Search Documents

By V. Koump, T. F. Perzak, R. H. Tien

A series of experiments were carried out in which the rates of propagation of the liquidus and the eutectic fronts Mere measured during essentially one-dimensional freezing of Al-Cu alloys. The dimensions of the ingots were 3 by 5 by 6 in. Three different alloys containing 0.1, 4.5, and 17 pct Cu were used in these experitments. For each alloy the rate of heat removal was varied to give a total jreezing time in the range 3 to 30 min. The results of these measurements cowlpared favorably with the theoretical model of freezing of binary alloys with time-dependent surface temperature. IN engineering analysis of solidification of commercia1 steels and nonferrous alloys it is a common practice to assume that an alloy freezes by propagation of an isothermal solidification front, i.e., essentially as a pure metal. In two recent theoretical investigations'j2 the present authors explored the possibility of a more realistic approach to the problem of solidification of alloys. In the proposed model the freezing of an alloy is assumed to take place by propagation of two isothermal fronts, i.e., the liquidus front and the solidus (or eutectic) front. The region between the two fronts contains both liquid and solid and is referred to as the solid-liquid region. The width and the solid content of the solid-liquid region vary with alloy type, solute concentration, and cooling rate. For a given alloy system, initial concentration of solute, and the mode of heat removal, the proposed model yields the temperature distribution within the solid skin, temperature, solid fraction, and concentration distributions with the solid-liquid region, and the rates of propagation of the liquidus and the solidus fronts. This model is obviously of considerable practical importance in engineering analysis of solidification processes, since it gives a more realistic estimate of skin strength during solidification and a better estimate of the total freezing time. Before the new model can be used with confidence, however, it is necessary to test this model experimentally. The experimental testing of the proposed model is a relatively simple matter since the effects to be measured are large and a relatively simple experiment will suffice. The theoretical model predicts, for example, that during freezing of an alloy containing substitutional type solute (negligible diffusion in the solid during freezing) the solid-liquid region occupies an appreciable portion of the ingot, even at low concentration of solute.' Another prediction of the theo- V. KOUMP, formerly with U. S. Steel Corp., is now with Research and Development Center, Systems and Process Division, Westinghouse Electric Corp., Pittsburgh, Pa. R. H. TlEN is Senior Scientist, Fundamental Research Laboratory, U. S. Steel Corp., Research Center, Monroe ville, Pa. T. F. PERZAK, formerly with U.S. Steel Corp., is now with Fiber Industries, Greenville, S. C. Manuscript submitted March 6, 1968. IMD retical model, easily verifiable by experiment, is that the rate of propagation of the solidus (or eutectic) front increases as the solidus front approaches the center of the slab. This prediction is contrary to well-known behavior of the solidification front during freezing of pure metals, where the rate of propagation of the solidification front decreases with time and freezing is completed at the lowest rate. A rather severe test of the proposed model is provided by comparison of theoretical predictions and experimental measurements of the effects of cooling rate and composition on the rates of propagation of the liquidus and the eutectic fronts. In order to test the soundness of the formulation and the method of solution of the problem of solidification of alloys a series of experiments were carried out in which the rates of propagation of the liquidus and the eutectic fronts were measured during essentially one-dimensional solidification of A1-Cu alloys. The A1-Cu system was chosen strictly as a matter of convenience. Three different alloys containing 0.1, 4.5, and 17 pct Cu were used in these experiments. For each alloy the rate of heat removal was varied to give the total freezing time in the range 3 to 30 min. The results of these measurements are compared with the predictions of the theoretical model of solidification of binary alloys, with time-dependent surface temperature.' Before the experiments described in this paper were undertaken, a serious attempt was made to utilize the measurements of previous investigators to test the theoretical model. In the course of this preliminary study a careful review was made of experiments of Pellini and coworkers3 and Doherty and Melf~rd.~ The measurements in Pellini's work were carried out using a steel containing at least four major components. Evaluation of the solid fraction-temperature relation for this steel (required in the theoretical model) is difficult and uncertain. Doherty and Melford, on the other hand, measured the solid fraction-temperature relation experimentally, but did not give sufficient data to explore the effects of composition and the cooling rates on solidification. Hence it was not possible to utilize these measurements to test our theoretical model. EXPERIMENTAL METHOD The experimental technique used in this investigation differs somewhat from the more conventional techniques employed in solidification studies. This technique was developed primarily to eliminate con-vective mixing in the molten metal caused by pouring of molten metal into the mold. In our experiments A1-Cu alloys were melted directly in the mold. The mold assembly used in solidification experiments is shown in Fig. 1. The mold was fabricated from *-in. stainless-steel sheet. The dimensions of

Jan 1, 1969

By F. B. Foley

IT is with an unusual degree of personal satisfaction that I find myself in a position to pay tribute to the memory of Henry Marion Howe. One could not have spent any length of time in the presence of Dr. Howe without profiting intellectually. I do not hesitate to say that my years of association with him were the most stimulating of all my years of metallurgical study. He always impressed one with his own eager search for knowledge. Never dependent on the written word alone he sought information from anyone whose opinion he valued. His ability to piece together bits of apparently conflicting data from various sources so as to build up a logical hypothesis was unique. A small slight man with the intellect of genius he would have gone to the top in any endeavor he undertook and it was fortunate for metallurgy that its study attracted him as it did. Howe was a modest man. I like to recall an incident which left a lasting impression with me. The lab- oratory in his home, "Green Peace," was in the basement and access was by way of stairs leading down from his secretary's room. In using these stairs my attention was attracted many times to an ordinary cardboard shoe box which reposed on the shelf above the landing. It was crudely labeled on its side in black ink "Vanity Box." My curiosity was aroused to the point that I finally asked his secretary what it was. With some amusement she took the box from its shelf on the stairway, opened it and showed me its contents—numerous letters, from the foremost men of science of every civilized country throughout the world, commending his "Metallography of Steel and Cast Iron." I recall that in reply to one who thought there was not enough of Howe's own researches in his book he wrote, "Primarily I am a writer, secondarily an investigator." Howe wrote to make his readers think. No one ever strove harder than he to be right but above all, whether his viewpoint proved ultimately to be right or wrong, he was always content if by his stand, he provoked a reader to take the next step along the path to greater knowledge. I doubt that he was ever afraid to be wrong for he was always secure in the thought that his effort was guided by a sincere search for the truth. One continually searching for truth is entitled to occasional excursions up the wrong alley. A glance backward to the metallurgical confusion of some thirty to forty years ago, or need one go back so far, provides convincing proof of what a host of companions one may have in a common acceptance of ideas which the future will prove to be wholly untenable. Well over a hundred years have passed since investigators have interested themselves in the effect of increasing the temperature of iron and steel on their mechanical properties. We are told by Charles Walrandl in "Industrial Annals" for June 11, 1822, that bend tests, conducted in a Russian steel works of Prince Demidoff, on steel bars "highly heated" and bent during cooling became brittle when bent at an iris blue color. He concluded, "That when steel is heated to a temperature between 473°F and 662°F the mettle was more brittle between these limits than at a much lower or at a much higher temperature." It was a curious bit of information recognized as true to this day and still not explained satisfactorily. In 1878 Charles Houston in Annales de Mines associated this brittleness with an increase in tensile strength at 572°F. When this relatively low temperature is exceeded it is recognized that steel becomes weaker as temperature is increased up to the melting point, where no strength of practical importance remains. It is easy to believe, in fact it goes without saying, that this weakening as the temperature of a metal is increased is the result of the motion of the atoms making up the metal, a motion which itself is evidence of the temperature increase. However, if we are considering iron or steel we find that this decrease in strength is not a steady one, for, besides the increase in strength just referred to, one comes to a temperature, the critical temperature, where results of tests indicate the metal to be extremely weak and then as temperature increases to become sensibly stronger again. This apparent anomaly was made the subject of the first Howe Memorial Lecture, delivered by Albert Sauveur in 1924. It may be of interest to review these findings of Sauveur. He used two methods of investigation. One involved the twisting of bars. The bars were heated in an

Jan 1, 1951

By P. M. Aziz, I. Markson, C. S. Barrett

The abnormal after-effect in twisted wires that occurs when untwisting is interrupted by etching con be brought under control and used to study the mechanical properties of thin surface films and how they are effected by reagents and heat treatment. Results are given of studies of oxide films on high purity aluminum. IF a wire is subjected to plastic deformation by torsion and then released, it untwists in the normal after-effect, but under certain circumstances the untwisting is abruptly lessened or reversed by the application of an etchant to the wire.1,2 This abnormal after-effect may occur, for example, if there is a coherent oxide film on the surface of the wire which is removed by the etchant. Following a suggestion of A. H. Cottrell that predicted this effect, it is attributed to dislocations that had piled up beneath the oxide layer and represents the rapid release of residual stresses caused by these dislocations. When the layer is removed, the stress relief may be by escape of piled-up dislocations from the metal, or by an activation of latent sources of dislocations located at the surface, together with rebalancing of elastic stresses to compensate for the loss of stressed material, as in a residual stress analysis determination, these mechanisms acting singly or in combination.' The slower the attack of the reagent, the more gradual is the stress relief and the smaller the change in strain rate when the reagent is applied. A study has been made of the factors that influence the magnitude of the normal and abnormal after-effects with the object of developing techniques suitable for a quantitative investigation of the influence of various surface films on dislocations in wires, and of the rate and extent of the attack on the films by different reagents. It was found that reasonable sensitivity and reproducibility could be achieved if a suitable choice of variables was made and if these variables were held constant through a series of experiments. The method was then applied to a study of oxide films produced and treated in different ways on the surface of high purity aluminum wires, and to a study of the damage to these films caused by various reagents. Experimental Procedure The material used throughout this work was prepared from 99.9968 pct Al. This high purity aluminum was melted, cast into 1/2 in. diameter ingots, and then swaged and drawn without intermediate annealing to 0.040 in. diameter wire. A sketch of the apparatus employed for twisting is shown in Fig. 1. The test wires were mounted into the apparatus by cementing one end of the wire to the beaker and the other to the tube with laboratory wax of high melting point. The length of the wire between the waxed joints was 4.2 & 0.2 cm. Extreme care was taken during mounting to avoid cold-working the wire. The wire was twisted through 335" in 2 to 4 sec by rotating the pinion on the gear box until the vertical post on the rotating table, which was initially touching the horizontal stop, was arrested by the stop. All the tests were conducted with apparatus and reagents at the same temperature (about 25°C). In all tests, except those where the duration of the initial torque was investigated, the torque was applied for a period of 2 min. At the end of this time the table was rotated back a few degrees away from contact with the stop and the wire allowed to untwist. The after-effects were measured by reflecting a beam of light from the mirror shown on the apparatus. After the wire had untwisted for 6 min, a reagent was carefully poured into the beaker and thereby applied to the surface of the wire.. In some tests the liquid in the beaker was removed after a few minutes and replaced by an-

Jan 1, 1954

By E. D. Gardner

Apparently the widespread agitation for the codification of our mining laws has had its effect, and it is quite possible that Congress will take up the question during this present session. The greatest objection to our present statutes pertaining to metalliferous deposits seems to be directed against the law of the apex. Those who are not in favor of changing this law are very far in the minority and they apparently realize that it is useless to urge its retention. Next in importance to the repeal of the law of the apex, seems to be a widespread advocacy for the repeal of the law requiring discovery of mineral before a valid location of a mining claim can be made. To a lesser extent there appears to be a desire to have the law changed so as to allow patent for claims without mineral discoveries. The purpose of this article is to review the arguments in favor of the proposed change of the discovery requirement, to show some of the evils that may be expected to result therefrom, and to consider whether a system may be devised to correct the undesirable features of the present law in this respect and at the same time not expose the mining fraternity and the general public to the evils which would result from the repeal of this fundamental requirement. Under the law as at present framed, the validity of a mining location is dependent upon the fact of discovery of mineral within the boundaries of the land claimed. " * * * but no location of a mining claim shall be made until the discovery of the vein or lode within the limits of the claim located" (Sec. 2,320, U. S. Rev. Stat.). All authorities agree that discovery is the source of the miners' title. Lindley, in his valuable work on Mines (3d Ed., Sec. 335), lays down the rule in part as follows: "Discovery is the initial fact. Without that no right can be acquired. * * * Such discovery must precede the location, or be in advance of intervening rights. The proof of recording and marking a claim will not authorize the court to presume a discovery." As is well stated by the U. S. Supreme Court in Erhard v. Boaro (113 U.S. 536):

Jan 1, 1917

By Ernest Gayford

This is a nontechnical paper on flotation, subdivided under three general headings: (I) Definition of flotation; (2) what flotation is now doing in Utah; and (3) what is the future of flotation? Definition T. A. Rickard defines flotation' as "the act or state of floating," from the French flottaison, water-line and flotter, to float. The dictionary defines flotation as "the science of floating bodies." The flotation process is a method of concentrating ores by frothing. Weinig and Palmer,2 define flotation as follows: What is the flotation process? Briefly, it consists in the agitation of finely divided ore in water containing bubbles of air or gas, a small amount of oil and, usually, other reagents, soluble and insoluble; under these conditions the small particles of native metals, sulfides, arsenides, antimonides, selenides and tellurides show a tendency to attach themselves to the films of the bubbles, and are thus carried to the surface of the water. The oxidized gangue minerals, such as quartz, feldspar, limestone, hematite, etc., show much less affinity for the bubbles, are easily wetted by the water, and either remain in suspension in the water, or sink to the bottom of the vessel. If the bubbles are sufficiently stable they can be removed, carrying their load of sulfide-mineral particles with them. Thus there can be effected a separation of the two classes of minerals from each other, assuming that the grinding has been sufficient to unlock all of the particles of different composition. The separation does not depend upon differences in specific gravity of the various minerals; in fact, the sulfides are usually heavier than the oxides, and some of the heaviest sulfide minerals are the easiest to float. A particle of mineral may be so large, however, that its weight will counteract its affinity for the film of the bubble. In most cases the ore must be fine enough to pass a screen having at least 48 meshes to the linear inch. Taggart3 defines flotation as follows: Flotation is a method of wet concentration of ores in which separation of mineral from gangue is effected by causing the mineral to float at or above the surface of a body of liquid pulp while the gangue becomes or remains submerged. The method

Jan 1, 1928

By Ernest Gayford

THIS is a nontechnical paper on flotation, subdivided under three general headings: (1) Definition of flotation; (2) what flotation is now doing in Utah; and (3) what is the future of flotation? . DEFINITION T. A. Rickard defines flotation1 as "the act or state of floating," from the French flottaison, water-line and fitter, to float. The dictionary defines flotation as "the science of floating bodies." The flotation process is a method of concentrating ores by frothing. Weinig and Palmer 2 define flotation as follows: What is the flotation process? Briefly, it consists in the agitation of finely divided ore in water containing bubbles of air or gas, a small amount of oil and, usually, other reagents, soluble and insoluble; under these conditions the small parti- cles of native metals, sulfides, arsenides, antimonides, selenides and tellurides show a tendency to attach themselves to the 6lms of the bubbles, and are thus carried to the surface of the water. The oxidized gangue minerals, such as quartz, feldspar, limestone, hematite, etc., show much less affinity for the bubbles, are easily wetted by the water, and either remain in suspension in the water, or sink to the bottom of the vessel. If the bubbles are sufficiently stable they can be removed, carrying their load of sulfide-mineral particles with them. Thus there can be effected a separation of the two classes of minerals from each other, assuming that the grinding has been sufficient to unlock all of the particles of different composition. The separation does not depend upon differences in specific gravity of the various minerals; in fact, the sulfides are usually heavier than the oxides, and some of the heaviest sulfide minerals are the easiest to float. A particle of mineral may be so large, however, that its weight will counteract its affinity for the film of the bubble. In most cases the ore must be fine enough to pass a screen having at least 48 meshes to the linear inch. Taggart defines flotation as follows : Flotation is a method of wet concentration of ores in which separation of mineral from gangue is effected by causing the mineral to float at or above the surface of a body of liquid pulp while the gangue becomes or remains submerged. The method

Jan 1, 1928

By John Chipman, Karl L. Fetters

Tax relationship between the composition of the slag and that of the underlying metal during the refining of a heat of liquid steel may best be studied in the light of the two broad physicochemical concepts of equilibrium and reaction rate. Actual steelmaking processes, typified by basic open-hearth practice, involve such complexities of operating variables that it is impossible to distinguish with any degree of certainty between the general limiting conditions imposed by chemical equilibrium and the effects associated with rates of diffusion or of chemical reaction. Further advances in the physical chemistry of steelmaking will depend upon our ability to distinguish clearly between these two kinds of effects, and the experimental work that must be done falls naturally into two classifications. The first is the study of chemical equilibrium that cannot be carried out with assurance under operating conditions but must be done in the laboratory. The second is the subject of rates of reaction and diffusion and the mechanism of the process as a whole, which can best be studied under operating conditions. The latter is not entirely independent of the former, since its interpretation often requires a knowledge of the equilibrium state. It is the purpose of this and of several papers that will follow to present the results of laboratory investigations of equilibria involving liquid steel and slag. Open-hearth slag is a complex mixture containing at least eight major components and perhaps twice as many whose influence may be classified as probably minor. It is not surprising that progress toward a complete understanding of such a material at high temperatures has been slow. Attempts to apply the established principles of physical chemistry to the behavior of the individual components of this mixture have been beset by an almost complete lack of data on its chemical properties in the liquid state. This has necessitated the adoption of various methods of approximation based upon such assumptions as, for example, that for a given component the ratio of its mol fraction in the slag to that in the metal is a constant, or that the molecular composition of the liquid slag is the same as its crystalline constitution after solidification. From the thermodynamic viewpoint, such assumptions are merely useful dodges, which enable one to hazard a guess as to the magnitude of the more fundamental quantities, the chemical potentials and activities of the components of slag. The problem of determining the activity of each substance in an eight-component system seems too complex to be undertaken without the aid of generalizations derived from experimental data on similar systems containing a smaller number of components. Accordingly, it was planned in the present investigation to study the equilibrium of molten iron with the simplest

Jan 1, 1941

By Karl Fetters, John Chipman

The relationship between the composition of the slag and that of the underlying metal during the refining of a heat of liquid steel may best be studied in the light of the two broad physicochemical concepts of equilibrium and reaction rate. Actual steel-making processes, typified by basic open-hearth practice, involve such complexities of operating variables that it is impossible to distinguish with any degree of certainty between the general limiting conditions imposed by chemical equilibrium and the effects associated with rates of diffusion or of chemical reaction. Further advances in the physical chemistry of steelmaking will depend upon our ability to distinguish clearly between these two kinds of effects, and the experimental work that must be done falls naturally into two classifications. The first is the study of chemical equilibrium that cannot be carried out with assurance under operating conditions but must be done in the laboratory. The second is the -subject of rates of reaction and diffusion and the mechanism of the process as a whole, which can best be studied under operating conditions. The latter is not entirely independent of the former, since its interpretation often requires a knowledge of the equilibrium state. It is the purpose of this and of several papers that will follow to present the results of labora- tory investigations of equilibria involving liquid steel and slag. Open-hearth slag is a complex mixture containing at least eight major components and perhaps twice as many whose influence may be classified as probably minor. It is not surprising that progress toward a complete understanding of such a material at high temperatures has been slow. Attempts to apply the established principles of physical chemistry to the behavior of the individual components of this mixture have been beset by an almost complete lack of data on its chemical properties in the liquid state. This has necessitated the adoption of various methods of approximation based upon such assumptions as, for example, that for a given component the ratio of its mol fraction in the slag to that in the metal is a constant, or that the molecular composition of the liquid slag is the same as its crystalline constitution after solidification. From the thermo-dynamic viewpoint, such assumptions are merely useful dodges, which enable one to hazard a guess as to the magnitude of the more fundamental quantities, the chemical potentials and activities of the components of slag. The problem of determining the activity of each substance in an eight-component svstem seems too complex to be undertaken without the aid of generalizations derived from experimental data on similar systems containing a smaller number of components. Accordingly, it was planned in the present investigation to study the equilibrium of molten iron with the simplest

Jan 1, 1941

By Karl Fetters, John Chipman

The relationship between the composition of the slag and that of the underlying metal during the refining of a heat of liquid steel may best be studied in the light of the two broad physicochemical concepts of equilibrium and reaction rate. Actual steel-making processes, typified by basic open-hearth practice, involve such complexities of operating variables that it is impossible to distinguish with any degree of certainty between the general limiting conditions imposed by chemical equilibrium and the effects associated with rates of diffusion or of chemical reaction. Further advances in the physical chemistry of steelmaking will depend upon our ability to distinguish clearly between these two kinds of effects, and the experimental work that must be done falls naturally into two classifications. The first is the study of chemical equilibrium that cannot be carried out with assurance under operating conditions but must be done in the laboratory. The second is the -subject of rates of reaction and diffusion and the mechanism of the process as a whole, which can best be studied under operating conditions. The latter is not entirely independent of the former, since its interpretation often requires a knowledge of the equilibrium state. It is the purpose of this and of several papers that will follow to present the results of labora- tory investigations of equilibria involving liquid steel and slag. Open-hearth slag is a complex mixture containing at least eight major components and perhaps twice as many whose influence may be classified as probably minor. It is not surprising that progress toward a complete understanding of such a material at high temperatures has been slow. Attempts to apply the established principles of physical chemistry to the behavior of the individual components of this mixture have been beset by an almost complete lack of data on its chemical properties in the liquid state. This has necessitated the adoption of various methods of approximation based upon such assumptions as, for example, that for a given component the ratio of its mol fraction in the slag to that in the metal is a constant, or that the molecular composition of the liquid slag is the same as its crystalline constitution after solidification. From the thermo-dynamic viewpoint, such assumptions are merely useful dodges, which enable one to hazard a guess as to the magnitude of the more fundamental quantities, the chemical potentials and activities of the components of slag. The problem of determining the activity of each substance in an eight-component svstem seems too complex to be undertaken without the aid of generalizations derived from experimental data on similar systems containing a smaller number of components. Accordingly, it was planned in the present investigation to study the equilibrium of molten iron with the simplest

Jan 1, 1941

By Bartlett W. Paulding

Since its introduction to the petroleum industry in 1949 by Clark,1 hydraulic fracturing or "hydrafracing" has developed into a widely respected and useful technique for increasing production from petroleum reservoirs. Even then, Clark described production increases of from 6 to 100 barrels of oil per day (bopd). Since that time, others have described treatments in which production increased from 12 to 456 bopd, from only a show to 40 bopd;2 from 48 to 219 bopd; 3 from 500 to 1400 bopd and from a show to 192 bopd.4 Although representative of only a few of many successful hydraulic fracturing operational6 these increases in production attest to the past and potential value of the hydrafracing technique to the petroleum industry. The technique has received a considerable amount of theoretical and experimental attention.1, 5-20 Unfortunately, however, the degree of general understanding of the mechanics of hydraulic fracturing is still inadequate to solve many recurring problems. The practicing engineer is plagued with difficulties in predicting such factors as: (1) the required pressure and viscosity of the fracturing fluid to not only induce the fracture but to control the extent of its growth, (2) the strength characteristics and amount of proppant to include in the fluid so that the fracture is held open once the fluid pressure is decreased, and (3) the volume of the reservoir influenced by the induced fractures and the resulting increase in production. A major cause of these difficulties is the uncertainty associated with determining the orientation of the hydraulically induced fractures. One's natural conclusion in considering the problem is that the orientation of the fracture would depend on several variables, as, for example, the relationship between the viscosity and injection rate of the fluid and the

Jan 1, 1968

By Hallet R. Robbins

Korea, the ancient" Hermit Kingdom," is a peninsula jutting out from the coast of eastern Asia. By the natives it is called " Chosen," nfhich, translated, means " Land of the Morning Calm." It lies between the Yellow sea and the Sea of Japan. On the north it is separated from Manchuria and the Russian province of Primorsk by the Yalu and Tiumen rivers; on the south the Korcan straits interpose a rough voyage of 120 nliles to the nearest point in Japan. The entire country is situated between the parallels of 34O and 42O N. latitude. The surface of the country is made up of successive ranges of ul~glaciated mountains, separated by narrow, fertile, and more or less densely populated, valleys. Through all the obscure centuries of its history, Korea has succeeded in maintaining a monastic seclusion, over which, from time immeniorial until the late Chino-Japanese war in 1894, China exercised a shadowy sovereignty. Although Korea had been forced into slight foreign contact previously, her first forcign treaty was signed with Japan in 1876. Under the restraining guardianship of China, the Japanese treaty bore but infiignificant innovations for Korea; but when, in 1883, a treaty was made with the United States, the first of the western nations, a decade after the American gunboats, under Commodore Rodgers and Lieutenant Schley, forced their may up the Salee river, Korea awoke from her sleep of 4,000 years. The Eorean peninsula suddenly became the arena where the enterprises and individuals of many foreign nations met in fiercest rivalry. Out of this struggle grew two singularly successful American enterprises, both of which have played an important part in developing the natural resources of the country. The first, and best known of these, is the Oriental Consolidated Mining Co., which was organized by Lcigh Hunt

Jan 1, 1909

By J. L. Stuck

Geological investigation and research have contributed greatly in making industrial minerals the basis of an important industry in the state. North Carolina contains a wide variety of industrial minerals and rock. Mica, feldspar, kaolin, halloysite, talc, pyrophyllite, silli-manite, and spodumene are used to illustrate the progress being made. IN a previous paper1 an attempt was made to indicate the importance of industrial minerals in North Carolina and the wide variety of such materials present. The present paper is concerned with geological investigation and research which have made industrial minerals the basis of an important industry in the state. Geological mapping has gone through three stages in North Carolina during the present century. The first stage is represented by excellent reports of which Corundum and the Peridotites of Western North Carolina,2 Volume I, now a classic, is representative. In this report, a geologic map of the western third of the state is shown on a scale of 10 miles to the inch. The next stage is represented by folios" of the U. S. Geological Survey published between 1902 and 1932. Most of these contained 30 min quadrangle maps on a scale of 2 miles to the inch. The third step is represented by reports prepared during the past 10 years which contain geological maps4 on scales varying from 500 ft to 1 mile to the inch, while many mine maps have been prepared on scales varying from 20 to 150 ft to the inch. As the scale on which geological mapping has been done has decreased, the amount of information secured has increased. Pratt and Lewis did excellent work on the peridotites of western North Carolina, but their maps lacked details. Keith and others added

Jan 1, 1952

By W. S. Ayres

I AM well aware that this subject is not strictly in the line of mining engineering, yet as it is a subject with which mining engineers at times have something to do, I have thought, perhaps, it might not be wholly out of place to communicate to the Institute something of the method used in determining deflection, and of its final issue. Having felt a need of some simple formula for determining the deflection of girders of uniform cross-section under any load, I have been led through the counsel of Mr. Frederick J. Slade, to whom I am indebted for many suggestions, to undertake a labor of which I shall in this paper give only some of the most important features. The results arrived at agree with those obtainable from the received formula; of Weisbach, Rankine, and others, but the expressions given by these authors, and by all others that I have at hand, are of such a form that they are not easily applied by those whose higher mathematics have become rusty from disuse, and they require, moreover, too much labor in their application to be of practical value. The general formula that I have adopted is similar to that given by Rankine, and is deflection = [mWl3 -El], in which l is the span, W the total load, E the modulus of elasticity, I the moment of inertia of the uniform cross-section of the girder, and m a factor depending for its value on the mode of distribution of the load. The problem then is to find the value of this factor m in the formula, and for some distributions of the load it leads to a number of mathematical difficulties. In this place I shall consider first the girder to be loaded symmet-

Jan 1, 1877

By Alfonso W. Ovalle

INTRODUCTION The block-caving mining method is one of the most economical ways existing today to extract ore from nature. It is undoubtedly the least costly of the underground systems and moreover it compares favorably to open-pit mining. In addition to its low cost characteristic, the block-caving mining method permits a great extraction volume as can be exemplified by El Teniente's output capacity of over 22 million tons of ore per year. These characteristics of block-caving give assurance that, even though it is a very old mining system, it will be a good answer to the many future large massive low ore grade deposits to come and a1 so to rep1 ace open-pi t mining as such operations get deeper with higher stripping ratios. These are the reasons that induce further study of block-caving. In this paper block-caving at El Teniente is analyzed with due consideration to the major problems that this mine will encounter. Emphasis is given to the factors influencing the mining of soft ore which accounts for most of the ore to be extracted in the next ten years. A separate paper is devoted to a major modification introduced to block-caving hard primary ore at El Teniente by means of LHD equipment extraction. DESCRIPTION OF THE PRESENT MINING Ore Production and Flow Over 62.000 tons per day of ore are extracted 359 days per year at the El Teniente Mine. The Teniente 8 train haulage level at 1.983 m takes 29.000 tons daily to the Col6n Concentrator. Two trains make the 8 km haul with 16 cars per train. Car capacity is 90 tons. The Teniente 5 train haulage level 298 m above takes 33.000 t per day to the old Sewell Concentrator. Ore is produced from three production areas in two different levels. The so called North Mine produces 42.000 tons daily from the Teniente 4 level 65 m above the Teniente 5 haulage level. The Central Mine produces 1.000 tons from the first hard rock block caved at the Te- niente 4 level. The combined 43.000 tons per day production is sent through inclined 2 m dia- meter raises to the Teniente 5 haul age level , where 33.000 tons are taken 2.5 km to the Sewell Concentrator and 9.000 tons are hauled 0.5 km to a 5 m diameter vertical ore pass which sends ore to Teniente 8. The haulage is by 7 trains, 15 gabble-bottom cars per train. Car capacity is 20 tons. The so called South Mine produces 19.000 tons per day from the Teniente 1 level 645 m above the Teniente 8 haulage level. Ore is transferred by 2 m diameter inclined raises to the Ten 1 Retram level 22 m below, where 5 trains with 20 Sandfor Day cars per train, 8 tons capacity per car, haul the ore 1.5 km to two vertical 5 m diameter ore passes which connect to Ten 8. Starting in 1982 the Central Mine will in- crease production to 6.000 tons per day. An in- dependent loop haulage system will start operat- ing at the Teniente 5 level to feed a new under- ground 1.372 mm (54 in.) gyratory crusher which will send minus 152 mm ore (9 in.) to Teniente 8. In two or three years time the North Mine will only feed the 33.000 tons to the Sewel 1 Concentrator with its old Teniente 5 haulage system. The Col6n Concentrator will be fed from the Central and South Mines. Figure 1 shows the transfer systems and ore flows. The Ore Body In plan view at the Teniente 4 level the ore body has a kidney shape 1.800 m long and between 400 to 700 m wide. The north-eastern section of the ore body was washed away by the Teniente River. At the Sub 5 Level, 125 m below Teniente 4, the mineralization completely surrounds the circular 1.000 m diameter steep-sided barren breccia pipe (Braden pipe) . The ore body rock is 73% andesite, 14% diori te, 13% dacite and 6% mineralized breccia. Most of this ore is secondary enrichment sulfides which apart from the dacite is strongly fractured being chal cocite, cove1ine , bornite and

Jan 1, 1981

By T. M. Morris, F. M. Lewis, W. C. Lay, Gordon M. Bell

Part I of this chapter is concerned with the description of and metallurgical data pertaining to the flotation circuits used in the London mill of the Tennessee Copper Co., at Copperhill, Tenn. The ores treated at the London mill are massive complex sulfides, in which pyrrhotite and pyrite are the predominant minerals. Other sulfides are chalcopyrite and sphalerite; magnetite is also of economic value. The approximate mineralogical analysis of the ore is shown in Table 1. [ ] The chalcopyrite and sphalerite are closely associated with pyrrhotite as shown by the tracings of micrographs (Fig. I), which are representative of the mill feed. Fig. la illustrates the type of locking between pyrrhotite and chalcopyrite; Fig. lb illustrates the way in which sphalerite is attached. Thesephotographs indicate that it is not practical to break all of these attachments. Hence, in order to produce concentrates with satisfactory grades and recoveries, most of the locked chalcopyrite particles must be recovered into the copper concentrate, and the locked sphalerite-pyrrhotite particles must be separated from the iron concentrate. A copper concentrate, a zinc concentrate, and an iron concentrate are made. Typical metallurgical results are tabulated in Table 2. HISTORICAL In 1922 the London mill started as a copper concentrator, with a capacity of 300 tpd, and in 1926 an additional flotation circuit was added to recover the iron sulfide remaining in the copper tailing. In 1927 a zinc flotation circuit was installed between the copper and the iron flotation circuits. This procedure was not satisfactory because the iron recovery was low, due to the

Jan 1, 1962

By E. J. Rapperport, J. P. Pemsler

We have made calculations to evaluate the sensitivity of atomic absorption as a technique to measure vapor pressure changes with temperature. Our conclusion, supported by the experimental findings presented in this work, is that the ultimate sensitivity of the technique is well below lo-' Torr. This magnitude of vapor pressure sensitivity makes the method extremely attractive for thermodynamic studies. Atomic absorption techniques have been used previously in this connection by Scatchard and Boyd' and by vidale2 with a much lower sensitivity reported. Scatchard and Boyd's work measured cadmium pressure over Ag-Cd alloys in the range 0.02 to 0.3 Torr, and Vidale estimated that sensitivities of only 10"5 to 10"6 Torr are to be expected. Atomic absorption appears to be particularly well-suited to thermodynamic studies for several reasons: A) It is extremely sensitive; our experiments indicate an ability to measure vapor pressure changes of 10"9 Torr. B) It is highly selective; there is seldom interference among the resonant wavelengths of the various species. C) It may be performed in an absorption cell under static conditions. This alleviates such problems as surface impoverishment of alloys, attainment of equilibrium, and temperature measurement and control. D) Simultaneous, or near-simultaneous, vapor pressure measurements may be made for several elements in a given system. Experimental. The physical basis of the technique is the highly selective absorption of particular wavelengths by specific atomic species. In most atomic absorption work the element of interest is incorporated into a hollow cathode lamp to provide a characteristic spectral source of high intensity. The spectra lines characteristic of the element in the cathode are attenuated by atoms of that element in the radiation path. Radiation from silver or cadmium hollow cathode lamps was directed along a path containing a 10-cm evacuated silica cell. The cell was positioned within a silica windowed furnace and contained silver, cadmium, or an Ag-Cd alloy. As the furnace temperature was elevated, the number of atoms of the absorbing element in the vapor phase within the cell rose, and the resonant radiation was increasingly absorbed. Intensities were measured by passing the radiation through a Techtron Model AA-4 one-half meter grating atomic absorption spectrometer equipped with a photo-multiplier detector. In order to minimize instabilities in the source, the hollow cathodes were allowed to warm up for several hours and were run at only 2 5 to 30 pct of their maximum rated amperage. In addition the attenuated beam was monitored before and after each reading. The attenuation of resonant wavelengths may be related to vapor pressure by the following relationships.

Jan 1, 1969

By R. F. Evans, J. M. Avert

Much has been written of the glamour of magnesium from sea water, the Aladdin-like creation of a huge magnesium plant in the Nevada desert using cheap hydroelectric power from Boulder Dam; the marvels of the Hansgirg process for the electrothermal reduction of magnesium oxide by carbon, and the ferrosilicon process for producing magnesium from dolomite. This is the story of the production of magnesium by the electrolytic process, using steam-electric power supplied by a public utility, in a plant at Painesville, Ohio, 30 miles east of Cleveland on the shore of Lake Erie. The story is not without interest, since it involves several unique developments that provide the answer to a question frequently asked: How is it possible to produce magnesium metal economically at such a location as Painesville, Ohio? Basically, the answer lies in making use of facilities already in existence for the production of soda ash, which makes it possible to manufacture magnesium chloride, the principal raw material, cheaply enough to offset the high cost of electric power. To this is coupled the successful conversion of by-product chlorine into a product required for the war program. The source of magnesium for this opera- tion is the enormous surface deposit of high-grade dolomite in the region south of Toledo, within reasonable freight haul of Painesville. This same geological stratum underlies the Painesville plant, but unfortunately at a depth of about 3000 ft.— apparently too great a depth to permit underground mining to compete with the delivered cost of rock from surface quarries in other areas. The cost of dolomite obviously is an important factor, since the rock contains only some 12 per cent magnesium (20 per cent MgO) so that one dollar on the cost of stone means more than $8 in terms of its magnesium content, and more than that in terms of recoverable magnesium metal. Production of Magnesia from Dolomite In the summer of 1941, the Diamond Alkali Co. was well along with construction of a plant intended for the commercial production of refractory and other grades of magnesia from dolomite. The process to be used was designed to make maximum economic advantage of existing plant and operations by tying the production of magnesia in with the manufacture of soda ash in such a way as to make use of the lime [CaO)., value of calcined dolomite. The process finally adopted after a lengthy research and development program has much in common with the old Clerc-Nihoul process, but includes certain innovations found to be necessary or advantageous. Essentially, the process is based upon the following series of reactions:

Jan 1, 1949

By Robert E. Green, Kenneth Reifsnider

Several experiments have been performed in order to illustrate the application of a recently developed X-ray image intensifier system to metallurgical investigations. In the present work the system has been used to study the instantaneous alterations in Laue transmission X-ray diffraction patterns during tensile deformation of aluminum single crystals. Expem'mental results are presented which demonstrate the capability of the system for crystal orientation, for following orientation changes due to lattice rotation during tensile deformation, and for showing changes in the homogeneity of the lattice planes along the specimen length as a function of strain rate. RECENTLY, a new X-ray system has been developed which incorporates a cascaded image intensifier and permits direct viewing and recording of X-ray diffraction patterns produced on a fluorescent screen.1"3 In the present work the results of several experiments are presented which demonstrate the usefulness of this system for metallurgical applications. EXPERIMENTAL PROCEDURE A schematic diagram of the experimental arrangement is shown in Fig. 1. In this system a Machlett AEG-50-S tungsten target X-ray tube, normally operated at 50 kv and 40 ma, serves as the X-ray source. The X-ray tube is placed in direct contact with a 10-in.-long collimator, which transforms the X-ray beam from one with a circular cross section to one with a rectangular cross section 3 in. high and 1/6in. wide. By blocking off all but a small portion of the rectangular slit, it is possible to work with the more conventional "pinhole" collimated X-ray beam commonly used for obtaining Laue diffraction patterns. In the present work the test specimens were 99.99+ pct aluminum single crystal wires & in. in diam and 3 in. long. For the deformation tests the wire crystals were mounted in a special set of grips in a table model Instron machine so that diffraction patterns could be recorded during specimen deformation. For the orientation tests the wire crystals were mounted in a rotating goniometer so that diffraction patterns could be recorded during specimen rotation. At a distance of 3 cm from the specimen axis, a 6 in. diam DuPont CB-2 fluorescent screen is positioned to transform the X-ray image to a visible one. A Super Farron f/0.87 72 mm coupling lens, corrected for 4 to 1 demagnification, transmits the visible image to the image tube. The image intensifier used is a three-stage magnetically focused RCA type C70021A with an S-20 input photocathode and a P-20 output phosphor. The tube has unity magnification and useful input and output screen diameters of 1.5 in. The image on the output phosphor is of sufficient intensity to be viewed directly, to be recorded cine-matographically, or to be displayed by vidicon pick-up on a television monitor. The recording device most commonly used is a 16 mm Bolex motion picture camera fitted with a Canon f/0.95, 50 mm lens. The overall gain of the system is 16,000 for direct viewing and 2240 for recording on 16 mm movie film. The resolution of the system is limited to 1 line pair per mm which is approximately that of the fluorescent screen. This system has been used for cine recording of transmission Laue X-ray diffraction patterns with exposure times as short as 1/220 sec and for vidicon television pick-up and display at a scan time of 1/30 sec. Quantitative information may be obtained from each frame of the movie film, by either stopping the vertical slit down to a point source in order to obtain a conventional Laue photograph or else by retaining the linear beam and introducing fiducial marks as described in a previous paper.4 In either case, each frame may be enlarged to appropriate size for analysis by either using a photographic enlarger and making prints of the desired frames, or, more conveniently, by using a microfilm reader. EXPERIMENTAL RESULTS The first series of photographs which are presented in Fig. 2 serves to demonstrate the usefulness of the system for crystallographic orientation determination. This series of prints, made from enlargements of a 16 mm movie film, shows the dynamic Laue transmission patterns produced by an aluminum single crystal wire which was rotating about the wire axis when the patterns were recorded. The movie films were taken at 16 frames per sec and the crystal was rotated at a rate of 15 rpm.

Jan 1, 1970

By H. F. Porter

MUCH has been written relative to the errors involved in the use of a galvanometer for measuring thermocouple electromotive forces. In general, it may be said that accuracy with a galvanometer is secured only at the sacrifice of durability, unless manual adjustment is made in the operation of the instrument to overcome the errors of resistance. and resistance changes. The pyrovolter and the potentiometer both require manual adjustment for every reading, readings being taken on a "null" method. To the end that some of these balances may be eliminated and only an occasional balance be made as a check reading, the "continuously deflecting pyrovolter" was developed. Essentially, the operation of the continuously deflecting pyrovolter is to determine the resistance of the thermocouple circuit, though its value is not noted or indicated, then throwing in series with the thermocouple sufficient resistance to bring the sum up to some standard value for which the indications of the galvanometer will be correct. This result may, however, be accomplished in a somewhat simpler manner, for which general method patents are now in the course of application. If we devise a galvanometer circuit so that by means of a simple adjustment the resistance of the entire circuit will be rendered equal to some constant predetermined value, we may rely on the galvanometer to give correct e.m.f. indications (assuming that the errors of temperature resistance coefficient and cold junction have been properly allowed for), and will indicate temperature continuously where the e.m.f. measured is developed by a thermocouple.

Jan 9, 1919

By Walton J. Greer, System By John E. Owen

The guard electrode system measures the resistivity of formations by employing a thin disk of current which is caused to flow perpendicular to the bore hole. The control of this current disk is obtained in a brute force manner through the use of relatively long equipotential electrodes above and below the measuring electrode. The log obtained from the system is free of "lag," "plateau," "shadow," "reflection" and other distortions evident on conventional logs. The proportionate contributions of the hole size and invaded zone resistivity to the apparent resistivity reading are reduced when the mud and filtrate resistivities are lower. Thus, the guard system favors the use of conductive muds. The mathematical development of the theory is given in an appendix. Equations are derived to evaluate the effects of mud resistivity, hole size, invaded zone resistivity and depth, and the true formation resistivity. Sample logs from several provinces are reproduced and compared with conventional electric logs to illsutrate the much greater detailed lithology that can be presented by the guard electrode system. INTRODUCTION With increased ability of those in the petroleum industry to analyze formation characteristics from electrical resistivity data, there has become apparent the need for more precise measures of that parameter. The measurement of the resistivity of a homogeneous and isotropic material can be made simply when the body of the material is infinite in all dimensions and the measuring electrodes can be placed within the body. In such a case, the current leaving an electrode follows a spherical distribution and the mathematical expression for the potential level at any distance from that electrode can readily be derived.'.' If it is considered that the active electrodes are within a bore hole filled with mud of a resistivity different from that of the formation. the current does not flow in a spherical pattern near the current source or sink, and the calculations of potential levels become more difficult. The additional consideration of a section of formation invaded by mud filtrates, and thus having resistivity different from either that of the mud, the adjacent formations or of the undisturbed formation, makes the mathematical problem extremely complex. Should the vertical dimensions of the formations be considered as finite. the problem becomes so complex as to preclude reasonable solution. Yet, even these considerations have not described adequately the conditions encountered in a large proportion of the wells to be studied. In efforts to evaluate the effects of the various conditions. combinations of twn, three. and four electrode logging con- figurations of the conventional types have been used. The resulting logs have left much to be desired in some provinces. It has become apparent that the use of such configurations will not result in adequate measurements being made, particularly in cases where the formation is composed of thin sections. If all the current of a resistivity measuring circuit is made to flow through the formation opposite the exploring electrode, many of the shortcomings of the conventional measuring system are eliminated. In the guard electrode method of electrical well logging to be discussed in this paper, the current is so controlled by causing it to flow in a thin disk normal to the axis of the logging tool. EARLY HISTORY The guard electrode method of electrical well logging in its early years was a joint development by the Geophysical Research Corp. and the Amerada Petroleum Corp. The method was first experimentally investigated by means of model studies. The results of these studies indicated that current focusing systems properly applied to electrical well logging

Jan 1, 1951