzite of good grade is available for this purpose. Silica brick is also obtained from the Belgian Congo and from India. Limestone is quarried from a large deposit a few miles from Bwana Mkubwa, which is 30 miles by rail from the smelter. An abundant supply of clay for " dolly " mud and for lining launders is available within a short distance of the smelter. Metallurgy Copper is contained in the ore as chalcocite, chalcopyrite and bornite. Chalcocite predominates in the eastern end of the orebody almost to the exclusion of other copper minerals. The amount of chalcocite decreases with a corresponding increase of chalcopyrite and bornite toward the western extension, where the latter predominate.

Jan 1, 1934

US 4,132,635 -In the froth flotation beneficiation of low- grade siliceous iron oxide ore, an aqueous pulp of undeslimed ore is conditioned first with a reagent formed by incorporating a water-soluble polyvalent metal salt into an aqueous solution of sodium silicate and then with oleic acid or other anionic collector and optionally pine 011 or other frother. The conditioned pulp is subjected to flotation to concentrate Iron oxide values in the froth D. C. Yang, assigned to Michigan Technological University Jan 2, 1979 7 pp (209-1 66) Filed 1-1 3-77 (759,094) Drawing below.) [ ] US 4,133,038-In the froth flotation beneficiation of copper sulfide ore or other ores, an aqueous suspension of a mineral sample of uniform grain size and composition is conditioned with a strongly adsorbable collector in an amount which is a fraction of the amount sufficient to create a monomolecular layer on the mineral grains, and the conditioning continued until the entire amount of collector is adsorbed The conditioned pulp is subjected to flotation, the floated particles separated at timed intervals, and the flotation rate coefficient determined. By varying the degree of adsorption in repeated treatments, the dependence of the flotation rate coefficient on the degree of adsorption may be determined A Nieml Jan 2, 1979 10 pp (364-502) Filed 12-7-77 (858,353) Priority Finland, 5-26-75 (75/1,525) Same: British 1,533,723, dated Nov 29, 1978 Same Canadian 1,065,066, dated Oct 23, 1979 US 4,133,746System and method for maintaining substantially steady state conditions in the froth flotation beneficiation of copper ore, molybdenum ore, or other metal ores The mass flow of flotation concentrate from the cell is monitored continuously, and the rate of admission of aeration air into the pulp in the cell is varied inversely with respect to variations in the mass flow control of rougher flotation cells is accomplished with a single valve G W Dopson, assigned to Magma Copper Co Jan 9, 1979 6 pp (209-1) Filed 11- 23-76 (744,306

Jan 1, 1980

By Harry H. Power

While the attention of all engineering branches is focused today on changes and improvements in the several curricula, we are concerned here with the many questions arising in industry and college concerning the preparation for the petroleum engineering profession. The succession of problems confronting the petroleum engineer demands a degree of versatility not ordinarily encountered in other professions. As a consequence, the student cannot acquire mastery of all the several engineering branches represented in field practice, and as an alternative, he has learned to appreciate the value of thorough training in the basic or fundamental sciences as a Preliminary foundation for professional work. While our attention is directed primarily to the training of engineers in educational institutions, it is necessary that the ultimate education of the professional engineer be kept in mind. It is apparent that his success as an engineer is limited not only by his educational and job experience, but by his native endowments: mentality, Personality and health. The engineer's lack of job experiences often proves as much a handicap as the lack of adequate college training. If the final product proves to be satisfactory, both industry and technical institutions are to be congratulated. However, if the Product is found wanting, the one most responsible should For the most part, students of engineering colleges have had their interests in applied science awakened at a relatively early age. Manyof them entered college as a convenient means of acquiring a technical education, but undoubtedly would have had better prospects in a shorter program offered by institutions of non-college grade. The activating motive of practical interest is also strong in students suitable for college training, but in many cases an intellectual interest must be awakened in order that it may survive graduation. Numerous engineers believe that this progressive process of selection and determination of career aims is one of the essential services rendered by the engineering colleges. Industrialists, who are more inter. ested in quality than quantity of petroleum engineering graduates, have pointed out the good that should result if more emphasis were given to the work of eliminating the misfits. They also point out the protective measures that have been taken by other professions for the betterment of professional standards. Mention has been ,de of the beneficial results to be obtdned by collective determination of the market for the products of engineering schools, particularly in that the students unsuited to the profession would have an opportunity to prepare themselves for employment more suited to their personalities and other qualifications. In the event that such a system of coordinated personnel direction is developed by the

Jan 1, 1941

By Harry H. Power

While the attention of all engineering branches is focused today on changes and improvements in the several curricula, we are concerned here with the many questions arising in industry and college concerning the preparation for the petroleum engineering profession. The succession of problems confronting the petroleum engineer demands a degree of versatility not ordinarily encountered in other professions. As a consequence, the student cannot acquire mastery of all the several engineering branches represented in field practice, and as an alternative, he has learned to appreciate the value of thorough training in the basic or fundamental sciences as a Preliminary foundation for professional work. While our attention is directed primarily to the training of engineers in educational institutions, it is necessary that the ultimate education of the professional engineer be kept in mind. It is apparent that his success as an engineer is limited not only by his educational and job experience, but by his native endowments: mentality, Personality and health. The engineer's lack of job experiences often proves as much a handicap as the lack of adequate college training. If the final product proves to be satisfactory, both industry and technical institutions are to be congratulated. However, if the Product is found wanting, the one most responsible should For the most part, students of engineering colleges have had their interests in applied science awakened at a relatively early age. Manyof them entered college as a convenient means of acquiring a technical education, but undoubtedly would have had better prospects in a shorter program offered by institutions of non-college grade. The activating motive of practical interest is also strong in students suitable for college training, but in many cases an intellectual interest must be awakened in order that it may survive graduation. Numerous engineers believe that this progressive process of selection and determination of career aims is one of the essential services rendered by the engineering colleges. Industrialists, who are more inter. ested in quality than quantity of petroleum engineering graduates, have pointed out the good that should result if more emphasis were given to the work of eliminating the misfits. They also point out the protective measures that have been taken by other professions for the betterment of professional standards. Mention has been ,de of the beneficial results to be obtdned by collective determination of the market for the products of engineering schools, particularly in that the students unsuited to the profession would have an opportunity to prepare themselves for employment more suited to their personalities and other qualifications. In the event that such a system of coordinated personnel direction is developed by the

Jan 1, 1941

By Harry H. Power

WHILE the attention of all engineering branches is focused today on changes and improvements in the several curricula, we are concerned here with the many questions arising in industry and college concerning the preparation for the petroleum engineering profession. The succession of problems confronting the petroleum engineer demands a degree of versatility not ordinarily encountered in other professions. As a consequence, the student cannot acquire mastery of all the several engineering branches represented in field practice, and as an alternative, he has learned to appreciate the value of thorough training in the basic or fundamental sciences as a preliminary foundation for professional work. While our attention is directed primarily to the training of engineers in educational institutions, it is necessary that the ultimate education of the professional engineer be kept in mind. It is apparent that his success as an engineer is limited not only by his educational and job experience, but by his native endowments: mentality, personality and health. The engineer's lack of job experiences often proves as much a handicap as the lack of adequate college training. If the final product proves to be satisfactory, both industry and technical institutions are to be congratulated. However, if the product is found wanting, the one most responsible should be apprehended. FITNESS FOR PROFESSION For the most part, students of engineering colleges have had their interests in applied science awakened at a relatively early age. Many of them entered college as a convenient means of acquiring a technical education, but undoubtedly would have had better prospects in a shorter program offered by institutions of noncollege grade. The activating motive of practical interest is also strong in students suitable for college training, but in many cases an intellectual interest must be awakened in order that it may survive graduation. Numerous engineers believe that this progressive process of selection and determination of career aims is one of the essential services rendered by the engineering colleges. Industrialists, who are more interested in quality than quantity of petroleum engineering graduates, have pointed out the good that should result if more emphasis were given to the work of eliminating the misfits. They also point out the protective measures that have been taken by other professions for the betterment of professional standards. Mention has been made of the beneficial results to be obtained by collective determination of the market for the products of engineering schools, particularly in that the students unsuited to the profession would have an opportunity to prepare themselves for employment more suited to their personalities and other qualifications. In the event that such a system of coordinated personnel direction is developed by the

Jan 1, 1941

By J. B. Dorsey, T. W. Brinkley

Performance of a high-pressure, vaporizing gas-drive project in a volatile oil reservoir is discussed. The project has been in operation for over 8 years. Present recovery from the over-all displaced portion of the reservoir is 40 percent, and an ultimate recovery of 60 percent is indicated. Calculations reflect an over-all displacement volume of 50 percent for the entire reservoir; therefore, ultimate oil recovery will be 30 percent of the entire reservoir oil originally in place. Laboratory vaporization tests conducted prior to project initiation also are presented and discussed, along with an analytical method of determining stock-tank oil production and gar injection requirements related to over-all volumetric displacement efficiency from these data. Introduction The Shoats Creek field is located in Beauregard Parish, La., in the extreme western part of the state (Fig. 1). Discovered in 1956, the field is productive in three Cockfield sand zones, ranging in depth from 8,000 to 9.000 ft. The upper two zones, 1st and 2nd Cockfield, are condensate-bearing gas reservoirs. The lowest zone, the 5th Cockfield, is a volatile-oil reservoir. Laboratory work conducted on crude oil from the 5th Cockfield zone shortly after field discovery demonstrated that, when contacted with dry gas, signidcant volumes of the oil could be vaporized at reservoir temperature and at an appropriately high reservoir pressure. Further study led to the conclusion that early initiation of a crude vaporization project in the 5th Cockfield zone would be superior economically to other methods of reservoir depletion. Consequently, the zone was unitized and gas injection operations started late in 1958. This paper discusses laboratory work performed in conjunction with the project, and project performance to the present. History of Development The 5th Cockfield zone in Shoats Creek is composed of a thin, very shaly, low-permeability sandstone. Oil accumulation is controlled by a structural trap bounded by faults along the north and west and by a water contact on the southern boundary (Fig. 2). The zone covers a productive area of 1,550 acres at an average depth of 9,000 ft. The net sand section is thin, having a maximum thickness of 10 ft and an average thickness of 5.5 ft (Fig. 3). Average reservoir rock properties, as determined from core analysis are presented in Table 1. Shaliness of the zone is illustrated by the typical electric log of the 5th Cockfield section in Fig. 4. Because of the thinness and poor quality of the sand, the 5th Cockfield was developed on a wide spacing. Eleven completions were made in the zone between 1956 and 1961 for an average density of 140 productive acres per completion, with the majority of wells being dually completed in the 2nd and 5th Cockfield. Average initial potential for producers in the 5th Cockfield was 130 BOPD. Oil from the 5th Cockfield has a stock-tank gravity of 50.5" API; with a bubble-point pressure of 3,515 psia, the oil was highly undersaturated at the original reservoir pressure of 4,675 psia. Pertinent properties of the oil as determined in the laboratory are presented in Table 2. Because of the volatile nature of the crude, laboratory studies of its susceptibility to vaporization, as well as a vapor-liquid phase study, were conducted in addition to a standard PVT analysis. The vaporization study was conducted in a visual cell; a stepwise illustration of this work and laboratory measurements are presented in Fig. 5. Field

Jan 1, 1969

By W. B. Wise, H. D. Attra, W. M. Black

The purpose of this paper is to illustrate a comparatively new approach for solving a problem that has plagued oil producers for many years—how to make the most money with available field production capacity. In a very basic operation such as a top-allowable one-well field, a computer and staff of engineers are not required to determine that the best operation is to produce that well at its maximum for as long a time as it will produce. However, as the problem becomes more complex and the number of wells and number of reservoirs increase, it probably will be a wise choice to devote some engineering thought and calculation time to determine the best way to operate that field on both an ultimate and day-to-day basis. Continued developments in the field broadly referred to as "operations research" have led to a number of useful engineering analyses for optimizing field operational problems. One of these techniques, termed linear programing, is parlicularly interesting because of its potential applications to the study of complex oilfield operating problems. Linear programing is concerned with the problem of planning a complex set of interde~endenl activities in the best possible (optimal) fashion. A field application of linear programing is being used to maximize daily income from a multi-reservoir producing operation. The initial results of this study indicate that the linear programing technique (I) can be applied effectively to field problems, (2) can be used to detect unsuspected avenues for improving operations and (3) can effect a significantly improved means of controlling field operations through the use of the highspeed computer. INTRODUCTION The usual approach for studying complex field operational problems has been to look in detail at several basic plans suggested by judgement and experience and, then, to choose the best plan from those investigated. This approach is entirely satisfactory provided: (1) that judgment and experience alone will reliably pick the best or near the best program as one of the plans to be investigated; and (2), and most important, that the factors which control field production will not change. This paper deals with the large group of field operations which are at least one-step removed from a satisfactory solution using the conventional method of analysis. Problems such as pipeline- and gathering-system design, transportation studies, large field development projects and multi-reservoir producing operations fall in this latter category. To find the best program for handling these problems when the best program is not obvious, a complete optimization study is required, and high-speed computers are required to continually update the program once it is selected. Operations of this type have an extremely large number of possible solutions. However, only one will result in maximum economic return and, more important, this one program must be re-evaluated and adjusted constantly to accomodate such changing field factors as the number of producing days, the price of crude, the discovery of new reserves, declining reservoir pressure with subsequent decline in production and a host of other factors which characterize specific operations. One of the most widely used, direct methods of optimization is a numerical procedure termed "linear programing", which is designed to investigate systematically each of the possible solutions involved in a given problem, determining rapidly and uniquely the optimum answer. As implied by the name, linear programing requires that all field variables be either defined or expressed in a series of interdependent linear equalities or inequalities. These relationships are solved simultaneously, using a form of matrix solutions to determine the optimum values for each producing variable that will maximize net profits. The solution techniques used in a recent field case study is termed the "simplex method" and is discussed in full detail in Ref. 1.

By John T. Schamaun

Recent applications of explosives and blasting agents to rubble rock have led to requirements for more elaborate design and analysis methods. In most blasting uses, it is necessary not only to fracture the rock, but also to move the broken rubble in a predictable manner. Many in situ extraction techniques require rubblization to take place in a confined region where rock motion is a predominate factor in creating a permeable broken bed. In this paper, two analytical methods are presented which describe the large rubble motion during blasting. These methods provide the blast designer with a tool for evaluation and further refinement of blasting patterns and timing sequences. In both these methods, the rock medium is represented by a series of discrete, discontinuous regions. The use of discontinuous techniques rather than the classical continuum methods, results in better approximations to the rubble motion. These regions are set in motion by pressure loads from the explosive. The motion of these regions is then calculated numerically using interaction laws between regions in contact. The basis for these models or methods is presented along with the background for selecting explosive pressure loads and rock mass material behavior. Typical examples, including both cratering and bench blasting geometries, are discussed which illustrate the use of these models to predict rubble motion. Such engineering representations appear to provide a practical method for use in predicting rubble motion and a tool for design evaluation of blasting in confined geometries.

Jan 1, 1984

By G. M. Yocom

Blowing acid Bessemer converters with oxygen-steam produces steel of below 0.002 pct N2 content. This method of blowing, combined with a dephosphorizing treatment in the steel ladle, results in low-carbon steels of low nitrogen and low phosphorous (under 0.035 pet) contents, which has physical properties equivalent to open-hearth steels of similar analysis. Using a 50-50 mixture of oxygen and steam, the refinitzg rate is increased 25 pct over blowing with natural air, and scrap charge increased from 3 to 10 pet. Bottom life is normal with proper tuyere area and arrangements, fumes are decreased, yields increased, and hydrogen content is normal. THE acid Bessemer plant at the South Works of Wheeling Steel Corp., consists of two 15-ton bottom blown converters with a monthly capacity of 57,000 N.T. The product of the shop is skelp billets for continuous welded pipe and slabs for ordinary drawing and forming quality sheets. Approximately 50 pct of ingot production is regular Bessemer steel of natural Phos content and the remainder is a dephosphorized grade of steel made by a special treatment of the blown metal as it is poured into the steel ladle. The low Phos grade of steel has certain advantages over the higher Phos grade but since both grades were produced by blowing natural air, the N2 content was in the range of 0.015 pct which limited its application. In 1954 it was decided to explore the possibilities of blowing with a steam-oxygen mixture for the production of steel of both low N2 and low Phos contents. The necessary equipment was installed to operate one converter in this manner and early in 1955 an experimental run of 160 heats was made by blowing with a steam-oxygen blast and excluding natural air entirely. During this period the proper operating techniques were established, such as blast pressures, steam-oxygen mixtures, valves and instrumental control equipment, tuyere arrangement in the bottoms, blowing times and production rates, and a thorough study made of the final steel quality. Also during this experimental period the dephosphorizing practice was improved by the use of a tap hole below the lip of the vessel. This provided a clean separation of the acid converter slag and blown metal which made the dephosphorizing treatment more effective. The results of this experimental run dictated further development of this practice and a second run of 720 heats was made in 1957. The quality features and conversion cost results were in line with expectations and accordingly a 400-ton per day oxygen plant is now being installed. The plant is scheduled for completion in September of this year. This will provide sufficient oxygen to operate both vessels on steam-oxygen blast and delete natural air blowing entirely. The steel will then be below 0.002 pct N2 bar content and the dephosphorized grades will be between 0.015 and 0.040 pct Phos. STEAM-OXYGEN BLOWING The steam for the process is fed to the plant at 220 psig pressure through a 6-in. line. The high-purity oxygen is compressed to 200 psig and conducted through an 8-in. line. The oxygen from the main line is valved down to 100 psig and passed through a steam heated heat exchanger. The heat exchanger is regulated to supply oxygen at 300°F to the steam-oxygen mixing station. It is essential that the incoming oxygen be held at this temperature to avoid condensation of the steam with resulting excessive erosion of the clay tuyeres in the vessel bottom. Oxygen is admitted to the mixing chamber by a 6-in. hydraulically operated valve driven by the ratio control regulator on impulse from the flow of steam. Steam is admitted to the steam-oxygen mixture station through a 2 1/2-in. hydraulically driven valve. The ratio control regulator acts to increase or decrease oxygen input as the steam flow increases or decreases with changing positions of the Blower's control lever. The important point to note here is that steam flow always precedes the oxygen flow as a safety measure. The control valves have sufficient capacity to afford protection should blow pipe trouble develop. A 50-50 mixture for these 15-ton heats demands an oxygen flow of 3800 standard cu ft per min along with 317 lb of steam. The Blower's stations is provided with an indicating blast pressure gage, and indicating steam and oxygen flow meters. Signal and warning lights indicate the valve positions and line pressures. A control room at the real of the Blower's pulpit room houses the ratio control and pressure regulators, as well as the various meter bodies. The hand actuated wheels used to change the conditions are mounted on a panel on the front of the meter control house. The recording steam and oxygen meters used for totalizing and accounting purposes are also mounted on this panel.

Jan 1, 1962

By D. Atkinson, C. Bodsworth, I. M. Davidson

A geometric model of interstitial solid solutions, which has been used previously as a basis for the prediction of carbon activities in Fe-C austenite, is shown to serve also for the calculation of nitrogen activities in Fe-N austenite. The model has been developed to enable predictions to be made of the activities of an interstitial element in the presence of two host atom species. The activities calculated via the model are shown to be in satisfactory agreement with the measured values in the austenite phase for carbon in Fe-C-Co, Fe-C-Cr, Fe-C-Ni, Fe-C-~n, Fe-C-Si, and Fe-C-V alloys and for nitrogen in Fe-N-Ni alloys. The effect of the second substitu-tional solute on the logarithm of the activity of the interstitial element is expressed as the product of a constant mad the atomic concentration of that solute. The constants so derived we related to the thermo-dynamic interaction coefficients which describe the effect on the activity coefficient of carbon of an added solute element. In recent years the thermodynamic activities of carbon and nitrogen in the single-phase austenite field have been determined for iron binary alloys and for several iron-base ternary alloys. In order to extend the use of these measurements, it is desirable to be able to predict with reasonable accuracy the activities of the interstitials at compositions and temperatures other than those which have been measured experimentally. In all the systems studied to date, the interstitial elements do not conform to ideal behavior. Hence, the available data cannot be extrapolated or interpolated using the simple thermodynamic concepts of solutions. Several models have, therefore, been formulated for the purpose of predicting the activity of an interstitial element in the presence of one species of host atom. These models can be divided into the geometric1"5 and energetic6-' types. The former group is based on the assumption that at low concentrations the activity of the interstitial species is determined by a composition-dependent configurational entropy term and an excess free-energy term which is temperature-dependent but independent of composition. The purpose of this paper is to show that the treatment, based on a geometric model, can be extended to enable predictions to be made of interstitial activities in the presence of two substitutional host atom species. THE CONFIGURATIONAL ENTROPY OF MIXING ICaufman5 has shown that the configurational entropy, S,, for a binary solution comprising of a host atom species, A, and an interstitial species, I, can be expressed as: where NI is the atom fraction of the interstitial species, R is the gas constant, and (2 - 1) is the number of interstitial sites excluded from occupancy by the strain field around each added interstitial atom. The number of interstitial sites per host atom, p, is unityg for the fcc austenite solutions considered here. The configurational entropy of mixing for a ternary solution comprising two substitutional atom species, A and B, and one interstitial species, I, can be derived similarly. Let the number of atoms per mole of each of these species in the solution be represented by «a, ng, and nI. From geometric considerations, it is improbable that the addition of a few atom percent of a second host atom species will change the type of sites (i.e., octahedral) in which the interstitial atom can be accommodated in the austenite lattice. At higher concentrations (determined largely by the relative atomic radii of the atomic species present and any tendency to nonrandom occupancy of the host lattice sites) other types of interstitial sites may become energetically favorable. Restricting consideration to compositions below this limit, for 1 = 1 the number of suitable interstitial sites is given by (n + nB). However, if each interstitial atom excludes from occupancy (Z - 1) additional sites, the total number of sites available for occupation is reduced to (n + ng)/Z. The number of vacant interstitial sites is given by: The total number of recognizable permutations of the atoms must include the recognizable, different configurations of the A and B atoms on the host lattice. Assuming that these arrangements are purely random, and are not affected by the presence of the interstitial species, the total number of recognizable permutations in the ternary alloy is given by: The configurational entropy is obtained by expanding, using Stirling's approximation, and collecting like items, as:

Jan 1, 1969

By H. E. Nold

THIS paper is an effort to explain in a simple manner the fundamental principles involved in examining a clay deposit for both quantity and quality and in operating a clay mine, either open-pit or underground, so that the best quality of finished material can be made from the raw material available. The writer is aware that what is recommended in this paper is everyday practice in many refractories plants and in some other heavy-clay products plants, but observations made while visiting practically every clay mine in Ohio have convinced him that the practices herein discussed are not as widely used as their importance warrants. It is true that the problem of mining for quality is more acute in refractories plants than in most heavy-clay products plants, yet some of the latter are finding it profitable to pay more than ordinary attention to the selection and blending of their raw materials. It is hoped that this short paper may prove helpful to some who are now finding it difficult to produce a uniform product of as high quality as their clay deposit seems to warrant. The coordination of the work of the clay mine or pit with the manufacturing plant, to the end that the best product possible be made from the raw material available, presupposes a rather intimate knowledge of the clay deposit. The knowledge must include not only information of the amount of clay-available but also rather detailed information about both vertical and horizontal variations in quality of the clay. This information should cover three things: quality, quantity, and location.

Jan 1, 1929

By C. Augustus Carlow

THE subject which has been allotted to me is so vast and far-reaching that it is impossible to deal adequately with it in the time available. A complete survey would occupy the spare time of any one man for many years, whereas the time available to me is measured in weeks In the circumstances, I have been fortunate in securing the aid of several willing collaborators, and shall endeavor to re present such information as presently exists in published form, examine the situation critically in the light of present-day conditions, and arrive at certain conclusions' which I shall venture to put forward for your consideration No one who has lived through the past 25 or 30 years, and who has witnessed the amazing achievements of recent scientific research, would venture to deny the possibility that new sources of energy-may yet become available, or to prophesy to what extent these may be harnessed to the service of mankind So far as we can see, however, coal, as a source not only of power and heat but also of that wonderful range of derivatives that form the raw materials of so many industrial processes, must continue to play a vital role in our economic life It is the chief mineral fuel, exceeding all other mineral resources in value, production and demand In value coal overshadows the industrial metals, while of the sources of energy-coal, oil, gas and water power-the first named is the most important Thus, for example, in the United States, coal as a fuel (that is, as a source of heat and power) is still predominant, the figures of percentage of

Jan 1, 1947

By B. H. Cody

The Morenci concentrator of the Phelps Dodge Corporation is a part of the project that was completed after five years had been spent in development of the open-pit mine, equipment and process testing in the former No. 6 concentrator, and construction of the reduction works. The reduction works, of which the concentrator is a part, is about a mile and a quarter southeast of Morenci, on the highway that leads up Morenci Canyon. The concentrator has a nominal capacity for the treatment of 45,000 tons of ore daily. The original plant, which has a rated capacity of 25,000 tons of ore daily and is now in its fifth year of operation, began production on Jan. 30, 1942. The addition, to increase the capacity 80 pct, began operation on Dec. I, 1943. The equipment of the original plant has been described in Mining and Metallurgy (May 1942). NO changes in equipment were recommended for installation in the concentrator extension and only one major change, forced by a shortage of maintenance labor, has since been made. Metallurgical treatment has been altered in some ways as experiments progressed and as labor and economic conditions dictated. No complete description of the operation of the concentrator has been published, so this paper will record such operating and equipment changes as have been necessary, the operating methods that have been developed and the metallurgical results that have been obtained. Descriptions are given in the order of the processes with a flowsheet and an equipment list of each process for convenient reference. The questions asked by engineer visitors have guided the detail in which operation and maintenance are described. During the period Jan. 30, 1942 to Sept. I, 1946, ore milled has totaled 43,595,253 dry tons, from which 1,643,885 tons of concentrate have been made, containing an indicated production of 783,164,-809 lb of copper. The principal results obtained in operation of the concentrator during the years 1942 to 1945, inclusive, and to Sept. I, 1946 are shown in Table I. A graphic general flowsheet of the plant is given in Fig I. Ore The Morenci ore that is now being treated is a medium-hard monzonite porphyry in which the principal sulphide minerals are chalcocite and pyrite. A minor amount of covellite is present. Chalcopyrite and bornite have been observed under the microscope. The chalcocite occurs mainly as a coating on pyrite. Some of the coatings are so thick that the pyrite presents the appearance of being an inclusion in chalcocite. Some are less than one micron thick and are barely visible at 500 diameters magnification of a polished cross section. Some chalcocite is present as a in in the gangue. Various oxidized copper minerals are present as a result of oxidation in place but they represent a minor proportion of the copper minerals of the ore body. Oxidation

Jan 1, 1949

By James Elton

THIS paper covers, besides laboratory work, a study of actual operation at the Washoe Smelter over a considerable period of time, together with the results of a visit to the Midvale plant of the United States Smelting- & Refining Co., near Salt Lake. For the latter privilege, as well as permission to publish the resulting data herein given, I am indebted to George W. Heintz, General Manager of the Midvale plant, and here take pleasure in. expressing my appreciation for the many courtesies extended to me by Mr. Heintz and members of the technical staff at the smelter. Almost all of the world's supply of arsenic is recovered as a by-product in the smelting of other metals. It is seen on the market in various forms, the most common being arsenic trioxide, the ? white arsenic " of commerce, which is sold as a heavy white powder, or in white, glassy, translucent masses. The trioxide is used in the manufacture of pigment, glass, and insecticides. About 50 per cent. of the domestic consumption is supplied by imports.

Jan 8, 1913

By Mark S. Childs

FRIEDENSVILLE orebody in Lehigh County, Pennsylvania, lies in the south central part of the USGS Allentown Quadrangle. Physiographically the area is located in a small reentrant-known as Saucon Valley-of the Great Valley Province into the Reading Prong of the New England uplift. Saucon Valley itself is an oval-shaped lowland eight miles long and four miles wide, surrounded by ridges except where connected with the Great Valley through a breach in the rim known as Saucon Gap. These ridges, composed of Pre-Cambrian metamorphic rocks and Cambrian quartzites, rise some 500 ft above the valley floor. They are continuous with the New Jersey Highlands. The valley lowland is immediately underlain by lower Paleozoic dolomites and limestones. This area is one of low relief having a swing of approximately 100 ft, with an average elevation of 375 ft above sea level. The entire valley, which has a water shed of about 58 sq miles, is drained by Saucon Creek. This unit flows in a northeasterly direction to the Saucon Gap, where it discharges into the Lehigh River.

Jan 1, 1957

By S. F. Shaw

The theory that maintaining a high back-pressure on the oil sand lowers the viscosity of the oil has been generally accepted. The theory has also been advanced that lower viscosity permits the oil to be moved through the sand to the well at an expenditure of less gas per barrel of oil than would otherwise be required. It seems reasonable to assume that production of oil at the minimum gas-oil ratio will result in a greater ultimate recovery of oil. During the past five years the writer has acquired data on thousands of tests made on wells to determine the best rate at which to produce them. In the majority of cases reduction in back-pressure did not definitely increase the gas-oil ratio. The information obtained from these tests has raised doubt in the mind of the writer as to the correctness of the theory that lowered viscosity results in lower gas-oil ratios and in higher ultimate recovery of oil. The reasons that explain the results obtained in these tests cannot yet be definitely stated, but the hypothesis is being tentatively assumed that there are other factors which outweigh the influence of viscosity. Energy in Gas Moves Oil to Well The general opinion is that in most cases it is the energy in the gas that moves the oil to the well. In wells flowing naturally it is also the energy in the gas that lifts the oil to the surface. In a flowing well, there are two very distinct operations: 1. Moving the oil through the sand to the well. 2. Lifting the oil to the surface. The more important function of the gas is that of moving the oil to the well. Means for lifting the oil can always be found once it has been delivered to the well. Principles Involved in Lifting Oil A well that flows naturally is the same as a gas-lift well except that all of the gas is supplied by the oil reservoir. This natural flow is subject

Jan 1, 1931

By Fred D. Rosi

Introduction There is probably no field in which materials research has played a greater role than that of electronics. However, to trace present and future patterns of materials research in electronics is not an easy assignment, since this industry has a high degree of dynamism in its growth, and is busily engaged today in the scientific improbabilities of only recent yesterdays. On the other hand, this task seems especially appropriate since electronics is a truly frontier industry - one whose place in American industries has advanced from 50th prior to World War II to 6th in 1967, with sales of more than $22 billion. And this growth has been associated with the equally rapid progress of science and technology over the period - in particular with the emergence of materials science as a vital force in underscoring this progress. For several reasons this parallel growth is not too surprising. First, by its very definition electronics is a science that essentially deals with the nature, behavior, detection, generation, control and utilization of electrons in solids or at their surfaces. Second, in the electronics industry, systems are made of an integration of components, and these components with their interconnections are made of materials. Thus, the basic building blocks of systems are materials; and it has been largely the advances in materials research and technology that have led to new and improved devices and systems. It follows, therefore, that the broadening of the frontiers in electronics through the exploration of new territories is tantamount to scientific discovery and materials innovation to a degree found in no other major industrial activity. But to put this in the proper perspective of present and future materials trends, it would be appropriate first to survey historically the progress in electronics by pointing out major scientific discoveries and associated materials research patterns that have led directly to its tremendous growth. Then from this base we can consider recent trends in materials research that could form the basis for future progress in the electronics industry. In my review I shall examine the areas most familiar to me, so I must acknowledge at the outset that this survey is not all-inclusive.

Jan 1, 1971

By N. M. Langdon

ON account of its greater economy and cleanliness, and the extent to which iuferior fuels can be utilized for its generation, there has been of late a rapidly increasing tendency to substitute gaseous for solid fuel for metallurgical and other industrial purposes, which has led to various improvements both in the process and apparatus for its manufacture, notably among which may IN mentioned the Tessie Gas Producer* described by Mr. A. L. Holley. A considerable experience by the author with producers of various kinds using anthracite fuel, in connection with the Taylor ore-roast ing furnace at Chester, N. J., with more or less unsatisfactory resnlts, finally led to the erection of the experimental producer described below, which combines in its construction, simplicity, dorability, and accessibility for cleaning and removing the ash and manipulating the fuel. It is adapted to the use of various kinds of fuel, and is capa ble of generating a steady and uniform supply of gas at a minimum cost. It has been in constant use day and night for about five months, and has given very satisfactory results. The producer, as shown in the accompanying sketch, consists of a cylindrieal furnace, preferably inclosed in an iron jacket or casing, having a bosh or inverted cone-shaped base as in a blast furnace. It is provided with a bell and hopper, the bell being hung to a forked lever, and having guide flanges to prevent it from swing ing, and an opening at its apex through which to insert a bar for manipulating the fuel, which when not in use is closed with a plug or stopper. Cleaning is effected through two small doors placed opposite each other at the hearth level, which in order to facilitate the operation is elevated above the floor. The doors are removable, and when closed are by their own weight and by means of bevelled lugs held tightly against their frames, forming a practically tight joint. A blast of commingled steam and air is injected into the fuel through a series of tuyeres underneath the bosh communicating with steam jet injectors. A small flue also connects the door

Jan 1, 1884